Construction of Video Conference hall (OSWAN) at Gunupur Tahasil, Gunupur (Civil, EI and PH) for 2025-26

Earth work in excavation of foundation trenches in hard soil including dressing of sides and levelling the bed up to the required depth and depositing the excavated materials away from the work site within 50m initial lead & 1.5m initial lifts with sundries & T&P,Cess required for the work complete as directed by the Engineer in charge.

Supplying and filling in foundation trenches and plinth, ditches with sand well watered and rammed in layers not exceeding 23 cm. in depth with all lead and lift including cost, conveyance, loading, unloading, royalties and EMF,DMF and aditinal charges of all materials, cost of all labour, sundries, T&P,Cess required for the work etc. complete in all respect as per direction by the Engineer in charge.

Back Filling of surplus excavated earth at work site by initial lead of 50.00mtr and initial lift of 1.50mtr including cost of all labour T&P, Cess required for the work etc. complete as directed by Engineer-In-Charge

Providing and laying P.C.C. (1:3:6) in foundation and floors using 4 cm. size black hard crusher broken granite stone metal and screened and washed sharp sand for mortar of approved quality and from approved quarry including hoisting, lowering, laying concrete, ramming, watering and curing etc. complete to required levels laid in layers not exceeding 15 cm. thick in each layer including cost, conveyance, royalties, EMF,DMF and aditinal charges of all materials and cost of all labours, T&P, Cess etc complete as per the direction of the Engineer -in –Charge.

Fly ash brick masonry in cement mortar (1:6) in F&P using bricks of “23cmx11cmx8cm" size having a crushing strength of not less than 75 Kg. Per Sq. Cm. including immersing in water till saturation before use, Including splays cutting, circular molding, chamfering and corbelling and all similar type of operations with all necessary projections watering and curing etc. complete including cost and conveyance royalty and EMF,DMF and aditinal chargesof all materials and labour with T&P, Cess required for the work etc. complete in all respect in all floors as per drawing and Technical specification and as directed by the Engineer-in-Charge.

Fly ash brick masonry in cement mortar (1:6) in Superstructure using clamp burnt bricks of “23cmx11cmx8cm" size having a crushing strength of not less than 75 Kg. Per Sq. Cm. including immersing in water till saturation before use, Including splays cutting, circular molding, chamfering and corbelling and all similar type of operations with all necessary projections watering and curing etc. complete including cost and conveyance royalty and EMF,DMF and aditinal charges of all materials and labour with T&P, Cess required for the work etc. complete in all respect in all floors as per drawing and Technical specification and as directed by the Engineer-in-Charge.

R.C.C. work of M-20 grade having minimum compressive strength in work test of 200 Kg/Cm2 at 28 days using 20 mm and down graded size black hard crusher broken granite stone chips of approved quality and from approved quarry including hoisting lowering and laying concrete and compacting by using vibrators watering, curing for 28 days, centring & shuttering and finishing the exposed surface smooth providing grooves or beads where necessary in all floors including cost, conveyance, royalties and EMF,DMF and aditinal charges of all materials , cost of all labour with cost of all T&P, Cess required for the work etc. complete in all respect but excluding cost and conveyance of M.S. rods or steel & binding wires and labour charges for strengthening, cutting, bending grills and placing in proper position.and cost of all labour with all T&P, Cess required for the work etc. complete as directed by the Engineer- in-Charge. A.Footing

B.Plinth Beam

C.Column

D. Lintel

E.Chajja

F.Roof Beam

G.Roof Slab

Straightening cutting, bending bent up or coiled rods, including cranking, hooking, welding or jointing the M.S. rods or tor confirming to I.S. 432 (Plain) and 1785 (Tor) steel and binding, tying the grills, hoisting, lowering and placing in proper position required for R.C.C. works including cost, conveyance and EMF,DMF and aditinal charges of M.S. rods or tor steel and binding wires of 18 to 20 gauge and cost of all labour with all T&P, Cess required for the work etc. complete as directed by the Engineer- in-Charge.

Providing 16 mm thick C.P. with C.M. (1:6) with screened and washed sharp sand for mortar and finished smooth to the rough surface of walls in all heights after racking out joints including watering and curing, rounding of corners, providing grooves where ever necessary with cost, conveyance, royalties and EMF,DMF and aditinal charges of all materials with cost of all labour, T&P, Cess, and scaffolding required for the work etc. complete in all respect as directed by the Engineer in charge.

