SPL REPAIR TO BLDG NO.T-10(BLT LINE), T-890 (DINNING HALL), T-15 (OR COOK HOUSE), T-755 (LRW LIVING) AND T-769 (JCOS SINGLE LIVING) AND PROVN OF HARDSTANDING ALONGWITH SHED UNDER GE (ARMY) SURATGARH AT SURATGARH MIL STN

Amount

Taking down cement or cement lime plaster wall and ceiling including in patches, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed

Demolition of cement concrete (unreinforced) in ground floor and pavings not exc 15 cm thick (below or above ground level) including floor tiles of any description complete all as specified & as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Dismantling of stone slabs in roofs, suspended floors, chajjas, landings, etc., any description, any thickness, jointed in any mortar, complete all as specified & as directed.

Taking down chowkat or frame with shutters (including fittings & fixtures) area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed.

Taking down chowkat or frame with shutters (including fittings & fixtures) area not exc 1.5 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed.

Taking down old rusted & damaged steel windows of any description and of any type & size with guard bars / grill including cutting holes for hold fasts & making good the disturbed portion complete all as specified & as directed.

Taking down old rusted & damaged steel ventilators of any description and of any type & size without guard bars / grill including cutting holes for hold fasts & making good the disturbed portion complete all as specified & as directed.

Dismantling of cast iron or PVC , jointed in cement mortar pipes up to 100 mm bore in any position complete all as specified and as directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer-in-charge.

Dismantling of timber scantling 40 sqcm and over in section unframed work and in any position complete all as specified and directed by Engineer-in-Charge.

Dismantling timber scantling under 40 sq cm as in fillets , posts, rafters, purlins etc. complete all as specified and as directed.

Demolition of existing false ceiling complete incuding fillets, grid complete all as specified and as directed.

Dismantling Asbestos cement, Corrugated sheets in roof covering including ridges complete all as specified and as directed.

Dismantling carefully and taking up or down 15mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

Dismantling carefully and taking up or down 20mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

M&L for brick work with old size fly Ash bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified and as directed.

All as per serial item No 15.00 here-in-before but except bricks. Note : Old serviceable burnt clay / fly ash bricks retrieved from serial item No. 3.00 here-in-before shall be used under this item.

M&L for brick work with old size fly Ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

M&L for steel work as in square / tubular trusses, purlins, post including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St.-240 including painted with one shop coat of zinc chromate primer paint including preparation of surface at contractor workshop before fabrication complete all as specified and directed by Engineer-in-charge.

S&F Mild steel bolts.exc. 5 cm length not exc. 10 cm length (machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends, each screwed end to be fittied with washers and one hexagonal or square nut 11 to 15 mm neck dia complete all as specified and as directed by engineer-in-charge.

S&F rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails , fixed with angle cleats or other connecting plates, gusset plates, etc conforming to Fe-290 (Gde E- 165), complete all as specified & directed by Engineer-in-charge.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment etc conforming to Fe-290 (Gde E- 165, complete all as specified & directed by Engineer-in-charge.

S&F for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-charge. Note:- Roof sheet shall be required and fixed in arch/curve/angular shape as per user requirement/as per directed by Engr-in-charge and nothing shall be paid extra on this account.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges, hips, valley gutter, drip and straight flashing (length and girth as refixed), fixed with self tapping screws complete all as specified and as directed.

S&F Composite cement designer ceiling board 4 mm thick in ( 595 mmX595 mm ) pannel (Make-everest ramco or eql.) designer ceiling pre finished conforming to IS 14862 type B cateogory three incl powder coated GI frame , grid work,hold fast,suspended with suspender along with holding down bolt complete . (Note: Ceiling board shall confirming to IS-14862 ,shall be fire resistant , Moisture resistant and ceiling shall be suspended with suspenter and adjuster .) complete all as specified and as directed

M&L cement concrete (1:4:8) type D2 using 40mm graded stone aggregate as in foudation, filling, sub base and mass concrete Complete all as specified and as directed.

M&L for providing 75 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight Complete all as specified and as directed.

M& L for rendering 10 mm thick on fair faces of brick or concrete surfaces in cement mortar 1:6,even and smooth w/o using extra cement Complete all as specified and as directed.

