SPECIAL REPAIRS TO VINTAGE BLDG NO 20, THE MALL OF ROCKET REGIMENT UNDER GE NASIRABAD.

Amount

Demolition of cement concrete (unreinforced ) in floors and pavings n. exc 15cm thickness (above or below GL) complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling floor, hearth or wall tiles, including cement mortar, removing serviceable tiles from site & rubbish off the premises, complete all as specified and directed.

Taking down cement or cement lime plaster or stone / brick wall, ceiling including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Taking down chowkhat or frames with shutter (without taking off shutter from the frame ) area exc 1.5 Sqm but n. exc 4.0 Sqm each complete with hold fasts etc complete all as specified and directed.

Taking down chowkhat or frames with shutter (without taking off shutter from the frame ) area n.exc 1.5 Sqm each complete with hold fasts etc complete all as specified and directed.

Demolition of brick work or stone masonary built in cement mortar etc complete all as specified and directed.

M & L for brick work with flyash bricks, straight or curved on plan exc 6M mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L for rendering in cement mortar (1:6), 15mm thick on other than fair faces of brick work / stone masonary surfaces finished even and smooth without using extra cement, complete all as specified and directed.

M & L for preparation of newly plastered antifungal treatment surface of wall and applying two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour over one coat of alkali resistant priming paint complete, as per manufacturer's specification complete all as specified and directed.

M & L 15mm thick rendering in cement mortar (1:4) mixed with water proofing compound on other than fair faces of brick / stone masonary surfaces, finished even and smooth without using extra cement, complete all as specified and directed. Note :- WPC measured and paid separately.

M & L for rough cast plaster mix with crusted stone (6-10mm), sand and cement in the ratio 1: 1.5: 1, over 15mm thick ready mix plaster rendering in CM 1:4 on stone / brick masonary wall surfaces complete all as specified and directed.

M & L for preparation of new plastered surfaces of wall and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over plastering surfaces, complete all as specified and as directed. Make :- ASIAN/APEX/BERGER (Weather coat all guard)

M & L 25mm thick PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate as in floors complete all as specified and directed.

M & L non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 Sqm but not exc 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding in cement mortar 1:6 complete all as specified and directed.

M & L for glazed ceramic coloured tiles 7 to 8mm thick in vertcial surfaces of size exceeding 0.11 Sqm but not excceding 0.18 Sqm set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick screed plaster in cement mortar 1:4 complete all as specified and directed.

M & L for digital ceramic elevation matte glossy finish coloured tiles 7 to 8mm thick in vertcial surfaces of size exceeding 0.11 Sqm but not excceding 0.18 Sqm set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick screed plaster in cement mortar 1:4 complete all as specified and directed.

M & L for vitrified ceramic tiles light shade10mm thick (square / rectangular ) polished, area of each tiles exc 0.42 Sqm not exceeding 1.00 Sqm, in floor etc set and jointed in neat cment slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM 1:6 complete all as specified and directed.

M & L for Pre-polished machine cut kota sotne slab, 20-25mm thick over and including 15mm thick screed bedding in cement mortar 1:6 as in floors, laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab, complete all as specified and directed.

M & L for Pre-polished machine cut kota sotne slab in skirting / steps / risers of reqd size, 20 to 25mm thick & including 15mm thick screed bedding in cement mortar 1:4 as in floors, laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab, complete all as specified and directed.

M & L RCC, type B-1 (1:2:4) using 20mm graded aggregate in, slab supported on wall, walls beams and columns in floors, roof landings, Chajjas and platform etc. including form work, complete all as specified and directed.

M & L for TMT bars 10 mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending, spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M & L for marbonite tiles any shade, 12mm thick (square / rectangular ) polished, area of each tiles exc 0.42 Sqm not exceeding 1.00 Sqm, in floor etc set and jointed in neat cment slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM 1:6 complete all as specified and directed.

S & F for Ist class HW, plain, solid, straight chowkhats & frames, wrought, framed, rebated on the solid, rounded or chamfered, put together glue pinned at joints complete all as specified and directed.

S & F 35mm thick 1st class hard wood solid Flush shutters (design type), with wooden polish complete all as per specified and directed.

S & F for 150mm long stainless steel barrel tower bolts complete all as specified and directed.

S & F for 150mm long Stainless steel pull handles, complete all as specified and directed.

S & F for Stainless steel butt hinges, ISI marked of size 100mm, complete all as specified and directed.

