SPECIAL REPAIR TO BLDG NO P-24 (OTM ACCN) AND P-25, PROVN OF SINK AND MARBLE SLAB AT OFFRS MESS COOK HOUSE (BLDG NO. P-139) AND PROVN OF CABINETS IN OR ACCN (BLDG NO P-136) AT FORT WILLIAM UNDER GE (FW) KOLKATA

Amount

Dismantling of floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing tiles from site and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for, all as specified and as directed by the Engineer-in-Charge.

Demolition of Cement Concrete (un-reinforced) in Ground Floors and Pavings not exc. 150mm thickness (above or below Ground Level), complete all as specified and as directed.

Taking down cement plaster on brick or concrete surfaces incl racking out joints, hacking for key, scrubbing down with water etc. all as specified and directed.

Dismantling of Asbestos cement corrugated, semi-corrugated sheet in roof covering complete all as a specified and as directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling boarding, any description, any type, fixed in any position with nails incl cover fillets complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone concrete or brick surrounds glazed with putty or fixed with beads complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames, glazed with putty or fixed with beads complete all as specified and directed.

Taking down chowkhats or frames with shutters (w/o taking off shutters from the frames) area not exceeding 1.5 sqm each and removing from the site complete all as specified and directed.

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L brick work with sub class'B' fly-ash bricks, straight or curved on plan exc 6m radius buit in cement mortar 1:6 complete all as a specified and as directed.

M&L brick work with sub class'B' fly-ash bricks, straight or curved on plan exc 6m radius buit in cement mortar 1:4 complete all as a specified and as directed.

M&L for use and waste for form work to sides and soffits of floor or roof beams , beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams for rough finished surfaces of concrete flat complete all as specified and directed

M & L for RCC type B1 1:2:4 (nominal mix) ( 20mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5 mtr span complete all as specified and as directed.

M&L TMT Bars 10 mm dia and over, cut to length, bent to shape required including crank-ing, bending and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm, complete all as specified and as directed.

M&L TMT Bars 6 - 8 mm dia and over, cut to length, bent to shape required including crank-ing, bending and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm, complete all as specified and as directed.

M&L for TMT bars 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders cut to length , bent to shape required as in reinforcement and binding with MS wire (annealed ) not less than 0.90 mm dia complete all as specified and directed .

M & L for precast RCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in cover slabs and the like including providing necessary form work etc, set in cement mortar (1:4) complete all as specified and as directed by the Engineer-in-Charge. (Note : Reinforcement to be measured and paid separately).

S&F 0.50 mm thick TCT (total coated thickness) pre-coloured galvalume sheets with minimum base metal thickness of 0.45 mm, single skin high rib/multi rib profile galvalume sheeting having 1000-1020 mm width and 28-30 mm high crest @ maximum 250-255 mm pitch (centre) with sheets manufactured out of 0.50 mm this TCT (total coated thickness) high tensile galvalume sheets having tensile strength 550 MPA with 18-20 micron top coat over 5 micron primer and 8-10 micron alkyld backer zinc aluminium alloy AZ-150, sheets having a dip metallic zinc (43.5%0 aluminium (55%) & silicon (1.5%) with total mass coating of 150 gms/sqm on both sides, having wide pans with minimum 3 small stiffening ribs for effective water shedding and special male/female ends with full return legs on laps for purlin support and fixed as per existing profile of roof complete all as specified and directed.

All as per Item No. 20 above but 0.50 mm thick coloured plain galvalume sheet as in ridge/valley gutter of roof.

M&L False ceiling with 'E' board "Classic", reinforced, designer series, board with HPSC of size 600 mm x 600 mm x 4 mm thick fixed on aluminium snap grid to support the boards/files with aluminium anodised main 'T' section 36mm x 25mm x 1.40mm cross tee 23.50mm x 23.50mm x 1.40mm thick and aluminium angle 25mm x 25mm x 1.40mm as on edges/sides, fixed to ceiling with hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long and applying two coats of oil bound distemper over a coat of alkali resistant primer on exposed surfaces complete complete all as specified and as directed. (NOTE: Quoted rate shall be deemed to be inclusive of the cost of ceiling board)

