REPAIR / MAINTENANCE OF ROOF SHEET, CEILING, TILING, HARDSTANDING, INTERLOCKING, PLINTH PAVEMENTS AND OTHER B/R ITEMS AT CH (CC) UNDER GE E/M LUCKNOW

Amount

Dismantling structural steel work including doors, windows & gates but excluding framed trusses etc complete all as specified and directed by Engineer-in-Charge.

Dismantling unframed work timber scantling 40 sqcm and over in section in any position complete all as specified and directed by Engineer-in-Charge.

M&L 2nd class hard wood clean sawn timber fixed in scantling complete all as specified and directed by Engineer-in-Charge.

M&L painting to wood and wood based surface of any description over 10cm width or girth including two coat of synthetic enamel paint over a coat of pink primer including preparation of newly or previously untreated surface complete all as specified and directed by Engineer-in-Charge.

S&F steel work in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St- 240 complete all as specified and directed by Engineer-in-Charge.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy brackets framing (Beams, Tee, angle, channel or flat section) including distance pieces, cleats etc. of Fe 410- W (Gde- E-250) Quality A complete all as specified and directed by Engineer-in-Charge.

M&L for preparing new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (un-reinforced) in ground floors and paving n. exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-Charge.

M&L for cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in coping, padding and bed block, wall through and the like including weathering slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed by Engineer-in-Charge.

Dismantling asbestos cement (corrugated, semi corrugated etc) sheet in roof covering complete all as specified and directed by Engineer-in-Charge.

S&F 6mm thick asbestos cement corrugated or semi corrugated sheets in roofs walls etc fixed with L-type or J-type or cranked hook bolts complete all as specified and directed by Engineer-in-Charge.

S&F 6mm thick asbestos cement two piece serrated ridge for corrugated or semi corrugated sheets fixed with L-type or J- Type or cranked hooks bolts complete all as specified and directed by Engineer-in-Charge.

S&F in 0.50 mm pre-painted galvalume aluminium zinc coating GI based corrugated steel sheeting made to any shape or semi-ciruclar any colour having tensile strength of 550 Mpa as in roof covering/ cladding complete with tapping screw complete all as specified and directed by Engineer-in-Charge.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

Demolition of existing roof treatment of any type complete all as specified and directed by Engineer-in-Charge.

M & L for 15mm thick screed plaster on RCC slab CM 1:4 with using water proofing compound @ 3% by weight of cement. (WPC to be measured and paid separately) complete all as specified and directed by Engineer-in-Charge.

M & L for water proofing treatment on roof surfaces in the following manner:- (a) The surfaces shall be painted with hot bitumen grade 30/40 confirming to IS-73 @ 1.20 kg/sqm over a coat of bituminous primer conforming to IS-3384 @ 0.30 ltr/sqm. (b) supply & lay 3 mm thick APP water proofing membrane reinforced with non woven polyster matt laid using butane torch by torch on application with a side lap of 10 cm & 15 cm end lap weinghing not less than 3.5 kg/sqm complete all as specified and directed by Engineer-in-Charge.

M&L for 230 X 115 X 40 mm thick machine pressed brick tiles with minimum thickness of joint (n.exc.) & are throughly filled with water proof polymer based joint mortar over 20 mm thick CM 1:3 complete all as specified and directed by Engineer-in-Charge.

Preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and directed by Engineer-in-Charge.

All as per item No 19 above but on ceiling.

Preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of cement base paint of any tint/shade complete all as specified and directed by Engineer-in-Charge.

All as per item No 21 above but two coats

Preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of distemper oil emulsion of any tint/shade complete all as specified and directed by Engineer-in-Charge.

All as per item No 23 above but two coats

All as per item No 24 above of one coat but on ceiling.

Preparation of old painted wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

Preparation of old painted surfaces of steel of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment of walls and applying two coats of distemper oil emulsion over a coat of Birla or JK white wall putty average thickness 2mm on old plastered surfaces including prepration complete all as specified and directed by Engineer-in-Charge.

M & L preparation of old brick, stone, concrete, AC or decorated plastered surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L for writing letters or figures (Block, Roman Italic or Indian) n exc 30 cm high with a thick coat of synthetic enamel paint without showing signs of brushes mark complete all as specified and directed by Engineer-in-Charge.

M&L for stops, commas, short lines, dashes, hyphens, brackets etc complete all as specified and directed by Engineer-in-Charge.

M&L applying one coats of Apex ( Asian Paint) / Weather coat (Berger) over old painted surface including preparation of wall surface complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick wall, racking out joints hacking for key scrubbing down with water complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 10 mm thick on brick work / concrete surfaces in cement mortar 1:6 on fair faces finished fair & even complete all as specified and directed by Engineer-in-Charge.

M&L for 15 mm thick rendering in CM 1:4 on fair faces of brick work surface finished even and fair without using extra cement (Note : Integral WPC shall be measured and paid seprately) complete all as specified and directed by Engineer-in-Charge.

Supply only integral WPC of approved quality complete all as specified and directed by Engineer-in-Charge.

M&L rendering 5 mm thick on concrete surfaces in ceiling, in cement and sand mortar 1:3 complete all as specified and directed by Engineer-in-Charge.

M&L for preparing surfaces, plastered or unplastered new surfaces of ceiling and applying three coats white wash complete all as specified and directed by Engineer-in-Charge.

