SPL REPAIR TO BLDG NO P-423/3, 6 AT MIL STN SGNR

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding and rubbish off the premises complete all as specified and directed.

M&L 600x300x7 mm thick glazed ceramic coloured tiles as in vertical sufaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles including 10mm backing coat in CM 1:4 complete all as specified and directed.

Demolition of cement Concrete(un-renforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L non skid ceramic coloured tiles 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured polymer based grout to match over and including 20 mm thick screed bed in cm 1:4 complete all as specified and directed.

M&L 25mm thick cement concrete flooring type B0, 1:2:4 using 12.5 mm graded aggregate finished even and fair complete all as specified and directed.

Demolition of cement concrete of any description and in any position for sunken portion and floor all as specified and directed.

M&L for water proofing treatment to RCC sunken slab as specified below asd as directed by engr-in-charge:- (a) 15mm plaster in CM 1:3 with WPC on raised vertical surface. (B) Cleaning the surface with wire brush/coir brush, removing loose material like dust particles ,dirt etc. (c) Creating fillet covering of 50x50 mm with polymer modified mortar on the junction of slab and walls (d) Apply first coat of two component modified polymer coating on the horizontal and vertical surfaces. (e) Provision of glass fibre mesh of 2x2 mm immidiately on above coating (f) Apply second coat of two component modified polymer coating after 72 hours (g) Laying concrete 1:4:8 over the coating as per requirement (h) Joining the sanitary pipe with non shrink cementatiuos grout (k) Complete the treatment to be carried out by authorised applicator of waterproofing manufacturer. NOTE : (i) The Treatment shall be carried out as per the manufacturers industreis and as directed by eng-in-charge. (ii) The plan area of floor shall be consider for payment. (iii) WPC shall be measured and paid saperately.

Supply only Water proofing compound complete all as specified and directed.

Dismatiling brick tiles or terracing tiles, single layer on roofs and mud phuska complete all as specified and directed.

Demolition of old mud phuska of any type of soil and any thickness, removing rubbish of the premises cleaning surface and preparing to receive new cement plaster complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (20 mm graded aggregate) as in roof padding/roof kerbs or mud stops, rounded or chamfered on edges and laid to maintain slope complete all as specified and directed.

Providing and applying APP based polymeric membrance minimum 3mm thick reinforced with polyster non wove fabric (wt n.less than 3.0kg/sqm) laid on primed surface by forced application keep overlap margin for minimum 100mm heat both the overlaps and use round tipped trowel to seal overlap excess compound shold be smoothened and pressed into seam using hot trowel and including & applying a coat of bitumen based primer @ 3.5 sqmtr/ltr including cleaning surfaces with wire brush / coir brush to freee from all loose materials like dust, dirt ect and make wattah / coving at all horizontal and vertical joints to avoid right angle turning complete all as specified and directed. (Note : The treatment shall be carried out as per the manufacturers instrucions and by applicator of manufacturer as approved by GE.)

Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 8-10 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner complete all as specified and directed.

Dismantling water tank capacity exc 250 Ltr and n exc 1000 ltr complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank white colour 1000 ltrs capacity three layered (Cylindrical vertical with closed top) hoisted and fixed in position including 25mm bore PTMT ball valve, high pressure with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe or brass ferrule (minimum weight 455gms) complete all as specified and directed.

Taking down chowkhats or frames (without taking off shutters from the frames) not exceeding 1.5sqm each complete all as specified and directed.

S & F of Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, as per specification & drawing complete all as specified and directed.

S&F PVC door Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F Aluminium frame for doors, window, ventilators with one or more rebates including joining cleat for fixing etc complete with powder coating on Aluminium minium thickness of powder coating 50 micron as per the specification the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawl plug and screw or with fixing clip or with expansion hold plate fasteners . Aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required all complete all as specified and directed.