S&F 10 to 12mm thick gypsum board false ceiling including 0.55mm thick GI perimeter channel, GI channel tray frame work having one flange of 20mm and another flange of 30mm with web of 27mm, fixed to surrounding wall using nylon sleeves and screws @ 450 mm centre to centre/GI intermediate channel of size 45mm x 0.90mm thick with two flange of 15mm each suspended from the soffit of roof slab/truss @ 1220mm c/c with MS angle of suitable size fixed to soffit of ceiling with GI cleat and expansion fasteners with and including ceiling section (not exc 1.2 metre length) of 0.55 mm thickness having kurled web of 50 mm and flange of 25 mm ecah with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel @ 457 mm centre to centre with necessary nuts and bolts and gypsum board screwed to ceiling section with stainless steel screws @ 230mm c/c including applying two coats of plastic emulsion paint over a coat of primer to exposed surfaces complete all as specified and as directed. (NOTE: Quoted rate shall be deemed to be inclusive of the cost of ceiling board)

S&F 3mm thick ordinary quality sheet glass and glazing with oil putty in square n.exc. 0.5 Sqm in each pane complete all as directed.

S&F 4mm thick ordinary quality sheet glass and glazing with oil putty in square n.exc. 0.5 Sqm in each pane complete all as directed.

S&F 4mm thick frosted sheet glass and glazing with oil putty in square n.exc. 0.5 Sqm in each pane complete all as directed.

M&L rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc of Fe-410-W(Gde-E-250) quality-B complete all as specified and directed.

M&L non skid ceramic 7 to 8 mm thick coloured tiles, joint free, (square/rectangular) area of each tile exc 0.06 Sqm but n.exc 0.11 Sqm, set and jointed in neat cement slurry and pointed in white cement mixed with pigment as in floor, laid over and including 20 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L non skid ceramic 7 to 8 mm thick coloured tiles, joint free, (square/rectangular) area of each tile exc 0.11 Sqm but n.exc 0.18 Sqm, set and jointed in neat cement slurry and pointed in white cement mixed with pigment as in floor, laid over and including 20 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L glazed coloured ceramic tiles in vertical surface 300 X 450 X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles, laid over and including 10mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M&L glazed coloured ceramic tiles in vertical surface 300 X 200 X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles, laid over and including 10mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

S&F Chromium plated brass Bib cock, long body with wall flange fixed to 15 mm bore of Iron pipe as in repair complete all as specified and directed. (Make : Essco, Cat No: DLX-512 / PRAYAG, Cat No: 7209 / SOMANY, Model: ETHER / JAINKO, Cat No: LNJ-1)

Taking up or down steel water tubing 25 mm bore incl connection etc complete all as specified and directed.

Taking up or down steel water tubing 20 mm bore incl connection etc complete all as specified and directed.

Taking up or down steel water tubing 15 mm bore incl connection etc complete all as specified and directed.

S & F 25mm bore galvanised steel tubing (medium grade) with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed.

S & F 15mm bore galvanised steel tubing (medium grade) with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed.

S & F 20mm bore galvanised steel tubing (medium grade) with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed.

M & L for 6 mm thick asbestos cement, corrugated sheet in roof, wall fixed with L type or J type hook complete all as specified and directed.

M&L for Asbestos cement one piece plain angular ridge 6mm thick, fixed with coach screws complete all as specified and directed.

Supply and fixing 2nd class hard wood plain solid straight chowkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F in repair 35 mm flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F Factory made solid PVC door frame (chowkhat) of size 50mmx47mm made out of 5mm plain colour wood grain PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with printed sheet reinforced with MS square tube, fixed in opening as per specification & drg as per manufacturer instrutions.

S&F Factory Made Solid Panel PVC Door Shutter 30mm thick, consisting of frame made out of Mild Steel Tube of 19 Gauge thickness and size of 19mm x 19mm for Stiles and 15mm x 15mm for Top & Bottom Rails. Mild Steel Frame shall have a coat of Steel Primer of Approved Make and Manufacturer. Mild Steel Frame shall be covered with 5.0mm thick heat moulded PVC 'C' Channel of size 30 x 50mm forming Stiles and 5.0mm thick, 75mm wide PVC Sheets For Top Rail, Lock Rail & Bottom Rail on either side, and 10mm (5.0mm x 2) thick, 20mm wide Cross PVC Sheet as gap insert for Top Rail, Lock Rail & Bottom Rail. Panelling of 5.0mm thick PVC Sheet Beading on either side and joined together with Solvent Cement Adhesive, etc. An additional 5.0mm thick PVC Strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC Solvent Adhesive, fixing in opening as per Specifications and Drawings shown in MES Schedule Part-II, complete all as specified and as directed.

