CA NO GE-AFJ-52-2019-20 SPECIAL REPAIR TO BLDG NO T-12 AND T-13 AT KALUCHAK AND CERTAIN REVENUE AND MINOR WORKS UNDER GE AIR FORCE JAMMU

Amount

Demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness (below or above ground level) and removing demolished material to a distance and depositing to the distance exceeding 50 metres but not exceeding 100 mitres where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed by Engineer-in-Charge.

Demolition of Reinforced Cement Concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for, complete all as specified and as directed by Engineer-in-charge.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, including cutting of trees, shrubs or any type of vegitation upto and including roots complete including removal all debries exceeding 50m but not exceeding 100m all as specified and directed by Engineer-in-Charge.

Dismantling wall & ceiling boards (fibre pulp insulation etc) or insulation boards/ slabs/blankets, any thickness including cover fillets complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tile to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing for 15mm dia pipe and connections including cleaning for re-fixing or removal to store.all as spd and directed by Engg-in-Charge

Taking up or down steel tubing for 20mm dia pipe and connections including cleaning for re-fixing or removal to store.all as spd and directed by Engg-in-Charge

Dismantling timber scantlings 40 sq. cm and over in section, in any position as in unframed work, complete all as specified and as directed by Engineer-in-charge.

Dismantling timber scantlings 40 sq. cm and over in section, in any position as in framed work, complete all as specified and as directed by Engineer-in-charge.

Dismantling timber scantlings under 40 sq. cm in fillets, rails, posts, rafters, purlins, etc, in any position as in framed work, complete all as specified and as directed by Engineer-in-charge.

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings, complete all as specified and as directed by Engineer-in-charge.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed by Engineer-in Charge.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 sqm but not exceeding 4.00 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed by Engineer-in Charge.

Use and waste of form work to sides and sofits of floor or roof beams, beams haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc to obtain rough finished flat surface of concrete complete all as specified and as directed by Engineer-in-charge.

TMT mild steel bars, 8 to 10 mm dia, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed by Engineer-in-charge.

TMT mild steel bars, 10mm dia and over, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed by Engineer-in-charge.

Reinforced cement concrete 1:2:4 (Nominal Mix) type B-1, (using 20 mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and as directed by Engineer-in-charge.

Plain cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregates) as in steps, seismic and other similar bands, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, cills, lintels upto 1.50 metre clear span, copings etc. and in similar works including weathering, slightly rounded or chamfered angles and throating and necessary form works, complete all as specified and as directed by Engineer-in-charge.

20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over and including 15mm thick screed bed or bedding layers of cement mortar 1:6 including finishing the surfaes even and rough complete all as specified and as directed.

20mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, over and including 10mm thick rendering in cement mortar 1:4 including finishing the surface even and fair complete all as specified and directed.

M/L Cement concrete 1:3:6 type C2 using 40mm graded stone crushed aggregate in plinth protection, 50mm thick, finished even and smooth using extra cement, including making joints 6mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 grade and three part of sand (all by weight) complete all as specified and as directed.

All as per ser item No 21.00 here-in-before but 75mm thick as in plinth protection/hardstanding complete all as specified and as directed.

Mild steel rolled sections Fe 410-W (Gde-E- 250) quality B as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and as directed by Engineer-in-charge.

Mild steel Rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails guides for sliding doors, and vertical posts of pipes sections fixed with angle cleats or other connecting plates, Fe-410-W (Gde - E -250), quality B complete all as specified and as directed by Engineer-in-charge.

Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165,complete all as specified and as directed by Engineer-in-charge.

Preparation of new steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of red oxide/zink chrome primer, complete all as specified and as directed by Engineer-in-charge.

Prepainted colored trapezoidal profiled Galvalume/ Zincalume coated steel sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy mettalic coating 550 MPA yield stress as per AS-1397), as in roof covering/cladding to wall fixed with self tapping screws colour/exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, all fixed with Galvanised self drilling/self-tapping fastener (12-14 x 55 with EPDM seals) complete all as specified and directed by Engr-in-Charge Make : Tata Blue Scope Steel Ltd, JSW Steel Ltd, CRIL, Bhushan Steel or equivalent in performance of makes as specified in PS.

Prepainted colored plain profiled Galvalume/ Zincalume coated steel sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy mettalic coating 550 MPA yield stress as per AS-1397), as in roof covering/cladding to wall fixed with self tapping screws colour/exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, all fixed with Galvanised self drilling/self-tapping fastener (12-14 x 55 with EPDM seals) complete all as specified and directed by Engr-in-Charge Make : Tata Blue Scope Steel Ltd, JSW Steel Ltd, CRIL, Bhushan Steel or equivalent in performance of makes as specified in PS.

Pressed steel frames for doors, made out of 1.25 mm thick MS sheet, with one or more rebates including supply and fixing of necessary fixing lugs, hinges, lock strike plate etc. complete, of frame size 125 mm x 60 mm, including one shop coat of red oxide zinc chrome primer, including bottom of each chowkat to be welded with and including 25 x 3 mm thick flat iron projecting 10 cm on either side, applying and including one coat of black paint to prevent from corrosion complete all as specified and as directed by Engr-in-Charge.