S&F Aluminium window and ventilator shutters, side hung type without sash bar, aluminum section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, powder coated aluminium snap beading screws, powder coated aluminium fitting such as SS hinges type B-21 100 mm size (2 Nos for each shutter), suitable handle 150mm long (1 No for each shutter), tower bolt 150mm long (02 nos for each shutter), Peg Stay hinges - 100mm long (1 Nos each shutter, Alu Handle - 100mm long (2 Nos each Shutter), Alu Tower Bolt - 100mm long (02 Nos each shutter) of any colour (thickness of powder coating not less than 50micron) etc complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and directed.

S&F Aluminum Grill powder coated of approved design/pattern with aperture size 50 mm and wire dia 3-5mm fixed with Aluminum Frame complete all as specified and directed.

S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm complete all as specified and directed.

M&L for mild steel work as in frame work/guard bar for door and window and as similar work including cutting tops to shape, drilling holes, notching for wire etc conforming to Fe-290 grade E-165 complete all as specified and directed.

Taking down chowkhats or frames (without taking off shutters from the frames) exceeding 1.5sqm but n.exc 4.0sqm each complete all as specified and directed.

S & F 1.25mm thick sheet pressed steel frames of frame size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, lock strike plate, etc., complete, as specified,supplied and fixed complete all as specified and directed.

S & F 1.25mm thick sheet pressed steel frames of frame size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, lock strike plate, etc., complete, as specified,supplied and fixed complete all as specified and directed.

M&L Cement concrete 1:3:6 type C–0(12.5 mm graded stone aggregate) filling of pressed steel frame and hold fast blocks etc complete all as specified and directed.

M & L for applying two coats of synthetic enamel paint (ordinary tint) over one coat of red oxide primer on new steel surface over 10 cm width or girth, not otherwise described including preparation of surface complete all as specified and directed.

M&L 2nd class hardwood 35mm thick factory made Glazed and skeleton shutters of door/window/ ventilaor, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S & F for 35mm thick factory made IInd class hard wood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L for preparation of surfaces of new wooden Surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

S&F 100 mm Butt hinges stainless steel with galvanised mild steel hinge pin and fixed type C-21 complete all as specified and directed.

S& F aluminium anodised barrel tower bolts of extruded section and fixed 200 mm size complete all as specified and directed.

S&F 300 mm mild steel sliding door bolts, clip type, stone enameled block with bright bolt not less than 12mm dia with and incl a minimum of 6 bolts and nuts, 4 on bolt plate 2 on staple plate complete all as specified and directed.

S & F aluminium handles D type with back plate, anodised, 150mm long complete all as specified and directed.

S&F 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor and overall length of cover plate 140 mm complete all as specified and directed.

S&F in repair 15 mm dia chromium plated concealed type stop valves, cast copper aloy with crutch or butterfly handles screwed down high pressure, screwed both ends for iron and fixed complete all as specified and directed.

S&F in repairs, Angle valves, chromium plated cast screwed down, high pressure copper alloy, with crutch or butterfly handles, screwed both ends for but fancy type 15mm bore iron pipe or complete all as specified and directed.

S&F in repairs chromium plated shower rose of any colour with or without swivel joints in square shape150mm size including long shower arm complete all as specified and directed.

S&F in repairs SS soap dish of any size fixed with screws complete all as specified and directed.

S&F in repairs grating doom 100 mm dia of stailess steel with and without hole complete all as specified and directed.

S & F in repair stainless steel tubular towel rail 20mm dia “D” type 60 cm long between flanges including brackets complete all as specified and directed.

S & F in repair stainless steel towel ring min 150mm dia including brackets complete all as specified and directed.

S&F in repairs fancy type long body bib taps,15 mm cast copper alloy, with crutch or butterfly handles, screwed down, screwed for iron pipe or brass ferrule for 15mm bore complete all as specified and directed.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F in repair water closet vitreous china squatting pan "Orrisa pattern" size 580mmx440mm white with integral foot rests (Excl flushing cistern) including all joints and making good to the floor complete all as specified including CI 'P' trap/S trap complete all as specified and directed.

