Provn of bathrooms and toilets with allied infra for Single JCOs Accn and special repair to Bldg No. TS-100 at ASC, toilet at white knight primary school and lawn tennis court at trikuta under GE Nagrota.

Amount

Schedule 'A' Part-I (B&R and Misc Work)

Taking down chowkats or frames with shutters (without taking off shutters from the frames) n. exc. 1.5 sqm each and removing from site complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground levels), complete all as specified and directed.

Demolition of cement concrete of any description and any position not otherwise specifically provided, complete all as specified and directed by Engr-in-Charge.

Taking down cement plaster on brick or stone wall etc including raking out joints, hacking for key, scrubbing down with water, complete all as specified and directed.

S & F 15mm bore dia Steel water tubes, medium grade, ISI marked, galvanised iron, with all fittings, and fixing complited to wall and ceiling or laid in floor including taking down existing water tubing, complete all as specified and directed.

S & F 20mm bore dia Steel water tubes, medium grade, ISI marked, galvanised iron, with all fittings, and fixing complited to wall and ceiling or laid in floor including taking down existing water tubing, complete all as specified and directed.

S & F factory made solid PVC moulded door shutter 28 to 30 mm thick (stiles) with 2, 4 or 6 raised panel design with 2 mm thick moulded PVC sheet on front face and 2 mm plain colour PVC sheet on back face, complete all as specified and directed.

S & F Solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M S square tube, suppling and fixing in opening as per specification and drawing, complete all as specified and directed.

Box type steel ventilators top hung double shutters (inside for wire mesh out side of glass) including guard bar, hinges, steel handles, tower bolt and steel peg set complete with glazing bar dovetailed or welded including a coat of red oxide after preparation of surfaces before fixing steel windows shall be conforming to relavent IS, complete all as specified and directed.

S & F pressed steel door frame of size 105 mm x 60 mm with one or more rebates using 1.25 mm thick sheet including necessary fixing lugs, lock strike plate including one shop coat of zinc chromate primer, complete all as specified and directed.

Prepration of new or previously untreated steel surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

S & F 150mm long mild steel barrel tower bolt stove enamelled black with bright bolt, complete all as specified and directed.

S & F 150 mm long mild steel pressed handle oval type stove enameled black, complete all as specified and directed.

S & F 100 mm long butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

S & F 3.00 mm thick Sheet glass ordinary quality and glazing with oil putty fixed with bends glazing pins n exc 0.5 Sqm in each pane, complete all as specified and directed.

S & F Galvanised mild steel wire 0.56mm nominal dia of wire and average width of aperture 1.18 mm dia and fixed with tinned tacks or galvanised mild steel staples, complete all as specified and directed.

S & F 300 mm long MS sliding door bolts clamps type stove enameled (ISI marked)black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plates and two on staple plate, complete all as specified and directed.

M&L for 50mm thick PCC, 1:3:6, Type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection finished even and fair, complete all as specified and directed.

M&L for PCC, 1:2:4, type B-0 (12.50mm graded aggregate) as in roof padding finished even and smooth without using extra cement, complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan not exceeding 6m built in cement mortar 1:4 including demolition of existing brick masonary, complete all as specified and directed.

Supply only liquid water proofing materials and using as per mabufacturers instructions, complete all as specified and directed.

S&F 100mm bore dia cast iron waster and vent pipes sand cast in any length with or without ears with cement joints laid in floors or fixed to walls with all fittings including taking down the unserviceable pipe with pipe with fitting, complete all as specified and directed.

S&F 75mm bore dia cast iron waster and vent pipes sand cast in any length with or without ears with cement joints laid in floors or fixed to walls with all fittings including taking down the unserviceable pipe with pipe with fitting, complete all as specified and directed.

M&L for Extra over cast iron pipes and fittings if lead joint is provided in liew of cement joint of 100mm bore, complete all as specified and directed

M&L for Extra over cast iron pipes and fittings if lead joint is provided in liew of cement joint of 75mm bore, complete all as specified and directed

M&L in repairs for 75mm bore dia Cast iron floor trap including jointing to waste pipe fixed in cement concrete, complete all as specified and directed.