S & F for 300mm long Stainless steel sliding door bolt with hasp and staple (bolt type) and fixing clips, complete all as specified and directed.

S & F for 300mm ordinary Mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S & F in repairs 150mm long dual leg floor door stopper of alumunium alloy body and tongue anodised with hard drawn steel spring fixing on door, complete all as specified and directed.

S & F for continous (Piano) hinges, mild steel, bright finish, width of flaps (when open) 30mm complete all as specified and directed.

S & F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing using single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet, reinforced with MS square tube and fixing in opening as specification & drawing complete all as specified and directed.

S & F for factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick, (styles) with 2,4 or 6 raised panel design with 2mm thick moulded prelam (Nut Brown colour ) PVC sheet on the front face & 2mm prelam (Nut Brown colur ) PVC sheet on back face, and fixing inthe frame at site as per specification and drawing on page 161 of SSR (Part -II ) 2020 complete all as specified and directed.

S & F for 150mm long aluminium anodised barrel tower bolts of extruded section all as specified and directed.

S & F for 150mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F for 100mm butt hinges extruded aluminium alloy with galvanised mild steel hinge and anodised ISI marked and fixed, complete all as specified and directed.

S & F for in repair Deco door seal size 1.5" width door bottom sealing strip draft Excluder stopper with aluminium plate & nylon bristles for weather stripping complete all as specified and directed.

S & F for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight,mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P.brass/ stainless steel screws, all complete as specified and directed.

S & F for 5.5mm thick sheet glass exc 0.5 sqm with solar control filim 50 micron ordinary quality including necessary fixing items, complete all as specified and directed.

S & F 12mm thick Toughned glass as in hinged doors, partitions, automatic door and similar work including cutting to shape, drilling holes, 300mm SS Handle,hinges etc.complete all as specified and directed.

M & L providing 50x50mm aluminium anodised grills mesh for fixing in wooden gauged door shutter weight not less than 1.2Kg/ Sqm complete all as specified and directed.

S & F for stainless steel wire cloth, 0.36mm nominal dia of wire and average width of apertature 1.40mm and fixed with tinned tacks or stainless steel wire staples all as specified and directed.

S & F for 4mm thick etched glass, pin head type and glazing in square exc 0.50 Sqm in each pane, complete all as specified and directed.

S & F for in repairs 25mm dia wooden curtain rod and decorative type wooden knobs and curtain rod bracket with wooden U shaped support clamp suitable for 25mm dia rod complete all as specified and directed.

Taking down old unserviceable 15mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed.

Taking down old unserviceable 20mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed.

Taking down old unserviceable 25mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed.

S & F for 15mm GI water tubing( Concealed type), medium grade, galvanised with all fittings (fixed to walls, ceiling or laid in floors/ trenches) complete all as specified and directed.

S & F for 20mm GI water tubing, medium grade, galvanised with all fittings (fixed to walls, ceiling or laid in floors/ trenches) complete all as specified and directed.

S & F for 25mm GI water tubing, medium grade, galvanised with all fittings(fixed to walls, ceiling or laid in floors/ trenches) complete all as specified and directed.

Refixing old 15mm GI tubing (Concealed type) galvanised with new fittings and fixed to walls, ceiling or laid in floors, trenches including necessary cleaning, cutting, screwing complete all as specified and directed.

Refixing old 20mm GI tubing galvanised with new fittings and fixed to walls, ceiling or laid in floors, trenches including necessary cleaning, cutting, screwing complete all as specified and directed.

Refixing old 25mm GI tubing galvanised with new fittings and fixed to walls, ceiling or laid in floors, trenches including necessary cleaning, cutting, screwing complete all as specified and directed.

S & F for in repair tubular towel rail brass chromium plated 20mm dia 'D' type 60cm long,complete all as sped & directed. Make: Prima or Equivalent. (Cat No.PSS-4503-A)

S & F for in repair towel ring brass chromium plated,complete all as sped & directed. Make: Prima or Equivalent. (Cat No.PSS-4503-B)

S & F for in repair Paper Holder brass chromium plated,complete all as sped & directed. Make: Prima or Equivalent. (Cat No.PSS-4503-F)

S & F for in repair CP Amaze square shower with arm (8'' x 8'') complete all as specified and directed.

S & F for in repair PVC Multi utility Mirror cabinet , complete all as specified and directed.

