SPECIAL REPAIR TO BUILDING NO P-16 AT CHINDIT TOP AND PROVISION OF TOILET OF 10 BLOCK NEW LOCATION ERSTWHILE ASC BN ILP IN DAHUNG WITH PROVISION OF 32 X EXHAUST FAN IN CHINDIT TOP UPPER DHAUNG OFFICERS MESS LOCATION OF ASC BN OF AGE B/R AND AGE E/M U

Amount

Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out in hard /dense soil

Excavation over areas n exc 1.5 m deep and getting out in hard/dense soil with complete all as specified and directed.

Excavation in trenches n,exc 1.5 m wide and n.exc 1.5 m deep for foundation and getting out in hard/dense soil with complete all as specified and directed.

M&L PCC 1:4:8 type D2(using 40mm graded aggregate)as in foundation filling and mass concrete etc with complete all as specified and directed.

M&L for PCC 1:3:6 type C-1(20 mm graded aggregate) precast cement concrete block masonry with solid blocks exc 10 cm in width and setting in CM 1:6 etc complete.

M&L for precast cement concrete solid building blocks (1:3:6), type C-1, 10 cm thick (with plain or interlocking joints as directed) setting in cement mortar (1:4), complete, laying inner side of wall with complete all as specified and directed by Engr-in-Charge.

M&L for re-inforced cement concrete 1:2:4 type B-1 (20mm graded aggregate) as in beams, plinth beams, cantilevers, bressummers, lintels over 1.5 m span etc complete with complete all as specified and directed.

M&L for MS TMT bars 10mm dia and over, cut to lenth, bend to shape required, including cranking, bending, sprially for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips with complete all as specified and directed by Engr-in-Charge.

M&L for MS TMT bars 05mm dia and over, upto and including 10 mm dia in stirrups, spaces and binders.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished surfaces of concrete.

M&L rendering 15 mm thick in CM 1:4 on concrete surfaces finished even and smooth without using extra cement with complete all as specified and directed by Engr-in-Charge.

M&L Second class HW in Scantling clean sawn with complete all as specified and directed by Engr-in-Charge.

M&L for rendering 15 mm in CM (1:6) over concrete wall surfaces finished even and smooth without using extra cement.

M&L for newly plastered surfaces of walls and applying two coats of cement based paint, over a coat of primer with complete all as specified and directed.

M&L for Preparing newly plastered surfaces of walls and applying two coats of white wash.

Returning/filling in including spreading, levelling, watering and well remming in hard/dense soil.

Removing excavated material n.exc 50m and depositing where directed at a level n exc 1.5m above the starting point.

M&L hard core of gauge n.exc 63mm, deposited, spread and levelled in layers nexc 15 cm thick, watered and rammed to a true surface.

M&L for 75 mm thick PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) as cement concrete in Sub-base floors, sub-bases floors and pavings etc complete all as specified.

M&L for 75mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in plinth protection surface finished even and smooth using with extra cement

M&L for 25 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) in sub base of floorings.

M&L for 15 mm thick screed bed in CM 1:4 for laying floor tiles with complete all as specified and directed by Engr-in-Charge.

M & L for Non-skid ceramic tiles 7 to 8 mm thick coloured tiles( square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match.

M & L for 10mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces finshed rough to receive tiles .

M & L for 350 x 250 x 7 mm/450 x 350 x 7 mm thick glazed coloured ceramic tiles on vertical surface of wall set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade.

S & F 3mm thick figured glass, pin head glazing with oil putty /wooden beads in squares n exc 0.50 Sqm in each pane.

S&F Pre-Painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour havimg testile strenght of 550 Mpa as in roof covering/ cladding to wall , fixed with self tapping screws as specified and directed.

S&F Pre-Painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour havimg testile strenght of 550 Mpa as in roof covering/ cladding to wall , fixed with self tapping screws as specified and directed.

