GE 861 EWS-44 (T)/2025-26

Amount

Demolition of Plain Cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge.

Demolition of cement reinforced concrete (reinforcement cut as required to facilitate demolition) in ground floors & paving n.exc 15 cm thickness (below or above ground level), complete all as specified and directed by Engineer-in-Charge.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frames with shutter (without taking off shutters from the frames) not exc 1.5 sqm each and removing from site complete all as specified and directed by Engineer-in-Charge.

All as per item No 5 above but exc 1.5 sqm and n.exc 4 sqm complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Dismantling of stone slab and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed by Engineer-in-Charge.

Excavating over areas, n exc 1.5 m deep and getting out in any type of soil complete all as specified and directed by Engineer-in-Charge.

All as per item No 9 above but depth exc 1.5m wide and not exceeding 3.0m complete all as specified and directed by Engineer-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and getting out in any type of soil complete all as specified and directed by Engineer-in-Charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm complete all as specified and directed by Engineer-in-Charge.

M&L for hardcore of broken bricks of gauge n exc. 63mm, deposited, spread and leveled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engineer-in-Charge.

M&L PCC (1:4:8) type D-1, 50 mm thick using 20 mm graded aggregate as in sub base under flooring of path / hardstanding etc complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:4:8 type D-2, (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

M&L PCC (1:3:6) type C-2, (Using 40 mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

M&L PCC (1:4:8) type D-2, 75 mm thick using 40 mm graded aggregate as in sub base complete all as specified and directed by Engineer-in-Charge.

Supply only Integral water proofing compound complete all as specified and directed by Engineer-in-Charge.

M&L for 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors and jointed complete all as specified and directed by Engineer-in-Charge.

M&L for PCC type D2 (using 40mm graded aggregate) in concrete bed to drain pipes including packing under and hunching against the sides of pipes after they are laid and tested for pipes of 150mm bore complete all as specified and directed by Engineer-in-Charge.

M&L for form work to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work n exc 200 mm thick ( Horizontal or sloping) flat rough finished surfaces complete all as specified and directed by Engineer-in-Charge.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in any type of soil complete all as specified and directed by Engineer-in-Charge.

M&L for Hardcore of gauge exc 63mm but n exc. 100 mm, deposited, spread and leveled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed by Engineer-in-Charge.

M&L 25mm thick Damp proof course to horizontal or vertical surfaces including necessary formwork in cement concrete 1:2:4 type B-0 (Using 12.5 mm graded crushed stone aggregate) complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 10mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for three coats of white wash on walls including preparation of plastered or un plastered surface of walls complete all as specified and directed by Engineer-in-Charge.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L for coloured glazed ceramic tiles in vertical 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match tiles including 10mm thick rendering in cement mortar 1:4 on brick walls complete all as specified and directed by Engineer-in-Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing in SSR Part-I complete all as specified and directed by Engineer-in-Charge.

S&F 150mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 150mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engineer-in-Charge.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay complete all as specified and directed by Engineer-in-Charge.

Preparation of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L for applying two coats of synthetic enamel paint on steel Surfaces of any description, over 10cm in width or girth, over red oxide including necessary preparation complete all as specified and directed by Engineer-in-Charge.

S&F 4 mm thick Figured glass, pinhead type in squares n exc 0.5 sqm each pane and glazing with oil putty in squares not exc 0.5 Sqm each pane complete all as specified and directed by Engineer-in-Charge.

S&F PVC valve less, syphonic action type, flushing cistern, low level, 10 ltr capacity coloured with inlet, ball valve, float and handle including brackets complete all as specified and directed by Engineer-in-Charge.

S&F PVC connection 600mm long, 15mm bore size with PTMT nut complete all as specified and directed by Engineer-in-Charge.

S&F square grating 100mm size of PTMT (Minimum weight 50 gms) complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) 75mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) vent cowl of 75mm dia complete all as specified and directed by Engineer-in-Charge.

M&L for 2nd class softwood, as in scantling and similar work, clean sawn, timber fixed in position, complete all as specified and directed by Engineer-in-Charge.