Pressed steel frames for doors, made out of 1.25 mm thick MS sheet, with one or more rebates including supply and fixing of necessary fixing lugs, hinges, lock strike plate etc. complete, of frame size 105 mm x 60 mm, including one shop coat of red oxide zinc chrome primer, including bottom of each chowkat to be welded with and including 25 x 3 mm thick flat iron projecting 10 cm on either side, applying and including one coat of black paint to prevent from corrosion complete all as specified and as directed by Engr-in-Charge.

Cutting holes in brick walls built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required Exc. half brick but not exc. one brick complete all as specified and directed by Engineer-in-Charge.

Plain cement concrete 1:3:6 type C-0 using 12.50mm graded crushed stone aggregates as in back filling to pressed steel frame, foundation, filling and mass concrete, complete all as specified and as directed by Engineer-in-charge.

Butt hinges, medium weight, cold rolled mild steel and fixed with screws or with welding to existing MS/PVC frames, 100 mm size, ISI marked, complete all as specified and directed by Engineer-in- Charge.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform,and other similar situations complete all as specified and directed by Engineer-in-Charge.

S&F for factory made 35mm thick 2nd class hard wood Plain, framed, panelled shutters, with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces.The size of rail and stile as per IS:1003 (Part-I), kiln seasoned and chemically pressure treatedmedium density, wood particle board with commercial face veneers fitted to chowkhat complete all as specified and as directed by Engineer-in-Charge.

S&F for factory made 35mm thick 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass/gauge etc divided into squares, with plain , chamfered or rounded, mitred and rebated sash bars, any numbers edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of door shutters as specified in SSR Part-I sec 8 clause 8.20 (a), fixed to chowkhat all as specified and as directed by Engineer-in-Charge.

M&L for factory made steel windows conforming to IS-1038 with side hung shutters including box type hinges with 02 nos MS 100mm size barrel tower bolt for each leaf and Z section handle and steel peg stay complete with glazing bars, dovetailed or welded including one shop coat of Red Oxide Zinc chromate primer complete all as specified and directed by Engineer-in-Charge.(Note :- Glass panes shall be measured and paid for separately).

M&L for factory made steel windows conforming to IS-1038 with side hung shutters including box type hinges with steel handle and steel peg stay complete without glazing bars, dovetailed or welded including one shop coat of Red Oxide Zinc chromate primer complete all as specified and directed by Engineer-in-Charge. (Note :- Wire gauge shall be measured and paid for separately).

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar, barred iron doors; ladder, framed balusters; railing; frame work for water tanks, cooler stand etc and similar work conforming to FE 410-O or 310-O, fixed in repairs complete all as specified and as directed by Engineer-in-charge.

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar, barred iron doors; ladder, framed balusters; railing; frame work for water tanks, cooler stand etc and similar work conforming to FE 410-O or 310-O, complete all as specified and as directed by Engineer-in-charge.

3mm thick Sheet glass, ordinary quality and glazing with oil putty in square or rectangle, area n exc 0.5 sqm in each pane complete all as specified and as directed by Engineer-in-charge.

4mm thick Sheet glass, ordinary quality and glazing with oil putty in square or rectangle, area n exc 0.5 sqm in each pane complete all as specified and as directed by Engineer-in-charge.

S&F Galvanised mild steel wire cloth 0.56mm nominal dia wire and average width of aperture 1.18mm and fixed with tinned tacks of galvanised wire staple to steel windows/fixed with wooden beads of 2nd class HW to wooden doors/windows complete all as specified and directed.

S&F for Aluminium alloy, anodised, sliding door bolt 250mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F for Aluminium alloy, anodised, sliding door bolt 300mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F for Aluminum, anodized, barrel tower bolts of extruded section 150 mm long, complete all as specified and directed.

S&F for Aluminum, anodized, barrel tower bolts of extruded section 200 mm long, complete all as specified and directed.

S&F for Extruded aluminum alloy handle, fabricated type, anodized 125mm size, complete all as specified and directed.

300mm, mild steel helical door spring including roller and roller plate completecomplete all as specified and as directed by Engineer-in-charge.

S&F for Floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel fixed in floor with over all length of cover plate 140 mm, complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:4:8 type D2 (40mm graded crushed stone aggregate) as in sub base of flooring complete all as specified and as directed by Engr-In-Charge.

M&L for 100 mm thick plain cement concrete 1:4:8 type D2 (40mm graded crushed stone aggregate) as in flooring including finishing the surfaces even and smooth complete all as specified and as directed by Engr-In-Charge.

25 mm thick, Plain cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in sub base for laying floor finishes including finishing the surfaces even and rough without using extra cement, complete all as specified and as directed by Engr-in-Charge.

Brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, complete all as specified and as directed by Engr-in-Charge.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on walls in cement mortar 1:6, complete all as specified and directed by Engr-in-charge.

Rendering 15 mm thick on other than fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on walls in cement mortar 1:4, including mxed with liquid water proofing admixture complete all as specified and directed by Engr-in-charge. Note: Liquid water proofing admixture shall be measured and paid seperately as "Supply only" under relevant item of this BOQ.

Supply only Liquid Water Proofing admixture complete all as specified and directed by Engr-in-charge.

Preparing plastered or unplastered new surfaces of walls and applying two coat of oil emulsion distemper over a coat of chalk whiting, complete all as specified and as directed by Engineer-in-charge.

Preparation of newly plastered or undecorated surfaces of wall and applying two coats of cement base paint including curing before and after applying each coat complete all as specified.

Preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Preparation of old decorated or previously treated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

Supply and fixing anodized aluminium snap grid frame work of grid size 605 x 605mm for flase ceiling, fixed to surrounding wall and hanger 6mm dia Gi (upto 1200mm length) adjusting level fixed to roof with GI flat 40 x 3mm size 60mm long and expansion hold fasteners, including 4mm thick non asbestos fibre cement building boars inserted to snap grid frame work and providing three coats of white wash as in ceiling complete all as specified and as directed by Engr-in- Charge.

Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab in floor including rubbing and polishing, laid over and including 20mm thick bedding layer in cement mortar 1:4 including finishing the surfaces even and rough complete, all as specified and as directed by Engineer-in-charge.

Machine cut kota stone 15mm thick as in riser of steps, skirting, dado and pillar laid over cement screed base and jointed with white cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, over and including 10mm thick rendering in cement mortar 1:4 on brick masonry walls complete all as specified and as directed by Engineer-in-charge..

Joint free non skid ceramic coloured tiles 7 to 8mm thick (sqaure/rectangular) area of each tiles exc.0.11 Sqm but n. exc. 0.18 Sqm as per IS-13755 in floor, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including screed bed 15mm thick in cement mortar 1:6 complete as directed by EIC.

Joint free non skid ceramic coloured tiles 7 to 8mm thick (sqaure/rectangular) area of each tiles exc.0.11 Sqm but n. exc. 0.18 Sqm as per IS-13755 on vertical surfaces such as skirting /dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 10mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces as backing coat complete all as specified and directed by Engineer-in-Charge.

Glazed ceramic coloured tiles as per IS-13753, 350mm x 250 mm x 7 mm thick/450mm x 350mm x 7mm thick on vertical surfaces such as skirting /dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 10mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces as backing coat complete all as specified and directed by Engineer-in-Charge.

M&L for 20 mm thick interlocking machine pressed precast concrete interlocking paver block any shape, any colour and rubber finished type confirming to IS 15658-2006, M-35 grade laid and jointed in neat cement slurry with grey cement and pigment, laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:4 including finishing the surace even and rough complete all as specified and directed.

M&L for 80 mm thick interlocking machine pressed precast concrete interlocking paver block any shape, any colour and rubber finished type confirming to IS 15658-2006, M-40 grade laid and jointed in neat cement slurry with grey cement and pigment laid over 50 mm thick sand cushioning complete all as specified and directed.

M&L for 15mm dia bore galvanized steel water tubing, “medium grade,” together with all fittings; (ISI marked) such as elbows, bends tees, nipples, union sockets, sockets etc and short pieces and fixed complete to walls and ceilings or laid in floors complete all as specified.

M&L for 20mm dia bore galvanized steel water tubing, “medium grade,” together with all fittings; (ISI marked) such as elbows, bends tees, nipples, union sockets, sockets etc and short pieces and fixed complete to walls and ceilings or laid in floors complete all as specified and dirceted.

Stainless steel sink, with drainage board, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm fixed in repairs complete all as specified and as directed.

Supply and fixing in repairs 15mm dia bib tap, fancy type, cast copper alloy with crutch or butter fly handle screwed down screwed for Iron Pipe or brass ferrule and fixed complete all as specified and dirceted.

Gun-metal, globe or gate valves, ISI marked, with iron wheel head, screwed both ends for iron pipe of size 20mm, fixed in repiars, complete all as specified and as directed by Engr-in-Charge

Viterous china wash basin, white flat back size 580 x 450mm including waste coupling CP 32mm dia and CI brackets of iron 65 x 65 x 6mm embedded in PCC block with PCC 1:2:4 type B-1 and PVC waste pipe 32mm dia & CP grating with holes complete, fixed in repairs, all as specified and as directed by Engr-in-Charge.

15mm bore pillar tap cast copper alloy chromium plated screwed downhigh pressure, with or without lettered 'hot or cold' with long screwed shanks and fly-nuts screwed for iron pipe, complete fixed in repairs, all as specified and directed by Engineer-in-Charge.

S&F in repairs cast copper alloy 15mm dia stop cock screwed down high pressure with crutch or butter fly handles screwed both and iron pipe or for unions and fixed complete all as specified and dirceted.

Supply and fixing in repairs Angle valve cast copper alloy cromium Plated (CP) 15mm dia screwed down high pressure with crutch or butter fly handles screwed both and iron pipe or for unions and fixed complete all as specified and dirceted.

Supply and fixing PVC low density waste pipe 32mm bore of standard length with cup and washers for urinal/WHB, fixed in repairs, complete all as specified and as directed by Engr-in-Charge.

PVC connections 15 mm size with PTMT nuts of length 450 mm, fixed in repairs complete all as specified and diected by Engr-in-charge. Make: Prayag/Polytuf/Supreme

S&F for 20mm dia brass chromium plated tubular towel rails,D type, 60cm long between flanges, complete all as specified and directed.

110mm bore, PVC (SWR) pipes, pressure rating 4 kg/sqcm, single or double socketed, in any length with rubber ring joints, fixed to wall with clamps, complete all as specified and as directed by Engr-in- Charge.

S&F PVC (SWR) bends / shoe any radius provided with access door of 110mm dia complete all as specified and directed.

Cast iron soil, waste and vent pipes (Sand cast pipes) in any length with or without ears, with cement joints, laid in trenches or in floors of 75mm bore, complete all as specified and as directed by Engineer-in-charge.