S & F 100 mm bore CI bends any radius, complete all as specified and directed.

S & F 75mm bore CI bends any radius, complete all as specified and directed.

S&F CI branch piece single of 100mm bore or with parallel branches, complete all as specified and directed.

S&F CI branch piece double of 100mm bore or with parallel branches, complete all as specified and directed.

S&F CI branch piece single of 75mm bore or with parallel branches, complete all as specified and directed.

S&F CI branch piece double of 75mm bore or with parallel branches, complete all as specified and directed.

M&L for 50mm thick plain cement concrete, 1:2:4, type B-1, (using 20 mm graded crushed stone aggregate) as in sub base of floor surface finished even and fair to receive top layer, complete all as specified and directed.

S&F vitreous china ware urinal half stall any size including all fitting, complete all as specified and directed.

S & F Vitreous china wash basin, white, flat back, size 550X400 mm including waste pipe chain plugs and 32mm dia bore CP coupling including a pair of bracket, complete all as specified and directed.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6, finished even and smooth without using extra cement, complete all as specified and directed.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4, finished even and smooth without using extra cement, complete all as specified and directed.

M & L for 10 mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:3, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for Glazed ceramic coloured tiles 300x 200 x 7 mm thick as in vertical surfaces such as dado,skirting set jointed in neat cement slurry including pointed in white or coloured cement to match over and including 10 mm thick rendering in cement mortar 1:4, complete all as specified and directed.

M & L for Non-skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 sqm but n exc 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or beddding layer in CM 1:4, complete all as specified and directed.

Preperation of new plastered surfaces of wall and applying two coats of white wash, complete all as specified and directed.

Preperation of new plastered surfaces of ceiling and applying two coats of white wash, complete all as specified and directed.

Preparation of new plastered surfaces of wall and applying two coats cement base paint over a coat of primer, complete all as specified and directed.

S & F in repairs 15mm bore dia stop valves, cast copper alloy(ISI marked), screwed down, high pressure, with butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed.

S&F in repairs PVC low level cistern 10 ltrs capacity valve less syphone action type with PVC long bend 32mm dia, complete all as specified and directed.

S&F in repairs viterous china squatting any type pan 'Orrisa pattern' long pan size 580mm x 440mm white with P or S trap, front and Integral foot rests any pattern excluding flushing cistern and flushing pipe, complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan ( Semi-pedestal pattern) , white ( excluding flushing cistern and flush pipe but including fixing) including making connections to trap, and to flush pipe, complete all as specified and directed.

S&F 100 mm size CP grating , complete all as specified and directed.

S & F PVC connection 15mm size with PTMT nuts with length 450mm long, complete all as specified and directed.

S&F in repairs 15mm bore Bib taps, Fancy type, cast copper alloy with crutch or butterfly handle,screwed down,screwed for iron pipe or for brass ferrule, complete all as specified and directed.

S&F in repairs 15mm bore dia angle valve/consealed stop cock of cast copper alloy, chromium plated, fency type, scrwed down high pressure with capstain head screewed both ends, complete all as specified and directed

S&F in repairs 15mm bore dia Bib taps brass, Fancy type, cast copper alloy chromium plated CP Body ( long body ) screwed down ,screwed down for iron pipe or for brass ferrule, complete all as specified and directed.

S&F in repairs 75mm dia cast iron cowls, complete all as spd and directed.

M&L for 50 mm thick PCC, 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) as in padding finishing even and smooth without using extra cement, complete all as specified and directed.

M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm including bitumen primer @ 3.5kg/sqm, complete all as specified and directed.

