PROVN OF WASHROOM AT PAO (ORS) LEKHANAGAR, TWO RUNWAY CONTROLLER CABIN, PARKING SHED ADJACENT TO BLDG NO. T-02 OF 665 AVN SQN AND SPL REP TO OTHER RANK MD ACCN BLDG NO. P-81/01, 02, 04 TO 06 UNDER GE NASIK ROAD.

Amount

Surface dressing n exc 15 cm deep in soft/loose soil complete all as specified and directed.

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out soft/loose soil etc

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft soil complete all as specified and as directed.

Excavation in trenches in hard soil not exceeding 1.5 mtr deep and not exceeding 1.5 mtr wide for laying of cable, RCC poles / stays and struts etc. and getting out including trimming sides and forming bottom surface complete all as specified and directed at site.

Excavation in post holes (or similar holes) each in n exc 0.5 cum getting out and removing surplus soil to a distance in n exc 50 m and making good surface in soft/loose soil complete all as specified and as directed.

Returning, filling in including spreading, leveling, watering and well ramming excavated soil in layers not exceeding 25 cm thick each, back in trenches after cables have been laid and tested, poles, stays , struts have been erected and tested , all as specified and directed.

M&L for broken stone hard core of gauge n. exc. 63 mm deposited, spread and levelled in layers n. exc. 15 cm thick, watered and rolled / rammed to a true surfaces complete.

Removing excavated surplus soil (Soft/hard soil) obtained from excavation to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5m above the starting point, complete all as specified and directed.

M&L for PCC(1:4:8) type D-2 using 40mm graded stone aggregate in foundation mass concrete and filling complete.

M&L for form work to sides of concrete foundations,footings bases of coloumns raft and raft beams,sides and soffits (if any) of foundation and plinth beams, and similar work,vertical or to batter for rough finished surface of concrete complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

M&L for Formwork to sides of to faces of walls, retaining walls etc finished even & fairall as specified and directed.

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work n. exc 200mm thick (Horizontal or sloping) complete all as specified and directed.

M&L for form work to chajjas including edges or to batter for rough finished surface of concrete complete all as specified and directed.

M&L for form work to sides of pillars, posts,struts,piers,columns etc or to batter for rough finished surface of concrete complete all as specified and directed.

M&L for RCC M-25 (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams, bases for columns, etc, basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for providing reinforced cement concrete nominal Mix Type B1 (1:2:4) using 20mm aggregate for walls, retaining wall, ballast walls and the like etc using 20mm graded aggregates all as specified and directed.

M&L for RCC M-25 (using 20 mm graded stone agg) lintel beams, roof beams, cantilevers bressumers, lintels over 1.5m span complete all as specified and directed

M&L for RCC M-25 (using 20 mm graded stone agg ) slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for RCC M-25 (using 20 mm graded stone agg ) as in chajjas complete all as specified and directed.

M&L for RCC M-25(using 20 mm graded stone agg ) as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for 40mm damp proofing course in cement concrete 1:2:4 Type B-0,horizantal or vertical surface including necessary formwork.

M&L for Deformed steel bars TMT 10 mm dia and over cut to length bent to shape required including cranking bending spirally for hopping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confiring to Fe-410 complete all as specified and directed.

All as per item No. 23.00 but 5mm dia and over upto and incuding 10mm dia in stirrups tie, spacers and binder complete all as specified and directed.

M&L for moorum filling under floors or paving laid in layers n.exc 15cm thick, spread , levelled and rammed including watering complete all as specified and directed by Engr-in-Charge

M&L for 15 mm thick cement screed bed in CM 1 : 6 for fixing of tiles complete all as specified and directed.

M&L for Non Skid glazed ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 Sqm, in floors set and jointed in cement slurry and pointed in coloured cement complete all as specified and directed.

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match

M&L for 75mm thick cement concrete 1:3:6 type C-2 (using 40mm graded stone agg) as in plinth protection laid to slope of 1 : 12 and finishing cement concrete surface even and smooth without using extra cement with and including all necessary form work to divide the area in panels finishing exposed edges fair or rounding or chamfering of exposed edges where directed and providing 6 mm thick joints through the thickness of plinth protection duly filled with mastic filling of one part of hot bitumen 85/25 grade and three parts of fine sand (all by weight) complete all as specified and directed.

M&L for rendering 15mm thick in CM 1 : 4 on roof surfaces finished even and smooth with extra cement complete all as specified and directed using waterproofing compound @ 3% by weight of cement complete all as specified.