S&F 6mm thick plywood, grade BWR, type BB, fixed in ceiling flat and sloping with nails to timber frame, complete all as specified and directed by Engineer-in-Charge.

S&F framed work such as grills and gratings etc with ends of bars soldered or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, Water staging etc complete all as specified and directed by Engineer-in-Charge.

M&L for mild steel work in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and directed by Engineer-in-Charge.

S&F mild steel framed work as in doors or gate of angle or other section with gusset plates, rails braces, etc complete, drilled for gates of angle or other section fixing of steel sheeting or other covering complete all as specified and directed by Engineer-in-Charge.

S&F Rotational molded polyethylene water storage tanks 500 litre capacity (cylindrical vertical with closed top) three layered, hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed by Engineer-in-Charge.

S&F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 20mm dia PTMT Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm thick plain cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate finished even and smooth without using extra cement as in plinth protection complete all as specified and directed.

S&F 15mm bore fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

S&F water closet vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including provision of cement concrete bedding with P trap 100mm and connection to drain and to flushing pipe, anti-syphonage pipe etc. complete including making good to floor(excluding flushing cistern and flush pipe) complete all as specified and directed by Engineer-in-Charge.

S&F Wash basins, Vitreous China (flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe Vitreous China wash basin, white, flat back, size 630x450mm excluding ditto but including brackets complete all as specified and directed by Engineer-in-Charge.

S&F vitreous china urinal, bowl type (back or corner wall type ) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plug with and long bars screw, pointing around urinal back in cement fixing to flush pipe, grating and union for discharge pipe complete all as specified and directed by Engineer-in-Charge.

M&L reinforced cement concrete 1:2:4 type B-1 (Using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as specified and directed by Engineer-in-Charge.

M&L for reinforced cement concrete 1:2:4 type B-1 (Using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engineer-in-Charge.

M&L for formwork to sides and soffits of floor or roof beams, beam hunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc and fair finished surface also splays between floors and beams, etc complete all as specified and directed by Engineer-in-Charge.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L for 40mm thick PCC 1:2:4 type B-0 (12.5mm graded crushed stone aggregate) as in padding to roof, surface finished even complete all as specified and directed by Engineer-in-Charge.

M&L for mild steel work in hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc. and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed. to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc. and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in surface channel and drains including forms/molds etc., complete all as specified and directed by Engineer-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour and profile having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based Plain sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick or stone walls or concrete surface etc including raking out joints, hacking for key scrubbing down with water complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 20mm thick on stone masonry walls in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15mm thick on fare faces of brick work or concrete surface in cement mortar 1:4 mixed with water proofing compound finished even and smooth without using extra cement complete all as specified Note: Water proofing compound shall be measured and paid separately complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15mm thick on fare faces of brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

S&F second class hard wood plain, solid, straight chowkats and frames wrought, framed rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engineer-in-Charge.

S&F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with MSD square tube etc complete all as specified and directed by Engineer-in-Charge.

M&L for Precast cement concrete 1:2:4, type-B1 (using 20 mm graded crushed stone aggregate) as in landings, cover slabs, chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set and jointed in CM 1:4, complete all as specified and directed by Engineer-in-Charge.

M&L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality conforming to complete all as specified and directed by Engineer-in-Charge.

All as per item no 73 above but 6mm to 10mm dia in stirrups, spacers and binders complete all as specified and directed by Engineer-in-Charge.

S&F 30mm thick flush shutter, solid core construction with block board core and plywood face panels commercial type on both side complete all as specified and directed by Engineer-in-Charge.

S&F factory made solid PVC molded door shutter, 30 mm thick 2mm thick 3D wood grain Moulded PVC sheet polyurethane painted on the front face & 2mm plain colour PVC sheet on back face complete all as specified and directed by Engineer-in-Charge.

S&F Mild steel butt hinges medium weight, cold rolled, 100mm, ISI marked, complete all as specified and directed by Engineer-in-Charge.