M&L for APP (atatic polypropline) modified membrane 3mm thick minimum weight not less than 3kg/sqm with 160 gsm/Sqm, non wove polyster mat as center core reinforced laid with 75mm side overlap and 100mm end overlap. The membrane has to be laid with LPG torch and over lap shield and finished neat over roof including a coat of bitumen 85/25 @ 1.2 Kg/Sqm over APP membrane, complete all as specified and directed.

M&L for Cement concrete tiles 20cm x 20cm x 20mm thick, machine pressed, set jointed and pointed in neat cement slurry and roof over and polished with grey cement and no pigment over and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

Preparation of surface by brushing with wire brushes for removing caked mud etc, sweeping with brooming and finally fanning the cleaned surfaces with gunny bags to remove all loose dirt etc including roughining surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc including brushing and applying evenly a priming/tack coat with bituminous primer using paving bitumen VG-10 @ 10Kg/X sqm, complete all as specified and directed.

M&L for 50mm thick premixed bituminious macadam with 4% of binder content by weight of total mix using paving bitumen VG-30 laid rolled and compacted to required gradient and cabmer(consolidated thickness upto maximum 75mm) to make good the cut edges of roads etc, complete all as specified and directed by Engr-in-charge

M&L for PCC, 1:1.5:3, Type A-1, (20mm graded crushed stone aggregate) as in filling and mass concrete surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for PCC, 1:2:4, type B-0 (using 12.5mm graded crushed stone aggregate) as in copings, benching, weatheing and slightly chamfering, complete all as specified and directed.

M&L three layer acrylic liquid based synthetic surface non cushioned as per manufactures instructions and authorised applicator complete including marking of tennis court in two layers of approved anti slip line marking paint ,complete all as specified and directed.

Forming contraction (Dummy) joints 65 mm deep x 10 mm wide filled with sealing compound of grade 'A' complete all as specified and directed.

S & F prepainted galvatume zluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof coveing/cladding to wall fixed with self tapping screws/L-type or J-type or cranked hook bolts in lieu of screw as per manufacturer instruction including dismantling of existing asbestos cement , complete all as specified and directed.

S & F prepainted galvatume zluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof coveing/cladding to wall fixed with self tapping screws/L-type or J-type or cranked hook bolts in lieu of screw as per manufacturer instruction including dismantling of existing asbestos cement , complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm each and n. exc. 4.00 sqm each and removing from site, complete all as specified and directed.

Demolition of brick work or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and directed.

M&L for mild steel framed work as in roof trusses ( framed) , trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing( Beam, tee, angle, channel or flat sections ) including fabrication. , conforming to grade Fe 410-S, complete all as specified and directed.

Floor door stopper of aluminium alloy body and tongue , anodised , with hard drawn steel spring , fixed in floor , over all length of cover plate 140 mm , complete all as specified and directed.

S&F 125 mm long anodised aluminium alloy handles fabricated type , complete all as specified and directed.

S&F 300 mm mild steel oridinary rat tail rod pattern springs including roller and roller plates, complete all as specified and directed.

M&L for hold fast/clamps of mild steel stay for rain water pipes etc. confirm to Fe-290 Gde E-165, complete all as specified and directed

S & F 250 mm long aluminium alloy, anodized sliding door bolt with hasp stapple ( bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and directed.

S & F 150mm aluminium anodised barrel tower bolt of extruded section and fixed, complete all as specified and directed.

Box type steel window side hung double shutters with provision for desert coller/AC (Inside for wire mesh & outside for glass), including guard bar hinges, steel handle, tower bolt and steel peg stay complete with glazaing bar dovetailed for welded including a coat of red oxide after preparation of surface before fixing, complete all as specified and directed.

S & F 35 mm thick second class hard wood factory made plain, framed, panelled shutters (two numbers of panels) with lock rail and panel of 9 mm BWP commercials ply or 12 mm veneered particle board on both faces. The size of rails and size as per IS:1003 (Part-I), Kiln seasoned & chemically pressure treated, complete all as specified and directed.