Supply only integral waterproofing compound

M&L for Waterproofing on roof including flashing and junctions of parapet,kerb, wall etc.as under :- (a) Cleaning of plasetered roof,parapet,facia surface and applying one coat Oil based cold bituminous primer @ 0.70 kg per sqm. (b) Laying a layer of APP based polymeric membrane,3 mm thick(minimum),weighing not less than 3.60 kg/Sqm prefabricated fire layer waterproofing membrane reinforced with polyester non woven fabric(weighing not less than 160 gms/sqm) shall be applied over compatible primer at 0.40 litre/Sqm of density at 25 degree Centigrade 0.87-0.89 Kg /Litre and viscosity 70-160cps or cold sticker, application of APP modified membrance shall be by torch application. The overlaps shall be minimum 150mm on the transverse direction and 100 mm on the longitudinal direction. (c) Painting the exposed APP membrane surface with bitumastic aluminium paint @ 0.15Kg/Sqm. (d) APP membrance,Primer and bitumastic aluminium paint shall be of same brand. (e) For vertical surfaces i.e. parapets,wall etc. app membrane shall be tucked into groove and sealed with silicon sealant i.e. "Dowsil 789 weatherproofing silicon sealant" using gun.

M&L for 15 mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces finished fair and even complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:6 on other than fair face of brick work or concrete surface complete all as specified and directed.

M&L for rendering 5 mm thick in CM 1:4 concrete surfaces of ceiling, chajjas etc. complete all as specified and directed.

Dismantling of steel window/ventilators any description and any size complete all as specified and directed. Note:work is to be executed for high rise bldgs.

S&F aluminium (minimum 50 micron powder coated) frame for doors, windows, ventilators and glazed partion frame of any size with one or more rebates including joining cleat,beading and connected accessories as required for fixing etc. complete all as specified. Note:work is to be executed for high rise bldgs. Note: (a) Work is to be executed at any height and situation. (b) During fixing of frames, surface shall be make good in plumb with existing finishes like cement plaster ,similar wall tile,floor tile etc and as per site requirement.

S&F aluminium (minimum 50 micron powder coated) window and ventilator shutters, side hung/sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings complete all as specified.

M&L for powder coated aluminium window or ventilator with shutters frame made with section 44x44x2mm thick style rails of shutters with section 44x44x2mm thick including 10mm size aluminium butt hinges 02 Nos in each leaf, 5mm thick tinted glass pane as inserted including jointing cleats, glazing clips, rubber packing aluminium anodized beading, screws etc; aluminium tower bolts 100mm size each leaf, hooks and eyes ‘D’ fabricated aluminium handles 100mm size, frame fixed in openings with hold fast of 25x3mm flats, 150mm long 04 Nos in each frames including cutting holes in brick work and embedded in PCC (1:2:4) bed block size 150x150x150mm each and match the existing surfaces complete all as specified and directed.

S&F 3.0 mm thick sheet glass, ordinary quality and glazing with silicon gel in square n exc 0.5sqm in each pane.

S&F solid PVC frame of size 50 x 95 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS suare tube , with necessary arrangement for fixing of glass for louer type window / ventilator and additional PVC beading around the frame for fixing of wire mesh

M&L for 3mm thick sheet figured glass,pin headed type where is required in squares n.exc. 0.5 Sqm in each pane. Height upto four storey buildings.

S&F Framed work as in grill, doors or gates of angle or other section with gusset plates, braces, etc, complete, drilled for fixing of steel sheeting or other covering, Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing Fe Grade 290(Gde E-165) complete all as specified and directed by Engr-in-Charge.

M&L for Preparing new untreated steel or iron surfaces over 10cm width or girth and two applying coats of synthetic enamel paint over and including a coat of red oxide.

S& F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar.

M&L for Granite (of any type) work 20mm thick machine cut, (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like laid over and including 15mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match.

M&L for Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations. (Stone slabs so provided shall be not less than 900mm in length)

S & F in repairs Sink made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm.

Supply and fix 15 mm Gun metal,globe or gate valves,(ISI marked ), with iron wheel head screwed both end for iron pipe and fixed for (externally threaded),for iron pipe or for union a fixed of following sizes :-

M&L for cutting/ drilling existing pipe line & taking branch connection complete incl all necessary GI fittings, jointing materials, earth work etc

Taking up or down steel tubing and connections 15mm bore including bib taps, stop cock etc.

Refixing old steel tubing and connections 15mm bore in new or old position (Walls, ceiling, floors, etc.)

