Earth filling in open area and Furniture for New Building of RSSOCA, Baran Distt. Baran against saving the work Construction of Office Building of RSSOCA Baran Distt. Baran

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in: Cement Mortar 1:6 ( 1-Cement : 6-Sand).

Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per MoRTH Specification Clause 201. (ii) By Mechanical Means In area of non-thorny jungle

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300-1 and 300-2 with a lead upto 50 m as per MoRTH Specification Clause 305.3

Earth, Sand, Lime, Morrum manure or sludge, Add for each 1 Km beyond 5 Km (upto 10 Km.)

Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete: 20 mm

Supplying and fixing Rollor Blinds of good quality and approved make made out of Imported fabric including Roller Mechanism and lock with chain system with all necessary hooks etc. complete as per direction and sample approved by engineer-in-charge.

Supply , Installation, Testing and Commissioning of Inverter type Air cooled Hi Wall split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R- 407 Green Refrigerant, wireless Remote control, suitable for working between 180-260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. The system shall be able to deliver 100% of the rated capacity up to 42 Degree Celsius ambient temperature. Min 5 year Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB). Must comply : Electrical cable IS 694 or IS 9968 temperature sensing control IS /International Electro technical Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993 and motor IS 12615. Complete as per specification and IS : 1391 Part II 2023. The system shall be able to operate up to 50 degree C (out door ambient temperature) Cooling capacity 3400-3500 Watt, ISEER not less then 4.6

Supply, Fixing and testing of following capacity IS:8448 marked wall mounted stabilizer having output voltage variation from 200 V to 250 V(+/-5%) with input voltage variation from 170 V to 260 V, time delay facility from 2 to 4 minute and high cutoff at 270 V with providing of 16 Amp /20 Amp Industrial plug top making connection etc complete in all respect. 4 KVA

Supply & fixing MS powder coated stand suitable for 1.0/1.5/ 2.0 Tr outdoor type of Split AC. All as per pre approved by Engineer in charge.

Making hole in stone masonary/ RCC wall/ RCC slab with core cutter for accomodating refrigerant pipe/ drain pipe/ MS pipe/ cables etc of following dia 50 mm dia per running inch length

Item Rate BoQ

BoQ_Ver4.0

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only)

NUMBER #

OFFICE HIGH BACK CHAIR SEAT/BACK ASSEMBLY: The Cushioned seat assembly consshould be ts of seat outer (material-30% Glass Fiber Nylon)& upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam & polyster fabric. The Net Back should be made up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) and upholstered using Polyester Mesh fabric with high tenacity yarn. Full Back Size: 46.5 cm. (W) x 60.0 cm. (H) Seat Size : 51.0 cm. (W) x 49.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density = 45 +/- 2 kg/m³ and Hardness load 12 +/- 2 kgf for 25% compression. BACK SPINE: The support spine should be made up of High Pressure Die cast polished hed Aluminum. ARMRESTS : The armrest should be having two adjustment, Height (6.0±0.5cm) and Depth (6.0±0.5cm). Height adjustment should be provided in Aluminum structure of armrest which should be connected to Aluminum Back spine and should be operated by button. The depth adjustment should be provided in pad which should be fixed to armrest structure. Armrest Top should be made up of PU molded over plastic inner. ACTIVE BIO-SYNCHRO mechanism: The adjustable tilting mechanism should be designed with the following features: • 360° revolving type • Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort • Tilt tension adjustment can be operated in seating position • 5 position Tilt limiter giving option of variable tilt angle to the chair • Seat / back tilting ratio of 1:2 • The mechanism housing should be made up of HPDC Aluminum & black powder coated (DFT 40 to 60 micron) SEAT EPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding echanism. Seat depth adjustment range should be of 3.75±0.1 cm LUMBAR SUPPORT ASSEMBLY: The Lumbar support assembly should consist of

lumbar spine (material-Glass Fiber Filled Nylon) which should be fixed to Aluminum Back spine. The Lumbar pad (material- Poly Propylene) should be fixed to lumbar spine through lumbar Pad support. Lumbar Support Assembly has height adjustment of 5.0±0.5cm PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3cm. PEDESTAL ASSEMBLY WITH CASTORS:The pedestal should be High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black PP having 6.0± 0.1cm wheel Diameter. The neckrest assembly consshould be ts of upholstered Neckrest inner(material-PolyPropylene) with moulded Polyurethane foam and Polyster fabric.Upholstered inner should be fixed to Neckrest cover.Neckrest should be fixed to Back assembly through Neckrest spine .Neckrest assembly has height adjustment of 5.5 +/- 0.5cm and Rotation adjustment of overall 20° +/- 2° Overall Dimensions of Chair Seat Height - min 45.5 to max 55.5cm. Height - min 95.5 to max 105.5 cm. Width & Depth of Chair as measured from pedestal - Width-75.0 cm and Depth-75.0 cm.

