GE ELECT/D-17/2025-26

Amount

Material & labour for excavation in trenches not exceeding 1.5 metre wide & not exceeding 1.5 meter in depth for foundation, laying of cable or pipe (where provided for protection of cable or fixing with poles and stays) and getting out in any type of soil including trimming the sides and forming bottom surfaces to required levels complete all as specified and directed by the Engg-in-Charge.

Material & labour for returning filling in, Including spreading, levelling, Watering and well ramming soil in layers not exceeding 25 cm thick complete all as specified and directed by the Engr-in-Charge.

Material & labour for removing excavated material (ie soil) from site to a distance n. exc 50 mtrs away and depositing where directed at a level n. exc. 1.5 mtr above the starting point complete all as specified and directed by Engr-in-Charge.

Material & labour for river washed and screened, dry sand for filling in trenches below and around underground cables for cushioning of cables etc complete all as specified and directed by Engr-in-Charge. Note - Measurement shall be taken after punning down.

Supply and laying sub class 'B' bricks of old size (approved size locally available) laid along alignment of cable as protection to cable in trenches complete all as specified and directed by Engineer-in-Charge

All as per srl item No 5 here-in-before but using old bricks complete all as specified and directed by Engineer-in-Charge

Material & labour for boring of hole under road/pavement/hard standing or any other situation by mannual means and suitable for passing of GI pipe 40 to 100 mm bore and making good both ends complete all as specified and directed by Engr-in-Charge.

Material & labour in replacement for GI tubes of size 80 mm dia (light grade) with necessary accessories/ fittings for cable protections/pole for crossing of culverts/nallah complete all as specified and directed by Engr-in-Charge.

Material & labour in replacement for GI tubes of size 50 mm dia (light grade) with necessary accessories/ fittings for cable protections/pole for crossing of culverts/nallah complete all as specified and directed by Engr-in-Charge.

Supply, installation, testing and commissioning of outdoor type stainless steel (SS-316) cubical enclosure compartmentalized exterior and interior mirror type brushed suitable for highly corrosive environment, high creep resistance, better mechanical properties like ductility, yield strength, hardness etc.The enclosure shall be made of 2 mm thick SS-316 sheet. The fixing of double doors shall be on SS hinges with anti-theft provision (the door can’t be removed from enclosure without cutting enclosure). All fabrication/welding shall be done with TIG/MIG or as approved by Engineer in charge suitable for SS 316. Sliding handle and locking arrangement front and rear both side . Enclosure shall be suitable for AC supply system 415 volts 3 phase, 4 wire, 50 HZ AC supply system having bus bar chamber with insulated Aluminium bus bar installed on proceline/ SMC insulator of rating not less than 1.5 times of incoming/ outgoing ACB/MCCBs . IP-55 class protection and mounted on channel 75 mm welded with panel of SS 316 with 04 Nos foundation bolt of size not less than 20 mm dia and 300 mm long. The enclosure shall have provision of cable alley. Cable entry from bottom side including internal wiring with PVC insulated solid, copper conductor FRLS cable, IS-694 marked, 1100 volts grade of appropriate size (but not less than 2.5 sqmm).

INCOMING:- (i) MCCB 4 pole, 630 Amps, 50 Hz, 415 Volts, 50 KA Adjustable Thermal and Adjustable Magnetic setting- 1 Nos (ii) Voltmeter digital - 01 No (iii) Ammeter digital type - 01 No (iv) CT ratio 600/5 Amp class-1 ISI marked - 01 Set of three (v) Indicating LED lamp one set of three OUTGOINGS:- (i) MCCB 4 pole, 250 Amps, 50 Hz, 415 Volts, 36 KA Adjustable Thermal and Adjustable Magnetic setting - 02 Nos (ii) MCCB 4 pole, 200 Amps, 50 Hz, 415 Volts, 36 KA Adjustable Thermo and Fixed Magnetic setting - 01 No (iii) MCCB 4 pole, 100 Amps, 50 Hz, 415 Volts, 25 KA Adjustable Thermo and Fixed Magnetic setting - 03 No