Cast iron soil, waste and vent pipes (Sand cast pipes) in any length with or without ears, with cement joints fixed to wall of 75mm bore, complete all as specified and as directed by Engineer-in-charge.

Cast Iron floor trap with dia of outlet 75mm with CI grating including jointing to waste pipe fixed in cement concrete PCC 1:2:4 type B-1( using 20 mm graded crushed stone aggregate ), complete all as specified and as directed by Engineer-in-charge.

S&F in repairs CP grating 125mm dia as suitable to existing trap as per requirement all as spd and directed by Engg-in-Charge

S&F for MS PVC sheathed 20mm dia drapery rod of approved pattern and shade fixed in repair complete all as specified and as directed.

S&F for end balls made in conical surface and coated with brown/cherry/Golden colour dia of ball not less than 50mm and suitable for curtain rod of 20mm dia fixed in repair complete all as specified and as directed.

S&F for rounded block made in round shape and coated with brown/cherry/Golden colour suitable for curtain rod 20mm dia fixed in repair complete all as specified and as directed.

Rotational moulded polyethylene water storage tank, inner and out white, two layers, ISI marked (cylinderical vertical with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 1000 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes, including taking down of old broken water tank complete all as specified and as directed by Engr-in-Charge.

S&F 20mm dia ball Valve high pressure of PTMT with PVC float and fly nut complete screwed for iron pipe or brass ferrule and fixed complete all as specified and dirceted.

Excavation in trenches in in any type of soil n.exc 1.5m wide and n.exc 1.5m depth in foundations etc for laying of pipe line, manholes, sewage line and getting out complete all as specifed and as directed by Engineer-in-Charge.

Returning filling in (soil) including spreading, levelling, watering and well ramming in layers n.exc 25cm thick in any type of soil complete all as specifed and as directed by Engineer-in-Charge.

Removal of excavated material (soil) to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specifed and as directed by Engineer-in-Charge.

Material and labour for cutting the existing GI pipe 50/100mm dia main water pipe line, inserting and including ISI marked TEE of suitable size 50 x 50 x 25mm for taking connection to OH PVC 1000 litres water storage tank for water supply to building including one union complete all as specified and as directed by Engr-in-Charge.

M&L for 25mm dia bore galvanized steel water tubing, “medium grade,” together with all fittings; (ISI marked) such as elbows, bends tees, nipples, union sockets, sockets etc and short pieces and fixed complete to walls and ceilings or laid in floors complete including taking down old broken pipe all as specified and dirceted.

Supply and fixing fixed in repairs cast copper alloy 25mm dia stop cock screwed down high pressure with crutch or butter fly handles screwed both and iron pipe or for unions and fixed complete all as specified and dirceted.

Plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in foundation, filling and mass concrete, complete all as specified and as directed by Engineer-in-charge.

Reinforced cement concrete 1:2:4 (Nominal Mix) type B-1, (using 20 mm graded crushed stone aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed by Engineer-in-charge.

Use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough flat finished surfaces complete all as specified and as directed.

Reinforced cement concrete 1:2:4 (Nominal Mix) type B-1, (using 20 mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed by Engineer-in-charge.

Mild steel Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. Within 20mm of the length indicated) conforming to Fe 410-W (Gde-E- 250) quality-A complete all as specified and as directed by Engineer-in-charge.

Filling under floors, spreading, levelling, well ramming including watering in layers not exceeding 25cm thick complete all as specified and as directed by Engineer-in-Charge.

Rendering 10 mm thick on fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on walls in cement mortar 1:6, complete all as specified and directed by Engr-in-charge.

M&L for three coats of white washing on new undecorated plastered surface including preparation of walls surfaces complete all as specified.

M&L for two coats of white washing on old decorated plastered surface including preparation of walls surfaces complete all as specified.

TMT mild steel bars, 5mm dia and over upto and including 10mm dia, as in stirrups, spacers & binders, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed by Engineer-in-charge.

Rotational moulded polyethylene water storage tank, inner and out white, two layers, ISI marked (cylinderical vertical with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 1000 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes, complete all as specified and as directed by Engr-in-Charge.

S&F for 20mm dia aluminium chromium plated tubular towel rails,D type,60cm long between flanges, complete all as specified and directed.

Vitreous china water closet, 'Orissa' pattern, including lime concrete bedding, size 580 x 440 mm white with integral foot rests excluding flushing cistern and flush pipe but including connection to trap, anti syphonage pipe etc. complete all as specified and as directed by Engr-in-Charge. Make: Cera/Hindware/Parryware

10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with twin flush provision, complete all as specified and as directed by Engr-in-Charge. MAKE: Cera Model Combiflush twin flush as per Cat Part No. B1020101 (Old Cat Part No 2603) or equivalent in performance of makes as specified in PS.

Supply and fixing 15mm dia stop cock chromium plated, fancy type cast copper alloy screwed down high pressure with crutch or butter fly handles screwed both and iron pipe or for unions and fixed complete all as specified and dirceted.

Supply and fixing 15mm dia bib tap, fancy type, cast copper alloy with crutch or butter fly handle screwed down screwed for Iron Pipe or brass ferrule and fixed complete all as specified and dirceted.

15mm bore pillar tap cast copper alloy chromium plated screwed downhigh pressure, with or without lettered 'hot or cold' with long screwed shanks and fly-nuts screwed for iron pipe, complete, all as specified and directed by Engineer-in-Charge.

