Construction of Building for Tool Room Training Centre (TRTC) at Plastic Park Gelapukhuri Tinsukia

Amount

CIVIL WORKS- GROUND FLOOR Earth work in excavation for foundation trenches of walls, retain -ing walls, footings of columns, steps, septic tanks etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all leads and lifts as directed and specified in following classification of soils including bailing out water where necessary as directed and specified. I) Upto a depth of 2m below the existing ground level . a) In ordinary soil

Earth/Sand filling in plinth in layers not more than 150 mm thk. including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensati -on, Forest Roalty, Sales Tax and other duties and taxes as may be necessary. I) With silt (Predominantly non plastic ) by truck carriage including loading and unloading .

Plain cement concrete work with coarse aggregate of sizes 13mm to 32mm in foundation bed for footings, steps, walls, brick work etc. as directed and specifoed including dewatering if necessary and curing complete (shuttering where necessary shall be be measured and paid separately). a) In Prop. 1 cement : 3 Sand : 6 Coarse agg. by volume

Providing and laying plain/reinforced cement concrete work with coarse sand & 20 mm down graded stone aggregate including dewatering if necessary and curing complete supply of materials but excluding cost of form work and reinfircement for reinforced cement concrete work ( form work and reinforcement will be measured and paid separately). (I) Using mixture machine (A ) In sub-structure upto plinth level. I) Foundations, footings, columns with base tie and plinth beam, grade beam ,pile cap ,base slab, retaining wall, walls of septic tank, inspection pit and the like and other works not less than 100mm thick upto plinth level. N) Without using admixture, plasticiser. b) M 20 grade concrete or Prop 1:1.5:3

B ) In super structure from plinth level up to 1st floor level. ii ) Columns, pillars, posts, struts, suspanded floor, roof, landing, shelf and support, balcony, lintel,sill band , beam, girder, cantilever,staircase (except spiral staircase and landing) including preparing of top surface and finishing of nosing. N) Without using admixture, plasticiser. b) M 20 grade concrete or Prop 1:1.5:3

iii) Vertical and horizontal fins (thickness not more than 100mm) individually or forming box louvre and projected band. N) Without using admixture, plasticiser. b) M 15 grade concrete or Prop 1:2:4

Providing and laying 25 mm thick damp proof course with cement concrete in prop. 1:1.5:4 with graded stone aggregate of 10mm down nominal size including providing approved damp proff mixture in prop. as recomended by the manufacturer including curing etc. complete as directed.

Providing brick soling in foundation and under floor with stone/ best quality picked jhama bricks, sand packed and laid to level and in panels after preparing the surface as directed including all labour and materials and if necessary dewatering complete. a) Brick on flat soling

Brick work in cement mortar with 1st class brick including racking out joints and dewatering if necessary and curing complete as directed in sub structure upto plinth level. (I) In Sub-structure upto plinth level including dewatering if necessary. b) In proportion 1:4

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately). (A) 112 mm thick brick wall. a) In cement morter in proportion 1:4( 1 cement :4 sand)

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc. hight of propping and centering below supporting floor to ceiling not exceeding 4 m and removal of the same for insitu reinforced cement concrete and plain concrete work in: Foundation, footing, base of columns, pile cap, raft and mass concrtete works etc. a) Using 38 mm thick plank

Sides of tie beams, plinth beams, grade beams etc.at or below ground level. (a) Using 38 mm thick plank

Columns, pillars ,posts & strut. a) Square, Rectangular, polygonal in plan or any shape like Tee/ L etc having plane vertical face. I) Using 38 mm thick plank

Sides and soffits of beams, beam haunching, cantilever girders, bressumers, lintels and horizontal ties. a) For depth not exceeding 1.0M. I) Using 38 mm thick plank

iii) Flat surface such as soffits of suspended floors, roofs, landings, cantilever slabs, chajjas balconies and the like. a) Floors etc. upto 200 mm in thickness. I) Using 38 mm thick plank

Vertical ties, fins, sun breaker, louvers, band, dropwalls etc. I) Using 38 mm thick plank.

Staircase with sloping or stepped soffits including risers and stringers but excluding landing.(using 38mm thick plank).

Providing form work of 12 mm thick plywood board and removal of the same in edges of slabs and breaks in floors and walls etc. of in -situ reinforced concrete works upto 1st floor level. a) Thickness not exceeding 200mm.

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side. b) In cement mortar 1:4

B) On fair side. b) In cement mortar 1:4

Extra for plastering on ceiling and soffits of stair up to 1st floor level including curing complete as directed. I) Ground floor

15 mm thick plain cement mortar bands in cement morter 1:4 in width including curing complete as directed. A) Up to 300 mm width. a) Flush Band

b) Sunk Band

Providing and laying 65mm thick C.C. floor with metallic concrete hardener topping under layer of 50 mm thick cement concrete 1:2:4 (1cement:2 coarse sand:4 coarse aggregate of 20 mm and down) and top layer of 15mm thick of metallic cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 stone aggregate 6 mm and down) by volume with which metallic hardening compound of approved quality is mixed in the ratio of 4:1 (4 parts of cement: 1 part of metallic floor hardening compound of approved quality by weight) including finishing with curing complete as directed.

Cement plaster skirting with cement mortar ( 1 cement : 3 coarse sand ) finished with a floating coat of neat cement including rounding of juctions with floor. b) 20 mm thick

Providing 18 mm thick Granite slab on vertical face of pedestal laid over 10 mm (1 cement :3 coarse sand ) jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as directed with approved quality of shade.

Providing polished granite slab of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile Choksey/Sika/Pedelite/Rouf) /white cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). (i) Normal Quality. (i) With Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)

Providing ceramic tiles of approved quality size, shape and thickness not less than 8 mm on floors , skirtings treads and risers of steps over cement mortar bed 10mm thick in prop 1:3 including cutting where necessary finished with flush pointing with Fix -A- Tiles (Choksey/ Sika/ Pedilite/Rouf )/ White cement slurry mixed with approved pigment to match shade of granite slab complete at all levels as specified and directed. a) Normal range ( Sizes 300mm x300mm and above). a) Orient made

Providing polished ceramic wall tiles of approved quality size, shape and thickness not less than 8 mm on walls and skirtings over cement mortar bed 10mm thick in prop 1:3 including cutting where necessary finished with flush pointing with Fix -A- Tiles (Choksey/ Sika/ Pedilite/Rouf )/ White cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. a) Normal range (Somany/ Orient/Nitco /Asian Make). i) Of size 200mmx300mm and above

Providing vitrified floor tiles of approved quality of special size, shape and thickness not less than 18 mm on floors, skirtings, risers, and treads of steps over 15mm thick base of cement mortar in prop 1:3 (1 cement :3 coarse sand ) including cutting where necesary finished with flush pointing with Fix -A-Tile ( Choksey/Sika/ Pedelite/Rouf/ White cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed polished ceramic wall tiles of approved quality size, shape and thickness not less than 8 mm on walls and skirtings over cement mortar bed 10mm thick in prop 1:3 including cutting where necessary finished with flush pointing with Fix -A- Tiles (Choksey/ Sika/ Pedilite/Rouf )/ White cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. a) Normal range (Somany/ Orient/Nitco /Varmora /Jhonson Make) ii) Of size 600mm x 600mm and above

Providing polished tiles of approved quality, size, shape of specified thickness on pavers over a base of 100mm compacted sand gravel including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (A) SUN ROCK HIGH CTS Tiles (Pavers) (a) Silicon (Pavers) 60 mm thick

Providing, fitting and fixing powder coated pressed steel door frame made of 1.25mm/ 1.6mm thick sheet of various sizes with necessary hinge jamb, lock jamb, head and steel base ties at the bottom of the frame. The whole frame shall be welded or rigidly fixed together by mechanical means with base ties of pressed mild steel angle of size 20x20x1.25mm thick. Frame to be filled up with 1:4:8 P.C.C. after fitting the frame with brick/ concrete works etc.complete as directed by the department for all levels. (P.C.C. to be measured and paid for seperately). (b) 1.60mm thick sheet. (iv) Size 125mm x 60mm (Double rebate)

Providing and fixing flush door shutters solid core construction with frame of first class hard wood with cross bend and face veneered plywood face panels conforming to relevant I.S. Code including oxidised iron butt hinges (100X75X3.5mm) 6 nos. with necessary wood screws. a) Decorative type face panel and block board core. I) 40 mm thick

Providing, fitting and fixing coloured anodised aluminium sliding windows and ventilators of standard sections of approved brand (HINDALCO/NALCO/BALCO/JINDAL/OTHER equivalent primary producer ) without horizontal glazing bars,joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rubber gasket, roller, bolting device, locking arrangements, screws etc as required complete as specified and directed for all levels. a) 3 track sliding window. ii) 5 mm frosted glass

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level). a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL. (ii)Super Ductile (SD) TMT reinforcement bars.

c) ISI approved Mild steel reinforcement bar(M.S.Bar)

Providing, fitting and fixing M.S. Grill of required pattern for winddows / clearstory windows / openings with M.S. flats at required spacing and farmed alround square or round M.S. bars with round headed bolts and nuts or screws. a) Ornamental Grill. c) Fixed to brickwork/ P.C.C/R.C.C.

Providing, fitting and fixing in position collapsible ms shutters with vertical channels 20 mm x 10 mm x 2mm braced with flat iron diagonals 200 x 5 mm size with top and bottom rails of T - iron 40mm x40mm x6mm with 38 mm dia steel pulleys complete with locking arrangment, handles including priming coat with red lead primer. I) Ground floor

Providing and fixing rolling shutters of approved make made of 80mm wide M.S. laths interlocked together through their entire lenth and jointed together at the ends by end-locks mounted on specially designed pipe shaft with bracket plates, guide channels and arrangements for inside and outside locking with push-pull operation complete including cost of wire, spring and hood cover for the shutters.

Providing and fixing Duraboard HD-100 premoulded compressible filler board at all heights and depths of minimum density 95kg/cum, non-staining having less than 1% water absorption, compression recovery of 93% (minimum) as per manufactured specification with polysulphide sealant to seal the expansion joint including preparation of surface, Polymer Modified Mortar (PMM) (Proportion 1cement: 3 sand:1 acrylic polymer) nozing, carriage of materials, cutting and placing to the required size complete at all levels as per drawings and direction of Engineer-in-Charge. (a) 25mm wide

Applying primary coat over new steel and other metal surfaces upto 100 mm in width or grith after preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and scoured with wire brushes fine steel wood scrappers and sand paper. a) With ready mixed red lead red oxide primer

Painting two coats ( excluding priming coat ) on new steel and other metal surfaces with enamel paint of approved brand and manufacture( Asian paint/Berger paint/ICI paint/ J &Npaint/Nerolac to give an even shade including cleaning the surface of all dirt, dust and other foreign matter. (I) Surfaces over 100 mm in width or girth. b) High gloss ( Asian paint/ Berger paint/ ICI paint / J& N paint / Nerolac).

Applying priming coat over new wood based surfaces over 10 cm in width/grith after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter, sand papering and knotting. a) With ready mixed paint, wood primer ( white).

