Provn of cetain LBW, Special repair, revenue works and minor works at Mil Station Beas and Jandiala Guru under GE Kapurthala

Amount

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and pre-cast concrete articles and removing unserviceable materials from site of work complete all as directed.

Surface dressing not exceeding 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth ; for foundation, etc. getting out in soft / loose soil complete all as specified and directed

Demolition and breaking up 150 mm dia, drain pipes Salt glazed ware, AC or reinforced concrete set in cement mortar complete all as specified & directed.

Demolition& breaking up 200mm dia, drain pipes salt glazed ware, AC or reinforced concrete set in cement mortar complete all as specified & directed.

Removing excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n. exc 25 cm thick in soft /loose soil complete all as directed.

Material & Labour for plain cement concrete (1:4:8), type D-2, (using 40mm graded stone aggregates) in foundations, filling, mass concrete etc complete all as specified and directed.

Material & Labour for plain cement concrete (1:2:4), type B-2, (using 40mm graded stone aggregate ) in foundations, filling, mass concrete etc complete all as specified and directed.

M&L for brick work with sub class old size 'B' bricks, straight or curved on plan, exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M & L for 15 mm thick rendering on brick work or concrete surfaces in cement mortar 1:4, including using water proofing compound as per manufacturer's instruction surface finished even and fair complete all as specified & directed. (Note : Water proofing compound shall be measured and paid separately as supply only.)

M & L for 10mm thick rendering in cement mortar 1:6 on fair faces of brick work and finishing surfaces even and smooth without using extra cement complete all as specified & directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M & L for cement concrete (1:2:4) B-1 using 20mm graded stone aggregate as in lintels up to 1.5 m clear span, parapets walls, benching, coping, bed blocks and roof kerbs etc including use of necessary form work all as specified and directed by Engineer - in - Charge .

Extra for forming fair finished drain or channel inner girth 47cms in cement concrete, using extra cement including forms, moulds mitred/ stpped ends etc complete all as specified and directed.

S&F steel ventilators with top hung shutter including hinges, steel peg stay, complete all as specified and directed by engr-in-charge (Note : Glass/wire mesh and painting shall be measured and paid separately under appropriate item).

Supply & Fixing mild Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1979 grade St.-240 complete all as specified and directed.

Supply & Fixing for rolled mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, duly welded, with out any attachment conforming to Fe:410-W(Gde-E-250 ) quality-A complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F rolled mild steel Fe 410-W (Gde-E-250) quality-A in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. Within 20mm of the length indicated) complete all as specified and directed.

M&L for Preparation of new steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paintover a coat of red oxide primer complete all as specified & as directed.

Demolition of cement concrete in ground floors and pavings n. exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Material & Labour for 100mm thick Plain cement concrete (1:2:4), type B-1 (using 12.5mm graded crushed stone aggregate), as in sub base of floor/sunken floor etc., mixed with water proofing compound as per manufacturer's inststruction and finished the surface even and rough for receiving top layer complete all as specified and as directed. (NOTE: WPC shall be measured and paid separately here-in-after as 'supply only').

Material and labour for Machine cut kota stone slab flooring 20-25mm thick over and including 15mm thick screed bed in CM 1:6 , set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engr-in-Charge.

Taking down chowkat or frame with shutters n.exc 1.5 sqm each (without taking off shutters from the frame) complete all as specified and directed.

Demolition of reinforced cement concrete of any description & in any position not otherwise specifically provided for complete all as specified & directed.

Material and labour for pre-cast cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregates) as in cover slab for manhole and similar articles with plain faces and set in cement mortar (1:6) including necessary form work complete all as specified and directed. (NOTE: Reinforcement shall be measured and paid separately.)

Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified & directed.

Demolition floor, hearth or wall tiling or stone slabs, laid, beded & pointed in any mortar including removing rubbish off the premises complete all as specified & as directed.

M & L for 15mm thick in two layers (10mm+5mm) rendering in cement mortar 1:4 on other than fair faces of brick work and finishing surface even and smooth without using extra cement complete all as specified & directed.

M & L for preparation of new plastered surfaces of walls etc. and applying two coats of distemper oil emulsion over and including 3mm thick wall care putty & preparatory to distemper complete all as specified & directed.