S&F in repairs, PVC low level flushing cistern 10 lirs capacity, valve-less, syphonic action type, white, with inlet, ball valve, float, and handle including brackets, PVC connections 15 mm size with PTMT nuts of length 450 mm ,including 32mm bore flush pipe of polyethylene of low or high density of PVC complete all as specified and directed.

S&F, in repair vitreous china wash hand basin table top type, including brackets, 32mm bore brass chromimum plated waste coupling & 32mm bore low density ployethylene (LDPE) flush pipe of pressure rating 6Kgf/Sq cm (1.00 M long) complete, including 15mm bore 450 mm length PVC connection with PTMT nuts complete all as specified and directed.

S&F in repairs low density polyethylene pipes (LDPE) 32 mm dia and 1000 mm long of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors complete all as specified and directed.

Supply only fancy type swan neck pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure of 15 mm bore diawith or without lettered Hot or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F hat pegs and hooks (cloth hanger with six peg set each) complete all as specified and directed.

Dismantling of cast iron, PVC or 100mm dia of pipe reinforced concrete pipes jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

Dismantling of cast iron, PVC or 75mm dia of pipe reinforced concrete pipes jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

S&F 110mm dia of pipe PVC drain self it pipes, single sockets in any length, jointed with solvent cement fixed in walls and the dia of pipes complete all as specified and directed.

S&F 75mm dia of pipe PVC drain self it pipes, single sockets in any length, jointed with solvent cement fixed in walls and the dia of pipes complete all as specified and directed.

S&F 110mm dia of pipe PVC junction single 'Tee' ISI marked jointed with solvent cement fixed in walls and the dia of pipes complete all as specified and directed.

S&F 75mm dia of pipe PVC junction single 'Tee' ISI marked jointed with solvent cement fixed in walls and the dia of pipes complete all as specified and directed.

S&F 110mm dia of pipe PVC sockets equal ISI marked jointed with solvent cement fixed in walls and the dia of pipes complete all as specified and directed.

S&F 75mm dia of pipe PVC sockets equal ISI marked jointed with solvent cement fixed in walls and the dia of pipes complete all as specified and directed.

S&F 110mm dia of pipe PVC bend equal ISI marked jointed with solvent cement fixed in walls and the dia of pipes complete all as specified and directed.

S&F 75mm dia of pipe PVC bend equal ISI marked jointed with solvent cement fixed in walls and the dia of pipes complete all as specified and directed.

M&L for CI floor trap 100 mm with anti cockroaches grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

M&L for CI floor trap 75mm with anti cockroaches grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

Taking down eaves gutters and rain water pipes (any size or pattern) including all fittings, heads, shoes, bends, swan – necks, etc. including cleaning of any description complete all as specified and directed.

M&L bands straps supports or stays for rainwater ventilating pipes including bolts confirming to Fe 290 Gde E-165 complete all as specified and directed.

S&F 110mm bore PVC (SWR) rain water pipe single socketed in any length with rubber ring joints, jointed with solvent joint fixed to wall complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed.

Taking up or down for 15 mm bore steel water tubing galvanised with connection including cleaning for refixing complete all as specified and directed.

Taking up or down for 20mm bore steel water tubing galvanised with connection including cleaning for refixing complete all as specified and directed.

Taking up or down for 25mm bore steel water tubing galvanised with connection including cleaning for refixing complete all as specified and directed.

S&F CPVC pipes 20mm bore of pipe ISI marked IS 157778 with all brass fitting for hot and cold water fixed with solvent cement complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F CPVC pipes 25mm bore of pipe ISI marked IS 157778 with all brass fitting for hot and cold water fixed with solvent cement complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F CPVC pipes 32mm bore of pipe ISI marked IS 157778 with all brass fitting for hot and cold water fixed with solvent cement complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F CPVC pipes 40mm bore of pipe ISI marked IS 157778 with all brass fitting for hot and cold water fixed with solvent cement complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F push type Metropole flush valve, made of brass with CP finishing suitable for 40mm CPVC pipe complete all as specified and directed.

