Construction of State Data and Training Centre and Water Quality Lab for both Surface Water and Ground Water under National Hydrology Project

Amount

Earth Work:

Earthwork in excavation in foundation trenches in ordinary soil (vide classfication of soil item - A) and disposal of excavated earth as obtained to a distance upto 50 m including all lifts, levelling, ramming the foundation trenches, removing roots of trees shurbs all complete as per approved design building specification and direction of E/I. Extra for earth work in hard soil as per specification and direction of E/I. (vide classfication of soil item - B)

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).

Providing coarse clean sand in filling in foundation trenches or plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts includng cost of all materials, Labour, rotalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume).

Providing designation 75 A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth

Providing 250mm. wide brick drain in cement mortar (1:6) with av. 250mm. clear depth and 250mm. apron including cost of earthwork involved with 75 mm. ~ cement concrete (1:4:8) over one brick designation 75A flat soling in proper grade and slope at the base, the drain duly plastered in C.M.(1:3) with punning over exposed surface all complete as per building specification and direction of E/l.

Plain/Reinfoeced Cement Concrete in open foundation complete as per drawing and technical specifications

P.C.C Grade M15(1:2;4)

Using Concrete Mixer

Plain/Reinfoeced Cement Concrete in sub-structure complete as per drawing and technical specifications

Ht, upto 5m

R.C.C Grade M20.

Using Concrete mixer

Furnishng & Placing reinforced Cement concrete in super structure as per drawing and technical specification

RCC M20 Grade

Using Concrete Mixer

For T Beam & Slab

Ht upto 5m

Ht upto 5m to 10m

Ht above 10m

Providing designation 75 A brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 75B work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.m. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials ranking out joints to 15mm depth, curing taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 125 mm thick reinforced designation 75 A brick work in C.M (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials , scafolding, raking out joints to 15 mm depth, curing, taxes and royalty ( but excluding the cost of reinforcement) all complete as per building specification and direction of E/l.

Providing designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9" x 4.5" x 3") in C.M. (1:6) in superstructure with approved quality of clean sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. ON 10" Th. Brick work

Extra for brick work for each consecutive floor above first floor including watering and scafolding, all complete as per direction of E/l.

Providing Designation 100A 112 mm thick reinforced B/W with Fly Ash Lime Brick (FALB) conforming to IS 12894-1990 (9"x4.5"x3") in cement mortar (1:4) in Superstructure with clean coarse sand of F.M. 2 to 2.5 including the cost of screening, raking out joints to 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Supplying fitting and placing un coated HYSD bar reinforcement in foundation complete s per drawing and technical specification

Supplying fitting and placing un coated HYSD bar reinforcement in sub structure complete s per drawing and technical specification

Supplying fitting and placing un coated HYSD bar reinforcement in super structure complete s per drawing and technical specification

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Extra for plaster work over exterior surface for each consecutive floor above first floor including cost of scaffolding etc. all complete as per direction of E/l.

Providing 6mm Thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/l.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/l.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:

New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600x600 mm

Size of Tile 800x800 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600x600 mm

Size of Tile 800x800 mm

Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge.

In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand)

Acid and alkali resistant tile

In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand)

Acid and alkali resistant tile

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite of any colour and shade

Area of slab over 0.50 sqm

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.

Granite Stone of approved shade

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent

Extra for marble stone flooring in treads of steps and risers using single length up to 2.00 metre

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge

Granite work

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness,including hinges, jamb, lock jamb, bead and if required angle threshold ofmild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressedmild steel welded or rigidly fixed together by mechanical means, includingM.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplateand shock absorbers as specified and applying a coat of approved steelprimer after pre-treatment of the surface as directed by Engineerin-charge:

Profile C

Fixing with adjustable lugs with split end tail to each jamb

Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with one sides teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Supplying, fitting and fixing 30mm thick solid core type decorative single leaf flush door shutter with one sides teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Twin rubber stopper

Providing and Fixing factory made UPVC door frame, made of UPVC exturded sections, of size 65 mm x 55 mm with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge sidevertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer's specification and direction of Engineer-in-charge.

Providing and fixing 37 mm thick factory made PVC door shutter, styles and rails made of PVC hollow section of size 100 mm x 37 mm with wall thickness 2 mm (± 0.2 mm), with inbuilt bead on one side, styles and rails mitered cut and joint at the corners by means of 2 nos of plastic brackets of size 75 mm x 220 mm at each corner and stainless steel screws, reinforcing the hinge side of style by inserting PVC profile of size 28 mm x 30 mm, with wall thickness 2 mm ( ± 0.2 mm). Lockrail of size 100 mm x 37 mm, wall thickness 2 mm (+ 0.2 mm) will be fixed to the vertical styles. Providing with PVC snapfit beads and panel of size 100 mm x 20 mm, and inserting 2 nos tie bar of 6 mm dia and fastening with nuts and washers complete, all as per manufacturer's specification and direction of Engineer-in-charge.

Non decorative finish (matt finish)

Supplying, fitting and fixing aluminium fittings of approved quality and make to doors and windows all complete as per building specification and direction of E/l.

150mm tower bolt

100mm door handle with plate.

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete

Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately).

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge.

Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/m2) duly filled FR insulation material and Fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge (panneling to be paid for separately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 m/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant rimer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and s per direction of Engineer-in-charge with glass of required thickness having 60 minutes of fire resistance both integrity & radiation control (EW60) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a). First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. b)Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.(The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.)

Supplying, fitting and fixing callapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2 mm at 100mm. centres and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40x40x6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles, including applying a priming coat of red lead paint, carriage , hoisting and taxes all complete as per building specification and direction of E/l.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.

80x1.20 mm M.S. laths with 1.20 mm thick top cover

Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll

forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC xtruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel ulti point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc.

Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately).

Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 2.50 sqm upto 4.00 sqm.)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size ccording to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and ecessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc.

Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made

Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm).

Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) truded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC rofile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc.

After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately).

Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540- F & ISO 11600

Upto 5 mm depth and 5 mm width

Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.)

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete :

20 mm dia

Providing & fixing Fan hook of 16 mm. dia. M.S. bar 1 Mtr. Long bent to required size and shape, placed in position and fixed in Truss Frame / RCC Slab / beam at the time of casting all complete as per building specification and direction of E/I. (Where materials is not supplied by deptt.)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing rust , dirt, , scales , smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/l. ( Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specification)

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/ 450N/ 5cm. Tear strength in longitudinal and transverse direction as 300/ 250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :

3 mm thick

Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100% polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation.

Grading roof for water proofing treatment with

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline lurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

Water Tank

For vertical surface two coats @ 0.70 kg per sqm

For horizontal surface one coat @1.10 kg per sqm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with sea; ring conforming to IS:5382, leaving 10mm gap for thermal expansion, Single socketed pipes - 110 mm Rain water pipe

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler - 110mm

Bend - 110mm

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm ntre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction,

including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitablym fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)

12.5 mm thick tapered edge gypsum moisture resistant board

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm)

i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.

With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles

Providing fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Fibre glass wool conforming to IS : 8183, density 24kg / m3, 50mm thick, wrapped in 200 G Virgin Polythene bags, fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling of building.

Providing and fixing toilet paper holder

C.P. brass

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other ections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing anodised aluminium (anodised transparent or. dyed to required shade according to IS: 1868. Minimum anodic coating of grade AC 15) sub frame work for windows and ventilators with extruded built up standard tubular sections of approved make conforming to IS: 733 and IS: 1285, fixed ith dash fastener of required dia and size (Dash fastener to be paid for separately)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin-charge.

Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural rawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Providing and fixing Plane Glass pane in existing windows and ventilators as per E/I

Pin hammered Glass- 4 MM TH.

Providing and fixing Fly proof netting (18 gauge wire with 12-16 nos, mesh per qm)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with ouble spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power ressed/ roll form G.I. sheet with zinc coating of 120 gms/ sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon

plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, .Galvanised M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each with zinc coating of 120 gms/sqm(both side inclusive)) to be provided at the horizontal joints of two

boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.

75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board conforming to IS: 2095: (part 3) : 1996 (Board with BIS certification marks)

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as er grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear ortions of the building for all heights and all levels, including:

Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional ovement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.

Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and anufacture, as per the approved sealant design, within and all around the perimeter for holding glass.

Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight

Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge.

The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled orking structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight tructural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the pproved shop drawings and as directed by the Engineer- in-Charge.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin roof stainless steel wire mesh shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places

Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories ccreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately

The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or by any other accreditation body which operates in accordance with ISO / IEC 17011 and accredits labs as per ISO/ IEC 17025.

Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr

Static Water Penetration Test. (50pa to 1500p) as per ASTME- 331-09 testing method for a range up to 2000 ml.

Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml

Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm

Seismic Movement Test (upto 30 mm) as per AAMA 501.4- 09 testing method for Qualitative test, Tests to beconducted on site.

Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor

(Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2)

For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.

Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having roperties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin- Charge.

Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic float glass of approved colour and shade with reflective soft coating on urface # 2 of approved colour and shade so as to match the colour and shade of the IGUs in the vision panels etc. ,all complete for the required performances as specified, as per the Architectural drawings, as per the approved shop drawings, as specified, and as directed by the Engineer- in- Charge.

For payment, only the actual area of glass on face # 1 of the glass panels (but excluding the area of grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (Payment for fixing of Spandrel Glass Panels in the curtain glazing is included in cost of relevent Item*).“(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 K etc. . The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Supplying chemical emulsion in sealed containers including delivery as specified.

Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor

With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Labour for, laying, fitting and fixing NP2 R.C.C. spun pipe with collars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leak proof including providing sight rails, bonning rod, night guard, red light and barriers etc. All complete as per specification and direction of E/I.

150mm dia R.C.C. spun pipe Upto 3.0 metre depth of invert below G.L.

NP2 RCC hume pipe with collar as per I.S.S 458-1971- 150MM DIA

Supplying materials and labours for constructing inspection chamber of designated class 75B bricks size 750mm deep, 600 x 450mm internal dimension having 250mm wall thickness in cement mortar ( 1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600 x 475mm G.I. Cover with frame (weight not less than 36Kg) alongwith earthwork in excavation and 88mm thick P.C.C. (1:3:6) in foundation and refilling all as per specification and direction of E/I.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge -100 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge

Supplying, filling, spreading & leveling gravels of size range 5 mm to10 mm, in the recharge pit, over the existing layer of boulders, inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mmto 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge

Basic rates for 115/125mm dia Drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with D.I. rings all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 115/125mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work including contractor profit & O.H. Charges as per specification and direction of Engineer-In-charge for the year 2015-2016 Drilling upto 30 mtr. Depth below G.L. in Urban Area

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 5 HP

Supply fitting and fixing of standered make starter pannel Board with arrangement of all necsssury protection including all taxes ,royalty etc all complete job as per direction of E/I.

Supplying fitting and fixing 3core 4 sqmm flat copper submersible cable Finolex/havells make including all taxes, royalty etc. all complete job as per direction of E/I

Supply fitting and fixing G.I pipe (Tata Make) or equivalent as per I.S 1239 ISI marked , medium quality , 50 mm dia

Excavtion in soil using hydaulic excavator CK 90 and tippers with disposal upto 1000 meters (excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers,trimming bottom and side slopes,in accordance with requirements of lines, grade and cross sections, and transporting to the embankment location within all liftsand lead upto 1000 m) ii)Including royalty @ Rs. 30.00 per cum , cost of watering, rolling & compaction.

Compacting original ground. CASE ii- Compacting original ground supporting embankment . i) Rolling with vibratory roller

Granular sub-base with close graded material (Table :- 400-1) - B.By mix in place method (construction of granular sub-base by providing close graded material,sprending in uniform layers with mortor grader on prepared surface ,mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density,complete as per clause 401. ii) for grading - II Material

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). 450MMX300MMX150MM

Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared.

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Rough dressing the trenched ground including breaking clods.

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.

Fine dressing of the ground

Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in 499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area.(two application) i/c cost of chemical)and as per direction of officer-in-charge.and as per direction of officer-in-charge

Supplying and stacking of good earth at site including royalty and carriage up to 1 km (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage up to 1 km (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 20 mm

Spreading of sludge, dump manure and / or good earth in required thickness as per direction of Officer-in-charge (Cost of sludge, dump manure and / or good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge..

Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge.

Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge

Providing and stacking of Murraya exotica of height 45-60 cm. in poly bags of size 15 cm as per direction of the officer-in-charge

Providing and stacking of Cuphea chinensis of ht. 20-30 cm full of branches and healthy foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Chandni dwarf of height 15-20 cm., well branched in earthen pots of size 20 cm as per direction of the officer-in-charge. s per direction of the officer-in-charge

Providing and stacking of Alpinia Variegated (three in one) having ht. 30 cm and above, with fresh and healthy variegated foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge

Providing and stacking of Aspidistra, having 10 to 15 leaves well developed with fresh & healthy in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge

Providing and stacking of Daniella variegated, with 3 to 4 variegated leaves in 20 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Ophiopogon, Green/Black full of leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge

Providing and stacking of Foxtail palm of ht. 120-150 cm bottom girth 15- 20 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge

Providing and stacking of Ficus benjamina (green) of height 120-135 cm. with 6-8 branches and lush green foliage in g. bags of size 25 cm as per direction of the officer-in-charge

Providing and stacking of Bottle palm of ht. 150-180 cm bottom girth 20-25 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge

Providing and displaying of Areca Palm having ht. 90 cm to 1.20 m with 4 to 5 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and Displaying Cycus revoluta specimen , having 45 to 50 fresh and healthy, leaves having 30cm to 35cm circumfrance of base stem well developed in 40 cm challi, as per direction of the officer-in-charge

Providing and Displaying Bird of paradise well developed with fresh & healthy 90 to 120 cm ht in 30 cm Earthen Pot/ Plastic Pot as per direction of the officer-in-charge.

Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.v

Providing and stacking of Alstonia scholaris of height 150-165 cm. in bag of size 25 cm as per direction of the officer-in-charge

Providing and stacking of Michelia champa (Golden Champa) of height 90- 105 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge

Providing and stacking of Bauhinia purpurea (Kachnar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge

Providing and stacking of Polyalthia longifolia (Ashok) of height 150-165 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge

Providing and stacking of Saraca indica (Sita Ashok) of height 105-120 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately)

Holes 60 cm dia, and 60 cm deep

Holes 45 cm dia, and 45 cm deep.

Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, edge, flower beds, foliages, creepers etc. ncluding hoeing,weeding, pruning, replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, pplying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide will be provided by the Department & lawn mover and brush cutter with fuel and other T & P material/articles shall be provided by the contractor.) and as per direction of officer in charge. FOR 6 MONTH

Design and construction RCC ground service reservoirs / RCC Sump in M-300 mix of required capacity including excavation in all type of strata foundation concrete, container wall, bottom slab top RCC roof slab or dome , 20mm th. C.M plaster with waterproofing compound in C.M 1:3 proportion to inside face of the container, including epoxy paint from inside including refilling and disposing of surpulus stuff within lead of 50 m, all labour and material charges, for laying and jointing of pipe assembly for inlet, outlet washout, over flow and bye passarrangement consisting of C.I/M.S. D/Fpipes, special and valvesof given diameters, providing and fixing accessories such as M.S ladder inside and outside, C.I Manhole frameand cover, water topslab, B.B masonry chamber for all valves, ventilating shafts including giving satisfactoryhydraulic test and water tightness test as per IS code and providing three coat of cement paints to all expose surface of structure including roof surface, etc. complete as per design data criteria, obligatory requirements and detailed specifications.

Anti termite treatment shall be given for underground portion of the structure.

1. The design shall be in accordance with various relevant IS specification (IS 456/2000, IS875-1987,IS3370-1965 or revised) 2. Only MS bar grade I confirming to is 432 part I or high yield strength deformed bars confirming to IS 1786 OR IS 1139 shall be used. Grade II MS bars shall not be used. 3. Entire structure shall be in M-300 only 4. The scope of pipe assembly work shall be upto 5metre beyond out sid face of the wall, cost of pipes valves and specials is not included in the rate but labour cost for laying and jointing is included 6. The job includes designing the structure for up lift pressure and dewatering if required during entire execution and disposal of surplus excavated stuff within lead of 50 mtrs as directed by E/I . If up lift considered in design the these rates shall be increased by 7.5% 7.G.S.R outlets shall be with bell mouth of approved pattern in bottom slab and cost of designing bell mouth is included in the rates. Sump well includes cost of suction pit required at bottom

8. For pipe diameters upto 300 mm only CI pipe and CI specials shall be used . For pipe diameters above 300 mm , MS pipes and specials minimum 10mm thick shall be used wth proper anti corrosive epoxy treatment from inside and outside. 10. Above rates applicable for Seismic Zone 2,3 and 4 75% part rate shall be paybale for reinforcement, concrete and plastering items of all type of G.S.R and sump still satisfactory hydraulic testing for water tightness test ig given and till that work shall be treated as incomplete. 12. 105 SHALL BE ADDED FOR SUMP IF OVER HEAD PUMP HOUSE IS PROPOSED

Cost of 1,00,000 litres capacity

Carriage of Material

Bricks Lead =1K+7P km

Sand lead = 10 km

Stone chips lead = 50 km

Stone metal lead = 50 km

PLUMBING & SANITORY WORKS

Supplying, fitting and fixing 40mm high vitreous white glazed ware E.W.C. with "p" trap of parry/hindustan or any other approved I.S.S. make including supplying and fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make and complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle cock of approved qualty weight not less than 450grams 15mm P.V.C. alkathene pipe 45cm. long with brass coupling at both ends and White/black plastic solid state seal and lead of commander/cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide prining, all complete as per specification and direction of E/I. (i)With s trap B) 12.5 lit. low level P.V.C cistern

Supplying fitting and fixing viterous white glazed earthen ware IWC of parry hindustan any other ISS approved make with 100mm HCI p trap 15 ltr CI pull and let go flushing cistern of names or other ISS equivalent make complete with all fittings CI or C C bracket 32mm alkethene / PVC telescopic flush pipe about 2m long with one brss coupling and clamps GI chain and pull including supplying and fixing a pair of vitreous white glazed earthenware footrest to be fixed in floor 15mm CI body brass spindle stop cock of weight not less than 50 grams 15mm PVC connection pipe 450mm long and coat of red oxide primer etc. all complete as per specification and direction of E/I. A) 580 mm long c. With 12.5 ltr low level PVC cistrn

Supplying fitting and fixing flat back or angular lipped front vitreous white glazed ware urinal of hisdustan parry or any other approved ISS approved make with all fittings with CI or RS brackets standard size GI flush pipe with fittings clamps 15mm CI body brass spindle stop cock of approved quality weight not less than 400 gms 15mm PVC alkethene pipe 450mm long with brass coupling at both ends and dooing plumber points including painting of exposed part with two coats of approved paint over a priming coat of red oxide cutting wall and floor making good the same etc. all complete as per specification and direction of E/I. A)Flat back or standing corner. (600 x 350mm)

Providing and fixing PTMT urinal cock of approved quality and colour. 15 mm nominal bore, 80 mm long, 42 mm high and 30mm wide with BSP female threads weighing not less than 48 gms

Supplying, fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S approved make supported on painted C.I. or R.S. brackets 32mm C.I. brass waste, 15mm dia C.I. body spindle stop cock of approved quality of weight not less than 350grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

75 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler

Single Tee with door

Single tee without door

Bend 87.5 degree

75 mm bend

110mm bend

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Providing and fixing 15mm dia and 45cm long PVC connection pipe with heavy quality brass coupling at both ends etc all complete as per specification and direction of E/I

Supplying and fixing H.C.I. fittings of approved make confirming to I.S.S. 1729 including supplying nails and bobines lead and yarn from making lead caulked joints including earthwork or providing scaffolding as the case may be all complete as per specification and direction of E/I. J(j) floor trap with grantings 100 mm dia

Cutting chajjas or concrete for laying PVC Pipe and restoring the same with RCC (1:2:4) brick work in cement mortar (1:4) and cement plaster 1:4 as er specification and direction of E/I

Making holes in walls for PVC Pipe and restoring the same after pipe laying (b)

125 mm thick

250mm thick wall

Supplying fitting and fixing C.P bathroom fittings of approved make and as per IS specification all cost complete as per direction of E/I (all rates have been adopted from basic rate from SOR + 10% for labour and contactors profit

Pillar cock (long neck)

Bib cock (long thread)

Angular stop cock L.T.

32mm dia PVC waste pipe 750 mm long with coupling

15 mm CP nipple with coupling

Steel jali-100mm dia

Wall mixer 3 in 1 system with provision for over head shower with elbow coupling and wall flange

S/F/F white glazed fire’s clay/ steel sink of approved make with over flow arrangements supported on C.I. or R. S. painted brackets 40 mm dia C.O. brass waste with C.P. brass chain and rubber plug, 40 mm dia PVC waste pipe about 750 mm long with brass coupling at one end and 15 mm C.I. body brass spindle bib cock of approved quality of weight not less than 450 grams including cutting wall and making good the same etc. all complete as per specification and direction of E/I. Kitchen sink 600 mm x 450 mm x 250 mm

Kitchen Sink (600mmX450mmX250MM)

LAB SINK 450MMX300MMX150MM

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I.

Glass Shelf with C.P. brass rail

600x125mm glass shelf complete

Mirror of 6mm thick plain glass beveled edge mirror including C.P. brass revolving fitting 3mm plywood board and C.P. hinges to fix with mirror.

600 mm x 450 mm size

C.P Brass towel rail 20mm x 600mm with bracket container

CP Brass dish container medium quality with screw and hinges etc.

CP Brass liquid soap container

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This ncludes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge

External work

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

50 mm nominal outer dia Pipes

62.50 mm nominal inner dia Pipes

Providing and fixing G.M. non return valve Horizontal / vertical type of approved quality as per specification and direction of E/l.

Horizontal- 25 MM

15 MM DIA WEIGHT NOT LESS than 150gms

32 mm dia

50mm dia

Vertical - 25 MM

32 mm dia

50 mm dia

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI :12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing N.P./ C.P. brass/ P.V.C. porcelain shower rose of 15 mm inlet etc. all complete as per specification and direction of Engineer- in – Charge. (a) 100 mm dia C.P. Shower

Earth work in excavation for laying of different types and sizes of R.C.C. spun pipes with disposal of excavated earth within initial lead and lift as per specification and direction of E/l. (a) For classification of soil item- A

Earth work in back filling the trench after laying different types and sizes of R.C.C spun pipes with earth removed during excavation within initial lead and lift as per specification and direction of E/I 80X0.45X0.6

NP2 RCC hume pipe with collar as per I.S.S 458-1971 150MM DIA

Labour for, laying, fitting and fixing NP2 R.C.C. spun pipe with collars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leak proof including providing sight rails, bonning rod, night guard, red light and barriers etc. All complete as per specification and direction of E/I. 150mm dia R.C.C. spun pipe Upto 3.0 metre depth of invert below G.L.

Supplying materials and labours for constructing inspection chamber of designated class 75B bricks size 750mm deep, 600 x 450mm internal dimension having 250mm wall thickness in cement mortar ( 1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600 x 475mm G.I. Cover with frame (weight not less than 36Kg) alongwith earthwork in excavation and 88mm thick P.C.C. (1:3:6) in foundation and refilling all as per specification and direction of E/I.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with brick and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

ELECTRICAL WORKS

Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required.