S&F solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying and fixing in opening as per specification and drawing.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement supplying & fixing in the frame at site as per specification & drawing with complete all as specified and directed by Engr-in-Charge.

S&F 100mm size stainless steel butt hinges, medium weight, cold rolled complete with stainless steel screw etc. all as specified as directed.

S& F Aluminium anodised barrel tower bolts 200mm long of extruded section and fixed

S& F Aluminium anodised barrel tower bolts 150mm long of extruded section and fixed

S & F 150mm size extruded aluminium alloy handles, fabricated type anodised

S & F 100mm size extruded aluminium alloy handles, fabricated type anodised

S & F vitreous china Squatting pan 'Orissa Pattern' size 580 x 440 mm white with integral foot rest.

S & F in repair vitreous china wash down water closet pan (pedastal pattern) white including connecting to trap and to flushing pipe etc complete all as specified.

S&F in rep Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repair toilet paper holder of brass,chromiun plated or stainless steel

S & F 10 litres PVC, Syphonic action type, Flushing cistern low level, white with inlet ball valve float chain and pull and brackets complete.

S&F PVC (SWR) pipes single socketed 110mm dia in any length with rubber ring joints fixed to walls

S&F PVC (SWR) pipes single socketed 75mm dia in any length with rubber ring joints fixed to walls

S&F PVC (SWR) junction single, (single T) equal or unequal with access door 110mm dia.

S&F PVC (SWR) junction single, (single T) equal or unequal with access door 75mm bore.

S&F PVC (SWR) bends any radius, bend 110mm dia.

S&F PVC (SWR) bends any radius, bend 75mm dia.

S&F PVC (SWR) vent cowl 110mm dia

S&F PVC (SWR) WC connector 110mm dia lip ring.

S&F 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement.

S&F PVC (SWR) couplers 110mm bore.

Dismantling of water tanks exc 500 ltrs & n. exc 1000 ltrs capacity and removing to store.

Taking up or down 15 mm bore steel water tubing and connections including clfor refixing or removal to store

Refixing 15 mm bore old steel tubing and conncetions in new or old position to walls

Taking up or down 20 mm bore steel water tubing and connections including cleaning or refixing or removal to store

Refixing 20 mm bore old steel tubing and conncetions in new or old position to walls

S & F 15 mm bore Galvanized Steel tubes, medium grade with all fittings for water supply pipes fixed to walls .

S& F 20 mm bore galvanised steel tubes medium grade with all fittings for water supply pipes fixed to walls.

S&F 15 mm dia bib taps, fancy type chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixed.

S & F in repairs chromium plated fancy type 15mm dia bib tap, cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specifed.

S&F 15mm bore angle stop valves, fancy type chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for unions & fixed.

S&F 32 mm bore Low density poly ethylene pipes of pressure rating 6kgf/cm2 fixed complete to walls,ceiling or in floors etc.

S & F framed work such as grills, gratting,framed brackets of angles or tees with web and flange cut to shape etc with ends of bars, shouldered and/or reveted, or forged into spikes, framed guard bars, framed works of water tankes stagging,gates and similar work con-forming to Fe.290.Gde-E-165.

S&F Rotational mounded polythene water storage tank of 1000 ltrs capacity, (multilayered, cylindrical, vertical with closed top) hoisted and fixed in position as specified in SSR Pt-I.

S&F ball brass valves high pressure with polythene float and fly nut complete screwed for iron pipes of 20 mm dia or brass ferrule and fixed, all as directed.

S&F Gun metal globe or gate valve with Iron wheel head, screwed both ends for 20 mm dia of pipe and fixed.

Material and labour for providing PCC (1:3:6) type C-2 as in concrete bed to drain pipes including packing under and haunching against the sides of pipes of bore 150mm on after they are laid and tested complete all as specified and directed..

Material and labour for Salt glased stone ware drain pipe 150 mm dia grade A laid in trenches and jointed in cement mortar 1:1 complete all as specified and directed.