Painting two coats ( excluding priming coat ) on new wood and wood based surfaces with enamel paint to give an even shade including cleaning the surface of ditrt, dust and other foreign material , sand papering and stopping. (I) Surfaces over 100 mm in width or girth. a) High gloss (Asian Paint/ Berger Paint /ICI paint/ J& N paint /Nerolac

Providing two coats of acrylic water based wall putty/ wall filter of Asian Paints/ Berger/Dulux (ICI)/ Nerolac over concrete/cement plaster/ brick walls ( internal )and after removing all the loosely adhering material from the wall/ceiling surface with the help of emerey stone ,putty blade or wire brush, moistening the wall with the help of sufficient quantity of clear water as specified and directed by the department.

c) Applying one coat of distemper primer of approved brand and manufacture on wall surfaces after thoroughly brushing the surface free from mortar drops and other foreign matter and including preparing the surface even and sand papered smooth.

Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a) Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

a) Providing one coat of cement primer( on ext. wall) of approved brand and manufacture on new surfaces after thoroughly brooming the surface preparing the surface even and sand papered smooth.

Finishing old /new wall with water proofing weather coat smooth anti-fungal premium textured exterior finish , finish of Sandex Matt brand of Snowcem India Ltd. Of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels ( two coats)

Pre-construction antitermite treatment at the bottom of foundation of foundation pits and walls on either side up to a height of 300m.m. from bottom of the excavation made for column ,plinth beam, wall trenches etc. by applying the emulsion @ 5 litres per sq.mt. Of the surface area before starting construction work( supplying of necesary tools and accessories by the contractor) as per the direction of the Department complete. a)with aquous emulsion having concentration 1:19 with chloropirophose solution (tricel or equivalent) and water ,I,e, 1% solution.

Providing plinth protection with bricks laid on edge and grouted with cement mortar 1:4 and finishing with cement pointing in prop. 1:1 complete.

Providing drain with brick work in cement mortar in proportion 1:5 with half brick thick side walls and 100mm thick C.C (1:3:6) base over one brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified. ii) 300mm wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm.

Supplying, fitting and fixing alluminum fittings of approved make reasonably smooth, free from sharp edges, flows and other defacts with counter sunk holes for screws including necessary aluminium screws etc. complete ( annodised to a bright natural mat or stain finish). a) Sliding door bolts. I) 300 X 16 mm

b) Tower bolt. I) 300 X 12 mm.

ii) 250 X 12 mm

c) Door handle. I) 150 mm

e) Butt hinge v ) 100 mm x75mmx 4mm

CIVIL WORKS- FIRST FLOOR Plain cement concrete floor base in prop1:3:6 laid in alternate bays as specified with coarse agg. of size 13mm to 32mm including dewatering if necessary, and curing etc. complete. b) 50mm thick

Providing and laying plain/reinforced cement concrete work with coarse sand & 20 mm down graded stone aggregate including dewatering if necessary and curing complete supply of materials but excluding cost of form work and reinfircement for reinforced cement concrete work ( form work and reinforcement will be measured and paid separately ). (I) Using mixture machine ii ) Columns, pillars, posts, struts, suspanded floor, roof, landing, shelf and support, balcony, lintel,sill band , beam, girder, cantilever,staircase (except spiral staircase and landing) including preparing of top surface and finishing of nosing. N) Without using admixture, plasticiser. b) M 20 grade concrete or Prop 1:1.5:3

Extra for each subsequent floor or part thereof above the first floor level.

iii) Vertical and horizontal fins (thickness not more than 100mm) individually or forming box louvre and projected band. N) Without using admixture, plasticiser. b) M 15 grade concrete or Prop 1:2:4. b) M 15 grade concrete or Prop 1:2:4

Extra for each subsequent floor or part thereof above the first floor level.

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately). (A) 112 mm thick brick wall. a) In cement morter in proportion 1:4( 1 cement :4 sand)

Extra for each subsequent floor or part thereof above the first floor level.

230mm thick brick wall in cement morter with 1st class brick including racking out joints and curing complete as directed in structure. (II) In superstructure above plinth level up to 1st floor level. b) In proportion 1:4

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc. hight of propping and centering below supporting floor to ceiling not exceeding 4 m and removal of the same for insitu reinforced cement concrete and plain concrete work in: Columns, Pillars , Posts & Strut. a) Square, Rectangular, polygonal in plan or any shape like Tee/ L etc having plane vertical face. I) Using 38 mm thick plank

Extra for each subsequent floor or part thereof above the first floor level.

Sides and soffits of beams, beam haunching, cantilever girders, bressumers, lintels and horizontal ties: a) For depth not exceeding 1.0M. I) Using 38 mm thick plank

Extra for each subsequent floor or part thereof above the first floor level.

iii) Flat surface such as soffits of suspended floors, roofs, landings, cantilever slabs, chajjas balconies and the like. a) Floors etc. upto 200 mm in thickness. I) Using 38 mm thick plank

Extra for each subsequent floor or part thereof above the first floor level.

Staircase with sloping or stepped soffits including risers and stringers but excluding landing.

Extra for each subsequent floor or part thereof above the first floor level.

Providing form work of 12 mm thick plywood board and removal of the same in edges of slabs and breaks in floors and walls etc. of in -situ reinforced concrete works upto 1st floor level. a) Thickness not exceeding 200mm

Extra for each subsequent floor or part thereof above the first floor level.

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side. b) In cement mortar 1:4

Extra for exterior plastering up to a height of first floor above ground level.

B) On fair side. b) In cement mortar 1:4

Extra for exterior plastering up to a height of first floor above ground level.

Extra for plastering on celling and soffits of stair up to 1st floor level (instead of plastering on walls) including curing complete as directed.

15 mm thick plain cement mortar bands in cement morter 1:4 in width including curing complete as directed. A) Up to 300 mm width. a) Flush Band

b) Sunk Band

c) Raised Band

Cement plaster skirting with cement mortar ( 1 cement : 3 coarse sand ) finished with a floating coat of neat cement including rounding of juctions with floor. b) 20 mm thick .

Providing 18 mm thick Granite slab on vertical face of pedestal laid over 10 mm (1 cement :3 coarse sand ) jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as directed with approved quality of shade.

Providing polished granite slab of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile Choksey/Sika/Pedelite/Rouf) /white cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). Normal Quality. (i) With Fix -A-Tile (Choksey/Sika/Pedelite/Rouf)

Providing ceramic tiles of approved quality size, shape and thickness not less than 8 mm on floors , skirtings treads and risers of steps over cement mortar bed 10mm thick in prop 1:3 including cutting where necessary finished with flush pointing with Fix -A- Tiles (Choksey/ Sika/ Pedilite/Rouf )/ White cement slurry mixed with approved pigment to match shade of granite slab complete at all levels as specified and directed. a) Normal range (Somany/ Orient/Nitco /Asian Make). i) Of size 300mmx300mm and above

Providing polished ceramic wall tiles of approved quality size, shape and thickness not less than 8 mm on walls and skirtings over cement mortar bed 10mm thick in prop 1:3 including cutting where necessary finished with flush pointing with Fix -A- Tiles (Choksey/ Sika/ Pedilite/Rouf )/ White cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. a) Normal range (Somany/ Orient/Nitco /Asian Make). i) Of size 200mmx300mm and above

Providing vitrified floor tiles of approved quality of special size, shape and thickness not less than 18 mm on floors, skirtings, risers, and treads of steps over 15mm thick base of cement mortar in prop 1:3 (1 cement :3 coarse sand ) including cutting where necesary finished with flush pointing with Fix -A-Tile ( Choksey/Sika/ Pedelite/Rouf/ White cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed polished ceramic wall tiles of approved quality size, shape and thickness not less than 8 mm on walls and skirtings over cement mortar bed 10mm thick in prop 1:3 including cutting where necessary finished with flush pointing with Fix -A- Tiles (Choksey/ Sika/ Pedilite/Rouf )/ White cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. a) Normal range (Somany/ Orient/Nitco /Varmora /Jhonson Make). ii) Of size 600mm x 600mm and above

Providing, fitting and fixing powder coated pressed steel door frame made of 1.25mm/ 1.6mm thick sheet of various sizes with necessary hinge jamb, lock jamb, head and steel base ties at the bottom of the frame. The whole frame shall be welded or rigidly fixed together by mechanical means with base ties of pressed mild steel angle of size 20x20x1.25mm thick. Frame to be filled up with 1:4:8 P.C.C. after fitting the frame with brick/ concrete works etc.complete as directed by the department for all levels. (P.C.C. to be measured and paid for seperately). (b) 1.60mm thick sheet. (iv) Size 125mm x 60mm (Double rebate)

Providing and fixing flush door shutters solid core construction with frame of first class hard wood with cross bend and face veneered plywood face panels conforming to relevant I.S. Code including oxidised iron butt hinges (100X75X3.5mm) 6 nos. with necessary wood screws. a) Decorative type face panel and block board core. I) 40 mm thick

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for RCC work / RB walling including straightening, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete ( upto first floor level ). a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL. (ii)Super Ductile (SD) TMT reinforcement bars.

Extra for each subsequent floor or part thereof above the first floor level.

c) ISI approved Mild steel reinforcement bar(M.S.Bar).

Extra for each subsequent floor or part thereof above the first floor level.

Providing, fitting and fixing M.S. Grill of required pattern for winddows / clearstory windows / openings with M.S. flats at required spacing and farmed alround square or round M.S. bars with round headed bolts and nuts or screws. a) Ornamental Grill. c) C) Fixed to brickwork /P.C.C./R.C.C.

Providing, fitting and fixing coloured anodised aluminium sliding windows and ventilators of standard sections of approved brand (HINDALCO/NALCO/BALCO/JINDAL/OTHER equivalent primary producer ) without horizontal glazing bars,joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rubber gasket, roller, bolting device, locking arrangements, screws etc as required complete as specified and directed for all levels. a) 3 track sliding window. ii) 5 mm frosted glass

Providing, fitting and fixing coloured anodised aluminium framed glazed doors with partition walls partly glass and partly prelaminated board with anodised aluminium frame made of 100mm x 43mm x 2mm sections of approved brand{ HINDALCO /NALCO/BALCO/JINDAL/ Other equivalent primary producer) with doors style of size 81mm x 43mm x 2mm, top rails 46mm x 43mm x 2mm, lock rails 81mm x 43mm x 2mm, fitting with glazing clip, special rubber type gasket complete including hydraulic floor spring pivot aluminium door handle lock angles cleat etc. complete as directed by the department at all levels. (i)6mm thick glass panes and 12mm prelaminated board.

Supplying, fitting, fixing and painting where necessary (one coat primer and two coats of paint) M/F Suspended Ceiling which includes G.I. Perimeter channels of size 0.55 thick (having one flange of 20 mm and another flange of 30 mm and a web of 27mm) along with perimeter of ceiling ,screw fixed to brick wall /partition with the help of nylon sleeves and screws at 610 mm c/c. Then suspending G.I. Intermediate channels of size 45 mm (0.9 mm thick with two equal flanges of 15mm each) from the soffit at 1220mm c/c with ceiling angle of width 25 mm x10mm x 0.55 mm thick fixed to soffit with G.I. Cleat and steel expansion fasteners. Ceiling section of 0.55 mm thickness having knurled web of 51.5 mm and two equal flanges of 26 mm each with lips of 10.5 mm are then fixed to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channels at 298 mm c/c. Then 12.5 mm thick square edge FuLtone/Sundance/Cratone/Louvertone/Textured Gypboard panels of size 595mmx 595mm (conforming to IS: 2095-1982 ) is then screw fixed to ceiling section with 25 mm long drywall screws at 290 mm c/c .Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment .Finally ,the boards are to be jointed and finished so as to have a flush lock which includes filling and finishing the tapered and square edges of the boards with jointing compound , joint paper tape and two coats of drywall topcoat suitable for Gypboard complete at all levels as specified and directed ( For light fittings, providing opening for doors, windows, ventilators etc cut out made with frame of perimeter channel supported suitably to be measured and paid separately where necessary). A) M.F. Frame Work with Design Type Textured Gypboard Tiles 9.5 mm thick

Applying primary coat over new steel and other metal surfaces upto 100 mm in width or grith after preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and scoured with wire brushes fine steel wood scrappers and sand paper. a) With ready mixed red lead red oxide primer.