S&F barrel tower bolts stove enamelled black of size 200mm complete all as specified and directed by Engineer-in-Charge.

S&F 150mm long (D type) aluminium anodised handles of extruded section (ISI marked) complete all as specified and directed by Engineer-in-Charge.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast-aluminium alloy (ISI marked) complete all as specified and directed by Engineer-in-Charge.

S&F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast-aluminium alloy (ISI marked) complete all as specified and directed by Engineer-in-Charge.

M&L for joint free Non-Skid ceramic coloured tiles 6-7mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including provision of screed bed 15mm thick in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L joint free 600 x 600 mm Non-Skid ceramic coloured tiles 6-7mm thick (square) in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including provision of screed bed 15mm thick in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L for chequered cement concrete tiles glossy finished 30cm x30cmx25mm with grey cement and pigment, set, jointed and pointed in neat cement slurry in floors laid over 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L for Plain cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork, complete all as specified and directed by Engineer-in-Charge.

M&L for Plain cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork, complete all as specified and directed by Engineer-in-Charge.

Taking up or down 15mm bore steel water tubing & connections, including cleaning for refixing or offering credit as per schedule of credit complete all as specified and directed by Engineer-in-Charge.

All as per item No 88 above but 20mm bore complete all as specified and directed by Engineer-in-Charge.

S&F 15mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

S&F 20mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

Refixing 15mm bore old steel water tubing & connection in new or old position of wall, ceiling, floor etc complete all as specified and directed by Engineer-in-Charge.

All as per item No 92 above but 20mm bore complete all as specified and directed by Engineer-in-Charge.

S&F in repair 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/ floors (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/ floors (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F in repair 110mm (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F in repair 75mm PVC (SWR) bend any radius (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F 75mm PVC (SWR) bend any radius (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F in repair 110mm PVC (SWR) bend any radius (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F 110mm PVC (SWR) bend any radius (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F in repair 75mm PVC (SWR) junction single (Single T) equal or unequal (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

All as per item No 101 above but 110mm bore of pipe (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including 'P' or 'S' trap, seat cover and fixing bolts, flushing cistern and flush pipe & making good to floor in cement mortar M-15 (1:2:4) type B-1 (using 20mm graded crushed stone aggregated), complete all as specified and directed by Engineer-in-Charge.

S&F in repair 10 ltr capacity PVC valve less , symphonic action type flushing cistern, low level, white, with inlet ball valve, float and handle including bracket and 32mm dia flush pipe of polyethylene of low or high density for low level cistern complete all as specified and directed by Engineer-in-Charge.

S&F 10 ltr capacity PVC valve less , symphonic action type flushing cistern, low level, white, with inlet ball valve, float and handle including bracket and 32mm dia flush pipe of polyethylene of low or high density for low level cistern complete all as specified and directed by Engineer-in-Charge.

S&F PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed by Engineer-in-Charge.

S&F vitreous china wash hand basin, white flat back of size 630x450mm including 15mm dia CP pillar tap, PVC waste coupling 32mm, chain and plug and PVC waste pipe, PVC connection 45cm long including CI brackets/fixing with fasteners etc complete all as specified and directed by Engineer-in-Charge.

S & F in repair 15mm bore pillar tap cast copper alloy with capstan head, chromium plated, screw down high pressure, with or without lettered hot or cold with long screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repair 15mm fancy type bib tap, chromium plated with crutch or butterfly handle, screwed down , screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge.

S&F 15mm fancy type bib tap, chromium plated with crutch or butterfly handle, screwed down , screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge.

S&F in repair 15mm dia stop valve/ angle valve chromium fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and directed by Engineer-in-Charge.

S&F 15mm dia stop valve/ angle valve chromium fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and directed by Engineer-in-Charge.

M&L preparing newly plastered surfaces of wall and applying two coats of oil bound distemper over one coat primer on walls over thin layer of wall putty complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered or un plastered surfaces on wall surfaces and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed by Engineer-in-Charge.