Providing 12 mm thick C.P. with C.M. (1:6) with screened and washed sharp sand for mortar and finished smooth to the rough surface of walls in all heights after racking out joints including watering and curing, rounding of corners, providing grooves where ever necessary with cost, conveyance, royalties and EMF,DMF and aditinal charges of all materials with cost of all labour, T&P, Cess, and scaffolding required for the work etc. complete in all respect as directed by the Engineer in charge.

Providing 6 mm thick C.P. with C.M. (1:4) on inside surface of exposed RCC with sand for mortar and finished smooth to RCC work after closed deep chipping & slurry treatment including watering and curing etc complete with cost, conveyance, royalties and EMF,DMF and aditinal charges of all materials with cost of all labour, T&P, Cess, and scaffolding required for the work etc. complete in all respect as directed by the Engineer in charge.

2.5 cm (1") thick D.P.C with CC (1:2:4) using 12mm size c.b.h.g chips approved quality from approved quarry including cost, conveyance and EMF,DMF and aditinal charges of all materials and labour with T&P,Cess required for the work etc. complete in all respect as per drawing and Technical Specification and as directed by the Engineer-in- Charge

Providing, supplying fitting and fixing vetrified Tile in floors of size 600mmx600mm (ivory) of approved make IS: 13755 laid on 20mm thick cement mortar (1:4) filling joints with white cement of approved quality including cost, conveyance, EMF,DMF and aditinal charges and royalties of all materials with all labour and T&P, Cess required for the work etc. complete in all floors as per standard specification and direction of Engineer-in-charge.

Providing, fitting and fixing in daddo of vetrified tile 600 x600 mm of approved make laid on 12 mm thick cement mortar 1:3 (1 cement: 3 course sand) and filling joints with white cement of approved quality including cost, conveyance, EMF, DMF, Addl. Charges, Royality of all materials, labour T&P, Cess etc required for the work all complete as per direction of Engineer-In-Charge (for New work only)

Supplying and fitting,fixing of Un-plasticised poly vinyl Choloride (UPVC) (FENESTA / NCL VEKA LTD) Cashment Door- 60 series duly manufactured using UPVC reinforced profiles of 60 mm x 55 mm x 2.5mm for outer frames,102 mm x 60 mm x 2.25 mm case ment door sash profile and 74 mm x 60 mm x 2.5 mm mullion profile capable of mounting single glazing system,structurally reinforced with hot dip galavanised up to 50 microns of minimum thickness of 2.0 mm prefabricated & welded through fusion welding the door sash shall be fitted with 12 mm thick WPC board of greenply make duly fixed with EPDM weathering seal resistant accessories like clippinglocking system made of aluminium 1 No. per set of sashes and the system is to be installed at the site using anchor fasteners,silicon rubber sealant ,easy glazing / deglazing at site etc. including cost and conveyance of all materials,accessories,labour charges,materials and product conforming to ASTM D 638-14 ,EN-477-95 and other applicable codes and standards.

Supplying and fitting,fixing of Un-plasticised poly vinyl Choloride (UPVC) (FENESTA / NCL VEKA LTD) two Track - Three panel sliding window - 60 series duly manufactured using UPVC reinforced profiles of 108mm x 45 mm x 2.5mm for outer frames and window Sash of 39 mm x 58 mm x 2.5 mm capable of mounting single glazing system,structurally reinforced with hot dip galavanised up to 50 microns of minimum thickness of 1.5 mm prefabricated & welded through fusion welding the window frame shall be fitted with 6 mm thick clear toughned glass of SAINT-GOBIN make duly fixed with EPDM weathering seal resistant and the system is to installed using Reinforced Large Coupler at the site using anchor fasteners,silicon rubber sealant ,easy glazing / deglazing at site etc. including cost and conveyance of all materials,accessories,labour charges,materials and product conforming to ASTM D 638-14 ,EN-477-95 and other applicable codes and standards.