Demolition of cement concrete in roofs, floors, beams, staircases, landing and similar works (other than ground floor) etc complete.

M&L for PCC 1:2:4 type B1 using 20mm graded stone agg as in roof padding finished even and fair .

M&L 10mm thick rendering in CM 1:4 on roof surfaces finished even and smooth without using extra cement using WPC @3% by weigh of cement .(WPC will be measured and paid separately)

M&L for preparation of new plastered surfaces of roof surfaces and applying waterproofing treatment over smooth finished surfaces after application of cold applied bituminous primer @ 0.30 kg/Sqm and applying hot bitumen 85/25 @ 1.20 Kg/Sqm providing and laying APP polymer, modified, non-woven polyester mat, reinforced membrane, 3.00mm thick , weighing 3.5 Kg /Sqm with surface finish by torch application method, with minimum 75 mm overlap on longitudinal direction and 100 mm overlap on the transverse direction and finally applying with one coat of bituminous based solar reflective aluminium paint @ 100 gms/ Sqm complete all as specified and directed.”

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level)

M&L for screed bed or bedding layer of mortar 20mm thick in CM 1:6 for laying floor finishes

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete.

M&L for chequered cement concrete tiles 20cm x 20cm x 25 mm with grey cement and no pigment thk set,jointed in neat cement slurry in floors

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for

M & L PCC 1:3:6 type C1, (using 20mm graded stone aggregate) as in surface channels and drains .

Extra for forming fair finishing drain or channels 30 cm inner girth in cement concrete using extra cement including forms, moulds stopped ends etc.

Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided for.

M&L for form work to chullah hoods,chajjas,troughs and similar items including edges with fair finish flat surfaces

M&L for reinforced cement concrete 1;2;4 type B1 (using 20 mm graded stone aggregate) for slabs supported on walls , beams and columns, in floors , roofs, landings and in shelves ,chhajja's and the like complete with all necessary formwork etc all as specified and as directed.

Demolition of stone slabs or tiles of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc

M&L19- 20 mm thick granite (of any type) work (table rubbed and polished) in cooking platforms in CM 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite all as specified.

Demolition floor, hearth or tiling including cement mortar bedding (but not backing).

M&L for 10mm thick rendering in CM 1:4 finish even and fair for laying wall tiles.

M&L for Dark shade vitrified tiles 10mm thick (square/rectangular) polished, area of each tile not exceeding .36 sqm,in floors etc set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade.

Demolition of precast cement concrete articles and precast concrete block walling built in cement mortar

Taking down cement plaster on brick, concrete stone surfaces etc including raking out joints, hacking for key, scrubbing down with water etc.

M & L 10 mm thick rendering in cement mortar 1:6 on brick or concrete surfaces finished even & smooth without using extra cement

Material and labour for 05 mm thick rendering in cement mortar (1:3) on brick or concrete surfaces of ceiling finshed even and smooth without using extra cement.

M & L for 15 mm thick plaster in cement mortar 1:4 on brick or concrete surfaces using WPC @ 3% by weight of cement over finishing the surfaces even & smooth without using extra cement. (WPC will be measured and paid separately)

Supply only integral water proofing compound.

Dismantling of CI soil, rain water pipes, cast and vent pipes of any dia, any pattern including all fittings.

S&F toilet mirror cabinet of size 432 x 311 mm , fitted with 4mm thick superior quality distortion free mirror, fixed to wooden plugs with chromium plated brass screws complete all as specified and directed

S&F vitreous china wash hand basin white flat back of size 550mmx400 mm including cutting for and pinning in end of brackets,32 mm waste fittings,brass chromium plated for glazed ware sinks,basins etc.with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed.and flush pipe of polytethylene of low or high density or PVC 32 mm dia with complete all as specified and directed by Engr-in-Charge.

