SPECIAL REPAIR TO SNCOs MESS (P-142) AT AF STN NARELA UNDER GE AF GURGAON

Amount

Demolition of cement concrete (un-reinforced) of any description & in any position not specifically provided complete including dismantling of floor tiles etc complete all as specified.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site complete all as specified.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition ) of any description in any position not specifically provided complete complete all as specified.

Demolition of brick work or rubbled stone masonry including all quoins arches , pillars etc built in cement mortar and including removal from the site complete all as specified.

Demolition of Stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc.

Demolition of Mud in roofs, any thickness including plastering and leeping, (whether full thickness removed etc including roof tiles complete all as specified and as directed.

M&L for cement concrete (1:2:4) type B-0 (using 12.5 mm graded stone aggregates) 25 mm thick as in sub base of flooring/tiles etc complete all as specified.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregates) as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified.

M&L for screed bed or bedding layer of mortar 15 mm thick in cement mortar (1:4) for bedding of tiles complete all as specified.

M&L 10 mm thick rendering in cement mortar (1:3) on vertical surfaces for backing of tiles etc complete all as specified.

M&L for Non - skid (joint free) coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

M&L for Glazed ceramic coloured tiles in vertical surface 600X300X 6-7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified.

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade of granite complete all as specified.

M&L of holes in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors ® complete all as specified.

M&L for 50 mm thick PCC (1:2:4) type B-0 (Using 12.50mm graded stone aggregate) as in roof padding complete all as specified & as directed.

M&L for 15 mm thick plaster in cement mortar (1:4) mixed with water proofing compound on roof slabs finished even and smooth (without using extra cement) after cleaning of roof surfaces with wire brushes complete all as specified. Notes : WPC shall be measured and paid seperately.

M&L for water proofing treatment with minimum 3mm thick APP (Atactic Polypropylene) modified polymeric prefabricated five layer membrane over roof consisting of cleaning of concrete or plaster surface of roof & parapet walls and applying evenly a bitumen primer confirming to IS 3488 @ 0.40 Kg per sqm laid using buten torch and sealing all joints of APP modified polymeric water proofing membrane minimum weight 3.6 kg/sqm reinforced with non woven polyester fabric (weight not less than 160 grams per sqm) unrolled and bonded to substrata with logitudinal and end laps 100 mm and 150 mm respectively as per manufacturer's instructions including aluminium paint on top surface complete all as specified.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified.

M&L for providing plain cement concrete (1:2:4) type B0 (using 12.5 mm graded crushed stone aggregate) as in coping or roof kerbs on roof chamfered on edge including trowelling slightly complete all as specified.

M&L for Cement concrete tiles 25cm x 25cm x 22 mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished, set with grey cement and pigments over 15mm thick cement screed bed in cement mortar 1:4 complete all as specified and directed.

Removing bldgs demolished materials / debries exc. 1.50 km but n exc. 5 km and depositing where directed.

M&L for brick work with sub class 'B' old size brick, straight or curved on plan exc 6.0 mtr mean radius built in cement mortar 1:6 etc complete all as specified.

M&L for half brick work with sub class 'B' old size brick, straight or curved on plan exc 6.0 mtr mean radius built in cement mortar 1:4 etc complete all as specified.

M&L for providing reinforced cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

M&L for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified.

Formwork to soffits of suspended slabs such as roof slabs, floorslabs, landings and similar work not exceeding 200 mm thick rough finished in flat surface complete all as specified.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon tal or sloping and similar work exc 5 cm but n exc 10 cm wide rough finished complete all as specified.

M&L for rendering 15 mm thick in cement mortar (1:6) on brick work or concrete surfaces finished even and smooth (without using extra cement) complete all as specified.

M&L for 15 mm thick plastering in two layers (10+5) mm in cement mortar (1:4) on brick or concrete surfaces including rendering on fins, fascias, chajja, parapets etc and finishing the surfaces even and fair (without using extra cement), top layer shall be with WPC as per manufacturer's instruction and complete all as specified. Note: WPC shall be measured and paid separately.