Supplying and fitting,fixing of Un-plasticised poly vinyl Choloride (UPVC) (FENESTA / NCL VEKA LTD)Ventilator / Top Hung -60 series duly manufacured using UPVC reinforced profile of 60 mm x 55 mm x 2.5 mm for outer frames 75 mmx 60 mm x 2.25 mm for casement window sash profile capable of mounting single glazing system , structurally reinforced with hot dip galavanised up to 50 microns of minimum thickness of 1.5 mm prefabricated & welded through fusion welding the widow sash shall be fitted fitted with 6 mm thick clear toughned glass of SAINT-GOBAIN Makke duly fixed with EPDM weathering seal resistant accessories like clipping locking system made of aluminium 1 No. per set of sashes and the system is to be installed at the site using anchor fasteners,silicon rubber sealant ,easy glazing / deglazing at site etc. including cost and conveyance of all materials,accessories,labour charges,materials and product conforming to ASTM D 638-14 ,EN-477-95 and other applicable codes and standards.

Supplying of M.S. Grills bar of approved size, febricatrd to fix GCI sheets on roof of ISI marked standard MS Angles of approved thickness and quality of approved Manufacturers with all required iron and aluminum fittings, including mending to sizes supplying and fixing hinged cleats, sand blocks and fixing of oxidized iron or chromium plated iron aldrops, tower bolts, knobs or rings or handles, hinges, screws and other fittings, etc. complete as per requirement including cost, conveyance and EMF,DMF and aditinal charges of all materials and labour with T&P,Cess required for the work etc. complete in all respect as per drawing and Technical Specification and as directed by the Engineer-in- Charge

Finishing plastered wall surfaces with acrylic putty (water based) of approved make on inside plaster / concrete surface and finishing the surface smooth and even by sand papering to receive paint in walls, at all heights with staging wherever necessary with cost, conveyance,EMF,DMF and aditinal charges of all materials, cost of all labour, all T&P,Cess etc. required for the work complete in all respect as per the direction of the Engineer-in-charge.

Wall Painting two coats with plastic emulsion paint over a coat of water bond cement primer to make an even finished surface in all floors and heights to wall surface of approved make and shade including sand papering, applying putty wherever necessary & cost of scaffolding, staging charges with cost, conveyance, EMF,DMF and aditinal charges of all materials, cost of all labour, T&P, Cess etc. complete as per the direction of the Engineer-in-charge.

Providing and applying to outside walls with two or more coats of Weather coat paint over one coat of primer including scaffolding and cleaning the surface before application of approved colour and manufacture at all elevations including all const & Conveyance of material labour and T&P complete.as per specification, instruction of Engineer-In-Charge

Painting two coats with approved enamel paints of approved colour, shade over a coat of primer over new Iron work including sand papering, polishing the surface, cost, conveyances,EMF,DMF and aditinal charges of all materials and cost of all labour with T&P, Cess etc, complete as per specification & direction of Engineer-in-charge.

2.5 cm (1") thick grading Concrete in proportion (1:2:2) using 6mm size c.b.h.g chips approved quality from approved quarry including cost, conveyance and EMF,DMF and aditinal charges of all materials and labour with T&P,Cess required for the work etc. complete in all respect as per drawing and Technical Specification and as directed by the Engineer-in- Charge

Supplying Fitting and fixing of false ceiling of 12 mm gypsum board including cost, conveyance and EMF,DMF and aditinal charges of all materials and labour with T&P,Cess required for the work etc. complete in all respect as per drawing and Technical Specification and as directed by the Engineer-in- Charge .

Providing and fixing gypsum border around ceiling as per required material including cost, conveyance and EMF,DMF and aditinal charges of all materials and labour with T&P,Cess required for the work etc. complete in all respect as per drawing and Technical Specification and as directed by the Engineer-in- Charge

Providing and fixing gypsum Flower around ceiling as per required material including cost, conveyance and EMF,DMF and aditinal charges of all materials and labour with T&P,Cess required for the work etc. complete in all respect as per drawing and Technical Specification and as directed by the Engineer-in- Charge

Providing supplying fitting and fixing chequred tiles flooring on 12mm thick bed of cement mortar 1:3(1 cement : 3 sand) jointed with neat cement slurry mixed with pigment to match the shades of tiles including fixing tiles to proper slope / level mending to sizes including cost, conveyance, EMF,DMF and aditinal charges and royality of all materials with all labour and T&P, Cess required for the work etc. complete in all floors as per standard specification and direction of Engineer-in-charge.