S & F 35 mm thick second class hard wood factory made glazed and skelton shutters, open rebated and prepared to receive glass, gauge, etc. (without sash bars), edges of framing plain, chamered or rounded, fitted with cut and mitred beads for securing glass, etc. Size of memebers of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) for doors, complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.457 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staple, complete all as specified and directed.

S&F 25mm dia curtain rod aluminium brass polished with ends bulbs rings of required size including bracket, complete all as specified and directed.

M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces of walls in cement mortar 1:4 finished the surface even and smooth without using extra cement including mixing of WPC, complete all as specified and directed. Note :- WPC shall be measured and paid separately.

Prepration of wood or wooden based new or previously untreated surface of any description, over 10 cm width or gridth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over 2 to 3mm thick wall putty on plastered surface preparing to distempering on wall surface, complete all as specified and directed.

Complete removal of existing treatment and applying two coats of oil bound distemper over 2 to 3mm thick wall putty on plastered surface preparing to distempering on wall surface, complete all as specified and directed.

Complete removal of existing treatment of old wall surfaces and applying two coats of cement base paint, complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coats of cement base paint, complete all as specified and directed.

M&L for vitrified ceramic tiles 10 mm thick (square/ rectangular)polished, area of each tiles not exceeding 0.36 sqm,as in patches in floors, set and jointed with cement slurry and pointed with white or coloured cement to match with tiles over and including 15mm thick screed bed in cement mortar 1:4 as in floor, complete all as specified and directed.

M&L for reinforced cement concrete,1:2:4, type B-1 (using 20mm graded aggreagate)as in landing cover slabs, manhole, chullah hoods, chajjas, water troughs, mangers shelves and similar acticles with plan faces set in cement mortor 1:4 , complete all as specified and directed by Engr-in-Charge.

Formwork to faces of concrete walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses etc vertica or to batter for flat rough finished surfaces, complete all as specified and directed.

M&L for providing nubmer plate of size 450x300x20mm and set in CM 1:4 and writing building No. of height 8 to 10 cms with luminous paint through grooves of size 12x12mm (base: black, Grooves: Oranges) , complete all as specified and directed.

GI T Grid system in 600 x 600 mm module which includes providing and fixing wall angle along the perimeter of the room with nylon sleeves and wooden screws at 300 mm centre to center. Suspendeding the main tee of size from the soffit, soffit cleat, rawl plugs and wire rod & leveling spring clip at 1200mm center to center cross tee, interlockined into the pre-cut slots in the main tees at 600 mm centre to center in direction perpendicular to the main tee to make a grid of 600x 1200mm. Finally 600 mm cross tees are interlocked in the pre cut slots in the 1200mm tees at 1200 mm center to center in direction parallel to the main tee. Cross Tees having length more than 600 mm are to be supported independently. 4.5 mm thick E board with square edge of size 595x595 mm shall be placed into the grid size of 600x600mm. Size of grid as specifed by manufactures, complete all as specified and directed.

Surface dressing n.exc 30cm deep and averaging 15cm deep and getting out as in any type of soil, complete all as specified and directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n. exc 25 cm in any type of soil, complete all as specified and directed.

Removal of excavated soil to a distance not exceeding 50m and deposited where directed at a level not exceeding 1.50m from the starting point, complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundation filling and mass concrete complete as specified and directed.

M&L for RCC, 1:2:4 (Nominal Mix), type B-1 (using 20 mm graded crushed stone aggregate) as in beams, cantilevers , bresummers, lintels over 1.5m span, complete all as specified and directed.

M&L for RCC 1:2:4 (Nominal Mix) type B-1 (20mm graded crushed stone aggregate) as in slabs supported on walls, beams and cols in floors, roofs, landings, canopies, deck slabs and in shelves and the like, complete all as specified and directed by Engr-in-Charge.

Form work to sofits of suspended slabs such as roof slabs , floor slabs such as roof slabs, floor slabs, landings and simlar works not exceeding 200m thick, complete all as specified and directed by Engr-in-Charge.