Painting two coats ( excluding priming coat ) on new steel and other metal surfaces with enamel paint of approved brand and manufacture( Asian paint/Berger paint/ICI paint/ J &Npaint/Nerolac to give an even shade including cleaning the surface of all dirt, dust and other foreign matter. (I) Surfaces over 100 mm in width or girth. b) High gloss ( Asian paint/ Berger paint/ ICI paint / J& N paint / Nerolac).

Applying priming coat over new wood based surfaces over 10 cm in width/grith after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter, sand papering and knotting. a) With ready mixed paint, wood primer (White)

Painting two coats ( excluding priming coat ) on new wood and wood based surfaces with enamel paint to give an even shade including cleaning the surface of ditrt, dust and other foreign material , sand papering and stopping. (I) Surfaces over 100 mm in in width or girth. b) High gloss (Asian Paint/ Berger Paint /ICI paint/Nerolac

Providing two coats of acrylic water based wall putty/ wall filter of Asian Paints/ Berger/Dulux (ICI)/ Nerolac over concrete/cement plaster/ brick walls ( internal )and after removing all the loosely adhering material from the wall/ceiling surface with the help of emerey stone ,putty blade or wire brush, moistening the wall with the help of sufficient quantity of clear water as specified and directed by the department.

Applying one coat of distemper primer of approved brand and manufacture on wall surfaces after thoroughly brushing the surface free from mortar drops and other foreign matter and including preparing the surface even and sand papered smooth.

Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a) Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

Providing one coat of cement primer( on ext. wall) of approved brand and manufacture on new surfaces after thoroughly brooming the surface preparing the surface even and sand papered smooth.

Finishing old /new wall with water proofing weather coat smooth anti-fungal premium textured exterior finish , finish of Sandex Matt brand of Snowcem India Ltd. Of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels ( two coats)

Supplying, fitting and fixing anodised alluminium fittings of approved make reasonably smooth, free from sharp edges, flows and necessary aluminium screws etc. complete ( annodised to a bright natural mat or stain finish ). a) Sliding door bolts. I) 300 X 16 mm

b) Tower bolt. I) 300 X 12 mm

ii) 150 X 10 mm

c) Door handle. I) 150 mm

e) Butt hinge v) 100 mm x75mmx 4mm

Providing and fixing Duraboard HD-100 premoulded compressible filler board at all heights and depths of minimum density 95kg/cum, non-staining having less than 1% water absorption, compression recovery of 93% (minimum) as per manufactured specification with polysulphide sealant to seal the expansion joint including preparation of surface, Polymer Modified Mortar (PMM) (Proportion 1cement: 3 sand:1 acrylic polymer) nozing, carriage of materials, cutting and placing to the required size complete at all levels as per drawings and direction of Engineer-in-Charge. (a) 25mm wide

Supplying, providing, mixing and laying over waterproofing layers/ coatings with concrete screed of average 30mm thick or as per drawings/ requirements in proportion 1:2:4 (1cement : 2fine aggregate : 4coarse aggregate) (by volume) with 10mm and down well graded aggregates and admixed with a normal plasticizer like Master Plast PL-1 of Choksey Chemicals /Dr. Sealkit Normal Plast (Asian Chemicals)/Rheomac 707 of BASF @ 0.3% by weight of cement and thereafter scoring the top surface of the concrete screed @ 200mm c/c as specified and directed by the Department.

Supplying, fitting and fixing MAC blinds horizontal and vertical complete as specified and directed by the department at all levels. (A) Verticale Blinds. (a) Regular. i) 100mm

SANITARY WORKS Providing fitting and fixing vitreous water closet squatting pan (Indian type W.C Orissa pattern) with all fittings and fixtures complete including cutting and making good to the walls and floors whereever required. (Flushing Cistern to be paid separately). Indian type W.C Orissa pattern of size 580 x 440 mm . b) Coloured . ii) Hindware make

Providing fitting and fixing vitreous china pedestal type water closet (European type W.C pan 400mm high ) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately). B) Hindware make. b) Coloured. (v) Water closet UNIVERSAL "P (Cat.No.20012) (inclusive of seat cover)

Providing fitting and fixing vitreous china flat back type lipped front urinal basin of with automatic flushing cistern with standard flush pipe and CP brass spreader andbrass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required. (B) Hindware Make. (a) White. (iii) FB 610 x 410 x 380 (Cat. No.60002).

Providing fitting and fixing vitreous china squatting plate urinal with automatic flushing cistern with standard flush pipe and CP brass spreader andbrass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required. (A) Parryware Make. (ii) Coloured (Cat. No. C0573

Supplying, fiting and fixing automatic flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately). (ii) Hindware Make. (a) White. Auto Cister 10 litre (Cat. No.C61002).

Under Counter Basin. (B) Hindware Make. (a) White. (i) Lara (Cat. No.10095)

Providing fitting and fixing Decorative Mirror complete as directed and specified. (A) Parryware Make. (b) Size 600mm x 450mm

Providing, fitting and fixing recessed soap tray / soap dish complete as directed and specified. (A) Parryware Make . (ii) Wall Soap tray (Cat. No.C9951)

Providing, fitting and fixing CP towel rail complete as directed and specified. (a) Jaquar make. (i) Continental 300mm for wash basin (Cat.No. ACN-1101N)

Providing, fitting and fixing Chrome Plated TOILET PAPER holder complete as directed and specified. (a) Jaquar make . (ii) Continental toilet paper holder with flap (Cat.No. ACN-1153N)

Providing, fitting and fixing Chrome Plated bottle trap complete as directed and specified. (a) Jaquar make. (i) Bottle trap (with internal partition) 32mm size with 250mm long wall connection pipe (Cat.No. ALD-769)

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia

b) Concealed by chiselling or breaking brick wall/ C.C./ R.C.C and making good to the damages. (ii) 110mm dia

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia

b) Concealed by chiselling or breaking brick wall/ C.C./ R.C.C and making good to the damages. (ii) 110mm dia

Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. ii) 110 mm dia.

b) Concealed by chiselling or breaking brick wall/ C.C./ R.C.C and making good to the damages. (ii) 110mm dia

Supplying fiting and fixing PVC plain single tee of (Supreme /Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. ii) 110 mm dia.

b) Concealed by chiselling or breaking brick wall/ C.C./ R.C.C and making good to the damages. (ii) 110mm dia

Providing fitting and fixing 110 mm dia PVC Cowel with ISI make complete as directed and specified.

Providing fiting & fixing C.I. Grating to the floors complete as directed and specified. b) 100 mm dia

Providing fitting and fixing 450mm dia. 90mm thick C.I. Man hole cover and frame of 58 Kg. weight complete as directed and specified.

Construction of filter bed in soak pit including earth work in excavation of soil and then filling up of the trench with brick bats/Charcoal covered with earth over a layer of A.C. plain sheet above brick bat filling complete as directed. (sizes of soak pit may vary depending on the sizes and capacities of the septic tank as well as the number of users as mentioned in the table.

Construction of inspection pit inside measurement 450mm x450mm x450mm flush with 100mm diameter HCI/PVC pipes and cement concrete base in proportion 1:3:6 over flat brick soling, 12cm brick wall in cement mortar in proportion 1:4 finished with 13mm cement plaster in proportion 1:2 in side wall and floor. 450mm x450mm air tight C.I. inspection pit cover and frame complete including supplying of materials, necessary excavation of pit as directed.

WATER SUPPLY WORKS Supplying fitting and fixing approved uPVC Pipes of different sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. (A) Exposed or in trenches. SUPREME/ PRINCE/ SFMC BRAND or other equvalent approved brand (High presure pipe Sch-40) Exposed or in trenches. a) 50 mm dia

b) 40 mm dia

c) 32 mm dia

(B) Concealed by chieselling or breaking brick wall/ C.C. wall/ R.C.C. wall and making good to the damaged structure. SUPREME/ PRINCE / SFMC / FUSION BAND or other equvalent approved brand (High presure pipe Sch-40). d) 25 mm dia

e)20 mm dia

f)15 mm dia

Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately). II) Jaquar make. a) Continental/ Clarion. I) Standard

Supplying fitting and fixing Chrome plated (C.P.) stop -cock of approved brand and size as mentioned below as directed and specified ( G.I. & C.P. pipes will be measured and paid separately). I) Jaquar. (a) Continental /Clarion. (ii) 15 mm dia ( Angular stop cock)

Supplying and fitting fixing C.P. pillar cock of 15 mm dia of approved brand as specified and directed. ii) Jaquar make. b)Long neck with areator

Supplying fitting and fixing Chrome Plated (C.P.) sink cock of approved brand as directed and specified. (G.I. & C.P pipes will be measured and paid separately). v) Jaquar make. ii) Sink cock with raised 'J' shaped swinging spout

Supplying and fitting gun metal country pit valve ( full way valve) I.S.I Make as specified and directed. a) 50 mm dia

b) 40 mm dia

c) 25 mm dia

Supplying fitting and fixing gun metal check valve include necessary threads to pipes. a) 50 mm dia ( Heavy Type)

b) 40 mm dia( Heavy Type)

Supplying fitting and fixing check valve ( non return valve ) including threads to pipes. c) 40 mm dia

Supplying fitting and placing plastic cylindrical vertical closed top ( PCVC) tank of Sintex/ Polycon/ Patton make over the stagging with manhole cover with locking arrangement and cleaning arrangement including providing pads of sizes as required for inlet and outlet piped complete as directed with labour charge. ( I) 2000 litre capacity. (a) Sintex make

SEPTIC TANK Earth work in excavation for foundation trenches of walls, retain -ing walls, footings of columns, steps, septic tanks etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all leads and lifts as directed and specified in following classification of soils including bailing out water where necessary as directed and specified. I) Upto a depth of 2m below the existing ground level . a) In ordinary soil

Plain cement concrete work with coarse aggregate of sizes 13mm to 32mm in foundation bed for footings, steps, walls, brick work etc. as directed and specifoed including dewatering if necessary and curing complete (shuttering where necessary shall be be measured and paid separately). a) In Prop. 1 cement : 3 Sand : 6 Coarse agg. by volume

Providing and laying plain/reinforced cement concrete work with coarse sand & 20 mm down graded stone aggregate including dewatering if necessary and curing complete supply of materials but excluding cost of form work and reinfircement for reinforced cement concrete work ( form work and reinforcement will be measured and paid separately). (I) Using mixture machine (A ) In sub-structure upto plinth level. I) Foundations, footings, columns with base tie and plinth beam, grade beam ,pile cap ,base slab, retaining wall, walls of septic tank, inspection pit and the like and other works not less than 100mm thick upto plinth level. N) Without using admixture, plasticiser. b) M 20 grade concrete or Prop 1:1.5:3

Providing brick soling in foundation and under floor with stone/ best quality picked jhama bricks, sand packed and laid to level and in panels after preparing the surface as directed including all labour and materials and if necessary dewatering complete. a) Brick on flat soling

Brick work in cement mortar with 1st class brick including racking out joints and dewatering if necessary and curing complete as directed in sub structure upto plinth level. (I) In Sub-structure upto plinth level including dewatering if necessary. b) In proportion 1:4

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately). (A) 112 mm thick brick wall. a) In cement morter in proportion 1:4( 1 cement :4 sand)

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc. hight of propping and centering below supporting floor to ceiling not exceeding 4 m and removal of the same for insitu reinforced cement concrete and plain concrete work in: Foundation, footing, base of columns, pile cap, raft and mass concrtete works etc. a) Using 38 mm thick plank

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side. b) In cement mortar 1:4

B) On fair side. b) In cement mortar 1:4

Cement plaster skirting with cement mortar ( 1 cement : 3 coarse sand ) finished with a floating coat of neat cement including rounding of juctions with floor. b) 20 mm thick .