Plain Cement Concrete of proportion (1:2:4) foundation and floors using 12mm size hard black hand broken granite (C.B) chips of approved quality from approved quarry, free from skin, including hosting, lowering and laying compacting concrete in layers not exceeding 15 cm (6") thick to required level ramming watering curing etc. including cost, conveyance, royalty, DMF, EMF, Addl. Charges of all materials with all labour with T&P required for the work etc. complete including dewatering if required as per drawing and Technical specification and as directed by the Engineer-in-Charge.

Recessed wiring to light point/Fan point/ Exhaust fan point/Call bell point with 1.5sq.mm FR PVC insulated single core multistrand copper conductor of ISI marked with 20mm dia non-metallic PVC flexible conduit with 6Amp ,250V Modular switch legrand( Arteor) /Panasonic (vision) ,Anchor ( Roma) or equievalant reputed make & model ISI marked and ceiling rose ISI marked mounted on Metal box having front Modular cover of suitable size, Metal box with 1.5sq.mm FR PVC insulated single core multistrand copper conductor as earth wire including all accessories and connection (Make of wire-Finolex/L&T/Anchor/Havells/V-Guard) Group-A L.P- 10 F.P- 2

Group-B L.P- 20 F.P- 9

Group-C L.P- 2 F.P- C.B.P-2

Supply and fixing of 3 pin 5/6 Amps plug with 5/6 Amps switch on existing board Modular switches connection (make-Anchor/ Legrand /) ( 5A Exixting)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, etc. as required. ( 5 A Separate)

Supply and fixing of Modular metal box on surface or in recess with suitable size of Modular cover in front including providing and fixing of 6pin 6Amp & 16Amp socket outlet and 16Amp Modular switches (make-Anchor/ Legrand /Roma ( 15 APower plug )

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 02 No.s of 3 Pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required..Modular switches (make-Anchor/ Legrand /Roma) (5A+ 5A switch shocket board)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 01 No.s of 6 pin 15/16A modular socket outlet and 15/16 A modular switch & and 01 no. of 5/6 A modular socket outlet and 5/6 A modular switch , connections etc. as required.Modular switches make-Anchor/ Legrand /Roma) (5+15 A switch shocket board)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 02 No.s of 6 pin 15/16 A modular socket outlet and 5/6 A modular switch, connections etc. as required.Modular switches (make-Anchor/ Legrand /Roma) (15+15 A switch shocket board)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 02 No.s of 3 Pin 5/6 A modular socket outlet and 5/6 A modular switch, and fixing 01 No.s of 6 pin 15/16A modular socket outlet and 15/16 A modular switch connections etc. as required..Modular switches (make-Anchor/ Legrand /Roma) ( 2X5+15A)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 03 No.s of 6 pin 5/6 & and 01 no. of 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. ( 15+3x5 A multi purpose Board)

S/F of suitable size Modular G.l. box for surface or in recess with Modular base & cover in front including providing and fixing of 6pin 15/16Amp modular socket outlet with 20/25AMP SP MCB of (Hager/L&T/Legrand make) connection, painting etc as required.A.C

Supplying and fixing of Modular G.l. box for suitable module on surface or in recess with Modular base & cover and blanking plate ( if required) in front including providing and fixing of 25AMP DOL starter (ROMA/ Crabtree/Havells make) of modular type switch, connection, painting etc as required as per the direction of Engineer-in-Charge.

Recessed submain wiring alongwith earth wire with the following sizes of PVC insulated single core multistrand copper conductor ISI marked conforming to IS-694/1990 in 20mm dia non metallic heavy duty flexible conduit 1.6 mm in surface /recessed PVC conduit as required (make of wire -Finolex/L&T/Anchor/Havells/V-Guard) 1 X 1.5sqmm

2 x 1.5 sq.mm

2 X 1.5sq.mm +1 X 1.5sqmm

2 X 2.5sq.mm +1 X 1.5sqmm

2 X 4sq.mm +1 X 1.5sqmm.

Supply and fixing of following way single pole and neutral, sheet steel, MCB distribution board consumer unit, 240 V on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, hinged front acrylic covr for the MCB knobs detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required ( But with out MCB / RCCB / Isolator) 4 WAY (4 + 12) DOUBLE DOOR, HORIZONTAL TYPE

Supply and fixing of 5Amp to 32A rating 240V "B/C" series MCB suitable for lighting and other loads of the following poles in the exiting MCB DB ISI marked complete with connections testing and commissioning etc. as required.(make-Legrand /L&T/C&S) Single pole (SP)