S&F PVC connections 15 mm size with PTMT nuts of length 450 mm.

S & F in repair plastic water closet seat cover, white closed pattern with flat bottem, and cover and mild steel chromium plated or aluminised hinging device complete.

S&F in repair brass chromium plated shower rose 125mm dia with swivel joints including fixing to steel pipe or union complete all as specified and directed

S&F brass chromium plated sink mixer table mounted with 450mm long braided hoses screwed down for 15mm bore iron pipe complete all as specified and directed.

S&F central hole basin mixture brass CP for hot and cold water screwed down for iron pipe complete all as specified and directed

S&F 15mm Brass CP wall mixer for mixing hot & cold water screwed down for PPRC/steel pipe or union of 15mm dia complete all as specified and directed

Supply and Fix in repairs plate rack made of stainless steel 0.50mm thick,over all size 762mm(H)x787mm(W)x254mm(D) complete all as specified and directed.

S&F sink with drainage board made of stainless steel 1.00 mm thick kitchen with plug washers, wastes;including bedding in cement mortor on dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 x 460 mm with bowl size 410 x 330 x 160mm, complete.

Dismantling plain or corrugated steel sheeting of any thickness as in roof coverings complete all as specified and directed.

S & F 0.63 mm thick galvanised corrugated steel sheeting with two corrugation side lap fixed with L type or J type or cranked hooks, bolts with grade of zinc coating 275 complete all as specified.

S & F plain galvanised MS sheet sheeting 0.80 mm thick in ridges ,valley gutters, hips with grade of zinc coating 275.(Make:TATA/Sail/ Jindal)

Dismantling of wall and ceiling boards(fibre pulp,insulation,etc)or insulation boards/slabs/blankets any thickness, including cover fillets and snap grid.

S&F for anodised aluminium snap grid of size 605X605X mm frame work for false ceiling with aluminium anodized section size, wall angle 40mm X25mmX2mm thk, main/cross tee-section 36.5 X 25 X 1.4mm and 23.5mm X 26.4mm 1.4mm and susupended with 6mm dia GI wire respectively with and including 8mm thk laminated Gypssum board fixed to aluminium snap grid all as per clause 10.38.1 of SSR Part-I and as per manufacturer's instructions complete all as specified and as directed by Engineer -in-charge make:(i) Aluminium section : Valco,HINDALCO, JINDAL (iI) Gypsum Board: GYPSUM IND LTD,SAINT GOBLIN

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 Sqm but not exc 4 Sqm.

All as per item No 110 above but area not exc 1.50 Sqm.

Taking down shutters of any descriptions exc 1 sqm but n exc 2 Sqm each and refixing in the same opening after repair.

M&L cutting holes exc half brick but not exc one brick in brick walls built in Cement mortarM or Cement lime mortor and stone walls built in lime mortor

S & F 2nd calss hard wood plain solid straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered, put together with glue pinned at joints complete

S & F mild steel bands, straps, clamps, hold fasts, wall ties and similar articles conforming to Fe-310-0

S&F MS window guard bars, window frames etc articles confirming to Fe 410-0 or Fe 310-0.

S&F 30mm thk flush shutters,solid core construction,with block board core and plywood face panels,commercial type on both side

M&L for power coated anodised aluminium frame for doors, windows, ventilatores with one or more rebated including joiing cleat for fixing etc complete all as specified and direcyed

S&F aluminium grill with frame to aluminium window including any stracted aluminium section and necessary fittings and fixtures etc complete all as specified and directed.

S & F Anodised aluminium window and ventilator shutters, fixed type without sash barsaluminium section weighing 0.55 kg/m including necessary joining cleats, glzing clips,rubber packing,anodised aluminium snap beading,screws etc and power coating of any colour(thickness of powder coating not less than 50 micron.) complete all as specified.

S&F in repair 300mm Mild Steel ordinary rat tail rod pattern springs including roller plate complete.