S & F for in repair Glass corner shelf 300mm with brass brackets, complete all as specified and directed.

S & F for inrepair vitreous china white table top wash basins (660x430x140mm) and connecting pipe complete all as specified and directed. Make:- RAK Aurex or Euivalent

S & F in repair vitreous china wash down one piece closet (White) size 747x370x650mm, with integrated cistern, incl soft close seat cover and twin flush fittings etc. complete all as specified and directed. Make: Prayag or equivalent (Cat No. 4353)

S & F for in repair health faucet cast copper alloy chromium plated with flexible chrome hose and wall hooks complete all as specified and directed.

S & F for cast copper alloy chromium plated bottle trap fixed to WHB and wall complete all as specified and directed. Make:- Parryware T3201A1 or equivalent

S & F for looking mirror 900x600x6mm with frame, with chromium plated brass screws and cup washers fixed to wall complete all as specified and as directed. Make : Prayag or equivalent (Cat No. BLM-03 F)

S & F for in repair Soap dish fancy type, fixed to plugs with chromium plated brass screws embedded in the wall complete all as specified and directed. Make : Prayag or equivalent (Cat No. BA-15)

S & F for in repair PVC connection, heavy duty 15mm bore, 60cm long with 2 Nos PTMT nuts of approved quality complete all as specified and directed.

S & F for in repair, 15mm bore Brass CP basin mixer for mixing hot & cold water for wash basin screwed down for iron pipe and fixed complete all as specified.

S & F for in repair, 15mm bore Brass CP wall mixer three in one system with bend set Telephonic shower and 1.5 m tube with stand, complete all as specified.

S & F for in repairs 15mm bore cast copper alloy chromium plated fancy bib tap long body , screwed for iron pipe complete all as specified and directed.

S & F for in repair fancy type angle valves 15mm bore , cast copper alloy chromium plated, screwed down high pressure screwed both ends for iron pipe or for unions and fixed etc complete all as specified and directed.

S & F for in repair 15mm bore stop valves (concealed), chromium plated cast copper alloy,with long shank and cap (Concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions fixed complete all as specified and directed.

S & F for mild steel framed work such as grills, grating cooler stands, water tank staging etc, with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

Taking down 100mm / 75mm dia AC/PVC/CI pipe (any size or pattern ) including all fitting, heads, shoes, bends and removing from sites complete all as specified and directed. Note :- Measured over all as fixed along the centre line over the fittings and accessories

S & F for 110mm PVC (SWR) pipes single socketed in any length with rubber joints fixed to wall or laid in floors / trenches with & including existing / new MS stack clamps of FI 50 x 3mm complete all as specified and directed.

S & F for 75mm PVC (SWR) pipes single socketed in any length with rubber joints fixed to wall or laid in floors / trenches with & including existing / new MS stack clamps of FI 50 x 3mm complete all as specified and directed.

S & F for 110mm bore PVC (SWR) bend / shoe of any radius with access door, complete all as specified and directed.

S & F for 75mm bore PVC (SWR) bend / shoe of any radius with access door, complete all as specified and directed.

S & F for in repairs PVC (SWR) floor trap/ Nahani trap 75mm, plain with grating including jointing to waste pipe fixed in cement concrete type (1:2:4) complete all as specified and directed.

S & F for in repairs 110mm bore PVC (SWR) vent cowl complete all as specified and direted.

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/ loose / hard/dense soil complete all as specified and as directed.

Demolition and bracking up drain pipe SWG line set in CM of description, 150mm dia including side packing / haunching complete all as specified and directed.

M & L for PCC 1:3:6 type C-2 using 40mm graded aggregate for bed concrete to drain pipe packing under hunching for sides for 150mm dia SWG pipe lines complete all as specified and directed.

M & L for SWG drain pipe grade 'A' 150mm dia laid in trenches incl jointing in CM 1:3 complete all as specified and directed.

Returning and filling in approved earth including levelling spreading watering and well ramming in any layers n. exc 25cm thick complete all as specified and directed.

Removing excavated materials n. exc 100m and depositing where directed and complete all as specified and directed.

M & L cement concrete 1:2:4 using 40mm graded aggregate as in surface channel and drain complete all as specified and directed.

Extra for fair finishes drain or channel 30cm and over in girth in cement concrete using extra cement including forming mounds metred /stopped ends etc complete all as specified and directed.