63 A Triple Pole Neutral (TPN)

S/F.of Special earthing complete with provision of 600x600x3mmthick or (2ft x 2ft) copper plate, 38/40mm dia 3mtr long G.I.pipe , 25x3mm thick Cu.flat charcoal and salt/ chemical powder ,funel,earthpit chamber with masonary work including all accessories and connection as per direction of Engineer-in-charge(

Providing and fixing earth bus of 50mm X 5mm copper strip on surface connection etc as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

S/F of Bakelite angle holder/batten holder of ISI marked conforming to IS-1258/1987 in place of ceiling rose

Supplying and fixing two module steeped type electronic fan regulator with proper modular plate switch box including connections etc. as required.(Make: Legrand(Myrius)/ Anchor(Vision)/ Crabtree(Athena)

Supply, delivery and fixing of Ceiling fan hook box made out of 18 swg GI sheet and containing 10 mm dia round ms bar projecting atleast 150mm on either side & duly bent to accommodate ceiling fan down rod bolt & having earthing arrangement as per direction of Engineer-in-charge.

Providing and fixing extra down rod of 60 cm length G.I. pipe 20 mm dia heavy gauge of Downrod as per direction of Engineer-in-charge.

Supplying and fixing of Modular G.l. box of 18 SWG on surface or in recess with suitable size Modular base & cover module in front including providing and fixing of Modular Bulbul Callbell of ROMA or Equivalent make with connection, painting etc as required.

Supply and fixing of 9Watt LED Lamp (Philips/ Havells/ AnchorBajaj)

S/F of 20W/18W LED batten light of crompton(slim LINEA /Dazzle ray)/ Havells/ Panasonic or Equivalent make.

S/F of 1x24W 5700K cool daywhite light surface / Recess celing LED light made up of pressure die cast housing with secondary optics ,IP66 protection Havells make((ENDURA NEO DL SURFACE/ INTEGRA NEO SURFACE) \ of Havells/Crompton or Equivalent make make including fixing on ceiling with grip and Connection as per direction of Engineer-in-Charge.(ext)

S/F of B.H fitting energy saving,surface mounted decorative round plastic bulk head 1x10Wt LED luminaires comprising high brightness LED with IP54 protection.Havells Make.(ELIPSE ROUND/ ELIPSE OVAL/Rugby) as per direction of Engineer-in-charge.

S/F of 45 W LED street light made up of pressure die cast housing with toughned glassindividual high powered LEDs with secondary optics ,IP66 protection Havells make(ENDURA PEARL PLUS )/Crompton NEXUS+ OR Equivalent make including all accessories and connection as per direction of Engineer-in-Charge.

S/F of 36 Watt 2' X2' LED Square/Round surface mount fitting (Make-Havells/Philips/C&S/Crompton)

Supply & Installation of surface LED Luminarie of Mirror Light (6W) of make JAQUAR/ Equivalent of Philips/bajaj/ Wipro.

S/F.of 48"A.C.Ceiling fans complete with ISI marked (Havells (SS390 metallic/Havells SS390 DeCo) Usha Allure)/ Orient(Jazz/summer pride).Make or Equivalent make including all accessories & connection as per direction of Engineer-in-charge.

S/F of Wall Mounted Fan including all accessories of USHA(Mist Air Icy Blue)/Crompton (Wall Mounted Fan-High Flo LG 18") make & connection as per direction of Engineer-in-charge.

Exhaust fan 9" size

Supply of 1.5 Ton 5 star(BEE rating 2024 rated split Air conditioners of Carrier/Blue Star/LG make.or Equivalent make

Installation and fixing of AC machine

4KVA,15Amp voltage Stabilizer of voltage range 130V to 300V,Digital wall mounted (Model No.VWR 500/VBG 500) of V-guard/Shakti/Luminous make

S/F of MS outdoor stand FOR split Air conditioners

Extra 1/2 '' and 1/4'' suction discharge copper pipe to the outdoor unit of 1.5 Ton split type AC machine

Rate Analysis of S/F of double battery of 150AH with 2KVA Inverter of Make Luminous/Exide/Sfsonic including all accessories and connection as per direction of Engineer-in-charge.