S & F mild steel TMT bar 25 mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for step shape reqd complete all as specified and directed.

Supply and fix 10mm dia mild steel TMT bars as in reinforcement, cut to length, bent to shape required including cranking, hooking ends and binding with MS wire (annealed) not less than 0.90mm dia or occuring with clips complete all as specified and as directed by Engineer-in-Charge.

Supply & fixing mild steel TMT bars 6 to 8mm dia and over cut to length bent to shape required including cranking, hooking ends and binding with MS wire (annealed) not less than 0.90mm dia all as specified and directed by Engineer - in - Charge .

Material and labour for clearing blockage of Gully/floor traps to first man hole by Roding/pressure to clear blockage and removing the garbage out of the cantonment area without creating any nuisance and make the site neat & tidy to the entire satisfaction of the Engineer-in-Charge.

Material and labour for pumping out liquid or semi liquid sludge from sewage wells or septic tanks of any size or any depth mechanically and an open trench shall be made for disposal/ evaporation of liquid sludge. After use, the whole area shall be covered with bleaching powder and covered with soil about 15cm thick complete all as directed by the Engineer-in-Charge. Note: During the cleaning of sewage wells, the alertnate arrangements shall be made by contractor by temporary pumping for clearing sewage disposal.

Material and labour for cleaning of existing septic tank and sewage well (by closing the existing sewage system at last man hole and providing temporary Katcha drain for flow of sewage water), removing man hole cover and dewatering the liquid waste by mechanical pumping, removing the solid sludge mechanically up to the bottom of septic tanks and sewage well of any size including depositing the solid sludge in the pit providing by digging in near by septic tank of appropriate size, Covering the pit with bleaching powder and then by natural earth about 15cm thick layer, soil obtained from excavation after filling the solid sludge and making good completely hygienic, Opening the man hole after cleaning and relaying the man hole cover, complete work to be executed to the entire satisfaction of Engineer-in-Charge and as directed at site.

Material and labour for Cutting into existing manholes for connecting new drains, of any dia making good to pipe and rendering , cutting out existing benching for and forming branch channel (1/2 round or ¾ section) in cement concrete 1:2:4 type B1 (using 20mm graded crushed stone aggregates) finished smooth and reforming benching as required for 150 mm dia SGSW pipe complete all as specified and directed by Engineer-in-Charge

S&F, galvanised mild steel wire cloth, 0.56mm nominal dia of wire & average width of aperture 1.18mm & fixed with tinned tacks, or stainless steel wire staples complete all as specified & directed

M&L for framed work as in doors or gates and sign boards of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening duly cutting, bending, welding and fixing complete confirming to Fe 410-W (Gde-E-250) quality B complete all as specified and directed.

S & F, 30 mm thick, 2nd class hardwood Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides supplied & fixed to chowkats complete all as specified & directed.

S&F 250mm long mild steel sliding door bolts plate type stove enamelled black with bright bolt not less than 12mm dia with and including a minimum 8 bolt and nuts four on bolt plate & two on staple plate all as specified.

M & L for preparing new wood & wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer - in - Charge .

M&L for Hardcore of guage exc 63mm but n exc. 100 mm of broken stone aggregate, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface true surface all as spd and directed.

Material & Labour for 75 mm thick Plain Cement Concrete ( 1:3:6 ) type C-2 using 40mm graded aggregate as in plinth protection finishing the surface even and fair including making joints and filled with bituminous mastic mix propotion of bitumen and sand 1:2 complete all as specified and directed.

Material & Labour for 100mm thick cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregates) in sub base of flooring, finished even and rough to receive the topping layer complete all as specified and directed.

M & L for sand cushining /filling under floors 50 mm thick for laying floor finishesh all as specified and directed.

M & L for machine pressed precast concrete interlocking paver block any shape and size with gray cement and no pigment confirming IS 15658-2006 of 80 mm thickness M-40 Grade complete all as specified and as directed ,

M & L for welding not exceeding 2.5cm in length to the metal not exceeding 6mm thick complete all as specified and as directed by Engineer-in-charge.

Use & waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) for fair finished flat surfaces of concrete complete all as specified and as directed.