M&L for 15 mm thick rendering in two coat (10+5 mm) on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1:4. (Note: Plaster shall be carried out in patches and contractor shall have no claim for any height and scaffolding what so ever is the location)

M&L for 40-50mm thick sand stone slab not exc 2mtr in length, punched dressed self faced set and pointed in CM 1:4 as in sun-shades, chajjas, shelves, cills landings, cover stone including cutting chasing complete all as specified and as directed

M&L Granite 20 mm thick of any type work table rubbed and polised in steps,jambs,pillars,window cill, cooking plateforms and like in cement mortar 1:4 including pointing cement mortar 1:2 using marble dust with admixure of pigments to match with shade of granite over 15 mm thick screed bed of CM 1:6 complete.

Machine cut kota stone slab 18 - 20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab incl.rubbing and polishing laid over 15 mm thick cement screed base in CM 1:6. The joints shall be 20mm wide filled with cast in situ tarrazo with white marble chips of size up to 6mm complete all as specified and as directed. (Note:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same)

All as per item No 33 above but in skirtings laid over 10mm thick backing layer in CM 1:4

M&L Non skid Ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors on 15mm thick screeding in CM 1:6. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed Note:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same

M&L for 10 mm thick Vitrified coloured Double charged tiles of size n.exc. 0.36 Sqm as in floors over 15 mm hick screed in CM 1:6 jointed in neat cement slurrry and pointed in white cement slurry to match the shade of existing surfaces , colour as approved by GE complete all as specified and as directed (Note:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same)

ditto as per Serial item above but with 10 mm thick in CM 1:4 as on vertical surface.

Glazed ceremic tiles white 600X300mmX7mm thick coloured,set and jointed in neat cement slurry and pointed in white cement or coloured to match colour matching with floor tiles as on vertical surfaces laid over 10mm thick cement screed in 1:4 complete all as specified and as directed. (Note:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same)

Supply & Laying CPVC SWR 20 mm outer dia pipe and fittings including cpvc brass fiitings laid in trench or fixed in walls or laid in floors complete all as specified and as directed by Engineer-In-Charge

Supply & Laying CPVC SWR 25 mm outer dia pipe and fittings including cpvc brass fiitings laid in trench or fixed in walls or laid in floors complete all as specified and as directed by Engineer-In-Charge

Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 1000 Litre capacity Rotational moulded tanks four layer (cylindrical vertical with closed top) , hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed. MAKE: Sintex Pure /Ashirwad Weatherguard /Asteral Cleo or other Technocommercial as mentioned in Appx 'A' here in after.

S&F Factory sqm de single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 125x65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately) complete and making good existing disturbed surface with CM 1:3 complete.

S& F for 35 mm Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S&F factory made Powder coated casement aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall not be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285,Aluminium handles, tower bolts , fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. Make :- FENESTA/NALCO/AIS or equivalent technocommercial make as specified in Appendix 'A'. Note:- Minimum Weight of Frame shall be 1.139 Kg/RM and Minimum Weight of Shutters shall Be 1.039 Kg/Rm complete.

S& F for 30 mm Factory made single extruded WPC (Wood Polymer Composite) GLAZED door shutter of 30 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer, calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S& F for 30 mm Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, cooler stand 12mm sq guard bar, framework of water tanks and similar works of quality Fe 290 (Gde E-165) etc complete all as specified and directed by Engineer-in-charge.

S&F 3 mm Sheeet glas ordinary quality and glazing with oil putty in square n exc. 0.5 sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

M&L Galvanised Mild steel wire cloth 0.56 mm nominal dia of wire anfd averqagae width of aperature 1.18mm and fixed with tinned tracks, or galvanised wire spaples complete all as specified and directed

Supply and fixing of 100 mm But hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed

S&F steel locking bolts with mils steel electrogalvanised plate and bright bolt ont less than 10 mm dia and 100 mm size, complete all as specified and directed

S&F for 150mm size aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and directed

S&F for 150mm size aluminium anodised handle of febricated type and fixed complete all as specified and directed

S&F mild steel barrel tower bolt ,stove enamelled black with bright bolt of 200 mm complete all as specified and directed

S&F 250 mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed

S&F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed

S&F mild steel pressed handles oval type stove enamelled black of 150mm complete all as specified and directed

S&F as in repair 25 mm thick Stainless Steel pipe Curtain Rod fixed with 2 nos steel brackets and Steel knobs at both ends as per site requirement including making good disturbed portion with 1:3 cement plaster and finshing treatment of existing wall quality complete all as specified and as directed by Engineer-In-Charge.