Group-A

Group-C

Twin Control Point Wiring in PVC Conduit, with Modular type Switch: Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, 2 way modular type switch, modular plate, suitable size of GI box etc as required.

Power Plug wiring in PVC Conduit (2X4 Sq.mm) :- Wiring for light/power plug with 2x4 Sq.mm FR PVC insulated copper conductor songle core cable in surface/recessed PVC conduit along with 1 No. 4 Sq.mm FR PVC insulated copper conductor single core cable for loop earthing etc. as required.

Telephone Wiring in Existing Conduit:- Supplying and drawing, following pair, 0.5 sq.mm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface / recessed steel / PVC conduit as required.

Circuit/Sub-main wiring in PVC Conduit:- Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.

2x1.5 Sqmm + 1x1.5 sqmm earth wire (for Single Separate 5A from nearest switch board, Single UPS Sockets Circuits, Wall fan sockets & Control witing of indoor units VRV System)

2x2.5 Sqmm + 1x2.5 sqmm earth wire (for switch board circuit to LDB and 10 A Circuits for UPS Sockets & Seminar Hall 6 A combined Circuits).

2x4.0 Sq.mm + 1x4.0 Sq.mm earth wire.

2x6 Sqmm + 1x6 sqmm earth wire

4x6 Sqmm +2x6 sqmm earth wire.(to be used for all LDB)

4x10 Sqmm +2x10 sqmm earth wire.(to be used for all PDB)

Supply and drawing of co-axial TV Cable RG-6 grade, 0.7 mm. Solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface / recessed conduit PVC as required.

S/F PVC Conduit: Supplying and fixing of following sizes of Rigid 2 mm thick PVC conduit alongwith the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required for TV and TEL out lets.

S/F Modular type Switch / Socket:- Supplying and fixing following modular type switch / socket on the existing modular plate and switch box including connections but excluding modular plate etc as required. (to be used in switch board with sockets)

5/6 amps, one way modular switch

15/16 amps, one way modular Switch .

5/6 amps, 3 pin modular socket

6/16 amps, 6 pin modular socket

Telephone Socket Out let

TV Antenna Socket Outlet

S/F Modular type electronic fan regulator:- Supplying and fixing stepped (two module) type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required.

S/F Modular blanking plate:- Supplying and fixing of the existing modular plate and switch box excluding modular plate etc, as required.

S/F Modular boxes, base and cover plate:- Supplying and fixing following size /modules G.I. box along with modular base and cover plate for modular switches in recess etc. as required

1 or 2 modules (78mmx78mmx45mm)

4 /5 modules (78mmx140mmx50mm)

6 modules (78Xmm X 205mmx50mm)

8/9 modules (78mm X 230mmx60mm)

S/F light plug point with modular type accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 5 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc as required.

S/F power plug point with modular type accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc as required.

S/F Ceiling Rose:- Supplying and fixing 2 pin ceiling rose on the existing junction box/ wooden block including connection etc as required.

S/F Batten / Angle Holder:- Supplying and fixing batten / angle holder including connection etc as required.

Erection on incandececent light fitting :- Erection of wall bracket/ceiling fittings of all sizes and shapes containing upto two GLS amps per fitting, complete with all accessories including connection etc as required.

S/F Electonic Musical Call Bell:- Supplying and fixing electronic musical call bell suitable for D.C./A.C. single phase, 230Volts, complete etc as required.

S/F Twin twisted cable in conduit:- Providing and fixing plain 16/0.20 mm (0.50 Sq. mm) twin twisted, flxible, FR PVC insulated copper cable, in polythene sleeve of suitable size on the floor/ wall, or side of the table door etc. as requirerd.

ITC fluorescent fitting directly on surace:- Installation, testing and commissioning of Pre-wired fluorescent fitting /compact fluorescent fitting of all types, complete with all accessories and tube etc.directly on surace or ceiling/ wall, including connection with 1.5 Sq. mm. FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

ITC fluorescent fitting with down rods:- Installation, testing and commissioning of Pre-wired fluorescent fitting /compact fluorescent fitting /2x20W LED Tube light of all types, complete with all accessories and tube etc.directly on surace or ceiling/ wall, including connection with 1.5 Sq. mm. FR PVC insulated, copper conductor, single core cable and earthing including supplying and fixing ball & socket arrangement, 2 No. down roads of 20 mm dia x 1.6 mm thick steel conduit (up to 30 cm lenght), painting & wiring the down rods with 1.5 sq.mm. PVC Cu. conductor sinlge core cable and earthing etc. as required.

S/F Extra Down Rod:- Providing and fixing extra conduit down rod of 20 mm dia, 2x10 cm, length with 2x1.5 Sq.mm FR PVC insulated copper conductor, single core cable including painting etc. as required. (Note more than 5 Cm. length shall be rounded to the nearest 1)

ITC Ceiling Fan :- Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (Up to 30 cm) with 1.5 sq. mm. FRPVC insulated,copper conductor,single core cable etc, as required.

ITC Exhaust Fan upto 450 mm sweep:- installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.

S/F SP MCB DB:- Supplying and fixing following way, SP&N MCB distribution board of sheet steel for 240 Volts on surface /recess complete with tinned copper bus bar, neutral busbar, earth bar, detachable gland plate, interconnections, phophatized and powder coated painted including earthing etc. as required ( But without MCB/RCCB/ ISOLATOR). Make- Siemens/L&T/ Legrand/ Schneider.

8Way Double Door.

12Way Double Door.

16Way Double Door.

S/F TP MCB DB: Supplying and fixing following way,three pole and neutral sheet MCB distribution board, 415 volts on surface/recess complete with tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections,phosphatised and powder painted including earthing etc. as required ( But without MCB/RCCB/ ISOLATOR) Make- L&T/Legrand/ Schneider/Siemens.

4 ways (4+12) Double Door. (horizontal type)

6 ways (4+18) Double Door. (horizontal type)

8 ways (4+24) Double Door.(horizontal type)

S/F 'C' series MCB:- Supplying and fixing 240/415 V, 10 kA, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required. Make- L&T/Legrand/ Schneider/Siemens.

6/32A Single Pole

6-32 A DP MCB

6-32A TPN MCB (To use as incomer for all LDB)

50/63A TPN (To use as incommer for all TPN D.B.)

S/F SPN (DP) RCCB:- Supplying and fixing following rating,double pole (Single phase and neutral) 240 Volts, resudual current breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB-DB complete with connections, testing and commissioning etc. as required.(To be used as sub incomer in UPS DB only). (All DP RCCB shall be as per IEC:61008-1) Make:- Legrand/ Schneider/ /Siemens/L&T.

16/25A/DP RCCB 300mA.

63A/DP RCCB 300mA.

MCB BLANKING PLATE:- Supplying and fixing single pole blocking plate in the existing MCB DB complete etc. as required. Make- L&T/Legrand/ Schneider/Siemens.

P/F MV Danger Notice Plate:- Providing and fixing M.V. danger notice plate of 200mmX150mm, made of mild steel at least 2mm thick, and vitreous enamelled white on both sides, and with inscription in the single red colour on front side as required.

G.I. Pipe electrode with Sall/Charcoal:- Earthing with G.I. Earth pipe of 4.5 meter lomg, 40 mm dia including accessories, and providing massonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/cock and salt as required.

Total Earth Pits

Copper earth plate electrode:- Earthing with copper earth plate 600mm x 600mm x 3mm thick including accessorise and providing masonary encloser with cover plate hacving locking arrangment and watring pipe etc as required. ( but without chrcoal or coke and salt.) ( for UPS).

S/L 8 SWG copper wire in ground:- Supplying and laying of 8 SWG copper wire at 0.50 meter below ground level for conductor earth electrod, including soldering etc. as required.

P/F 25 x 5mm G.I. earth strip in surface/recess :- Providing and fixing 25mmx5mm G.I. earth strip in surface /recess for connections etc. as required and making the earth grid for all G.I. Earthing pits of the building.

P/F 4mm copper loop earthing wire in surface / recess:- Providing and fixing 4mm dia copper wire in surface and in recess for loop earthing as required.

P/F G.I. lighting conductor finial:- Providing and fixing of lighting conductor finial, made of 25mm dia 300mm long, G.I. tube having single prong at top with 85mm dia 3mm thik G.I. base plate including hole etc. complete as required.

Reverting, Sweating and soldring lightning conductor tape:- Reverting, Sweating and soldring of copper / GI tape (with another copper / GI tape, base of the fineal or any other matelic object) as required.

P/F G.I. lightning conductor tape in horzontal run:- Providing and fixing G.I. tape 20mm thick on parapet or surface of wall for lightning conductor complete as required.

P/F G.I. lightning conductor tape in Vertical run:- Providing and fixing G.I. tape 20mm thick on parapet or surface of wall for lightning conductor complete as required.

G.I. Pipe electrode with Sall/Charcoal:- Earthing with G.I. Earth pipe of 4.5 meter lomg, 40 mm dia including accessories, and providing massonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/cock and salt as required.

P/F 25 x 5mm G.I. earth strip in surface/recess :- Providing and fixing 25mmx5mm G.I. earth strip in surface /recess for connections etc. as required and making the earth grid for all G.I. Earthing pits of the building.

Errection of Steel Pole up to 10Mtr. in C.C & STRUT .:-

Errection of Steel Pole of length exceeding 8 meters but not exceeding 10 meters in cement concrete 1:3:6 (1 Cement, 3 coarse Sand, 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required. (Errection shall be done as per drawing attached)

Providing and fixing of PVC/XLPE indulated PVC sheathed heavy duty, aluminium armoured cable of grade 1.1KV as per IS 1554 (Part-1), etc. as required.

2 Core 6 Sq. mm XLPE Al. Ar. Cable 1.1kV.

3.5 Core 25 Sq.mm. XLPE Al. Ar. Cable 1.1kV.

3.5 Core 35 Sq.mm. XLPE Al. Ar. Cable 1.1kV.

3.5 Core 50 Sq.mm. XLPE Al. Ar. Cable 1.1kV.

3.5 Core 95 Sq.mm. XLPE Al. Ar. Cable 1.1kV.

3.5 Core 120 Sq.mm. XLPE Al. Ar. Cable 1.1kV.

3.5 Core 300 Sq.mm. XLPE Al. Ar. Cable 1.1kV.

4 Core 10 Sq. mm XLPE Al. Ar. Cable 1.1kV.

MV Cable Laying up to 25 sq. mm. in ground :- Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm. direct in ground including excavation, sand cushioning, protective covering by 2nd class bricks and refilling the trench etc as required.

MV Cable Laying up to 120 sq. mm. in ground :- Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm. but not exceeding 120 sq.mm. direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required

MV Cable Laying up to 400 sq. mm. in ground ;- Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size exceeding 120 sq.mm. but not exceeding 400 sq.mm. direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Providing of following dia GI pipe (Medium Class) in ground complete with G.I. fittings etc. as required.

Laying of Med. Class G.I.Pipe earth cutting, excavation and refilling and making the surface smooth.

Supply and fixing of 7 Meter Height Octagonal Hot Dip Galvanized pole (BOP 7030) with top dia 70mm bottom dia 130mm & made of 3 mm thickj sheet, base plate dimensions 200x200x12mm (L X B X T)including suitable sizes of foundation bolts all complete as required. (Without ARM) Cost of 7 Meter Height Octagonal Hot Dip Galvanized pole (BOP 7030)

Supply fitting, fixing of Single Arm (1 Mtr. Long) suitable for 70 mm Top. Cost of Single arm (1 Mtrs. Long) suitable for 70 mm Top.

Supply fitting, fixing of Double Arm (1 Mtr. Long)suitable for 70 mm Top Cost of Double arm (1 Mtrs. Long) suitable for 70 mm Top

Supply of 1200 mm sweep ISI marked BEE energy efficient ceiling fans complete with double ball bearing, motor, blades, downrod, canopies, capacitor, suitable for operation on 230 volts, 50 Hz., 1 phase, AC supply connection with 1.5 sq.mm PVC Copper wire complete as required (minimum BEE five star rated with minimum air delivery of 218 CFM/M and ISI marked with 2 years warranty). Colour of Ceiling Fan- White/Ivory.

Supply of 1400 mm sweep ISI marked ceiling fans complete with double ball bearing, motor, blades, downrod, canopies, capacitor, suitable for operation on 230 volts, 50 Hz., 1 phase, AC supply connection with 1.5 sq.mm PVC Copper wire complete as required (minimum BEE three star rated with minimum air delivery of 218 CFM/M and ISI marked with 2 years warranty). Colour of Ceiling Fan- White/Ivory.

Supply fiting fixing and testing fof 400 mm (16") sweep AC 230/250 volts, 50 HZ Wall Mounting Revolving Fan with brackets, cooper winding 5 star rated etc. complete all electric room etc.

Supply of 230 mm (9") Exhaust fan (Metal body) suitable for single phase 230 volts, 50 Hz., AC supply complete with motor, louvers/shutters etc. complete as required.

Supply of 300 mm (12") Exhaust fan (Metal body) suitable for single phase 230 volts, 50 Hz., AC supply complete with motor, louvers/shutters etc. complete as required.

Supply of 9W/10W LED Bulb in existing holders. ( Luminous Flux- 600lm, CCT-6500K (Cool White), CRI-80, Rated Voltage- 220V/ 240V. Beam Angle- 120 degree, Life- 25000hrs.)

Supply fitting, fixing and testing of surface/ pendent mounted with chain Batten type LED 4ft Tube light fitting with Housing & cover made up of CRCA sheet steel. Cover is fixed to the housing by means of 2 Nos. bolt with engineering plastic head along with 1 nos LED tube of 20/22W Each of luminous efficacy of efficacy >110 Lm/W. ,Lifetime of 30,000 burning hours, LM 79 and LM 80 reports need to be submitted with all accessories.

Supply, fitting, fixing & testing of 15W LED recessed Downlighter with cutout dia 145 mm suitable of Armstrong /CRG/TRAC/USG/Celotex/ POP Muduler Celling . Must be white Power doatedpreseure die cast aluminum housing for superior heat management and beautifully designed with white modled in engineering plastic

Supply, fitting, fixing & testing of Recess Mounted 36W LED 2x2 Light Fittings that enables visibility of celling material like 2'X2" False Ceiling in the centre of the light fittings with high efficiency transmission PC diffuser at the periphery of the light fixture . The housing must be powder coated extruded aluminium housing for better heat dissipation , the driver must be prewired to terminal block for seamless installation & LM 79 and LM 80 reports need to be submitted with all accessories.

Building Outer Light (45/48W LED) :-

Supply, fitting, fixing and testing of building outer lighting luminaire aerodynamically shaped single piece pressure die-cast Aluminum luminaire with high power LEDs as light source and electronic driver (IP65), along with 45/48W LED Lamp, as Energy saving as per drawing prescribed reflector and heat resistant toughened flat glass cover, with 5ft long 40mm dia G.I. pipe with 3 Nos. of iron clamps , anchor nut bolts with double washers as per direction of E/I or consultant as per drawing prescribed reflector and heat resistant toughened flat glass cover (IP-65) and in compliance to IEC Safety Standards. LM 79 and LM 80 reports to be submitted with all accessories.

LED Street Light (90/100W LED) :- Supply, fitting, fixing and testing of dtreet Light LED lighting luminaire aerodynamically shaped single piece pressure die-cast Aluminum luminaire with high power LEDs as light source and electronic driver (IP65), along with 90/100W LED Lamp, as Energy saving as per drawing prescribed reflector and heat resistant toughened flat glass cover, reflector and heat resistant toughened flat glass cover (IP-65) and in compliance to IEC Safety Standards. LM 79 and LM 80 reports to be submitted with all accessories.

250KVA, 11/0.433KV OUT DOOR TRANSFORMER (OFF LOAD TAP CHANGER) Supply, installation, testing, fixing and commissioning in correct alignment position, effecting proper connections of continuous rating of 250 KVA, 3Ph, 50Cy, 11/0.433KV, Off Circuit, (OCTC) oil cooled, copper wound, Outdoor Transformer, at full load and temp. rise not exceeding 45 degree C, by termometer in oil and 50 Degree C. by the reistance in windingafter continuous run in full load rating. The Transformer shoul oil immersed winding having Vector DY-11 HT side connected in Delta, & LT Side connected in Star with neutral brought out connected to provide separate earthing. In Transformer HT Side Bushing/ Cable End Box, & LT side - Cable End Box. Transformer shall be latest manufacturing standards as per amended IS Specifications and load and no load losses shall be limited to the values given below as per IS or Norms issued by JBVNL or which ever is lower. The transformer , . length of MS channels as per the norms of 250 KVA Outdoor Transformer with all accessories as per IS:2026, air filled cable box and accessories as per General Specifications of 250KVA out Door Transformer and should have suitable for 11KV 1 Run, 3 Core 95 Sq mm XLPE Al. Ar. Cable and LV termination box shall have suitable arrangement for 1.1 KV, 2 Run, 3.5 Core, 300 Sq. mm XLPE Al. Ar. Cable etc as required. The copper loss and Iron loss shall be as per the 3 Star rating out Door Transformer. 1 Oil Conservator with filling hole with Cap and plain oil level gauge 2. Silica gel dehydrating breather charged with silica gel 3. Oil drain valve 4. Oil filter valve 5. Lifting eyes hooks 6. Two Earthing terminals 7. Diagram and rating plate 8. Air vent 9. Explosion vent 10. 100mm dia thermo meter with thermometer pocket 11. Four bi directional plain roller. Total Cost of 250 KVA 11/0.433KV (OCTC) Outdoor Tansformer.

Supplying and fixing TPN sheet enclosure on surface or recess along with 25/32 Amp 415 Volts, , "C" curve, TP MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing TPN sheet enclosure on surface or recess along with 63 Amp 415 Volts, , "C" curve, TP MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing of modular type 25 AC Unit box with ON/OFF MCB on surface or in recess complete with connections, testing and commissioning etc. as required. (to use for Split AC)

Supplying and Instasllation of 600 mm, 230 V A.C wall mounted Air circulator, heavy duty Fan Including Fixing the bracket, making connection, testing and commissioning etc. as required.

Supplying and fixing single wall mounted 9/11 watt (2ft Long) LED type batten fitting complete with electronic diver and LED etc. directly on wall /ceiling including connections with 1.5 Sq. mm FR PVC insulatted copper conductor and earthing the body etc. as requiered. (to use as mirror light in Toilets)

Suppling and fixing of surface 15/18Watt LED (Warm Light) 100lm/w, downlighter complete with electronic diver and LED etc. directly on wall /ceiling including connections with 1.5 Sq. mm FR PVC insulatted copper conductor and earthing the body etc. as requiered. (To use in double height area)

Suppling and fixing of recess/surface 23/24Watt (1ftX1 ft) LED (Warm Light) 100lm/w, downlighter complete with electronic diver and LED etc. directly on wall /ceiling including connections with 1.5 Sq. mm FR PVC insulatted copper conductor and earthing the body etc. as requiered. (To use in double height area) .

Supplying and fixing 4' X 40 watt suspended type LED luminaire provides soft-light and glare free symmetrical illumination complete with all accessories etc. including ball and socket arrangement, 2 no. down rods of 20mm dia X 1.6 mm thick G.I. pipe upto 30 cm. length, painting and wiring the down rods and connection with 1.5 sq mm FR PVC insulated copper conductor, single core cable and earthing etc. as required.

Supplying and fixing Surface mounted 10/12 Watt LED type bulk head e comprising of pressure die casr housing with acrylic diffuser (IP65) and complete with integrated electronic driver etc. directly on wall /ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc as required.

Supplying and Fixing following watt LED Flood Light luminaire with integral control gear, lenses, heat resistant toughened clear glass cover, with black powder coated aerodynamically shaped single piece pressure die-cast Aluminum luminaire with high power LEDs as light source and electronic driver (IP65), along with 120 LED WARM LIGHT, (4000K) as Energy saving as per drawing prescribed reflector and heat resistant toughened flat glass cover including connections with FR PVC insulated copper conductor cable and earthing the body along with all fixing accessories etc. as required, with proper iron clamps, nut bolts with washers etc. to fix on minimum 65 mm dia G.I. Pipe in front of stage of Auditorioum of Museum as per direction of E/I or consultant as per drawing prescribed reflector and heat resistant toughened flat glass cover (IP-65) and in compliance to IEC Safety Standards. LM 79 and LM 80 reports to be submitted.

120 W LED Flood WARM Light (3000k)

Supplying and fixing 25/30 Watt LED type post top lantern suitable for Garden/Park/ Gate light complete with integrated electronic driver and all accessories including connection with PVC insulated copper conductor cable and earthing the body etc. as required and in compliance to IEC Safety Standards. LM 79 and LM 80 reports to be submitted .

Supply fitting and fixing of PVC/XLPE insulated PVC H.T cable for working voltage up to and including1100 Volts confirming to IS 1554 (part-1)

3 Core 95 Sq. mm 11 KV grade, armoured power H.T Cable

Supplying and drawing of UTP 4 pair CAT6 LAN (AWG 23- Blue Colour)in the existing surface /recessed steel /PVC conduit as required. (for Data Outlet in existing conduit).

1 Run of cable

Providing and fixing following rating and breaking capacity andpole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

63-100 A, 30KA, FP MCCB

Supplying and fixing following Ways surface/recess mounting, vertical type, 415 V, TPN MCCB distribution board of sheet steel, dust protected, duty powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCCBs (But without MCCBs and incomer ) as required. (Note : vertical type MCCB TPDB is normally used where 3 phase outlest are required.)

4 way (4+12) Double door

Supplying & fixing 5 amps to 32 amps rating 240/415 volts 10 kA, C curve Miniature Circuit Breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Triple Pole

Supplying and fixing of DP Sheet Steel enclosure on surface/recess along with, 25/32 A 250 V C Series DP MCB complete with connections, testing and commissioning etc. as required.

Supplyig and installing following size of perforated Hot Dipped Galvanised Iron cable trays (Galvanised thickness not less than 50 microns) with perfortion not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts and nuts, etc. as required with 2 nos. 6 nos. G.I. wire as runing earthing.

100 mm width x 50 mm depth x 1.6 mm thickness

150 mm width x 50 mm depth x 1.6 mm thickness

300 mm width x 50 mm depth x 1.6 mm thickness

Supplyig and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Bends" (Galvanised not less than 50 microns) with perfortion not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts and nuts, etc. as required.

100 mm width x 50 mm depth x 1.6 mm thickness

150 mm width x 50 mm depth x 1.6 mm thickness

300 mm width x 50 mm depth x 1.6 mm thickness

Supplyig and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (Galvanised not less than 50 microns) with perfortion not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts and nuts, etc. as required.

100 mm width x 50 mm depth x 1.6 mm thickness

150 mm width x 50 mm depth x 1.6 mm thickness

300 mm width x 50 mm depth x 1.6 mm thickness

Supplyig and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member" (Galvanised not less than 50 microns) with perfortion not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts and nuts, etc. as required.

100 mm width x 50 mm depth x 1.6 mm thickness

150 mm width x 50 mm depth x 1.6 mm thickness

300 mm width x 50 mm depth x 1.6 mm thickness

Supplyig and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Reducer" (Galvanised not less than 50 microns) with perfortion not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts and nuts, etc. as required.