M&L mild steel bands and straps support or stays holdfast and similar articles conforming complete all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, treating ends of posts, back of chowkhats etc, with tar or coal tar black paint, area tarred exc 0.1 sqm but n. exc 0.5 sqm each complete all as specified and directed.

-ditto- but treating small articles such as holdfasts, ends of posts, back of chowkhats, etc, area n exc 0.1 sqm each

Supply and fixing mild steel wind ties for roof including securing bolts complete all as specified. (NOTE: Measurement shall be taken for the ms flat only. Quoted rate is deemed to include for the cost of securing bolts etc)

S&F 300mm long aluminium anodised sliding bolt with hasp, staple (bolt type) and fixing clips or sheets cast of extruded section and fixing bolts and sliding bolts of extruded section ISI marked complete all as specified and directed.

Supply & fixing 100mm mild steel butt hinges (medium weight) cold rolled complete all as specified and directed.

Supply & fixing 150 mm size aluminium anodised barrel tower bolts of extruded section (ISI marked) complete all as specified and directed.

Supply & fixing extruded aluminium alloy handle fabricated type anodised 100 mm size (ISI marked) complete all as specified and directed.

S&F in repairs 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap as in roof, wall fixed with L-type or J- type or crancked hook bolts in lieu screw complete all as specified and directed.

S&F in repair 35mm thick precast cement concrete (1:2:4) type B-0 (using 12.5 mm graded crushed stone aggregate) as in louvers and jallies including all moulding, set in cement mortar 1:4 incl dismantling existing unsv jali complete all as specified and directed.

Dismantling of post struts (wood, steel or RCC) any section incl Taking out embedded portion in concrete and making good disturbed ground complete all as specified and directed.

-ditto- but dismantling of post, struts etc in natural ground

Dismantling fencing wire mesh any type complete all as specified and directed.

Excavation in post holes each not exc 0.5 cum getting out returning filling in and removing earth or broken rubble mixed with earth around in layers not exc 25 cm watering and removing surplus soil to a distance not exc 50m and making good surface as in soft /loose soil complete all as specified and directed.

M&L for PCC 1:3:6 type C2 (using 40 mm graded stone aggregates) as in foundation filling and mass concrete complete all as specified and directed.

S&F mild steel fencing posts and struts including cutting tops to shape as directed drilling holes notching for wire etc flat iron fillets including all necessary drilling bolting or riveting etc and similar work confirming to fe -290 gde E-165 complete all as specified and directed.

Re-fixing of old serviceable mild steel fencing posts and struts including cutting tops to shape as directed drilling holes notching for wire etc flat iron fillets including all necessary drilling bolting or riveting etc and similar work complete all as specified and directed.

S&F 3mm dia PVC Coated galvanised mild steel chain link fencing of mesh size 75x75mm fixed with string bolts including provn of binding wire etc complete all as specified and directed.

S&F 4 mm dia PVC Coated galvanised mild steel chain link fencing of mesh size 75x75mm fixed with string bolts including provn of binding wire etc complete all as specified and directed.

S&F MS round bar for holding chain link fencing nibs etc with fencing posts complete all as specified and directed.

S&F MS Screw bolts (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends each screwed end to the fitted with washers &one hexagonal or square nut exc 5cm n exc 10cm long & 5 to 10mm in dia complete all as specified and directed.

Supply and fixing in repairs galvanized 2 strand steel barbed wire fencing conforming to IS : 278, with 2.24 mm dia. barb wire conforming to IS : 280 with zinc coating as per IS : 4826, barbed with 2 mm dia. barbs at 75 mm spacing and straining and fixing to any type of standard rails/RCC fencing posts straining bolts, including securing or tying at crossing with and fixing of galvanized mild steel wire, staples or steel pins etc., incl dismantling of existing barbed wires complete all as specified and directed. (Note: - Each line of wire will be measured)

Re-straining, resecuring incl making good barbed wire, any type and re-fixing to any type of standard rails/RCC fencing posts straining bolts, including securing or tying at crossing with and fixing of galvanized mild steel wire, staples or steel pins etc complete all as specified and directed. (Note: - Each line of wire will be measured)

M&L for applying one coat of synthetic enamel paint to old decorated steel surfaces of any description not exc 10 cm width or girth including preparation of surfaces all as specified and directed by Engineer-in-Charge.