M&L for painting to steel surfaces of any description over 10 cm width or girth including preparation of new or untreated surfaces and applying with two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

M&L for Preparation of old painted GI/steel surfaces of any description not otherwise described over 10cm width or girth as in roof and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

S&F in repair 75mm PVC(SWR) floor trap with grating including jointing with solvent cement (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F 75mm PVC(SWR) floor trap with grating including jointing with solvent cement (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F in repair PVC (SWR) 'P' trap 110mm (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F 500 Ltrs capacity rotational molded polyethylene water storage tanks(cylindrical vertical with closed top) three layered hoisted and fixed in position all as specified and directed in SSR Part-I including dismantling existing water tanks and removing to store complete all as specified and directed by Engineer-in-Charge.

S&F 20mm ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

S&F Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed by Engineer-in-Charge.

S&F in repairs stainless steel Soap Dish complete all as specified and directed.

S&F in repairs glass corner shelf complete all as specified and directed by Engineer-in-Charge.

S&F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed by Engineer-in-Charge.

M&L in repairs for weather boarding in 2nd class softwood clean swan, plain, 20 mm thick or feather edges, 15 mm to 20 mm the and fixed with 30 mm laps joints complete all as specified and directed by Engineer-in-Charge.

Demolition of Plain Cement Concrete in ground floor and paving not exc 15cm thick (below or above) ground level complete all as specified and directed by Engineer-in-Charge.

Dismantling wall and ceiling boards (fiber, Pulp, insulation etc) or insulation board/slabs/blankets, any thickness, including cover fillets & snap grid frame etc, complete all as specified and directed by Engineer-in-Charge.

M&L for joint free 600 x 600 mm Non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) in each floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L 2nd class soft wood plain fillets square/rectangular or triangular in section of sectional area exc 13 Sqcm but n exc 25 Sqcm splayed chamfered or rounded on one edge or face complete all as specified and directed by Engineer-in-Charge.

M&L for plywood, 6mm thick grade BWR, type BB, fixed with screws to timber framework complete all as specified and directed by Engineer-in-Charge.

M&L for 2nd class soft wood plain fillets square/rectangular or triangular in section of sectional area exc 03 Sqcm but n exc 6 Sqcm splayed chamfered or rounded on one edge or face complete all as specified and directed by Engineer-in-Charge.

M&L for 2nd class soft wood plain fillets square/rectangular or triangular in section of sectional area n.exc 03 Sqcm splayed chamfered or rounded on one edge or face complete all as specified and directed by Engineer-in-Charge.

S&F 35mm thick, 2nd class softwood factory made, plain framed, panelled shutters (any no of panels panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneers on both faces. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified and directed by Engineer-in-Charge.

S&F 35mm thick, 2nd class softwood factory made glazed and skeleton shutters, open rebated and prepared to receive glass or gauge, etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitered beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (a) for door shutter supplying and fitted to chowkats, complete all as specified and directed by Engineer-in-Charge.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and width of aperture 1.18mm & fixed with tinned tacks or galvanised wire staples complete all as specified and directed by Engineer-in-Charge.

S&F 3mm thick figured glass, pin headed type and glazing with oil putty or wooden beads in square n.exc 0.5 sqm each pane complete all as specified and directed by Engineer-in-Charge.

S&F 150mm long mild steel barrel tower bolts, stove enameled black, with bright bolts fixed, complete all as specified and directed by Engineer-in-Charge.

S&F 150mm long, mild steel pressed handles, oval type, stove enamelled black, complete all as specified and directed by Engineer-in-Charge.

S&F 250mm size mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed by Engineer-in-Charge.

S&F 100mm long mild steel barrel tower bolts, stove enameled black, with bright bolts fixed complete all as specified and directed by Engineer-in-Charge.

S&F 75mm long, mild steel pressed handles, oval type, stove enameled black complete all as specified and directed by Engineer-in-Charge.

S&F 75mm long, mild steel cold rolled butt hinges, medium weight complete all as specified and directed by Engineer-in-Charge.

