CONSTRUCTION OF GOVERNMENT MEDICAL COLLEGE, 430 BEDDED HOSPITAL, GIRLS and BOYS HOSTEL 100 STUDENT CAPACITY AND RESIDENTIAL QUARTERS AT DHARASHIV DIST DHARASHIV

Cutting down trees including trunks and branches with girths above 180 centimetre to 270 centimetre and stacking the materials neatly with all lifts and lead of 1000 metre as directed and earth filling in the depression/pit if any.

Cutting down trees including trunks and branches with girths above 270 centimetre to 450 centimetre and stacking the materials neatly with all lifts and lead of 1000 metre as directed and earth filling in the depression/pit if any.

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 metre beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming , watering including shoring and strutting etc. complete. (Lift upto 1.5 metre) By Mechanical Means

Excavation for foundation in hard murum and boulders including removing the excavated material up to a distance 50 metres, beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming , watering including shoring and strutting etc. complete. (Lift upto 1.5 metre ) By Mechanical Means

Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material upto a distance of 50 metres beyond the building area and stacking as directed, including dewatering, preparing the bed for the foundation and necessary back filling with available earth/murum, ramming ,watering including shoring and strutting etc. complete. (Lift from 1.5 metre To 3.0 metre) By Mechanical Means

Excavation for foundation in Hard rock by chiselling, wedging, line drilling, etc. including tri millimetre ing and levelling the bed, removing the excavated material upto a distance of 50 metres beyond the building area stacking as directed, dewatering and back filling with available earth/ murum watering, ramming etc. complete. (Lift upto 1.5 metre). By Mechanical Means

Conveying materials obtained from road cutting including all lifts, laying in layers of 20 centimetre to 30 centimetre breaking clods, dressing to the required lines, curves, grades and section, watering and compacting to not less than 97% of standard proctor density for a lead of 300m. to 500m. inclusive, from the site of excavation to the site of deposition as directed.

Dewatering on BHP basis by using water pump including diversion of stream, providing cofferdams, earthern bunds etc. as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required by using 5.0 to 9.0 BHP pump etc. complete.

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper.

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per One Square Metre of surface area covering ten years guarantee on bond paper.

Filling in plinth and floors with approved excavated material in 15 centimetre to 20 centimetre Layers including watering and compacting etc. complete.

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 centimetre to 20 centimetre including watering and compaction etc. complete.

Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based Programmable Logic Controller (PLC) with Supervisory Control And Data Acquisition (SCADA) enabled Concrete Batch Mix Plant (Pan mixer) enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand Vertical shaft impact (VSI) Grade)

Providing and laying Cast in situ/Ready Mix cement concrete in M-15 of trap metal for foundation and bedding / steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.),with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand Vertical shaft impact (VSI) Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap metal for Reinforced cement concrete work in foundations like raft, strip foundations, grillage and footings of Reinforced cement concrete columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand Vertical shaft impact (VSI) Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap metal for Reinforced cement concrete columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based Programmable Logic Controller (PLC) with Supervisory Control And Data Acquisition (SCADA) enabled Concrete Batch Mix Plant (Pan mixer) enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand Vertical shaft impact (VSI) Grade) (For All Floors)

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap metal for Reinforced cement concrete beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based Programmable Logic Controller (PLC) with Supervisory Control And Data Acquisition (SCADA) enabled Concrete Batch Mix Plant (Pan mixer) enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand Vertical shaft impact (VSI) Grade) (For All Floors )

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap metal for Reinforced cement concrete slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based Programmable Logic Controller (PLC) with Supervisory Control And Data Acquisition (SCADA) enabled Concrete Batch Mix Plant (Pan mixer) enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand Vertical shaft impact (VSI) Grade) (For All Floors)

Providing and laying Cast in situ/Ready Mix cement concrete in M-40 of trap metal for Reinforced cement concrete pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based Programmable Logic Controller (PLC) with Supervisory Control And Data Acquisition (SCADA) enabled Concrete Batch Mix Plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand Vertical shaft impact (VSI) Grade) (For All Floors )