S&F in repairs Vitreous china premium/1st quality wash down water closet wall hung EWC white (closed pattern incl all necessary like rag bolts/gel gasket, PVC (SWR) WC connector benty type etc.) Plastic water closet soft slim seat cover, white, closed pattern with flat bottom, and cover with aluminised hinging device complete all as specified and directed.

S&F in repairs vitreous china urinals, half stall type flat back complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe grating and union for discharge pipe including waste pipe and trap complete all as specified and directed.

S&F Urinal spreader of PTMT any colour for fixing 15 mm dia pipe complete all as specified and directed.

M&L for granite (of any type) 18-20 mm thick machine cut, bedded & jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, rounding of edges (moulding of edges) and polishing complete laid over 15 mm thick screed bed in CM 1:4 etc complete all as specified and directed.

S&F Harrison rails mild steel chromium plated with fixing brackets, stops, rollers etc 20mm bore dia complete all as specified and directed.

M&L for 75mm thick Cement concrete type C-2 , 1:3:6 (40 mm graded aggregate) as in plinth protection laid in bay n.exc 2.5m length complete all as specified and directed.

Demolition of RCC as in Roofs, floors ( other than ground floors), beams, staircases, landing, chajjas, Parapet wall and similar suspended work complete all as specified and directed.

Demolition of brick work built in cement mortar of any description complete all as specified and directed.

M&L brick work with sub class 'B' Bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 complete all as specified and directed.

M&L Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick (horizontal or sloping) complete all as specified and directed.

M&L for RCC nominal mix 1:1 1/2: 3 (using 20mm graded aggregate ) as in slabs suppotred on walls, beams and columns complete all as specified and directed.

S & F for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia complete all as specified and directed.

S&F plain mild steel sheeting 0.80mm thick in expansion/bldgs joints gutter valley, hips with screw and fastners including all fixing cleats etc complete all as specified and directed.

Taking down cement plaster of amy description on bricks or concrete surfaces of walls including racking out joints, hacking for keys scrubbing down with water etc. complete all as specified and directed.

M&L 15mm thick, rendering in cement mortar 1:6 to brick/concrete wall surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L 15mm thick, rendering in cement mortar CM 1:4 to brick/concrete wall surfaces in two layers first layer 10mm thick and second layer 5mm thick with WPC 3% by wt of cement finished fair and even without using extra cement complete all as specified and directed.

M&L 5mm thick, rendering in cement mortar 1:3 to ceiling surfaces on patches finished even and smooth without using extra cement in patches complete all as specified and directed.

M&L for preparation of New Plastered Internal Wall surface and applying the following :- (a) Applying one coat wall care putty (1.0mm thck) on wall surface and smooting the surface with sand jpapers/Mechanised sanding etc prepatory to paint as complete all specified and directed. (b) Applying one coat of interior Wall primer using Roller over finished putty surfaces complete all as specified (c) Applying Two coats of Interior Apcolite Premium Emulsion with roller to achieve smooth finishes complete all as specified. Note : Contractor may use manual preparaion of surfaces where mechanically is not possible with prior approval of Engineer-in-Charge.

M&L one coat of Acrylic emulsion on newly plastered ceiling surface over one wall care putty (1.0mm thick) including one coat of primer and preparation of surfaces complete all as specified and directed.

M&L for preparation of New Plastered External wall surfaces and applying the following :- (a) Applying one coat wall care putty (1.00 thick) on wall surface and smoothning the surface with sand papers/Mechanised sanding etc prepatory to paint as directed complete all as specified. (b) Applying one coat of exterior wall primer using Roller over finished putty surfaces complete all as specified. (c) Applying Two coats of Apex Advanced Dust Proof Emulsion with roller to achieve smooth finishes complete all as specified. Note : Contractor may use manual preparation of surfaces where mechanically is not possible with prior approval of Engineer-in-Charge.