Viterous china wash basin, white flat back size 580 x 450mm including waste coupling CP 32mm dia and CI brackets of iron 65 x 65 x 6mm embedded in PCC block with PCC 1:2:4 type B-1 and PVC waste pipe 32mm dia & CP grating with holes complete, all as specified and as directed by Engr-in-Charge.

Vitreous china urinal flat back 465 x 355 x 265mm size (minimum), white including grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe), Connection to flushing pipe and outgoing pipe complete all as specified and directed.

Supply and fixing PVC low density waste pipe 32mm bore of standard length with cup and washers for urinal/WHB, complete all as specified and as directed by Engr-in-Charge.

Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms), complete all as specified and directed by Engineer-in-charge. Make: Prayag/Polytuf/Supreme

S/F for Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S/F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed.

Factory made mild steel ventilators (box type) with upper top hung shutters and bottom fixed type shutters including pintol hinges, steel peg stay and one shop coat of red oxide primer complete all specified.

S&F for 3.00mm thick figured type pin headed glass sheet ordinary quality and glazing with oil putty/ wooden beads with nails in square n.exe 0.5 Square metre in each pane etc complete all as specified and directed.

Butt hinges, medium weight, cold rolled mild steel and fixed with screws or with welding to existing MS/PVC frames, 75 mm size, ISI marked, complete all as specified and directed by Engineer-in- Charge.

S&F for Extruded aluminum alloy handle, fabricated type, anodized 150mm size, complete all as specified and directed.

PVC connections 15 mm size with PTMT nuts of length 450 mm, complete all as specified and diected by Engr-in-charge. Make: Prayag/Polytuf/Supreme

Cast Iron 'P' or 'S' trap for 100mm fixed in cement concrete PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate ), complete all as specified and as directed by Engineer-in-charge.

110mm bore, PVC (SWR) pipes, pressure rating 4 kg/sqcm, single or double socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engr-in- Charge.

Brass Chromium plated over head shower rose with swivel joints, any size, including 190mm long arm fixed to pipe or union of 15mm bore, complete all as specified and as directed by Engr-in-Charge.

Brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4, complete all as specified and as directed by Engr-in-Charge.

Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortor 1:4, complete all as specified and as direceted by Engineer-in-charge.

Use and waste of form work to sides of pillars, posts, struts, piers, columns and stanchions etc, square, ractangular or polygonal, to obtain rough finished surface of flat concrete complete all as specified and as directed.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc to obtain rough finished flat surface of concrete complete all as specified and as directed by Engineer-in-charge.

Reinforced cement concrete 1:2:4 (Nominal Mix) type B-1, (using 20 mm graded crushed stone aggregate) as in columns, pillars, piers, posts and struts complete all as specified and as directed by Engineer-in-charge.

Reinforced cement concrete 1:2:4 (Nominal Mix) type B-1, (using 20 mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and as directed by Engineer-in-charge.

S&F for Aluminum, anodized, barrel tower bolts of extruded section 125 mm long,complete all as specified and directed.

5mm thick rendering on brick or concrete surfaces as in ceiling in cement mortar 1:3, and finish the surface even and smooth without using extra cement, complete all as specified and as directed by Engineer-in-charge.

M&L for coloured vitrifired ceramic tiles light shade tiles 10 mm thick, area of each tile n exc 0.36 Square metre in floors etc set and jointed in neat cement slurry and pointed in colored cement to match Shade, pattern, laying etc of tiles, laid over and including 15mm thick screed bed or bedding layer in cment mortar 1:6 including finishing the surfaces even and rough for receiving floor tiles complete all as specfied and directed.

M&L for coloured vitrifired ceramic tiles light shade tiles 10 mm thick, area of each tile n exc 0.36 Square metre as in vertical surfaces such as dado/skirting and the like, set and jointed in neat cement slurry and pointed in colored cement to match Shade, pattern, laying etc of tiles, fixed over and including 10mm thick rendering in cement mortar 1:4 including finishing the surfaces even and rough for fixing wall tiles complete all as specfied and directed.

Vitreous China coloured wash down water closet pan and seat cover (pedestal pattern), white (excluding flushing cistern and flush pipe) but including connection to drain and flush pipe, including fixing bolts, white/coloured plastic seat cover, CP brass jet nozzle with 900 mm long PVC pipe complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 15mm bore center hole basin mixer with regular spout with pop up waste assembly with 10mm dia 450mm long braided hoses and brass nuts, fixed in repairs, complete all as specified and as directed by Engr-in-Charge. Make : Jaquar Cat Part No CON-167KNB or equivalent of Marc/Kohler

600 mm x 450 mm bevelled edge mirror of thickness 5/5.5mm of slected quality glass with 400mm wide PVC frame of approoved size and colour alround, mounted on 6 mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete, fixed in repairs all as specified and as directed by Engineer-in-charge.

75mm bore, PVC (SWR) pipes, pressure rating 4 kg/sqcm, single or double socketed, in any length with rubber ring joints, fixed to wall with clamps, complete all as specified and as directed by Engr-in- Charge.

S&F PVC (SWR) bends / shoe any radius of 110mm dia complete all as specified and directed.

S&F PVC (SWR) bends / shoe any radius of 75mm dia complete all as specified and directed.

PVC (SWR) vent cowl, 75mm bore, complete all as specified and as directed by Engineer-in-charge.