M&L rendering 10mm thick in cement mortar (1:3) as in ceilings finished even and smooth (without using extra cement) complete all as specified.

M&L for Rough Cast plaster on brick walls consisting under coat of cement and sand mortar 1:3 not less than 10 mm thick and while it is in plastic state the Rough cast mixture consisting of crushed stone or fine gravel mixed of size 6 mm with coarse sand and cement in the ratio1:1:1 shall be applied and finish even including necessary grooving complete all as specified and directed.

Supply only intergral water proofing compound ISI Marked complete all as specified.

M&L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over one coat of primer complete all as specified.

M&L for preparation of newly plastered surface of ceiling and applying two coats of oil bound distemper over one coat of primer complete all as specified

M&L for preparation of newly plastered surface of wall and applying Two coats of wheather proofing exterior acrylic emulsion paint over a coat of primer premium quality complete all as specified

M&L for preparation of plastered or unplastered old decorated surfaces by complete removal of existing treatment by scrapping with Trucare Wall Sander : L-01/H-01 (having mechanical vaccum mechanism) having RPM not less than 1500, sand pad of 80 grit having dia of 7"/9" to make the surface free from dust, loose paint etc or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible , filling of holes and cracks with with suitable material like cement or plaster of paris etc and thereafter applying two coat of oil bound distemper over a coat of primer on walls complete all as specified and as directed. Note : (a) Each stage of complete removal of existing treatment and preparation of surfaces after applying putty shall be got approved from Engg-In-Charge in stage passing register before applying the finishes coat. (b) Material shall be procured from manufacturer and work shall be got executed through authorised applicators of manufacturer. (c) Wall care putty shall be measured and paid seperately.

All as per item No.36 here-in-before but on surfaces of ceiling.

M&L for preparation(complete removal of existing treatment) of old decorated external wall/ceiling surface of existing treatment by scrapping with Trucare Wall Sander : L-01/H-01 (having mechanical vaccum mechanism) having RPM not less than 1500, sand pad of 80 grit having dia of 7"/9" to make the surface free from dust, loose paint etc or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and applying Two coats of wheather proofing exterior acrylic emulsion paint over a coat of primer premium quality on wall/ceiling surface including applying 1-2mm thick wall care putty over disturbed surface during preparation of any reason, sand papering thus make surface smooth upto 4th storey buildings complete all as specified and as directed. Note : (a) Each stage of complete removal of existing treatment and preparation of surfaces after applying putty shall be got approved from Engg-In-Charge in stage passing register before applying the finishes coat. (b) Material shall be procured from manufacturer and work shall be got executed through authorised applicators of manufacturer.

Dismantling wall/ceiling board (fiber, pulp insulation) or insulation board/slabs etc including grid work/wooden or aluminium frame works, cover fillet etc Complete all as specified.

M&L for clip in type armed strong metallic powder coated 0.5mm thick ceiling with GI framework made of standard Tee , Angle or any other section as in grid type ceiling framework as approved by GE . Ceiling shall be hanged to roof trusses / purlin rafters with the help of GI wire not less than 4mm dia at an interval n. exc 1m , the size of the metallic powder coated ceiling tiles 600 mm x 600 mm complete all as specified.

S&F for solid colour wood grain printed PVC sheets 5mm thick as in wall panelling inclusive of solvent cement incl necesssary PVC frame work for fixing on brick or concrete wall as per specification and drawing.

M&L for guniting work to RCC work in column, flooring, side walls, beam, slab, etc by removing loose concrete cover etc, cleaning of surface with wire brush and applying epoxy paint to rusted reinforcement and S&F welded wire mesh fabric or wire net less than 95 X 95X 3 mm adhesive, plaster grade for concrete admixture 1 part of cement and 3.5 part of sand and average thickness 40 mm and making the surface even including 15mm thick plastering in cement mortar (1:4) on brick or concrete surfaces including finishing the surfaces even and smooth, without using extra cement plumb and making surface true to geometry in line and including necessary form work to be carried at upto double storey building Note.- Where ever reinforcement required will be measured and paid seperatly etc complete all as specified.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 sqm each complete all as specified and directed.