S&F in repairs brass Hat and coat hooks, solid body, 175mm to 250 mm complete all as specified and as directed

M&L for Preparation of old painted wooden surfaces over 10 cm width or girth and applying One coats of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

S&F in repairs CP Curtain Rod/ drapery rod 25mm dia Decorative type with a pair of brackets for each curtain unit, powder coated of approved pattern and colour complete all as specified and directed by Engineer-in-Charge.

Supply and fix air termination single pointed aluminium rod not less than 12mm dia and 300mm long including fixing of GI base on epoxy insulators of suitable size to isolate from the roof and fixing of insulators on roof over the purlin using self tapping screws of suitable length or other means to make the roof leakage proof for fixing of air terminal rod and connecting with down/roof conductors complete all as specified and directed by Engineer-in-Charge.

M&L for Plain cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in bed blocks/PCC Blocks and the like (size 200x200x200mm) complete all as specified and directed by Engineer-in-Charge.

Supply and fix aluminium strip of size 25x3.15 mm including epoxy/porcelain insulators of suitable size, distance between insulators not more than 1 mtr including fixing screws washers etc complete for PCC block of size 200x200x200mm including cost of PCC block for RCC roof, using screws, washers, gutti/rawal plugs etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for test point terminal block made of gun metal or phosphorus bronze size 75 x 75 x 25 mm drilled and screw end connected to existing Aluminium/GI strips complete including 3 nos. 8 mm dia 25 mm long hex. head screw complete and including fixing of test point with sheet metal enclosure on insulators to isolate from the walls, fixing of insulators on wall using suitable size of screws, washers, gutti/rawal plugs etc, including making good to disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

Supply and fix GI pipe light grade including provision of all fittings laid in pavement, road crossing and soil complete of size 40mm dia for protection of GI strip complete all as specified and directed by Engineer-in-Charge.

Earthing complete with copper earth plate electrode of size 600 mm x 600 mm x 3.15 mm thick buried directly to ground vertically to a depth not less than 2.25 Mtr below the ground level with top edge of earth plate not less than 1.65 Mtr below normal ground level connected to 20 x 3mm copper strip and earthing lead protected with 50 mm dia GI pipe light grade filling around with charcoal dust and salt including excavation, returning, filling of earth and disposal of surplus soil to a distance not exceeding 50 mtr and connected to GI strip by means of GI nuts, bolts and washers strip connected to earth plate including chamber PCC 1 : 3 : 6 type C1. using 20 mm graded stone aggregate in concrete pit pre-cast RCC 40 mm thick reinforced with 6 mm dia round at the rate of 75 mm C/C both way with 12 mm dia mild steel plain bar lifting handle 2 Nos funnel with wire mesh 20 mm dia GI pipe light grade watering pipe and frame work complete all as shown in electrical plate No. 3 of SSR Part - I 2009 including testing complete all as specified and directed by Engineer-in-Charge. (20x3mm copper earth strip upto 7.5 m length in included in unit rate quoted by contractor and beyond this length the same shall be measured & paid separately).

Taking down carefully aluminium/copper point wiring (light fan socket or power) complete with fitting such as switches, tube lights, ceiling rose, pendants, regulators, and making good disturbed surfaces of walls, floor to match with existing and keeping items aside in safe custody for reuse such as regulators, light fitting, MCBs complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring for one light point/fan point controlled by one switch with 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green colour) as earth lead in and including PVC casing and capping medium grade of suitable size run on wall/surface with all fittings (ISI Marked) controlled by one switch including CI/MS/ wooden sunk box of required size, & as directed by Engr in Charge & 3mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified and directed by Engineer-in-Charge.

All as per srl item No-148 here in above but for One 3 pin socket outlet, 5 Amps, independent, with cables 1.5 sq. mm size complete all as specified and directed by Engineer-in-Charge.

All as per srl item No-148 here in above but for One 3 pin socket outlet, 5 Amps on the same board with other switches, with cables 1.5 sq. mm size complete all as specified and directed by Engineer-in-Charge.