100 mm width x 50 mm depth x 1.6 mm thickness

150 mm width x 50 mm depth x 1.6 mm thickness

300 mm width x 50 mm depth x 1.6 mm thickness

Technical Specifications for Cable Trays:- 1. Cable Tray shall be manufactured by steel wires, welded together and bent in to final shape. 2. All cable trays shall be manufactured with a longitudinal"T Welded"safety edge 3. The steel shall demonestrated by means of Salt Spray Tests (SST) as per the standard EN 9227. 4. Hot dipped galvanized as per the standard EN ISO 1460; at least 360 H of SST. 5 .The deflection of the cable trays must be no more than 1/200th of the distance between supports and tested in accordance with the standard I.E.C. 61537. 6. Anchor fastner size - 50X 10 mm (Make :- Hilty/ Fisher). 7. All supports, brackets( hangers), 50mm rods shall be original company make and shall be designed mechanically tested as per the standard I.E.C.61537 and the optimum span shall be 1.5 Mtrs. for above cable trays. 8. Gap between true Ceiling to cable trays shall be 450mm to 500mm.

Laying and fixing of one number PVC insulated and PVC sheated ?XLPE poer cable of 1.1 KV grade of following size on wall surface as required:-

Up to 35 sq. mm (Clamped with 1 mmthick saddle)

Above 35 sq. mm up to 95 Sq. mm (Clamped with 25 x3 mm MS Flat Clamp)

Above 95 sq. mm up to 185 Sq. mm (Clamped with 25/40 x3 mm MS Flat Clamp)

HT CABLE LAYING:- Laying of one number additional PVC insulated and PVC seathed /XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushaning, protective covering and refilling the trench etc. as required

Up to 120 Sq. mm

11 KV Cable End Termination:- Supplying and making out door cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core XLPE aluminium conductor cable of 11 KV grade as required.

1.1 KV Cable End Termination:-Supplying and making indoor cable end termination with brass double compression gland and aluminium lugs for following size of PVC insulated XLPE Al. Ar. Cable of 1.1 KV grade as required.

2 X 6 Sq. mm 1.1kV (19mm)

3.5 X 25 Sq. mm. (28mm)

3.5 X 35 Sq. mm. (32mm)

3.5 X 50 Sq. mm. (35mm)

3.5 X 95 Sq. mm.(45mm)

3.5 X 120 Sq. mm. (45mm)

3.5 X 300 Sq. mm. (70mm)

4 X 10 Sq. mm 1.1kV (19mm)

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc. as required

80 mm dia

100 mm dia

Supply, installation, testing & commissioning of 1 no. 20 KVA in parallel redundant mode with SMF back-up batteries suitable for 30 minutes configuration with :- 415V, 3 Ph input & 3 ph output ON-LINE UPS system, built-in isolation transformer, backup protection for 30 minutes and all standard accessories as required. The UPS will have in built protection for ground fault, DC reverse polarity, DC over voltage and current limitation, AC short circuit, AC over Voltage and current limitation. The UPS technology should consists of high double-conversion efficiency IGBT Based rectifier on line type UPS.

Configuration of UPS :-

3 Phase input & 3 Phase output

The above mentioned on-line UPS must have following features

1) Upgradeability :- Suitable for paralleling redundant and Should be upgradable to work as parallel redundant UPS in load sharing mode.

2) Intelligent LCD display with event logging facility.

3) Double conversion.

4) Built in paralleling kit.

5) IGBT technology for Rectifier and Inverter.

6) Split Static, Manual & Maintenance Bypass.

7) Input power factor correction less than 0.95.

8) Input harmonic distortion less than 5% at 50% load. with the application of IGBT(Insulated Gate By polar Transistor) based rectifier, but 6/12 pulse is not applicable.

9) Software communication :- RJ-45 port to communicate with BMS and Should be SNMP (Simple Network Management protocol) compatibility.

10) Phase reverse sequence operation

11) Automatic static bypass

12) Maintenance Bypass.

13) Technology : Micro processor based controls, true online, double conversion type, should have cold start facility.

14) Overall minimum Efficiency :>96%

15) Isolation ;- Built inl isolation transformer at the output of UPS System.

16) Charger :- Should have built in charger of minimum 10 Amp. (separate from rectifier)

17) IGBT bith side input and inverter side

18) SNMP Kit card.

19) Parallel Redundant Kit

20) Input phase correction kit.

21) Back-up time :- 30 min. with SMF Batteries.

VAH required :- Minimum 18000 for 20 KVA (75AH X 20 N0s.X 12V)= 18000VAH)

Cost of 1 set 20 KVA ON LINE UPS 3 Ph in coming and 3 Ph out going (With GST)

Supply, fitting, fixing, testing and installation of 6.0 KVA, Technology-IGBT-PWM withoutinbuilt isolationtransformer, Input Power single phase 160V -260V sinewave,50Hz & Single phase 230V output ON-LINE UPS system with 12V/ 26 AH Sealed Maintenance free batteries backup protection for 90 minutes and all accessories as required of reputed make UPS. With 46 Nos. 26AH,12V Battery.

Details of UPS :-

Technology : Micro processor based controls, true online, double convertion type, should have cold start facility.

Overall Efficiency :> 90%

Isolation ;- Built in isolation transformer at the output of UPS System.

Charger :- Should have built in charger of minimum 10 Amp.

Back-up time :- 90 min. with SMF Batteries.

VAH required :- Minimum 14352 for 6 KVA (26H X 46 N0s.X 12V)= 14352VAH)

Display :- Should have LCD Display with event logging facility.

Upgradeability :- Should have upgradable to work as parrallel redundent UPS in load sharing mode.

Shoftwere comunication :- Should have SNMP (Simple Network Management Protocol) compatability (optional).

Input current harmonic shall be less than 3% with the application of IGBT(Insulated Gate Bypolar Transistor) best rectifier, but 6/12 pulse is not applicable.

Sealed Maintenance free SMF Batteries for 6KVA UPS for 90 Mins. backup with open type cabinate for installation of batteries and their respective battery leads copper cables / buslinks between batteries, copper cables between UPS & batteries, with DC MCCB Box and required capacity of MCCB.

Cost of sealed maintenance free SMF Batteries with stand with 6KVA UPS.

Water Purifire

Supply , fitting fixing and commissioning of INDIAN WATER INC. PURE WATERFOR LIFE Fully automatic with autocut off RO Potable WaterPuri 2000 Plus 25 Litre RO+UV+UF Water Purifier Electrically oparated • Purification Technology RO+UV+UF• Capacity 25 Litre • Filter - Pre-filter (optional), sediment filter, activated carbon filter, anti-scalant filter, post-UF filter, • Membrane Type 80 GPD,• Power Features- • Power Requirement- 110V - 300V, 50 Hz, • Operating Voltage - 24V DC V along with all required accessories, like, connecting wires, pipes, stand and fixing euipments along with drain Pipe in put pipe and etc as required.

Cost of Water Purifire INDIAN WATER INC. PURE WATERFOR LIFE 2000 Plus 25 Litre RO+UV+UF Water Purifier Electrically oparated • Purification TechnologyRO+UV+UF• Capacity 25 Litre •

GEYZER

Supply, fitting, fixing, installation & testing of Water storage 15 Liters Geyser of BEE 5-star rating vertical type acralic rust free body, facility of temperature control ,with capillary themostat and thermal cut, ISI certified heating element along with inlet & outlet connecting pipe, fixing clamps, fasteners, etc. as required.

REFRIGERATOR

Supply, Fitting, fixing and testing of 3 Star Direct Cool Single Door Refrigerator IS:1476 latest for Direct Cool with following specifictions:-. Capacity: 80 Lit. Power Consumption: 289 Kwh/Yhr Power Requirement: 220 - 240 V, 50 Hz Insulation: Puff Eco-friendly refrigerant Compressor Type: Power saver Compressor Defrosting Type: Direct Cool Type: Single Door Built-in Stabilizer: Yes Warranty: 1 Year

82.5 KVA Silent D.G. Set :-82.5 KVA DG set of 82.5 Manual Control Panel (2 Years Warranty) Supply, fitting, fixing, installation and testing of 82.5 KVA /415 Volts, 3 Ph. Silent Diesel Generator Set (Manual Control with 2 years warranty) confirming to IS:10001/10002 AC supply complete with engine (1500 RPM) and alternator DG Set controller confiring to IS:13364 with accessories including residential type silencer and fuel service tank, battery, nattery leads, battery charger with all accessories, including MCCB of suitable rating & standard set of tools and anti-vibration mounting pads, etc. The power command controller compactable with BMS, PC & PLC compelte as required, remote mointoring and data logging with digital voltage regulator through inbuilt AVR, digital governing including protection complete as required. :- Supply of company make acoustic enclosure for 82.5 KVA CPCB approved Acoustic enclosure with 80 mm MS base plate, 2 mm CRCA sheet, 50 mm thick foam / 100 mm Rock Wool Insulation, 14 surface tank treatment, dully powder coated and painted with suitable colour with integrate Fuel Tank, services door, louvers (Fresh Air / Radiator), 1020 dia residential type Silencer, dimension as per company specification, complete with following accessories :- a) Fuel Tank. b) Batteries, battery leads and battery charger. c) Residential Silencers. d) First fill of lube oil. e) AVM Pads. In above supply item following work are also included :- i) Installation, fitting, fixing, testing and commissioning of the same. ii) Civil part for commissioning of D.G. Set iii) Installation of Exhaust system for D.G. Set shall be as per Central & State Pollution Board Norms along (C.P.C.B.) with iron structure i.e. 5 mtr. above the height of nearest building. If this will be in the scope of the contractor then charges shall be extra and that will be the actual. iv) Test run for D.G. Set without load and with load (part wise ) at least 6hrs each time.

In above supply item following work are also included :- i) Installation, fitting, fixing, testing and commissioning of the same. ii) Civil part for commissioning of D.G. Set iii) Installation of Exhaust system for D.G. Set shall be as per Central & State Pollution Board Norms along (C.P.C.B.) with iron structure i.e. 5 mtr. above the height of nearest building. If this will be in the scope of the contractor then charges shall be extra and that will be the actual. iv) Test run for D.G. Set without load and with load (part wise ) at least 6hrs each time. Supply of inbuilt Control Breaker ( thermomagnetic suitable capacity of 250A MCCB with spreader links & rotary handle) and all type of meters (Voltmeter, Ammeter, KW/m, Hz/m) and all protection indications with alarm and with suitable arrangement for 1R 120 Sq mm 3.5 Core Al. Ar. Cable etc as required. Total Cost of 82.5 KVA SILENT DG SET

6 U WALL MOUNT EQUIPMENT RACK SITC of of 6U Wall Mounted Networking Cabinet 504.65X600X500 (HXWXD): Rack must be along with the following components like; Width (mm)-600, Depth (mm) - 500, Approx.Net Wt (kg) - 10-12, CRCA 'D' Grade thickness (mm) - 1.2, RAL 9017 (Matt Black), Glass - 4mm Toughened Tinted Glass Door, Accessories:, Cooling Fan (230V A/C 90 CFM) - 2 Nos, PDU 230VAC - 1 No, Cable Manager Metal- 2 Nos, Mounting Hardware (20 sets of M6 screws,washer,cage nuts (nickel coated)) - 1 No, Wall Screws (4 sets of 2'' screws, washer,rubber grommet (nickel coated)) - 1 No, Door Lock - 1 No, Front Metal Band -1 No. In the rack there must be maintained 1 U = 1.75 inches space. Cost of Wall Mount 6 U Network Rack (GST EXCLUDED)

9 U WALL MOUNT EQAUIPMENT RACK SITC of of 9U Wall Mounted Networking Cabinet 504.65X600X500 (HXWXD): Rack must be along with the following components like; Width (mm)-600, Depth (mm) - 500, Approx.Net Wt (kg) - 20, CRCA 'D' Grade thickness (mm) - 1.2, RAL 9017 (Matt Black), Glass - 4mm Toughened Tinted Glass Door, Accessories:, Cooling Fan (230V A/C 90 CFM) - 2 Nos, PDU 230VAC - 1 No, Cable Manager Metal- 2 Nos, Mounting Hardware (20 sets of M6 screws,washer,cage nuts (nickel coated)) - 1 No, Wall Screws (4 sets of 2'' screws, washer,rubber grommet (nickel coated)) - 1 No, Door Lock - 1 No, Front Metal Band -1 No. In the rack there must be maintained 1 U = 1.75 inches space.. (1 no. for CCTV, 4 no. Smart clases, and 1 no. Audio System in Multipurpose Hall)

12 U (Wall Mount) Providing, fitting, fixing, connecting and testing of 12U LCS2 Network Wall Mount Rack: Width (mm)-600, Depth (mm) - 500, Approx.Net Wt (kg) - 27, CRCA 'D' Grade thickness (mm) - 1.2, Powder Colour for Cabinet - RAL9002, Glass - 4mm Toughened Tinted Glass Door, Accessories:, Cooling Fan (230V A/C 90 CFM) - 2 Nos, PDU 230VAC - 1 No, Cable Manager Metal - 3 Nos, Mounting Hardware (20 sets of M6 screws,washer,cage nuts (nickel coated)) - 1 No, Wall Screws (4 sets of 2'' screws, washer,rubber grommet (nickel coated)) - 1 No, Door Lock - 1 No, Front Metal Band -1 No. In the rack there must be maintained1 U = 1.75 inches space.

36 U (Floor Mounted) Providing, fixing, fitting, installation and testing of 36 U Server Cabinet (RACK) (Floor Mounted) 19" LCS2 along with all following standard accessories:-

600mm (W), 600mm (D)

Approx. Wt.120 Kg,

CRCA 'D' grade 1.6mm thick sheet, pwoder coated for cabinet RAL- 9002,

4mm Toughened Tinted Glass Door

Along with following accessories:-

1. Cooling fan 220/230V AC, of 90 CFM-------4 Nos.

2. Cable manager Metal 4 Nos.

3. PDU- 230V /AC 1 No.

4. Cable Channel 100mm wide. 2 Nos.

5. Heavy Duty Stationary Shelf 600mm(W)X475mm(D) -1 No.

6. Mounting Hardware (20 Sets of M-6 screws, washers, cage, nuts (Nickle Coated)- 3 Nos.

7. Earthing strips copper 150mm H 1 No.

8. Door Lock 1 No.

9. Caster Wheels (with breake) 2 Nos.

10. Caster Wheels (without breake) 2 Nos.

11. Front Metal Band 1 No.

Cost of 36 U server cabinet

SITC of 55" Full HD 1080p LED TV.; FIRSTOUCH Smart Television Tv 55Inch LED Backlit LCD ,Resolution (Pixels)- (3840x2160) UHD, Screen size- 55" , Smart TV, Details of accessories(included in the scope ofsupply) :-Remote Control,Connecting Cable,Batteries, Dimensions (Length xBreadth x Depth) 52” x 1.2” x 31.4. Wall Mount. Power Consumption-138 Watt. Wifi Direct, Built in Wifi. Cost of 55" Full HD LED Panel TV

Krone box:-Providing, fixing, connecting & testing of Krone box (Telephone Tag Block) in a thermoplastic, IP 65 (weather proof) enclosure, internally embedded gasket, anti corrosive, insulated and shock proof with provision for cable through IP 65 glands complete in all respects.

10 pair Tag Block (krone Box) (136 mm x 253 mm x 115 mm)

20 pair Tag Block (krone Box) (136 mm x 253 mm x 115 mm)

50 pair Tag Block (krone Box) (300 mm x 300 mm x 70 mm)

Providing, laying, connecting, testing & commissioning of multi-core telephone un-armoured cables of conductor size 0.5 sq.mm. annealed tinned electrolitic grade copper, PVC insulated, twisted pairs bunched together, over all PVC sheathed, GI strip or wire armouring laid on existing cable tray or along the wall or laid in pipes or in trenches including excavation of cable trench, sand filling covering with bricks and back filling complete as required.

10 pair PISTL10PXO. 51008

Supply and installation of Digital Telephone Set with Caller ID system with connecting cord and jacks at user end. (Provision of ID Caller telephone for reception)

IP PBX SYSTEM:- Supply, fitting, fixing, commissioning and testing of IP based 100% non-blocking IP PABX System should be a IP Compatible with rich feature set of the system and can be connected with pure Voice over IP (VoIP) communication network across corporate Local and Wide Area Networks (LAN and WAN) as & when required. Central Processing Unit: The system main software should be open architecture based. The CPU of main system shall be 32 bit processor working at 2.0 GHz or better. The system should be Wall mountable. • System Architecture should be latest pure IP and should be wall Mountable  Meet-me conference 30 party X 2 from day 1 must be available. Must Support Unified Communications Equipped with 64 Analog extensions 32 IP Extensions alongwith IP User License loaded from day expandable upto 256 IP Extensions, VOIP CARD in built charger, battery with one our back up facitity. 32 Analog Trunk Ports, 1 PRI , 02 Ports Auto Attendant- IPABX.

SITC of 2 MP Bullet Varifocal IP (IR) indoor Bullet camera (2.8-12mm Lens) (Matrix) , 3 years warranty, Day Night Type, -1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps,2.7 to 13.5 mm lens, 0.01 Lux at F1.2, 0 Lux with IR, ICR, ONVIF (PROFILE S, PROFILE G), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), Alarm: 2 inputs & 2 outputs, Audio: 1 input & 1 output, IP67, Edge Anlalytics- Line crossing detection, Intrusion detection, Scene change detection,Motion detection, Face detection, Audio exception detection, Video tampering, UL, FCC, CE certified.

SITC of Matrix 2 MP IP Mini Dome indoor Camera with 3.6 fixed lens, Audio Support, 3 years warranty, Resolution D1 (704 x 480 Pixel),HD (1280 x 720 Pixel),Full HD (1920 x 1080 Pixel) Day Night type, ( Progressive Scan CMOS, 1920 × 1080 at 25fps,2.7 to 13.5 mm Lux at F1.2, 0 Lux with IR, ICR, ONVIF (PROFILE S, PROFILE G), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), Alarm: 2 inputs & 2 outputs, Audio: 1 input & 1 output, IP67, Edge Anlalytics- Line crossing detection, Intrusion detection, Scene change detection,Motion detection, Face detection, Audio exception detection, Video tampering, UL, FCC, CE certified.

SITC of 2MP IR Bullet Fixed Camera -1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps, 2.8 mm Fixed lens, 0.01 Lux at F1.2, 0 Lux with IR, ICR, ONVIF (PROFILE S, PROFILE G), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), IP67, Edge Anlalytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Video tampering, UL, CE, FCC certified.

SITC of 32 CH NVR with 32 TB Storage (Sparsh) (SPARSH & SR-NV32F608-HE)- Connect Up to 32 IP support Cameras, 2 U Rack mounting confrigation dual-OS design, Up to 12 Megapixels Resolution, 2 HDMI output with one atleast at 4K (4096×2160) , 1 VGA output with 2MP resolution,Support H.265/MJPEG, Incoming Bandwidth 500 Mbps, 8 SATA Hard Disks, ANR Technology, 16 SATA interfaces for 8 HDDs and capacity of each HDD upto 8 TB, front panel: 1 × USB 2.0 rear panel: 2 × USB 3.0, Alarm I/O 16/4, RS-485, 4 RJ-45 10 /100/1000 Mbps self-adaptive Ethernet interface, Multiple network monitoring: Web viewer, CE, FCC, UL certified with Survelliance SD Crad ,with 8 TB storage (inclusive of 8 TB Surveillance Hard Disk:- 4 nos.)

SITC of 43" LCD 24X7 Surveillance Monitor ((SMART TV).

SITC of smart Telivision Tv 43 inches LED Backlit LCD, Resolution (Pixels) : (1920 x 1080) Full HD Typical Brightness : 300 - 399 , Wattage of Speakers : 10W x 2, 3 star rating, Power Consumption, 100- Watts, Without Sub Woofers Wall/Table mount, Number of HDMI Ports- 3, Number of USB Ports- 2, Number of VGA Ports- 1, Number of Ethernet Ports- 1, Built-in Wi- fi, without Built-in set-top Box .

Accessories for MATV NETWORK SYSTEM Supply, erection, testing and commissioning of splitter / tap off mounted in suitable sizes MS boxes for MATV system and shall be suitable for interactive system.

Two Way (S-2)

Four Way (S-4)

Two way tap off (T2)

Four way tap off (T4)

Passive Component :- (DATA) Supply fitting, fixing, and testing of BLUE/YELLOW color CAT6 LCS2 U/UTP 1 MTR (3.5 ft) factory made LCS2 Patch cord with boot Factory Crimped PVC,Performance at 250MHz Should be as per Standards - IEC 61935-2 - Ed. 3.0 ISO/IEC 11801, Usage Temp – 20 to + 60°C, No of Twists 500, No of insertions 750, 24 AWG for rack end.

Providing, drawing, connecting and testing of 6 Core unarmoured unitube Multi Mode OM3 OFC (Fiber Optics cable) from wall mounted rack to server room Rack,i,e Rack to Rack Connectivity) in existing heavy duty 25 mm PVC Pipe.

Supply fitting, fixing, and testing of BLUE/YELLOW CAT 6 LCS2 U/UTP 3 MTR (10 ft) factory made LCS2 Patch cord with boot Factory Crimped PVC,Performance at 250MHz Should be as per Standards - IEC 61935-2 - Ed. 3.0 ISO/IEC 11801, Usage Temp – 20 to + 60°C, No of Twists 500, No of insertions 750, 24 AWG at end user side.

Providing, fixing, connecting and testing of Modular of 6 port unloaded LIU SC type.

Providing, fixing, fitting, connecting and testing of white RJ 45 Cat 6 Data outlet / Toolless information outlets with white coloured RJ-45 transparent shuttered modular scoket outlets with front plate. ETL verified to meet or exceed TIA / EIA category 6 requirements, universal wiring label permitting to either T568A or T568B, UL listed, for computer networking complete in all respect suitable to fix in modular plate type switch system with connections as required.

Supplying, fitting, fixing, connecting and testing CAT6 UTP RJ45 Loaded patch panel & connector - 24 port loaded 19" panel - 1 U, Panel: DC01 galvanised sheet steel, Compliant with standards: ISO/IEC 11801 Edition 3.0 CENELEC EN 50173-1 2007 ANSI/EIA/TIA 568 C2-1 IEC series 60603-7, NFC 20730, Standard 8877 – 603.7, Contacts: gold/nickel, thickness of gold > 0.8 μm minimum, Equipped with rear cable guide to hold cable during maintenance,The connectors are connected from the front without a special tool. Equipped with 4 cassettes of 6 RJ45 Cat. 6 connectors with toolless fast connection, marked 568 A/B, Max. number of connections and disconnections: 5 without replacing the wire, Endurance: 2500 operations (plug-in/pull-out) IK03, Operating temperature: -40°C to +70°C

Providing, fixing, connecting & testing of Blanking plate (6XRJ45 Blanking plate for 19" panel - Black). .

Providing, fixing, fitting, connecting and testing of SC- Pigtial 1 Mtr 10 GB -9/125, MM

Providing, fixing, connecting and testing of of 3 Duplex SM 9/125 SC adapter plate.

Providing, fixing, fitting, connecting and testing of OS1/OS2 SC/LC duplex patch cords 3 mtr, PC

Providing, fixing, connecting & testing of Splice Tray - 12 Fiber Capacity.

ACTIVE COMPONENTS CCTV SITC of 8 port Unmanaged Network PoE Switch: L2, Unmanaged, 8 100M PoE port, 1 100M uplink port, 802.3af/at, PoE power budget 123W

SITC of 24 port Unmanaged Network PoE Switch: L2, Unmanaged, 24 100M PoE port, 1 100M uplink port, 802.3af/at, PoE power budget 310W

Access Point Supply, fitting, fixing, connecting and testing of Wireless Access Point with IEEE 802.11ac dual-band radio and embedded antenna with 3x3 MIMO, Centrally controlled and managed by WLAN, Multiple SSID with VLAN mapping, Dynamic RF coverage optimization, Warranty 5 year from Day 1

ACTIVE COMPONENTS:L2 PoE Access Switch Supply, fitting, fixing, connecting and testing of switch with 24 x 10/100/1000T PoE ports and 4 x 100/1000X SFP ports, Switching Capacity 56Gbps and Forwarding Rate 41.7Mpps, Switch should support PoE and PoE+ with 370W minimum power budget, operaating temperature 0°C to 50°C, Switch should support link reccovery within 50ms for Ring architecture, SDN or similar kind of technolgy should support, Warranty 5 year from Day 1 . Make:- WARRANTY 5 YEAR FROM DAY 1

The above L2 Managed Data Switch consists of the following:-

1. Power cord India, right angle.

2. Both side Cable connector.

3. 1 year free service pack.

Interface- 24 x 10/100/1000T ports and 4 x 100/1000X SFP ports

Switching Capacity/Forwarding Rate :- 56Gbps/41.7Mpps

Performance:- Up to 16K MAC addresses, 256MB DDR SDRAM

Management:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN,

Security:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN,

Routing:- IPv4 static routing and RIP.

Fail-over:- Switch capable of recovery within 50ms in a ring for application high availability

IPv6:- Device management over IPv6 networks with SNMPv6, Telnetv6, SSHv6 and Syslogv6

Diagnostic:- Optical Digital Diagnostics Monitoring,Automatic link flap detection and port shutdown,Port and VLAN mirroring (RSPAN)

Standard Protocol:- IEEE 802.1Q,IEEE 802.1w,IEEE 802.1s,IEEE 802.1p,IEEE 802.1AB,IEEE 802.1AX,IEEE 802.3ad

Operating Temparature:- 0°C to 50°C

Certification:- EN,UL and RoHS

Warranty:- 5 Years.

Cost of L2 Managed Data Switch

Fiber Module

Providing, fixing, connecting & testing of Gigabit Fiber Module-MM, Support up to 550mtr )

Router / UTM

Supply, fitting, fixing and testing of UTM/Router with LAN: 2 x 1000X SFP / 2 x 10/100/1000T RJ-45 combo, WAN: 2 x 1000X SFP / 2 x 10/100/1000T RJ-45 combo , HA: 2 x 10/100/1000T RJ-45, Should support URL Filtering, DoS and DDoS attack detection and protection, Antivirus, Malware protection, Static, Dynamic (BGP4, OSPF, RIPv1/v2), source-based routing, policy-based routing and IGMPv1/v2/v3. Warranty 5 year from Day 1 ( Cisco - ASA 5516-X with Fire Power Services / Allied Telesis - AT-AR3050S / Juniper - SRX300/ HP)

The above router consists of the following:-

Cisco 2901 AC Power Supply (PWR-2901-AC)

AC Power Cord (India, South Africa), C13, BS 546, 1.8m

Blank faceplate for HWIC slot on Cisco ISR

Cisco Config Pro Express on Router Flash

512MB DRAM for Cisco 2901-2921 ISR (Default)

256MB Compact Flash for Cisco 1900, 2900, 3900 ISR

IP Base License for Cisco 2901-2951

Cisco 2901-2921 IOS UNIVERSAL

2-Port Serial WAN Interface Card

Security License for Cisco 2901-2951

1 year free service pack

INTERFACE:- LAN: 2 x 1000X SFP / 2 x 10/100/1000T RJ-45 combo WAN: 2 x 1000X SFP / 2 x 10/100/1000T RJ-45 combo HA: 2 x 10/100/1000T RJ-45

Processor and memory:- 800MHz dual-core, 1GB (RAM), 4GB (Flash)

Firewall / UTM (Unified Threat Manager) :- Deep Packet Inspection, Bandwidth limiting control for applications, Bridging between LAN and WAN interfaces, Data leakage prevention, URL Filtering, DoS and DDoS attack detection and protection, Antivirus, Malware protection, (Intrusion Detection System), IPS (Inclusion Prevention System) antivirous, anti spywire with 3 yrs subscription. This equipment will also protect & prevent outsider or visitors who are not assined in the existing Network i,e Office Network System can not availed by any otsiders or they can not curropt the Network System. ( For Active & Passive mode)

Routing and Multicasting:- Static, Dynamic (BGP4, OSPF, RIPv1/v2), source-based routing, policy-based routing and IGMPv1/v2/v3

NAT:- Static, IPsec traversal, Dynamic NAPT.

High availability:- VRRP, VRRPv3

Management & authentication:- Web-based GUI,Industry-standard CLI, SNMPv2 & v3, RADIUS, TACACS+, internal user database, web authentication

Warranty:- 5 Years on Hardware.

Cost of Router / UTM

AUDIO SYSTEM Supply, Installation, Commisiong and Testing of Table top Boundry layer delegate digital long microphone unit with following features:- Technical specifications Frequency response:200 Hz to 12.5 kHz Headphones load impedance:> 32 ohms < 1k ohm Loudspeaker nominal output:72 dB SPL Length of microphone :480 mm (18.9 in) Operating temperature:0 ºC to +35 ºC Plug and play functionality for ensuring fast installation and reconfiguration times Immunity to mobile phone interference Functions: Possible-to-speak indication Request‑to‑speak indication Built-in loudspeaker with volume control Built‑in 3.5 mm (0.14 in) stereo headphones socket Built‑in volume control for headphones Color-coded LED indicator above microphone button for showing the following states: microphone on, request‑to‑speak, and possible‑to‑speak Cost of Deligate Digital Microphone Unit.

Supply, Installation, Commisiong and Testing of Table top Boundry layer Chairman digital long microphone unit with following features Technical specifications Frequency response:200 Hz to 12.5 kHz Headphones load impedance:> 32 ohms < 1k ohm Loudspeaker nominal output:72 dB SPL Length of microphone :480 mm (18.9 in) Operating temperature:0 ºC to +35 ºC Plug and play functionality for ensuring fast installation and reconfiguration times Immunity to mobile phone interference Functions Possible-to-speak indication Request‑to‑speak indication Built-in loudspeaker with volume control Built‑in 3.5 mm (0.14 in) stereo headphones socket Built‑in volume control for headphones Color-coded LED indicator above microphone button for showing the following states: microphone on, request‑to‑speak, and possible‑to‑speak Cost of Chirman Digital Microphone Unit.

Supply, fitting, fixing, testing and commissioning of Mixer High-Performance12-input small format analogue mixers with onboard effects, Iconic Ghost mic preamps with ultra-low noise performance , British EQ with sweepable mid-bands per channel, Effects Engine featuring award-winning Reverbs, Delays, Choruses and Modulations ,Limiters (High-ratio Compressors) on input channels,2-in/2-out USB audio playback and recording*Switchable Hi-Z inputs for guitars, basses and other instruments, Hi-Pass Filters (low-cut) and 48V Phantom Power on all mic channels, Comprehensive GB Series audio routing, Smooth premium-quality faders, Robust metal construction for tour-grade build quality and reliability, Internal universal power supply;

Supply, Installation, Commisiong and testing of Digital Central Control Unit for Digital Discussion.

Technical specifications

Built‑in MP3 recorder with internal memory and USB recording

Built‑in Digital Acoustic Feedback Suppression

Quick and easy connection upto 80 discussion devices

Native support for automatic HD camera control

Signal to noice :> 94 dBA

Frequency response for input :30 Hz to 20 kHz

Recording/ Playback (bit rate):64, 96, 128, 256 Kbit/sec

Nominal loudspeaker output:72 dB SPL

Operating temperature: 5 ºC to +45 ºC

Relative humidity: 5% to 98% non-condensing

Functions

Plug-and-play functionality

Web browser control

Open microphone control

Built-in MP3 recorder

Discussion control

Total Cost of Digital Central Control Unit.

Supply, fitting, fixing, commissioning and testing of 30 W cabinet speakerBuilt-in 100v/70v transformer, 4” +1.5” coaxial speaker unit.Power output RMS 30W @100V. Built-in crossover for hi-fi level use. Metal grille and metal baffle.

Supply, fiting, fixing, commissioning and testing of Four Channel Class-D Digital Power Amplifier of 240W, 230V;RMS with Switch power technology for power electricity saving. Make: Electro Voice/AKG/Herman/BOSCH.

Digital power Amplifire shall have following features:-

250W RMS per Channel,

Amplifier Output 100V, Supply input AC 230 - 50/60Hz,

Short Circuit, Power, Tempreature, Overload Protection

Auto Cooling Fans

THD <0.1%, Frequency Response L/H Cut OFF 20Hz-20KHz (+1/-2dB), SNR >80dB

Total Cost of 240/230V Power Amplifire

Supply,installation, testing and commissioning of handheld Wireless Mic system set with two transmitters dynamic microphone, Frequency Response 40Hz-15,000 Hz, Surge mode PLL Phase lock, Dynamic Range >90dB, THD < 0.5%, S/N ratio > 90dB, Carrier frequency range 720 - 830 MHz. (Wire Less Lapel Micro Phone with Receiver Unit along with all acessories and charger unit and suitable battery.)

Supply, fitting, fixing and tesing of USB Player/DVD Player with USB; Preffered

Wiring with of 2.5 Sq.MM Unarmoured Flexible Speaker Cable as per site with 2mm thick rigid 25 mm PVC pipe, modular boxes, plate, fitting, fixing, connecting and testing of the same etc. as required. Make- OEM-

Supply, fitting, fixing & testing of Gooseneck Podium microphone-wired.

Supply, fitting, fixing, commissioning and testing of 30 W cabinet speakerBuilt-in 100v/70v transformer, 4” +1.5” coaxial speaker unit.Power output RMS 30W @100V. Built-in crossover for hi-fi level use. Metal grille and metal baffle. (Make- Electo Voice/ Bosch/Bose/JBL/creston

Supply, fiting, fixing, commissioning and testing of Four Channel Class-D Digital Power Amplifier of 240W, 230V;RMS with Switch power technology for power electricity saving. Make: Electro Voice/AKG/Herman/BOSCH.

Digital power Amplifire shall have following features:-

250W RMS per Channel,

Amplifier Output 100V, Supply input AC 230 - 50/60Hz,

Short Circuit, Power, Tempreature, Overload Protection

Auto Cooling Fans

THD <0.1%, Frequency Response L/H Cut OFF 20Hz-20KHz (+1/-2dB), SNR >80dB

Total Cost of 240/230V Power Amplifire

Supply,installation, testing and commissioning of handheld Wireless Mic system set with two transmitters dynamic microphone, Frequency Response 40Hz-15,000 Hz, Surge mode PLL Phase lock, Dynamic Range >90dB, THD < 0.5%, S/N ratio > 90dB, Carrier frequency range 720 - 830 MHz. (Wire Less Lapel Micro Phone with Receiver Unit along with all acessories and charger unit and suitable battery.) (Make-Bosch/ Herman / Electro-Voice.)

Supply, fitting, fixing and tesing of USB Player/DVD Player with USB; Preffered Make; LG/Samsung or Equivalent

Wiring with of 2.5 Sq.MM Unarmoured Flexible Speaker Cable as per site with 2mm thick rigid 25 mm PVC pipe, modular boxes, plate, fitting, fixing, connecting and testing of the same etc. as required. Make- OEM-

Supply, fitting, fixing & testing of Gooseneck Podium microphone-wired. Make:- Electo Voice/ BOSCH/AKG/Heinrich.

Supply, Installation, Testing & Commissioning of Multi Media XGA LCD Projector 4,300 lumens WXGA high brightness compact projector Display System: 3 LCD system Size of effective display area: 0.75”(19mm) x 3 Bright Era LCD Panel Aspect ratio 16:10,Number of pixels : 3,072,000 (1280x800 x 3) pixels Throw Ratio :1.10:1 to 1.79:1,Zoom – Ratio : Approx. x 1.6,Contrast ratio (full white / full black) 20000:1 *2,Speaker: Speaker 16 W (monaural) INPUT A : RGB / Y PB PR input connector: Mini D-sub 15 pin female Audio input connector: Stereo mini jack,INPUT B: RGB input connector: Mini Dsub 15 pin female Audio input connector: Stereo mini jack,INPUT C: HDMI input connector: HDMI 19-pin, HDCP support Audio input connector: HDMI audio support,INPUT D: HDMI input connector: HDMI 19-pin, HDCP support Audio input connector: HDMI audio support,S VIDEO IN : S Video input connector: Mini DIN 4-pin,VIDEO IN: Video input connector: Phono jack OUTPUT : MONITOR output connector: Mini D-sub 15 pin female Audio input connector: Stereo mini jack,LAN : RJ-45, 10BASE-T/100BASE-TX,USB: Type-A & Type-B MICROPHONE IN: Microphone jack: Mini Jack Display resolution: Maximum display resolution: 1600 x 1200 dots, fV:60Hz Screen size : 30" to 300" (0.76 m to 7.62 m) (measured diagonally). Make: Sony/EPSON/Hitachi/or as approved by Consultant.

Supply,Installation,Testing & Commissioning of Projector Mounting Kit (Ceiling Mount Kit) - 3' x 3'. Powder Coated.

Supply, Installation, Testing & Commissioning of Electronic 8'x6' White Matt motorized Projection screen with RF Remote control, Aspect ratio - 4 : 3. The Motorized Screen - 8' x 6' with RF Remote Control, 16:9 Aspect ratio supported. Application : Versatile for Multiple Applications - Cine White, Material : Fabric (Sheer Weave), Type : White, Screen Gain : 1.1, Viewing, Angle : 160 (80° + L&R), Mildew Resistance : Yes, Hand Clean : Yes, Wall & Screen : CineTension2 Sable Frame, ezFrame, Lunette, Peregrin Twin*, Aerie Tension*

Supply fitting, fixing and testing of Network cable assembly, (10 m.X2 )

Supply, fitting, fixing and commissioning of Passive wall plate VGA+Audio and HDMI,

Supply, fitting, fixing and commissioning of 10 Mtr HDMI Cable;

Supply, laying, fixing, terminationg and testing of10 Mtr VGA Cable;

Supply fitting, fixing and testing of Cables, Connectors & Accessories. Make- OEM.

Supply, fitting, fixing of wall mount suitable capacity (4 KVA) Automatic Voltage Stabilizer, voltage range 130V to 280V of copper wound Transformer along with suitable size of connecting 3 Mtr 3 core 2.5 Sq. mm Flexible Copper cable ( indoor unit to Stabilizer)

Suppy of Electric kattle along with all accessories and following specifications:- . Capacity: 1.7/1.8 Lit. Consume:- 1800 - 2200W Suitable for Tea, Water & Soups Auto Switch Off Facility Body Type: Metal Body Stainless Type Warrenty: 2 Year

LT Panel For OFFICE BUILDING DATA CENTRE, WRD.

Supplying, designing, manufacturing, unloding, shifting to location, installation, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing of LT Panel of 14 SWG CRCA sheet (2 mm) steel IP –43 floor mounting cubical type Floor mounted LT Panel suitable for operation on 415V, 50Hz, 3 Ph. AC supply and fault level 36 KA with front operated construction including separate fabrication arrangement for fixing M.C.C.B.

The sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized with locking arrangement duly fixed on Base Channel Size – 75 mm x 75 mm x 6 mm having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs. Detail drawings and SLD shall be provided at the time of work order.

The Panel shall be interlocked with switchgear in such a way that no door can be opened when the switch is in ON position.The switch gear shall have mechanical arrangement for interlock defeat.The design of panel shall be such as to offer maximun safety and ease of maintenance.

The MCCB's shall be Ics = 100% Icu, with rotary handle, spreader links & pad locking arrangement, with trip setting as per load requirement with short circuit & over current protection. The breaking capacity specified is Ics=Icu value. All MCCB's shall be of thermo magnetic category type.

The LT panel shall be provided with a thermostatically controlled heating arrangement (200 W) to take care of high humidity conditions. A 5/15A socket service outlet (single phase) and 1 no. CFL light with holder shall be provided in one of the compartments as service outlet in the panel. Panel shall be so designed as to have minimum 10% spare feeders/space. The complete panel shall be fuse less type, for control circuits 2A MCB's to be used.

All openings shall be covered by soft rubber gasket, enclosure shall be galvanized. Panel shall have suitable cable entry from bottom and suitable arrangement for aluminum cables for all MCCB.

The panel shall have type test certificates with short circuit and IP protection (C.P.R.I. Test)

Aluminum Bus Bar for Panel :-

The panel includes 415V, 400A, 3Ph, 50kA, 50Hz Electrolytic Aluminium bus bar of grade 63401 WP as per I:S 5082. The current density of Aluminum shall not be more than 0.8 Amps/sq.mm cross sectional area of Bus Bar. Aluminiu Bus bar shall be with removable glands plates, cable glands and sending and receiving ends, including connection with outgoing feeders complete in all respects. The support for busbar shall be nonhygroscopic non inflammable epoxy cast resin insulators. The minimum clearance between live part shall be 35-40mm. The Aluminium bus bar shall be with heat shrinkable PVC Slived Red,Yellow,Blue & Black as (RYB & N ) after temperature and incloser derating maximum allowable temp.of bus bar shall be 90 degree C. Feeders up to 100A shall interconnected by Solid Al. Bus from Main bus Bar and interconnections below 100A shall be with minimum 1.5/2.5/4/6 sq.mm. FRLS copper wires.

Note:- Inspection of LT Panel shall be carried out by Engineering Incharge / Consultant (Eletcrical) at panel builder site and for that, all arragements shall be made by the suppilier on prior information to parrent department.

SLD along with the G.A. drawing of LT Panel will be submitted by the contractor to Engineering Incharge or to the Consultant for approval . The above SLD and G.A. Drawing of LT Panel must be based on approved SLD.

1 Set Of Fabrication part of Main LT Panel & busbar system, in CRCA Sheet Steel enclosure (IP-42) without any components & its busbar system, in CRCA Sheet Steel enclosure without any components. Name of Panel Builder :- JMD ELECTROTECH, KOKAR, ARNAV POERTECH, TATISILWAY, TTS Systematix Private Ltd, Tatisiway, Meditron, Meshra, Ranchi Green Galaxy-Kolkata or any approved Panel Builders of above make Switch Gears.

The panel shall have type test certificates with short circuit and IP protection (C.P.R.I. Test) certificate.

Make of MCCB - L &T D-shine. / Legrand DPX³ / Schneider-NSX / Siemens - 3VL or 3VA

Make of MCB - L&T/ Legrand/ Schneider / Siemens (C Series MCB of 10kA)

The Name Plate for each incoming & outgoing feeder must be in Anodized Aluminium Sheet.

Make of Switch Gears and other components of above Panel shall be decided by the Consultant (elec.).Eengineering incharge.

Bill of Material of Academic Building LT Panel :-

Location in Electric Panel Room

INDICATING

1Set Multifunction Meter having LED display accuracy Class 1 as per IEC 62053-21, RS-485 port, (Ethernet/ Modbus ready suitable for monitoring and control with BMS System) in built RTC, Aux Supply: 44-277Vac/dc. Parameters: Volts, Amps, PF, THD, F, W, Wh, VA, VAh, Var, Varh, Runhrs, Onhrs Interrupts, THD for V&I per phase, individual harmonics for V&I upto 15th level complying with IEC61557-12. Min/Max for eight parameters.

3 nos. CT 400/5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set. Make:-Kappa / Matrix

3 set. Phase indicating light shall be protected by 2 Amps SP MCB's for incomer.Make-L& T./ AE/ Schneider.

INCOMER:-

1 no. 400A/FP/36KA/ MCCB with microprocessor adjustable release type with S/C, O/L, with extended front rotary handle & spreader links with ON OFF TRIP indication. (in coming cable 1 R, 300 Sq. mm. 3.5 core Al Ar. Cable)

OUT GOING FEEDERS WITHOUT DG SUPPORT

8 no. 63A FP MCCB (25KA) with adjustable thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. For all 6 nos. for PDB and 2 nos. as spares

2 nos. 25A/FP/25KA/ MCCB thermomagnetic release type, and S/C , O/L protection, with Rotary Handle & Spreader links. (2 no. as spares )

4 no. 32A DP MCB C Series of 10 kA (Main LT Panel Room Outer lights)

OUT GOING FEEDERS WITH DG SUPPORT

INTERLOCKING

Provision of Mechnical interlocking between 1 No. 200A/FP/25KA MCCB as common out going of 1 Nos. of 200 A on load Change over for D.G incomer, in such a way so that the two supplies are not parallel at any time.

1 no. 200A TPN on load Change over panel mounted open execution typesuitable arrangement for terminal of Al. Cable

1 set 200A FP/25KA, MCCB with adjustable microprocessor release type with S/C, O/L protection with extended front rotary handle & spreader links with ON OFF & trip indications.

8 no. 25A FP MCCB (25KA) with adjustable thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. (6 nos. for LDB, and 2 nos. as spare)

5 no. 63A FP MCCB (25KA) with adjustable thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. (2 nos. for Lift Machine, 1 no for UPS VTPN DB, 1 no. TPN PDB for LAB Equipment (GR. FL. PDB-3) and 1no. As spare)

5 no. 32A DP MCB C Series of 10 kA (1 no. for Lift machine Room light DB, 2 nos. for building outer lights 2 nos. for future use, etc..)

Total Cost of Office Building LT Panel

LT Panel For HOSTEL BLOCK, DATA CENTRE, WRD.

Supplying, designing, manufacturing, unloding, shifting to location, installation, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing of LT Panel of 14 SWG CRCA sheet (2 mm) steel IP –43 floor mounting cubical type Floor mounted LT Panel suitable for operation on 415V, 50Hz, 3 Ph. AC supply and fault level 36 KA with front operated construction including separate fabrication arrangement for fixing M.C.C.B.

The sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized with locking arrangement duly fixed on Base Channel Size – 40 mm x 40 mm x 6 mm having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs. Detail drawings and SLD shall be provided at the time of work order.

The Panel shall be interlocked with switchgear in such a way that no door can be opened when the switch is in ON position.The switch gear shall have mechanical arrangement for interlock defeat.The design of panel shall be such as to offer maximun safety and ease of maintenance.

The MCCB's shall be Ics = 100% Icu, with rotary handle, spreader links & pad locking arrangement, with trip setting as per load requirement with short circuit & over current protection. The breaking capacity specified is Ics=Icu value. All MCCB's shall be of thermo magnetic category type.

The LT panel shall be provided with a thermostatically controlled heating arrangement (200 W) to take care of high humidity conditions. A 5/15A socket service outlet (single phase) and 1 no. CFL light with holder shall be provided in one of the compartments as service outlet in the panel. Panel shall be so designed as to have minimum 10% spare feeders/space. The complete panel shall be fuse less type, for control circuits 2A MCB's to be used.

All openings shall be covered by soft rubber gasket, enclosure shall be galvanized. Panel shall have suitable cable entry from bottom and suitable arrangement for aluminum cables for all MCCB.

The panel shall have type test certificates with short circuit and IP protection (C.P.R.I. Test)

Aluminum Bus Bar for Panel :-

The panel includes 415V, 300A, 3Ph, 50kA, 50Hz Electrolytic Aluminium bus bar of grade 63401 WP as per I:S 5082. The current density of Aluminum shall not be more than 0.8 Amps/sq.mm cross sectional area of Bus Bar. Aluminiu Bus bar shall be with removable glands plates, cable glands and sending and receiving ends, including connection with outgoing feeders complete in all respects. The support for busbar shall be nonhygroscopic non inflammable epoxy cast resin insulators. The minimum clearance between live part shall be 35-40mm. The Aluminium bus bar shall be with heat shrinkable PVC Slived Red,Yellow,Blue & Black as (RYB & N ) after temperature and incloser derating maximum allowable temp.of bus bar shall be 90 degree C. Feeders up to 100A shall interconnected by Solid Al. Bus from Main bus Bar and interconnections below 100A shall be with minimum 1.5/2.5/4/6 sq.mm. FRLS copper wires.

Note:- Inspection of LT Panel shall be carried out by Engineering Incharge / Consultant (Eletcrical) at panel builder site and for that, all arragements shall be made by the suppilier on prior information to parrent department.

SLD along with the G.A. drawing of LT Panel will be submitted by the contractor to Engineering Incharge or to the Consultant for approval . The above SLD and G.A. Drawing of LT Panel must be based on approved SLD.

1 Set Of Fabrication part of LT Panel & busbar system, in CRCA Sheet Steel enclosure (IP-42) without any components & its busbar system, in CRCA Sheet Steel enclosure without any components. Name of Panel Builder :- JMD ELECTROTECH, KOKAR, ARNAV POERTECH, TATISILWAY, TTS Systematix Private Ltd, Tatisiway, Meditron, Meshra, Ranchi Green Galaxy-Kolkata or any approved Panel Builders of above make Switch Gears.

The panel shall have type test certificates with short circuit and IP protection (C.P.R.I. Test) certificate.

Make of MCCB - L &T D-shine. / Legrand DPX³ / Schneider-NSX / Siemens - 3VL or 3VA

Make of MCB - L&T/ Legrand/ Schneider / Siemens (C Series MCB of 10kA)

The Name Plate for each incoming & outgoing feeder must be in Anodized Aluminium Sheet.

Make of Switch Gears and other components of above Panel shall be decided by the Consultant (elec.).Eengineering incharge.

Bill of Material of Academic Building LT Panel :-

Location near stair Case below Ist landing

INDICATING

1Set Multifunction Meter having LED display accuracy Class 1 as per IEC 62053-21, RS-485 port, (Ethernet/ Modbus ready suitable for monitoring and control with BMS System) in built RTC, Aux Supply: 44-277Vac/dc. Parameters: Volts, Amps, PF, THD, F, W, Wh, VA, VAh, Var, Varh, Runhrs, Onhrs Interrupts, THD for V&I per phase, individual harmonics for V&I upto 15th level complying with IEC61557-12. Min/Max for eight parameters. Make-L & T/ Schneider/ Satec/Siemnes

3 nos. CT 200/5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set. Make:-Kappa / Matrix

3 set. Phase indicating light shall be protected by 2 Amps SP MCB's for incomer.Make-L& T./ AE/ Schneider.

INCOMER:-

1 no. 250A FP MCCB (25KA) with adjustable thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links with ON OFF TRIP indication. (Cable size- 1 Run, 120 Sq. mm. 3.5 core Al Ar. Cable)

OUT GOING FEEDERS WITHOUT DG SUPPORT

6 no. 63A FP MCCB (25KA) with adjustable thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. For all 6 nos. for PDB )

1 nos. 25A/FP/25KA/ MCCB thermomagnetic release type, and S/C , O/L protection, with Rotary Handle & Spreader links. (1 no. as spare.)

4 no. 32A DP MCB C Series of 10 kA (Building Outer light)

OUT GOING FEEDERS WITH DG SUPPORT

INTERLOCKING

Provision of Mechnical interlocking between 1 No. 125A/FP/25KA MCCB as common out going of 1 Nos. of 125 A on load Change over for D.G incomer, in such a way so that the two supplies are not parallel at any time.

1 no. 125A TPN on load Change over panel mounted open execution typesuitable arrangement for terminal of Al. Cable

1 set 125A FP/25KA, MCCB with adjustable thermomagnetic release type with S/C, O/L protection with extended front rotary handle & spreader links with ON OFF & trip indications.

7 no. 25A FP MCCB (25KA) with adjustable thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. (6 nos. for LDB, and 1 nos. as spare)

2 no. 63A FP MCCB (25KA) with adjustable thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. ( 1 no for UPS DB & 1 no. as spare)

2 no. 32A DP MCB C Series of 10 kA (2 nos. for future use)

Total Cost of Hostel Block LT Panel

Main LT Panel For Campus :- Supplying, designing, manufacturing, unloding, shifting to location, installation, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing of LT Panel of 14 SWG CRCA sheet (2 mm) steel IP –43 floor mounting cubical type Floor mounted LT Panel suitable for operation on 415V, 50Hz, 3 Ph. AC supply and fault level 36 KA with front operated construction including separate fabrication arrangement for fixing M.C.C.B. The sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized with locking arrangement duly fixed on Base Channel Size – 75 mm x 75 mm x 6 mm having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs. Detail drawings and SLD shall be provided at the time of work order. The Panel shall be interlocked with switchgear in such a way that no door can be opened when the switch is in ON position.The switch gear shall have mechanical arrangement for interlock defeat.The design of panel shall be such as to offer maximun safety and ease of maintenance. The MCCB's shall be Ics = 100% Icu, with rotary handle, spreader links & pad locking arrangement, with trip setting as per load requirement with short circuit & over current protection. The breaking capacity specified is Ics=Icu value. All MCCB's shall be of thermo magnetic category type. The LT panel shall be provided with a thermostatically controlled heating arrangement (200 W) to take care of high humidity conditions. A 5/15A socket service outlet (single phase) and 1 no. CFL light with holder shall be provided in one of the compartments as service outlet in the panel. Panel shall be so designed as to have minimum 10% spare feeders/space. The complete panel shall be fuse less type, for control circuits 2A MCB's to be used. All openings shall be covered by soft rubber gasket, enclosure shall be galvanized. Panel shall have suitable cable entry from bottom and suitable arrangement for aluminum cables for all MCCB. The panel shall have type test certificates with short circuit and IP protection (C.P.R.I. Test)

Aluminum Bus Bar for Panel :- The panel includes 415V, 600A, 3Ph, 50kA, 50Hz Electrolytic Aluminium bus bar of grade 63401 WP as per I:S 5082. The current density of Aluminum shall not be more than 0.8 Amps/sq.mm cross sectional area of Bus Bar. Aluminiu Bus bar shall be with removable glands plates, cable glands and sending and receiving ends, including connection with outgoing feeders complete in all respects. The support for busbar shall be nonhygroscopic non inflammable epoxy cast resin insulators. The minimum clearance between live part shall be 35-40mm. The Aluminium bus bar shall be with heat shrinkable PVC Slived Red,Yellow,Blue & Black as (RYB & N ) after temperature and incloser derating maximum allowable temp.of bus bar shall be 90 degree C. Feeders up to 100A shall interconnected by Solid Al. Bus from Main bus Bar and interconnections below 100A shall be with minimum 1.5/2.5/4/6 sq.mm. FRLS copper wires. Note:- Inspection of LT Panel shall be carried out by Engineering Incharge / Consultant (Eletcrical) at panel builder site and for that, all arragements shall be made by the suppilier on prior information to parrent department. SLD along with the G.A. drawing of LT Panel will be submitted by the contractor to Engineering Incharge or to the Consultant for approval . The above SLD and G.A. Drawing of LT Panel must be based on approved SLD. 1 Set Of Fabrication part of Main LT Panel & busbar system, in CRCA Sheet Steel enclosure (IP-42) without any components & its busbar system, in CRCA Sheet Steel enclosure without any components. Name of Panel Builder :- JMD ELECTROTECH, KOKAR, ARNAV POERTECH, TATISILWAY, TTS Systematix Private Ltd, Tatisiway, Meditron, Meshra, Ranchi Green Galaxy-Kolkata or any approved Panel Builders of above make Switch Gears. The panel shall have type test certificates with short circuit and IP protection (C.P.R.I. Test) certificate. The Name Plate for each incoming & outgoing feeder must be in Anodized Aluminium Sheet. Make of Switch Gears and other components of above Panel shall be decided by the Consultant (elec.).Eengineering incharge.

Location in Electric Panel Room

INDICATING

1Set Multifunction Meter having LED display accuracy Class 1 as per IEC 62053-21, RS-485 port, (Ethernet/ Modbus ready suitable for monitoring and control with BMS System) in built RTC, Aux Supply: 44-277Vac/dc. Parameters: Volts, Amps, PF, THD, F, W, Wh, VA, VAh, Var, Varh, Runhrs, Onhrs Interrupts, THD for V&I per phase, individual harmonics for V&I upto 15th level complying with IEC61557-12. Min/Max for eight parameters. Make-L & T/ Schneider/ Satec/Siemnes

3 nos. CT 600/5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set. Make:-Kappa / Matrix

3 set. Phase indicating light shall be protected by 2 Amps SP MCB's for incomer.Make-L& T./ AE/ Schneider.

INCOMER:-

1 no. 630A/FP/36KA/ MCCB with microprocessor adjustable release type with S/C, O/L, with extended front rotary handle & spreader links with ON OFF TRIP indication. (in coming cable 2 R, 300 Sq. mm. 3.5 core Al Ar. Cable)

OUT GOING FEEDERS

1 no. 400A/FP/36KA/ MCCB with adjustable thermomagnetic release type with S/C, O/L, with extended front rotary handle & spreader links with ON OFF TRIP indication. For Office Building Panel. (in coming cable 1 R, 300 Sq. mm. 3.5 core Al Ar. Cable)

2 no. 250A FP MCCB (25KA) with adjustable thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links with ON OFF TRIP indication. (To LT Panel of AC indoor and out door Units and 1 no. for Hostel Block). (Cable size- 1 Run, 120 Sq. mm. 3.5 core Al Ar. Cable)

2 nos. 160A FP MCCB (25KA) with adjustable thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. For 1 no. for APFCR Panel and 1 no. as spare. (Cable size- 1 Run, 95 Sq. mm. 3.5 core Al Ar. Cable)

2 nos. 63A FP MCCB (25KA) with adjustable thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. (2 nos. as spares)

2 nos. 25A/FP/25KA/ MCCB thermomagnetic release type, and S/C , O/L protection, with Rotary Handle & Spreader links. (1 no. for pump motor, & 1 no. as spare )

4 no. 32A DP MCB C Series of 10 kA (Main LT Panel Room Outer lights and Gate lights, Guard Room, Main LT Panel ROOM- DB etc..)

External Lighting Panel in Separate chamber

INDICATING

1 no. 63A FP MCCB (25KA) with adjustable thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. As spare

3 nos. CT 100/5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set. Make:-Kappa / Matrix

3 sets Phase indicating light shall be protected by 2 Amps SP MCB's for incomer.Make-L& T./ AE/ Schneider.

OUT- GOING

3 sets 25A/FP/25KA/ MCCB adjustable thermomagnetic release type, and S/C , O/L protection, with Rotary Handle & Spreader links. (2 No . For external lighting and 1 no. as spare)

2 nos. 4 pole 25 A Power Contactor NO NC of three phase of suitable rating. Make:- L&T / Siemens/Legrand

2 nos. Single channel Digital Time Switch. Make:- Alpha Rex 3 – CAT No. (D21 Astro, 1 Channel.)- 412654

2 nos. Four pole two way Lexic changeover with centre off 440V AC 32 to 40A to be used in case of timer failure to by pass the timer. (LEGRAND CAT No. 604022)

Total Cost of Main LT Panel

A.P.F.C. Panel (Capacitor Bank) Auto Mannual Type

A.P.F.C. Panel (Capacitor Bank) Auto Mannual Type (APFC) Panel – 115 KVAR 8 Stage Capacitor Bank Details with mixed dielectric Ultra Heavy Duty Capacitors of following range and 1 Set 15 KVAR (2x7.5 KVAR) fixed Capacitor bank to take care of no load losses of Transformer :-

Supplying, designing,manufacturing, unloading, shifting to location, installation, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing of A.P.F.C. Panel (Capacitor Bank / Auto Mannual) of 14 SWG CRCA sheet (2 mm) steel IP –42 floor mounting dust and vermin proof cubical type Capacitor Bank Panel suitable for operation on 415V, 50Hz, 3 Ph. AC supply and fault level 50kA with front operated construction including separate fabrication arrangement for fixing MCCB, , M.C.B., Capacitors, Contactors etc.

The sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized with locking arrangement duly fixed on Base Channel with proper lifting arrangement size – 50 mm x 50 mm x 4 mm having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs and Capacitors having earthing arrangement.

All openings shall be covered by soft rubber gasket, enclosure shall be galvanized.

Aluminum Bus Bar for Panel :-

Bus bar shall be suitable for 200A, TPN busbar chamber of suitable length with (E91EWP) Eletrolytic Aluminum busbars. All busbars and interconnections shall be of suitable size Aluminum busbar, current density of Aluminum shall not be more than 0.8 Amps/sq.mm cross sectional area of Bus Bar with removel gland plates, cable glands, at sending and receiving ends, encluding connections with outgoing feeders complete in all respect and all interconnections shall be made with 2.5, 4 and 6 sq.mm. PVC Cu.wire. The Aluminium bus bar shall be with heat shrinkable PVC Slived Red,Yellow,Blue & Black as (RYB & N ) after temperature and incloser derating maximum allowable temp.of bus bar shall be 90 degree C

Panel Size - As per Drawing and shall be provided at the time of work order.

Panel Builder will provide shop drawing SLD & GA drawing along with BOM with CAT. No. of each and every components and switch gears of APFC Panel for approval of Consultant. Panel Builder shall visit the site before manufacturing the Panel. Inspection of the Panel shall be carried out at Panel Builder's factory by the Consultant before final delivery for that all arrangements shall be made by the panel Builder.

The Name Plate for each feeder must be in Anodized Aluminium Sheet.

The Panel Builder must be CPRI approved. Panel builder must produce test certificate for Type Tested & Short Ckt withstand capacity as per IEC-60439-II from CPRI.

1 Set Of Fabrication part of APFC LT Panel & busbar system, in CRCA Sheet Steel enclosure (IP-42) without any components & its busbar system, in CRCA Sheet Steel enclosure without any components. Name of Panel Builder :- JMD ELECTROTECH, KOKAR, ARNAV POERTECH, TATISILWAY, TTS Systematix Private Ltd, Tatisiway, Meditron, Meshra, Ranchi Green Galaxy-Kolkata or any approved Panel Builders of above make Switch Gears.

Location : LT Panel Room. Ground Floor

Make of MCCB - L&T D-Sine/ Legrand DPX³ / Schneider-NSX / Siemens - 3VL.

Make of MCB - (10kA-D-Series.) L&T U Version/ Legrand-Dx³/ Schneider-Acti / Siemens.

All MCCBs shall be as per IS/IES:60947-2. and MCBs shall be as per IS:8828-1993.

Bill of Material in A.P.F.C.R. Panel :-

2 Nos. 63A TP / MCB / 10kA (D tripping characteristic) for 25 KVAR Capacitor.

2 Nos. 40A TP / MCB / 10kA (D tripping characteristic) for 20 KVAR Capacitor.

2 Nos. 16A TP / MCB / 10kA (D tripping characteristic) for 7.5 KVAR Capacitor.

2 Nos. 10A TP / MCB / 10kA (D tripping characteristic) for 5 KVAR Capacitor.

Incomer

1 No. 160A FP MCCB (25KA) with thermomagnetic release and with S/C & O/L protection with front rotary handle and spreader links.

Indication:-

16 Nos. LED Indicators sets (220V) (R – 8/ G – 8 = 16 Nos.) self illuminated Red-Green (ON-OFF) push buttons, each backed up with Push Button (Red- Yellow) shall be provided for each capacitor unit to indicate the status of the unit. Make-L& T./ AE/ Rishabh.

3 Nos. LED indicatore (R Y-& B) of 220V. with 2A SP MCB protection. Make- Legrand / L&T / Rishabh )

3 Set CT 200/5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set. Make:-Kappa / Matrix / L&T

1 Nos. 16A – 2 pole / 2 way Rotary Switch. Make:- Reputed

8 Nos. 10A Toggle Switch SP – HT Make:- Reputed

1 Set Power factor correction Intelligent controller Relay with 8 steps and multi -functional display, APFCR with 8 steps. The relay shall be sensitive to pick up 1% of rated current and correct the P.F accordingly. Also the relay shall display the harmonic level of system. Make- L&T, Seimens.

1 Set VAF + Power Factor, 3Ph, Class 1, 5A, Meter Make- L&T / Seimens / Scheneider.

The capacitors for Auto Mannual Type (APFC) Panel – 115 KVAR 8 Stage Capacitor Bank Details with following parameters:- (BOX SERIES OF 440V)

1. MPPXL ,440V/50Hz,TP Shunt mixed dielectric heavy duty Capacitor.

2 Lower operating losses - 0.35W/KVAr).

3. Over current withstand capability - 1.8 times rated current.

4. Inrush current withstand capability - 300 times rated current.

5. Operating Life- 130000 hours.

6. Numbering of switching- 8000 operations per year.

7. Insulation Class H.

Mixed dielectric Ultra Heavy Duty Power Resin filled Capacitor Make:- Legrand/ L&T / Schneider -Meher

2 Nos. 25 KVAR (Power Capacitor) Ultra Heavy Duty.

2 Nos. 20 KVAR (Power Capacitor) Ultra Heavy Duty.

2 Nos. 7.5 KVAR (Power Capacitor) Ultra Heavy Duty.

2 Nos. 5 KVAR (Power Capacitor) Ultra Heavy Duty.

Total - 115 KVAR.

Capacitor Duty Contactors :- (NO/NC) Make:-Seimens / L&T.

2 Nos. For 25 KVAR – MOC 25 1NO & 1 NC (63A) (Suitable for 25 KVAR capacitor bank).

2 Nos. For 20 KVAR – MOC 20 1NO & 1 NC (40A) (Suitable for 20 KVAR capacitor bank).

2 Nos. For 7.5 KVAR – MOC 15 1NO & 1 NC (16A) (Suitable for 7.5 KVAR capacitor bank).

2 Nos. For 5 KVAR – MOC 15 1NO & 1 NC (10A) (Suitable for 5 KVAR capacitor bank).

1 no. 63 A/FP/MCCB/25KA as incomer and (7.5 x 2) = 2 Sets = 15 KVAR fixed Capacitor Bank with all required accessories like capacitor duty contactor (For each 7.5 KVAR –MOC 8.5 1NO & 1 NC (16A),) each capacitor shall with 16A TP / MCB / 10kA (D tripping characteristic) R & Y indicators, toggle switch etc. shall be fixed capacitor to take care of the no load losses of the transformer. (1 Set)

Total Cost of 115 KVAR APFCR Panel with 15 KVAR (7.5 x 2) as Fixed Capacitor Bank.

Feeder For Fire Fighting System :- Supply, fitting, fixing of 125A FP / 36kA MCCB (thermomagnetic release type) with rotary handle & spreader links and 125A four pole on load Change changeover along with enclosure. (Separate arrangement direct from Transformer to fire fighting pump panel)

1 no. 125A FP MCCB (36KA) adustable thermomagnetic release type with S/C & O/L protection with front Rotary handle, speader links. Make - L&T D-Sine/ Legrand DPX³ / Schneider-NSX / Siemens - 3WL.

1 no. 125A (4 Pole) on load changover without enclosure Panel mounted, open execution. Make- L&T/Havells/Socomec..

TOTAL Cost OF Feeder For Fire Fighting System

SAFETY ITEMS Supply and laying of 1000 mm x 600 mm x 12 mm thick chequered Rubber Matting of tested quality to with stand 15KV dielectric strenght as per IS:5424 complete in all respects.

Supply of 440V grade Rubber Hands Gloves. As per IS:4770.

Supply of tool kit with 1 pair 11 KV rubber hand gloves of approved make, as per IS:4770.

Supply of First Aid Box with all necessary materials and medicine as approved by Indian Red Cross / St. John's conforming to IS:2217.

Supply and fixing of Shock Treatment Chart with glass in Aluminium frame and to be fixed on wall in Hindi and English.

Supply and fixing position the approved single line diagram framed in 1000 x 800 mm size glass frame and installed in main switch room.

Fire Extinguisher:-Supplying, commissioning and fixing of Carbon dioxide (Co2) type fire extinguisher of 4.5 Kg. Capacity duly charged confirming to IS: 2828. Make:- Minimax,Real value/Firex/ Deflame.

Supplying and Fixing 3 Nos. 9 Ltr capacity G.I. buckets duly painted white inside and red oxide paint out side and written 'FIRE' with white paint and filled with dry sand and mounted on MS angle iron bracket of size 50x50x6mm thick and 1200mm long including grouting in wall/floor etc. as required confirming to IS:2546-1974.

Providing, fitting, fixing, fabricating, erecting of MS angle of section 50 mm x 50 mm x 6 mm size for PCC trench to make support for MS iron plate to be fixed on every after 300 mm in PCC trench.

Providing, fitting, fixing, fabricating, erecting of MS Plate of 12 mm thick for covering PCC cable trench on the support of iron angle each piece of MS plate shall be 600 mm (L) x 800 mm (W). (To cover the PCC trench in electrical panel room)

FLOOR/ WALL MOUNT LT PANEL FOR AC INDOOR & OUT DOOR UNITS

Supplying, designing, manufacturing, installation, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing of LT Panel of 14 SWG CRCA sheet (2 mm) steel IP –43 Floor/Wall mounting cubical type LT Panel suitable for operation on 415V, 50Hz, 3 Ph. AC supply and fault level 36 KA with front operated construction including separate fabrication arrangement for fixing M.C.C.B.

The sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized with locking arrangement duly fixed on Base Channel Size – 40 mm x 40 mm x 6 mm having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs. Detail drawings and SLD shall be provided at the time of work order.

The Panel shall be interlocked with switchgear in such a way that no door can be opened when the switch is in ON position.The switch gear shall have mechanical arrangement for interlock defeat.The design of panel shall be such as to offer maximun safety and ease of maintenance.

The MCCB's shall be Ics = 100% Icu, with rotary handle, spreader links & pad locking arrangement, with trip setting as per load requirement with short circuit & over current protection. The breaking capacity specified is Ics=Icu value. All MCCB's shall be of thermo magnetic category type.

The LT panel shall be provided with a thermostatically controlled heating arrangement (200 W) to take care of high humidity conditions. A 5/15A socket service outlet (single phase) and 1 no. CFL light with holder shall be provided in one of the compartments as service outlet in the panel. Panel shall be so designed as to have minimum 10% spare feeders/space. The complete panel shall be fuse less type, for control circuits 2A MCB's to be used.

All openings shall be covered by soft rubber gasket, enclosure shall be galvanized. Panel shall have suitable cable entry from bottom and suitable arrangement for aluminum cables for all MCCB.

The panel shall have type test certificates with short circuit and IP protection (C.P.R.I. Test)

Aluminum Bus Bar for Panel :-

The panel includes 415V, 300A, 3Ph, 50kA, 50Hz Electrolytic Aluminium bus bar of grade 63401 WP as per I:S 5082. The current density of Aluminum shall not be more than 0.8 Amps/sq.mm cross sectional area of Bus Bar. Aluminiu Bus bar shall be with removable glands plates, cable glands and sending and receiving ends, including connection with outgoing feeders complete in all respects. The support for busbar shall be nonhygroscopic non inflammable epoxy cast resin insulators. The minimum clearance between live part shall be 35-40mm. The Aluminium bus bar shall be with heat shrinkable PVC Slived Red,Yellow,Blue & Black as (RYB & N ) after temperature and incloser derating maximum allowable temp.of bus bar shall be 90 degree C. Feeders up to 100A shall interconnected by Solid Al. Bus from Main bus Bar and interconnections below 100A shall be with minimum 1.5/2.5/4/6 sq.mm. FRLS copper wires.

Note:- Inspection of LT Panel shall be carried out by Engineering Incharge / Consultant (Eletcrical) at panel builder site and for that, all arragements shall be made by the suppilier on prior information to parrent department.

SLD along with the G.A. drawing of LT Panel will be submitted by the contractor to Engineering Incharge or to the Consultant for approval . The above SLD and G.A. Drawing of LT Panel must be based on approved SLD.

1 Set Of Fabrication part of LT Panel & busbar system, in CRCA Sheet Steel enclosure (IP-42) without any components & its busbar system, in CRCA Sheet Steel enclosure without any components. Name of Panel Builder :- JMD ELECTROTECH, KOKAR, ARNAV POERTECH, TATISILWAY, TTS Systematix Private Ltd, Tatisiway, Meditron, Meshra, Ranchi Green Galaxy-Kolkata or any approved Panel Builders of above make Switch Gears.

The panel shall have type test certificates with short circuit and IP protection (C.P.R.I. Test) certificate.

Make of MCCB - L &T D-shine. / Legrand DPX³ / Schneider-NSX / Siemens - 3VL or 3VA

Make of MCB - L&T/ Legrand/ Schneider / Siemens (C Series MCB of 10kA)

The Name Plate for each incoming & outgoing feeder must be in Anodized Aluminium Sheet.

Make of Switch Gears and other components of above Panel shall be decided by the Consultant (elec.).Eengineering incharge.

Bill of Material of Academic Building LT Panel :-

Location in Electric Panel Room or as per suitable place

INDICATING

1Set Multifunction Meter having LED display accuracy Class 1 as per IEC 62053-21, RS-485 port, (Ethernet/ Modbus ready suitable for monitoring and control with BMS System) in built RTC, Aux Supply: 44-277Vac/dc. Parameters: Volts, Amps, PF, THD, F, W, Wh, VA, VAh, Var, Varh, Runhrs, Onhrs Interrupts, THD for V&I per phase, individual harmonics for V&I upto 15th level complying with IEC61557-12. Min/Max for eight parameters. Make-L & T/ Schneider/ Satec/Siemnes

3 nos. CT 300/5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set. Make:-Kappa / Matrix

3 set. Phase indicating light shall be protected by 2 Amps SP MCB's for incomer.Make-L& T./ AE/ Schneider.

INCOMER:-

1 no. 250A/FP/36KA/ MCCB with microprocessor adjustable release type with S/C, O/L, with extended front rotary handle & spreader links with ON OFF TRIP indication. (in coming cable 1 R, 120 Sq. mm. 3.5 core Al Ar. Cable)

OUT GOING FEEDERS WITHOUT DG SUPPORT

1 no. 250A FP MCCB (25KA) with adjustable thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links with ON OFF TRIP indication. (Cable size- 1 Run, 120 Sq. mm. 3.5 core Al Ar. Cable)

4 nos. 80A FP MCB (10KA) C Series. (Cable size - 4 core 25 SQ, mm, Un armoured Cu. Cable)

6 no. 25A FP MCB (10 KA) C Series (Cable size- 4x6+2x6 SQ. mm. FR PVC Cu. Wire) 2 nos. as spare

Total Cost of Components of LT Panel

Integral Bollards:- Providing, fitting, fixing and testing of Bollard light decorative luminaire light fixture of 800mm in length (IP-65) 9/10 W LED Lamp available in CCT of 3000K/4000K with integrated baseplate and driver for easy installation, Operating voltage of 220-240 V, wide beam optics and transluscent diffuser tube. The fixture should have extruded aluminium housing and heat resistant silicone rubber gasket, Operating temperature ranging from -20° C to 40°C, The fixture should have IP65 protection and IK10 impact resistance. Driver shall be high efficiency having efficiency > 85% and in compliance to IEC standards. with foundation, commissioning, testing all with all other accessories as per drawing provided at the time of work execution or as per the direction of E/I) Cost of Bollard light Fixture with 9W LED lamp Cost of Terminal Box (Size - 8" x 6" x 4") of 2 mm CRCA sheet steel powder coating with locking arrangement and rubber gasket etc. 2A SP MCB 2 Nos. stud type 4 studs 20A connector (1 No. for incomer and 2nd for outgoing cable) Total cost of Bollard light with all above accessories.

STEP LIGHT (OUT DOOR APPLICATION) SITC of Step light (warm Light) Robust design LED 4 W step-light is IP67/IK10, easy to install, maintain and comes with suitable mounting box, energy saving step light grey clour packed with features applications (3000/4000K0 . for Architectural: accent , Good protection against water and dust ingress and impact, with all accessories. (Steps of Open Air Theater- out door application)

GARDEN SPIKE LIGHT (OUT DOOR APPLICATION) Supply, installation, testing and commisning of 12W LED Garden Spike Light (COB Integrated Lighting) solution lighting family for Architectural: accent , Good protection against water and dust ingress and impact, with all accessories. (IP-67- OUT DOOR APPLICATION)

COPPER CABLE

Supply of following size of 1.1KV XLPE / PVC Insulated / PVC sheathed (Heavy Duty) Unarmoured electric cable with copper conductor as per IS 7098 (Part-1) 1988 with upto date Amendments. Make:- Havells. Polycab. KEI, Gloster.

Supply of 4 Core 25 Sq. mm. XLPE PVC CU. / Unarmoured Cable 1.1Ar. Cable

FIRE FIGHTING WORKS

Supply, Installation, Testing and Commissioning of electric driven, horizontal type, single/multistage, end suction type, centrifugal pump of cast iron body, C.I impallers with carbon steel shaft & mechanical seal directely coupled with TEFC SQ cage foot mounted type induction motors suiitable for operation on 3 phase, 415 volts 50 Hz AC supply with IP 55 protection for enclosurewith F class insulation confirming to IS: 325 includingcommon base frame fabricated from min. 75X50 mm M.S channel, coupling with guard foundation bolts, pressure gauge, anti-vibration pads, cement concrete foundation etc. complete in all respect as required or as directed by engineer incharge.

Main fire pump 2200 LPM

Jockey pump 180 LPM

Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, having switchgears and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42 with 400 Amp aluminium bus bar as required.

Fire pumps panel

Incoming

1 No. 200 Amp, TP&N MCCB

0-400 Amp digital ammeter with one set of current transformer

0-500 volt digital voltmeter with RYB indicator lamps, HRC control fuses.

Outgoing

1 Nos of 200 Amp TP&N MCCB (1 No for EDFP )

1 Nos of (suitable for 40 HP pump) DOL starter with over load protection, current sensing type single phase preventer with all accessories and internal wiring complete as required for automatic operations (1 No for EDFP)

1 sets 0-400 Amp digital ammeter and 1 sets current transformers.

1 Nos of 63 Amp TP&N MCCB (Jockey pump)

1 No of (suitable for 12 HP pump) HP DOL starter with over load protection, current sensing type single phase preventer with all accessories and internal wiring complete as required for automatic operations

1 set of 0-63 Amp digital ammeter and 1 set current transformer.

1 Nos of 63 Amp TP&N MCCB

Supply, Installation, Testing and Commissioning of electric driven, horizontal type, single/multistage, end suction type, centrifugal pump of cast iron body, C.I impallers with carbon steel shaft & mechanical seal directely coupled with TEFC SQ cage foot mounted type induction motors suiitable for operation on 3 phase, 415 volts 50 Hz AC supply having flow rate of min 450 LPM and head of approx 40 mtrs complete in all respect as required or as directed by engineer incharge. (Terrace Pump)

Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42.

Supply and fixing of PVC sheathed following conductor 1.1 KV grade armoured Cable of following sizes including making end termination with compression gland & bimetalic lugs, and support etc.complete as required

4.0 x 50 sq.mm (aluminium) (SOR 1908)

3.5 x 35 sq mm (aluminium) (SOR 1907)

3 × 10 sq.mm.(aluminium) (SOR 1904)

2 x 1.5 sq. mm in conduits for sensors

Providing and fixing IS marked 150 mm diameter Gate Valve complete with companion flanges, bolts, nuts, rubber insetions etc.

Providing and fixing IS marked butterfly valve (PN 1.6) complete with companion flanges, bolts, nuts, rubber insetions etc.

80 mm diameter

100 mm diameter

150 mm diameter

Providing and fixing check valve (NRV) complete with companion flanges, bolts, nuts, rubber insetions etc.

80 mm diameter

100 mm diameter

150 mm diameter

Pressure Gauge Assemble with Gate/Ball Valve

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Air release Valve

Drain Valve

MS Structure support for piping

Providing, laying, testing & commissioning of IS 1239 marked black M.S pipe including all fittings i.e bend, elbows, tees, flanges, reducing socket, nuts and bolts, gaskets etc fixed with welded / screwed joints. including necessary excavation, backfilling, removal of surplus soil etc. min. 1 mtr deep excavation and wrapping with anticorrosive treatement with 4 mm thick asphalt tape as per IS:10221, refilling the trench etc. OR fixed with screwed or welded joints, hanged with clamps, hanger supports, dash fasteners, bolts, nuts, rubber insertions etc including threading, cutting, welding, edge preparation, painting of approved colour over two coat of primer, cutting & making good the wall/ floor wherever required, complete as required or as directed by engineer incharge. .:

150 mm diameter

100 mm diameter

80 mm diameter

25 mm diameter

Providing and fixing S.S Fire Hydrant Valve of approved quality with 63 mm female, instant, ovlique, single outlet, 80 mm flanged inlet, brass spindle, cast iron wheel m A.B.S. blank cap and chain. conforming to IS: 5290 complete with companion flange, bolts, nuts, rubber insertion / compressed asbestos gasket etc. and painted in fire red colour.

Providing and fixing swinging, wall mounting type First Aid Hose Reel of approved quality and made from compresed steel sheet with dust cover, cast iron brackets including 30 m long, 19 mm nominal bore, high presure braided rubber hose as per IS:444 Type hose guide, PVC shut off nozzle with 6 mm outlet and 25 mm nominal bore gun metal inlet valve, bolts, nuts rubber insetion etc. painted in Fire red colour including cutting and making good the walls wherver required.

Providing and fixing 25 mm nominal gun metal gate valve class I with CI wheel of approved quality with union (Screwed end)

Providing and fixing in position 63 mm nominal bore and 15 m long synthetic fibre, CP fire hose pipe of approved . bearing IS: 636 -1988 type A mark and having TAC and MMD approved with a pair of 63 x 63 mm gun metal instantaneous type, heavy duty delivery hose coupling (conforming to IS: 903) bound and riveted to the hose pipe with copper rivets and copper wire complete.

Providing and fixing in position short SS brach pipe of approved quality with 63 mm male instatneous type inlet and 15 mm outlet nozzle complete conforming to IS : 903

Supplying and fixing of hose cabinet of size 450mm x 450mm x 250mm made of 2mm thick M.S. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect.

Supplying, fixing, testing & commissioning of 1 set of 63mm two way instantaneous fire brigade connection (FBC) with inbuilt NRV comprising of SS and four SS instantaneous male inlet coupling confirming to IS:604 with plug and cap with chain as required with nut & bolts, washers, high pressure gasket as required.

Providing , fixing Dry Chemical Powder (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 20oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (4 Kg Capacity)

Carbon Di-oxide Type , Gas Confirming to IS ‘15222’ , Cylinder Confirming to ‘IS 7285’ & PESO approved ,Controllable Discharge Mechanism, Discharge Hose & Horn As per ‘IS 15683’ & ‘IS 2878’ ISI mark Fire Extinguishers (Wheel Type or Squeeze Grip Type). Operating Temperature :- (-)20oC to (+)55oC Suitable for ‘B’ ‘C’ Class of FIRE (3 Kg Capacity)

Providing , fixing Modular type Fire Extinguishers for electrical rooms (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 10oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (5 Kg Capacity)

Supplying, installation, testing and commissioning of optical type Smoke detector and mounting base with LED light complete as required. .:

Supplying, installation, testing and commissioning of duel tone electronic hooter / Flasher / Strobe suitable for wall mounted complete as required. .:

Supplying, installation, testing and commissioning of manual call box in suitable enclosure with arrangement to raise the alarm when the glass is manually broken complete as required. .:

Supplying, installation, testing and commissioning of microprocess base main fire alarm control panel with LCD Display lights. The panels shall have 240 volts AC power supply automatic Battery charger 24 Volts sealed lead acid maintenance free battries as complete with batteries, battery charger illuminated numeric digram complete as required. .

Supplying, installation, testing and commissioning of microprocess base main fire alarm control panel with LCD Display lights. The panels shall have 240 volts AC power supply automatic Battery charger 24 Volts sealed lead acid maintenance free battries as complete with batteries, battery charger illuminated numeric digram complete as required. .:

Providing and laying 19mm dia PVC conduit complete with required junction boxes in recessed / surface system PVC insulated copper conductor cable of 2x1.5 sq.mm. in existing conduit as required. .:

ELEVATOR

LIFT WORK

LIFT - (MACHINE ROOM LESS )

Supplying, Installation, Testing and Commissioning of 6 Passenger – (408 Kg) Lift (gearless) having contract speed of 1.25 MPS and serving (G+2)= 3 stops in the lift shaft as per detailed specifications as under :-

Speed --> 1.25 MPS

Available shaft size:-Lift 1:-1650(w)x1500(d)

Lift Car size :- Lift 1 :- 1000(w) x 1100(d)

Floors --> G+2

Travel --> 8 Mtrs Approx.

Stops & door opening - --> 3/700 mm Wide X 2000mm High

Controller: A.C. variable voltage & variable frequency drive.

Automatic rescue device complete with dry maintenance free batteries as required.

Power-415 V, 3 phase, 50 Hz, 4 wires system

Type of doors

(i) Car Power operated, Two Speed Stainless Steel HAIRLINE thick finish.

(ii) Landing doors : Stainless Steel HAIRLINE thick finish.

Hand rail not less than 600mm long at 900mm above floor level to be fixed on all the one sides adjacent to control panel in the lift car.

The Lift shall be provided with Brail System.

Ceiling as per manufacturer's standards with Fan & LED Lights.

On each Landing outside the lift, a steel plate with illumination sign shall be provided with written on it:- DO NOT USE LIFT IN CASE OF FIRE. Fire man switch at ground floor to be provided. Interlocking provision with Fire detection system shall be provided.

Voice announcement system in the car to announce the position of the elevator in the hoistway as the car passes or stops at a floor served by the elevator.

BMS interface for lift position & 3 way Intercom system.

Car & Cwt cast iron

LIFT WORK

LIFT - (MACHINE ROOM LESS )

Supplying, Installation, Testing and Commissioning of 6 Passenger – (408 Kg) Lift (gearless) having contract speed of 1.25 MPS and serving (G+2)= 3 stops in the lift shaft as per detailed specifications as under :-

Speed --> 1.25 MPS

Available shaft size:-Lift 1:-1650(w)x1500(d)

Lift Car size :- Lift 1 :- 1000(w) x 1100(d)Glass Door

Floors --> G+2

Travel --> 8 Mtrs Approx.

Stops & door opening - --> 3/700 mm Wide X 2000mm High

Controller: A.C. variable voltage & variable frequency drive.

Automatic rescue device complete with dry maintenance free batteries as required.

Power-415 V, 3 phase, 50 Hz, 4 wires system

Type of doors

(i) Car Power operated, Two Speed Stainless Steel HAIRLINE thick finish.

(ii) Landing doors : Stainless Steel HAIRLINE thick finish.

Hand rail not less than 600mm long at 900mm above floor level to be fixed on all the one sides adjacent to control panel in the lift car.

The Lift shall be provided with Brail System.

Ceiling as per manufacturer's standards with Fan & LED Lights.

On each Landing outside the lift, a steel plate with illumination sign shall be provided with written on it:- DO NOT USE LIFT IN CASE OF FIRE. Fire man switch at ground floor to be provided. Interlocking provision with Fire detection system shall be provided.

Voice announcement system in the car to announce the position of the elevator in the hoistway as the car passes or stops at a floor served by the elevator.

BMS interface for lift position & 3 way Intercom system.

Car & Cwt cast iron

Supply of Aircooled VRF SYSTEM Unit filled with R 410-A Refrigerant, Aircooled Condenser having special blue fines with Brussless DC motor for ODU fan, along with inbuilt microprocessor panel, ODU must be tested in factory & charged Refrigerant must be atleast 17KG in single ODU. ODU PCBs must be sub cooled with Refrigerantion cycle.The microprocessor panel should be refrigerant cooled,Outdoor must contains minimum 100% of inverter compressor ,Outdoor must be suitable for working voltage 380~420 ± 10% Outdoor must deliver 100% capacity at 43°C ambient & working upto 56°C(considering ambient deration)

OUTDOOR UNIT

28HP WITH INVERTER SCROLL COOLING & HEATING(IVRFB-28THN)

3Star 1.5TR Hi wall Split Air Condenser

3Star 2.0TR Hi wall Split Air Condenser

VRF Indoor Units :- Cassettes Type :- Supply Of Four way Cassettes Type indoor unit having DC inverter motor having stepless speed control for Extra power savings, complent with blowe section ,evporator EEV electronic expasion valve ,built in draion pump filter etc with low noise lavel

1.5TR UNITS (MODEL- VLC-18)

2.0TR UNITS (MODEL- VLC-24)

2.8TR UNITS (MODEL- VLC-34)

4.0TR UNITS (MODEL- VLC-48)

Split Type :- Supply Of Hi Wall Split indoor unit complent with blowe section with motor driver ,evporator EEV electronic expasion valve ,Having 3stage of Airflow with multy stage filter with in build Filter cleaning alarm option. low noise lavel

1.3TR UNITS (MODEL- VHW-16A)

Ductable Type :- Supply Of Ductable indoor unit complent with blowe section with motor driver having noise levelnot more than 55DB,evporator EEV electronic expasion valve , Compartable to operate with cordless Remotes also., Body must be power coted .Having minimum 400CFM /TR

8.0TR UNITS (MODEL- DSD-96)

6.0TR UNITS (MODEL- DSD-72)

Cordless Remote (MODEL- CDCO-D171-00)

SUPPLY OF IMPORTED INDOOR "Y" TYPE REFNET JOINTS

Corded Remote with Blue LED Display can be operated with Cordless Remote

Installation & Commissioning of Inverter Driven Scroll VRF Units , with outdoor mounting, pressure testing, nitrogen flushing, PVC Drain piping 6 mm with insulation,Control Cable 2C x 0.75 sqmm for VRF unit, complete as requied.Installation, testing and commissioning of Copper refrigerant pipes duly insulated with 19mm/13mm close cell elastometric nitrite rubber insulation between each set of outdoor and indoor units (VRF). Pipe Thickness & Insulation thickness design to be recomended by VRF OEM only, and design to be submitted through OEM own software only.Loading unloding of indoor and outdoor unit

FURNITURE WORKS

Supply and Installation of . Fenix Desk for Reception of size 1500Wx600Dx1140H - 40X40 square Leg understructure, Laminated Glass Privacy Screen fixed on the Table Top.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . Zapper Mid back Chair.Fabric seat and mesh back. 'T' Fixed arm rest with PU Pads on arms.Synchro 1 with 1 positions of locking when back is erect. Nylon Base with 30% glass reinforced. 50mm Dia castors. 435 (Depth from lumber point to seat edge) X 490 (W). 470 (Height of seat to Back rest) X 470 (W).The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of Sofa-Alysia3 seater(3 Seater : 760mm (H) X 850 (W) X 2065 (L)).Frame :- Inner solid Frame structure made of high quality wood. The wood is kiln chemical treated tropical Meranti wood.Legs :- The legs are made of rubberwood having melamine matt finish.Seating Cushions :- The seat cushion is made of 7 inches multi layered foam of density 32D 23D 32D and HD with polyester polyfill outer layer of 180 gsm. The polyester polyfill keeps the upholstery wrinke free and soft. The seating cushions have 3 inches of elastic webbing of 350 gsm with diagonal weave. The thread used is nylon bonded to provide lasting stitch strength.Backrest :- The backrest has a 3 inch foam of 23D with polyester polyfill outer layer of 180 gsm. The polyester polyfill keeps the upholstery wrinke free and soft. The seating cushions have 2 inches of elastic webbing of 250 gsm with diagonal weave. The thread used is nylon bonded to provide lasting stitch strength.Outer Finish :- The outer finish has a superior quality leatherette stictched with nylon bonded thread and stained solid wooden legs.Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,BIFMA and SGS certificate for few of its products.

Centre table:-Supply and installation of UNDERSTRUCTURE ASSEMBLY: The understructure is an assembly of tubular frames made of M.S. E.R.W. round tubes of dia. 3.2 cm.x1.6mm thk held together with 19 mm square pipe. The ends of the tubular frames are fitted with rubber studs at the top and the bottom. The top studs are fitted with PVC vacuum pads for mounting and gripping the glass top. The tubular frames are powder coated. CENTRE-PIECE TOP : The centre piece top is made from 10mm thick Float glass with rounded corners of size 550 W X 550 D X 420 H. SHELF: It is a prelaminated particle board 18 mm thk. The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of Salsa Desklet Chair , Made of round MS tubes. Rear legs Dia 25.4mm with 2mm thick and L-shape Front legs of dia 25.4mm with 1.2mm thick, all together will be welded with support of welding fixture. Understructure is metal powder coated to the thickness of 60 to 80 Micron.Glides will be fitted at the leg bottom of the chair. Seat and Back made of Polypropylene material with Hot Runner Mould Technology. Back will have metal insert and Spring washer bracket for fixing with understructure frame.Seat will be fixed to understructure by using bumper stacks and screws.Seat Height from floor = 455mm, Seat Depth = 459mm, Seat Width = 445mm, Total Chair Height = 811mm, Total Chair width = 512mm & Total Chair Depth = 553mm. The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of Kingsley Premium Main table 1200Wx600Dx740H. Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with 2mm PVC edge banding with enhanced scratch resistance supported on 25mm thk. Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility. Wire routing / wire management groumets shall be provided on main or side table as specified by customer.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of Smart Visitor Fabric 4 Legged Chair with 'T' type fixed arms.The back is made up of foam upholstered Ply having High resilience foam on the back. The complete back is contoured to provide the needed lumbar support for long seating hours. The seat is made up of moulded foam, upholstered with cushion fabric having high tensile strength. Back Rest :- 790mm High and 500mm Width, Seat :- 460mm width and 470mm depth, Seat to Back rest height :- 650mm.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of welded Almirah 900WX450DX1980H.The Storages are made up of CRCA having shelves. The storage has equally divided shelves. The top of the Stoarge is made up of 2mm thick CRCA duly powder coated to aproved finish. The caracass and shelf are made up of 0.8mm CRCA Duly Powder Coated. The skirting is made up of 1.2mm CRCA duly powder coated to the approved finish. The shelf comes with a stiffner with a thickness of 15mm duly tested for 40Kg UDL. The doors are made of 0.8mm thick CRCA with stiffeners for support. The powder coating is of 60-80 microns. All CRCA material confirm to IS 513 CR2 2008.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of Slotted Angle Rack - 900Wx450Dx1850H, Slotted Angle Racks made up of MS duly powder coated to the thickness of 60-80 Micron. The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of Vibrant 60 Plus Workstation 1200 x 600 x 1200mm ht 60 mm thick 2 Tile based system with tabletop supported partitions. The data / electrical cutout provision is provided above/below the tabletop and skirting raceway all along the 60 mm partition. One metal fabric board and one marker tile is provided for each workstation (base tile of powder coated metal and all other tiles are of MDF fabric finish).Partition thickness is 60mm for stability and with the inside gap between two tile is approximately 50mm for higher wire carrying capacity.Frame Horizontals are made of 1mm thick CRCA sheets & the verticals are made of Aluminium Extrusions of 1.5mm thick.Frame Horizontals are made of 1mm thick CRCA sheets & the verticals are made of Aluminium Extrusions of 1.5mm thick.All the frames will be duly powder coated based on the choice of the Powder Coat colour , as per Customers choice, which will be inline with the Top trims & end trims.All the frames are fastened together by means of M6 NUTS & BOLTS . They can be attached to form a 2-way, 3-way or a 4-way configuration. All the Caps viz end, inline & universal & raceway caps are made out of Die-cast Aluminum. These caps also are finished in an epoxy powder coating finish in the same color.All the frames are fitted with M10 leveling bolts.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of 2B1F Prelam Pedestal Unit of Dimensions 400W x 470D x 675H is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade. All the exposed edges are sealed with 2mm thick PVC Imported edge banding on sides and bottom. The top and drawer facia are sealed with 2mm thick PVC edge. The drawer unit consists of 2 box drawer and 1 file drawer. The sides of Inside drawer box are of prelam particle board. The drawer box is fitted with roller Slide for free movement. The drawer unit is provided with central locking system, where in the three drawer are locked with one key.PVC recessed handles are provided for easy opening and closing of drawer. The drawer unit is fitted on castors (optional) for easy mobility. PVC edge banding are imported from Rehau or Dolken of Germany. The complete furniture unit is factory assembled with knock down fittings. The pedestal is fitted with additional (5th) castor to avoid topplig of pedestal in case of opening of any / all of the 3 drawers.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of CPU Trolley:- CPU trolley is made from 1mm Thick CRCA steel sheet. The width of the trolley can be varied for accommodating various widths of CPUs; The trolley is mounted on lockable castors from reputed manufacturers in India. The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of Kingsley Premium Main table 1500Wx750Dx740H with Kingsley Premium Side Table 1050Wx450Dx740H. Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with 2mm PVC edge banding with enhanced scratch resistance supported on 25mm thk. Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility. Wire routing / wire management groumets shall be provided on main or side table as specified by customer.Supply and installation of 2B1F Prelam Pedestal Unit of Dimensions 400W x 470D x 675H is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade. All the exposed edges are sealed with 2mm thick PVC Imported edge banding on sides and bottom. The top and drawer facia are sealed with 2mm thick PVC edge. The drawer unit consists of 2 box drawer and 1 file drawer. The sides of Inside drawer box are of prelam particle board. The drawer box is fitted with roller Slide for free movement. The drawer unit is provided with central locking system, where in the three drawer are locked with one key.PVC recessed handles are provided for easy opening and closing of drawer. The drawer unit is fitted on castors (optional) for easy mobility. PVC edge banding are imported from Rehau or Dolken of Germany. The complete furniture unit is factory assembled with knock down fittings. The pedestal is fitted with additional (5th) castor to avoid topplig of pedestal in case of opening of any / all of the 3 drawers.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of Alivio Mid back Mesh Chair:-The outer frame of back rest made up of injection moulded in black polypropylene and Inner frame made up of injection moulded in black ABS. Inner frame upholstered with mesh fabric then assembled with outer frame. The back has adjustable contoured lumber support for achieving comfortable seating posture. Lumber support made up of injection moulded in black Nylon. Lumber Support size 255mm (W) X 105mm (H) and can be adjusted up to 70mm up-down. Back rest sizes Mid Back.The seat is made up of 12mm thick (7 layers) hot pressed plywood and moluded seat foam upholstered with fabric. Seat Size 495 mm (W) X490mm (D). The armrests made up of black integral skin polyurethane with 40-55 Shore Hardness and reinforced with 2mm thick M.S. insert. Arm pad size 258mm (L) x 112mm (W). The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 6mm thick. HR steel.Arm rest is 1D. S1 Mechanism with two lever control for lock and seat height adjustment. Mechanism made out of MS Plate thickness is 3mm and seat is tilting angle is 0°~6°. and back tilting angle is 89°~109°. Also it has the back tension adjustment knob. Gas lift pipe diameter 50mm and has an Height adjustment stoke of 120mm. The base made up of Nylon with 5Nos twin wheel castors. The base is 650mm pitch circle dimeter. : The twin wheel castors are injection mouled in nylon and over moulded in polyurethane. Diameter of Castor 60 mm. Manufacturer should have ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of Vibrant 60 Plus Workstation 1050 x 600 x 1200mm ht 60 mm thick 2 Tile based system with tabletop supported partitions. The data / electrical cutout provision is provided above/below the tabletop and skirting raceway all along the 60 mm partition. One metal fabric board and one marker tile is provided for each workstation (base tile of powder coated metal and all other tiles are of MDF fabric finish).Partition thickness is 60mm for stability and with the inside gap between two tile is approximately 50mm for higher wire carrying capacity.Frame Horizontals are made of 1mm thick CRCA sheets & the verticals are made of Aluminium Extrusions of 1.5mm thick.Frame Horizontals are made of 1mm thick CRCA sheets & the verticals are made of Aluminium Extrusions of 1.5mm thick.All the frames will be duly powder coated based on the choice of the Powder Coat colour , as per Customers choice, which will be inline with the Top trims & end trims.All the frames are fastened together by means of M6 NUTS & BOLTS . They can be attached to form a 2-way, 3-way or a 4-way configuration. All the Caps viz end, inline & universal & raceway caps are made out of Die-cast Aluminum. These caps also are finished in an epoxy powder coating finish in the same color.All the frames are fitted with M10 leveling bolts.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of Alivio Cantilever Mesh Back Visitor Chair:- The outer frame of back rest made up of injection moulded in black polypropylene and Inner frame made up of injection moulded in black ABS. Inner frame upholstered with mesh fabric then assembled with outer frame. The back has adjustable contoured lumber support for achieving comfortable seating posture. Lumber support made up of injection moulded in black Nylon. The back rest size is 640mm (H) X 485mm (W). The seat is made up of 12mm thick (7 layers) hot pressed plywood and moluded seat foam upholstered with fabric. Seat Size 495 mm (W) X490mm (D). The chair has Fixed armrest. Manufacturer should have ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of Consulate main table of 2900W X 900D X 740H.The table top is Post-laminated for better abrasion and scratch resistance. The Table top is made of Particle Board with 1mm top laminate and 1mm bottom laminate. The overall thickness of the Table top from visible side 54mm. The complete thickness of the table top is minimum 36mm with addition of 18mm baton on the visible side. All exposed edges have 2mm PVC edge banding. The modesty is Post-laminated for better abrasion and scratch resistance. The Modesty is made of 18mm Particle Board with 1mm top laminate and 1mm bottom laminate. All exposed edges have 2mm PVC edge banding.The understructure is 200mm wide on both sides. It is made up of prelam particle board and is black in colour. All exposed edges have 2mm PVC edge banding. The understructure has wire management properties and can carry concealed wires within it.The understructure has the capability of carrying wires within it. The main table has an access flap arrangement for easy access of switches and sockets for connecting the gadgets. The access flap cover is made of Aluminum extrusion and powder coated upto 50-60 microns.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of Consulate Side Return Table-1200W X 500D X 740H. The table top is Post-laminated for better abrasion and scratch resistance. The Table top is made of 36mm Particle Board with 1mm top laminate and 1mm bottom laminate. All exposed edges have 2mm PVC edge banding. The Table top colour is matching to the main table.The modesty is Post-laminated for better abrasion and scratch resistance. The Modesty is made of 18mm Particle Board with 1mm top laminate and 1mm bottom laminate. All exposed edges have 2mm PVC edge banding.The understructure is made of 25mm thick prelam particle. The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of 3Drawer PEDESTAL(400 X 470 X 545)made up of 18mm thk. particle board conforming to IS : 12823 Interior Grade with postformed edge profile on top with premium central locking and 3 equal size drawers with roller slide mechanism for added mobility.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of Consulate Back Storage Unit of 2400MM Width [2 Unit 750 X 450 X 1950(Tower Glass Door Storage) + 1 Unit 900 X 450 X 740 Storage] made up of 18mm thk. particle board conforming to IS : 12823 Interior Grade with PVC edge profile on top.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of Define Mid Back Chair. Seat and Back :- Leatherette. Armrest :- Height adjustable 1 dimensional arm rest with PU Pads on arms. Mechanism :- Synchro 4 with 4 positions of locking Base :- Aluminium Die cast Castors :- 60mm Dia castors inclusive of 10mm PU. Seat Dimensions :- 440 (Depth from lumber point to seat edge) X 510 (W) Back Dimensions :- 735 (Height of seat to Back rest) X 560 (W) Gas Lift:Meets DIN 4550 Class 3.Meets ANSI BIFMA performance standards.Tested for 1, 00,000 Cycles Mechanism: Synchro 4 Position BIFMA Compliant Mechanism. Mechanism tested & certified as per BIFMA stds - Cyclic test with a load of 45 Kgs on the back & dead weight of 102 Kgs on the seat, tested for 3,00,000 cycles.• Back Tilt: xx degrees.• With back tension adjustment knob.• Locking Positions: 4position, can be locked & unlocked by lever.• Tested for 3, 00,000 Cycles as per ANSI BIFMA X5.1 -2002.60mm Dia castors inclusive of 10mm PU.Movements of Seat Pan & Back Support complies with BIFMA Castor.Complies to ANSI / BIFMA X 5.1 – 2002.Tested for 1, 00, 000 Cycles Fabric:- Abrasion Resistance: Tested & certified by 3Ts Lab, Govt of India, for higher abrasion resistance as per ASTM-D 4966:1998. After 100,000 cycles no damage to threads leading to long life of fabric . Flame Ability: BS EN 1021-1 1994(cigarette); BS 7176: 1995(low hazard) Fire Retardant Fabric: Class 1 Color Fasted ness: Light : 5 + (BS 1006 1990) , Rubbing: Dry Class: 5 Wet .The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of Define Chair. Seat and Back :- Leatherite. Armrest :- Height adjustable 2 dimensional arm rest with PU Pads on arms. Mechanism :- Synchro 4 with 4 positions of locking Base :- Aluminium Die cast Castors :- 60mm Dia castors inclusive of 10mm PU. Seat Dimensions :- 440 (Depth from lumber point to seat edge) X 510 (W) Back Dimensions :- 735 (Height of seat to Back rest) X 560 (W) Gas Lift:Meets DIN 4550 Class 3.Meets ANSI BIFMA performance standards.Tested for 1, 00,000 Cycles Mechanism: Synchro 4 Position BIFMA Compliant Mechanism. Mechanism tested & certified as per BIFMA stds - Cyclic test with a load of 45 Kgs on the back & dead weight of 102 Kgs on the seat, tested for 3,00,000 cycles.• Back Tilt: xx degrees.• With back tension adjustment knob.• Locking Positions: 4position, can be locked & unlocked by lever.• Tested for 3, 00,000 Cycles as per ANSI BIFMA X5.1 -2002.60mm Dia castors inclusive of 10mm PU.Movements of Seat Pan & Back Support complies with BIFMA Castor.Complies to ANSI / BIFMA X 5.1 – 2002.Tested for 1, 00, 000 Cycles Fabric:- Abrasion Resistance: Tested & certified by 3Ts Lab, Govt of India, for higher abrasion resistance as per ASTM-D 4966:1998. After 100,000 cycles no damage to threads leading to long life of fabric . Flame Ability: BS EN 1021-1 1994(cigarette); BS 7176: 1995(low hazard) Fire Retardant Fabric: Class 1 Color Fasted ness: Light : 5 + (BS 1006 1990) , Rubbing: Dry Class: 5 Wet .Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,BIFMA and SGS certificate for few of its products.

Supply and installation of Sofa-Alysia1 seater(1 Seater : 760mm (H) X 850 (W) X 895 (L)).Frame :- Inner solid Frame structure made of high quality wood. The wood is kiln chemical treated tropical Meranti wood.Legs :- The legs are made of rubberwood having melamine matt finish.Seating Cushions :- The seat cushion is made of 7 inches multi layered foam of density 32D 23D 32D and HD with polyester polyfill outer layer of 180 gsm. The polyester polyfill keeps the upholstery wrinke free and soft. The seating cushions have 3 inches of elastic webbing of 350 gsm with diagonal weave. The thread used is nylon bonded to provide lasting stitch strength.Backrest :- The backrest has a 3 inch foam of 23D with polyester polyfill outer layer of 180 gsm. The polyester polyfill keeps the upholstery wrinke free and soft. The seating cushions have 2 inches of elastic webbing of 250 gsm with diagonal weave. The thread used is nylon bonded to provide lasting stitch strength.Outer Finish :- The outer finish has a superior quality leatherette stictched with nylon bonded thread and stained solid wooden legs.Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,BIFMA and SGS certificate for few of its products.

Supply and installation of Presidency Main Table with Access Flap 1950MM x 900 MM x 740 mm with side table 1200 x 500 x 700mm and Prelam pedestal 3B Mobile Pedestal Unit of size 400W x 470D x 545H completely made up of post lam finish conforming to IS : 12823 Interior Grade with post formed finish. Top are with 25mm thk boards with post formation on 2 sides and 2mm PVC edge banding with enhanced scratch resistance supported on 25mm thk. Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility. Wire routing / wire management groumets shall be provided on main or side table as specified by customer.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of Consulate Back Storage Unit of 2400MM Width [1 Unit 750 X 450 X 1950(Tower Glass Door Storage) + 1 Unit 900 X 450 X 740 Storage] made up of 18mm thk. particle board conforming to IS : 12823 Interior Grade with PVC edge profile on top.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installation of Alivio High back Mesh Chair:-The outer frame of back rest made up of injection moulded in black polypropylene and Inner frame made up of injection moulded in black ABS. Inner frame upholstered with mesh fabric then assembled with outer frame. The back has adjustable contoured lumber support for achieving comfortable seating posture. Lumber support made up of injection moulded in black Nylon. Lumber Support size 255mm (W) X 105mm (H) and can be adjusted up to 70mm up-down. Back rest sizes High Back (HB) 850+40mm (H) X 485mm (W) with Head rest.The seat is made up of 12mm thick (7 layers) hot pressed plywood and moluded seat foam upholstered with fabric. Seat Size 495 mm (W) X490mm (D). The armrests made up of black integral skin polyurethane with 40-55 Shore Hardness and reinforced with 2mm thick M.S. insert. Arm pad size 258mm (L) x 112mm (W). The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 6mm thick. HR steel.Arm rest is 2D arms with height adjustable up to 80mm & front and back with adjustable up to 60mm.: Mechanism with four lever control for lock and seat height adjustment. Mechanism made out of MS Plate thickness is 3mm and seat is tilting angle is 0°~6°. and back tilting angle is 89°~109°. Also it has the back tension adjustment knob. Gas lift pipe diameter 50mm and has an Height adjustment stoke of 120mm. The base made up of Aluminium die cast with 5Nos twin wheel castors. The base is 650mm pitch circle dimeter. : The twin wheel castors are injection mouled in nylon and over moulded in polyurethane. Diameter of Castor 60 mm. The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . Chancellor Main table 1800Wx900Dx740H with Side Table 1200WX450DX740H. Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with 2mm PVC edge banding with enhanced scratch resistance supported on 25mm thk. Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility. Wire routing / wire management groumets shall be provided on main or side table as specified by customer.The Pedestal Unit of Dimensions 400W x 470D x 675mmH is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade. All the exposed edges are sealed with 2mm thick PVC Imported edge banding on sides and bottom. The top and drawer facia are sealed with 2mm thick PVC edge. The drawer unit consists of 2 box drawer and 1 file drawer. The sides of Inside drawer box are of prelam particle board. The drawer box is fitted with roller Slide for free movement. The drawer unit is provided with central locking system, where in the three drawer are locked with one key.PVC recessed handles are provided for easy opening and closing of drawer. The drawer unit is fitted on castors (optional) for easy mobility. PVC edge banding are imported from Rehau or Dolken of Germany. The complete furniture unit is factory assembled with knock down fittings. The pedestal is fitted with additional (5th) castor to avoid topplig of pedestal in case of opening of any / all of the 3 drawers.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . Prelam Half ht Storage 900WX425DX740H, body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 9mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding.The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. PVC edge banding are imported from Rehau or Dolken of Germany..The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . That's It High back chair : The cushioned seat assembly shall consists of moulded polyurethane foam upholstered with fabric. The foam is assembled over a 12mm thick hot pressed plywood . The back shall made up of two piece injection moulded frame. The inner frame shall be upholstered with mesh fabric and mounted on the main assembly.Lumber support made up of injection moulded in black P.P and upholstered with PU foam. Lumber support size 160 mm (W) x 90 mm (H) at fixed position Size of back shall be (W)-550mm, (H)-580mm & size of seat shall be (W)-500 mm x (D)-440mm. Armrest has option of height adjustment . The arm top is made of soft moulded PU .The mechanism of chair shall have following features:360 degree revolving type, Synchro mechanism, Tilt tension adjustment, multi position tilt limiter with Back-safety return feature. The chair shall be provided with pneumatic height adjustment which shall have stroke of 95 +/- 5 mm. The pedestal shall be made of Die Cast Aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 650 +/- 10 mm pitch-centre-dia (700 +/- 10 mm with castors). The 50 mm Dia castor of 5 nos twin wheel castors shall be injection moulded in PP . Overall dimensions of Chair shall be, Width of Chair - 700 mm, Depth of Chair - 700 mm as measured from pedestal below. Height from ground - min 1200 to max 1210 mm. Seat height - min 445 mm to max 535 mm. Dimensions tolerance / variations shall be within +/- 10 mm. Chair tested as per ANSI/BIFMA x5.1 standards.Chair has the head rest with flexible position control.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . That's It Cantilever chair. The cushioned seat assembly shall consists of moulded polyurethane foam upholstered with fabric. The foam is assembled over a 12mm thick hot pressed plywood . The back shall made up of two piece injection moulded frame. The inner frame shall be upholstered with mesh fabric and mounted on the main assembly. Lumber support made up of injection moulded in black P.P and upholstered with PU foam. Lumber support size 160mm (W) x 90mm (H) at fixed position.Size of back shall be (W)-55cm, (H)-58.0cm & size of seat shall be (W)-50 cm x (D)-44.0cm. Armrest has option of height adjustment . The arm top is made of soft moulded PU .The visitor base is cantilever type. Overall dimensions of Chair shall be, Width of Chair - 70.0cm, Depth of Chair - 70.0 cm as measured from pedestal below. Height from ground - min 102.5 cm. Seat height - min 44.5 cm. Dimensions tolerance / variations shall be within +/- 1 cm. Chair tested as per ANSI/BIFMA x5.1 standards.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . WUDSAFE-Prelam full height storage 900 mm X 425 mm X 1986 mm.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 9mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding.The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. PVC edge banding are imported from Rehau or Dolken of Germany.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . Group Think Conference table- 28 seater. Modular Conference System Available in standard modules, made of 25mm thick MDF with waterfall top edges finished in PVC Membrane using unique wrap around technology for better aesthetics & long lasting use. Understructure – Legs made of 25mm thick standard Black matt colour post formed panels interconnected with 18mm thick standard Black matt colour pre-laminated modesty panels, with height adjustable levelers to take care of uneven floors. Wire Management – Concealed wire management to take care of basic wiring requirements both horizontally & vertically. For closed configurations, liftable top cover, made of 12mm MDF finished in PVC Membrane, is provided to access the horizontal wire carrier. For open configurations, wire channel is mounted on the inner side of modesty panel for horizontal wire carrying. Vertical wire management is through flexible vertical wire manager. Standard table top height – 740mm. Designed for Flexibility through modular Construction, PVC Membrane Finish Tops for seamless surface, Post formed Legs for safe use, Provision for easy wire management, Upgradeable / reconfigurable for future needs. The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . Adapt Mid back Mesh Chair:-The seat shall made up of plywood and moulded polyurethane foam upholstered with fabric. Backrest assembly is of injection moulded plastic with black mesh fabric and height adjustable lumbar support pad. The moulded polyurethane foam for seat is with density=50-55 kg/m ³.The dimensions of seat shall be- 480 mm(W) x 450 mm(D) and of back shall be 465 mm(W) x 515 mm(H). Armrest has 1 way button operated height adjustment and depth adjustment. The arm top is made of soft moulded PU with MS insert. The mechanism of chair shall have following features:360 degree revolving type, Synchronous Mechanism.The chair shall be provided with Class 4 pneumatic height adjustment which shall have stroke of 112 mm. The pedestal shall be injection moulded in glass filled Nylon and fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 1 cm pitch-centre-dia (700 +/- 10 mm with castors). The twin wheel castors shall be injection moulded in black polypropylene. The cushioned head support is adjustable in height and angle for optimum user comfort. Overall dimensions of Chair shall be, Width of Chair - 700 mm, Depth of Chair - 700 mm as measured from pedestal below. Height from ground - min 925 to max 1030 mm. Seat height - min 410 mm to max 515 mm. Dimensions tolerance / variations shall be within +/- 1 cm. Chair tested as per ANSI/BIFMA x5.1 standards. .The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products. The outer finish has a superior quality leatherette stictched with nylon bonded thread and stained solid wooden legs.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . Vibrant 60 Plus Workstation 900 x 600 x 1200mm ht 60 mm thick 2 Tile based system with tabletop supported partitions. The data / electrical cutout provision is provided above/below the tabletop and skirting raceway all along the 60 mm partition. One metal fabric board and one marker tile is provided for each workstation (base tile of powder coated metal and all other tiles are of MDF fabric finish).Partition thickness is 60mm for stability and with the inside gap between two tile is approximately 50mm for higher wire carrying capacity.Frame Horizontals are made of 1mm thick CRCA sheets & the verticals are made of Aluminium Extrusions of 1.5mm thick.Frame Horizontals are made of 1mm thick CRCA sheets & the verticals are made of Aluminium Extrusions of 1.5mm thick.All the frames will be duly powder coated based on the choice of the Powder Coat colour , as per Customers choice, which will be inline with the Top trims & end trims.All the frames are fastened together by means of M6 NUTS & BOLTS . They can be attached to form a 2-way, 3-way or a 4-way configuration. All the Caps viz end, inline & universal & raceway caps are made out of Die-cast Aluminum. These caps also are finished in an epoxy powder coating finish in the same color.All the frames are fitted with M10 leveling bolts.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . Sofa-Alysia2 seater 730mm (H) X 835 (W) X 1526 (L)).Frame :- Inner solid Frame structure made of high quality wood. The wood is kiln chemical treated tropical Meranti wood.Legs :- The legs are made of rubberwood having melamine matt finish.Seating Cushions :- The seat cushion is made of 7 inches multi layered foam of density 32D 23D 32D and HD with polyester polyfill outer layer of 180 gsm. The polyester polyfill keeps the upholstery wrinke free and soft. The seating cushions have 3 inches of elastic webbing of 350 gsm with diagonal weave. The thread used is nylon bonded to provide lasting stitch strength.Backrest :- The backrest has a 3 inch foam of 23D with polyester polyfill outer layer of 180 gsm. The polyester polyfill keeps the upholstery wrinke free and soft. The seating cushions have 2 inches of elastic webbing of 250 gsm with diagonal weave. The thread used is nylon bonded to provide lasting stitch strength.Outer Finish :- The outer finish has a superior quality leatherette stictched with nylon bonded thread and stained solid wooden legs.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . Kingsley Supreme Main table 1800Wx900Dx740H with Kingsley Supreme Side Table 1200Wx450Dx740H. Postform particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with 2mm PVC edge banding with enhanced scratch resistance supported on 25mm thk. Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility. Wire routing / wire management groumets shall be provided on main or side table as specified by customer.Supply and Installation of . 2B1F Prelam Pedestal Unit of Dimensions 400W x 470D x 675H is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade. All the exposed edges are sealed with 2mm thick PVC Imported edge banding on sides and bottom. The top and drawer facia are sealed with 2mm thick PVC edge. The drawer unit consists of 2 box drawer and 1 file drawer. The sides of Inside drawer box are of prelam particle board. The drawer box is fitted with roller Slide for free movement. The drawer unit is provided with central locking system, where in the three drawer are locked with one key.PVC recessed handles are provided for easy opening and closing of drawer. The drawer unit is fitted on castors (optional) for easy mobility. PVC edge banding are imported from Rehau or Dolken of Germany. The complete furniture unit is factory assembled with knock down fittings. The pedestal is fitted with additional (5th) castor to avoid topplig of pedestal in case of opening of any / all of the 3 drawers.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . Postform top Back Storage-Prelam halfheight storage 900 mm X 425 mm X 740 mm.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 9mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding.The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. PVC edge banding are imported from Rehau or Dolken of Germany.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . Smart High back Chair.Fabric upholstered. Height adjustable 2 dimensional arm rest with PU Pads on arms.Synchro 1 with 1 positions of locking when back is erect. Nylon Base with 30% glass reinforced. 50mm Dia castors. 435 (Depth from lumber point to seat edge) X 490 (W). 470 (Height of seat to Back rest) X 470 (W).Nylon Base & Nylon Castors.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . Smart Visitor cantilever Chair .The back is made up of foam upholstered Ply having High resilience foam on the back. The complete back is contoured to provide the needed lumbar support for long seating hours. The seat is made up of moulded foam, upholstered with mesh fabric having high tensile strength. Back Rest :- 790mm High and 500mm Width, Seat :- 460mm width and 470mm depth, Seat to Back rest height :- 650mm.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . Prelam Storage 900WX425DX1200H body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 9mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding.The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. PVC edge banding are imported from Rehau or Dolken of Germany..The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . Kingsley Premium Main table 1650Wx750Dx740H with Side Table 1200WX450DX740H. Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with 2mm PVC edge banding with enhanced scratch resistance supported on 25mm thk. Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility. Wire routing / wire management groumets shall be provided on main or side table as specified by customer.Supply and Installation of . 2B1F Prelam Pedestal Unit of Dimensions 400W x 470D x 675H is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade. All the exposed edges are sealed with 2mm thick PVC Imported edge banding on sides and bottom. The top and drawer facia are sealed with 2mm thick PVC edge. The drawer unit consists of 2 box drawer and 1 file drawer. The sides of Inside drawer box are of prelam particle board. The drawer box is fitted with roller Slide for free movement. The drawer unit is provided with central locking system, where in the three drawer are locked with one key.PVC recessed handles are provided for easy opening and closing of drawer. The drawer unit is fitted on castors (optional) for easy mobility. PVC edge banding are imported from Rehau or Dolken of Germany. The complete furniture unit is factory assembled with knock down fittings. The pedestal is fitted with additional (5th) castor to avoid topplig of pedestal in case of opening of any / all of the 3 drawers.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . Smart Mid back Chair.Fabric upholstered. Height adjustable 2 dimensional arm rest with PU Pads on arms.Synchro 1 with 1 positions of locking when back is erect. Nylon Base with 30% glass reinforced. 50mm Dia castors. 435 (Depth from lumber point to seat edge) X 490 (W). 470 (Height of seat to Back rest) X 470 (W).The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . 2 Seater Team Up Student Table of size 1350Wx450Dx740H - Design: It is developed for Straight, Curved both in flat & steps flooring type which has to be grouted. Table top: 25mm thick prelam particle board confirming to IS 12823 with PVC edge banding Height: 740mm Understructure: 63mm dia pipe with necessary materials for grouting Grouting components in powder coating finish of 50-60 mircons DFT as per ASTM standard Legs: Specially designed for providing straight and curved class rooms Wire Management: Wire management provisions are provide for individual users Provision for wire management through the leg and 4 module switch mounting cut-outs provided for individual user. Space conditions: Straight Line seating arrangement for flat / step flooring Curved Hall Installation with Minimum radius of 5000mm to be considered Modesty 18mm thick BSL confirming to IS:12823, Accessories Pencil holder/name plate/ book shelf. The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . Salsa Chair with Arms, Made of round MS tubes. Rear legs Dia 25.4mm with 2mm thick and L-shape Front legs of dia 25.4mm with 1.2mm thick, all together will be welded with support of welding fixture. Understructure is metal powder coated to the thickness of 60 to 80 Micron.Glides will be fitted at the leg bottom of the chair. Seat and Back made of Polypropylene material with Hot Runner Mould Technology. Back will have metal insert and Spring washer bracket for fixing with understructure frame.Seat will be fixed to understructure by using bumper stacks and screws.Seat Height from floor = 455mm, Seat Depth = 459mm, Seat Width = 445mm, Total Chair Height = 811mm, Total Chair width = 512mm & Total Chair Depth = 553mm. PU Padded armrests. Glides are fixed at the bottom of the 4 legs for smooth movement of chairs on any surface.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of . Pep Visitor Chair, The chair frame shall made up of durable powder coated steel and polypropylene .High density moulded polyurethane padding used for seat. Fabric upholstery is used for seat and mesh is used for back frame. Chair is black in color. Seat dimensions should be 47.6 cm(W) x 46.6 cm(D) and back should be 44 cm(W) x 36.5 cm(H). Armrest is a part of the visitor understructure . The Visitor Understructure is available with castors and glides. Overall dimensions of Chair shall be, Width of Chair - 58.0cm, Depth of Chair - 57.5 cm as measured from pedestal below. Height from ground - min 81.5 cm. Seat height - min 45.5 cm. Dimensions tolerance / variations shall be within +/- 1 cm. Chair tested as per ANSI/BIFMA x5.1 standards.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of/. . Hangout Prelam Single Bed 1000W x 660H x 2025L.The legs are made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2mm. The legs should have corner brackets welded to it at two levels. The corner brackets are made of 2mm thick CRCA having a L shaped structure to join the side panels and headboard to the leg. Three nos. of Horizontal stiffeners are provided at equal intervals. The stiffeners are made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2mm. The middle Horizontal Stiffener has a leg attached to it to transfer the load to the ground and add to the strength and stability of the complete structure. This leg is also made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2mm. All Metal components to undergo 7 tank treatment process and should be powder coated to the thickness of minimum 50 Microns DFT.The head board is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The head board size to be considered as 1000 x 660mm.The side panels are made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The overall width of the side panel is 150mm. The side panels have 18mm thick prelam particle board Baton running for required length to add rigidity to the structure.The foot board is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The head board size to be considered as 1000 x 450mm.The Bed Base is made up of 12mm thick Prelam Particle Board with both side White laminate The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of/. . Hangout Bedside Table. Size 400W x 400D. The bed side unit is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The bed side table has one drawer and one shelf. The shelf is made of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and Installation of/. . WUDMATE Chair with arms, wooden chair made of red Miranti wood as per drawing. Back : Height: 1000 mm x Width: 425 mm Seat : Height: 450 mm x 480 mm. All wooden part will be as per drawing. Seat will be covered by foam wrapped with fabric as per required colour.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