Providing and laying Cast in situ/Ready Mixcement concrete M-40 of trap metal for Reinforced cement concrete chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based Programmable Logic Controller (PLC) with Supervisory Control And Data Acquisition (SCADA) enabled Concrete Batch Mix Plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand Vertical shaft impact (VSI) Grade) (For All Floors )

Providing and laying Cast in situ/Ready Mix cement concrete in M-40 of trap metal for Reinforced cement concrete Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based Programmable Logic Controller (PLC) with Supervisory Control And Data Acquisition (SCADA) enabled Concrete Batch Mix Plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand Vertical shaft impact (VSI) Grade) (For All Floors)

Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap metal for Reinforced cement concrete coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including steel centering, formwork, cover blocks, laying/pumping, compacting , curing , finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based Programmable Logic Controller (PLC) with Supervisory Control And Data Acquisition (SCADA) enabled Concrete Batch Mix Plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand Vertical shaft impact (VSI) Grade) (For All Floors)

Providing and laying in situ M-20 cement concrete of trap / granite / quartzite / gneiss metal with 15% plum of trap stones for foundation and bedding of retaining walls and jetty etc. including necessary formwork, compacting, curing, bailing out water manually in tidal range etc. complete.

Providing and fixing in position Thermo Mechanically Treated (TMT) - FE - 500 bar reinforcement of various diameters for Reinforced cement concrete pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. (For All Floors)

Providing expansion joints in Reinforced cement concrete framed structure (at floor level) with plain premoulded filler 25 millimetre thick with 75 millimetre wide and 1 millimetre thick stainless steel plat and finishing etc. Complete. (For All Floors)

Providing expansion joints in reinforced cement concrete framed structure (interior columns) with plain premoulded filler with confirming to IS 1838,1961, 25 millimetre thick with 75 millimetre wide and 1 millimetre thick stainless steel plate finishing etc. complete as directed. (For All Floors)

Providing expansion joints in Reinforced cement concrete framed structure (exterior Columns) with plain premoulded filler 25 millimetre thick and 3 millimetre thick alluminium plate, hold fast, fixing T.W. battens on internal face, finishing etc. complete as directed. (For All Floors)

Providing expansion joints in Reinforced cement concrete framed structure (at Terrace level) with premoulded filler 25 millimetre thick with 40 millimetre wide and 1 millimetre thick stainless steel plate as required, bitumen poured filler and finishing etc. complete as directed. (For All Floor)

Providing and fixing interior wall to wall expansion joint cover model W-90 for 50 millimetre gap size, this surface mounted aluminium cover is designed for interior application where low maintenance is desirable. This model is made using Aluminium alloy 6063 and temper T5/T6. This cover is installed using stailness steel clip in the rear which helps the movement to + 10 millimetre

Providing and fixing of external wall to wall cover model ASM 200X for 50 millimetre gap size,this surface-mounted metal wall cover is designed for exterior applications where low maintenance or tamper-resistant applications are desired. The free-floating aluminum center plate spans the joint and slides over the surface of the wall to allow required movement.EPDM vapor barrier to protect the joint with water. This profile is extruded aluminum with ASTM B 221, Alloy 6063-T5. This profile has been tested under Architectural Testing Agency ( an Intertek Company) for the movement performance. The minimum opening of the profile is 10 millimetre ( -40 millimetre ) and the maximum openeing of the profile is 76 millimetre (+26 millimetre ) which is more than ±50% movement.

Providing and Fixing of external Roof cover model RJT 200 for 50 millimetre gap size, Aluminium roof cover comprised of extruded alumunium components, Injection molded turnbar, duroflex gaskets and EPDM vapor barrier.This profile is extruded aluminum with ASTM B 221, Alloy 6063-T5. This profile has been tested under Architectural Testing Agency ( an Intertek Company) for the movement performance. The minimum opening of the profile is 3 millimetre ( -47 millimetre ) and the maximum openeing of the profile is 92 millimetre (+42 millimetre ) which is more than ±50% movement.