Preparation of newly plastered surfaces and applying two coat of oil bound disemper over one coat of oil base primer all as specified on walls surface including a coat of 3mm wall care putty complete all as specified and directed by Engineer-in-Charge.

M&L applying one coat of plastic emulsion paint interior quality any shade over old painted surface including preparation of wall surface complete all as specified and directed by Engineer-in-Charge.

M&L Preparation of newly plastered or unplastered surfaces of walls by brooming down and priming plastered and other surfaces with cement paint primer (before application of cement base paint) including two coats of cement base paint complete all as specified and directed by Engineer-in-Charge.

M&L for polishing of wooden articles complete all as specified and directed by Engineer-in-Charge.

M&L for complete removal existing treatment and distempering walls with two coats of cement base paint white or tinted over a coat primer on wall sufaces complete all as specified and directed by Engineer-in-Charge. (up to 25 mtr height)

Preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and directed by Engineer-in-Charge. (up to 25 mtr height)

All as per item No 44 above but on ceiling (up to 25 mtr height)

Preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of cement base paint of any tint/shade complete all as specified and directed by Engineer-in-Charge.(up to 25 mtr height)

Preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of distemper oil emulsion of any tint/shade complete all as specified and directed by Engineer-in-Charge. (up to 25 mtr height)

All as per item No 47 above but on ceiling (up to 25 mtr height)

M&L for PCC 1:5:10 type D2 (using 40 mm graded stone agrregate) as in fdns, filling & mass concrete etc complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:2:4 type D2 (using 20 mm graded stone agrregate) as in fdns, filling & mass concrete, for hard standing etc complete all as specified and directed by Engineer-in-Charge.

M&L 75 mm thick cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as plinth protection and the like complete all as specified and directed by Engineer-in-Charge.

M&L for filling joints between two panels with mix of 85/25 bitumen and sand in 1:3 complete all as specified and directed by Engineer-in-Charge.

Demolition of stone slab and tiles of any description or thickness in floors, aprons etc, laid bedded and pointed in cement mortar complete all as specified and directed by Engineer-in-Charge.

M&L 60 mm thick PCC interlocking tiles (rubber laminated finish ) of size and shape as approved , laid dry on sand not less than 40 mm thick, interstices filled in floors/ pathway complete all as specified and directed by Engineer-in-Charge.( Sand cushion shall not be measured and paid seperately)

M&L 60 mm thick PCC intrelocking tiles of size and shape as approved , laid dry on sand not less than 40 mm thick, interstices filled in floors/ pathway complete all as specified and directed by Engineer-in-Charge. (Sand cushion shall not be measured and paid seperately.

M&L chequered cement concrete coloured tiles 20 cm x 20 cm x 20 mm thick with coloured cement and no pigment , set, jointed and pointed in neat cement slurry over 20mm thick screed bed in CM 1:4 as in floors complete all as specified and directed by Engineer-in-Charge. (Note : Screed bed will not be measured and paid separately)

M&L 18-20mm thick machine cut kota stone slab flooring with marble stone strips/ slab/ tiles as per design approved, over and including cement screed bed 15mm thick in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing complete all as specified and directed by Engineer-in-Charge. (Note : Screed bed will not be measured and paid separately)

M&L 18-20mm thick machine cut kota stone slab as in skirting /riser over cement screed bed 10mm thick in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing complete all as specified and directed by Engineer-in-Charge. (Note : Screed bed will not be measured and paid separately)

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

M&L for non skid ceramic (coloured) tiles of 7-8 mm (square or rectangular) area of each tile exceeding 0.18 sqm but n.exc 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over 15mm thick screed CM1:6 complete all as specified and directed by Engineer-in-Charge. (Note : Screed bed will not be measured and paid separately)

M&L for non skid ceramic (coloured) tiles of 7-8 mm (square or rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.16 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over 15mm thick screed CM1:6 complete all as specified and directed by Engineer-in-Charge. (Note : Screed bed will not be measured and paid separately)

M&L vitrified ceramic tiles (dark shade) 10mm thick (square/rectangular) coloured polished tiles, area of each tile n.exc 0.38 sq m in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement and pigment to match over 15 mm thick screeding CM 1:6 complete all as specified and directed by Engineer-in-Charge. (Note : Screed bed will not be measured and paid separately)

M&L for glazed ceramic tiles in vertical surfaces 350 x 250 x 7 mm / 450 x 350 x 7 mm [thick] set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over 10mm thick screed in CM 1:3 complete all as specified and directed by Engineer-in-Charge. (Note : Screed bed will not be measured and paid separately)

M&L coloured / designed as approved wall tiles (exterior grade) 8 to 10 mm thick area of each tile exc 0.09 sqm but n.exc 0.25 sq m in vertical / horizantal surface set and jointed in neat cement slurry and pointed in white/colured cement and pigment to match over 15 mm complete all as specified and directed by Engineer-in-Charge.

M&L for glazed ceramic tiles in vertical surfaces 300x200 x 7 mm [thick] set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over 10mm thick screed in CM 1:3 complete all as specified and directed by Engineer-in-Charge. (Note : Screed bed will not be measured and paid separately)

Divya Jyoti Constructions

PUMA POWER

Ajanta Associates

M/s Vimal Traders

M/S AMARJIT SINGH

NEW BHARAT ENGINEERING AND CONSTRUCTION CO