M & L 75mm thick cement concrete type D-2 1:4:8 (40mm graded stone aggregate ) as in floors / pavings complete all as specified and directed.

M & L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and no pigment coloured, reflective type of approved quality complete all as specified and directed.

M & L for sand filling under floor in foundations inclding watering and consolidation complete all as specified and directed.

M & L for providing precast cement concrete 1:3:6 Type c1 using 20mm graded aggregate as in kerbs stone (100mm thick) or mud stops, rounded or chamfered on edges complete fixed in position & set in CM (1:4) incl necessary excavation required & removal of spoil to a distance exc 50 m complete all as specified and directed.

M & L PCC (1:3:6) type C-1 using 20mm graded stone aggregate, 75mm thick as in plinth protection/flooring etc. finished fair & even laid in alternative bays n. exc 2M in length and joints filled with bitumen mastic 1:3 complete all as specified and directed.

M & L for preparation of new steel surfaces over 10 cm width or girth & applying two coats of synthetic enamel paint of 1st quality, complete all as specified and directed.

M & L for preparation of old painted wooden surfaces of any description over 10cm width or girth & applying one coat of synthetic enamel paint of approved quality, tint to achieve glossy finish, complete all as specified and directed.

M & L for complete removal of existing treatment of old plastered surfaces of wall / Mangalore tile and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & ungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over plastering surfaces, complete all as specified and as directed. Make :- ASIAN/APEX/BERGER (Weather coat all guard)

Taking down existing tar felt or of any description including cement plaster or concrete of any thickness from the roof surfaces of building including cleaning the surfaces in all respect & preparing it for further treatment & removing rubbish from site complete all as specified and directed.

M & L for rendering 10mm thick in CM 1:4 mixed with water proofing compound @ 3% by weight of cement on fair faces of RCC/stone patti roof surfaces complete all as specified and directed. Note :- WPC will be measured and paid separately.

M & L for 40mm thick (avergae consolidated thickness) PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate laid in slope as in padding, finished even and smooth on existing slope including provision of 'V' shaped groove 6mm wide and 10mm deep at 1.20 metre interval or parts thereof, both ways on top of PCC padding and filled with mastic bitumen of (1:1) proportion complete all as specified and directed.

M & L roof treatment with APP modified polymeric water proofing membrane, 3mm thick having centre core not less than 100 micron high molecular high density polyethylene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 mircron HMHDPE film weight not less than 2.60 kg/ Sqm applied with bonding material using blown type bitumen primer Grade 85/25 @ 1.20 Kg/Sqm over bitumen primer conforming to IS -3384 @ 0.40 Kg /Sqm with final coat of bonding bitumen grade 85/25 @ 1.20 Kg /Sqm over APP membrane with all overlaps complete all as specified and directed.

Dismantling of existing unserviceable RCC/PVC water tank and S & F for 1000 Litres capacity rotational moulded polythene water storage tanks(cylindrical vertical with closed top ) hoisted & fixed in position complete all as specified and directed.

S & F for 20mm ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe of 20mm dia and fixed (minimum weight 210 gms) complete all as specified and directed.

Dismantling complete and S & F in Roof tiles, Mangalore pattern, interlocking at side joints, laid dry, complete all as specified and directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc.) any thickness, including cover fillets etc complete all as specified and directed.

S & F Solid PVC Wall Lining consisting of 5mm thick any colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and directed.

S & F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame complete all as specified and directed.

S & F for in repair false ceiling with Everest Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm,complete all as specified and as directed.

S & F in repairs 18/19mm thick MDF board one side laminated decorative type with decorative face veneer on one face fixed complete, including teak wood lipping 19 x 6mm thick fixed with nails in shelves, partition and palmet boxes, shelves, almirah book cases, toilet boxes, racks, cup board shutter and similar works all as spepcified and directed.

S & F for in repair stainless steel Soft Close hinge with assembly, complete all as specified and directed. Make:- Item Code -5070 of Godrej.

S & F in repair 125mm oval shape fancy brass handle, complete all as specified and directed.