Providing and laying 65mm thick C.C. floor with metallic concrete hardener topping under layer of 50 mm thick cement concrete 1:2:4 (1cement:2 coarse sand:4 coarse aggregate of 20 mm and down) and top layer of 15mm thick of metallic cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 stone aggregate 6 mm and down) by volume with which metallic hardening compound of approved quality is mixed in the ratio of 4:1 (4 parts of cement: 1 part of metallic floor hardening compound of approved quality by weight) including finishing with curing complete as directed.

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for RCC work / RB walling including straightening, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete ( upto first floor level ). (ii)Super Ductile (SD) TMT reinforcement bars.

c) ISI approved Mild steel reinforcement bar(M.S.Bar).

ASSAM TYPE CANTEEN Earth work in excavation for foundation trenches of walls, retain -ing walls, footings of columns, steps, septic tanks etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all leads and lifts as directed and specified in following classification of soils including bailing out water where necessary as directed and specified. I) Upto a depth of 2m below the existing ground level . a) In ordinary soil

Earth/Sand filling in plinth in layers not more than 150 mm thk. including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensati -on, Forest Roalty, Sales Tax and other duties and taxes as may be necessary. I) With silt (Predominantly non plastic ) by truck carriage including loading and unloading .

Plain cement concrete work with coarse aggregate of sizes 13mm to 32mm in foundation bed for footings, steps, walls, brick work etc. as directed and specifoed including dewatering if necessary and curing complete (shuttering where necessary shall be be measured and paid separately). a) In Prop. 1 cement : 3 Sand : 6 Coarse agg. by volume

Providing and laying plain/reinforced cement concrete work with coarse sand & 20 mm down graded stone aggregate including dewatering if necessary and curing complete supply of materials but excluding cost of form work and reinfircement for reinforced cement concrete work ( form work and reinforcement will be measured and paid separately). (I) Using mixture machine (A ) In sub-structure upto plinth level. I) Foundations, footings, columns with base tie and plinth beam, grade beam ,pile cap ,base slab, retaining wall, walls of septic tank, inspection pit and the like and other works not less than 100mm thick upto plinth level. N) Without using admixture, plasticiser. b) M 20 grade concrete or Prop 1:1.5:3

B ) In super structure from plinth level up to 1st floor level. ii ) Columns, pillars, posts, struts, suspanded floor, roof, landing, shelf and support, balcony, lintel,sill band , beam, girder, cantilever,staircase (except spiral staircase and landing) including preparing of top surface and finishing of nosing. N) Without using admixture, plasticiser. b) M 20 grade concrete or Prop 1:1.5:3

Providing and laying 25 mm thick damp proof course with cement concrete in prop. 1:1.5:4 with graded stone aggregate of 10mm down nominal size including providing approved damp proff mixture in prop. as recomended by the manufacturer including curing etc. complete as directed.

Providing brick soling in foundation and under floor with stone/ best quality picked jhama bricks, sand packed and laid to level and in panels after preparing the surface as directed including all labour and materials and if necessary dewatering complete. a) Brick on flat soling

Brick work in cement mortar with 1st class brick including racking out joints and dewatering if necessary and curing complete as directed in sub structure upto plinth level. (I) In Sub-structure upto plinth level including dewatering if necessary. b) In proportion 1:4

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately). (A) 112 mm thick brick wall. a) In cement morter in proportion 1:4( 1 cement :4 sand)

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc. hight of propping and centering below supporting floor to ceiling not exceeding 4 m and removal of the same for insitu reinforced cement concrete and plain concrete work in: Foundation, footing, base of columns, pile cap, raft and mass concrtete works etc. a) Using 25 mm thick plank

Sides of tie beams, plinth beams, grade beams etc.at or below ground level. (a) Using 25 mm thick plank

Columns, pillars ,posts & strut. a) Square, Rectangular, polygonal in plan or any shape like Tee/ L etc having plane vertical face. I) Using 25 mm thick plank

Sides and soffits of beams, beam haunching, cantilever girders, bressumers, lintels and horizontal ties. a) For depth not exceeding 1.0M. I) Using 25 mm thick plank

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side. b) In cement mortar 1:4

B) On fair side. b) In cement mortar 1:4

Providing and laying 40mm thick C.C. floor with metallic concrete hardener topping under layer of 25 mm thick cement concrete 1:2:4 (1cement:2 coarse sand:4 coarse aggregate of 20 mm and down) and top layer of 15mm thick of metallic cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 stone aggregate 6 mm and down) by volume with which metallic hardening compound of approved quality is mixed in the ratio of 4:1 (4 parts of cement: 1 part of metallic floor hardening compound of approved quality by weight) including finishing with curing complete as directed.

Cement plaster skirting with cement mortar ( 1 cement : 3 coarse sand ) finished with a floating coat of neat cement including rounding of juctions with floor. b) 20 mm thick

Providing ceramic tiles of approved quality size, shape and thickness not less than 8 mm on floors , skirtings treads and risers of steps over cement mortar bed 10mm thick in prop 1:3 including cutting where necessary finished with flush pointing with Fix -A- Tiles (Choksey/ Sika/ Pedilite/Rouf )/ White cement slurry mixed with approved pigment to match shade of granite slab complete at all levels as specified and directed. a) Deluxe range (Somany/ Orient/Nitco /Qutone Make) i) Of Sizes 300mm x300mm and above)

Kota-stone slab flooring of 18 mm thick over 20mm thick base of cement plaster 1:6 (1 cement : 6 coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. (1) 550mm x 550mm

Providing 18 mm thick Granite slab on vertical face of pedestal laid over 10 mm (1 cement :3 coarse sand ) jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as directed with approved quality of shade.

Providing polished granite slab of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile Choksey/Sika/Pedelite/Rouf) /white cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). (i) Normal Quality (i) With Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)

Providing, fitting and fixing powder coated pressed steel door frame made of 1.25mm/ 1.6mm thick sheet of various sizes with necessary hinge jamb, lock jamb, head and steel base ties at the bottom of the frame. The whole frame shall be welded or rigidly fixed together by mechanical means with base ties of pressed mild steel angle of size 20x20x1.25mm thick. Frame to be filled up with 1:4:8 P.C.C. after fitting the frame with brick/ concrete works etc.complete as directed by the department for all levels. (P.C.C. to be measured and paid for seperately). (b) 1.60mm thick sheet. (iv) Size 125mm x 60mm (Double rebate)

Providing and fixing flush door shutters solid core construction with frame of first class hard wood with cross bend and face veneered plywood face panels conforming to relevant I.S. Code including oxidised iron butt hinges (100X75X3.5mm) 6 nos. with necessary wood screws. a) Decorative type face panel and block board core. I) 40 mm thick

Providing, fitting and fixing coloured anodised aluminium sliding windows and ventilators of standard sections of approved brand (HINDALCO/NALCO/BALCO/JINDAL/OTHER equivalent primary producer ) without horizontal glazing bars,joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rubber gasket, roller, bolting device, locking arrangements, screws etc as required complete as specified and directed for all levels. a) 3 track sliding window. ii) 5 mm frosted glass

Providing and fixing, in position suspended false ceiling using E-Grid (exposed ceiling suspension 2430 system) of grid size 600mm x 600mm/1200mmx600mm with main runner 38 x 24mm, cross tee 29mm x 24mm & wall angle 24mm x 24mm . Using 4mm/6mm thick High Pressure Steam Cured Non Asbestos Fibre Cement Board as per IS 14862, to be placed in a grid of G.I. system duly suspended with 4mm/6mm dia G.I/M.S bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts, sprinklers, smoke detectors etc. The main runners to be secured to structural soffit by hanger @ 1220mm maximum c/c. The last hanger at the end of each main runner should not be placed at more than 450mm from the adjacent wall. Flush fitting 1220mm cross tee to be interlocked between main runners @ 610mm c/c, so as to form 600mm x 600mm/1200mmx600mm grid, all complete as per the drawing & directions of engineer-in-charge. Finally, if specified, boards are to be painted with 2 coats of acrylic emulsion paint of approved shade/make over a coat of cement primer before installing it on the grid. (A) Standard Ceilings of Everest make or equivalent as directed by the departement. (i) Using 4 mm thick FC Board

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level). ISI approved TMT bar

c) ISI approved Mild steel reinforcement bar(M.S.Bar)

Providing, fitting and fixing M.S. Grill of required pattern for winddows / clearstory windows / openings with M.S. flats at required spacing and farmed alround square or round M.S. bars with round headed bolts and nuts or screws. a) Ornamental Grill. c) Fixed to brickwork/ P.C.C/R.C.C.

Providing, fitting, hoisting and fixing of roof trusses fabricated out of combination of any two or all of the following sections (i) Square section (ii) Rectangular Hollow section of specification RSH/SHS and (iii) M.S. circular hlollow section of Grade 210 including purlins, bottom runners and providing M.S. cleat, M.S. angle base plank, bolts and nuts with red oxide primer including fitting bottom runner and cleat etc. for fixing ceiling joist as per design complete as directed as per specifications. a) Using TATA make RHS/SHS of Grade 310 conforming to relevant I.S. code 4923 : 1997

Providing Pre Painted Galvalume Sheet Roofing (PPGL) at all levels including fitting and fixing self drilling, self tapping screws complete (Roof trusses, purlins etc. to be measured and paid separately.) TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by the Departement. (iii) 0.60 mm thick

Providing Pre Painted Galvalume Sheet (PPGL) accessories ( Ridges / Valley / Gutter / Flashing) at all levels including fitting and fixing self drilling, self tapping screws complete. TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by the Departement. (iii) 0.60 mm thick

Applying primary coat over new steel and other metal surfaces upto 100 mm in width or grith after preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and scoured with wire brushes fine steel wood scrappers and sand paper. a) With ready mixed red lead red oxide primer.

Painting two coats ( excluding priming coat ) on new steel and other metal surfaces with enamel paint of approved brand and manufacture( Asian paint/Berger paint/ICI paint/ J &Npaint/Nerolac to give an even shade including cleaning the surface of all dirt, dust and other foreign matter. (I) Surfaces over 100 mm in width or girth. b) High gloss ( Asian paint/ Berger paint/ ICI paint / J& N paint / Nerolac).