All as per srl item No-148 here in above but for 3 pin socket outlet 15 Amps independent board with 2.5 Sqmm complete all as specified and directed by Engineer-in-Charge.

S&F switch piano flush type, 06 Amps single pole, one way complete all as specified and directed by Engineer-in-Charge.

S&F Switch socket combination 2 in 1, 3 pin, 5 Amp flush type universal 240 Volts complete all as specified and directed by Engineer-in-Charge.

S&F Switch socket combination 2 in 1, 3 pin, 5/15 Amp flush type universal 240 Volts complete all as specified and directed by Engineer-in-Charge.

Supply & fixing of ceiling rose, 3 phase/PVC/polycarbonate isolated body complete all as specified and directed by Engineer-in-Charge.

Supply & fixing lamp holder (Angular / Straight), insulated body, with back plate for batten fitting complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED lamp 10 W complete all as specified and directed by Engineer-in-Charge.

S&F decorative ultra slim linear LED 20 Watt 4' long lighting fixture with extruded al heat sink, environment friendly, energy efficient ready to use pack including LED tube complete with inbuilt electronic driver, PCB, connector block etc. including connecting up three copper flexible cable from ceiling rose to fittings including connecting up and fixed on including two nos PVC square box of required size complete all as specified and directed by Engineer-in-Charge.

S&F in repair sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 4 way, with 200 Amps rated copper bus bar and IP - 43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

S&F in repair sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 8 way, with 200 Amps rated copper bus bar and IP - 43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

S&F in repair MCB, SP, AC, 240 volts "B" series capacity of 06 to 32 Amps, 10kA and making connections complete all as specified and directed by Engineer-in-Charge.

S&F in repair MCB, SPN (single pole neutral), AC, 240 volts, B series capacity 32 Amps 10kA and making connections complete all as specified and directed by Engineer-in-Charge.

Material & labour in replacement for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No.3 of SSR part I connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm center to center both way with suitable lifting handle and pit / chamber in PCC 1:3:6 type C1 , Angle iron 40x40x5mm frame for pit cover including testing on completion complete all as specified and directed by Engineer-in-Charge.

S&F in repair 1100 volts grade service cable with PVC insulated aluminium conductor 16 Sqmm nominal cross section 2 core complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing exhaust fan 300 mm sweep PVC body with louver, 240 volts AC single phase, 50 Hz, ISI marked, including necessary work in wall/sheet, including connection cable, nut bolt and other fixing material complete all as specified and directed by Engineer-in-Charge.

Supply and laying or fixing or passing through pipe or binding with fencing/pole etc, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armored with galvanised steel wire or tape and overall PVC sheathed 10 Sqmm nominal cross section 2 core solid conductor complete all as specified and directed by Engineer-in-Charge.

Supply and laying Galvanized iron pipe medium grade 20 mm size laid in floor/wall and the like including all accessories complete all as specified and directed by Engineer-in-Charge.

Supply and fixing gun metal gate/globe valve 20 mm screwed both endes complete all as specified and directed by Engineer-in-Charge.

M&L for Cutting existing CI/GI pipe line of 20 mm to 50 mm dia and inserting 'T' and taping new connection with all accessories complete all as specified and directed by Engineer-in-Charge.

M&L lagging for the 20mm GI tubing in external water supply of plumbing all around with 25mm thick bonded mineral wool pre-formed. SNAPON pipe section of density 144 Kg/Cum conforming to IS-9842 or equivalent and provided chicken wire mesh netting 25gauge 20mm meshing and plaster of paris 3 to 5 mm thick all around the mesh after breaking old unsv/ broken lagging complete all as specified and directed by Engineer-in-Charge.

Supply and fixing stepped type electronic fan regulator flush type on the existing sheet etc AC 230 Volts, duly ISI marked with and including connector complete all as specified and directed by Engineer-in-Charge.

M/S Manzoor Constructions (BID ID -3480072)

M/S SHEIKH FEROOZ AHMAD (BID ID -3478585)

ALI HAMZA ENTERPRISES (BID ID -3474025)