S & F in stainless steel basket (plain) of approved quality of size 520 X 485 X 100mm complete all as spepcified and directed. Make :- Godrej SS 304 (Item Code -6154)

S & F in stainless steel plate / Thali basket of approved quality of size 520 X 485 X 200mm complete all as spepcified and directed. Make :- Godrej SS 304 (Item Code -6168)

S & F in stainless steel cutlery basket of approved quality of size 520 X 485 X 100mm complete all as spepcified and directed. Make :- Godrej SS 304 (Item Code -6162)

S & F in stainless steel cup & saucer basket of approved quality of size 520 X 485 X 100mm complete all as spepcified and directed. Make :- Godrej SS 304 (Item Code -6159)

S & F in stainless steel two shelf pull out basket of approved quality of size 150 X 485 X 430mm complete all as spepcified and directed. Make :- Godrej SS 304 (Item Code -6169)

S & F in stainless steel ball bearing basket / trolly /Drawer channel 50cm long, complete all as spepcified and directed. Make:-Item Code -8178 of Godrej

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc complete all as specified and directed.

Disconnecting and taking down unserviceable sub main wiring of any size including steel/PVC conduit and accessories & removing from site and making good the disturbed surfaces, complete all as specified and directed.

Taking down carefully by unscrewing from boards / outlet boxes, fittings and fixtures such as switches, sockets etc for re use at site or carrying to the store(To be measured only when found serviceable in all respects complete for re use.) complete all as specified and directed.

M & L for point wiring with 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed cable in and including PVC rigid non metallic conduit medium grade not less than 20mm dia ISI marked and fittings and accessories concealed in walls/roof/ ceiling with suitable size of sunk type pressed steel modular terminal box and modular white cover plate with frame for suitable module as per site requirements for mounting of modular switches, sockets, fan regulator etc and one green colour cable of 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed as earth wire up to common earth and connected to earth for the following, complete all as specified and directed:

All as per Item No 121.00 but One light point controlled by one, one way switch.

All as per Item No 121.00 but One Ceiling fan/wall fan/exhaust fan controlled by one, one way switch.

All as per Item No 121.00 but One three pin 5 Amp socket on same board with other switches.

All as per Item No 121.00 but One three pin 5 Amp socket on independent board.

All as per Item No 121.00 but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 1.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth etc complete all as specified and directed.

S & F for of modular switch 1 way 6/10Amp , 1 module, complete all as specified and directed.

S & F for of modular switch 1 way 16Amp, 1 module, complete all as specified and directed.

S & F for of modular socket 6Amp, 2/3 pin combined 2 module complete all as specified and directed.

S & F for of modular socket 6Amp/16 Amp, 2/3 pin combined 2 module complete all as specified and directed.

S & F for modular stepped type ceiling fan regulator, 230 volt AC, 2 module, complete all as specified and directed.

S & F for ceiling rose surface bakelite 3 terminals 63.5 x 17 mm etc complete all as specified and directed.

Taking down existing exhaust fan & wall mounted fan and re use at site or carrying to the store(To be measured only when found serviceable in all respects complete for re use.) complete all as specified and directed.

S & F for exhaust Fans AC single phase 230/240 volts of size 300 mm sweep with louver including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed.

S & F for of ventillation fan 300 mm sweep non metallic white colour including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed. .

S & F for of lamp holder PVC/polycarbonate type with back plate complete all as specified and directed. Make : Cona / SSK / Havells

S & F for LED box type tube light fitting 20 watt, cool day/warm/ white light with made up of CRCA sheet with pre wired double sided connections including 1x20 watt retrofit LED tube rod with extruded aluminium body , PC diffuser and inbuilt driver , double sided connection, complete with all accessories internally prewired etc complete all as specified and directed.

S & F for ceiling fan 1200 mm sweep , 230 Volts, AC , 50 Hz, copper winded motor, BE star rated white colour complete with motor, blade set of three nos , down rod, canopy, shackle assy etc complete all as specified and directed.

S & F for wall mounted decorative luminarie fitting suitable up to 9/10 Watt LED lamp/filament lamp champagne gold finish fixture with plastic body suitable for B22 Base etc complete all as specified and directed. Make: Havells , Model- LHFOECE1TZ1B014, LHFHANDBTN1K007, LHFOAJE2TZ1I060 and LHFHANDBTN1M007 or equivalent model of Mepro/Philips

S & F for LED light fitting mirror type , cool day/warm/ white light with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size etc complete all as specified and directed.

S & F for LED light fittings, 10 W bulk head luminaries 230V, 50 Hz complete with all accessories and including cool day/warm/ white light connecting up with three core copper conductor cable with suitable size complete all as specified and directed.

S & F for LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics alongwith bracket made of 32 mm GI pipe , 1.2 mtr length complete with IP 65/66 protection etc complete all as specified and directed.