Applying priming coat over new wood based surfaces over 10 cm in width/grith after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter, sand papering and knotting. a) With ready mixed paint, wood primer ( white).

Painting two coats ( excluding priming coat ) on new wood and wood based surfaces with enamel paint to give an even shade including cleaning the surface of ditrt, dust and other foreign material , sand papering and stopping. (I) Surfaces over 100 mm in width or girth. a) High gloss (Asian Paint/ Berger Paint /ICI paint/ J& N paint /Nerolac

c) Applying one coat of distemper primer of approved brand and manufacture on wall surfaces after thoroughly brushing the surface free from mortar drops and other foreign matter and including preparing the surface even and sand papered smooth.

a) Providing one coat of cement primer( on ext. wall) of approved brand and manufacture on new surfaces after thoroughly brooming the surface preparing the surface even and sand papered smooth.

Supplying, fitting and fixing alluminum fittings of approved make reasonably smooth, free from sharp edges, flows and other defacts with counter sunk holes for screws including necessary aluminium screws etc. complete ( annodised to a bright natural mat or stain finish). a) Sliding door bolts. I) 300 X 16 mm

b) Tower bolt. I) 300 X 12 mm.

ii) 250 X 12 mm

c) Door handle. I) 150 mm

e) Butt hinge v ) 100 mm x75mmx 4mm

Pre-construction antitermite treatment at the bottom of foundation of foundation pits and walls on either side up to a height of 300m.m. from bottom of the excavation made for column ,plinth beam, wall trenches etc. by applying the emulsion @ 5 litres per sq.mt. Of the surface area before starting construction work( supplying of necesary tools and accessories by the contractor) as per the direction of the Department complete. a)with aquous emulsion having concentration 1:19 with chloropirophose solution (tricel or equivalent) and water ,I,e, 1% solution.

Providing plinth protection with bricks laid on edge and grouted with cement mortar 1:4 and finishing with cement pointing in prop. 1:1 complete.

Providing drain with brick work in cement mortar in proportion 1:5 with half brick thick side walls and 100mm thick C.C (1:3:6) base over one brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified. ii) 300mm wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm.

SANITARY WORKS Under Counter Basin. (B) Hindware Make. (a) White. (i) Lara (Cat. No.10095)

Providing fitting & fixing stainless steel kitchen sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings ,cutting &making good the walls wherever required. (Sink cock, stop cocks, waste coupling are to be paid separately. (A) Parryware Make. (ii) Single Bowl with Drain Board (160 x 180) Flat Edge - Glossy (Cat.No.C8538).

Providing fitting and fixing Decorative Mirror complete as directed and specified. (a) Double Arm Wall Mounted reversible plain / Magnifying (3X) Pivotal Mirror (Cat. No.ACN-1193N)

Providing, fitting and fixing recessed soap tray / soap dish complete as directed and specified. (A) Parryware Make . (ii) Wall Soap tray (Cat. No.C9951)

Providing, fitting and fixing CP towel rail complete as directed and specified. (a) Jaquar make. (v) Queen's - Grab bar (300mm long) (Cat.No.AQN-7711B)

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia

Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. ii) 110 mm dia.

Supplying fiting and fixing PVC plain single tee of (Supreme /Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. ii) 110 mm dia.

Providing fitting and fixing 110 mm dia PVC Cowel with ISI make complete as directed and specified.

Providing fiting & fixing C.I. Grating to the floors complete as directed and specified. b) 100 mm dia

WATER SUPPLY WORKS Supplying fitting and fixing approved uPVC Pipes of different sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. (A) Exposed or in trenches. SUPREME/ PRINCE/ SFMC BRAND or other equvalent approved brand (High presure pipe Sch-40) Exposed or in trenches. a) 50 mm dia

(B) Concealed by chieselling or breaking brick wall/ C.C. wall/ R.C.C. wall and making good to the damaged structure. SUPREME/ PRINCE / SFMC / FUSION BAND or other equvalent approved brand (High presure pipe Sch-40). d) 25 mm dia

f)15 mm dia

Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately). II) Jaquar make. a) Continental/ Clarion. I) Standard

Supplying fitting and fixing Chrome plated (C.P.) stop -cock of approved brand and size as mentioned below as directed and specified ( G.I. & C.P. pipes will be measured and paid separately). I) Jaquar. (a) Continental /Clarion. (ii) 15 mm dia ( Angular stop cock)

Supplying and fitting fixing C.P. pillar cock of 15 mm dia of approved brand as specified and directed. ii) Jaquar make. b)Long neck with areator

Supplying and fitting gun metal country pit valve ( full way valve) I.S.I Make as specified and directed. a) 50 mm dia

b) 40 mm dia

c) 25 mm dia

Supplying fitting and placing plastic cylindrical vertical closed top ( PCVC) tank of Sintex/ Polycon/ Patton make over the stagging with manhole cover with locking arrangement and cleaning arrangement including providing pads of sizes as required for inlet and outlet piped complete as directed with labour charge. ( I) 1000 litre capacity. (a) Sintex make

UTILITY BUILDING Earth work in excavation for foundation trenches of walls, retain -ing walls, footings of columns, steps, septic tanks etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all leads and lifts as directed and specified in following classification of soils including bailing out water where necessary as directed and specified. I) Upto a depth of 2m below the existing ground level . a) In ordinary soil

Earth/Sand filling in plinth in layers not more than 150 mm thk. including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensati -on, Forest Roalty, Sales Tax and other duties and taxes as may be necessary. I) With silt (Predominantly non plastic ) by truck carriage including loading and unloading .

Plain cement concrete work with coarse aggregate of sizes 13mm to 32mm in foundation bed for footings, steps, walls, brick work etc. as directed and specifoed including dewatering if necessary and curing complete (shuttering where necessary shall be be measured and paid separately). a) In Prop. 1 cement : 3 Sand : 6 Coarse agg. by volume

Providing and laying plain/reinforced cement concrete work with coarse sand & 20 mm down graded stone aggregate including dewatering if necessary and curing complete supply of materials but excluding cost of form work and reinfircement for reinforced cement concrete work ( form work and reinforcement will be measured and paid separately). (I) Using mixture machine (A ) In sub-structure upto plinth level. I) Foundations, footings, columns with base tie and plinth beam, grade beam ,pile cap ,base slab, retaining wall, walls of septic tank, inspection pit and the like and other works not less than 100mm thick upto plinth level. N) Without using admixture, plasticiser. b) M 20 grade concrete or Prop 1:1.5:3

B ) In super structure from plinth level up to 1st floor level. ii ) Columns, pillars, posts, struts, suspanded floor, roof, landing, shelf and support, balcony, lintel,sill band , beam, girder, cantilever,staircase (except spiral staircase and landing) including preparing of top surface and finishing of nosing. N) Without using admixture, plasticiser. b) M 20 grade concrete or Prop 1:1.5:3

Providing and laying 25 mm thick damp proof course with cement concrete in prop. 1:1.5:4 with graded stone aggregate of 10mm down nominal size including providing approved damp proff mixture in prop. as recomended by the manufacturer including curing etc. complete as directed.

Providing brick soling in foundation and under floor with stone/ best quality picked jhama bricks, sand packed and laid to level and in panels after preparing the surface as directed including all labour and materials and if necessary dewatering complete. a) Brick on flat soling

Brick work in cement mortar with 1st class brick including racking out joints and dewatering if necessary and curing complete as directed in sub structure upto plinth level. (I) In Sub-structure upto plinth level including dewatering if necessary. b) In proportion 1:4

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately). (A) 112 mm thick brick wall. a) In cement morter in proportion 1:4( 1 cement :4 sand)

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc. hight of propping and centering below supporting floor to ceiling not exceeding 4 m and removal of the same for insitu reinforced cement concrete and plain concrete work in: Foundation, footing, base of columns, pile cap, raft and mass concrtete works etc. a) Using 25 mm thick plank

Sides of tie beams, plinth beams, grade beams etc.at or below ground level. (a) Using 25 mm thick plank

Columns, pillars ,posts & strut. a) Square, Rectangular, polygonal in plan or any shape like Tee/ L etc having plane vertical face. I) Using 25 mm thick plank

Sides and soffits of beams, beam haunching, cantilever girders, bressumers, lintels and horizontal ties. a) For depth not exceeding 1.0M. I) Using 25 mm thick plank

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side. b) In cement mortar 1:4

B) On fair side. b) In cement mortar 1:4

Providing and laying 40mm thick C.C. floor with metallic concrete hardener topping under layer of 25 mm thick cement concrete 1:2:4 (1cement:2 coarse sand:4 coarse aggregate of 20 mm and down) and top layer of 15mm thick of metallic cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 stone aggregate 6 mm and down) by volume with which metallic hardening compound of approved quality is mixed in the ratio of 4:1 (4 parts of cement: 1 part of metallic floor hardening compound of approved quality by weight) including finishing with curing complete as directed.

Cement plaster skirting with cement mortar ( 1 cement : 3 coarse sand ) finished with a floating coat of neat cement including rounding of juctions with floor. b) 20 mm thick

Providing ceramic tiles of approved quality size, shape and thickness not less than 8 mm on floors , skirtings treads and risers of steps over cement mortar bed 10mm thick in prop 1:3 including cutting where necessary finished with flush pointing with Fix -A- Tiles (Choksey/ Sika/ Pedilite/Rouf )/ White cement slurry mixed with approved pigment to match shade of granite slab complete at all levels as specified and directed. aa) Deluxe range (Somany/ Orient/Nitco /Qutone Make) i) Of Sizes 600mm x600mm and above)

Providing, fitting and fixing powder coated pressed steel door frame made of 1.25mm/ 1.6mm thick sheet of various sizes with necessary hinge jamb, lock jamb, head and steel base ties at the bottom of the frame. The whole frame shall be welded or rigidly fixed together by mechanical means with base ties of pressed mild steel angle of size 20x20x1.25mm thick. Frame to be filled up with 1:4:8 P.C.C. after fitting the frame with brick/ concrete works etc.complete as directed by the department for all levels. (P.C.C. to be measured and paid for seperately). (b) 1.60mm thick sheet. (iv) Size 125mm x 60mm (Double rebate)

Providing and fixing flush door shutters solid core construction with frame of first class hard wood with cross bend and face veneered plywood face panels conforming to relevant I.S. Code including oxidised iron butt hinges (100X75X3.5mm) 6 nos. with necessary wood screws. a) Decorative type face panel and block board core. I) 40 mm thick

Providing, fitting and fixing coloured anodised aluminium sliding windows and ventilators of standard sections of approved brand (HINDALCO/NALCO/BALCO/JINDAL/OTHER equivalent primary producer ) without horizontal glazing bars,joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rubber gasket, roller, bolting device, locking arrangements, screws etc as required complete as specified and directed for all levels. a) 3 track sliding window. ii) 5 mm frosted glass

Providing and fixing, in position suspended false ceiling using E-Grid (exposed ceiling suspension 2430 system) of grid size 600mm x 600mm/1200mmx600mm with main runner 38 x 24mm, cross tee 29mm x 24mm & wall angle 24mm x 24mm . Using 4mm/6mm thick High Pressure Steam Cured Non Asbestos Fibre Cement Board as per IS 14862, to be placed in a grid of G.I. system duly suspended with 4mm/6mm dia G.I/M.S bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts, sprinklers, smoke detectors etc. The main runners to be secured to structural soffit by hanger @ 1220mm maximum c/c. The last hanger at the end of each main runner should not be placed at more than 450mm from the adjacent wall. Flush fitting 1220mm cross tee to be interlocked between main runners @ 610mm c/c, so as to form 600mm x 600mm/1200mmx600mm grid, all complete as per the drawing & directions of engineer-in-charge. Finally, if specified, boards are to be painted with 2 coats of acrylic emulsion paint of approved shade/make over a coat of cement primer before installing it on the grid. (A) Standard Ceilings of Everest make or equivalent as directed by the departement. (i) Using 4 mm thick FC Board

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level). ISI approved TMT bar

c) ISI approved Mild steel reinforcement bar(M.S.Bar)

Providing, fitting and fixing M.S. Grill of required pattern for winddows / clearstory windows / openings with M.S. flats at required spacing and farmed alround square or round M.S. bars with round headed bolts and nuts or screws. a) Ornamental Grill. c) Fixed to brickwork/ P.C.C/R.C.C.