M&L for granite 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types over and including 15mm thick bedding layer in CM 1:6 complete all as specified & directed by Engineer-in-Charge.

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm complete all as specified and as directed.

Supply and fix 15mm bore bib tap with wall flange, cast copper alloy, chromium plated and screwed to iron pipes or union fittings complete all as specified and as directed by Engineer-in-Charge.

S&F Powder coated Anodised aluminium frame (Thickness of powder coating not less than 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.) hinge type B-21 100mm long (2 Nos) suitable handle (1 No.) complete all as specified and directed.

S&F Powder coated Anodised aluminium fly proof window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.) hinge type B-21 100mm long (2 Nos) suitable handle (1 No.) complete all as specified and directed.

S&F Powder coated Anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified.

S & F, 30 mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc (without sash bars) fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), supplied & fixed to chowkats complete all as specified & directed.

S&F aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified & directed.

Supply only 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 sq. m in each pane complete all as specified and directed by engr-in-charge.

S & F, 200 mm size, aluminium anodised , barrel tower bolts of extruded section & fixed complete all as specified and as directed.

S & F 150 mm long aluminium analized cast type handle all as specified and directed by Engr-in-Charge.

Supply 100mm long MS butt hinges medium wt colled rolled fixed to angled iron frame complete all as specified

M&L for reinforcement cement concrete (nominal mix) type B-0, 1:2:4 (12.5mm graded aggregate) slabs supported on walls complete for rough finished surface complete all as specified and as directed.

M & L for Reinforced cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in slab of septic tank, soak well, beam, lintal etc complete all as specified and as directed.

M & L for Reinforced cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in baffle wall etc complete all as specified and as directed.

Use and waste of form work of baffle wall,etc for smoth concrete complete all as specified and directed.

Use and waste formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and as directed by Engr-in-Charge.

M&L for joint free non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 ssqm but not exceeding 0.18 sqm, in floors etc, over and including 15mm thick screed bed in CM 1:6 , set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by engr-in-charge.

Material and labour for joint free coloured glazed ceramic tiles of size 350x250x7mm/450x350x7mm thick, as on vertical surfaces such as dados, skirtings etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour of tiles over and including backing coat 10mm thick cement mortar (1:4) complete all as specified and as directed by the Engineer-in-Charge.

S & F 125 mm long aluminium anodised cast type handle all as specified and directed by Engr-in-Charge.

Supply and fix 15mm bore bib tap with wall flange, cast copper alloy, chromium plated and screwed to iron pipes or union fittings complete all as specified and as directed by Engineer-in-Charge.

Taking up or down, steel tubing 15mm bore and connections including cleaning for refixing and removal from site complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 15mm bore galvanized steel water tubing, medium grade with all fittings fixed to wall, ceiling or laid in floors complete all as specified and directed by the Engineer-in-Charge.

S&F for 18mm thick high grade PVC boards fixed with screws to timber/steel frame work complete all as specified & directed.

S&F magnetic type catch fixed with screws to door frame complete all as specified and directed by Engineer-in-Charge.

Supply and installed for L-Shape Modular kitchen of commercial material with modern design, 19mm thick commercial grade laminated ply both side for making kitchen cabinets, Kitchen racks frame of Stainless Steel Grade 304, fancy handle 150mm size, Drawers frame should be telescoie channels, Hydro Auto close hinges, 20-25mm thick granite on counter top, Stainless steel sink as per reqd size(Each Kitchen), Matte & Gloss finishing with all asseries & fittings complete all as specified and as directed by Engr-in-Charge. (Make :Systematic) (Total 09 Nos of kitchens are involved).

M & L for RCC NP2 pipe 150mm dia bore and jointed in cement complete with collars as in culvert complete all as specified and directed.

M & L for RCC NP2 pipe 200mm dia bore and jointed in cement complete with collars as in culvert complete all as specified and directed.

M&Lfor cement concrete ( 1:3:6 type C2) bed to drain pipes of 150mm bore dia including packing under and haunching against the sides of pipes after they are laid and tested all as specified and directed.

M&L for cement concrete ( 1:3:6 type C2) bed to drain pipes 200mm bore dia including packing under and haunching against the sides of pipes after they are laid and tested all as specified and directed.