S&F 15mm bore galvanised steel water tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors. Note: GI tubing shall be concealed wherever directed by Engr-in-charge. Contractors quotated rates deems to be inclusive of the said provision.

Taking up or down steel tubing and connections 20mm bore. (Note:work is to be done in multistorey bldgs(int and ext plumbing).

Refixing old steel tubing and connections 20mm bore in new or old position (Walls, ceiling, floors, etc.) Note: GI tubing shall be concealed wherever directed by Engr-in-charge. Contractors quotated rates deems to be inclusive of the said provision.

S&F 20mm bore galvanised steel water tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors. Note: GI tubing shall be concealed wherever directed by Engr-in-charge. Contractors quotated rates deems to be inclusive of the said provision.

S&F in repairs 15mm bore bib taps, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in repair.

S & F in repair 15 mm bore fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed.

S&F in repairs 15 mm bore stop valves, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed.

S&F in repairs Brass chromium plated shower rose 125mm size with swivel joint, including fixing to steel pipe or union 15mm bore.

S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm

M&L for brass CP angle cock heavy duty 15mm dia capstan head complete all as specified and directed.BIS approved.

S&F fancy bib taps 15mm bore chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.specification as per SSR Part-I.

M&L for 20 mm dia gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe all as specified and directed.BIS approved.

M&L for bottle trap brass chromium plated screwed down high pressure screwed both ends for iron pipe of bore 32 mm or for union and fixed Make Jaguar or equivilent all as specified and directed.

S&F 32mm bore low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sqcm including fittings.

S&F in repair Vitreous China water closet squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests and P/S trap (excluding flushing cistern and flush pipe) complete including provision of lime concrete bedding.

S&F 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including flush pipe and brackets complete all as specified and directed.

M&L for counter wash hand basin of size 580x440 mm mounted on grannite and cuddapa with and M&L for granite platform of size 0.90 x 0.55m rested on 30 to 35mm thick cuddapa stone slab and two granite supported on tiled wall support edges rounded and chamferred complete job all as specified and directed by Engr-in-Charge.BIS approved.

S&F in repair vetreous china wash down water closet pan EWC (pedestal pattern), white (excluding flushing cistern and flush pipe) complete all as specified.BIS approved.

S&F plastic seat cover white closed pattern with flat bottom and cover with mild steel chromium plated or alluminium hinging device complete all as specified and directed.

M&L for Vitreous China urinals, half stall type (back or corner wall type), white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement;including brackets, flush pipe, CP urinal spreader, grating union, union and cap and discharge pipe; complete all as specified.

M&L for PVC Nahani trap with grating including incl joining to waste pipe dia of outlet 75mm fixed in cement concrete type B1, (1:2:4) all as specified and directed

S & F in repairs Vitreous China wash basin white, flat back, size 550 X 400mm, including cutting for and pinning in ends of brackets or erecting stand, with and including 32mm waste fitting brass, chromium plated with long screwed shank and fly-nut, flange end bedded in red lead cement, brass chromium plated bottle trap with inlet and outlet screwed for pipe or connections 32mm bore, including necessary packing, union and cap and fixed in repairs.

S&F of rotational moulded polyethylene water storage tanks of 1000 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position over and including 20 mm dia float valve of brass complete all as specified in SSR 2009 Part-I all as specified and directed.

M&L for PVC (SWR) floor trap(75 mm dia), plain with grating including jointing with solvent cement to mitigate the site requirement to the entire satisfaction of engr-in-charge.

S&F in repairs brass chromium plated towel rail 20 mm outer dia `D’ type, 60 cm long between flanges with and including chromium plated brass screws and wooden / plastic cleats, complete. Make : Plumber Cat part No U-0911 MAL or equivalent in Marc

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long

S&F in repairs Brass chromium plated shower rose 125mm size with swivel joint, including fixing to steel pipe or union 15mm bore.

M&L for special treatment to sunken portion with 10mm thick plaster in cm 1:4 by using Dkitachment DM 1% by weight of cement and surface made smooth after curing period two coat of Ditachment DS shall be applied @ 2.5 Kg/Sqm. The paste like consistancy like is made by using 2.5Kg of Ditachment DS powder in one litre of admixture (The admixture is made by dissolving 1 part by volume of Nafufill SBR & 4 part by volume of water). After 7 days curing, testing shall be done by flooding for 72 hours. Finally protective plaster coat of 10mm thick in CM 1:4 shall done by using Putz Ditachment 1% by weight of cement over layer of Detachment DS. All joints of CI pipe, WC connection etc. shall be filled by mixture of cement, fine sand and 10% Nafufill SBR by weight of cement 32mm dia and 500mm long GI Spout light grade shall be provided in all sunken slabs to drain off water.including demolition of cement concrete in sunken slab and filling of mass concrete 1:5:10 all as specified and directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing debris out of MOD land and rubbish off the premises. Note:work is to be executed at any height and situation.

