REPAIRS TO COMPOUND WALL FENCING PATH HARD STANDING AREA DRAINAGE ETC AT RANGE HILLS AREA UNDER GE MH AND RH KHADKI

Amount

Demolition of brickwork or stone work/boulder masonary built in cement mortar or cement lime mortar complete all as specified

M&L for precast cement concrete, type C-1, 1:3:6 (20mm graded aggregate) masonary with solid blocks, exc 10cm in width and setting in cement mortar (1:6) complete all as specified and directed.

All as per item No 2 above but except block recovered from demolition complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement morter 1:4 complete all as specified and as directed.

M&L for preparation of new undecorated surface of wall and applying two coats of cement base paint over a coat of primer.

Dismantling fencing, wire mesh any type complete all as specified and directed by Engr-in-Charge

Dismantling wrought iron or mild steel work of any description not otherwise provided for in any position complete all as specified and directed by Engr-in-Charge.

S&F Mild steel for posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or Fe 310-0

M&L for cement concrete in foundation PCC 1:3:6 type C2 using 40mm graded stone aggregate for fencing post etc.

Supply only chain link MS galvanised fencing, any size or type complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

S&F in repairs galvanised 2 strand barbed wire 2.24mm dia of wire and 2mm dia of barbed at 75mm spacing and straining and fixing to any type of strandre nails straining bolts, including securing or tying at crossing with and provn of galvanised MS wire staples or steel pins etc as specified.

All as per item No. 14 here in before but restraining resecuring old fence including making good staples etc only all old wire fit for reuse as directed.

S&F in repair framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165

Dismantling structural steel work including doors, gates but excluding framed truss etc.

M&L for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed.

S&F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of old roof sheet CGI/ PGI Sheet as specified and directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of old Roof sheet CGI/ PGI Sheet complete all as specified and directed.

M&L for preparation of untreated new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of red oxide primer complete all as specified and as directed.

Demolition of cement concrete (un reinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level)

M&L for cement concrete type D-2, 1:4:8 (40mm graded aggregate) 75 mm thick sub base or similar items complete all as specified and directed.

M&L fo Sand filling under floors or in foundation including watering and consolidation

M&L for 80mm thick coloured rubburised, glossy finish machine pressed interlocking pattern paver block any shape and size conforming to IS 15658-2006 of M-40 Grade including all as specified and directed by Engineer-in Charge.

S&F Pre Polished Chequered cement concrete tiles glossy and rubburised finish 30cm x 30cm x 25mm thick, set, jointed and pointed in near cement slurry in floors including 15mm thick screed bed in CM 1:6 under tiles incl all as specified and directed by Engineer-in Charge.

M&L for PCC 1:3:6 type C-1 , 75 mm thick as in plinth protection, Path, floor complete all as specified and directed.

Taking down PVC (SWR) pipes 75 mm dia single sockets and S&F in any length rubber ring joints, laid in trenches or in floor complete all as specified and directed.

M&L for cement concrete type B2 (1:2:4) 40 mm graded aggregate as in surface channels and drains complete all as specified and directed.

Extra for fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc.

Demolition of cement concrete (re inforced) in roof floors, beams, staircase, landings, chajjas, pillars etc and similar suspended works and removing materials from site of work complete all as directed.

M&L for precast cement concrete type B-1 1:2:4 (20mm graded agg) set in CM 1:6 as in cover slabs for manholes etc.

S&F TMT bars 6 to 8mm dia bar, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

Demolition of Stone slabs and tiles of any description or thickness laided bedded and pointed in cement mortar in floors, aprons etc.

M&L Coloured Glazed ceramic tiles engraved textrure type or plain in vertical surface 350x 250x 7 mm/ 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10 mm thick plastering in cm 1:4 all as specified.

M&L for 20mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete fixed over and including backing coat of 10mm thick in CM 1:4 complete all as specified

S&F in repair Pre cast RCC Drain cover of size 600x600 mm thickness 60-70 mm with fine finished with perforated holes 20/25mm and set the same at the site including removing old from site in any position complete all as specified and directed by Engr-in-Charge

JP ENTERPRISES (BID ID -3103735)

shree ram enterprises (BID ID -3117238)

Sunrise Traders (BID ID -3102900)

MAHESH DADAJI BACHHAV (BID ID -3116600)

S P DEVELOPERS (BID ID -3105015)

M/S K.D.MATE (BID ID -3103429)

M/S JAYCONSTRUCTION CO (BID ID -3103169)

greenstone construction (BID ID -3105229)