S & F in repair aluminium alloy, anodised, sliding door bolts 300mm size with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed

S&F pre coated mild steel floor door stopper ,tongue anodized 140mm length including vulcanised rubber piece

S&F in repair hasp and staple 125 mm safety type, aluminium anodised fixed with screws.

S&F PVC coated 25mm dia mild steel curtain rod of medium weight and fixing brackets, curtain ring @ 7 nos/Rm and decorative end supports etc complete all as directed”

M&L 2nd class HW plain fillets,square,rectangular or triangular in sec wrought secured with nails or brads.refixed in old position sectional area exc 3 sqcm & not exc 6 sqcm

Material and labour for prelaminated particle board 18/19 mm thick, exterior grade prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work as in shutters for kitchen shelves/cupboards fixed in repairs.

S&F continuous hinges (Piano) hinges,30mm brass,brighgt finish or electro galvanised

S&F Ball catches with 8mm dia steel ball , and brass body and striking plate including letting in and fixed

S & F sheet glass 3mm thick ordinary quality and glazing with oil putty in squares n exc 0.50 Sqm in each pane.

S&F fixed in repairs galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of apperture 1.18 mm and fixed with tinned tacks or galvanised wire staples.

M & L for preparing new wooden surfaces of any description, not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

Material and labour for preparation of old surface of wood and wood based materials over 10 Cm width or girth and applying one coat of synthetic enamel paint as directed and specified.

M & L for applying two coats of synthetic enamel paint over a coat of red oxide primer to steel and iron surfaces of any description over 10 cm in width or girth not otherwise described including preparation of new steel surfaces.

M & L for applying one coat of synthetic enamel paint to steel and iron surfaces of any description over 10 cm in width or girth not otherwise described including preparation of old steel surfaces.

Material and labour for Preparing newly plastered surfaces of walls and applying three coats of white wash.

Material and labour for Preparing old plastered surfaces of walls and applying one coat of white wash.

Material and labour for Preparing old plastered surfaces of ceiling and applying one coat of white wash.

Material and labour for Preparing newly plastered surfaces of ceiling and applying three coats of white wash.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of alkali resistant primer.

Material and labour for preparation of old distempered surface of walls including washing down and stopping of distempered surfaces and applying one coat of distempered oil emulsion all as specified and directed.

M&L for complete removal of existing treatment and appling two coat of cement base paint over one coat of primer complete all as specified

Material and labour Preparing newly plastered wall surfaces and applying Two coats of cement base paint on wall surfaces over one coat of primer

S&F Gate and shutter, hooks and eyes 75mm brash type

S&F Mortice mild steel night latch 4 levers, size 65 mm

S&F Towel rail 600mm long of PTMT fixed with and including CP brass screws and wooden/plastic cleats.(minimum wt-190gms)

Material & Labour for Point/fan wiring with 1.5 sq mm (nominal area), PVC insulated sheathed (HRFR), 1100 volts grade, multi-stranded copper conductor, in and including PVC casing capping of adequate size with all fittings and accessories including PVC boxes for housing the switches ( Make of box Prestoplast,Prestoteak), including PVC insulated and unsheathed (HRFR)single core multi-stranded copper conductor cable of size 1.5 sq mm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed.

All as per item No. 147 here in before One 3 pin socket outlet, 5 Amps on the same board with other switches, with cables 1.5sq. mm size

All as per item No. 147 here in before but for one 3 pin socket outlet 5 Amps three pin controlled by one switch on independent board complete all as specified directed.

All as per item No. 147 here in before but for one 5 pin socket outlet 15 Amp and 5 Amp Multipurpose independent using 2.5 Sqmm copper conductor cable (multi-strand) PVC insulated and unsheathed cable and 2.5 sqmm copper (multistrand) PVC insulated and unsheathed earth wire with PVC boxes complete all as specified.