Providing, fitting, hoisting and fixing of roof trusses fabricated out of combination of any two or all of the following sections (i) Square section (ii) Rectangular Hollow section of specification RSH/SHS and (iii) M.S. circular hlollow section of Grade 210 including purlins, bottom runners and providing M.S. cleat, M.S. angle base plank, bolts and nuts with red oxide primer including fitting bottom runner and cleat etc. for fixing ceiling joist as per design complete as directed as per specifications. a) Using TATA make RHS/SHS of Grade 310 conforming to relevant I.S. code 4923 : 1997

Providing Pre Painted Galvalume Sheet Roofing (PPGL) at all levels including fitting and fixing self drilling, self tapping screws complete (Roof trusses, purlins etc. to be measured and paid separately.) TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by the Departement. (iii) 0.60 mm thick

Providing Pre Painted Galvalume Sheet (PPGL) accessories ( Ridges / Valley / Gutter / Flashing) at all levels including fitting and fixing self drilling, self tapping screws complete. TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by the Departement. (iii) 0.60 mm thick

Applying primary coat over new steel and other metal surfaces upto 100 mm in width or grith after preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and scoured with wire brushes fine steel wood scrappers and sand paper. a) With ready mixed red lead red oxide primer.

Painting two coats ( excluding priming coat ) on new steel and other metal surfaces with enamel paint of approved brand and manufacture( Asian paint/Berger paint/ICI paint/ J &Npaint/Nerolac to give an even shade including cleaning the surface of all dirt, dust and other foreign matter. (I) Surfaces over 100 mm in width or girth. b) High gloss ( Asian paint/ Berger paint/ ICI paint / J& N paint / Nerolac).

Applying priming coat over new wood based surfaces over 10 cm in width/grith after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter, sand papering and knotting. a) With ready mixed paint, wood primer ( white).

Painting two coats ( excluding priming coat ) on new wood and wood based surfaces with enamel paint to give an even shade including cleaning the surface of ditrt, dust and other foreign material , sand papering and stopping. (I) Surfaces over 100 mm in width or girth. a) High gloss (Asian Paint/ Berger Paint /ICI paint/ J& N paint /Nerolac

c) Applying one coat of distemper primer of approved brand and manufacture on wall surfaces after thoroughly brushing the surface free from mortar drops and other foreign matter and including preparing the surface even and sand papered smooth.

a) Providing one coat of cement primer( on ext. wall) of approved brand and manufacture on new surfaces after thoroughly brooming the surface preparing the surface even and sand papered smooth.

Supplying, fitting and fixing alluminum fittings of approved make reasonably smooth, free from sharp edges, flows and other defacts with counter sunk holes for screws including necessary aluminium screws etc. complete ( annodised to a bright natural mat or stain finish). a) Sliding door bolts. I) 300 X 16 mm

b) Tower bolt. I) 300 X 12 mm.

ii) 250 X 12 mm

c) Door handle. I) 150 mm

e) Butt hinge v ) 100 mm x75mmx 4mm

Pre-construction antitermite treatment at the bottom of foundation of foundation pits and walls on either side up to a height of 300m.m. from bottom of the excavation made for column ,plinth beam, wall trenches etc. by applying the emulsion @ 5 litres per sq.mt. Of the surface area before starting construction work( supplying of necesary tools and accessories by the contractor) as per the direction of the Department complete. a)with aquous emulsion having concentration 1:19 with chloropirophose solution (tricel or equivalent) and water ,I,e, 1% solution.

Providing plinth protection with bricks laid on edge and grouted with cement mortar 1:4 and finishing with cement pointing in prop. 1:1 complete.

Providing drain with brick work in cement mortar in proportion 1:5 with half brick thick side walls and 100mm thick C.C (1:3:6) base over one brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified. ii) 300mm wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm.

SANITARY WORKS Providing fitting and fixing vitreous china pedestal type water closet (European type W.C pan 400mm high ) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately). B) Hindware make a) White (iii) Water closet POPULAR "P (Cat.No.20044) (inclusive of seat cover)

Supplying, fiting and fixing automatic flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately) B) Hindware make a) White Auto Cister 10 litre (Cat. No.C61002)

Under Counter Basin. (B) Hindware Make. (a) White. (i) Lara (Cat. No.10095)

Providing fitting & fixing stainless steel kitchen sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings ,cutting &making good the walls wherever required. (Sink cock, stop cocks, waste coupling are to be paid separately. (A) Parryware Make. (ii) Single Bowl with Drain Board (160 x 180) Flat Edge - Glossy (Cat.No.C8538).

Providing fitting and fixing Decorative Mirror complete as directed and specified. (a) Double Arm Wall Mounted reversible plain / Magnifying (3X) Pivotal Mirror (Cat. No.ACN-1193N)

Providing, fitting and fixing recessed soap tray / soap dish complete as directed and specified. (A) Parryware Make . (ii) Wall Soap tray (Cat. No.C9951)

Providing, fitting and fixing CP towel rail complete as directed and specified. (a) Jaquar make. (v) Queen's - Grab bar (300mm long) (Cat.No.AQN-7711B)

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia

Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. ii) 110 mm dia.

Supplying fiting and fixing PVC plain single tee of (Supreme /Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. ii) 110 mm dia.

Providing fitting and fixing 110 mm dia PVC Cowel with ISI make complete as directed and specified.

Providing fiting & fixing C.I. Grating to the floors complete as directed and specified. b) 100 mm dia

WATER SUPPLY WORKS Supplying fitting and fixing approved uPVC Pipes of different sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. (A) Exposed or in trenches. SUPREME/ PRINCE/ SFMC BRAND or other equvalent approved brand (High presure pipe Sch-40) Exposed or in trenches. a) 50 mm dia

(B) Concealed by chieselling or breaking brick wall/ C.C. wall/ R.C.C. wall and making good to the damaged structure. SUPREME/ PRINCE / SFMC / FUSION BAND or other equvalent approved brand (High presure pipe Sch-40). d) 25 mm dia

f)15 mm dia

Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately). II) Jaquar make. a) Continental/ Clarion. I) Standard

Supplying fitting and fixing Chrome plated (C.P.) stop -cock of approved brand and size as mentioned below as directed and specified ( G.I. & C.P. pipes will be measured and paid separately). I) Jaquar. (a) Continental /Clarion. (ii) 15 mm dia ( Angular stop cock)

Supplying and fitting fixing C.P. pillar cock of 15 mm dia of approved brand as specified and directed. ii) Jaquar make. b)Long neck with areator

Supplying and fitting gun metal country pit valve ( full way valve) I.S.I Make as specified and directed. a) 50 mm dia

b) 40 mm dia

c) 25 mm dia

Supplying fitting and placing plastic cylindrical vertical closed top ( PCVC) tank of Sintex/ Polycon/ Patton make over the stagging with manhole cover with locking arrangement and cleaning arrangement including providing pads of sizes as required for inlet and outlet piped complete as directed with labour charge. ( I) 1000 litre capacity. (a) Sintex make

EARTHFILLING, MASTER DRAIN (FRONT SIDE), RCC BOX CULVERT Raising low site around the building with approved soil obtained from outside by truck carriage including breaking clods, dressing etc. complete including paying necessary forest royelty, sales tax, land compensation, municipal gate fees, if any monopoly duty etc. (profile measurement to be taken and 12.5% deduction for shrinkage to be made from total quantity) etc. complete as directed and specified. (c) Other than Guwahati city .

Plain cement concrete work with coarse aggregate of sizes 13mm to 32mm in foundation bed for footings, steps, walls, brick work etc. as directed and specifoed including dewatering if necessary and curing complete (shuttering where necessary shall be be measured and paid separately). a) In Prop. 1 cement : 3 Sand : 6 Coarse agg. by volume

Providing and laying plain/reinforced cement concrete work with coarse sand & 20 mm down graded stone aggregate including dewatering if necessary and curing complete supply of materials but excluding cost of form work and reinfircement for reinforced cement concrete work ( form work and reinforcement will be measured and paid separately). (I) Using mixture machine (A ) In sub-structure upto plinth level. I) Foundations, footings, columns with base tie and plinth beam, grade beam ,pile cap ,base slab, retaining wall, walls of septic tank, inspection pit and the like and other works not less than 100mm thick upto plinth level. N) Without using admixture, plasticiser. b) M 20 grade concrete or Prop 1:1.5:3

Providing brick soling in foundation and under floor with stone/ best quality picked jhama bricks, sand packed and laid to level and in panels after preparing the surface as directed including all labour and materials and if necessary dewatering complete. a) Brick on flat soling

Brick work in cement mortar with 1st class brick including racking out joints and dewatering if necessary and curing complete as directed in sub structure upto plinth level. (I) In Sub-structure upto plinth level including dewatering if necessary. b) In proportion 1:4

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side. b) In cement mortar 1:4

B) On fair side. b) In cement mortar 1:4

Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor. (b) 20 mm thick

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc. hight of propping and centering below supporting floor to ceiling not exceeding 4 m and removal of the same for insitu reinforced cement concrete and plain concrete work in: Sides of tie beams, plinth beams, grade beams etc.at or below ground level. (a) Using 38 mm thick plank

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) b) Other ISI approved TMT reinforcement bar (SAI/BISCON/THERMAX) (For Assam Type Bldg., drain works,,retaining wall&boundary wall etc. .

c) ISI approved Mild steel reinforcement bar(M.S.Bar)

FIRE FIGHTENING WORKS Providing , Fixing , testing & Commissioning of Single Headed Gun Metal ISI Marked oblique pattern Hydrant Landing Valve with 80mm dia flanged inlet & 63mm dia instantaneous type female outlet complete with cap and chain, twist release lug and all accessories as per IS:5290-19833(Type A) and specifications complete as required.( MAKE: ESSEL/WINCO/NEWAGE/GETECH/MINIMEX)

Providing controlled percolating (C.P ) Hose ISI ,Marked (IS :8423) 63mm dia x 15M long complete with instantaneous type Gun Metal 63 mm dia ISI Marked male & female couplings (IS :903) bound & riveted to hose pipes with copper rivets and copper wire complete as required (MAKE : NIRMAL RUBBER/ NEWAGE/ GETECH/MINIMEX)