M&L for complete removal of existing treatment on old internal wall surfaces of any description, preparation of surface by Mechanised sander having suction vaccum Bag using Smart periodical methodology and after preparing the surfaes applying the following complete all specified and directed. (a) Applying one coat wall care putty (1.00mm thick) on wall surface and smoothning the surface with sand papers/Mechanised sanding etc prepatory to paint complete all specified and directed. (b) Applying one coat of interior wall primer using rollery over finished putty surfaces complete all specified and directed. (c) Applying Two coats of Interior Apcolite Premium Emulsion with roller to achieve smooth finishes complete all as specified and directed. Note : Contractor may use manual scraping tools for complete removal an surfacs prepartion with prior approval of Engr-in-Charge in case of places where using of Mechanical equipment are not feasibel are note possible.

M&L for two coat of acrylic emulsion of old decorated surfaces of ceiling including preparation of surfaces by brooming down or steel sire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots complete spots complete all as specified and directed.

M&L for complete removal of existing treatment on old external wall surfaces of any description, preparation of surface by Mechanised sander having suction vaccum Bag using Smart Periodical methodology and after preparing the surfaces applying the following complete all as specified and directed. (a) Applying one coat wall care putty (1.00mm thick) on wall surface and smoothning the surface with sand papers/Mechanised sanding etc prepatory to paint complete all specified and directed. (b) Applying one coat of exterior wall primer using rollery over finished putty surfaces complete all specified and directed. (c) Applying Two coats of Apex Advanced Dust Proof Emulsion with roller to achieve smooth finishes complete all as specified and directed. Note : Contractor may use manual scraping tools for complete removal an surfacs prepartion with prior approval of Engr-in-Charge in case where using of Mechanical equipment are not possible.

S & F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S & F for 20mm dia Gun metal , gate or globe valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F for 25mm dia Gun metal , gate or globe valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

M&L for Mild steel work as ISMB,joists channel,angle or tee section fixed adjacent to ceiling and embedding in floor and brickwork including cutting welding and the like including caps.bases,splices etc,built from one or more beam or channel section or angle with plates including all lattice bars, stiffeners,gusset plates including necessary welding,rivetting etc.confirming to Fe 410 (Gde E-250) quality A etc complete all as specified and directed.

Shotcreting average thickness 25mm in RCC columns, beams and slab etc. (with mix minimum cement content of 350 Kg per Cum, M-25). Concrete having the specified minimum characteristic compressive strength (with ordinary portland cement, coarse sand and graded stone aggregates of 6mm to 10mm size in proportion as per design criteria) incl the cost of centering and shuttering at edges and corner etc as directed by Engr-in-Charge incl chipping of unsound/week concrete material 25mm average thickness from slabs, beams/columns etc with mannual Chisel or standard power driven percussion type all of approved makes incl tapering of all edges, making square shoulder of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes and throughly washing with water and allowing it to dry etc incl removel of rust by applying approved rust remover chemical and the coating with Dr Fixit Epoxy zinc primer @ 6 Sqm per Litre at DFT of 100 micron as per manufacturer's instruction and specification, including removing rubbish material from building and thrown in low lying empty area at any distance from the site as directed complete all as specified and directed. Make :- Sika / Fosroc/Pidilite or Techno commercial equivalent make approved by GE in writing from E-in-C's approved list. Note : Complete treatment to be executed by approved applicator.

Supply and fixing hard drawn steel wire fabric not exc 4kg/sqm cut to lengths, wire mesh to be fixed and firmly anchored to the concrete surface by means of 'L' shaped mild steel shear key welded with existing reinforcement including cost of material, labour, tools and plants incl welding/L-clip/tying with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Drilling Holes of 12mm dia up to 100 mm deep holes in structural members at the interval of 300 mm in staggered manner or along the crack line in Reinforced Concrete (RC) structural element including cleaning of the holes by air blower and inserting 12mm dia NRV (Non Returnable Valve) nozzle compatible with epoxy injector and having machined external end to receive outlet of Grouting Gun. Fix inside the hole by applying thixotropic epoxy adhesive to ensure complete sealing and allow curing the system for minimum of 8 Hrs before Grouting including nozzle projections, excess putty, if any, over concrete element by grinding, leveling and finishing the external surface, after completion of the work, etc. complete all as specified and directed.