All as per item No.43 here-in-before but exc 1.5 Sqm and not exc 4 Sqm each complete all as specified.

S&F for Pressed steel frames 125X60mm (made out of 1.25mm thick MS Sheet) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete as specified.

S&F for Pressed steel frames 105X60mm (made out of 1.25mm thick MS Sheet) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete as specified.

S&F factory made 35mm thick flush shutters , solid core construction with block board core and plywood face pannel commercial type on both faces complete all as specified.

S&F factory made 35mm thick 2nd class hardwood glazed and skelton door shutters, open rebated and prepared to receive glass, gauze, (without sash bars) edges for framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-1 section 8 clause 8.24 (a) fitted to chowkats complete all as specified.

S&F solid PVC door frame of size 50mm X47mm made out of 5mm single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with MS square tube supplying and fixing in opening as per specification and drawing.

S&F factory made PVC shelter panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded both side Prelam PVC sheet used instead of Plain colour PVC sheet. Stile and rails feathered at edges PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of prelam PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable prelam PVC sheet beading and joined together with solvent cement , supplying and fixing in the frame at site as per specification & drawing as specified.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple including necessary beading complete all as specified.

S&F in repair Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple including necessary beading complete all as specified.

S&F 100 mm Butt hinges, Stainless steel and fixed complete all as specified and as directed.

S&F 200mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified.

S&F 150 mm size extruded aluminium alloy handles fabricated type anodised and fixed.

S&F 250 mm long aluminium alloy anodised sliding door bolts with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast sections or cast aluminium alloy complete all as specified and as directed.

S&F in repair 200mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified.

S&F in repair 150 mm size extruded aluminium alloy handles fabricated type anodised and fixed.

S&F in repair 250 mm long aluminium alloy anodised sliding door bolts with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast sections or cast aluminium alloy complete all as specified and as directed.

S&F window or ventilators section of frame 72x55mm fixed to wall or concrete surface with rowl plugs made of galvanised steel powder coated and section of shutter 47x20mm mulion section 72x50mm (Based steel as per IS 513 "D" quality galanised as per IS 277 with zinc of 120 gms/sqm) glazed or gauged and wire gauge shutter prepare to receive wire mesh to the shutter (Double door shutter) with total coated thickness of 0.6mm including grills/guard bars made of square bars powder coated fixed to window frame with screws including necessary fittings and all builders hardware such as handles, tower bolts and stays etc complete all as specified and as directed. Make : NCL type-4000 Series (Note : Glass and wiremesh shall be measured and paid separately under respective items)

Hacking out old broken glass (any thickness, size, quality or escription) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F sheet glass 4 mm thick ordinary quality and glazing with oil putty or wooden beads complete all as specified.

Dismantling boarding of any description , fixed in any position with nails complete all as specified and as directed.

M&L PVC 18 mm thick decorative lamination board of density 600kg/cum manufactured by an ISO:9001-2005 certified with termite proof, water proof & flame retardant PVC Sheet. complete fixed with each other using solvent cement adhesive and stainless steel screws etc. panels shall be fabricated using adhesive and screws and all the edges shall be covered with bonding tape and finished as per make and specification and drawing complete all as specified and directed

Supply & Fixing of stainless steel decorative handles 150 mm size for cupboard shutters complete.

Supply & Fixing of stainless steel tower bolt 150 mm size for cupboard shutters complete.

S&F rolled mild steel in framed work as in doors or steel gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing conforming to Fe- 290.Gde-E-165 complete all as specified.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with selftapping screws as specified & directed.

Dismantling of existing water tanks of steel/PVC/AC of capacity exceeding 500 liters but not exceeding 1000 litres complete all as specified.

S&F for rotational moulded polyethylene water storage tanks 1000 ltrs capacity (cylinderical vertical with closed top) hoisted and fixed in position all as per SSR Part I complete all as specified.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified.