Almirah Plain Storwel plain shall have an overall size of 916mm(W)x486mm(D)x1980mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The Storwel Plain should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

PUBLIC SEATING CHAIR 3 SEATER The seat shell should be a welded assembly of seat,back and side frame. The seat and back should be made of 0.12±0.013cm thk CR steel sheet with oblong perforations.They should be welded to sideframe of size 3.2±0.05cm x 0.5 ± 0.05 cm thk HR steel.The welded assembly should be powder coated ( DFT 40-60 microns ). The seat has a front water fall edge to provide popliteal clearance for comfortable seating. It also has a buttock support curve that not only provides rear support but also prevents small children from falling through the gap between seat and back. Clean and flat surfaces of seat and back aids in easy maintenance. * SEAT SIZE : 47.8 cm (W) x 44.6 cm (D) * BACK SIZE : 41.6 cm (W) x 23.0 cm (H) Understructure assembly consshould be ts of connecting beam and leg assembly made of M.S. E.R.W. oblong tube of size 7.5±0.03cm x 2.5±0.03cm x 0.2±0.016cm thk.The welded structure assembly should be powder coated ( DFT 40-60 microns ).The leg assembly should be fitted with shoes and levellers in Nylon. The leg structure should be designed with minimal should be a of contact close to ground providing easy access for cleaning purposes. The shoes fitted to leg assembly help in aligning the structure for back to back arrangements. Levellers take cshould be of uneven flooring.Connecting beam should be fitted with snap locking end cap.lt also aids in side-by-side understructure alignment. Armrest assembly consshould be ts of armrest frame and armrest pad . The armrest frame should be made up of size 3.175±0.05cm x 0.47±0.027cm thk HR steel and it should be powder coated ( DFT 40-60 microns ). Armrest pad should be injection molded in Nylon and should be fitted onto the armrest frame. Overall Dimensions of Chair Seat Height - 44.1 cm. Height - 78.5 cm. Width & Depth of Chair as Width-169.5cm and Depth-63.8 cm.

Supplying and placing of modular office table wooden/pu 6'X4'and 2'6" hieght.Size make in 42mm th.prelaminated board base top and side support and other part of table 17mm th. Prelaminated board base comleted. Covered by 2mm th. PVC as bend pasted by glue /adhesive hot melt and trimming by auto as bend machine. Both side of table 15"X42"X28" side unit with storage and computer facility, locks, handles ete including cost of material and labour completed with all repect as per enclosed drawing and as per direction of Engineer incharge.

Supplying and placing of wooden table (ghana teak wood grade-1) 6'X3' and height 2'6" make 35mm th. plb wooden base top and Melamine polish. Wooden structure are 3"X3" square legs, 3"X1.5" Top and bottm cross wooden bars. including cost of material and labour completed with all repect as per enclosed drawing and as per direction of Engineer incharge.

Supply of Wooden Conference Chair (Ghana Teak wood grade-1) size 1'6"X1'6" seat and 1'6"X2'6" back.2"X2" legs and rest of structure 1.5" back wooden seat cushion foam with fabric and back wooden strip.with melamine polish. Including cost of material and labour completed with all repect as per enclosed drawing and the direction of Engineer-in-charge.

Supplying & placing cabinet with an overall size 750mm X 450mm X 600mm. The cabinet shall be made up of Pre- laminated particle board with approved laminate and finish as per approved shade. The top shall be made up of 25mm thick and other parts like side, back, shutter, facia, skirting shall be 18mm thick. The edges shall be scaled with thin strip of impermeable PVC. The storage shall be supplied with 2 nos. of shelves. Door shutters shall be provided for opening and closing the cabinet. Including cost of material and labour completed with all repect as per direction of Engineer incharge.

Please Enable Macros to View BoQ information