Taking down drainage pipes (any size and pattern), including all fittings, heads, shoes, bends, swan necks, etc. removal from site (measured overall as fixed along the centre line or fittings and accessories) complete all as specified and directed.

S&F PVC (SWR) pipes, 110mm bore, single socketed, in any length with rubber ring joints fixed to walls including taking down old userviceable pipes complete all as specified and directed.

S&F PVC (SWR) pipe 75 mm dia fixed as gas pipe to septic tank complete all as specified and as directed.

S & F PVC cowl 75 mm bore cowl fixed with pipe complete all as specified and directed.

S & F PVC cowl 110mm bore cowl fixed with pipe complete all as specified and directed.

Cutting existing road upto depth n. exc. 30cm & width 50cm for laying RCC pipe of 150mm internal bore including necessary earthwork & excavation upto a maximum depth of 1.2m beneath road bottom and making good the disturbed surface, including filling the trenches by spreading, leveling watering & well ramming the approved earth, relaying soling and PCC sub base 1:4:8 type D-2 100mm thick & finishing top with minimum of 100mm thick PCC 1:2:4, type B-2 (using 40mm graded stone aggregates) complete all as specified and directed by Engineer-in-Charge.

Material and labour for construction of soakage wells of size 3.00m dia & 4.50 m deep, excavation, in any type of soil, foundation in PCC 1:3:6 wells of honey combed brick masonry in cement mortor 1:4 and cover slab in RCC 1:1 1/2 : 3, type A-1 using 20mm graded crushed stone aggregate & TMT bars of 10mm & 6mm dia, PCC band in type B-1 (1:2:4) including interconnecting pipes, filling with brick bats complete all as specified and as shown in drawings and as by Engineer-in-charge.

S&F steel window 1.25mm thick box type (primer coated) ERW hollow P section of size 60mm x 25mm, 1.25 thick sheet single rebated comprises glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T-section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC (1:2:4) type B-1 Four Nos for each window including following fitting welded to frame shutter : (a) Hold fast, 150mm long of 12mm square bar made to shape-04 Nos per window (b) Handles of z section 100mm long (c) Stopper - 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges - 01 No per leaf (e) MS Pintal hinges of size 75mm x 75mm x 12mm-02 Nos per leaf (f) Fabrication & fixing arrangement as per drg No CEJZ/TD-7/07 sheet 1/3 to 3/3. Note : Glass and painting shall be measured and paid separately under appropriate item etc complete all as specified and directed.

S&F steel window 1.25mm thick box type (primer coated) ERW hollow P section of size 60mm x 25mm, single rebated comprises gauzed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T-section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC (1:3:6) type C-1 Four Nos for each window including following fitting welded to frame shutter : (a) Mild Steel Hold fast, 150mm long of 12mm square bar made to shape-04 Nos per window (b) Handles of z section 20mm x 100mm long (c) Stopper - 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges - 01 No per leaf (e) MS Pintal hinges of size 75mm x 75mm x 12mm-02 Nos per leaf (f) Grills made out of MS square bar 12mm dia welded to FI frame complete all as specified and shown on drawings. Note : Wire mesh and painting shall be measured and paid separately under appropriate item etc complete all as specified and directed.

M&L for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.

S&F, 4 mm thick, Non asbestos fibre cement building boards fixed to timber/GI/Aluminium framework with screws as in ceiling complete as specified and directed.

M & L for preparing new surfaces of ceiling and applying three coats of white wash complete as specified and directed.

S&F Cast Iron floor trap 100mm dia with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1 (including cutting in existing floor,removing the old and place the new pieces and making good the disturbed portion) complete all as specified and directed.

M&L for point wiring for one light or one fan point controlled by one switch or with one switch and regulator with PVC unsheathed single core miltistranded copper conductor (FRLS) cable of size 1.5Sqmm (nominal area) in and including PVC conduit 20mm bore by cutting chases in wall by cutter and making good the surface in cm 1:3 and to the original specification and cast iron/pressed steel concealed terminal boxes including providing 3mm thick plastic laminated sheet cover (Hylem) including one run of PVC insulated copper conductor (FRLS) cable of size 1.5 Sqmm with green insulation as earth wire and connected to earth dolly complete all as specified. (Switch/Socket outlet to be measured & paid for separately).