Cutting chases, pinning in. making good to facings where required andpointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick wall etc complete all as specified.

S&F medium grade galvanized steel tubing with all fittings & fixed complete to walls & ceiling or laid in floors 15 mm dia bore pipe (including in short length) complete all as specified.

S&F tubes medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors 20 mm dia bore pipe (including in short length) complete all as specified.

S&F in repair 20 mm dia Gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified.

S&F as in repair vitreous china squatting pan, white, orissa pattern, size 580x440mm with integral foot rests (excluding flushing cistern & flush pipe) with cast iron ‘P’ trap incl lime concrete bedding and making good to the disturbed surface to match with the existing surface of floor complete all as specified.

S&F in repair white vitreous China wash down water closet pan (pedestal pattern), and trap (excluding fixing bolts, flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe, etc. complete all as specified.

S&F in repair vitreous china pedestal pattern wash hand basin (flat back) white of size 550x400mm including one number chromium plated waste fittings, 32 mm dia, brass with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed including cutting for and pinning in ends of brackets complete all as specified.

S&F 32 mm dia brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified.

S&F in repairs PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action type with inlet ball valve and float, handle with & including bracket and PVC flush pipe 32 mm bore complete all as specified.

S&F in repair vitreous China urinals, half stall type , complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe including one number chromium plated waste fittings, 32 mm dia. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

S&F urinal spreader of chromium plated for fixing with 15 mm dia pipe complete.

S&F in repair vitreous china urinal partition white of size 310x700 mm terminating about 40cm above floor line complete as specified.

S&F Soap dish of chromium plated or stainless steel fixed to wall with chromium plated brass screws.

S&F in repair PVC connection 450 mm long suitable for 15 mm GI pipe with two brass nuts & rubber washers complete all as specified.

S&F brass CP mixer for mixing hot & cold water with bend pipe for overhead shower screwed down for iron pipe 15 mm dia and fixed complete all as specified.

S&F in repair 15 mm dia stop valve/angle valve, cast copper alloy screwed down high pressure, fancy type chromium plated screwed both ends for iron pipe or unions complete all as specified.

S&F in repair bib taps long body, brass, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket with water saving aerator complete all as specified.

S&F in repair chromium plated shower roses 125 mm size with or without swivel joints of standard size including fixing to 15mm steel pipe or union complete all as specified.

S&F in repair Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified.

S&F in repair pillar taps , cast copper alloy, with capstan heads, fancy type chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for 15mm bore iron pipe and fixed complete all as specified.

S&F in repair 100 mm chromium plated grating complete all as specified.

S&F in repair 110 mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to walls complete all as specified.

S&F in repair 110 mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints laid in trenches or floor complete all as specified.

S&F in repair 75 mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to walls complete all as specified.

S&F in repair 75 mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints laid in trenches or floor complete all as specified.

S&F 75 mm dia PVC (SWR) vent cowl complete all as specified.

S&F 110 mm dia PVC (SWR) vent cowl complete all as specified.

S&F in repair 110 mm dia PVC (SWR) bends with rubber rings joints fixed as required complete all as specified.

S&F in repair 75 mm dia PVC (SWR) bends with rubber rings joints fixed as required complete all as specified.

S&F in repair 110 mm dia PVC (SWR) junction single, (Single T) equal or unequal with rubber rings joints fixed as required complete all as specified.

S&F in repair 75 mm dia PVC (SWR) junction single, (Single T) equal or unequal with rubber rings joints fixed as required complete all as specified.

S&F in repair 50 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints including bend, tee, laid in trenches/ floors/walls complete.

S&F in repair Salt-glazed stoneware gully traps (150X150) mm, square or round mouthed, type 'P' complete all as specified.

M&L PVC (SWR) 75 mm floor trap plain with grating including jointing with solvent cement complete all as specified.

S&F PVC (SWR) 'P’ trap 125 mm complete all as specified.

S&F 110mm PVC (SWR) WC connector bent type complete.