Providing& fixing of weather proof hose cabinets fabricated from 16 S.W.G. M.S. Sheet with centre opening full front glass door and locking arrangement , suitable to accommodate one landing valve (Yard Hydrant), 2nos 15 M long hoses and 1 no Branch pipe with nozzle. The cabinet shall be painted with one coat of primer and 2 or more coats of synthetic enamel paint of approved make & shade and shall be suitable mounted on a raised masonry platform complete as reqd.(MAKE:SELF FABRICATED) A. 900X600X450

Providing & Fixing of Gun Metal 63mm dia Short Branch Pipe with 20 mm dia nozzle , ISI marked (IS:903) Complete as required (Make ESSEL/WINCO/NEWAGE/GETECH /MINIMEX)

Providing & Fixing of Gun Metal Fire Brigade Connection ((inlet collection head) consisting of 63 mm instantaneous type male coupling with built in check valve and 150 mm dia flanged outlet complete with bolts, nuts and rubber insertions as per IS:904-1983 complete as reqd.(MAKE ESSEL/ WINCO/NEWAGE/ GETECH/MINIMEX) A)02 WAY

Providing , Fixing ,Testing & Commissioning of air Release Valve. A)25mm dia

Providing, Fixing, Testing & Commissioning of Mild Steel Black Pipe ( IS:1239 part -I) medium class including cutting, screwing, welding etc and providing all fittings viz forged steel screwed fitting upto 50mm dia and bolt welded above 50mm dia flanges, bends, tees, reducers, elbow, clamps, hangers etc including cutting holes and chases in brick or RCC walls/ slabs and making good the same to the approval of Engineer -in- charge / consultant complete including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade including steel work complete as required (Make : Tata / Jindal / Nezone) c. 100 mm dia

Supplying & Fixing Cast iron body Non Return valves complete with matching flanges, rubber insertion, nuts, bolts and washer etc(IS:5312) of following sizes complete as reqd.(Make : KOLEY/ KALPANA/AUDCO) B) 100 mm dia.

Supplying, installing , fixing of dry chemical powder fire extinguisher conforming to IS: 2171 with ISI mark and CO2 cartridge will be conforming to IS : 4947 with IS: 4308 with ISI mark , Powder will be confirming to IS: 4308 with ISI Mark(10 Kg) BRAND: FIRESTOP/FIREND/ FIRE SHIELD/GETECH/MINMEX

BOUNDARY WALL WITH GATE Earth work in excavation for foundation trenches of walls, retain -ing walls, footings of columns, steps, septic tanks etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all leads and lifts as directed and specified in following classification of soils including bailing out water where necessary as directed and specified. I) Upto a depth of 2m below the existing ground level . a) In ordinary soil

Plain cement concrete work with coarse aggregate of sizes 13mm to 32mm in foundation bed for footings, steps, walls, brick work etc. as directed and specifoed including dewatering if necessary and curing complete (shuttering where necessary shall be be measured and paid separately). a) In Prop. 1 cement : 3 Sand : 6 Coarse agg. by volume

Providing and laying plain/reinforced cement concrete work with coarse sand & 20 mm down graded stone aggregate including dewatering if necessary and curing complete supply of materials but excluding cost of form work and reinfircement for reinforced cement concrete work ( form work and reinforcement will be measured and paid separately). (I) Using mixture machine (A ) In sub-structure upto plinth level. I) Foundations, footings, columns with base tie and plinth beam, grade beam ,pile cap ,base slab, retaining wall, walls of septic tank, inspection pit and the like and other works not less than 100mm thick upto plinth level. N) Without using admixture, plasticiser. b) M 20 grade concrete or Prop 1:1.5:3

B ) In super structure from plinth level up to 1st floor level. ii ) Columns, pillars, posts, struts, suspanded floor, roof, landing, shelf and support, balcony, lintel,sill band , beam, girder, cantilever,staircase (except spiral staircase and landing) including preparing of top surface and finishing of nosing. N) Without using admixture, plasticiser. b) M 20 grade concrete or Prop 1:1.5:3

Providing brick soling in foundation and under floor with stone/ best quality picked jhama bricks, sand packed and laid to level and in panels after preparing the surface as directed including all labour and materials and if necessary dewatering complete. a) Brick on flat soling

Brick work in cement mortar with 1st class brick including racking out joints and dewatering if necessary and curing complete as directed in sub structure upto plinth level. (I) In Sub-structure upto plinth level including dewatering if necessary. b) In proportion 1:4

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc. hight of propping and centering below supporting floor to ceiling not exceeding 4 m and removal of the same for insitu reinforced cement concrete and plain concrete work in: Foundation, footing, base of columns, pile cap, raft and mass concrtete works etc. a) Using 38 mm thick plank

Sides of tie beams, plinth beams, grade beams etc.at or below ground level. (a) Using 38 mm thick plank

Columns, pillars ,posts & strut. a) Square, Rectangular, polygonal in plan or any shape like Tee/ L etc having plane vertical face. I) Using 38 mm thick plank

Sides and soffits of beams, beam haunching, cantilever girders, bressumers, lintels and horizontal ties. a) For depth not exceeding 1.0M. I) Using 38 mm thick plank

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level). ISI approved TMT bar

Supplying, fitting and fixing double leaf heavy duty iron gate, frame made from 50mm x 6mm M.S. flat iron with another horizontal flat at the middle, 20mm dia M.S bars at 200mm apart from bottom flat to top flat and 20 mm dia M.S. bars at 200mm apart from bottom flat to middle flat including drilling, welding etc. complete. All vertical bars are to be protruded at least 100mm above the middle and top flat is to be flattended and pointed as directed. Necessary locking arrangement on both faces, arrangement for temporary closing the gate and 2 nos.( minium) strong iron hinges of M.S bars and flat of same sizes on each leaf to be embeded in C.C brick pillars as necessary including a red oxide painting to all iron works as directed and specified. (Separate payment will be made for posts).

Supplying, fitting and fixing chain link fencing of 10 S.W.G, G.I. Wire 50mm x50mm mesh fitted to M.S angle iron post at 2000mm apart of specification detailed below including supplying, fitting and fixing hooks, eye bolts with nuts, staples and bolts including three horizontal lines of G.I wire 10 S.W.G at top,middle and bottom and with one vertical line to each fencing post for keeping the fencing tight and erect complete, including one coat of primer painting to M.S angle iron post in P.C.C base etc. with following. a) Corner and end posts with M.S angle of size 50mmx50mmx 5mm and length not less than 1800mm only duly slotted and bottom torqued with two numbers as stay posts. b). Intermediate post with M.S angle of size 40mmx40mmx5mm and length not less than 1800mm only duly slotted and bottom torqued and splayed. c).Stay post with M.S angle of size 35 mmx35mmx5mm and length not less than 1800mm duly slotted and bottom torqued and splayed. All M.S angle iron posts are to be fitted to P.C.C base embedded not less than 600mm (P.C.C. work shall be measured and paid separately).

Providing one coat of cement primer( on ext. wall) of approved brand and manufacture on new surfaces after thoroughly brooming the surface preparing the surface even and sand papered smooth.

Finishing old /new wall with water proofing weather coat smooth anti-fungal premium textured exterior finish , finish of Sandex Matt brand of Snowcem India Ltd. Of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels ( two coats)

LANDSCAPING & PAVER BLOCK Supplying and planting of plants in required size of pot including filling the pot to the top surface with appropriate soil media of garden soil, river sand , cow-dung, leaf mould, fertilizer , pesticides as per specification and necessary maintenance for a period of 4 month from the date of planting complete as specified and directed. ( Mixing of different ingredients of soil media to be made in presence of Deptt. Official/ Specialist concerned) ( A) With Bottle palm. I) Using earthen pot of 30cm dia

Supplying and planting of suitable plant materials for edge making (20cm wide) including the preparation of the ground by mixing organic manure and fertilizers as per spefication and necessary maintenance for a period of one year from the date of planting complete as specified and directed. ( A) Adopting Single Row Planting Method ( I) With Duranta

Supplying and plantting of ornamental shrub (plant saplling height 1'-0") including pit making (60 cm x 60cmx60cm) , filling the pit with appropriate soil media , manure and fertilizers and necessary maintenance for a period of one year from the date of planting complete as specified and directed. B) Bougainvillea

D) Thuja

Providing and laying of inter locking concrete block pavement (ICBP) with cement concrete paver blocks as per IS 15658-2006 of thickness 80mm and 28 days compressive strength not less than 30 N/m over a layer of bedding sand of compacted thickness 30mm, laid either in stretcher/ running/ herringbone pattern of bonds as directed by the engineer and in proper level and grade and compacted with appropriate equipment such as plat vibrator along with spreading of a thin layer of joint filling sand to fill up the gaps between blocks including construction of edge restraint wherever required complete as per drawings and Technical specification clause 1504 of MORTH.

Granular Sub-Base with Coarse Graded Material ( Table:- 400- 2) (Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC,and compacting with vibratory roller to achieve the desired density,complete as per cl. 401 for grading- II Material

INTERNAL ELECTRICAL WORKS Wiring for light/ fan/ call bell point with 2x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco or Equivalent Make as approved by the Deptt.) in recessed conduit wiring system with 2 mm thick 20mm dia rigid low halogen SFT PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) complete. SP upto 3.00 metre length.

MP upto 6.00 metre length.

LP upto 10.00 metre length.

Wiring to 5 a pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco or Equivalent Make as approved by the Deptt.) in recessed 2 mm thick rigid low halogen SFT PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete. SP upto 3.00 metre length.

MP upto 6.00 metre length.

LP upto 10.00 metre length.

Wiring for 5 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system including earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 2 mm thick 20 mm. dia. rigid low halogen SFT PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) SP upto 3.00 metre length.

MP upto 6.00 metre length.

LP upto 10.00 metre length.

Wiring for circuit wiring with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system. With 3 x 1.5 sq. mm. cable in 20 mm dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system. With 2 x 2.5 sq. mm. + earth continuity with 1x1.5 sq. mm. in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

With 2 x 4 sq. mm. + earth continuity with 1x2.5 sq. mm. cable in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

With 2 x 6 sq. mm. + earth continuity with 1x 4 sq. mm. cable in 25 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel or Equivalent Make as approved by the Deptt.) in surface/ recessed PVC 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system. With 4 x 10 sq. mm. + earth continuity with 2x6 sq. mm. cable in 40 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

With 4 x 16 sq. mm. + earth continuity with 2x10 sq. mm. cable in 40 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Supplying including installation of socket outlet 10/16 Amps 3/5 pin combine shuttered complete , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying including installation of socket outlet 6/10/13 Amps INTERNATIONAL SOCKET , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting fixing of 16 amp one way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting fixing of 6/10 amp one way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying including and fixing of following Metal boxes for MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) in surface/ recessed system complete as per direction of department. 3 module

6 module

12 module

Supplying including fitting fixing of following MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) front plate of suitable colour as per direction of department. 3 module

6 module

12 module

Supplying with fitting fixing of blank plate single in modular switch system , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying fitting and fixing industrial Plug & Socket in surface mounting SPN sheet steel powder painted MCB DB incorporated with MCB DIN rail, neutral link Earth bar of the following rating of DP MCB complete with making necessary connection etc. as specified and directed by the Deptt. 20A Capacity. (ABB, Schneider MG, legrand, Hager make)

Supplying fitting & fixing of LED Kubik Batten tube light fitting 300mm length as required and as directed by the department ( Jaquar or eqvt. make). kubik Series Batten tube fitting 10W

kubik Series Batten tube fitting 20W

Supplying, installation, testing and Commission of the following indoor Decorative Recess mounted LED down lighter luminaries of model no-DN 394B LED 16 S -6500 PSU WH / MV1857RLOO / MV1840RLOO /MV1830RLOO / MV1830RLOO / MV1857R500 / MV1857R500 / MV1840RLOO / CRDL11R023HP57 complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Philips / LT / Wipro make).