M&L for Digital tiles 600x300x 6to7 mm thick on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over 10 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M&L for vitrified ceramic digital tiles (Superior quality) 10mm thick (Square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed in CM 1:6 as in floors .

M&L Non skid ceramic tiles coloured 7 to 8mm thick (square/rectangular ) area of each tile exc 0.11 sqm but not exc 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to matchover and including 15 mm thick screed in CM 1:6 as in floors. Note:Note: size,shade of tile shall be as approved by GE based on manufacturing company catalogue.

S&F in repair 25mm dia medium weight, stainless steel as in drapery rod complete all as specified and directed.

S&F stainless steel brackets colour and design as approved suitable for curtain rods of 25mm dia complete all as specified and direcdted.

S&F for PVC (SWR) 110mm dia pipes single socketed in any length with rubber ring joints, laid in trenches or in floors all as specified and directed.

S & F PVC (SWR) pipes 75 mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors.

S&F 75mm PVC (SWR) bends any radius

All as per item No. 93.00 but with acess door .

S&F PVC (SWR) bends any radius for 110mm bore complete all as specified and directed.

All as per item No. 95.00 above but with acess door .

S&F 75mm PVC (SWR) branch piece single equal or unequal

S&F for PVC (SWR) vent cowl for 110mm bore pipe complete all as specified and directed.

S&F for PVC (SWR) vent cowl for 75mm bore pipe complete all as specified and directed.

S&F PVC (SWR) junction single, (Single T) equal or un equal for 110mm bore complete all as specified and directed.

S&F PVC(SWR) gully trap 125/110mm setting and jointing in solvent cement

M&L reinforced concrete pipe class NP-2 laid and joined complete with collars 150mm bore of pipe.

S&F Factory made RCC manhole covers grade designation LD 2.5, clear opening of frame 450X900mm ISI marked (IS 12592:2002).

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 30mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

M&L for Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper mbedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping complete all as specified and directed.

Taking down chowkhats or frame with shutter (without taking off shutters from the frames) n.exc 1.50 sqm each removing from the site complete all as specified and directed.

Taking down chowkhats or frame with shutter (without taking off shutters from the frames) exc 1.50 sqm but n. exc 4 sqm each removing from site complete all as specified and directed.

S&F pressed steel frame made out of MS sheet 1.25mm thick of size 125x60mm for doors/windows with one or more rebates with and including necessary fixing lugs, stainless steel hinges, lock strike plate etc including filling of concrete 1:3:6 type C-1 back of chowkhats, with two coats of synthetic enamel paint over one coat of red oxide primer, including fixing of holdfast complete. NOTE:- During Fixing of chowkhat, surface shall be make good in plumb with existing finishes like cement plaster ,similar wall tile,floor tile etc and as per site requirement.

S&F pressed steel frame made out of MS sheet 1.25mm thick of size 165x60mm for doors/windows with one or more rebates with and including necessary fixing lugs, stainless steel hinges, lock strike plate etc including filling of concrete 1:3:6 type C-1 back of chowkhats, with two coats of synthetic enamel paint over one coat of red oxide primer, including fixing of holdfast complete. NOTE:- During Fixing of chowkhat, surface shall be make good in plumb with existing finishes like cement plaster ,similar wall tile,floor tile etc and as per site requirement.

S&F factory made of 2nd class hard wood 35mm thick made glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, size of members of shutters as spfd in SSR Part-1, section 8, clause 8.24(a) complete allas specified and directed.

S&F for 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides particle board core including two coat of synthetic enamal paint over one coat of pink primer all as specified and directed by Engr-in-charge. NOTE :- All screws shall be self tapping chrome plated

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube etc all as specified and as directed.

M&L for Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement,suppling & fixing in the frame at site as per specification & drawing.

S&F solid PVC frame of size 50 mm x 95 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube, with necessary arrangement for fixing of glass for louver type window/ ventilator and additional PVC beading around the frame for fixing of wire mesh, S&F in opening complete all as specified and directed.