All as item no-10.0 above (here in before) but with the specifications as followings:- INCOMING:- (i) MCCB 4 pole, 250 Amps, 50 Hz, 415 Volts, 36 KA Adjustable Thermal and Adjustable Magnetic setting- 1 Nos (ii) Voltmeter digital type - 01 No (iii) Ammeter digital type - 01 No (iv) CT ratio 250/5 Amp class-1 ISI marked - 01 Set of three (v) Indicating LED lamp one set of three OUTGOINGS:- (i) MCCB 4 pole,125 Amps, 50 Hz, 415 Volts, 25 KA Adjustable Thermal and Adjustable Magnetic setting- 1 Nos (ii) MCCB 4 pole,100 Amps, 50 Hz, 415 Volts, 25 KA Adjustable Thermal and Adjustable Magnetic setting- 2 Nos (iii) MCCB 4 pole, 63 Amps, 50 Hz, 415 Volts, 25 KA Adjustable Thermal and Adjustable Magnetic setting- 3 Nos (iv) Space free for one compartment.

All as item no-10.00 above (here in before) but with the specifications as followings:- INCOMING:- (i) MCCB 4 pole, 250 Amps, 50 Hz, 415 Volts, 36 KA Adjustable Thermal and Adjustable Magnetic setting- 1 Nos (ii) Voltmeter digital type - 01 No (iii) Ammeter digital type - 01 No (iv) CT ratio 250/5 Amp class-1 ISI marked - 01 Set of three (v) Indicating LED lamp one set of three OUTGOINGS:- (i) MCCB 4 pole, 63 Amps, 50 Hz, 415 Volts, 25 KA Adjustable Thermal and Adjustable Magnetic setting- 7 Nos (ii) Space free for one compartment.

Note for item No- 10 to 12:- (i) All incoming and outgoing feeder shall be connected by cable through suitable size glands & thimbles. (ii) The various feeders shall be indicated by 50 mm size letters in synthetic enamel paint/ Flourcent refelctive lettring . (iii) All MCCB should be connected to Bus bar directly through expended links (iv) All MCCB with adjustable protection for over load and short circuit and conforming to IEC60947/IS 13947/Pt. II/1993 (Latest Version). The MCCB should have Ics=100% Icu. The MCCBs shall have spreader links and barriers as standard feature of manufacture. (iv) Costruction of Foundation & taking out of the old connected cables and reconnection of the same with new thimbles, gland of suitable size are deemed to the above quoted rate.

Supplying, laying, jointing testing and connecting in replacement XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with multistranded aluminum conductors, IS 7098 marked, suitable for LT 1100 Volt system, laid in trenches fixed to pole, including jointing & testing complete all as specified and directed of following sizes:- Note :- Excavation, earth work ,cable protection , sand fillings , cable joint shall be measured and paid separately under respective items of schedule.

240 Sqmm 3.5 Core

150 Sqmm 3.5 core

70 Sqmm 3.5 core

50 Sqmm 3.5 core

35 Sqmm 3.5 core

25 Sqmm 4 core

Material & labour for earthing for poles and other machinery/eqpt using GI strip as earth lead and MS galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate is not less than 1.5 mtr below normal ground level connected to galvanized iron wire of 4mm with GI pipe, nuts, bolts and washers complete upto and including test point made out of 40x3mm GI flat, PCC pit of required size in PCC 1:2:4 type B1 and RCC cover with frame, charcoal, common salt15cm at round the earth plate watering pipe 20mm med grade/galvanized and 40mm dia GI pipe light grade for GI strip protected steel with funnel complete all as specified and directed by Engr-in-charge as shown in electric plate No 3 of MES SSR Part-I (1991).

Supply & fixing of KIOSK Box weather proof made up of one piece mounted on SMC base and door pole mounted hinged door of size 333 x233x 120 mm outside and 300x200x105mm inside dimension comprising of aluminum bus bar 4 strips for 3 phase and neutral 63 Amp and 6 Amp fuse grip with base for controlling the steet light fitting and FL clamps 30x4mm with necessary MS nuts bolts and washers and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel surface and including embassing/painting of Danger notice of size not less than 10cmx7.5cm with letters, figures and conventional skull and bones in signal red colour on front face of KIOSK box body complete all as specified and directed by Engr-in-charge.

