REPAIR, REPLACEMENT AND MAINTENANCE STREET LIGHT FITTINGS, POLES, CABLE AND CONNECTED ITEMS AT AOP AREA AND ARTILLERY CENTRE UNDER GE NASIK ROAD CAMP.

Supply, fixing, testing and commissioning 68 Watt all in one Solar integrated LED streetlight Made in India consists of Solar Photovoltaic module, battery, control electronics, LED driver, inter-connecting cables and pole mounting piece integrated into the luminaire as a single unit including taking down old fitting complete. A. LUMINAIRE : The luminaire shall have highly efficient mid power white dimmable LEDs minimum 68 W with lumen output of minimum 12000 Lumens, and a typical corelated color temperature of 5700K with CRI >70 and lenses with efficient optics designed for efficient light distribution for secondary roads. The Lumens Output of the Fitting shall be of minimum 12000 Lumens with LM79 report from any NABL Accredited Lab. The Efficacy of Luminaire shall be of Minimum 175 Lumens /Watts. Total Wattage of Luminaire should not be less than 68 W in Order to optimize required PV / Battery Sizing mention in technical specs. Life will be 50,000 burning hours life class. The Successful bidder shall submit LM 79 & LM 80 of the Fitting and LED. B. INTEGRATED CHARGE CONTROLLER: The luminaire shall have a highly efficient, integrated microprocessor based MPPT charge controller with driver mounted on the same board to minimize power loss. This intelligent power management system shall maximize the overall system efficacy to minimum 140 Lumens/Watt with LM79 Report from any NABL accredited lab. The charge controller shall be supplied with a preconfigured dimming profile that shall dim the Luminaires late at night to further increase the autonomy of the system. Dusk to dawn dimming profile should be for first one hour on motion at 100 %, without motion at 25 %, next 4 hours on motion 40 % & Amp; without motion 25 %. Next 6 hours 25 % Fix, rest of night on motion 40 % without motion 25 % Dusk and dawn detection shall be through Voltage generated from the solar panel, and it should be configurable. The Controller Efficiency shall be > than 90% and shall have the following inbuilt protection features:

1. Protection against battery overcharge and deep discharge condition. 2. Protection should be provided against battery and Panel reverse polarity. 3. Over current protection. 4. Protection for reverse flow of current through the PV module(s) should be provided. 5. ON/OFF switch to be provided to prevent discharge of battery during storage /before Installation. The Controller shall meet the relevant IEC codes mentioned. C. SOLAR MODULE : The Solar Cell shall be made of Premium grade mono crystalline silicon Cell. The Solar Module Power shall be minimum 120 WP for better uniformity of light. The Solar module Construction shall be of Low iron tempered glass with low reflection characteristics and with rated IP 65. The Compliance Standards shall be IEC 61215 For Design & Amp; IEC 61730 (Safety Class I & II). The Life Cycle shall be > than 25 Years. The Solar module shall meet the relevant IEC codes mentioned in Table 1. D. BATTERY : The Battery shall be minimum 18 AH~ 25.6 VDC Rechargeable Lithium Ferro Phosphate (LiFePo4) Battery Pack. The Battery Pack should have Inbuilt Battery management system Module with following safety features:- a. accidental short circuit b. over discharge c. over charge d. over temperature. e. Low Temperature

E. HOUSING : i. The luminaire shall have excellent heat dissipation with IP 65 protection and IK08 impact resistance. The front cover is composed of weather resistant, UV stabilized polycarbonate. The front cover is tightly secured with the housing to ensure that the Luminaire has an ingress protection of IP65. The Luminaire shall have a smart self- diagnosis feature with LED indicators for battery charging, deep discharge and Load cut off indication visible from ground in day light. Additionally, It should also be possible to monitor Current and Voltages of Solar panel and Battery for diagnostic purposes through the mobile APP. Test Certificate from any NABL Lab is required. Product Dimension should be 1300x525x145mm. Product Model BRP111LED120/ 757 G2 of Philips or equivalent of Bajaj or CG