M&L for Point wiring for one socket outlet 15 Amp on independent board with 4 sq mm (nominal area), PVC insulated sheathed (HRFR), 1100 volts grade, multi-stranded copper conductor, in and including PVC casing capping of adequate size with all fittings and accessories including PVC boxes for housing the switches including PVC insulated and unsheathed (HRFR)single core multi-stranded copper conductor cable of size 4 sq mm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed.

Supply & fixing switch piano flush type (ISI marked), single pole, one way 5 Amp, 240 Volts complete all as specified & directed.

Supply and fixing ceiling rose, surface bakelite, 65mm x 50mm , two to three terminals complete all as specified & directed.

S & F exhaust fan sweep 450 mm voltage 230 V 50 Hz 1200 RPM noiseless metal body light-weight rust proof body self closing louvers and blades complete all as specified and as directed.Make :- Havells/ USHA/ Crompton

S & F exhaust fan sweep 230/300 mm voltage 230 V 50 Hz 1200 RPM noiseless metal body light-weight rust proof body self closing louvers and blades complete fittings all as specified and as directed.Make :- Havells/ USHA/ Crompton

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm

Cutting of existing wall of any type & making for fixing exhaust fan on wall & repairing the same and matching with existng complete

Supply and fixing LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder, two square box for mounting including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose comple

SS & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

S&F lamp holderinsulated body PVC/ polycarbonate type with back plate for batten fitting with one PVC block of complete all as specified and directed.

S&F 1x 10 watt LED lamp complete all as specified and directed. Make: Havells/ Phillips/ CG/ Bajaj

Supply & Fixing sheet metal enclosure with double door for DBs conforms to IS:8623.III , IP:43 protection, shrouded neutral link & earth bar and cement spill protector, 8 way, 240 Volt incl fixing on suitable size of PVC rectangular plastic laminated sheet complete all as specified and directed. Make : Havells/ABB/Schneider/Legrand

Supply and fixing miniature circuit breaker (MCB) SPN 32 AMP, 240V, 10KA, 'C' curve in the MCB DB complete with connection testing and commissioning as specified and directed.

Supply and fixing miniature circuit breaker (MCB) SP 5 To 32 AMP, 240V, 10KA, 'C' curve in the MCB DB complete with connection testing and commissioning as specified and directed.

Supplying and fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor 16 sq mm, served with inner sheathing of PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular incl taking down/ dismantling of old one complete all as specified and directed.

Earthing complete with galvanised steel earth electrode plate of size 600x600x6mm thick, buried directly in ground (earth pit nbot less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.50m below notmal ground level, connected to galvanised earth lead wire 4.0mm dia by means of suitable GI nuts/bolts and brazed properly up to main board including earth pit in cement concrete 1:2:4 type B-1, precast RCC cover in 1:2:4 reinforced with expanded metal, with suitable handle, excavation and earth work in any type of soil and including medium grade GI watering pipe 25mm bore with funnel wire mesh and medium grade GI wire protection pipe 25mm bore up to main board complete as shown in electrical plate No 3 of MES schedule Part-I 2009, connected to earthing testing point including taking out existing unsv earthing complete ass as specified and testing on completion with complete all as specified and directed by Engr-in-Charge. .Note - The units rate including the cost of excavation & earth work in any type of soil, charcoal & salt in alternate layers, 25mm GI pipe (light grade) for watering 25mm GI protection pipe (light grade) funnel wire mesh PCC chamber in PCC 1:3:6 type C-1 cast iron frame and 40mm thick RCC cover for pit etc & no extra payment will be made.

Supply & fixing Modular switch 1 way 6A,1 module, 240 Volts complete all as specified & directed.

Supply & fixing Modular switch 1 way 16A,1 module, 240 Volts complete all as specified & directed.

Supply & fixing Modular Socket, 6A - 5 pin combined 2 module, 240 Volts complete all as specified & directed.