S/F of 10 sq.mm 4 Core Alluminium, armoured LT power Cable of XLPE insulated 650/1100 grade(make-Havells/Polycab)

Supply,installation,testing & commissioning of 65" 4k Smart Tv .Make: Samsung/LG/or equivalent make

Supply of 16 Port Gigabyte LAN Switcher Make- DLINK/ DIGISOL

Supply & laying of 4 pair Cat6 UTP 4P AIR,23AWG,FRPVCCM, Gray,in existing conduitsMake:- Legrand/Systimex as per direction of Engineer-in-charge.

Supply & Fixing of 4U Wall Mount Rack loaded . .Make:CP PLUS/Hikvision or equivalent make

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes conforming to IS:15778, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 20mm dia C - PVC pipe SDR - 11

32mm dia C - PVC pipe SDR - 11

Supplying all materials, labour T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all joiniting materials including cost & conveyance of all materials to worksite, payment of taxes etc. all complete as per P.H specification and direction of the Engineer-in-charge.15mm dia CP angle stop cock (Con-CHR-053KN Jaquar make)

15mm dia CP two in one bib cock (Con-CHR-041KN Jaquar make)

15mm dia CP Pillar cock (Con-CHR-011KN Jaquar make)

32mm dia brass full way valve (Shakti make)

15mm dia CP Health faucet (Con-ALD-MCH-573 Jaquar make)

15mm CP Extension piece

125mm CP grating

15mm size C.P. flange

supplying all materials, labour, T&P and cutting holes through existing brick work including making good the damages in cement mortar (1:4) for taking G.I. Pipes and fittings/ P.V.C. pipes and fittings including watering, curing, cost & conveyance of all materials to worksite, payment of royality, taxes etc. all complete as per direction of Engineer-in-charge.

Supplying all materials , labour, T&P and cutting holes in RCC floors and roofs upto 19cm thick for passing P.V.C pipes and G.I fittings etc. , and repairing the holes after insertion of pipe etc. with cement concrete (1:2:4) including finishing complete so as to make it leak-proof as per P.H. specification and direction of Engineer-in-charge

Supplying all materials, labour, T&P and cutting grooves in pucca floors and walls for taking G.I./P.V.C. pipes and making good the damages including watering , curing , cost & conveyance of all materials to worksite, payment of royality, taxes etc all complete as per direction of the Engineer-in-charge.

Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches , cost & conveyance of all materials to worksite, payment of taxes etc. all complete as per P.H specification and direction of the Engineer-in-charge. 110mm U-PVC SWR Pipe (Ori Plast/Finolex/Supreme Make Type-B)

110mm U-PVC ‘P’ Trap(Ori Plast/Finolex/Supreme Make)

110mm U-PVC door bend(Ori Plast/Finolex/Supreme Make)

110mm U-PVC Plain bend(Ori Plast/Finolex/Supreme Make)

110mm U-PVC offset without ear(Ori Plast/Finolex/Supreme Make)

110mm U-PVC Cowl(Ori Plast/Finolex/Supreme Make)

110mm U-PVC S/Jn door(Ori Plast/Finolex/Supreme Make)

110mm U-PVC Plain tee(Ori Plast/Finolex/Supreme Make)

110mm U-PVC Door tee(Ori Plast/Finolex/Supreme Make)

110mm U-PVC Socket(Ori Plast/Finolex/Supreme Make)

Supplying all materials, labour, T&P and fixing the following vitreous china Wash Down Water Closet(European type W.C. pan)with integral 'p' or 's' trap to the floor with wooden plug and chromium plated pedestal screws including jointing the trap with soil pipe in cement mortar (1:1) fixing plastic seat and cover for wash down water closet with chromium plated brass hinges and rubber buffers including polishing , cost & conveyance of all materials to worksite, payment of royality, taxes etc. all complete as per P.H specification and direction of the Engineer-in-charge. European water closet with 'p' trap plain(Hindware/Parryware/Neycer make)