Grouting, injecting two part, low viscosity, moisture insensitive injection liquid, based on high strength epoxy resin by pressure and using pressure epoxy injector with accessories till nozzle refused to accept the grout including mixing of grout having following properties:- (i) Mixed Density 1.1 kg/l (at +27°C); Viscosity ~ 250 mPas at +30°C and should comply according to ASTM C 881, Type II and IV, Grade-1, Class E+F (ii) Compressive strength >= 70 N/sqmm (7 days) according to ASTM C 579; Tensile Strength ~ 50 N/sqmm (after 7 days at +30°C cure) (According to ASTM D 638); Tensile Modulus ~ 2000 N/sqmm (after 7 days at +30°C cure) (According to ASTM D 638); (iii) Bond Strength ~ 10.8 N/sqmm (failure in concrete) after 14 days at +30°C cure; Flexural strength ~ 50 N/sqmm according to ISO 178. (iv) Seal the nozzle with thixotropic epoxy adhesive after the refusal of grout material from the nozzle. Note:- leakage through other nozzle or cracks are required to be monitored while grouting and such points to be sealed as and when required without any extra cost complete all as specified and directed. Note :- Mode of measurement: per kg of material consumed Make: Sika - SikaDur 52 LP/ Fosroc- Conbextra EP 10/ Pidilite Dr Fixit Epoxy Injection Grout or equivalent make approved by GE in writing from E-in-Cs Br approved list.

Taking down carefully aluminium point wiring (light, fan, socket or power, bell complete fitting such as sockets, ceiling roses, pendants, batten holders, regulators and making good the disturbed surfaces of wall, floors, ceiling in CM 1:3 etc complete all as specified and directed.

M & L for concealed conduit point wiring complete for light/ fan on independent /combine board with cable 1.5 sqmm (Nominal area) FRLSH PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC Concealed conduit pipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , after cutting in wall chasing for conduits and sinking's for Sunken cast iron prossed steel terminal boxes suitably length and thickness for mounting switch, sockets, fan regulaor with 3mm thick plastic laminated sheet cover fixed with brass screwed and cup washer duly grouting and painted with red oxide metal primer and making the good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth continuity conductor along with point wiring of 1.5 sqmm copper PVC insulated cable for one light/ fan point controlled by one switch and connected to common earth dolly, complete all as specified and direced.

All as per Srl item No 112 here in before but for one switch socket combination 5/6 amp on independent board complete all as specified and directed.

All as per Srl item No 112 here in before but for one three pin socket outlet 5 Amps on same board with other switches complete all as specified and directed.

All as per Srl item No 112 here in before but for one switch socket combination 6 pin 5/15 Amps on independed board with copper conductor 2.5 sqmm alongwith 2.5 sqmm earth contunity conductor complete all as specified and directed.

All as per Srl item No 112 here in before but for one light point controlled by two 2 ways switches complete all as specified and directed.

S&F switch piano flush type 5/6 Amp single pole one way, one module complete all as specified and directed.

S&F switch socket combinatin 5 pin, type 5/6 Amp flush type complete all as specified and directed.

S&F replacement switch socket combinatin 6 pin, type 5/16 Amp flush type complete all as specified and directed.

S&F switch 2 way 6A complete all as specified and directed.

S&F socket outlet 5 pin 5 Amps flush type complete all as specified and directed.

S&F stepped type fan regulator not less than 120 watt for ceiling fan 1200/1400mm sweep complete all as specified and directed.

S & F ceiling rose surface bakelite three terminals complete all as specified and directed.

S & F in replacement of existing light fitting with LED batten with aliminium housing and integrated electronic driver, 20 watt having input voltage AC140-300V, 50 Hz , 6500K, and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed.