S&F ball valve high pressure of PTMT with epoxy coated almn rod and high density plastic ball screwed for iron pipe and fixed fixed in repair.of 20mm complete all as specified and directed

S&F as in repair Viterous china wash down water closet pan pan (pedestal pattern ), white (excluding flushing cistern , flush pipe complete all as specified and directed

S&F Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated hinging device, complete all as specified and directed

S&F as in repair wash hand basin of size 450x450x160 bowl type of make Parryware C0477 or equivalent in JOHNSON, HINDWARE fixed with bottel trap 9" vertical type and full threaded CP waste coupling 32 mm dia 130 mm long complete fixed complete all as specified and directed

S&F as in repair PVC low level flushing cistern 10 litres capacity, white, with all fitting and fixtures including brackets and 32 mm bore PVC flush pipe, complete all as specified and directed

S&F as in repair bib taps long body cast copper alloy chromium plated fancy type 15mm bore with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed . Note :- Tap shoould have minimum weight as per IS 8931 of Make :- Johnson/Somany/Hindware or equivalent technocommercial make as specified in Appendix 'A'.

S&F as in repair pillar taps cast copper alloy with capstan head, chromium plated, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe and fixed. Note :- Tap shoould have minimum weight as per IS 8931 of Make :Johnson/Somany/Hindware or equivalent technocommercial make as specified in Appendix 'A'.

S&F as in repair Brass chromium plated wall mixer 3-in one telephonic for mixing hot and cold water screwed down for iron pipe 15 mm bore with hand shower abs body and 1 m long flexible tube complete all as specified and as directed by Engineer-in-Charge. Make ( Somany/hindware/Johnson) or equivalent technocommercial make as specified in Appendix 'A'.

S&F as in repair angle valves, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down high pressure, screwed both ends for 15 mm bore dia iron pipe or for union, ISI marked, supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge. Note :- Tap shoould have minimum weight as per IS 8931 of .Make ( Somany/hindware/Johnson) or equivalent technocommercial make as specified in Appendix 'A'.

S&F as in repairs 150 mm Overhead square ABS Shower Full Chrome with Brass Arm 225 mm & Flange complete all as specified and directed. CAT Part No:- BOS-90S of Parayag,hindware,somany,jaqua or equivalent technocommercial make as specified in Appendix 'A'.

S&F as in repair towel rail Chromium plated brass complete all as specified and directed . CAT Part No. BA-01 of Parayag,hindware,somany,jaqua or equivalent technocommercial make as specified in Appendix 'A'.

S & F as in repair glass corner of size 300mmx300mm with 5.5 mm thick glass and steelness steel clip and steelness steel railing allround the shelf complete all as specified and directed by engineer in charge .

S&F as in repair CP soap dish, fancy type fixed to wall with CP brass screws , complete all as specified and as directed by Engineer-in-Charge.

S&F as in repair Spray jet, brass chromium plated, with and including 1.5 metre long PVC flexible reinforced pipe for EWC, for bore dia of pipe 15mm,complete all as specified and as directed by Engineer-in-Charge. Make ( Somany/hindware/Johnson) or equivalent technocommercial make as specified in Appendix 'A'.

S&F 32/40 mm dia PVC waste pipe for WHB/sink complete all as specified .(Min weight 45 to 60 gms .

S&F as in repair pvc connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed

S&F 110mm bore PVC (SWR) pipes single socketed in any length jointed with adhesive fixed to walls fixed with and including requisite Number of clamps made out of flat iron 25x4mm complete all as specified and as directed by Engineer-in-charge.

S&F 75mm bore PVC (SWR) pipes single socketed in any length jointed with adhesive fixed to walls fixed with and including requisite Number of clamps made out of flat iron 25x4mm complete all as specified and as directed by Engineer-in-charge.

S&F 110mm bore PVC (SWR) junction,single (single T) equal or unequal complete all as specified and directed by Engineer-in-Charge"

S&F 110 mm bore PVC (SWR) bends any radius jointed with adhesive with oval access door complete all as specified and as directed by Engineer-in-charge.

S&F 75 mm bore PVC (SWR) bends any radius jointed with adhesive with oval access door complete all as specified and as directed by Engineer-in-charge.

S&F 110mm bore PVC (SWR) reducers 110mm to 75mm complete all as specified and directed by Engineer-in-Charge

S&F 75mm bore PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge

M & L for preparation of newly plastered surfaces of wall & applying two coats of Interior emulsion paint by Roller or Air Spray over 1 mm thick wall care putty (Multipurpose mixer shall be used for uniform and proper mixing of putty) complete all as specified and as directed by Engineer-in- charge. Make : Tractor Emulsion (Asian Paint), Easy Clean (Berger Paint), Promise Inerior (Dulux Akzonobel or other Technocommercial as mentioned in Appx 'A' here in after.