All as per ser item 96 above but for 3 pin socket out let 5 Amps on same board.

All as per ser item 96 above but for 3 pin socket out let 5 Amps on independent board

All as per srl item No 96 here in before but for 3 pin socket outlet 5 Amps on independent board with PVC unsheathed copper conductor cable of size 2.50 Sqmm including copper earth wire of size 2.50 Sqmm and connected to common earth dolly complete all as specified. (Switch/socket to be measured & paid for separately)

Supply and fix switch piano flush type single pole one way 5 Amp (ISI Marked) complete all as specified and as directed by Engineer-in-Charge.

Supply and fix switch piano flush type single pole one way 15 Amp (ISI Marked) complete all as specified and as directed by Engineer-in-Charge.

Supply and fix socket outlet 5 pin 5 Amp flush type multipurpose complete all as specified and as directed by Engineer-in-Charge.

Supply and fix socket out let 2 in 1, 3 pin 5/15 Amp flush type (ISI Marked) complete all as specified and as directed by Engineer-in-Charge.

S&F surface mounting energy saving LED tube light fitting/Batten with LED T8 Tubelight with PC body, 1x20W, 230V, Cat Part No of Batten DMLN1LT8-16 & Cat Part No LT8-20-865-2 for LED T8 Tube light Make-Crompton or equivalent complete with all accessories.

Supply and fix in repairs; MCB, 6 to 32 Amp, SP, 240 Volts 10 KA breaking capacity complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing MCB single pole 32 Amps 240 Volts SPN , B Series Product Code CSMBS1B6N to CSMBS1B32N Make- C&S or equivalent in Havells/GE/L&T/Legrand)

Supply and fix ceiling rose, surface Bakelite 65 x 50 mm of three terminals PVC/Polycarbonate, isolated body (ISI Marked)complete all as specified and as directed by Engineer-in-Charge.

Supply and fix lamp holder angular type,PVC/Polycarbonate type with back plate suitable for batten fiitng with and including 1 x 9W LED bulb of approved make complete all as specified and as directed by Engineer-in-Charge.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm & 6 mm thick surrounded with charcoal and salt, buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by galvanized iron 15 mm dia light grade pipe and watering pipe shall be 20 mm bore light grade including all excavation and earth work in any type of soil, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete all as directed.The concrete pit shall be PCC 1:3:6 type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I.Item includes cost of 7.50m earth lead wire/strip. Any variation in length shall be adjusted through deviation order. PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe, bends, elbow etc shall be deemed included in the unit rate. Item includes the cost of 7.50m GI pipe for protection of earth wire/strip Any variation in length shall be adjusted through deviation order.

S&F 1100 Volts grade heavy duty cable PVC insulated stranded aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 meter apart including 4mm suspension wire, one twin core cable flat or round of 10 Sqmm cable complete all as specified and as directed by Engr-in-Charge.

S&F House service bracket (Hook type) complete with 3.0 Mtr long made up with G.I pipe 40mm dia Med grade two Nos 90 degree bends, MS hooks and stay or guy complete all as specified and as directed by Engr-in-Charge.

Supply and fixing LED bldg security light fitting 15 watt Powder coated pressure die cast aluminium compact LED security light including 1.5 mtr long 40 mm bore GI pipe mounting bracket made to shape for fixing on wall with 40 mm x 6 mm flat iron clamp 02 numbers with 16 mm dia bolts, nuts and washers all as specified and directed by Engineer-in-Charge.Make- Crompton Cat Part No LSTS-15-CDL or equivalent in Bajaj/Philips/C&S/Havells : Contractor shall provide 1 years written manufactures warranty for the LED fixture complete including driver from the certified date of completion.

Supply & Fix exhaust fan 150 mm sweep, PVC Body, single phase ,230/240 V,AC with louvers including making of hole on wall for passing out air and provision of flexible three core copper conductor cable of 23/0.0076 up from ceiling rose to fan and grouting 04 Nos bolts in wall. Make :-Crompton Model Transair 6".

COSMO BUILDERS