M&L for applying two coats of synthetic enamel paint over a coat of Red oxide, zinc chrome primer to new steel surfaces of any description not exc 10 cm width or girth including preparation of surfaces all as specified and directed by Engineer-in-Charge.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or froged into spikes framed guard bars, barred iron door ladders framed, blausters walk ways railing, framwork of water railing framework of water tanks and similar work con-forming to Fe 290 Gde -E-165etc complete all as specified and as directed by Engr-in-Charge.

M&L for applying two coats of synthetic enamel paint over a coat of Red oxide, zinc chrome primer to new steel surfaces of any description over 10 cm width or girth including preparation of surfaces all as specified and directed by Engineer-in-Charge.

Supply, hoisting and fixing rotational moulded polyethylene water storage tank (cylindrical vertical type with closed top) of capacity 1000 Litres, multi-layered (ISI marked), with GI tank nipple & cover, hoisted and fixed in position all as specified in SSR Part-I incl dismantling of existing tank complete all as specified and directed.

Supply, hoisting and fixing rotational moulded polyethylene water storage tank (cylindrical vertical type with closed top) of capacity 2000 Litres, multi-layered (ISI marked), with GI tank nipple & cover, hoisted and fixed in position all as specified in SSR Part-I incl dismantling of existing tank complete all as specified and directed.

S&F 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed complete all as specified and directed. (MAKE : PRAYAG, Cat No. 152 or equivalent model in JEXON / POLYTUF / SHAKTI)

S&F in repair 25 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed complete all as specified and directed. (MAKE : PRAYAG, Cat No. 153 or equivalent model in JEXON / POLYTUF / SHAKTI)

Demolition of stone slabs and tiles of any description or thickness in floors/vertical surfaces, etc laid, bedded and pointed in any mortar, etc complete all as specified and directed by Engineer-in-charge.

M&L granite (of any type) work, 18-20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, urinal partition and like in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and making moulds on edges laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

-ditto- but on 20 mm thick screed bed in cement mortar 1:4

M&L for providing precast cement concrete Type B1, 1:2:4 (20mm graded stone aggregate) in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings, kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone wallin) corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat ing etc. and setting in cement mortar 1:4 complete with joints to match complete all as specified and directed.

M&L Sand filling under floors under paver block including watering and consolidation complete all as specified and as directed

Relaying paver block in patches, including removing and cleaning old paver block, preparing beds and laying or setting, jointing new or old paver blocks complete all as specified and as directed. (NOTE: Sand cushioning, if required shall be measured and paid seperately. Replacement of broken paver block shall be paid seperately as "Supply only")

Supply only machine pressed precast concrete interlocking paver block with grey cement and pigmnent of any shape and size as approved by GE conforming to IS-15658-2006 of 60 mm thickness, M-35 grade complete all as specified and directed.

M&L 25 mm thick pre-polished coloured chequered tiles of size 400X400 jointed and pointed in neat cement slurry with white or coloured to match, laid over and including 20 mm thick screed bed in cement mortar 1:6 complete allas specified and directed.

Supply and fixing in repairs concertina coil (reinforced punched barbed tape single layer) for fencing work incl taking down existing coils complete all as per following specifications :- (i) Diameter of concertina coil - 600 mm dia (ii) Number of turns in concertina - 50 to 53 turns (iii) Weight of each coil - 9.5 to 10 KG (iv) Coverage per coil - 6 m (v) Central core wire - made from high tensile spring steel core wire conforming to IS-4454 duly hot dipped galvanised (conforming to IS-2629) with diameter 2.59 mm + 0.05 mm, UTS 145-160 kg/sqmm, zinc coating 250-300 grams/sqm (vi) Strip - Electro galvanised steel strip 0.5 mm + 0.02 mm thick, width 19 mm (before wrapping on central core wire) conforming to IS-1573, zinc coating - 120 gram/sqm and bituminised dipped, width of barbs 11.5 mm, pitch of barbs 25.4 mm+ 0.2 mm (vii) Clips - AISI 304-1.5 mm thick 'C' & 'U' clips. 'C' special type for fixing coil and RBT wire, 'U' clips special type for joining one coil to another coil and RBT wire to RBT wire joining. (viii) No. of clips - 125 for each coil (ix) Handle and spikes to be provided as required (NOTE : Running length of the wall shall be measured for payment purpose).