M&L for preparing of new wooden surfaces of any description over 10cm in width or girth and applying two coat of synthetic enamel paint,over one coat of pink primer complete all as specified and directed by the Engineer-in-charge

S&F 100mm butt hinges, medium weight, cold rolled mild steel.

S&F 125mm butt hinges, medium weight, cold rolled mild steel.

S&F 125mm Butt hinges, extruded Aluminium alloy with galvanised mild steel hinge pin,anodised and fixed

S&F for Extruded aluminium alloy handles,150mm fabricated type anodized

S&F Aluminium, 150mm anodized, barrel tower bolts extruded section & fixed

S&F 250mm Aluminium alloy, anodised,sliding door bolt with hasp,stapple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast-aluminium alloy and fixed.

S&F 20mm dia, Brass chromium plated tubular towel rail, D type, 60cm long with flanges

S&F stainless steel handles cast type, anodised complete for the 125mm size complete.

S&F 250 mm stainless steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete.

S&F stainless steel cast type barrel tower bolts of size 150mm long (ISI Marked) in repairs complete all as specified and directed .

S&F stainless steel cast type barrel tower bolts of size 100mm long (ISI Marked) in repairs complete all as specified and directed .

S&F 150mm long stainless steel handles cast type handles anodised ISI marked complete all as specified and directed.

S&F 100mm long stainless steel handles cast type handles anodised ISI marked complete all as specified and directed.

S&F 250mm long stainless steel type sliding door bolt with hasp, (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of stainless steel and fixed complete all as specified and directed.

S&F 150mm long stainless steel type sliding door bolt with hasp, (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of stainless steel and fixed complete all as specified and directed.

S&F for door stoper of brass 140mm body and tounge complete all as specified and directed.

Supply and fix kitchen plate rack made out of stainless steel 0.8mm thick complete of size not less than 750x750x200mm, duly assembled and fixed to wall with wall screws / fasterners all as specified and directed.

Taking down cement plaster of any description on brick or stone walls and ceiling including raking out joints, hacking for keys, scubbing down with water etc and complete all specified and as directed.

M&L for rendering 12mm thick on fair faces of brick work or concrete surfaces in CM (1:6) finished even and smooth without using extra cement complete all as specified and directed.

M&L for 10mm thick backing coat in cement mortar (1:4) on vertical surfaces for fixing of tiles complete all as specified and directed.

M&L for rendering cement plaster 5mm thick in CM (1:3) on fair faces of concrete surfaces, finished even and smooth wihout using extra cement on ceilings compleete all specified and as directed.

M&L for preparing of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed by the Engineer-in-charge

M&L for preparing of newly plastered surfaces of ceilling and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed by the Engineer-in-charge

M&L for preparation of newly plastered surfaces and applying two coat of cement base paint over a coat of primer on wall complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying three coats of white wash complete all as specified and directed.

M&L for Preparation of newly plastered or unplastered surfaces on ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparation and complete removal of existing surfaces and applying two coats of oil bound distemper on walls and ceilling, pillars cornices complete all specified and directed.

M&L for preparation and complete removal of existing surfaces and applying two coats of oil bound distemper on ceilling complete all specified and directed.

M&L for 3mm thick wall care putty on wall and Ceiling.

M&L for One coat of synthetic enamel paint on old painted Steel or iron surfaces of any description over 10 cm width or girth including preparation of surface.

M&L for Two coat of white wash on wall/ceiling including preparation of plastered or unplastered surfaces by brooming down or steel wire brushing; scrapping down smoke soot, moulds,moss and efflorescent salts and trading oil and greas spots; removing nails, good holes,cracks etc. by filling with putty.

Demolition of Brick work or stone/boulder masonry, built in CM including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles.

M&L for Brick work with fly ash bricks, straight or curved or plain exc 6m mean radius built in cement mortar 1:6.

M&L for fly ash brick work using old size bricks, straight or curved on plan to any radius, built in CM 1:4 as in half brick thick wall complete all as specified and directed.

Demolition of cement concrete in ground floor and pavings n.exc 15cm thickness (below or above ground level).

M&L for 75mm thick PCC 1:4:8 Type D-2(using 40mm graded aggregate) as in sub base over rammed earth complete all as specified and as directed.

M&L for Chequered cement concrete tiles with grey cement and pigment 30cmx30cmx25mm thick, with rubber moulded glassy finished surface, laid in floors over and including 15mm thick screed bed or beddingin CM 1:6 pointed in neat cement slurry in floors.

M&L for 100 mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base , surface finished even and fair without using extra cement complete.