Material & Labour of preparation newly plastered and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed by Engineer-in-Charge. Make :- Apex Ultima (Asian Paint), Weather Coat anti dust ( Berger Paint ), Excel No Dust ( Nerolac or other Technocommercial as mentioned in Appx 'A' here in after.

M&L Complete removal of existing treatment and preparation of old decorated (platered or unplastered) of wall by Vaccume based sanding machine, removal of nails etc including filling of cracks and applying two coats of Interior emulsion paint by Roller or Air Spray incl over a layer of 1 mm or as required ( Multipurpose mixer shall be used for uniform and proper mixing of putty) of wall care putty, on plastered surfaces,prepara-tory to distempering complete all as specified & directed by Engineer -in-charge. Make : Tractor Emulsion (Asian Paint), Easy Clean (Berger Paint), Promise Inerior (Dulux Akzonobel or other Technocommercial as mentioned in Appx 'A' here in after.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified & as directed.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified & as directed.

Excavation in post holes (or similar holes) each n.exc 0.5 Cum getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25 cm thick, watering and removing surplus soil to a distance n.exc 50 mtr and making good surfaces in soft/loose soil.

M&L for PCC (1:2:4) tye B2 (using 40m graded stone aggregate) as in foundation of posts and struts complete all as specified and as directed by Engineer-in-Charge

Surface excavation averaging 15 cm deep and not exceeding 30 cm deep and getting out in soft and loose soil.

M&L for Hard core of broken stone or boulders of gauze not exc 63 mm deposited spread and levelled in layers not exc 15 cm thick watered and rammed to a true surface

M&L for 100 mm thick cement concrete type D2, (1:4:8) using 40mm stone aggregate as in sub base.

M&L for Machine pressed precast rubbersed conctete interlocking paver block ruber moulded and shape and size approved by GE and confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade with grey cement and no pigment complete all as specified and directed by EIC.

M&L for 25 mm thick Sand filling under floors or in foundations including watering and consolidation.

M & L Cement Concrete type B1 , 1:2:4 mix (20mm graded crushed stone aggregate ) as in bedding , benching of manholes , copings, roof kerbs and surface channel etc. complete all as specified

Excavating in trenches n exc 1.5 m wide and n exc 1.5m in depth, for foundation, etc and getting out in soft/loose soil complete all as secified and directed.

M&L for PCC (1:4:8) type D-2 using 40mm graded stone agg as in fdns filling & mass concrete complete all as secified and directed.

M&L brick work with sub class 'B' brick straight or curved on plan exc. 6 m mean redius built in C:M 1:6 complete all as secified and directed.

Removing excavated soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point all as directed and specified by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in ayers not exc 25 cm complete all as specified.

M&L for preparation of newly plastered surface of walls & applying two coats of cement base paint over a coat of primer of approved shade/tint complete all as specified and directed by Engineer-in-Charge.

Taking down carefully or drawn out from conduit, existing copper / aluminium point wiring for light, fan, bell, socket, power point etc complete including fixture and fittings such as switches, sockets, ceiling rose, pendent holder, light fittings, top sheet covers, fan regulators, MCB, DB, lamp, earth plug etc (excluding MS sunken boxes) and making good the disturbed surfaces of wall/ceiling complete all as specified and as directed by Engineer-in-charge.

All as per serial item No. 104 here-in-before but for One 3 pin 5 Amp socket outlet one light point controlled by one switch on the same board with other switches.

All as per serial item No. 104 here-in-before but for One 3 pin 5 Amp socket outlet one light point controlled by one switch on independent board.

All as per Srl item No. 104 above, but wiring with cable of cross sectional area 4 Sqmm (nominal area) multi-stranded copper conductor FRLSH, PVC sheathed cable 1100 Volts shade for one switch socket combination 3 pin, 15/16 Amps on independent board including 4 Sqmm PVC insulated multistranded unsheathed copper conductor wire as earth continuity to common earth dolly.

S&F Modular switch piano 6 Amps single pole, one way, 01 Module complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F Modular switch piano 16 Amps single pole,one way, 01 Module complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F Modular socket 2 / 3 pin, 6 Amps, 230 volts, combined 2 Module complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F Modular socket 06/ 16A, 6 pin,2 module, complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F Modular electronic fan regulator suitable for ceiling fan 2 Module, 1200mm / 1400mm sweep, socket size, rotary type complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F as in repair sheet metal plug & socket DB, SP, with a two pin and earth plug with socket, 230 Volts with & including one MCB SP ‘C’ Curve 10 kA, 20 Amps complete all as specified and directed by Engineer-in-charge.