S&F 25 mm outer dia medium weight pipe made out of stainless steel 304 grade, including decorative ornamental knobs at both ends and one set of ornamental decorative Stainless steel clamps to fixed to walls complete all as specified.

S&F 15 mm outer dia stainless steel rode 1mm thick, with bracket for ward robe including full threaded steel screws complete.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and mixed in position complete in all respect as specified.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified.

M&L preparation of new or previously untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

M&L prepration of new Steel surfaces of any description, not otherwise described, over 10cm width or girth & applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified

M&L for preparation of old painted surfaces of wood and wood based material of any description over 10cm width or girth by cleaning, sand papering,brushing etc , filling in cavities and cracks etc with approved filler and applying one coat of synthetic enamel paint to give an even and smooth surface having no sign of brush marks complete all as specified .

S&F in repair 300mm, ordinary rat tail made of brass rod pattern springs including roller and roller plate complete

M&L 100 mm thick PCC 1:4:8 tybe D-2 using 40mm stone aggregate as in subbase.Complete all as specified

M&L for screed bed or bedding layer of mortar 20 mm thick in cement mortar (1:4) for bedding of tiles complete all as specified.

M&L for 22-25 mm thick chequered designer coloured tiles (matt/glass finish), size, colour and shape as approved by GE, set and jointed in neat cement slurry and pointed with coloured cement to match etc complete all as specified as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/loose soil complete all as specified.

M&L for plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete, sub base complete all as specified.

M&L for providing reinforced cement concrete (nominal mix) type B1 1:2:4 (20 mm graded stone aggregates) as in foundations including rafts, column footings, plinth beams, etc complete all as specified and as directed

M&L for providing reinforced cement concrete (nominal mix) type B1 1:2:4 (20 mm graded stone aggregates) as in columns, pillars, piers, posts and struts etc complete all as specified and as directed

M&L for mild steel TMT bars 5 mm dia and over, upto and including 10 mm dia as in stirrups, cut to length, bent to shape required including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and as directed

Form work to sides of concrete foundations, footing, bases of columns, raft beams, sides and soffits of plinth beams and similiar works etc complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, for square, rectangular or polygonal, rough finished surfaces of concrete etc complete all as specified and as directed.

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admix ture of pigment to match with shade of granite complete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soft/loose soil etc complete all as specified.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified.

E/M SCHEDULE

Taking down carefully copper/aluminium point wiring (light, Fan, Socket or power) fitting such as switches, ceiling roses, pendents, regulators, sockets etc complete removing material to store for keeping in safe custody for reuse or taking in schedule of credit and making good disturbed surfaces of walls, floors etc all as specified as directed.

Dismantling and taking down fluorescent tube light single/double of any wattage or Size street light fittings for repair or replacement of burnt/worn out accessories or carrying to MES store for reuse or taking in schedule of credit.

Taking down unserviceable sub main wiring of any type/Size including wires, conduits,bends,tees/battens etc complete all as specified and directed by Engr-in-Charge.

Taking down unserviceable MCB, MCCB DB's/AC's box with MCB/MCCB to deposit in store for keeping in safe custody for reuse or taking in schedule of credit of any Size/rating complete all as specified and directed by Engr-in-charge.

M&L for point wiring with two runs of FRLS PVC insulated unsheathed, 1100 V grade cable multi stranded copper conductor of Size 1.5 sqmm drawn through in and including concealed PVC conduit Size of not less than 20mm concecled in wall / surface including provn of pressed steel terminal box of suitable Size with 3mm thick plastic laminated sheet cover / modular white cover plate with frame as required module & modular metal flush box as required module for mounting switch, socket and fan regulator along with earth wire of PVC insulated, unseathed, 1100 V grade cable multi stranded copper conductor of Size 1.5 sqmm and making good, disturb surface as it is, all as specified and directed for the following. Note :- Colour coding of cable should be Phase- Red, Neutral- Black and Earth- Green

One light point controlled by one,one way switch.

One ceiling fan/exhaust fan/Air ciculator /bell point controlled by one way switch.