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in plinth protection, laid in alternate ways, surface finished even and smooth using extra cement complete.

M&L for light shade vitrified tiles flooring 9-10mm thick (square/rectangular), polished, area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed in net slurry and pointed in white or coloured cement to match existing shed complete all as specified and directed.

M&L for Terracotta brick tiles 230x40x20 mm thick on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

S&F of aluminium grills, fixed with ‘F’ channel, DG-104 pattern, 5.50 mm thick and fixed to window complete all as specified and directed.

S&F for factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of lasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge.

S&F for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 50X100mm (Single/double rebated) comprising of virgin PVC polymer of K value 58-60 Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being ermite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge and including M.S. hold fast/ lugs or SS dash fasteners etc.

S&F for steel work as in tabular trusses/supproting pipes etc complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St-240

S&F Prepainted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength 550 mpa as in roof covering/cladding to wall,fixed with self tapping screw complete all as specified and as directed. Gap between wall face and sheet if any shall be sealed using CM 1:3 with WPC.quoted rate deems to be inclusive of the same.

S&F Prepainted Galvalume aluminium zinc coating GI based Plain sheet 0.50 mm thick of any colour having tensile strength 550 mpa as in roof covering/cladding to wall,fixed with self tapping screw complete all as specified and as directed.

S&F for plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment

Supply and fixing position suspended false ceiling system using T-grid suspended ceiling grid system . The size of grid shall be 600x600mm with GI frame work main runner 38x24x3600mm, cross tee25x24x600mm/25x24x1200mm and wall angle 24x24x2540mm( thickness of the materail of 0.30mm). using 9mm thick ceiling panel laminated with PVC film on front face and foil back available in the drop texture as per IS-2095, part-I 1996, fixed in the grid of T-grid suspended ceiling grid system duly susupended by 4mm dia GI bar hanged from the purlins of the roof with butter fly clips complete all as specified and directed by Engr-in-Charg. Make: Geproc, Lafars

Taking down carefully copper/aluminium point wiring complete (light, fan, plug point & power complete alongwith fittings (switches, ceiling roses, tube light fittings, bulk head fitting regulator, sockets main switches, DB removing materials to store & making good of disturb surfaces of wall/floors etc as specified & directed.

M&L for point wiring with 1.5 Sqmm (22/0.30mm) PVC insulated and unsheathed multistranded copper conductor cable, 1100 volts grade, ISI marked, FRLS type drawn through and including PVC concealed conduit (ISI marked) of adequate size and its accessories with sunk cast iron/pressed steel terminal boxes of size 1.2mm thick, with 3mm thick plastic laminated sheet cover of adequate size for one light or one fan point controlled by one switch incl 1.5 Sqmm (nominal area) copper conductor cable (multistrand), FRLS type, PVC insulated and unsheathed with colour code earth wire connected to common earth dolly at one end and metalic bodies of luminaires/ fan at other end complete all as specified and directed for One light point/ fan point controlled by one, one way swtich.

All as per Item No. 166.00 above but One 5 Amp 5 pin socket outlet point on same board with other switches including earth wire as specified.

All as per Item No. 166.00 above but with 2.5 Sqmm (36/0.30mm) PVC copper stranded cable FRLS type for one 15 Amp 6 pin socket outlet point including PVC cable 2.5 Sqmm FRLS type copper stranded conductor as earth wire as specified & connected to commen earth & earth terminals including boards for mounting purposes.

All as per Item No. 166.00 above but on independent board.

All as per Item No. 166.00 above but one light point controlled by 2 way switches.

All as per Item No. 166.00 above but one bell/buzzer point controlled by one push button.

Supply and fix switch piano flush button type 5 Amps single pole one way .

Supply and fixing of switch modular type 6 Amps one way, 1 module, AC 230 Volts, shrouded terminal, ISI marked complete all as specified and directed.

Supply and fixing of modular type socket 6 Amps 3 pin round socket with child safety shutter (ISI marke), AC 230 Volts, shrouded terminals, smooth plug removal and insertion complete all as specified and directed.

Supply and fixing of switch modular type 16 Amps one way, 1 module, AC 230 Volts, LED based indicator, shrouded terminal, ISI marked complete all as specified and directed.

Supply and fixing of Modular 20 Amp, Mini MCB SP C Curve, AC 230 Volts, laser marking, ISI marked complete all as specified and directed.

Supply and fixing of modular type socket 6 Amps/ 16 Amp 3 pin socket with child safety shutter (ISI marke), AC 230 Volts, shrouded terminals, smooth plug removal and insertion complete all as specified and directed.