PVC (SWR) floor trap, 75mm diameter of outlet, plain with grating including jointing with solvent cement, complete all as specified and as directed by Engineer-in-charge.

M&L for three coats of white washing on new undecorated plastered ceiling surface including preparation of surfaces complete all as specified.

Supply and fixing Salt glazed stoneware (SGSW) grade 'A' drain pipes 150mm bore laid and jointed on concrete bed, complete including testing etc all as specified and shown on drgs (concrete bed shall be measured and paid for separately).

Material and labour for Concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D-2 for 150mm bore pipes complete all as specifed and as directed by Engineer-in-Charge.

Rotational moulded polyethylene water storage tank, inner and out white, two layers, ISI marked (cylinderical vertical with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 500 litres each including all accessories (i.e GI nipples), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes, complete all as specified and as directed by Engr-in-Charge.

Mild steel brackets, 150mm, PVC coated, made in shape and size to hold curtain rods, complete all as specified and directed by Engineer-in-Charge. (Colour and pattern shall be as approved by Engineer-in-Charge and GE)

Supply and fixing aluminium pe set of three powder coated as approved by GE complete all as specified and directed.

Supply and fixing stainless steel fancy type, soap dish, fixed to plugs with chromium plated brass screws complete all as specified and directed.

Stainless steel sink, with drainage board, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

Brass chromium plated toilet paper holder complete all as specified and as directed by Engineer-in-charge. Make : Jaquar Cat part No ACN1151N or equivalent of makes specified in PS.

Aluminium frame powder coating of natural anodized aluminium section having minimum thickness 1.50mm, of size 101.60 x 44.45mm including necessary jointing cleats and fixing frame to wall/floor complete in all respect all as per manufacturer's instructions and including making good disturbed surfaces complete all as specified and as directed by Engineer-in-Charge. (Aluminium frame will be provided with/without groves & to accommodate glass, grill etc as per site requirement).

Supply and fixing aluminium doors shutters powder coating air tight with natural anodizing partly glazed with and including 5mm thick tinted glass and partly panel with and including 12mm thick prelaminated particle board (All aluminium member-top, bottom, vertical and middle of shutter made of size 82.55 x 44.45 x 1.50mm thick (minimum) including necessary cleats, glazing clips, 5mm thick tinted glass, one hydraulic door closer( aluminium body, extruded section, regulated, designation No 3, suitable for door shutter of 701 to 1000mm in width and of weight between 61 to 80 kg), rubber packing with anodised aluminium beading/glazing clips size 19 x 17.30 x 0.70mm weight 0.097 kg/RM of both side and fixing aluminium fitting i.e 03 Nos. 100 SS hinge, 02 Numbers 200mm SS handle, 02 numbers 150mm aluminium tower bolts, 01 number brass mortice lock, verticle type of 4 lever complete all as specified and as directed by Engineer-in-Charge. Note: All aluminium members and fittings should be of approved make and ISI marked complete in all respect as per manufacturer's instructions and as directed by Engineer-in-Charge.

Supply and fixing aluminum Sliding three track Glazed and wire gauge Window ( Double glazed & single Wire gauge leaf ) natural anodized section (Bombay Sliding). Aluminum member/section of shutter/leafs made of size 40mm x 20mm x 1.60mm thick including 'U' Channel and Aluminum grill of 6mm dia wire mesh aperture n .exc 50mm fixed to frame including necessary channel /sliding arrangement, jointing cleats, glazing clips, 5mm thick tinted glass, rubber packing with anodized aluminum beading/glazing clip size 19.00 X 17.30 X 0.70mm wt 0.097 Kg/RM of both side and fixing aluminum fitting i.e. handle and locking arrangement cleat type suitable to shutter complete, tower bolts 100mm two numbers in each leaf (Rate shall include for Glass 5mm thick and MS galvanised wire cloth of 0.56 mm dia wire with 1.18mm aperature duly painted with aluminum paint & all fitting should be ISI marked ) complete in all respect as per manufacture instructions and as directed by Engr-In-Chrage . Make :- Hindalco/ Indalco/Jindal all as specified and as directed by Engineer-in-Charge.

Supply and fixing 7.50mm thick aluminium grill Cat part No AL-102 of specifications having aperture length wise 80mm and width wise 66mm with F Channel section complete all as specified and as directed by Engineer-in-Charge.

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in any type of soil, complete all as specified and as directed by Engineer-in-charge.

Preparation of newly plastered surfaces of walls and applying two coats of exterior emulsion paint of Make Apex (Asian) in any tint, over a coat of water based wall primer (as per manufacturer's instruction of Apex) over and including one coat 1.20mm thick Birla white wall care putty, complete all as per manufacturer's instructions all as specified and directed by Engr-in-charge.

Cutting openings, through brick walls (built in cement or cement lime mortar) for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.. to store and rubbish not exc. 50m complete all as specified and as directed by Engineer-in-Charge.