Supplying all materials, labour T&P and and fixing 12.50 liters/10 liters capacity low level flushing cistern with a pair of cast iron or M.S. brackets complete with fittings such as siphonic arrangements 15mm nominal size brass/pvc ball valve with polythene float CP brass handle,unions and couplings for connection with inlet, outlet and overflow pipes, 32mm dia CP long flush bend, 15mm dia pvc inlet connection pipe including cutting holes and making good the same and connecting the flush bend with cistern and closet and connceting the inlet pipe with suupply main , cost & conveyance of all materials to worksite, payment of taxes etc. all complete as per P.H specification and direction of the Engineer-in-charge10 ltr. Capacity pvc L.L. cistern with 32mm. Dia CP long flush bend ( Slimline-white-Parryware make ) 10 ltr. Capacity pvc L.L. cistern with 32mm. Dia CP long flush bend ( Slimline-white-Parryware make )

Supplying all materials, labour T&P and fixing wash basins with hole for pillar taps with cast iron or M.S.brackets painted white including cutting holes in walls and making good the damages with supply of wooden plugs, screws and cement etc, fixing pedestal for wash basin recessed at the back for the reception of pipes and fittings, fixing PVC waste pipe of 32mm nominal diameter for wash basin including brass check nut complete, fixing pillar taps capstan head screw down high pressure lettered 'Hot' and 'Cold' with long screws, shanks and back nuts of 15mm dia nominal bore, fixing 15mm dia PVC inlet connection pipe and making connection with pillar cocks and supply mains for wash basin, fixing 32mm dia CP brass waste, cost & conveyance of all materials to worksite, payment of taxes etc. all complete as perP.H specification and direction of the Engineer-in-charge. Halfpedestal basin(560x450)Hindware No.91049+91115

Supplying all materials, labour, T&P and fixing standard sized CP towel rail complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge. Towel ring

Supplying all materials, labour, T&P and fixing standard sized glass-shelf with CP brass brackets and guard rail complete fixed to wooden plugs with CP screws as per specification and direction of Engineer in charge.600mmx125mm plate glass shelf with CP/NP guard rails.

Supplying all materials, labour, T&P and fixing mirror of superior glass mounted on 6mm.thick A.C. sheet or ply wood sheet and fixed to wooden plugs with CP screws and washers complete as per specification and direction of Engineer in charge.600mmx450mm size B.E mirror (swivelled type)

Supplying all materials, labour, T&P and fixing CP soap holder complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge. CP soap holder

Supplying all materials , labour, T&P and cutting holes through existing brick or laterite masonry wall for taking U-PVC pipes and fittings including making good the damages etc. all complete as per P.H. specification and direction of Engineer-in-charge

Supplying all materials , labour, T&P and cutting of RCC chajja for taking HCI or U-PVC pipe and fittings including making good the damages etc. all complete as per P.H. specification and direction of Engineer-in-charge

Supplying all materials ,labour ,T&P and constructing Inspection Chamber of inside size 760mmx760mmx460mm with cement concrete (1:3:6) using 40mm size crusher broken hard black granite metal on bed , KB brick work in cement mortar (1:6) in foundation and plinth, moulding and shaping the channel inside and benching with cement concrete (1:2:4) using 12mm size crusher broken hard black granite chips, 12mm thick cement plaster (1:3) with cement punning to inside, cement flush pointing (1:3) to outside, R.C.C cover slab (1:2:4) using 12mm size crusher broken hard black granite chips with R.C.C man hole cover, earth work in excavation in all kinds of soil and refilling the cavity around the chamber including watering,curing,cost of all materials, conveyance of all materials to worksite, payment of royalty,all taxes etc.all complete as per approved drawing, P.H specification and direction of Engineer-in-charge. Inside size 76cmx76cmx46cm with 18” dia RCC MH cover

Supplying all materials ,labour ,T&P and constructing gully trap chamber of inside size 250mmx250mm with 8cm thick RCC precast cover slab in cement concrete (1:2:4) mix using 12mm size crusher broken HG chips, foundation concrete (1:4:8) using 40mm size crusher broken HG metal on bed and around trap, KB brick work in cement mortar (1:6) in foundation and plinth and inside 12mm thick cement plastering (1:3) finished with a floating coat of neat cement including fixing 100mmx100mm size HCI gully trap, 150mmX150mm size CI grating etc.all complete as per drawing, specification and direction of Engineer-in-charge

Supplying all materials, labour, T&P and providing cement concrete ( 1:4:8 ) with 4cm size crusher broken hard granite metal including watering, curing, cost of all materials,conveyance of all materials to work site with payment of royalty, all taxes etc all complete as per P.W.D specification and direction of Engineer-in-charge 2.75 x 0.15