Form work to edge of concrete flat, treads breaks in floors, window cills, roofs etc n exc 20 cm wide and sides RCC/PCC bands in wall, horizontal or slopping and similar work fair finished surfaces of concrete, complete all as specified and directed.

Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed

All as per Srl item No. 1.101 here in above but 6 to 8mm dia

M&L for Brick work with sub class 'B' (old size) bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6, complete all as specified and directed.

M&L for Brick work with sub class 'B' (old size) bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:4, complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6 metre mean radius in half brick thick wall built in cement mortar 1:4 , complete all as specified and directed.

M&L for 5mm thick rendering in cement mortor 1:4 on ceiling, chajjas surfaces (concrete surface) finished even and smooth without using extra cement, complete all as specified and directed.

Preparation of new plastered surfaces and applying three coats of white wash on ceiling, complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying three coats of white wash , complete all as specified and directed.

M&L for 75mm thick plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base, complete all as specified and directed

M&L for sand filling under floor or in foundation including watering and consolidation, complete all as specified and directed.

Hard core of broken bricks of gauge not exceeding 63mm of gauge but n. exc 100mm deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface, complete all as specified and directed.

M&L 75mm thick PCC, 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) as in plinth protection finished the surface even and smooth without using extra cement, complete all as specified and directed. Note: The plinth protection shall be laid in panels and length of the each panel shall not be more that 2.00 m and 6mm joints fillled with 85/25 grade bitumen and sand(1:3) shall be provided.

S&F factory made Box type steel window including gurad bar, hinges, steel handles, tower bolt and steel peg set complete with glazing bar dovetailed or welded including a coat of red oxide after preparation of surfaces before fixing steel windows shall be conforming to relavent IS, complete all as specified and directed.

Cutting holes into or through brick walls built in cement mortar and making good in cement mortar 1:3 of cement concrete 1:2:4 type B1 exc half brick not exc full brick as required, complete all as specified and directed.

M&L for 10 mm thick rendering in cement mortar 1:4 over roof surface finished even and smooth without using extra cement, complete all as specified and directed.

S&F for corner glass shelf (with bracket) of jaguar cat part No ACN-1173 or equivalent in approved make complete all as specified and directed

S&F 200mm long aluminium anodised barrel tower bolts of extruded section, complete all as specified and directed

S&F 150mm anodised aluminium handles cast type, complete all as specified and directed

S & F 300 mm long aluminium sliding door bolts clamps type (ISI marked) with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plates and two on staple plate, complete all as specified and directed.

Anti-termite treatment by treating the soil along with external perimer of building at the rate of 2.25 litres of emulsion per square metre of perimeter wall, complete all as specified and directed.

Anti-termite treatment by treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface, complete all as specifed and directed.

All as per Srl item No. 1.121 here in before but under plinth protection.

Anti-termite treatment by treating back fill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (area of substructure in contact with backfill to be measured) complete.

M&L for 110 mm bore PVC (SWR) rain water pipes single socket fixed to wall with PVC clamp, complete all as specified and directed.

M&L for 110 mm bore PVC (SWR) bend for rain water pipes fixed to wall, complete all as specified and directed.

M&L for non skid ceramic, coloured tiles, 300x 300 x 7 mm thick as in floor etc set and jointed in neat cement slurry including pointed in white or coloured cement to match over and including 20 mm thick screed bed or bedding layer in cement mortar 1:4, complete all as specified and directed.

M&L for Glazed ceramic coloured tiles 350 x 250 x 7 mm thick as in vertical surfaces such as dado,skirting set jointed in neat cement slurry including pointed in white or coloured cement to match over and including 15 mm thick rendering in cement mortar 1:4, complete all as specified and directed.

Vitreous china wash down closet pan (Pedestal pattern) white with ‘S’ trap plastic seat cover white including connection to out going pipe & to flushing pipe, anti syphonage pipe etc,complete all as specified and directed by Engineer-in-charge

S&F vitreous wash basins, china falt back, size 550x400mm including 32mm size waste coupling, 15 x 450mm long PVC connection, 32mm size PVC waste pipe and angle brackets of size 30x30x450mm complete all as specified and directed by Engr-in-Charge.