Supply & fixing Modular Socket 6A/16A - 5 pin combined 2 module, 240 Volts complete all as specified & directed.

S&F modular White cover plate with frame 01 module

S&F modular White cover plate with frame 02 module

S&F modular White cover plate with frame 03 module

S&F modular White cover plate with frame 04 module

S&F modular White cover plate with frame 06 module

S&F modular Metal flush box 1/2 module

S&F modular Metal flush box 3 module

S&F modular Metal flush box 4 module

S&F modular Metal flush box 6 module

Supply and fixing ceiling rose, surface bakelite, 65mm x 50mm , two to three terminals complete all as specified & directed.

S&F LED lamp 10 Watt, CDL, B-22 cap, (Pin type), 230W, PF not less tha 0.85 (min). Make- Havells/Crompton/Syska

Supply and fixing LED light fitting 1 x 10 Watt 220 volt AC decorative box type with driver, holder including LED tub light connecting up with three core flexible copper conductor cable of size from ceiling rose complete all as directed.

S&F LED bulkhead fitting 10 watt (Endura Ruby) with all accessories and including connenting up with twin core twisted with flexible copper conductor cable with suitable size of 230 volts , 50 hz complete all as spicified and directed.

Supply and fixing LED light fitting 1 x 20 Watt 220 volt AC decorative box type with driver, holder including LED tub light connecting up with three core flexible copper conductor cable of size from ceiling rose complete all as directed.

S&F of new generation energy saving and environmental friendly long life LED building security light made up of innovative die cast aluminium housing high power LED as lighting source with IP - 66 power consumption 35 watt complete input voltage of 150-240 Volt (nominal rated voltage 240 Volt) complete including twisted 3 core copper cable of size 1.5 Sqmm dia for connecting phase, neutral and earth from ceiling rose to light length as required at site,GI bracket 32 mm dia pipe and 02 numbersclmaps, all fixing arrangements such as fastners, bilts, nuts washers etc all as specified and directed.

Supply and fix electric water heater(Geyser), storage type steel body with copper inner tank and heating element up to 2 KW capacity 25 litre, BEE 5 star rated adjustable temprature setting 0-90 degree C complete with accessories such as safety wall, thermostate, NRV indication lamps, inlet outlet connections,air vent connections, connection pieces including all fixing arrangements such as fastners, bilts, nuts washers etc including making good disturbed wall surfaces matching with the existing surface and finishing complete all as specified and directed by Engr in charge

S&F wire for circuit/sub main wiring with 1100 volts grade double core PVC insulated and unsheathed cable with multistranded copper conductor 6 Sqmm, on surface or recessed or drawn in PVC casing capping/PVC Pi along with 4 Sqmm single core copper conductor multi stranded cable as earth continuity conductor complete all as specified and as directed.(Note: One RM PVC casing capping/PVC conduit ,one run of 4 sqmm earth wire and 2 Run of 6 sqmm cable shall be measured as one run.)

S&F bell/buzzer push modular type modular type 5/6 Amp,flush type complete all as specified & as directed.

S&F call bell ding dong electric AC, 240 volt, 50 HZ, surface type complete all as specified & as directed.

Supply & fixing for One light point controlled by two two-way switch 5/6 Amp complete all as specified and as directed .

Supply & fixing Modular switch 2 way 6A,1 module, 240 Volts complete all as specified & directed.

S&F distribution board vertical type TPN 415 Volt double door IP 43 protection, 4 way with copper bus bars, neutral links , earth link, earthing studs, blanking plates, interconnection between incomer MCCB and bus bar duly prewired fixed flush to wall / other surface with complete all as specified and directed by Engr-in-Charge.

M/S KUNKAPU ENTERPRISES

M/S ASHOK CONSTRUCTION

M/S R N ENTERPRISES

M/S SM ANSARI

M/S NIRMAL TRADERS

M/S SUNRISE CONSTRUCTION AND CO

MS SANGRILA SYNDICATE