REPAIR REPLACEMENT OF BOUNDARY WALL FENCING GATE AND AREA DRAINAGE ETC FOR 509 ABW SP LINE GWALIOR ROAD KB LINE GE OFFICE ARO MP LINES ETC UNDER AGE B/R-II OF GE(EAST) AGRA

Amount

S&F in repais galvanised ,2 stand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails staining bolts incl, securing or tying at crossing with and provision of galvanised mild steel wire staples or steel pins etc as directed (each line wire to be measured) complete all as specified and directed.

Dismantling fencing wire mesh, chain link any type and any size etc complete all as specified and directed.

Supply only GI chain link fencing any size or any type complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed. Note :- Line wire and flat iron will be measured and paid separately

S &F of Mild steel round bars Fe 290 (Gde - E-165)10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S & F screw bolts (machine made) with hexagonal or sqare heads at one end and screwed the other each screw to be fitted with one washers and one hexagonal or square nut length of bolts n exc 10 cm and dia of shank 16-20mm complete all as specified and directed.

Demolition of cement concrete of any description and any position etc complete all as specified and directed.

M&L providing precast cement concrete 1:2:4 Type B1 (using 20mm graded stone aggregate) for cover slab for manhole, drain and similar articals with plane faces complete all as specified and directed.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu.m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

Dismantling of wrought iron of mild steel work of any description not otherwise providedcomplete all as specified and directed.

S & F angle iron as in post and struts in fencing including embeding in concrete, cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., simillar work confirming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for two coats of synthetic enamel paint over one coat of red oxide primer on new steel Surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint including preperation of surface complete all as specified and directed.

M&L for two coats of synthetic enamel paint over one coat of red oxide primer on new steel surfaces of any description ,over 10cm in width or girth not otherwise described including preperation of surface complete all as specified and directed.

M&L for one coat of synthetic enamel paint on previously treated/ un treated old steel surfaces of any description ,over 10cm in width or girth not otherwise described including preperation of surface complete all as specified and directed.

Demolition of brick work or stone/ boulder Masonry, built in cement mortar including all quoins, pillars etc including removal of spoil etc complete from drain complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L for brick work with subclass B bricks old size straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

-Ditto- all as per item no 18 above but except brick (using old brick)

M&L rendering 15 mm thick in CM 1:4 on fair faces of brick work or concrete surface and finishing surface fair and even complete all as specified and directed.

M&L, rendering 15 mm thick in CM 1:4 on surface other than fair face of brickwork or on one side of lathing and finishing surface fair and even complete all as specified and directed.

M & L for two coat of cement base paint on new plastered surfaces of wall over one coat of alkali resistant primer including preparation of surfaces complete all as specified and directed.

M&L for PCC 1:3:6 Type B2 (using 40mm graded stone aggregate) as in surface channel and drains manhole etc complete all as specified and directed.

M&L for PCC 1:2:4 Type B1 ( using 20 mm graded stone aggregate), in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in eight, copings, kneelers, apex stones bed plates, kerbs chajjas , water troughs, bed blocks and the like including weathering, slightly rounded or chamfered angles and throating, fixing of chain link fencing etcall as directed incl necessary formwork etc complete all as specified and drected

M&L for cement concrete 1:3:6 Type C-2 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

S&F Framed and hung as in doors or gates of angle or other section with gusset plates, rails, braces incl. pintle hinges , stops hand made sliding bolts etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing completeall as specified and directed.

Ditto all as per item No.27 but as on ornamental gate including fixing of pivot at bottom of gate. ( Note :- Weight of gate decided by BOO Convey by Accepting Officer )

M&L for 1.00mm thick mild steel black sheet as in steel gate and similar works cut to size, holes punched including round headed screw welded etc complete as specified and as directed.

S&F Butt hinges, medium weight, cold rolled mild steel, and fixed with screw/ welding (Size of hinges in 100 mm) complete all as specified and directed.

Dismantling floor, hearth wall tiling, granite including cement mortar bedding (but not backing) including rubbish off the premises complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 450x350x7mm thick fixed over and including 10mm thick plaster in CM 1:4 on vertical surfaces such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and drected.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) for in steps, jambs, pillars, window-cills, cooking platforms and like cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M&L Writing Letters of Figures with 1 mm thick stainless steel sheet of grade 304 (Block, Roman, Italic or Indian) not exc. 20cm high over granite stone complete all as specified and as directed.

M&L for preparing old plastered or unplastered surfaces of walls and applying one coat of cement base paint complete all as specified and directed.

S & F steel work as in tubular truss purlin rafter incl. washer incl. necessary cutting welding etc complete all as specified and directed.

S&F in repair of Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Cutting chases for inerting steel sheet and pinning in making good to facing where required and pointing in cement mortor 1:3 to ends or edges on brick wall and cutting not exc 10 cm girth and making good etc complete all as specified and directed.

Cutting holes in brick wall built in cement mortor or cement lime mortor and stone wall built in lime mortor or wall of cement concrete of superficial area n. exc 150 sqcm and making good in cement mortor 1:3 or cement concrete 1:2:4 type B1etc complete all as specified and directed.

C P Singh and Co

Rahul Construction Co

Balaji Associates

N.K. ENTERPRISES

m/s shanti consruction co