Supply & fixing in replacement of Energy saving, environmental friendly, long life, LED street light made up of pressure dia cast aluminium housing with high efficient lighting source with toughened glass having IP66 protection LED street light of capacity 70 Watt complete all as specified and directed by Engr-in-charge.

Supply, drawing, connecting and testing in replacement 3 core, 1.5 Sqmm PVC insulated and PVC round sheathed copper conductor (flexible ) industurial cable, 1100 Volts conforming to IS 694 in steel tubular poles from KIOSK box to street light fitting including providing suitable copper lugs where required complete all as specified and directed by Engr-in-charge.

Supply, Jointing, Testing and commissioning of Cable jointing kit for 1100 Volts grade cable for Straight Through heat shrink type joint complete with jointing material and accessories suitable for 1100 Volts PVC/XLPE armoured aluminium conductor cable of size 25 to 50 sqmm x 3.5/4Core complete all as specified and directed by the Engg-in-Charge.

Platform:- Material & labour for Brick Masonry (Using sub class 'B' Brick) platform of size 3.0 mx3.0 mx1 m height, built in CM 1:4 complete with excavation & earth work, PCC 1:4:8 type D-2 in foundation 150 mm thick, 15 mm thick rendering in CM 1:6 on sides and top of the brick work upto 150 mm below ground level, supply and fixing of 02 Nos MS Channels of suitable size for balancing of Transformer embedded in PCC 1:2:4 type B-1 up to 100 mm Thick RCC 1:3:6 with 10 mm steel bar includding 20 mm graded aggregate , including provn of stair case on one side complete all as specified and directed by Engr-in-charge.

Fencing :- Material & labour for perimeter fencing of size 9mx6mx2m having MS work of angle iron for post and struts for fencing around the transformer plinth/substation/LT panels etc incl drilling holes in flat iron fillet for securing wire mess by welding to angle iron frame and framed work as in door/gate of angle iron and wire mesh. Door to be fixed by 03 nos 100 mm long hinges and one sliding door bolt of 300 mm long for locking arrangement. Details are as follows:- (a) Angle iron post to post distance maintained not more than 02 mtr, size of angle shall be 40x40x5 mm. Angle Iron shall be embedded in natural ground not less than 0.60m deep. (b) MS wire 75x75mm mesh 3.15 mm dia, 2mtr height and shall be fixed to post with flat iron 32x6 mm fillet with two coats of synthetic enamel paint over a coat of red oxide primer. (c) Cement concrete type D-2, 1:4:8 using grade crushed stone aggregate for mass concrete/ foundation. (d) Brickwork with subclass 'B ' bricks, straights or curved on plane exc 6m mean radius ,built in CM 1:6 complete for toe wall along the perimeter fencing. The toe wall shall be one brick thick (23 cm), 30cm high (15 cm above GL and 15 cm below GL) on 75 mm thick PCC lean concrete. (e) The exposed surfaces of brickwork shall be rendered 15mm thick in CM (1:4) finished fair and even without using extra cement. (f) The steel gate shall be of size 1.00m x2.00 m fabricated from angle iron 40x40x5 mm frame and 12x12 mm square guard bars. (g) All the exposed surfaces of steel shall be painted with two coats of Synthetic enamel paint over one coat of Red Oxide Primer. (h) Necessary excavation and earthwork shall be included in the quoted rate.

Note : contractor should procure and provide 50 % of the material as listed above within 15 days of the placing of work order and shall be verified by the Engr-in-charge

mayur enterprises (BID ID -3333694)

DS CONSTRUCTION (BID ID -3333210)

M/s JAIMAA ASSOCIATES (BID ID -3333921)

M P TYAGI ENGINEERS AND CONTRACTORS (BID ID -3333863)

MV Engineers And Contractors (BID ID -3326099)

Rajindera Enterprises (BID ID -3328580)

Vijay Electricals (BID ID -3333668)