REPAIR/REPLACEMENT OF LT PANEL FEEDER AND MISC EXTERNAL ELECTRICAL WORKS FOR AREA I AND II AT MILITARY STATION TALBEHAT

Amount

Taking down old damaged Cross arms, bracing supports, clamps ad back plates fabricated from structural steel sections including nuts, bolts etc.

Taking down ACSR conductor of any size and type from pole as directed by engr-in-charge.

Taking down old unserviceable GI tubes light grade up to 80&40 mm dia, on place of rusted GI pipe in support of cables.

Prunning of tree branches not less than 1.5 mtr around the LT/HT Over head line which obstructing the maintainance of electric supply as well as illumination in area including repair of damage broken ACSR conductor GI wire and jumpers, testing of line complete all as specified and directed by Engr-in-charge. (Note-Each span minimum 30 mtr)

M&L For Cross arms, bracing supports, clamps ad back plates fabricated from structural steel sections including nuts, bolts, washers welding, bending drilling, cold or hot drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint all as specified and directed by Engineer-In-Charge.

M&L for stay assembly complete with accessories as shown in electrical plate No. 01, dia of stay rod is 20 mm. NOTE:- Earth work and PCC measured and paid seperately under respective items.

M&L for Cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate for foundations of poles, struts & stay assembly etc all as specified and directed.

M&L for Cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate as in couping of poles etc including fair finishing the exposed surface even and smooth with out using extra cement and necessary form work all as specified and directed

Excavation in in trenches not exceeding 1.5 mtrs wide & not exceeding 1.5 mtr in depth in soft or loose soil & getting out complete all as spfd & directed.

Removing excavated materialn not exceeding 50mtr &deposited where direceted at a level not exceeding 1.5mtrabove the ground level.

Returning , filling in spreading, levelling, watering & well Ramming in layers not exc 25cm thick complete all as spfd & directed.

Supply and laying HDPE pipe 50 mm dia suitable for LT cable protection as per ISI recommended complete

M&L for Earthing complete with galvanized steel earth plate electrode 60cm X 60 cm x 6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below ground level earth plate connected with GI earthing strip (32x6mm) as earthing lead for transformer/feeder pillar box etc. by means of bolts, nuts, check nut and washers of galvanized iron all as shown in Electrical plate No.3 of MES SSR part I and testing on completion including necessary excavation and earth work, adequate common slat, charcoal dust and funnel PCC (1:3:6) type C-1 pit with pre-cast RCC (1:2:4) type B-1 cover, 40mm thick reinforced with 6 mm dia bars, MS bar 3 Nos both ways funnel with 20mm dia GI medium grade watering pipe and earthing lead 40mm light grade protection pipe complete all as specified.

M&L in replacement of cable XLPE insulated heavy duty electric cables with Stranded alluminium conductor, 1100 volts grade, passing through trenches/ducts/pipes and climbing on poles/walls including fixing with proper size of alluminium lugs. For the following sizes. NOTE:- 1. Excavation and earth work to be measured and paid separately.

10 Sq mm 2 Core.

10 Sq mm 4 Core.

25 Sq mm 4 Core.

50 Sq mm 3.5 Core.

95 Sq mm 3.5 Core.

120 Sq mm 3.5 Core.

150 Sq mm 3.5Core.

Supply and laying or fixing in replacement GI tubes light grade 40 mm dia, on place of rusted GI pipe in support of cables, on pole/wall/laid in floor/in trenches.

Supply and laying or fixing in replacement GI tubes light grade 80 mm dia, on place of rusted GI pipe in support of cables, on pole/wall/laid in floor/in trenches.

M&L for repair /replacement of damaged LT panel section of front/back/side /top and bottom portion of any size MS sheet with new of required size or thickness and fixing on existing LT panel board including necessary bracing/welding work and drilling works including necessary hinges and two coat of synethetick enamel paint over a coat of red oxide primer complete all as specified and directed.

Supply and fixing framed work as indoors or gates of angle made out of FE 410-W Gde E-250 quality -A or other section with gusset plates, rails, fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

M & L in replacement of uncerviceable Phase reading indicating LED lamp with holder 230 volt, for all 3 phases (RYB).

Supply and fixing in replacement of MCCB 4 pole , 250 amp adjustablethermal and adjustable magnetic type of rating 35 KA on existing LT panel board including dismantling and taking out of old unserviceable MCCB from the LT panel board complete all as specified and directed

Supply and fixing in replacement of MCCB 4 pole , 200 amp adjustable thermal and adjustable magnetic type of rating 35 KA on existing LT panel board including dismantling and taking out of old unserviceable MCCB from the LT panel board complete all as specified and directed

Supply and fixing in replacement of MCCB 4 pole , 160 amp adjustable thermal and adjustable magnetic type of rating 16 KA on existing LT panel board including dismantling and taking out of old unserviceable MCCB from the LT panel board complete all as specified and directed

Supply and fixing in replacement of MCCB 4 pole , 100 amp fixed thermal and fixed magnetic of rating 16 KA on existing LT panel board including dismantling and taking out of old unserviceable MCCB from the LT panel board complete all as specified and directed

Supply and fixing in replacement of MCCB 3 pole , 63 amp rating of 16 KA on existing LT panel board including dismantling and taking out of old unserviceable MCCB from the LT panel board Note: Item Ser.No.26.00 to 31.00 (Make :Legrand/Havells/L&T or equivalent as approved by Engineer-in-Charge)

Supply and fixing in replacement of MS Chequered plate of 5 mm thick or over in thickness in available of Fe - 290 Gde E165 and fixed in substation building including painting with black colour over one coat of red oxide primeover and making provision for lifting the plate from duct complete all as directed.

Supply and fix combined( volt,Amp,frequency) meter

Supply and fixing ACSR conductor (mink, weasel, squirrel, or ferrate) for LT over head lines on poles.

Supply & fixing Pin type porcelain, vitreous, white, brown or green insulator 100mm high and 65 mm dia including one galvanised mild steel spindle, two galvanised iron washers one galvanised iron nut, complete suitable for 1100 grade.

Supply & fixing Shacle type insulator porcelain, vitreous, white, brown or green insulator 100mm high and 115 mm dia including one galvanised mild steel spindle, two galvanised iron washers one galvanised iron nut, complete suitable for 1100 grade.

Note :- Debris obtained from all items should be removed in low lying areas as directed by Engr-in-charge out of MOD Land. (Rates quoted for items are deemed to be included for this, where removal of debris in the items is not considered.)

M/S SHIVA TRADERS (BID ID -3328140)

HARNAM SINGH ANIL SINGH (BID ID -3327469)

M/S JAI BALAJI TRADERS (BID ID -3327803)

VEER SINGH CONSTRUCTION (BID ID -3327910)