Providing and fixing during laying in Reinforced cement concrete Slab rectangular 2 millimetre thick M.S. sheet fan hook box of size 180x100 millimetre with required depth with holes or notches as required, bottom and top sides of 1.6 millimetre M.S. sheet fixed with 3.5 millimetre diameter round headed screws together with 12 millimetre diameter M.S. bar bent to shape with hooked ends for fan hook and painting to exposed surface . (For All Floors )

Providing waterproofing in Water Closet. and bath including brick bat coba in all position including providing and laying 12 millimetre bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @ 1Kilogram/per bag of cement laying brick bat coba of required thickness in centimetre 1:5 with waterproofing compound 1 Kilogram/bag of cement grouting and finishing the top layer with 20 millimetre thick brick bedding in centimetre mortor 1:3 with waterproofing compound 1 Kilogram/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etc. complete. (For All Floors )

Providng Grouting by specially prepared grout of approved make chemical with cement in proportion 1:3.5 (1 part chemical & 3.5 part cement by weight) along wih 50 ml super plasticizer non cracking antiwash high strength polymer cement grout P C grout available in bags or equivalent with proper water for injectable consistency and applying it in the body of structure like slab, beam, column, pillars, deckslab, retaining wall, basement, underground and elevated water storage reservoir concrete and brick wall, crack portion of structure etc. by injectng method, to achieve its original strength including drilling of suitable diameter drills holes at 2 to 4 Nos. per sqm. using caps and nozzle grouting machinery necessary, scaffolding, finishing and covering gurantee of 10 years on court stamp paper of Rs. 100/- and necessary testing etc. complete.

Providing water proof bedding for flooring of Bath and Water Closet 25 millimetre thick in cement mortar 1:3 including using approved water proofing compound in specified proportion as per manufacturers specifications for per bag of cement including leveling, curing and covering 10 years guarantee on court fee stamp paper of Rs.500/- including ponding test etc. complete. (For All Floors )

Providing waterproof plaster in Water closet and bath 12 millimetre thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing etc. complete. (Excluding Tiles) (As directed by Engineer in Charge) (For All Floors )

Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in cement mortar 1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with cement mortar 1:3 admixed with approved water proofing compound and finally top finishing with average 20 millimetre . thick layers of same mortar added with jute fiber at 1Kilogramper bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300 millimetre x 300 millimetre . making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete.

Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in foundations and plinth of inner walls/ in plinth external walls including bailing out water manually , striking joints on unexposed faces, raking out joints on exposed faces and watering etc. Complete.

Providing second class Burnt Brick masonry at with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete. (For All Floors )

Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of 2 bars of 6 millimetre diameter / 2 hoop iron strips 25 millimetre X 1.6 millimetre placed at every third course, properly bent and bonded at ends scaffolding, racking out joints and watering etc. complete. (For All Floors )

Providing Autoclaved Aerated Concrete Block masonary of conforming to IS:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in superstructure including striking joints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972) (For All Floors)

Providing Autoclaved Aerated Concrete Block masonary of conforming to IS:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in Half brick thick wall including striking joints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972) (For all floors )

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 millimetre thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 millimetre thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. (For All Floors )

Providing and applying gypsum plaster ( with Gypsum material ) with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface ( Excluding rough cast plaster ) in all position including preparing and Finishing the surface scaffolding etc.complete. (For All Floors)

Providing internal cement plaster 20 millimetre thick in Single coats in cement mortar 1:4 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc.complete. (For All Floors )

Providing internal cement plaster 12 millimetre thick in single coat in cement mortar 1:3 without neeru finish to concrete or brick surfaces, in all position including scaffolding and curing etc. complete. (For all floors )

Providing neeru finish to plastered surfaces in all positions including scaffolding and curing, excetra complete. (For all floors )

Providing and fixing chicken mesh of 22 gauge, with about 30 centimetre width at the junction of Reinforced cement concrete members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete /B.B.masonry and or tying by binding wire etc. complete. (For All Floors)

Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface ,applying primer coat ,scaffolding if necessary, and watering the surface for two days etc complete. (For All Floors )