Supplying, installation, connection, testing and commissioning of surface/suspended LED luminaries with IP65 protection complete with all accessories including driver in the ceiling/ wall by providing necessary mounting bracket etc, and necessary connection with 1.5 sq mm. PVC. insulated S.C. copper conductor as required and as directed by the department.

Supplying with fitting and fixing of electronic chime MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department.

Installation of earth station with 40mm dia and 4.5 mtr. long GI pipe with necessary GI reducing socket 40mmx20mm size locking arrangement with hinged cover plate, funnel, GI nuts, thorough bolts etc.for putting pipe and refitting with necessary enclosure on the top etc. as required complete.

Extra for using salt 5Kg and charcoal 64 Kg. for pipe earth electrode as required.

Supplying and laying with 6 SWG GI earth wire at 0.50 mtr. below ground level or conductor earth electrode including soldering, excavation work and refitting etc.as required complete.

Supplying including fitting fixing of following star rated A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection cable, as approved by the Deptt.s etc. as required complete and as directed by the Department [Without regulator]. (ORIENT PSPO make / Usha make/ CROMPTON make/ Havells/ ATC/ V GAURD make) Energy efficient 5-star 1200 mm sweep. ORIENT PSPO / Usha / CROMPTON / Havells/ ATC or equivalent make

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. Power Flow 225 mm sweep (ORIENT make)

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 surface mounting SPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. ABB, Schneider MG, legrand, Hager make) 12 way SPN double door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof reversible Double door IP-43 double door surface mounting horizontal TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. ABB, Schneider MG, legrand, Hager make) 4way TPN (4+12) double door

6 way TPN (8+18) double door

Supplying with fitting and fixing single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. C Series (Schneider MG, legrand, Hager make) 6-32A

Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 30mA sensitivity DP RCCB (ABB, Schneider MG, legrand, Hager make) 40A

Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz 4P RCCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 100/300mA sensitivity 4P RCCB (ABB, Schneider MG, legrand, Hager make) 63A

Supplying with fitting and fixing 4P 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. C Series (ABB, Schneider MG, legrand, Hager make) 63A

Supply and laying of following size Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988, LT armoured U.G. cable laid in pucca flooring, road crossing, drain crossing as per site requirement and partially in air to connection as approved by the Depts. the control switch, through medium duty G.I. pipe (Tata/ Nezone make or equivalent as approved by the Deptt) bend and socket including excavation and refilling the trench and making good damage done as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) Core - 3 & 1/2 A2XWY A2XFY 70.00 Sq.mm 3&1/2 Core U.G. cable in 50mm dia medium duty G.I. pipe

Supplying with fitting and fixing panel mounting open execution 415V 50Hz 4P MCCB with Microprocessor Release (Ics=Icu, adjustable Over Load and Short Circuit setting, neutral adjustable with earth fault protection Without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 50KA (ABB, Schneider, legrand, L&T, Siemens, C&S make) 100A

EXTERNAL ELECTRIFICATION Supplying, installation, testing and commissioning of the following capacity Copper wound out door type sub-station complete with transformer,HT/LT side fittings and all other following accessories as required complete including payment of ASEB's supervision charge, labour charge, cost of ASEB's materials like metering equipment, CT/PT set etc.(excluding payment of load security),arrangement of charging approval of sub-station from Chief Electrical inspectorate and consisting of the followings: 100KVA,50Hz,11/.433KV oil filled transformer with off circuit tap change

Supplying and erection of H.T. stay set complete (Galvanize with 19mm dia x1.8m long stay rod anchor plate of size 30cm x 30cm x6.4 mm thimble stay clamps tube buckle (19mmx 60c 7/3.15 mm dia G.I stay and strain insulation etc. in cement concrete 1:3:6:(1Cement:3Course sand:6graded stone aggregate 40mm nominal size foundation including excavation and refilling etc. as required and as directed by the department.

Supplying and fitting fixing of galvanised channel of 100 mm x 50 mm x 65 x 2200 mm long complete with clamps ,blots, nuts etc. as required and as directed by the department.

Supplying and erection of 11 KV Pin insulator (Poly) with G.I.pin, blots and nuts coach screw etc. as required and as directed by the department.

Supplying and erection of 11 KV Disc insulator (Poly) 45 KN with hard ware fittings etc. as required and as directed by the department.

Supplying and fixing of 11 KV 400 A Gang operated switch with all accessories complete as required and as directed by the department.

Supplying and fixing of 11 KV 150 A D.O. fuse set complete as required and as directed by the department.

Supplying and fixing of 11 KV 5 KA Lighting arrestor (Poly) set complete as required and as directed by the department.

Supplying and fitting fixing of H.T. danger plate complete as required and as directed by the department.

Supply and laying of following numbers and size of Stranded compact Circular Aluminium Conductor, Conductor Screen with extruded semi conducting compound, XLPE insulated, insulation screening with extruded semi conducting compound in combination with Copper tape (0.3kA for 1se , AL flat strip / round armoured and overall PVC sheathed cable confirming to IS 7098 / (PART-I 1985 with latest amendments, laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 120 cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . 32.7.6.1 --3x70 sqmm 1 core armoured UG cable.

Installation of earth station with 40mm dia and 4.5 mtr. long GI pipe with necessary GI reducing socket 40mmx20mm size locking arrangement with hinged cover plate, funnel, GI nuts, thorough bolts etc.for putting pipe and refitting with necessary enclosure on the top etc. as required complete.

Extra for using salt 5Kg and charcoal 64 Kg. for pipe earth electrode as required.

Supplying and laying with 6 SWG GI earth wire at 0.50 mtr. below ground level or conductor earth electrode including soldering, excavation work and refitting etc.as required complete.

Supplying including installation with required bracket, connection cable, with 2x2.5 sqmm copper FR CABLE, testing and commissioning of the street light/ FLOOD LIGHT on existing pole/ Structure including lamp, driver, ballast as required complete as directed and specified by the deptt.

Construction of 3 phase 11 KV Line on 8.5 m PSC Pole using AAA Raccoon conductor 7/3.81mm with T cross arm average span 70m.

Payment od load security charge to local APDCL Authority.

DEEP TUBE WELL Labour for test boring with 40mm (internal) dia G.I. pipes including keeping surplus of earth and every 2.00 m after first 3.00 m depth and delivering the same in nerest P.W.D. camp in the small tin container (Container, scaffolding, tools etc. will have to be arranged by the contractor at his own cost)

Preparation of site for placement of the drilling rig including excavation of mudpit ,circulation drain, collection chamber etc all complete as directed.

Movement of Rig from the Divisional Head Quarter to the drilling site including cost of P.O.L. all complete as directed.

Transportation of all ancillary equipments,camp materials,welding set, rig accessories etc from the Divisional Head Quarter to the drilling site including cost of POL all complete as directed . b) Beyond 100 m

Transportation of all store materials like pipes, strainer, cone,socket,clamp,bentonite etc from the Divisional Head Quarter to the drilling site including cost of POL all complete as directed . b) Beyond 100

Transportation of air compressor from the Divisional Head Quarter to the drilling site including cost of POL all complete as directed . b) Beyond 100

Construction of temporary accommodation and low cost sanitary facility for drilling staff including cost of camp materials viz. cots, tables, chairs, utensils, dresses, safety helmets etc. and dismantling the accommodation after completion of the work all complete as directed.

Boring in soft soil /normal clay/sandy soil by bit of size either 5.5/8 or 6.7/8 or 7.7/8 inch and collecting sampleor soil at every 3.00 m depth in sample boxes with the distinguishing marks including arranging and carraiage of necessary boring materials------------- etc all complete as directed.

Boring in hard soil / pebble / gravel by bit of size either 5 5/8"or 6 7/8" or 7 7/8" and collecting sample of soil at every 3.0 m depth or wherever there is a change of strata in sample boxes with the distinguishing marks including arranging and carriage of necessary boring materials / tools / bentonite etc. and withdrawing the drill pipe for lowering well assembly etc all complete as directed.

Reboring in soft soil / normal clay / sandy soil by bit of size either 8 1/2" or 9 5/8" or 12" from either 5 5/8" or 6 7/8" or 7 7/8" all complete as directed.

Reboring in hard soil / pebble / gravel by bit of size either 8 1/2" or 9 5/8" or 12" from either 5 5/8" or 6 7/8" or 7 7/8" all complete as directed.

Extraction of drilling pipes / bits against skin friction at the end of each day and after completion of the operation including washing of the bore hole all complete as directed.

Lowering / sinking of well assembly including welding of pipe joints for 200 mm. dia.G.I./ M.S.casing pipe, strainer all complete as directed.

Developing of the D.T.W. with air compressor, Make- Kirloskar / Cumins all complete as directed.

Supplying and packing pea gravel around the periphery of casing including screening, washing etc. all complete as directed.

Cost of MS Pipe including VAT, IT, L.Cess & Contractors profiting etc. 200 mm dia of 8mm thick

E.R.S MS slotted strainer

Supplying, fitting and fixing suction pipes plain/bevel ended, conforming to relevant IS codes of practice including supplying and fitting of accessories, lowering of assembly pipes concentrically in the casing pipes complete as directed. A) G.I. pipe a) TATA / SAIL (Medium)socket should be welded to the pipes. IV) 50 MM Diameter

Supplying including installation, connection as approved by the Deptt., testing and commissioning of CENTRIFUGAL MONOBLOCK PUMP SET complete as directed and specified by the deptt. 3 HP single Phase Centrifugal monoblock pump set (Crompton Greaves/ Aquatic/ CRI/ V-Guard make) 2900 rpm with DOL Starter ( Crompton Greaves/ Control & Switch Gear/ BCH/ L& T / Siemens make).

Supplying including installation, connection as approved by the Deptt., testing and commissioning of SUBMERSIBLE PUMP SET 3 (Three Phase) with steel cable rope and submersible cable complete as directed and specified by the deptt. Three phase Submersible motor pump set (Texmo / Crompton Greaves/ Aquatic/ CRI/ V-Guar suitable for 100 mm bore well and above. 3 HP STAGE 7 to 40 with MCB controlled Submersible motor pump set control panel.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts ( Finolex /RR Kabel /Nicco or Equivalent Make as approved by the Deptt.) in surface flat ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity. With 2 x 4 sq. mm. + earth continuity with 1x2.5 sq. mm. in surface flat 19 mm ISI marked casing 'n' capping system.

Supplying with fitting and fixing panel mounting open execution 35/36KA 415V 50Hz 3P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure) of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 35/36 KA 415V 50 Hz 3P MCCB (ABB(S6) , Schneider, legrand, Siemens, L&T D-shine make) 160A

Supplying fitting and fixing gun metal check valve including necessary threads to pipes. a) 50 mm dia (Heavy type)

Sri Mrinal Saikia