Cutting opening in cement concrete walls (any descript-ion) for door, window and other openings (with or without reinforcement) (with or without reveals) or enlarging existing openings, including trimming surfaces to receive rendering, etc. removing surplus rubbish not exc. 50m complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing Anodised aluminum alloy powder coated standard hollow section for door including aluminum frame/chowkhat with following specification including 12mm prelaminated particle board interior grade both side laminated/12mm thick PVC hollow sheet, or 05 thick tinted glass, anodized aluminum snap beading, glazing clips, joining cleats, rubber gasket screws, 2 Nos aluminum anodized handles (150mm size) in each door etc and other accessories complete all as specified and directed. (a) Door frame of section :- 101.60mm x 44.45mm x 2mm with necessary hold fasts/fastners and connected accessories (b) Bottom, middle and top rail of section :- 100mm x 44.45mm x 2 mm. (c) Stiles of section :- 85mm x 44.45mm x 2mm

Supply and fixing Anodised aluminum alloy powder coated standard hollow section for wndow two tracks including aluminum frame/chowkhat with following specification including 05 thick tinted glass, anodized aluminum snap beading, glazing clips, joining cleats, rubber gasket screws, etc and other accessories complete all as specified and directed. (a) Window frame of section :- 83.50mm x 44.45mm x 1.6mm with necessary hold fasts/fastners and connected accessories (b) Sliding window section (Channel) :- 61.85mm x 31.75mm x 1.2 mm. (c) Sliding shutters of section :- 40mm x 18mm x 1.2mm thickness with locking arrangement NOTE for item No 157.00 and 158.00: 1. The rates quoted by the tenderer shall also include the cost of cutting, waste and making good disturbed surface to match with the existing surface and finishes complete all as directed by Engineer-in-Charge. 2. All aluminium sections used in the work shall of powder coated with minimum thick of 50 micron 3. Mmake of PVC sheet: Syntex/TATA/Rajshree

Supply and fixing Welded steel wire fabric, weight not exceeding 4.00 kg per square metre supplied and fixed complete to wood or welded to steel members complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 125mm hasp & staple safety type of aluminum with mild steel hinge including bolt to hinge plate and fixed with screw complete all as specified and directed.

Cutting holes into or through brick walls built in cement mortar or cement lime mortar and stone walls built in lime mortar or walls of lime concrete. and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required, superficial area exceeding 150 sqcm but not exceeding 400 sqcm complete all as specified and as directed by Engineer-in-Charge.

Mild Steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, conforming to Fe 410-W (Gde-E- 250) quality-A, complete all as specified and as directed by Engineer-in-charge.

Broken stone hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface, complete all as specified and as directed by Engineer-in-charge

Fe 410-W (Gde-E- 250) qualiy B, rolled mild steel sections as in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment, etc. complete all as specified and as directed by Engineer-in-charge.

Mild steel bolts machine made with hexagonal or square head one end each screwed other end to be fitted with washers and one hexagonal or square nut, exceeding 30cm long and dia of neck exc. 11 mm but n. exc. 15mm complete all as specified and as directed by Engineer-in-Charge.

Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and as directed by Engineer-in-Charge.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out in hard/dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and as directed by Engineer-in-Charge.

Taking down carefully copper/aluminium point wiring (light, fan,bell, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc . credit for above items should be made as per conditions separately.

Point wiring concealed with 1.5 Sqmm copper conductor cable (multistrand) PVC insulated FRLS (unsheathed), drawing in and including PVC conduit 20 mm dia, cutting chases wall & ceiling and making good to disrurbed surface of wall, ceiling etc,having wall thickness not less than 2 mm with sunk cast iron/pressed GI modular boxes in wall of required size and colour for mounting modular switches, sockets, regulators etc), including 1.5 Sqmm PVC insulated green insulation (multistranded) FRLS copper conductor continuous earth wire for one light/fan/bell point controlled by one switch one way complete all as specified and directed.

All as per item No. 165 above but for one multipin 5 amps socket outlet on independent board complete all as specified and as directed by Engineer-in-Charge.

All as per item No. 165.00 above but with 2.5 sqmm cable and 1.5 sqmm for earth continuity for multipin 15 amps socket outlet flush type on independent board complete all as specified and as directed by Engineer-in-Charge.

NOTE FOR POINT WIRING ITEMS On RCC roof/ceiling PVC conduit shall be provided on surface with proper fixing clips all as directed by Engineer-in-Charge.

Supply and fixing switch piano button flush type, single pole one way 5 amps complete all as specified and directed by Engineer-in-Charge.

Supply and fixng 5 pin switch socket combination 2 in 1, 5 amps flush type complete all as specified and as directed by Enggineer-in-Charge.

Supply and fixing switch socket combination 5 in 1, 5 and 15 Amp flush type complete all as specified and as directted by Engineer-in-Charge.

Supply and fixing ceiling rose, 3 phase on PVC square blocks surface bakelite 65 x 50 mm, 3 terminal complete all as specified and as directed by Engineer-in-Charge

Supply and fixing stepped electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd complete all as specified and directed.

Supply and fixing MCB SP 5 to 32 Amps, 230 V A/C complete all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4085 87 to 4085 95 of Legrand (DX³) or equal approved in Schneider (Acti -9)/ Siemens (Betagard-5SL4)

Supply and fixing MCB SPN 6 to 32 Amps, 230 V,AC complete all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4086 09 to 4086 17 of Legrand (DX³) or equal approved in Schneider (Acti -9)/ Siemens (Betagard-5SL4)

M&L for concealed sub main wiring with two run of 4.00 sqmm single core multi stranded PVC insulated and unsheathed copper conductor (red for phase and black for neutral) of grade 1100 volt FRLS cable in and including electrical grade PVC conduits of desired colour not less than1.2 mm thick and of 25 mm dia & 2.50 sqmm copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth dolly complete including taking down old submain wiring all as specified and as directed. Make of wire-- Finolex/Havells/Plaza.