Socket 3 pin 5 Amps on the same board, complete all as specified.

Socket 3 pin 5 Amps on independent board , complete all as specified and directed.

M&L for point wiring with two runs of FRLS PVC insulated unsheathed, 1100 V grade cable multi stranded copper conductor of Size 2.5 sqmm drawn through in and including concealed PVC conduit Size of not less than 20mm concecled in wall / surface including provn of pressed steel terminal box of suitable Size with 3mm thick plastic laminated sheet cover / modular white cover plate with frame as required module & modular metal flush box as required module for mounting switch, socket and fan regulator along with earth wire of PVC insulated, unseathed, 1100 V grade cable multi stranded copper conductor of Size 2.5 sqmm and making good, disturb surface as it is, all as specified and directed for the following. Note :- Colour coding of cable should be Phase- Red, Neutral- Black and Earth- Green

M&L in replacement for sub main wiring with two single core 2.5sqmm stranded copper conductor PVC insulated and unsheathed cable ISI- marked in 25 mm dia, medium grade, PVC conduit concealed in wall for sub main connection including 2.5 Sqmm PVC insulated unsheathed copper conductor ISI- marked as earth wire complete all as specified and directed by Engr-in-charge.

All as per item No 11 herein befoe but submain wiring with 2x4Sqmm and 1x4 Sqmm as earth wire Complete all as specefied and directed.

All as per item No 11 herein befoe but submain wiring with 2x10Sqmm and 1x10 Sqmm as earth wire Complete all as specefied and directed.

S&F for socket outlet 5 Amps, 5 pin flush type, 240 volts. with polycarbonate body. complete all as specified and directed..

S&F for socket out let, 6 pin 5/15 Amps multi purpose 2 in 1 flush type, 230 volts with polycarbonate body.complete all as specified and directed.

S&F for switch piano flush type single pole one way 5 Amps 240 volts with polycarbonate body complete all as specified and directed..

M&L for switch piano flush type single pole two way 15 Amps 240 volts with polycarbonate body complete all as specified and directed..

S&F For ceiling fan regulator stepped electronic type 300 watt rating, 230 volts with polycarbonate body all as directed.

M&L for ceiling rose 3phase/PVC polycarbonate isolated body complete all as specified and directed

Supply & fix Single Pole & netural enclosure with a two pin and earth Plug and Socket 240 volt complete with one single Pole MCB of Cap 20 Amps complete all as specified and directed

Supply and fix in replacement electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc Complete.

S&F in replaceent of MCB DB sheet enclosure load line SPN 240V with 200 Amp suitable Size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated Acrylic double door complete confirming to IP 43 with enclosure blank plates for unused way suitable for 12 way complete all as specified and directed :

S/Fix MCCB DB TPN 4 Way vertical tupe factory made IP 43 protection class metal double door with Shrouded Neutral Bar & Pan assembly with connecting link complete including provision for one MCCB upto 160A after dismantling old one.

S&F MCCB 160 Amp 16 Ka for fixing in DB all as directed by Engr-in-Charge.

Supply and fixing in replacement ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with BEE star rated with brushless direct current motor complete.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz,RPM 1200, Copper winding of sweep 300mm complete as directed.

Supply and fix exhaust fan made of steel body complete with louvers shutter, voltage 230V, 50 Hz,RPM 1200, Copper winding of sweep 300mm complete as directed.

Supply and fixing LED building light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection and L shape GI pipe bracket of 40 mm dia. complete.

Supply and fix in replacement electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE rated complete with all accessories such as safety valve, thermostate, NRV, connection pipe 2 piece etc. complete.

S&F MCBs 240/415 Volts 10 KA finger proof terminal, bi-connect termination, label holder, 35 mm² terminal capacity, insulated sliding shutter, large two position dolly, ISI marked to be fixed on DB . (DB will be measured and paid separately under respective items of sch A):-

(a) MCB C curve SPN 40 to 63 Amps.