Supply and fixing of modular type bell push 6 Amps, AC 230 Volts, LED based indicator, shrouded terminal, ISI marked complete all as specified and directed.

Supply and fixing of switch modular type 6 Amps two way, 1 module, AC 230 Volts, LED based indicator, shrouded terminal, ISI marked complete all as specified and directed.

Supply and fixing of modular type fan 8 step regulator, 100 watt, AC 230 Volts, 2 module, laser marking complete all as specified and directed. .

Supply and fixing of ceiling rose surface PVC 50mm dia 3 terminals including PVC mounting block white/ivory finish.

Supply and fixing socket combination 2 in 1, 5 Amp flush type complete all as specified.

Supply and laying or fixing or passing through pipe 1100 volts grade heavy duty cable with PVC insulated stranded aluminium condcutor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and over all PVC sheathed of size 6 Sqmm 2 core complete all as specified and directed.

M&L for Double Walled Corrugated DWC HDPE Pipe of outer dia 40mm and innter dia 32mm including 90 degree bends with coupler and rubber ring laid in trenches of size upto 10 mm suitable for cable protection of cable complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and fixing of 20 Watt LED inverter LED batten with square profile and aluminium batten channel in anodized finish, 6500 K colour tempreture, lithium Ion battery with charging time 8hours-10 hours and back up time upto 4 hours complete with all accessories pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size.

Supply and fixing of LED tube light fitting 10watt, 2 feet, CRCA batten complete with retrofit T8 Polycarbonate tube with connector block, etc. complete with all accessories pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size.

Supply and fixing of LED light fitting, 10 Watt bulkhead light mounted type with metallic channel and white reflector, suitable for mirror fittings with connector block, etc. complete with all accessories pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size.

Supply and fixing of LED street light fitting 30 watt complete with powder coated die cast aluminium compact,IP 65 protection complete with all accessories pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size Note : Adequate size of bracket / clamps, nut, bolts, washers, etc required at site is deem to be included in this item rates.

Supply and fixing of bell ding dong type AC, 230 volts, single phase complete all as specified and directed.

M&L for in replacement of MS box of size 130x100x30 cm depth, dust proof with front opening hinged door both side, made out of 2mm thick MS sheet cubical type with powder coated painting for mounting of MCCB, DB's, electric meter etc inside the box fixed in wall by necessary cutting of wall of suitable size in concealed and making good the surface, by applying cement work, brick work and matching colour (Oil bond distemper) etc including dismantling of MS box with MCCB, DB's and electric meters and refixing the same MCCB, DB's and electric meters in new box carefully including necessary electric connection by suitable size of copper conductor cable of suitable length and testing complete all as specified and directed. Note : (a) Any plastering work involved while taking out old UNSV meter box and refixing the new meter box is deem to be included in this rate. (b) PVC flexible conduit required within the meter boxes is deem to be included in this item rates.

Supply and fixing in replacement of submain wiring with two single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLS type, cables 6 Sqmm drawn through in and including rigid PVCcasing caping including 6 Sqmm 1100Volts grade, FRLS type, PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed.

Supply and fixing in replacement of submain wiring with two single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLS type, cables 10 Sqmm drawn through in and including rigid PVC heavy duty concealed conduits including 10 Sqmm 1100Volts grade, FRLS type, PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed. Note for item srl No 192.00 & 193.00 :- (i) Two runs of cables and one run of continuous earting cable drawn in conduit casing coping will be measured as one length of sub main. (ii) PVC conduit and its accessories is deem to be included in this item rates. (iii) Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall, floors etc.

Supply and fixing of sheet metal enclosure (factory made), TPN Vertical Distribution Boards (MCCB Incomer) IP43 protection Double Door : Plain 4 way, MCCB + 12 modules with 200 Amps rated busbar all as specified and directed.

Supply and fixing of distribution board sheet metal enlosure double door shutter type factory made fixed flush with wall or outside on wall surface suitable for mounting isolators & MCB's 240volts, 100 Amp rated bus bar with front openable cover suitable for SP & N 8 ways all as specified & directed.

Supply and fixing distribution board sheet metal enlosure double door shutter type factory made fixed flush with wall or outside on wall surface suitable for mounting isolators & MCB's 240volts, 200 Amp rated bus bar with front openable cover suitable for SP & N 4 ways all as specified & directed.

Supply and fixing of MCCB 125 Amp TP, 415 volts 16KA.

Supply and Fixing of MCB DP/SPN 6-32 Amps, 230 Volts, 50 Hz with 10 KA .