M&L for concealed sub main wiring with two run of 6.00 sqmm single core multi stranded PVC insulated and unsheathed copper conductor (red for phase and black for neutral) of grade 1100 volt FRLS cable in and including electrical grade PVC conduits of desired colour not less than1.2 mm thick and of 25 mm dia & 4.00 sqmm copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth dolly complete including taking down old submain wiring all as specified and as directed. Make of wire-- Finolex/Havells/Plaza.

Supply and fixing MCB distribution board Double door SPN 230 volts 8 way with 200 amps rated bus bar concealed to wall and making flush with wall surfaces and making good to disturbed surfaces of walls to match with the exisiting surface etc. Make: Cat part No 5076 11 of Legrand (Ekinoxe) or equal approved in Schneider (Acti-9)/Siemens (Betagard-8GB32)

Supply and fixing MCB distribution board Double door SPN 230 volts 2 way with 200 amps rated bus bar concealed to wall and making flush with wall surfaces and making good to disturbed surfaces of walls to match with the exisiting surface etc. Make: Legrand (Ekinoxe) or equal approved in Schneider (Acti-9)/Siemens (Betagard-8GB32)

Supply and fixing energy saving recessed/surface mounted LED batten T-8 Tara-M tube light fitting of 20 watt 4 feet LED retrofit T-8 tube complete with powder coated decorative patti with tube rod and all other accessories including connecting electrically to ceiling rose using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm complete all as specified and as directed by Engineer-in-Charge. Note :(i) A certificate from the manufactures for warranty minimum upto 3 years shall be obtained and submitted to the AGE/GE (ii) Any touch up of the existing surface due to changing of fittings shall be done by contractor with similar surface finish without extra cost to the department. MAKE: Cat part No LTDC012 20 W LED/WD 20W of C&S or equal approved in Havells/CG

Supply and fixing LED slim ceiling light fitting with extruded aluminium housing and milky diffuser 36 W 2'x2' slim panel 610 x 610mm recessed/suspended/surface mounting and testingwith all other accessories including connecting electrically to ceiling rose using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm complete all as specified and as directed by Engineer-in-Charge. Note :(i) A certificate from the manufactures for warranty minimum upto 3 years shall be obtained and submitted to the AGE/GE (ii) Any touch up of the existing surface due to changing of fittings shall be done by contractor with similar surface finish without extra cost to the department. MAKE: Cat part No LTCRSM36WATT2x2 of C&S or equal approved in Havells/CG

Ceiling fan 5 star rated (as per BEE recommendation) 1200 mm sweep single phase 230 volts, 50 Hz AC supply totally enclosed heavy duty motor with die cast aluminium rotor complete with down rod, including hanging of fan, connecting electrically using 3 core 0.75 sqmm PVC insulated flexible copper conductor cable overall sheathed, fixed in repairs, complete all as specified and as directed by Engineer-in-Charge. MAKE: Havells cat part No ES-50 preimium or equal approved in CG/Bajaj NOTE: Old ceiling fan obtained from site shall be deposited to MES store yard and to be taken on charge by the department

Exhaust fan (iron/steel body), 450mm sweep, ISI marked, 5 star rated, heavy duty AC single phase, 230/240 volts, 50 Hz, 900 RPM, with louvers shutters including cutting holes of suitable size in brick/stone walls for fixing the exhaust fan including making good the disturbed surface to match with the existing finishes, fixed in repairs complete all as specified and directed by Engineer-in- Charge. Make: Cat part No Turbo force SP of Havells or equal approved make in CG/Bajaj. NOTE: Old exhaust fan obtained from site shall be deposited to MES store yard and to be taken on charge by the department

Exhaust fan (iron/steel body), 450mm sweep, ISI marked, 5 star rated, heavy duty AC single phase, 230/240 volts, 50 Hz, 900 RPM, with louvers shutters including cutting holes of suitable size in brick/stone walls for fixing the exhaust fan including making good the disturbed surface to match with the existing finishes, complete all as specified and directed by Engineer-in- Charge. Make: Cat part No Turbo force SP of Havells or equal approved make in CG/Bajaj.

Exhaust fan (iron/steel body), 300mm sweep, ISI marked, 5 star rated, heavy duty AC single phase, 230/240 volts, 50 Hz, 900 RPM, with louvers shutters including cutting holes of suitable size in brick/stone walls for fixing the exhaust fan including making good the disturbed surface to match with the existing finishes, complete all as specified and directed by Engineer-in- Charge. Make: Cat part No Turbo force SP of Havells or equal approved make in CG/Bajaj.

Supply and laying & testing UG cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (Heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70 sq mm, 3.5 core, including taking down old cable complete all as specified and directed by Engr-in-Charge.

Supply and installation hi wall split air conditioner having indoor and outdoor unit and with inbuilt air ioniser and plasma filter for better indoor air quality with 3 star rating and EER 3.2 of capacity 1.5 ton including cordless remote control unit, connection and testing complete all as specified and as directed. Make: Blue star Cat part No Blue star Cat Part No BI-3HW18IAU or equal approved in Voltas/Hitachi

SCHEDULE 'A' PART-II (Schedule of credit) Credit amount of Rs (Refer schedule of credit) for retrieved material mentioned in Sch 'A' Part-II of Tender documents in PDF form will be deducted offline during acceptance of tender of lowest bidder.

M/S GEE EMM MIR

Karmnaya Construction

MOHINDRA ENTERPRISES