(b) MCB B curve SP 5 to 40 Amps

Supply and fix LED lights fitting 1x 22W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable Size from ceiling rose complete all as specified and as directed .Make :- Phillips/ Bajaj/CG

Supply and fix LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable Size complete all as specified and as directed .Make :- Phillips/ Bajaj/CG

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

Supply and fixing round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete.

S&F LED decorative Garden light for 360 degree indirect light IP-65 grade of protection ISI mark with high power LED of 10 watt with resistant to impact and corrison.Glare free and better uniformity warm yellow including fixing material PCC 1:2:3 B-2 , exca. and earth work after taking down old existing garden light all as specified.

S& F Study lamp with holder, bulb 10/9 watt & metal canopy with three core flexible copper conductor cable of suitable size complete.

M&L for earthing complete with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 Mtr below ground level) with top edge of earth plate not less than 1.5 Mtrs below ground level connected to GI wire 4 mm Dia as earth lead by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, including PCC (concrete chamber) shall be PCC 1:3:6 type C-1 uSI-ng 20mm graded stone aggregate, with fair finish internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire gauge mesh, 80 mm thick RCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI and charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) and specified including proviSI-on 20 mm dia medium grade pipe and watering pipe shall be 20mm bore medium grade, and including all excavation and earth work & connecting the earthing to an earthing test point complete all as specified & directed . NOTE: (i) The concrete pit shall be PCC 1:3:6 type C-140 mm thick pre cast cover slab of RCC(1:2:4) type B-1 uSI-ng 20 mm graded stone aggregate reinforced with 8 mm TMT bars @ 10 cm C/C on both SI-des with suitable cast iron handle shall be provided in lieu of cost iron cover shown in the electrical plate No.3 of MES SSR Part -1 (ii) item includes the cost of 7.5 m GI pipe for protection of GI wire. (iii) PCC pits extra cost of addtional length of watering pipe,bends elbows etc.shall be deemed to be included in the quioted rate. (iv) Item includes the cost of 7.5 mtr length Galvanised wire 4 mm dia.

Supply , laying , jointing and testing XLPE armoured heavy duty electric able with aluminium conductor 1100 volts grade of size 70Sq mm 3.5 Core complete all as directed.

M & L boring of holes under road pavment hard standing by trenchless technology using ultra sound technique and necessary machine incl HDPE pipe of 100mm dia suitable for 0.4 mpa working pressure complete all as specified and directed by Engr-in-charge.

M&L for Excavation in trenches in soft/loose soil n.exc 1.5 m wide and n. exc 1.5 m in depth for foundation or shaft, wells,cespits, manholes, pier holes, cable laying, sewage/ water line etc complete all as specified and directed.

M&L for Removal of surplus soil to a distance n. exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified.

M&L for Returning filling in soft/loose soil including spreading,watering,leveling and well ramming in layers not exc 25 cm complete all as specified.

M&L for sand cushioning with a layer of sand 80mm thick before laying of cable and 150mm thick after laying of cable to trenches complete all as specified and directed

M&L for brick protection cover of UG cable by old size bricks common burnt clay building bricks sub class `B’ laid dry and flat abutting each other with width equal to length of brick and gap between adjacent brick not exceeding 10mm complete all as specified and directed

Supply and laying galvanised iron pipe, medium grade 20 mm bore with all new fittings bends, elbows, tees, short pieces, connectors, backnuts, diminishing pieces, caps, plugs and unions, etc. of reqd size) trenches including jointing material etc complete all as specified and directed.

S & F Gun metal globe or gate valve (ISI marked), with iron wheel head, screwed both ends, suitable for 20 mm bore iron pipe and fixed including testing complete all as specifed and directed by Engr-in-Charge.

Cutting existing 50 mm bore GI wter supply pipe line in position for insertion for new tee for taping new pipe line with existing complete all as specified

PRAGATI BUILDERS (BID ID -3342062)

M/S ujjwal associates (BID ID -3341634)

SHAKSHI ENTERPRISES (BID ID -3349418)

M/S LADPURIA ENTERPRISES (BID ID -3341712)

sumit associates (BID ID -3341757)