S & F for recess mounted 2' x 2' LED luminarie 36 watt, cool day/warm/ white light with white powder coated CRCA housing with LED driver, efficiencey >100 Lm/w complete all as specified and directed. Make:- Crompton/Havells/Philips

M & L for submain wiring with two single core PVC insualated, unseathed, FRLS, 1100 volts grade 6 sqmm multi stranded copper conductor cable drawn through and incl 25 mm dia PVC non metallic rigid concealed conduits and the conduits accessories incl one run of green colour earth continuity conductor with 6 sqmm multi stranded copper conductor cable etc complete all as specified and directed.

M & L for submain wiring with two single core PVC insualated, unseathed, FRLS, 1100 volts grade 4 sqmm multi stranded copper conductor cable drawn through and incl 25 mm dia PVC non metallic rigid concealed conduits and the conduits accessories incl one run of green colour earth continuity conductor with 4 sqmm multi stranded copper conductor cable etc complete all as specified and directed.

M& L for TV Socket incl PVC conduit and co axial cable wire etc complete all as specified and directed.

M& L for Telephone socket incl PVC conduit and telephone wire etc complete all as specified and directed.

S & F single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amp MCB SP `C' series for AC complete all as specified and directed.

Taking down and S & F for of Change over Three Pole Neutral AC 100 Amp, with bolted type fuse in sheet enclosure with fuses complete all as specified and directed.

S & F for wall fan of size 300 mm sweep, Speed upto 2100 RPM, Air Delivery 90 CMM, 230/240 volts including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed. Make:- Havells, Bajaj, Usha

S & F for in repair surface mounted LED downlight 18 watt round shaped , Slim surface mounted LED panel with cool day/warm/ white light premium diffuser to ensure glare free & even light distribution complete all as specified and directed. Make Havells, Model -Trim Cosmo Surface Round, Cat Part No LHEAAHP7IL1W018, or equivalent model of Philips/Compton

S & F for storage type 25 liter geyser water heater electrical operated 230 volts including connecting inlet/outlet/vent pipes, electric/earth connections, mounting bolts, nuts and carrying out testing for proper functioning of all as directed.

S & F for of vertical TPN distribution board , IP-43 double door metal, 4 way , made out of CRCA sheet steel , factory made powder coated with insulated vertical phase bus bars , shrouded neutral bars, earth bars, colour coded interconecting wire set , blanking plates suitable for up to 125 amp MCCB's as incomer and MCB's SP/TP as outgoing complete all as specified and directed. Make : Legrand/Schneider/Seimens Note: MCB DB, MCCB and MCB's will be of same make.

S & F for MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door, IP-43, DB's made out of CRCA sheet steel enclosure, recessed type, factory made powder coated, 8 way, 240 volts suitable for housing MCB's and isolator's complete in all fixing material/accessories etc complete all as specified and directed. Note : MCB DB and MCB will be of same make.

S & F for of MCB distribution board TPN 4 way, 415 volts, double door, with 200 Amps rated bus bar, neutral bar with shrouds, earth bar, IP-43 , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCBs as incomer and outgoing including blanking plate complete all as specified and directed.

S & F for of MCB TPN 100 Amp capacity, 415 volt, complete all as specified and directed. Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

S & F for in repairs MCCB, 100 Amp, 4 Pole, 25 KA, 415 V, thermal magnetic release type, Ics=100 % Icu, with adjustable overload setting and adjustable short circuit setting , including spreader terminals and phase barriers complete all as specified and directed. Make- Legrand/Siemens/Scneider/Havells

S & F of MCB SP, 240 volt, 6 Amp to 40 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F of MCB SP, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F of MCB SPN, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F for of MCB TPN, 415 volt, 63 Amp capacity,10 KA, 'C' curve complete all as specified and directed.

M & L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unsv existing earthing etc complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core etc complete all as specified and directed.

S & F for tubes light grade GI tubing 40 mm dia with all fitting laid in trenches, fixed on pole/on wall for cable protection etc complete all as specified and directed.

Supply & spreading in trenches dry river sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed. Note:- Depth of sand cushioning will be measured after punning down and levelling the sand properly.

M & L for laying of bricks locally available sub class 'B' bricks, non-modular sizes as per IS 1077: 1992 for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable all as directed.

Shree Sai Ram Enterprises (BID ID -3260594)

GOMA CONTRUCTION COMPANY (BID ID -3263447)