M&L 75 mm thick PCC 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in sub base of floor/hardstanding etc, finished even and fair complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in plinth protection/Paving etc, finished even and smooth without using extra cement complete all as specified and directed.

M&L 50 mm thick PCC 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in sub base of floor/hardstanding etc, finished even and fair complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade complete all as specified and as directed. (NOTE: Sand cushioning shall be measured and paid seperately)

M&L applying two coat of cement base paint over a coat of alkali resistant primer on newly plastered surfaces of walls including preparation of surfaces.

M&L for 15mm thick rendering in cement mortar (1:4) to fair faces of brick or concrete wall surfaces finished even & smooth without using extra cement complete all as specified and directed.

M&L mild steel work in tubular trusses including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS-1161:2014 grade St-240 complete all as specified and directed.

S&F plates (plain or chequered) channels, square cut or notched (ordninary and counter sunk) forming holes, without any attachment all as specified rolled mild steel in stairs ( framed) including stringers, treades landing, balusters, hand rails etc including cleats, brackets etc complete all as specified and as directed.

S&F stainless steel wire cloth, 0.65mm nominal dia of wire and average width of aparture 1.40mm and fixed with stainless steel wire staples complete all as directed.

Material and labour for applying two coats of exterior acrylic emulsion weather proof paint over a coat of exterior primer to new plastered surfaces of walls of any description, over 10cm width or girth not otherwise described, including preparation of surfaces complete all as specified and as directed.

M&L applying one coat of cement base paint on old decorated plastered surfaces of walls including preparation of surfaces complete all as specified and directed.

M&L applying one coat of acrylic distemper on old decorated plastered surfaces of walls including preparation of surfaces complete all as specified and directed.

S&F in repair Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back or Angle Back Type) with 32mm dia Brass Chromium Plated Waste Fitting, making good disturbed Surfaces in Cement Mortar 1:3 including taking down/out unserviceable Wash Hand Basin and connected Items, complete all as specified and directed. (MAKE : PARRYWARE, Cat No. C0406 / HINDWARE, Cat No. 10010 / JAQUAR, Cat No. CNS-WHT-801 / CERA, Cat No: S2040141)

S&F in repairs chromium plated round grating 100mm dia complete all as specified and directed.

S&F in repair 15 mm bore fancy type stop valves, cast copper alloy, chromium plated (concealed type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and, complete all as specified and directed. (MAKE : ESSCO, Cat No: DLX-514B / PRAYAG, Cat No : PIS-18 / SOMANY, Model: ETHER / JAINKO, Cat No: CSV-1)

S&F in repair Chromium plated brass Angular stop cock concealed type incl concealed body, fixed to 15 mm bore of Iron pipe complete all as specified and directed. (Make : Essco, Cat No: DLX-526 / PRAYAG, Cat No: PR-144 / SOMANY, Model: ETHER / JAINKO, Cat No: AVJ-1)

Supply and Fix in repair vitreous China Squatting pan ‘Orissa’ pattern, size 580 X 440 mm, white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, etc and including making good to floor, complete all as specified and directed. (MAKE : PARRYWARE, Cat No. C0117 / HINDWARE, Cat No. 20004 / JAQUAR, Cat No. CNS-WHT-OP01 / CERA, Model: COVY / SOMANY, Model: SIGNATURE)

M&L for providing PCC (1:2:4) type B-2, using 40 mm graded stone aggregate, as in surface channels and drains including necessary from work complete all as specified and as directed.

M&L for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and directed

M&L for PCC (1:2:4) type-B1 (using 20mm graded crushed stone aggregate) as in coping and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work etc complete all as specified and directed.

S & F RCPC ( Reinforced Cement Polymer Concrete ) grating slab only of size 900 mm x 600 mm x 100 mm thick, of Capacity 5 MT fixed in proper position complete as directed by Engr-in -Charge.

Supply, laying, jointing and testing 300 mm bore RCC pipes, Class NP3 laid & jointed complete all as specified and directed.

Taking down rain water pipe ( any size or pattern ) incl all fittings, heads, shoes, bends, swan necks etc and stacking aside for reuse or removal to store (measured overall as fixed along the centre line over fitting and accessories) complete all as specified and directed.