Supply, fixing and testing Energy efficient LED Street / Roadway with PDC housing luminaire, high PF, 60W, energy saving and environmental friendly long life versatile pressure die cast aluminium housing, clear toughned glass, IP 66 protection, 240Volts, 120 lumens/Watt, colour temp. 6500K complete all as specified and directed. Make: Cat Part No LHETAVU7PA7J060 of Havells or SLE UL 60W IP66 LXN G1 of Surya or equivalent of Crompton/ Bajaj/Philips

M&L for disconnecting existing street light fittings carefully from bracket/pole, opening the fitting and replacing defective LED outdoor driver suitable for 36-45 Watt street light fitting complete including reconnecting testing and commissioning of fitting after replaceent of driver using required screws, connectors, insulation tape and other minor accesories complete all as specified and directed.

M&L for disconnecting existing street light fittings carefully from bracket/pole, opening the fitting and replacing defective LED outdoor driver suitable for 50-80 Watt street light fitting complete including reconnecting testing and commissioning of fitting after replaceent of driver using required screws, connectors, insulation tape and other minor accesories complete all as specified and directed.

M&L for disconnecting existing street light fittings carefully from bracket/pole, opening the fitting and replacing defective LED outdoor driver suitable for 90-150 Watt street light fitting complete including reconnecting testing and commissioning of fitting after replaceent of driver using required screws, connectors, insulation tape and other minor accesories complete all as specified and directed.

M&L for disconnecting existing street light fittings carefully from bracket/pole, opening the fitting and replacing defective LED outdoor driver suitable for 160-200 Watt street light fitting complete including reconnecting testing and commissioning of fitting after replaceent of driver using required screws, connectors, insulation tape and other minor accesories complete all as specified and directed.

Supply, fixing and testing Energy efficient LED Street / Roadway with PDC housing luminaire, high PF, 70W, energy saving and environmental friendly long life versatile pressure die cast aluminium housing, clear toughned glass, IP 66 protection, 4 kV inbuilt surge protection, 240 Volts, 120 Lumens/Watt, colour temp. 5700K, including taking down old fitting complete all as specified and directed. Make: Cat Part No ENXT P84L WH PO PC SD MT of Bajaj or equivalent of Havells/ Surya/ Crompton/Philips

Supply, fixing, testing and commissioning 48 Watt Hybrid all in one Solar integrated LED street light Made In India consists of Solar Photovoltaic module, battery, control electronics, LED driver, inter-connecting cables and pole mounting piece integrated into the luminaire as a single unit including taking down old fitting comlete all as specified and directed. A. LUMINAIRE : The luminaire shall have highly efficient mid power white dimmable LEDs minimum 48 W with lumen output minimum 8500 Lumens, and a typical corelated color temperature of 5700K with CRI > 70 and lenses with efficient optics designed for efficient light distribution for secondary roads. The Lumens Output of the fitting shall be of minimum 2000 Lumens with LM79 Report from any NABL Accredited Lab. The Efficacy of Luminaire shall be of minimum 175 Lumens /Watts. Total Wattage of Luminaire should not be less than 48 W in Order to optimize required PV / Battery Sizing mention in technical specs. Life will be 50,000 Burning hours life class. The Successful bidder shall submit LM 79 & LM 80 of the Fitting and LED. B. INTEGRATED CHARGE CONTROLLER: The Luminaire shall have a highly efficient, integrated microprocessor based MPPT charge controller with driver mounted on the same board to minimize power loss. This intelligent power management system shall maximize the overall system efficacy to minimum 140 Lumens/Watt with LM79 report from any NABL Accredited lab. The charge controller shall be supplied with a preconfigured dimming profile that shall dim the luminaires late at night to further increase the autonomy of the system. Dusk to Dawn Dimming profile should be for first one hour on motion at 100 %, without motion at 25 % , next 4 hours on motion 40 % & Amp; without motion 25 %, next 6 hours 25 % Fix, rest of night on motion 40 % without motion 25 % Dusk and dawn detection shall be through Voltage generated from the solar panel, and it should be configurable. The Controller Efficiency shall be & morethan 90% and shall have the following inbuilt protection features: