PROVISION OF PUMP HOUSE AND RCC UG SUMP 100000 LTR CAPACITY ALONGWITH CONNECTED ITEMS AT PASTA LANE UNDER GE NW NOFRA COLABA MUMBAI

Amount

Submission of detailed drawing (plan, section, elevation, side views) structural, electrical, architectural drawing For Pump House and RCC UG Sump (100000 Liter Capacity) designed by structural consultant as recommended by Garrison Engineer and duly vetted by IIT/Government engineering college/ NIT or VJTI Parel Mumbai.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out any type soil and circumstance all a specified and directed.

Excavating over areas, n exc 1.5 m deep and getting out any type of soil and circumstance all as specified and directed.

Excavating over areas, exc 1.5 m deep and not exc 3m and getting out any type soil and circumstance all as specified and directed.

M&L for hardcore of broken stone or boulders, gauge exc. 63mm but n exc 10mm , deposited, spread and leveled in layers not exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in foundation all as specified and directed

M&L Reinforced cement concrete 20 mm graded aggregate(design mix M-30) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L Reinforced cement concrete 20 mm graded aggregate (design mix M-30) Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters incl provinding 0.30m aluminium sheet on each joints and butt complete all as specified and directed.

M&L Reinforced cement concrete 20 mm graded aggregate (design mix M-30) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia & over cut to length bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and bending with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Use & waste Formwork to sides of concrete rough finished concrete for curved foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work, vertical or to batter all as specified and directed.

Use & waste Formwork to sides of concrete rough finished concrete for curved walls, retaining walls, abutments, parapets and staircase railings and similar work incl attached pillasters, buttresses, etc vertical or to batter all as specified and directed.

Use & waste Formwork to sides and soffits of suspended smooth finished concrete for curved for slabs such as roof slabs, floor slabs, landings and similar work; exceeding 200mm thick (Horizontal or sloping) all as specified and directed.

M & L for brick work in CM 1:6 with sub class B brick straight are curved on plan exc.6m mean radius all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, mixed with water proofing admixture (ISI marked) as per manufacturer’s instructions, complete all as specified. (Note : - Water Proofing compound shall be measured and paid for separately) all as specified and directed.

Supply only liquid water proofing compound (ISI marked) all as specified and directed.

M & L rendering in CM 1:4 on walls 15mm thick on fair faces of brick work finished the surface even and smooth with out using extra cement complete all as specified and directed.

M & L 10mm thick cement plasters in CM 1:6 on concrete or brick wall fair/other than fair surfaces finished even & smooth with out using extra cement all as specified and directed.

M&L PCC 1:3:6 nominal mix M-10 grade using 40 mm graded crushed stone aggregate as in PCC Curb surface finished fair and even complete all as specified.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25cm in soft / loose soil complete all as specified& directed.

Removing excavated material to a distance n exc 50 m and depositing where directed at a level n exc 1.5 m above the starting point.

M&L for two coats of cement based paint over a coat of primer including preparation of Newly plastered surfaces complete as specified.

M & L for preparation of new wall surfaces and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and directed.

M & L for preparation of new ceiling surfaces and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and directed.

M&L for 25mm thick Cement concrete type B-1, 1:2:4 (20mm graded stone aggregate)

M & L for non skid ceramic coloured floor tiles exc 0.11Sqm but n.exc 0.18 Sqm including bedded and jointed in neat cement slurry and pointed with white cement with pigment to match the shade of tile over 15 mm thick screed bed in CM 1:6 all as specified and directed.

M & L for glazed ceramic coloured wall tiles 450X300 mm including bedded and jointed in neat cement slurry and pointed with white cement with pigment to match the shade of tile over10 mm thick rendering in CM 1:4 all as specified and directed.

Supply and fix vitreous china water closet pedestal pattern complete with seat cover fixed to floor including trap set in concrete complete all as specified and directed.

S & F 10 litre capacity PVC flushing cistern low level, white, with inlet, ball valve, float and handle 32 mm dia flush pipe including brackets etc complete all as specified and directed.

S & F 15mm dia PVC connector with PTMT nuts of length 450mm completeall as specified and directed.

S & F Bib tap 15 mm CP with crutch or butterfly handle screwed down srewed for iron pipe or for brass ferrule and fixed all as specified and directed.

S & F 15 mm fancy type Angular stop cock CP with wall flange all as specified and directed.

S & F 15mm dia concealed fancy type stop valve copper alloy with chromium plated fixed to iron pipe all as specified and directed.

S & F aluminium butt hinges medium weight 75mm type C 21 in size for PVC doors all as specified and directed.

S & F aluminium butt hinges medium weight 100mm type C 21 in size for PVC doors all as specified and directed.

S & F aluminium anodised barrel tower bolt 150 mm of Extruded Section all as specified and directed.

S & F 150 mm aluminium handles cast type anodised all as specified and directed.

S & F G I tubing medium grade, galvanised with all fittings and fixed complete to wall and ceiling or laid in floors bore of tube 15mm all as specified and directed.

S & F G I tubing medium grade, galvanised with all fittings and fixed complete to wall and ceiling or laid in floors bore of tube 20mm all as specified and directed.

Supply , hoisting and fixing in repair Rotational moulded PVC water storage tank, 500 litres capacity conforming to IS-12701 (1989) cylindrical vertical type tripple-layered with closed top including inlet,PVC float valve and necessory fittings outlet and wash out holes of approved make including dismantling or existing tank of any description and removing from site of work complete all as specified and as directed.

S & F Solid PVC doorframe 50mmX47 mm made out of 5 mm plain coour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification and drwawing all as specified and directed.

Factory made solid panel PVC door shutter30 mm thick style consisting of frame made out of MS tube for top and bottom MS frame shallbe covered with heat moulded plain colour PVC C channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail& bottom rail with suitable PVC sheet beading and joined together with solvent cement supplying fixing in the frame at site as per specification and drawing all as specified and directed.

S & F 250mm long ( dia of shoot not less than 16mm) aluminum alloy anodized sliding door bolt( with hasp, staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolt of extruded section or cast aluminum all as specified and directed..

S & F 110mm bore PVC (SWR) pipes single socked in any length with rubber ring joints fixed to walls all as specified and directed.

S & F 75 mm bore PVC (SWR) pipes single socked in any length with rubber ring joints fixed to walls all as specified and directed.

S & F PVC (SWR) bends 110mm dia all as specified and directed.

S & F PVC (SWR) 110 mm junction (SingleT)equal or unequal 110 mm all as specified and directed.

S & F PVC (SWR) bends 75mm dia all as specified and directed.

S & F PVC (SWR) 75mm floor trap, plain with gratting, including jointing with solvent cements

S & F PVC (SWR) 125/110mm gully traps setting and including jointing with solvent cements

M & L II class hard wood plain solid straight chowkats and frame wrought, framed rebated on the solid put together with glue, pinned at joints and fixed in position complete all as specified and directed.

M & L for 30mm thick 2nd class hard wood panelled shutter two pannel with lock rail and pannel of 9 mm ply or 12 mm veneered particle boardwith commercial veneer on both side and fitted to chowkat all as specified and directed.

M & L for 35 mm thick 2nd class hard wood glazed shutter divided into square with plain,chamfered or rounded mitered and rebated sash bar any numbers, fitted with cut and mitred beads for securing glass etc and fitted to chowkat all as specified and directed.

M & L for preparation of new wood and wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of pink primer complete all as specified and directed.

M & L for preparation of new steel surfaces of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F powder coated (colour of coating as directed) aluminium (minimum 25 micron thickness of coating) of various section as required/suitable for doors, window & partion/Ventilator (sliding /or openable type)etc including fixing and making the frames hinges to receive glass/wire gauge etc. Complete incl all fittings like jointing cleat angles, aluminium powder coated aluminium glazing clips, rubber neoprene packing, CP brass /stainless steel screws etc. rubber beading, clips locking arrangement, handle, sealant etc all as specified and as directed.

S&F powder coated aluminium grill with and including suitable powder coated aluminium anodised frame F/H section as requird manufactured by M/S Decogrill as per design No DG- 104, 7.5 mm thick all as specified and as directed .

Hardcore of broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 type D2 Using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

Material and labour for PCC (1:2:4) type B1, using 20mm graded stone aggregate as in coping, kerb stone pcc or similar places etc complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block having glossy finish shape and size as approved by GE confirming to IS 15658-2006 of 80mm thickness, M-40 Grade of with grey cement and pigments laid over and including 50 mm thick dry sand cushioning and voids filled with dry and surface compact, including compaction by means of surface vibrator complete all as specified and directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; rungs; steel cover to tanks; welded framework of water tanks and similar work conforming to Fe.290.Gde-E- 165.

Supply, laying, jointing and testing LT under ground cable XLPE insulated and armoured and PVC sheathed 1100 volts grade, heavy duty with multistranded aluminum conductor of size 120 sqmm 3.5 core laid in trenches/ducts/ along poles/through pipe under road etc with new aluminum lugs complete all as specified and directed

Supply, laying, jointing and testing LT under ground cable XLPE insulated and armoured and PVC sheathed 1100 volts grade, heavy duty with multistranded aluminum conductor of size 25 sqmm 3.5 core laid in trenches/ducts/ along poles/through pipe under road etc with new aluminum lugs complete all as specified and directed

M&L for cutting of Road/hardstanding not less than 30 cm in depth and 30 cm in width underneath the road for passing the cable/pipe and making good with PCC 1:2:4 type B-1(using 20mmm graded stone aggrigate) whete road cutting done to make the road surface fair and level complete all as specified and directed by Engr-in Charge.

S&F HDPE of Pressure rating 6kg/cm sq pipe of 40 mm dia including necessary bends,elbows,Tees etc on cable protection complete all as directed.

S&F HDPE of Pressure rating 6kg/cm sq pipe of 90 mm dia including necessary bends,elbows,Tees etc on cable protection complete all as directed.

Excavation in trenches not exc 1.5 mtr wide & not exc 1.5 mtr in depth: for foundation etc or for manholes, laying of pipe in any type of soil and getting out complete all as specified

Supplying, fixing, jointing and testing mild steel MS black pipe with flanged ends ISI Marked, Fe 410 grade as per IS:1239/2004 nominal bore 150 mm, medium grade (Class B) in standard length of 5.50 - 6.00 meter, complete incl jointing materails such as nuts/bolts/washers/rubber gaskets etc all as specified and as directed.

S&F 80mm bore medium grade steel tubes galvanized with all fitting including cutting threading connection in new or old position for laid in trenches/wall/ceiling/ floor, all as specified and directed .

S&F 50mm bore medium grade steel tubes galvanized with all fitting including cutting threading connection in new or old position for laid in trenches/wall/ceiling/ floor, all as specified and directed .

S & F gunmetal globe or gate valve with iron wheel head, screwed both ends for iron pipes 80mm bore as in repairs complete all as specified and directed by Engineer – in – Charge.

S & F gunmetal globe or gate valve with iron wheel head, screwed both ends for iron pipes 50mm bore as in repairs complete all as specified and directed by Engineer – in – Charge.

S & F Ductile iron foot valve flanged type of size 80 mm dia complete incl all jointing materials such as nuts, bolts, washers, rubber gaskets etc complete all as specified and directed. .

S & F Ductile iron non return valve with flanged ends of size 80 mm dia complete incl all jointing materials such as nuts, bolts, washers, rubber gaskets etc all as specified and directed.

Supply, install, testing and commissioning of 5 HP monoblock pump set , 415 V 3 Phase, minimum 18 m head and discharge not less than 1600 LPM, complete with locking arrangement inside pit, including fittings like flanges etc, complete all as specified and directed.

Supply, laying, connecting and testing of PVC insulated and PVC sheathed copper conductor cable 3 core 6 sqmm 1100 volts grade alongwith copper thimble complete all as directed.

Supply, install, testing and commissioning of Starter cum LT panel made out of CPRI approved 3.0 mm thick CRCA sheet, dust and vermin proof with angle iron base frame and legs of size 50x50x6mm, PCC 1:2:4 type B-1 for grouting of base, suitable for 3 Phase 415 V 50 Hz complete with incoming of MCCB 4 pole 63 Amps 10 KA (incoming) MCB TP 16Amp C-Curve -03 Nos, DOL starter suitable for 5HP-02 Nos , LED indication lamp RYB, Multifunction meter along with set of CTs, cable entry glands, Earth teaminal, complete all as specified and directed.

Material & Labour for Earthing with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick, burried directely in ground (earth pit not less than 2.5 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised iron strip 32 x 6 mm with the help of bolts, nuts, check nuts and washers of galvanised iron or steel, including necessary excavation, PCC 1:3:6 type D2 and PCC cover 1:2:4 type B1 watering arrangement with GI pipe funnel, jali, and cast iron cover fixed on top of pit complete all as specified and shown in electrical plate No.3 including connection to the earthing test point and testing on completion.

S & F Foundation bolts 600 mm long for pump sets made from 20 mm dia MS rod duly threaded at top upto 200 mm length with and including two MS nuts and 3 mm thick washers complete all as specified and directed.

Cuttng of existing CI/GI pipe in position for inserting of tee, bend collar other type of CI/DI fitting for addition /alternation of existing system for150mm bore

Suply and fix PVC float valve 50 mm (ISI marked ) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwwed for iron pipe and fixed. ( Minimum weight 40mm- 690 Grams 50mm- 830 Grams including necessary GI fittings such as elbow, reducer, nipple etc complete all as specified and directed by Engineer-in-Charge.

M & L for point wiring confirming to IS-732:1989 complete with 1.5 sqmm single core multistranded FRLS PVC insulated unsheated copper conductor,1100 volts grade confirming to IS-694:1990 drawn through and including rigid non-metallic PVC medium grade concealed conduit of suitable size having thickness not less than 1.2mm ISI marked with accessories concealed in wall/floor including cutting chases, pining etc with modular metallic ISI marked terminal boxes, concealed in wall including one FRLS PVC insulated and unsheathed multistranded green colour copper conductor 1.5 sqmm as earth continuity conductor connected to common earth as earth dolly complete all as specifed and directed.

(a) One light point controlled by one switch SP one way.

(b) One exhaust fan point controlled with one 5A switch

(c) One 3 pin socket outlet 5Amps on independant board.

S&F Modular Switch , 6Amp, One way, 1 module, ISI marked.

S&F Modular Socket , 6 Amps, 2/3 pin combined 2 module, ISI marked.

S&F Modular white cover plate with Frame 3 Module, ISI marked.

S&F Modular white cover plate with Frame 8 Module, ISI marked.

S&F Modular metal flush box 3 module, ISI marked and incluing cutting hole in wall / ceiling/piller etc and making good surface.

S&F Modular metal flush box 8 module , ISI marked and incluing cutting hole in wall / ceiling/piller etc and making good surface.

Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing exhaust fan , plastic body AC single phase, 230 volt of size 250 / 300 mm sweep 1200 RPM with blades, and frame and louvers complere fixing arrangements on the wall with nuts and bolts making the good surfces all as specifed and directed.

S&F of New LED Bldg security light 45 Watt indus series powder coated pressure die cast aluminium high power LED bldg security light with heat resistant toughned glass with lens with IP66 Protection including 40 mm dia pipe bracket , complete all as specified and directed by Engineer-in-Charge.

S&F ceiling rose surface bakelite with ISI mark, three terminals complete all as specified and directed.

GANGAJAL (BID ID -3426268)

Unitech Enterprises (BID ID -3425521)