S&F 15mm bore dia Stop/Angle valve cast copper alloy, fancy type, chromium plated screwed both and for iron pipe or for unioin, complete all as specified and directed by Engr-in-Charge.

S&F 15mm bore Bib taps, Fancy type, cast copper alloy with crutch or butterfly handle,screwed down,screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed by Engr-in-Charge.

S & F 15 mm pillar tap, chromium plated cast copper alloy, fancy type with capstan head, screwed down high pressure with and without levelled hot or cold with long screwed shanks and fly nuts screwed for pipe, complete all as specified and directed.

S & F 100 mm dia CP grating openable including fixing to floor trap with white cement, complete all as specified and directed

S & F 100 mm bore dia cast iron, soil ,waste and vent pipes sand cast in any length with or without ears with cement joints laid in trenches or fixed to walls with all fittings, complete all as specified and directed.

S & F 75 mm bore dia cast iron, soil ,waste and vent pipes sand cast in any length with or without ears with cement joints laid in trenches or fixed to walls with all fittings, complete all as specified and directed.

M&L for 75mm bore dia cast iron floor trap with CI grating including jointing to waste pipe in run lead complete and making good the disturbed surface to match the existing surface, complete all as specified and directed.

S& F 15 mm bore dia steel water tubing, medium grade, glavanished iron with all fittings fixed to walls or ceilling or laid in floors, complete all as specified and directed.

S& F 20 mm bore dia steel water tubing, medium grade, glavanished iron with all fittings fixed to walls or ceilling or laid in floors, complete all as specified and directed.

S&F Cast Iron vent cowl 100mm, complete all as specified and directed

S&F Cast Iron vent cowl 75mm, complete all as specified and directed

M&L (SWR) guly trap 125/110mm setting and jointing with solvent cement, complete all as specified and directed

S & F 1000 Ltrs capacity Rotational moulded polyethlene water storage tanks (cylindrical vertical with closed top)double layered hoisted and fixed in position including ball brass valve 20mm bore & tank nipple, complete all as specified and directed.

Supply and fixing CP Soap Dish Recessed Type (Stainless Steel) of Jaguar Cat No. AHS-1531 or equivalent in approved make, complete all as specified and directed.

S&F 20mm bore stop valves, cast copper alloy,screwed down,high pressure,with crutch or butterfly handle.screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed by Engr-in-Charge.

S&F Brass Cp Tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in manhole foundation, complete all as specified and as directed.

S & F 150 mm dia reinforced concrete pipe, class NP-2 laid and jointed complete with collar, complete all as specified and directed.

M & L for 100mm thick PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in bed to drain pipes incluing packing under and hanching against the sides of pipes after laying and tested of 150 mm bore dia drain pipe, complete all as specified and directed.

Construction of Septic tank for 30 users , excavation in ordinary soil, foundation in PCC 1:2:4, brick work in CM 1:4, RCC slab cover in RCC precast manhole cover having 6mm plate embadded all round/fibre reinforced cover with angle iron frame vent shaft and sluge chamber etc of size 4m x 1.4mx1.4m as shown in drg No TD CE/TD-1202/2003 sheet No 1/2 and 2/2 dt 09.10.2003, complete all as specified and directed.

Construction of Soakage well of size 1.8m dia and 2.6m depth in excavation in any type of soil foundation in PCC 1:3:6 , walls of honey combed and solid brick work in CM 1:4, RCC M-25 cover slab filling with bats as shown in drg No TD CE/TD-1202/2003 sheet No 1/2 and 2/2 dt 09.10.2003, complete all as specified in drg, complete all as specified and directed. Note : Rate quoted shall deemed inclusive of dewatering during construction if met with.

