Renovation of House No. 2087,2106 and 2247 (Occupied House) (Type XIII) Sector 23 Chandigarh (Total 03 No. houses) (IBM Scheme No. W4/2025/25168)

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : DSR 2.10

All kinds of soil DSR 2.10.1

Pipes, cables etc. exceeding 80 mm dia. DSR 2.10.1.1

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia DSR 2.10.1.2

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: DSR 6.1

Cement mortar 1:4 (1 cement : 4 coarse sand) DSR 6.1.1

12 mm cement plaster of mix : DSR 13.4

1:4 (1 cement: 4 coarse sand) DSR 13.4.1

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : DSR 17.3

W.C. pan with ISI marked white solid plastic seat and lid DSR 17.3.1

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: DSR 17.7

White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps DSR 17.7.3

Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : DSR 17.10

Kitchen sink without drain board DSR 17.10.2

610x460mm bowl depth 200 mm DSR 17.10.2.2

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. DSR 17.28

Flexible Pipe DSR 17.28.2

32 mm dia DSR 17.28.2.1.

40 mm dia DSR 17.28.2.2

Providing and fixing soil, waste and vent pipes : DSR 17.35

100 mm dia

Centrifugal Sand cast iron S&S pipe as per iS : 3989 DSR 17.35.1.2

75 mm dia DSR 17.35.2

Centrifugal Sand cast iron S&S pipe as per iS : 3989 DSR 17.35.2.2

Providing and fixing collar DSR 17.57

100mm dia Sand cast iron S&S as per IS: 3989 DSR 17.57.2.1

75mm dia Sand cast iron S&S as per IS: 3989 DSR 17.57.2.2

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : DSR 17.60

100 mm inlet and 75 mm outlet DSR 17.60.2

Sand cast iron S&S as per IS : 3989 DSR 17.60.2.1

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.: DSR 18.10

15 mm dia. nominal bore DSR 18.10.1

20 mm dia. nominal bore DSR 18.10.2

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. DSR 18.12

20 mm dia. nominal bore DSR 18.12.2

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : DSR 18.18

20 mm dia. nominal bore DSR 18.18.2

Providing and fixing uplasticised PVC connection pipe with brass unions : DSR 18.21

30 cm length DSR 18.21.1

15 mm nominal bore DSR 18.21.1.1

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) DSR 18.46

15 mm nominal bore DSR 18.46.1

20 mm nominal bore DSR 18.46.2

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank DSR 18.48

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : DSR 18.49

15 mm nominal bore DSR 18.49.1

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. DSR 18.52

15 mm nominal bore. DSR 18.52.1

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 DSR 18.53

15 mm nominal bore DSR 18.53.1

Providing and fixing of Extension nippple upto 1-1/2" length DSR 18.53A

Cutting holes up to 30x30 cm in walls including making good the same: DSR 18.76

With common burnt clay F.P.S. (non modular) bricks DSR 18.76.1

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. DSR 18.77

Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc. DSR 18.78

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than .70 kg as per standard design: DSR 19.4

100 x 100 mm size P-type DSR 19.4.1

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR 19.4.1.1

Providing and fixing C.P. brass long body bib cock of approved quality

15 mm nominal bore DSR 18.51.1

Construction of Curb consisting of cement concrete 1:2:4 including cost of C.P. hinged grating and cost of sand bajri etc.

Providing drip seal joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter :

Providing and fixing of C.P. Steel Grating Heavy (With hole without hole) size 4" i/d of approved make

Providing and fixing of CP Brass/SS/ABS overhead shower with swiveling Joint , 125mm dia (min) with C.P Brass/ S.S Shower Arm and flange to the satsifaction of EIC of approved make ESSCO Model No. 536A & 542A or equialent Model of CERA /Kerovit/ Jal

Providing and fixing of C.P. cup heavy duty make of approved make

Prov. & fixing of looking mirror of size 450x600mm made with 5mm thick (minimum) superior quality glass including cost of hard board, PVC beading and C.P. Screw etc. to satisfaction of EIC of approved make

P/F of Gun-Metal Peat Valve

size 15mm i/d

size 20mm i/d DSR 18.17.1A

Providing and fixing of CP Brass/SS Towel Rail 600mm of with screws etc. to the satsifaction of EIC of approved make Jal Model No. 36520 Warna or equialent Model of CERA /Kerovit/ ESSCO

Providing and fixing of CP Brass/SS/ABS Soap Tray made of Plastic including glass bowl of approved make Jal Model No. 36540 or equialent Model of CERA /Kerovit/ ESSCO

Providing and fixing of CP Brass/SS Towel Ring with screws etc. to the satsifaction of EIC of approved make Jal Model No. 36524 Warna or equialent Model of CERA /Kerovit/ ESSCO

Supplying and fixing in position pre-cast RCC/SFRC Cover with frame of quality MD-10 and size 450mm

Conversion for OWC to EWC with 4" C.I. bend, 4" PVC collar 1 No 4" PVC pipe upto 1'-6" long including dismantling of OWC pan and floor and repair of flooring to its original condition complete in all respect with satisfaction of EIC.

Providing and fixing of G.I. tank Nipple for making connection complete in all respect 20mm dia

Dismantling of Old material, not reuseable, including GI / HCI Pipe & Specials, Faucets, Ceramic Fixtures, PVC tanks & allied items and disposal of malba including that of chase from site to a approved dumping site complete.

Please Enable Macros to View BoQ information