Supplying all materials, labour, T&P and providing cement concrete ( 1:2:4 ) with 12mm size crusher broken hard black granite chips including watering, curing,cost of all materials, conveyance of all materials to work site with payment of royalty, all taxes etc all complete as per P.W.D specification and direction of Engineer-in-charge 2.75 x 0.10

Supplying all materials, labour, T&P and providing and fixing Vitrified tiles in floors, treads or steps and landing on 25mm thick bed of cement mortar (1:1) ( 1 cement : 1 sand ) jointed with neat cement slurry mixed with pigment to match the shades of the tiles including watering, curing,cost of all materials, conveyance of all materials to work site , payment of royalty, all taxes etc all complete as per P.W.D specification and direction of Engineer-in-charge ( Vitrified floor tiles of premium grade having thickness 7mm to 8mm conforming to IS 13755 of size Kajaria/Somany/Johnson tile 60cmx60cm special printed series to be pre-approved by the Engineer-in-charge ) Kajaria/Somany/Johnson tile 60cmx60cm. 1.81 x 1.52

Supplying all materials,labour,T&P and providing 12mm thick cement plaster(1:4) on brick work including watering,curing,cost of all materials, conveyance of all materials to worksite,payment of royalty,all taxes etc.all complete as per PWD specification and direction of the Engineer-in-charge.

Supplying all materials, labour, T&P and providing and fixing porcelain glazed tiles in dado skirting on 12mm thick cement plaster (1:3) jointed with neat cement slurry mixed with pigment to match the shades of the tiles including watering, curing,cost of all materials, conveyance of all materials to work site , payment of royalty, all taxes etc all complete as per P.W.D specification and direction of Engineer-in-charge( Vitrified mat finish wall tiles of premium grade having thickness 6.5mm to 6.7mm conforming to IS 13753 of size Kajaria/Somany/Johnson tile 60cmx30cm special plain / printed series to be pre-approved by the Engineer-in-charge ) Kajaria/Somany/Johnson tile 60cmx30cm. 2 x (1.81 + 1.52) x 2.13

Factory made single leaf Solid WPC (Wood polymer) composite door shutter of 25mm thickcompacted with wood grain finish structural foam panel of 29mm thickness and a density of 650kg/cu.mtr shall be used as core material for fitting the metal fittings such as tower bolts, aldrops, handles etc shall be provided. A structural adhesive compatible with (EPS) foam shall be used for bending the core material, The material and process for manufacturing the door shutters shall conform to RV-TIFAC composites Design Centre's standards and specifications and the door shutters Conforming to relevant I.S.specification. The finish of door shutter will be plain colour white/ Ivory/ Beige/ Light grey/ Mahogany/ Teak wood or any other colour using high quality pigments. Three heavy whight mild steel butt hinges type-I(ISI marked) size 100mm are to be fitted on one side of shutter. of make Rajshri Plastiwood/ Alstone/Aramstrong or euivalant as per direction of Engineer-in-charge. 1 x 0.76 x 2.13

Factory made Solid WPC door frame of size 90mmx45mm fabricated .The door frame consist of four segments which are provided with plug-in-socket arrangement in-situ in the mould. The segments are plugged in and are joined together by means of screw. The WPC frame shall be provided with The material and process for manufacturing the door frames shall conform to Relavent I.S.specification. The finish of door frame will be plain colour white/ Ivory/ Beige/ Light grey/ Golden brown/Mahogany/ Teak wood/sand stone/Champagne/Pastel blue or any other colour using high quality pigments complete in all respect as per specification. of make Rajshri Plastiwood/ Alstone/ Aramstrong or euivalant as per direction of Engineer-in-charge. 1 x 5.02

Ext. S/D Portion Supplying all materials, labour, T&P and laying in trenches (to level or slope) unplasticized P.V.C. pipe conforming to IS 4985/2000 of the following out side dia for class- 3 (0.60mpa ) including jointing with supply of approved solvent cement by non-heat application method/as per manufacture's specification, provoding and laying in trench cement concrete (1:4:8) with 40mm size hard granite metal in the type C-1 standard bedding surrounding or encasing including concrete for bedding and curing etc all complete as per P.H. specification and direction of the Engineer in charge. 100mm dia P.V.C. pipe

Please Enable Macros to View BoQ information