Dismantling of 100mm dia cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

M&L for cutting chases for water tubing, pinning in making good to facing where required in cement mortar (1:3) to brick wall cutting girth n.exc. 10cm girth complete all as directed.

S&F PVC (SWR) Pipe 110 mm OD, single socketed in any length with rubber ring joints, fixed to walls with necessary clamps complete all as specified and directed.

S&F PVC (SWR) bends for 110 mm OD pipe, any radius complete all as specified and directed.

S&F Cast iron soil, waste and vent pipe, spun pipe 100 mm bore in any length with or without ears with cement joints fixed on walls with FI clamps complete all as specified and directed.

Material and labour of CI plain Bends (any radius), 100 mm bore with duck's foot or heel rest including jointing with cement mortar 1:1 complete all as specified and directed

Material and labour of CI cowl for 100 mm bore pipe complete all as specified and directed.

Material and labour of CI Branch pieces, for 100 mm bore pipe, single (any radius), equal or unequal, ordinary or inverted (spigot or socket type) with parallel branches fitted with oval access door including jointing with cement mortar 1:1 complete all as specified and directed

S&F sinks with drainage board made of stainless steel 1 mm thick in kitchen with plug washers, waste coupling, PVC waste pipe and fixing cantilever brackets connecting union to pipe, overall size of sink 914 mm x 460 mm and bowl size 405 mm x 354 mm x 203 mm complete all as specified and directed. (MAKE : PRAYAG, Cat No. 1239-D or equivalent model in NIRALI / DIAMOND / ANJALI / JAYNA / BLUE STAR / CERA / PARRYWARE)

S&F in repair 15mm bore chromium plated sink cock swivel casted spout (wall mounted model) as directed by Engineer-in-charge (Make : CERA, Model: Garnet (F2002261) / ESS ESS, Model: Primus (PR-114) / JAQUAR, Model: Florentine (FLR-5347N)/ PARRYWARE, Cat No: G3321A1 / PRAYAG, Cat No: 8716)

S&F in repair, 15 mm bore fancy type stop valves, cast copper alloy, chromium plated (concealed type), screwed down, high pressure, with crutch or butterfly handle, incl concealed body, screwed both ends for iron pipe or for unions and, complete all as specified and directed. (MAKE : ESS ESS, Cat No: TM-332 & E221 / CERA, Model: F200351 & F4050102 /JAQUAR, Cat No: FLR-5083NK & ALD-083 / PARRYWARE, Cat No : G0651A1 & G5052A1 / / PRAYAG, Cat No: 9318 & CPS-15/ HINDWARE, Cat No: F280027 & F850096)

S&F CP bottle trap with internal portion 32mm size with 190mm long wall connection pipe complete all as specified and directed (Make: JAQUAR, Cat No: ALD-769L250x190 / ESS ESS, Cat No: C-231 / HINDWARE, Cat No: F850003 / CERA, Cat No: F8060302/ PRAYAG, Cat No: BEA-26)

S&F CP waste coupling, full threaded, for stainless steel sink complete all as specified and directed. (Make: PRAYAG, Cat No: BEA-11 / JAQUAR. Cat No: ALD-705/ CERA, Cat No: F8050101)

Making moulding of granite slab edges cutting grinding incl polishing to reqd shape complete all as specified and directed.

S&F in repair Block boards 18 to 19 mm thick, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work (as in cup board) incl taking down old board complete all as specified and as directed.

S&F Decorative laminate type 1 (0.90 mm thick) of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and as directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flap 30 mm complete all as specified and as directed.

S&F stainless steel handle 150 mm long decorative type complete all as specified and as directed.

S&F cupboard magnets heavy duty complete all as specified and as directed.

M & L brick work using old size sub class 'B' fly-ash bricks straight or curved on plan to any radius in half brick wall, built in cement mortar 1:4 complete all as specified and directed.

M&L RCC Type B1, 1:2:4 (20 mm graded stone aggregate) for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and Chajjas and in shelves and the like complete all as specified and directed. (NOTE: Reinforcement shall be measured seperately)

M&L for Use and waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick surface horizontal or sloping, fair finished surface of concrete complete all as specified and directed.

DGR CONSTRUCTION

MS JYOTI INDUSTRIES

SINHA ENTERPRISE

ARJUN DAS VALECHA

KWALITY CONSTRUCTION

dutta and dutta

M/s Qureshi Construction Co