S&F in replacement compact and decorative energy efficient LED mirror light fitting with antiglare diffuser and decorative end caps suitable for 1X20 watt fitting 2 ft version including LED lamp 20 watt complete all as specified and directed.

S&F in replacement of security light fitting LED TYPE 25 watt with all necessary acessories, Clear transparent acrylic cover, prewire suitable to operated on 230 volt 50 HZ AC & Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed.

S & F in replacement angle holder insulated body with back plate for conduit fittings complete all as specified and directed.

S & F LED lamp 9W for angle holder complete all as specified and directed.

S & F in replacement of sub-main wiring with PVC insulated and un-sheathed 2x6.00 sqmm (Nomianl Area) FRLSH stranded copper conductor drawn in and including PVC "medium quality" conduit as per size required inlcuding 1 x6 Sqmm (Nominal Area) Copper cable as earth contiunity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour, necessary junction box and covers including necessary connections, PVC flexible pipe are used in pannel board while connection the cable complete all specified and directed. (Note : PVC cable and PVC conduit shall be ISI marked) (Note : Four length of 6 sqmm cable and two length of 6 sqmm earth cable along with PVC conduit will be measured as one running length)

S & F in replacement of sub-main wiring with two single core cables PVC insulated and un-sheathed 4 sqmm (Nominal Area) FRLSH stranded copper conductor drawn in existing PVC conduict including 4.00 Sq mm (Nominal Area) copper cable as earth continuity conductor including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed. (Note : Two lengths of 4.0 sqmm cable for one length 4.0 sqmm earth cable alongwith PVC conduit will be measured as one running length)

S & F in repairs sheet metal enclosure for double door Vertical DBs made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounting VTPN 4 Way 415 Volts, ISI marked 250 amps bus bar stove enameled dust and vermin proof, IP:43 protection suitable for incorporation FP MCCB (V-Tech) N3 Frame upto 250A, Isolators and Including give connection with wire and cable etc complete all as specified and directed.

S&F in repairs MCCB TP & N 63 Amps with breaking capacity 16KA, Fixed TM and 415 volts AC supply ISI marked complete all as specified and directed.

S & F in repairs sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 8 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed.

S & F in repairs MCB ‘C’ series type suitable for 240 volts, AC supply 32Amps, S P & N with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed.

S & F in repairs MCB ‘C’ series type suitable for 240 volts, AC supply 5 to 32Amps, S P & N with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed.

M & L for Earthing complete with GI earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 Mtr deep below ground level ) with top edge of plate not less than 1.5 Mtr below ground level , connecting to GI earth lead 4 mm dia GI earth wire ,by means of bolts,nuts and washers of GI and protection by provision of GI medium grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20 mm grade stone aggregate with 40 mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 gs /Sqmm ) and frame of angle iron 25mmX25mmX6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape ,GI light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed ontop edge of earth plate common salt and charcoal filling test point made out of 40 mmX 8 mm FI with fixing arrangement ,funnel, wire mesh and earth work inhard dense soil ,returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electric plate no.3 of SSR part 1 and connecting to earth test point including taking out unserviceable earthing with all acessories all as specified or indicated including testing on completion all as specified and directed.

S&F Taking down and depositing of old unsv ceiling fan of any size in MES Yard, complete all as specified and directed.

Hanging only ceiling fan (M.D. supply) and connection up including provision of cable from ceiling rose or connectior to fan complete all as specified and directed.

S&F Taking down and depositing of old unsv Exhaust fan of any size in MES Yard, complete all as specified and directed.

Fixing only Exhaust fan (M.D. supply) and connection up including provision of cable from ceiling rose or connectior to fan complete all as specified and directed.

S&F Taking down and depositing of Geysers of any size and capacity in MES Yard and refixing the same in existing position complete all as specified and directed.

R B Infrabuilders (BID ID -3165217)

M/s HANS BROTHERS (BID ID -3161414)

AYUSH BUILDERS (BID ID -3167197)

Easyways Enterprises (BID ID -3163524)