S&F Lamp holder, insulated body with back plate etc complete all as specified and as directed by Engineer-in-Charge.

S&F ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified and directed by Engineer-in-charge.

Supply and fixing LED lamp minimum 3 star rated 10W LED B-22 base complete all as specified and directed by Engr-in-Charge with following specifications (a) Lumen system efficacy of lamp should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 45°C (d) Power factor : Minimum 0.90 (e) CRI : Morethan 80 Make : Havells Cat No LHLDDEBNL5R10/WIPRO/PHILLIPS/CROMPTON or equivalent Technocommercial cat part of Make as specified in Appendix "A".

S&F Energy saving 9/10 watt environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head edge-lit LED luminaire comprising of high brightness LEDs, IP 65 protection fixed on wall complete all as specified and as directed by Engineer-in-charge. Make : Crompton Cat No CIS-306-10-57-SL-DP-NBK/WIPRO/HAVELLS or equivalent Technocommercial cat part of Make as specified in Appendix "A".

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. Make : Havells Cat No LHEBAEP5IW1W036/WIPRO/CROMPTON or equivalent Technocommercial cat part of Make as specified in Appendix "A".

S&F Energy efficient decorative ultra slim, prewired, lumiline 20 watt LED light fitting (Day cool light), batten type with drive & polycarbonate housing including tube rod and all accessories prewired fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge. Make : Havells Cat Part No.:- LHEXAZP7PN1W020/Crompton Cat Part CCS-103-20-65-SL-DP-NWH/Wipro Cat Part D532065 or equivalent cat part of Make as specified in Appendix "A".

S&F Energy efficient decorative ultra slim, prewired, lumiline 10 watt LED light fitting (Day cool light), batten type with drive & polycarbonate housing including tube rod and all accessories prewired fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge. Make : Havells Cat Part No.:- LHEXAZP7PN1W010/Crompton Cat Part CCS-103-10-65-SL-DP-NWH/Wipro Cat Part D531065 or equivalent cat part of Make as specified in Appendix "A".

Supply, fixing and testing as in repair LED Street / Security light fitting of 35 Watt, 5700K - 6500 K (including LED drive and internally prewired) complete with body robust, corrosion resistant, superior finish and without any cracks or through holes, made in a single piece by high pressure die cast aluminum alloy. The luminaries shall be monolithic construction totally enclosed dust and water proof with IP -65 / 66 protection as per IS - 10322-1982(Part -I) with latest amendments and input voltage range 140 - 300 V, AC, frequency 50 - 60 Hz ,P.F should be more than 0.9 with Total Harmonic Distortion THD(I) less than 15% ,cool white colour and lamp starting time should not be more than 10 second including 10 KV surge protection in built or external. Driver should be constant current constant voltage driver. Driver should have high voltage withstanding capacity upto 300 V, AC. Driver should also have double phase protection, no load , open circuit and short circuit protection .LED light fitting should be suitable for ambient temperature from -10 degree Centigrade to 50 degree Centigrade and humidity level 10% to 90 % RH. Covers should be polycarbonate/toughened glass to ensure minimum IP 65 degree protection. Cover should not degrade due to heating and ageing. The efficiency of LED luminaries system shall be more than 100 lumens per watt and must be certified by the LM-79 test report and including connection for street light from pole box with 1.5 Sqmm, 3 core PVC insulated stranded copper conductor FRLSH cable, 1100 Volts grade ISI marked including addition / alteration in bracket (if required) for fixing light fitting complete all as specified and directed by Engineer-in- charge .Make : Crompton /WIPRO/HAVELLS or equivalent Technocommercial cat part of Make as specified in Appendix "A".