Supply and installition of Stainless Steel Rectangular Dining Table with Round fixed chair Design :Design of Table- Rectangular, Design of fixed chair -Round Dimensions : Width of table - 1800mm for 6-seater Depth of table-915 mm Height of table-750 mm Table Leg size-25 mm Dia Chair/bench Leg size-25 mm x 25 mm Size of support pipes/square sections (for table)- 25 mm x 25 mm Size of support pipes/square sections (for chair/bench) - 25 mm x 25 mm Chair/bench seat width - 450mm Chair/bench seat height - 500 MM Material & Thickness : Table top / Chair seat / bench seat material - Stainless steel Grade 304 galvanized Leg material for Table and Chair/bench-Stainless steel Grade 304 galvanized Support material for Table and Chair/bench- Stainless steel Grade 304 galvanized Table - Chair/bench attaching material- Stainless steel Grade 304 galvanized Number of Legs in table-4 - legs Number of Legs in chair/bench- 3 - legs Warranty Period - 3 - year min. Product should be ISO9001:2015 certified

Supply and Installation of/. . Hangout Double Bed 2040Lx1600Dx758H , Understructure: - The legs are made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2mm. The legs should have corner brackets welded to it at two levels. The corner brackets are made of 2mm thick CRCA having a L shaped structure to join the side panels and headboard to the leg. Three nos. of Horizontal stiffeners are provided at equal intervals. The stiffeners are made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2mm. The middle Horizontal Stiffener has a leg attached to it to transfer the load to the ground and add to the strength and stability of the complete structure. The leg is also made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2mm. All Metal components to undergo 7 tank treatment process and should be powder coated to the thickness of minimum 50 Microns DFT.Side Panel: - The side panels are made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The overall width of the side panel is 150mm. The side panels have 18mm thick prelam particle board Baton running for required length to add rigidity to the structure.Head Board :- The head board is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The head board size to be considered as 1000 x 650mm.Tail Board :- The head board is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The head board size to be considered as 1000 x 450mm.Bed Base: - The Bed Base is made up of 12mm thick Prelam Particle Board with both side White laminate. The bed has a mattress having Bonnel Spring panel, spring steel 2.4 mm steel wire, 100 mm height,Cotton felt on top and bottom of the panel – 10 mm, 1000 GSM,Side foam – 40 mm, 40 Density .Top and Bottom – 20 mm, 28 density P U foam sheet,Single quilt top, bottom and side.Fabric – 130 GSM. The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.

PARKING SHED - TENSILE STRUCTURE

Supply,Design, Pattern ing, Survey , MS Pipes MS Plates, Fabric, Wire Rope , Cutting, Stitching, Welding, Pa i nt, Transport, Raw Materia l and Instal l ation. TECHNICAL SPECIFICATION: e Structure shall be made of Hallow M.S.Rou nd Square or Rectangular pipe. e One quote of Primer and two qu otes of PU Paint woul d be given. e Base p l ate and connecti on cli t wou ld b eused. e G l ca b l e wo u l d b e u s ed . e Struct ure sha l l be d esigned as per IS 875/ BS 5950/ BS 6399. e M em bra ne sha ll be considered for 700GSM Fabric Type e M em bra n e sha ll be cu t and gri n d ed with h igh freq u n cy PVC weld i ng machi ne.

MISCELLANEOUS WORKS ( Furnishing Items, Utility Items, etc.)

Supply and installation of Domestic Bathroom Mug as approved by E/I Material:Natural PP Food Grade quality Material:Yes Colour : Any colour & Patteen Shape:Oval Cylinder Capacity (ml):501-750 Weight of Mug (Grams) :51-75

Supply and installation of Plastic Bucket MULTICOLORED as approved by E/I Bucket body Material:Natural HDPE Food Grade quality material:Yes Capacity (Ltrs):16 liter

Supply and installation of SINGLE MATTRESS 6 INCH as approved by E/I. DIMENSION: 1981 mm X 914 mm, Number of Layers:Two Layers Thickness of Core Layer 1 :75 mm, Thickness of Core Layer 2:50 mm Material of Core Layer 1:PU Bonded Foam, Material of Core Layer 2:PU Foam QUILTING:One Side Quilting (Single Sided), Quilting Material:PU Foam, Density :18 Kg/m3, Thickness of Quilting:24 mm MATTRESS COVER: Fabric Composition-Polyester-Cotton Blended (80:20), Construction-Knitted, Fabric Mass ( Minimum )-240 gm/m2,FabricColour/Print/Pattern-Printed, Surface Finish of Mattress-Without Convolution Core Layer 1 Density-90 Kg/m3, Core Layer 2 Density-50 Kg/m3, Mattress Top-Box Type, Compression Set for PUFoam (non quilting) as perIS 7888 1976 (Max)-10%, Resistance to Ageing forPU Foam as per IS 7888latest (max)-Shall meet the requirement of IS 7933 Latest, Durability Test for PUFoam as per IS 7888 latest-Shall meet the requirement of IS 7933 Latest, Durability Test forComplete Mattress-loss of height not more than 13 mm (as per ASTM 1566), Warranty-5 Year.

Supply and installation of QUEEN MATTRESS 6 INCH as approved by E/I. DIMENSION: 1981 mm X 1524 mm, Number of Layers:Two Layers Thickness of Core Layer 1 :75 mm, Thickness of Core Layer 2:50 mm Material of Core Layer 1:PU Bonded Foam, Material of Core Layer 2:PU Foam QUILTING:One Side Quilting (Single Sided), Quilting Material:PU Foam, Density :18 Kg/m3, Thickness of Quilting:24 mm MATTRESS COVER: Fabric Composition-Polyester-Cotton Blended (80:20), Construction-Knitted, Fabric Mass ( Minimum )-240 gm/m2,FabricColour/Print/Pattern-Printed, Surface Finish of Mattress-Without Convolution Core Layer 1 Density-90 Kg/m3, Core Layer 2 Density-50 Kg/m3, Mattress Top-Box Type, Compression Set for PUFoam (non quilting) as perIS 7888 1976 (Max)-10%, Resistance to Ageing forPU Foam as per IS 7888latest (max)-Shall meet the requirement of IS 7933 Latest, Durability Test for PUFoam as per IS 7888 latest-Shall meet the requirement of IS 7933 Latest, Durability Test forComplete Mattress-loss of height not more than 13 mm (as per ASTM 1566), Warranty-5 Year.

Supply and installation of Single Bed Cover as approved by E/I . Specification : Variety of Bedsheet/Bedcover-Bed Sheet/ Bed Cover, Count of weft-2/10s, Fabrics of Bedsheet Bedcover-Percale fabric,Washing-Machine Wash, Item Weight-900 gram,Types of Bedsheet/Bedcover-Single, Colour-As per requirenments, Ends per inch in inches-30-34,Count of warp(Cotton)-2/10s,Ideal for- elders, Picks per in inches-22-26,Size And Dimensions :Width-60 inch, Length-2.28 meter.

Supply and installation of Double Bed Cover as approved by E/I : Variety of Bedsheet/Bedcover-Bed Sheet/ Bed Cover, Count of weft-2/80s cotton, Fabrics of Bedsheet Bedcover-Combed cotton, Washing-Machine Wash, Ends per inch in inches-72-76, Count of warp(Cotton)-2/80s, Picks per in inches-44-48, Pattern of Bedsheets-Floral, Size And Dimensions- Width-90 inch, Length-2.28 meter.

Supply and installation of Pillow as approved by E/I : Conforming to Standrads:DGQA Prov Specn No. S/1706/Synthetic Pillow/ TC-6, DIMENSIONS:Length-700 millimeter, Width-400 millimeter, Height of pillow at center-170 millimeter, Body fabric-Cloth plain weave Polyester cotton (67:33) white, Ends per cm-40, Picks per cm-30, Body fabric mass (g/square mtr)-110 gram, Filling Material-Hollow siliconised polyester , Mass of filling material (g)-625 gram, Total mass of syntheticpillow (g)-715 gram, Reinforcing/ Piping-Shroud laid cotton line of 2 mm dia

Supply and installation of 10 LTRS. HDPE Waste Container as approved by E/I : Utility-Domestic, Material-HDPE, Bin Capacity (Volume) (Ltrs)-10 Litres, Wall-Non- Perforated, Lid-removable, Without Wheel, Towage Provision-no, Weight of Dustbin(Complete unit) (Grams)- 310 , Load carrying Capacity-10 KG, UV Resistant- YES.

Supply and installation of 40 Litres LLDPE waste containersor as approved by E/I : Utility-Domestic, Material- LLDPE, Bin Capacity (Volume) (Ltrs)-40 Litres, Wall-Non- Perforated, Lid-SWING TYPE, Without Wheel, Towage Provision-no, Weight of Dustbin(Complete unit) (Grams)- 390 , Gripping Provision- Frontal, UV Resistant- YES.

Supply and installation of 1100 Litres LLDPE waste containersor as approved by E/I : Utility-Public (Mobilecontainers container confirming IS:12402, Material- LDPE, Bin Capacity (Volume) (Ltrs)-1100 Litres, Wall-Non- Perforated, Lid-Hinged, With Wheel, Towage Provision-Yes, Weight of Dustbin(Complete unit) (Grams)- 130000 APPROX , Gripping Provision- Both Frontal &Ventral, UV Resistant- YES., Class confirming to IS 12402 - Type B (with 4 pivoting castors), Wheel Dimension in (mm)(Diameter x Thickness )(mm x mm)-200 x 50, Load carrying Capacity(Kgs)- 1000 Approx, Wheel Material- Solid Rubber, No. of Compartments inthe Bin- single.

Supply and installation of 60ltrs/hr water Cooler as approved by E/I : Cooling Capacity Litres/Hour-60Liters/hour, Storage Capacity-120 liter, Warranty on Machine-2 year, Warranty on Compressor-2 year, Maximum EnergyConsumption (Watt)- 775 Watt for 60 ltr/hr cooling cap., Conformity to Indianstandard-IS: 1475 latest, ISI MARKED- Yes, Eco-Friendly (Non CFCRefrigerant)-Yes, Water Tank sheet materialand thickness- Stainless Steel (Grade AISI 304), thickness > =0.8 mm, Water Tank cover and lidbottom Sheet material- High Impact Polystrene(HIP), Water Tank cover and lidbottom Sheet Thickness-1.5 millimeter, Cooler Cabinet sheetthickness- 0.8 millimeter.

Supply and installation of 150ltrs/hr water Cooler as approved by E/I : Cooling Capacity Litres/Hour-150 Liters/hour, Storage Capacity-150 liter, Warranty on Machine-2 year, Warranty on Compressor-2 year, Maximum EnergyConsumption (Watt)- 1550 Watt for 150 ltr/hr cooling cap., Power Factor- 0.9., Conformity to Indianstandard-IS: 1475 latest, ISI MARKED- Yes, Eco-Friendly (Non CFCRefrigerant)-Yes, Water Tank sheet materialand thickness- Stainless Steel (Grade AISI 304), thickness > =0.8 mm, Water Tank cover and lidbottom Sheet material- Al. sheet, Water Tank cover and lidbottom Sheet Thickness-1.5 millimeter, Cooler Cabinet sheetthickness- 0.8 millimeter, Warranty on Machine-2 year, Warranty on Compressor-2 year

Supply and installation of Ceramc Flower POTS sas approved by E/I : Material- Ceramic, Shape (When viewed fromTop)-Square, Usage- Outdoor decoration, Suitable for Watering- Yes,Colour-GREY/ WHITE/ RED , Bottom Tray-Yes, Artistic /Decorative work onPots-Yes Pot Length (Diameter)- 812 millimeter, Pot Width (Diameter)-300 millimeter, Pot Height (Overall Height)- 432 millimeter, Capacity-15 liter, Weight of the Pot- 5 kilogram

Supply and installation of Vertical Blind sas approved by E/I : Head rail - end caps - carrier trucks with link - mono command with wand - face fix brackets - shallow frame face fix brackets -top fix brakets screw-top fix bracket springs - top fix brackets clip and screw - adjustable face fix brackets- extension top fix brackets-side fix brackets-louvre insert, cord-metal chain no.-6-plastic chain no. 6. - cord weights Arrangement of slatsalignment mechanism inthe slat traveller- Yes, Arrangement to replacedamage hook withoutdismantling the head rail- yes, Arrangement of clutchmechanism – to turn theslats- Yes (Worm Gear Clutch Mechanism ), Type of head rail-Regular, Material - PVC, Thickness of blindsmaterial (± 5%)-1 mm, GSM of blinds material tobe declared (in GM persquare meter)- 200, Material for head rail-Aluminium, Material for end caps-Nylon, Material for carrier truckwith link-Unit - nylon and link– stainless steel 202, Material for Monocommand with wand-Unit – nylon and wand – glass , Material for face - SS 202, Material for shallow frameface -SS 202, Material for top fix bracket screw-SS 202, Material for top fix spring- SS 202, Material for top fix bracket clip and screw- Nylon, Material for adjustableface fix bracket-SS 202, Material for extension top fix bracket- SS 202, Material for side bracket -SS 202, Material for louver insert- Nylon, Material for cord- Polyester, Material for metal chain- Nickel plated brass, Material for plastic chain-Polyester cord acetal spheres, Material cord weights-Barium sulphate,

Dimension for end caps- 67 mm X 17 mm X 10 mm, Dimension for carriertruck with link-24 mm X 32 mm X 12 mm, Dimension for monocommand with wand-67 mm X 17 mm X 10 mm, Dimension for face fixed bracket-20 mm X 51 mm, Dimension for louverinsert- 89 mm X 9 mm, Diameter of cord-2.0 mm, Diameter of metal chain-2.0 mm, Diameter of plastic chain-2.0 mm, Dimension cord weights- 110 mm X 30 mm X 16 mm, Colour of vertical blinds - as per E/I, Slat FINISHING- Fully welded-in weights, Warranty periods- 2 YEARS

Supply and installation of Acrylic name Plate as approved by E/I : Material of Nameplate- Acrylic, Base Material- Acrylic, Mounting- Through Studs, Colour of Nameplate- white, Size of Nameplate (cm xcm)- 20X30, Thickness of Nameplate(mm)- 4, Type of Lettering- Engraved, Colour of Lettering- blue, Maximum Number ofLetters on Nameplate(Nos)- 75

Supply and installation of 45 to 52 L 3 Star Direct CoolSingle Door Mini Refrigerator as approved by E/I : Conformity to IndianStandrad-IS:1476 latest for Direct Cool, ISI marked- Yes, Storage Volume(NETCAPACITY) (Litres)-45 to 52, Type of Door-Single, Insulation-Polyurethane, Built in Voltage Stabilizer-Yes, Method of Defrosting-Direct Cool, -3, Eco-friendly refrigerant- yes, Compressor- Power saver Compressor, Voltage Range at 43degree Centigrade (Volts)-230 (tolerance 10%), Coil Material- Copper (Cu), Type of Finish- Metallic