Horticulture strengthening and upgradation work in the park along the National Highway near Avadh University in Ayodhya.

Pathway

Clearing jungle including Leveling, uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. DSR 23 2.31`

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil DSR 2.6.1

Supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth,sides of foundation etc. complete. AOR

Granular Sub-Base with Close Graded Material (Table: 400-1) Construction of granular sud-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401. For Grading- material (By Mix in Place Method). AOR

Proving and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to planth leve: 1:4:8 (1 cement:4 coarse sand (zone-II) derivedfrom natural source : 8 graded stone aggregate 40 mm nominal size derivedd from natural sources) DSR 23 4.1.8

Providing and laying factory made cobble shape paver block 80 mm thick, compressive strength >= M 30 steel mould compressive technolgy. AOR

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). DSR 16.69

Brick work with common burnt clay F.P.S. (non moulded) bricks of class designation 7.5 in foundation and plinth in: cement mortar 1:6 (1 cement : 6 coarse sand). From ground level upto plinth level DSR 23 CH 14 - 6.1.2

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand) DSR 23 13.1.1

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth Complete. DSR 23 13.80

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) DSR 23 13.47.1

Dry stone pitching 22.5 cm thick including supply of stones and preparing surface complete. DSR 23 16.11

Providing and fixing of Sandstone Garden Bench (3 Seater, without armrest & backrest), in rectangular shape sitting platform of size 1500mm (Length) x 400mm (Width) with two legs of size 350mm (height) x 450mm (width) x150mm thickness with sitting height of 450mm, fabricated from natural sandstone, machine cut with smoothened edges, fine dressed finish, suitable for outdoor use in gardens/parks/government premises, bench is to be treated with special epoxy resign for waterproof coating so as to make surface glossy and whether proof, complete in all respects as per direction of Engineer-in-Charge. MR

Boundary Wall

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil DAR 23 2.6.1

Proving and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to planth leve: 1:4:8 (1 cement:4 coarse sand (zone-II) derivedfrom natural source : 8 graded stone aggregate 40 mm nominal size derivedd from natural sources) DSR 23 4.1.8

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. DSR 23 5.33 All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum DSR 23 5.33.1.1

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. DSR 23 5.33 All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum DSR 23 5.33.2

Steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo-mechanically treated bars of grade fe-500D or more. DAR 23 5.22.6

Centering and shuttering including strutting, propping etc. And removal of form for : Foundations, footings, bases of columns, etc. for mass concrete 5.9.1

Centering and shuttering including strutting, propping etc. And removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers 5.9.5

Centering and shuttering including strutting, propping etc. And removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts 5.9.6

Brick work with common burnt clay machine moulded modular bricks of class designation 12.5 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand). From ground level upto plinth level DSR 23 6.28.1

Brick work with common burnt clay machine moulded modular bricks of class designation 12.5 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand). Above plinth level upto floor V level DSR 23 6.28.2

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 10.25.2

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand) 0 DSR 23 13.1.1

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand). DSR 23 13.11

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth Complete. DSR 23 13.80

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) DSR 23 13.47.1

Providing and laying gang saw cut 30 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20 mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge. DSR 23 16.87.1

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work 8.3.2

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work DAR 23 13.61.1

Pond Cleaning

Ecological insitu treatment of kunds through cownomics process for first three month, which will include, colletction and removal of weeds and floating material from surface of water, with the helop of boat, lake divers, JCB machine and transportation to dumping site as directed bye client (Maximum 5 km) this also includes heavy dosing and spraying of cownomics solution for improving quality of water of kunds. SANCTION RATE FROM REJUVINATION OF 8 KUND PAGE- 353

Ecological insitu treatment of Kunds through cownomics process for next nine months, which will include, manually collection and removal of small quantity of weeds and floating material coming on daily basis from surface of water and transportation to dumping site as directed by the client (maximum 5 km), at least twice a week. This includes medium dosing and spraying of cownomics solution for maintaining the quality of water of kunds. SANCTION RATE FROM REJUVINATION OF 8 KUND PAGE- 353

Horticulture

Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy plant in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge. DSR HORTI 2025 5.12

Providing and stacking of Nerium oleander (kaner) of height 45-60 cm. with 3-4 branches in poly bags of size 20 cm as per direction of the officer-in-charge. DSR HORTI 2025 8.49

Providing and stacking of Hamelia patens of height 90-105 cm. bushy in big size HDPE bags as per direction of the officer-in-charge. DSR HORTI 2025 8.33

Providing and stacking of Plumeria alba of height 165-180 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge DSR HORTI 2025 7.70

Providing and stacking of Saraca indica (Sita Ashok) of height 105-120 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. DSR HORTI 2025 7.80

Providing and placing in position at different kunds 240-liter capacity mobile garbage bins SANCTION RATE FROM REJUVINATION OF 8 KUND PAGE- 349

Electrical

Supply loading unloading sifting & fixing of 2.5 mtr long CNC cut decorative (size-200x200x3mm thick) square bollard light with LED light(120-150 watt) & bakelite sheet 3core 1.5 sqmm cable ,MCB, foundation bolt etc . The base plate size shall be 300x300x12mm thick.The bollard light should be soft 360 digree IP 65 reted distribution made out of GI sheet with finishing pure polyster powder coating in a color of Graphite Grey/ Anthrecite Grey/black with coating thickness 60-80 microns of corrossion resistance /weather protected.Rate shall be including the 300x300x800mm RCC foundation. Minimum warranty of color shall be 5 years and light fixture 2 years. Make should be as per UP PWD approved. MR

Supply and laying of aluminium conductor PVC insulated armoured served sheathed 4core 6 sqmm XLPE cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitablesize or as directed by the Engineer-Incharge ,complete in all respect.The armouring of the cable shall be properly connected with the earth conductor by clamps etc.The cable will be connect to existing Electrical Panel.Make-UP PWD Approved SOR-2022/501/g

Supply and making the End termination with brass compression gland with luges for 1.1 grade Alluminium armured conductor cable equivalent 4x6 sqmm/3x10 sqmm DSR 22/9/1/7 with factor *.789*.973

Supply and laying below 750mm of 63mm dia DWC HDPE pipe including digging and backfilling and repairing of any cutting of road cutting as directed by Engineer Incharge.Make as per UP PWD approved . DSR-22 14.16.1(With factor0.789*.973)

Supply and burring of Safe Earthing Electrode T-39 (Hot-Dip Galvanized), Length up to 3000mm, outer pipe 76 mm inner Dia 38 mm terminal Dia 12 mm, outer Gl pipe of 16 SWG and inner Gl Pipe of 12 SWG with hot dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs. Activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square C.I. frame with hinged cover & masonary housing. (from electrode terminal to switch board, cast of 25 X 3 Gl. Strip will be extra) Make: As per approved in U.P. P.W.D., & C.P.R.I. Certified, complete. PWD SI No. 725D SOR-2018/725D

EXTERNAL LIGHTING PANEL-1 Supply and Fixing Following capacity of automatic street light cubical control panel painted with anticorrosive alkali and acid proof paint consisting of time switch Tso 100 series with contactors, HRC fuses, isolating switch metering instrument & intrument box with CTs etc. in case of TPN, complete in all respect. SOR-2018 SI. No. 807 (f) (I) 40 A TPN SOR/2018/807/f

S&F of 6 Amp. to 32 Amp. DP MCB (10 KA) C Curve CAT-B fixed in above incloser SOR/2022/1009