Notes for srl Item No 121 :- (a) Tenderer shall submit test report of LED street light fitting from Government accredited test laboratory for LM - 79 and LM - 80 . (b) Contractor has to furnish a replacement warranty of 05 years for LED light fittings complete including lamps from the date of completion of CA. Contractor shall obtain warranty from the manufacturer of product on their letter head and submit the same to deparment alonwith his letter head. The product will be replaced free of cost in the following case :- (i) Manfacturing defects (ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (c) All LED light/luminare must meet the provision laid down in IS - 16101 , 16102 Part -I/II ,16103 Part -I , 16104 ,16105 ,16106 , 16108/2012 and 15885 Part -II / Section 13. (d) Scope of work shall include supply and fixing street light fittings on street light bracket fixed on poles, If street light fitting requires to fixed on existing street light bracket and any addition alterration required in bracket for fixing street light, In that case cost of additional / alteration is included in the unit rate of this item, which also includes needful T & P and required accessories such as 1.5 sqmm, 3 core PVC insulated stranded copper conductor cable for connection from pole box to light fitting etc complete including making connection, testing etc complete .No extra payment is admissible on this account. (e) Light fittings shall be provided with 10 KV surge protection as mentioned in description of item. If 10 KV surge protection is not provided in light fitting for which cat part is mentioned in BOQ. Contractor has to provide light fitting with 10 KV surge protection without any extra cost to department. (f) Contractor shall write CA No on street light fitting with synthetic enamel paint which should be visible from ground level. Cost of the same is included in the unit rate of this item nothing shall be extra paid on this account.

S&F as in repair flush mounting factory made SPN DB 8 way, 240 Volt, Single door, IP-43 protection, IK-09 with metal door with 100 Amps copper bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by Engineer-in-charge. Make :Legrand/Havells/L&T or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F as in repair flush mounting factory made SPN DB 12 way, 240 Volt, Single door, IP-43 protection, IK-09 with metal door with 100 Amps copper bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by Engineer-in-charge. Make :Legrand/Havells/L&T or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F as in repair flush mounting factory made VTPN DB 4 way, 415 Volt, Double door, IP-43 protection, IK-09 with metal door with 160 Amps copper bus bar, with 02 neutral bar, 02 earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by Engineer-in-charge.Make :Legrand/Havells/L&T or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F MCB 6 to 32 Amps, Single Pole 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge. Make :Legrand/Havells/L&T or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F as in repair MCB 40-63 Amps, Single Pole & neutral 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge. Make :Legrand/Havells/L&T or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F as in repair MCB 100 Amps, four pole , 415 Volts, 25 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge. Make :Legrand/Havells/L&T or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F as in repair street light bracket made out of 32mm dia GI pipe light grade 1.20m long , bent to shape at 120 degree angle from vertical fixed along pole with and dirlling holes including required number of clamp made out of Flat iron 25mm x 6mm with nuts, bolts ,washers etc. duly painted with two coats of aluminium paint including any addition / alteration (if required) for fixing street light complete all as specified and as directed by Engineer-in-charge.

M&L for Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 2.5 metres length, buried directly and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected to galvanized iron strip 32mm x 6mm thick as earth lead by means of bolts, nuts and washers of galvanised iron or steel and thimbles and other end of the earth strip connected to earthing test point/equipment and protected by galvanised iron pipe light grade 40mm dia upto earthing test point/equipment fixed with required number of mild steel clamp made out of 25mm x 3mm flat iron and perforated water pipe 20mm dia GI medium grade of length 2.25 metre and top with socket & plug and bottom connected to earth plate by slit and two bolts/nuts/washers, PCC chamber in cement concrete (1:2:4) type B-1 and 40mmthick pre-cast RCC (1:2:4) type B-0 cover with 40mm x 40mm x 3mm MS angle iron frame, excavation & earth work . complete all as specified and directed by Engr-in-charge. Notes :- (i) GI strip upto earth test point/equipment is included in this item. (ii) Outer edge of earth pit chamber shall be 1.5 metre away from the outer edge of PCC chamber. (iii) Minimum weight of reinforcement shall be 1 kg for each earth pit cover

Supply and fixing HDPE DWC Pipe dia inner dia 50mm and outer dia 63mm for laying of cable laid in trenches complete all as specified and as directed by the Engineer-in-Charge

S&F as in repair Galvanized iron tubing, 40mm bore light grade, ISI marked, including all fittings and laid in trenches / under road / drains, fixed to poles / walls with required numbers of clamps made out of 25x3mm flat iron, bolts, nuts and washers for protection of LT electric cable complete all as specified and as directed by Engineer-in-charge. Notes :- (i) Excavation & earthwork shall be measured & paid for separately under respective items of BOQ (ii) Cost of flat iron clamp if required is included in the unit rate of this item. Nothing extra shall be paid on this account. Make : Tata/Jindal/Prakash Surya or equivalent Technocommercial cat part of Make as specified in Appendix "A".

BANSAL BROTHERS (BID ID -3499145)

BISHNOI BUILDERS (BID ID -3499354)

PACHAR BROTHERS (BID ID -3499592)

M/s JUGAL KISHORE MISHRA AND SONS (BID ID -3493449)