Supply and fixing of MCB SP 6-32 Amps, 230 Volts, 50 Hz with 10 KA.

M&L for in replacement of Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6.3 mm thickness burried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to and incl galvanised earth lead wire of 4.00mm dia by means of nuts & bolts, check nuts and washers of galvanised incl PCC pit of 1:2:4 type B-1, cover reinforced with XPM weight not less than 4 Kg/Sqm and 6mm dia bar handle, earth pit angle iron frame of size 25mm x 25mm, excavation and earth work in any type of soil, charcoal dust, salt, light grade GI watering pipe 20mm dia with funnel and wire -mesh and medium grade GI protection pipe of 15mm bore from top edge of earth plate upto main distribution board complete all to as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected main switch board all as specified and testing on completion.

M&L for Taking down ceiling fan of any make and size complete all as specified and directed..

M&L for hanging ceiling fan in position and re-commissioning the same including making electric connection complete all as specified and directed.

Supply and fixing Exhaust fan 300mm sweep, Heavy duty, 1400 RPM, AC, 230 volts with louver complete making hole suitable for Exhaust fan 300 mm sweep complete with plastering to disturbed surfaces and making good with plaster and applying distemper paint to matching colour with existing colour complete all as specified and directed.

Supply and Fixing LED luminaires light fittings 1x 20 Watts with decorative box type with driver end cap complete with all accessories such as spring loaded rotor type lamp holder, connector block, LED tube rod etc prewired incl three core copper cable 23/0.0076 from ceiling rose to tube light fittings.

Supply & fixing brushless direct current (BLDC) ceiling fan 1200 mm sweep (ISI Marked), with super enamelled copper wire, white color, Class of insulation "B", 5 Satr rated, ISI marked, rated voltage 230Volt AC, 50 Hz , Rated power 26Watt (+-) 10%, Rated speed 350 RPM (+-) 10%, power factor 0.9 at 5th speed, Air delivery 220 Cum/min (CMM) , service value 8.5 cum/min/W, operating temp 75 degree max, 3 nos aluminium blades and thickness 1.1 mm (after painting), Double ball bearing, speed control through regulator, Low voltage starting i.e. 185 Volt minmum, Insulation resistance more than 2 mega ohm and lekage current 210 MICRO Amps Max includung connection rod as per existing length, writing MES Nos on ceiling fans complete all specified and directed by Engr-in-Charge.

Supply, fixing, testing and commissioning of verticle mounting type electric water heater, storage type, 230volts, AC, 50 Hz, single phase, 5 star rated of capacity 25 ltrs with following specifications:- (i) Rated wattage in watt : 2000 Watt. (ii) Type of water heater : Closed type. (iii) Rated pressure : 0.8 mpa (Class I). (iv) Water head : 80 mtr. (v) Tank warranty : 10 Years. (vi) Outer body material : Engineering thermoplastic. (vii) Safety valve : 4 in 1 multifunctional valve. (viii) Thermostat : Capillery type. (ix) Heating element : Copper tube, Tubular type single pocket. (x) Insulation type : PUF insulation. (xi) Tank material : MS, with glass lined coating. (xii) Cord type/ material : 2.5 Sqmm, 3 core PVC insulation. (xiii) Maximum reheating type : 60 minuites. (xiv) Min. hot water output : 50 degree celcius. minimum. Note : 1. Rate including for grouting of fasteners, nuts and bolts are including in this item rate. 2. Contractor shall furnish original tax invoice with manufacturers warranty 10 years for tank, 02 years for element and 02 years for product.

M&L for Earthing complete with galvanized steel earth plate electrode 60 cm X 60 cm X 6.3 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level connecting to the GI strip 32 x 6mm, by means nut bolt, nuts, check nuts and washer of the GI Earth wire protected by provision of GI light grade pipe 40 mm incl provision of concrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregated with 40 mm thick cover with RCC (1:2:4) reinforced with XPM (weight not less than 4 Kg / Sqm) and frame of angle iron 25mm X 25 mm X 3mm with lugs 2 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, taste point made out of phosphorus bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding than 50 mtr, all as per electric plate No 3 of SSR Part I 2009 and connection to earth test point all as specified incl testing on completion”.

NOTE : - AMOUNT OF SCHEDULE OF CREDIT RS. 24280.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

Alpha Construction (BID ID -3448367)

Abhiraj Enterprises (BID ID -3447578)

MANOVANDANA CONSTRUCTION (BID ID -3445383)