Schedule 'A' Part-II (Internal Electrification)

Taking down carefully unserviceable aluminium point wiring (light, fan, socket bell or power) complete, (fittings such as switches, ceiling rose lamp holder, regulators, sockets, pendants) stacking at site and keeping in safe custody for taking credit, complete all as specified and directed.

M&L Point wiring with PVC insulated unsheathed 1100 volt grade FRLS cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium grade ISI marked not less than 20mm dia ,concealed in wall and surface on ceiling with all conduit fittings & fixing acessories inculding sunken anodised pressed steel terminal box not less than 1.2mm thick covered with 3 mm thick plastic laminated sheet cover of suitable size with brass screws for mounting switches, sockets, regulators with and including 1.5sqmm FRLS multi stranded copper conductor drawing as continuous earth wire connected to main earth and earth dolly complete all as specified for the following:-

One light point controlled by one switch 5 Amp.

One ceiling fan/exhaust fan point controlled by one switch 5Amp

One socket out let 5Amp controlled by one switch on same board.

One socket out let 5 Amp controlled by one switch on independent board.

All as per item No 2.02 here in before but point wiring with 2.5 sqmm FRLS multi stranded copper conductor cable for main circuit and 2.5 sqmm cable as earth continuity conductor for one 15 Amp socket out let controlled by one 15 Amp switch on independat board, complete all as specified and directed

S&F Switch piano flush type 5 Amps single pole one way, complete all as specified and directed.

S&F Switch socket combination 2 in 1 5 pin 5 /15 Amps flush type, complete all as specified and directed.

S&F Ceiling rose 3 terminal complete PVC/polycarbonate isolated body, complete all as specified and directed.

S & F Integrel sleek extruded batten aluminium /CRCA channel fitting with LED 18 watt complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz, Cat part No. BLRB DB 118 ( for batten fitting) & Cat part no. BLRB18W CW LED (for LED 18 watt ) of Bajaj or equivalent in approved make, complete all as specified and directed.

S&F LED light fitting 1x9W bulk head luminaries IP 65 complete with all accessories including LED lamp 9 watt , connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V 50 Hz, complete all as specified and directed.

S&F in repairs sheet metal enclosure distribution board SPN 8 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail, complete all as specified and directed.

S & F MCB DP 63 Amps 10 KA 230 volts "C" series, complete all as specified and directed.

S & F MCB single pole 6 to 32 Amps, 10KA, 230 volts 'C' series, complete all as specified and directed.

Supply and laying or fixing 1100 volts grade cable PVC insulated aluminium conductor un-armoured of 16 Sqmm 2 core flat or circular, served with inner sheathing of pace tape and overall PVC sheathed in service connection suspended by insulated hangers not more than one meter apart including 4 mm dia suspension GI wire including taking down of existing cable , complete all as specified and as directed by Engr-in-Charge.

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh of 22 gauge, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI pit shall be filled with charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) as specified including provision of 15mm dia medium grade GI pipe for earth wire protection and 20 mm dia for watering complete , all excavation and earth work & connecting the earthing to an earthing test point / main switch board as specified and testing on completion, complete all as specified and directed.

Taking down ceiling fan any sweep, removing blades, cleaning the fan completly for dust and dirt and hanging the same back to its original position including connecting the 3 core flexible copper wire to ceiing rose etc after the completion the point wiring including replacement old unservicable fan hook, rubber pad, nut bolts and washers etc, complete all as specified and directed by Engineer in charge.

S&F Switch socket combination 2 in 1, 3 pin, 5 Amp flush type, complete all as specified and directed.

S & F Stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc as required, complete all as specified and directed

S&F Lamp holder PVC/polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

S& F LED bulb 7 watt , complete all as specified and directed.

Sheet metal enclosure distribution board SPN 12 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail, complete all as specified and directed.

Deduction to be made from BOQ for schedule of credit (Sch 'A' Part - III) Amount of Rs. 36587.00 during AOC Note:- Tenderers shall not quote for this Schedule

M/S MANISHA BUILDERS