Providing and applying Royale Luxury Emulsion of approved make on internal wall surface as detailed below Scrapping for surface with emery paper and wipe clean for area. wall primer with brush by adding mineral turpentine oil by 8 to 10 % or water by 15 to 20% allowing to dry for 6 to 8 hoursAfter applying acrylic wall putty with appropriate prpportion of water of allow to dry for period of 4 to 6 hours of activity. Scrapping with emery paper and wipe clean Applying paints Royale Luxury emulsion 1st coat with brush water content water 40 to 45% or 65 to 70% by role Applying paints Royale luxury emulsion 2nd coat with brush with water content 40 to 45% or 65 to 70 % by roller. (For All Floors)

Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300 millimetre x 40 millimetre x 5 millimetre with oil painting, etc. Complete. (For all floors )

Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kilogram/ One Square Metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete. (For All Floors)

Providing and fixing mild steel grill work for windows, ventilators, etc. 15 Kilogram/ One Square Metre as per drawing including fixtures necessary welding and painting with one coat of anticorrosive paint and two coats of oil painting complete. (For All Floors)

Providing and fixing in position. (as per I.S.1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension ?63.50 x 38.10 x 1.02 millimetre at weight 0.547 kilogramme per one Running metre and window frame bottom track section 61.85 x 31.75 x 1.20 millimetre at weight 0.695 kilogramme per one Running metre Top and side track section 61.85 x 31.75 x 1.30 millimetre at weight 0.659 kilogramme per one Running metre The shutter should be of bearing bottom 40 x 18 x 1.25 millimetre at weight 0.417 kilogramme per one Running metre Inter locking section 40 x 18 x 1.10 millimetre at weight 0.469 kilogramme per one Running metre And handle section 40 x 18 x 1.25 millimetre at weight 0.417 kilogramme per one Running metre and top section 40 x 18 x 1.25 millimetre at weight 0.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 millimetre thick plain glass with all required screws and nuts etc, complete. With powder coating without box. (For All Floors )

Providing and fixing in position (as per 1868 / 1982) Aluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 millimetre at weight 0.637 kilogramme per one Running metre with window frame bottom track section 92 x 31.75 x 1.30 millimetre at weight 1.070 kilogramme per one Running metre . Top and side track section 92 x 31.75 x 1.30 millimetre at weight 0.933 Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 millimetre at weight 0.417 kilogramme per one Running metre Inter locking section 40 x 18 x 1.10 millimetre at weight 0.469 Kilogram/Running metre. and handle and top section 40 x 18 x 1.25 millimetre at weight 0.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 millimetre thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With powder coating without box. (For All Floors)

a) Supplying and fixing in position Aluminium four track sliding windows with outer frame made from section of over all size 122 millimetre x 45 millimetre , bottom section with drain section track weighing 1.83Kilogramper metre and top and side section of size 122x 31.75 millimetre weighing 1.15Kilogramper One Running Metre with shutter sections made of 18 millimetre x 40 millimetre size having average weight of 0.6Kilogramper One Running Metre (or as required size) with change in proportionate weight, with 6 millimetre float glass in three equal panels and alluminium coated stainless steel mosquito net in one (2/3 of opening) panel fixed with new neoprene gasket, shutters to be provided with nylon encased stainless steel rollers, necessary locks and handles complete. a) Colour anodized. (For All Floors )

Providing and fixing in position aluminium partly openable and partly fixed window of any size as per detailed drawing and as directed by Engineerincharge with all necessary alluminium sections including necessary fixtures and fastening with 5 millimetre thick float glass etc. complete. b) Color anodized Note While arriving at the rate of item of item weight at 6.90 Kilogram/ One Square Metre is considered. (For All Floors)

Providing and fixing fiber glass reinforced polyster door shutter 30 millimetre thick as per IS 14856 (2000) (Reaffirmed 2006) without ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, etc complete. (For all floors )

Providing and fixing Country cut teak wood double or single leaf panelled shutters, 35 millimetre thick style top and freze rail 95 x 35 thick with lock and bottam rail 195 x 25 millimetre thick and panels without ventilator as per detailed drawing excluding the door frame, stainless steel fixtures and fastening and finishing the wood work with oil painting 3 coats complete. (For all floors )

Providing and fixing the Country cut teak wood second class fully glazed openable fan light rectangular in shape as per detailed drawing excluding the frame,stainless steel fixtures and fastenings and finishing the wood work with 3 coats of oil painting. (For All Floors )

Providing and fixing ISI marked double swing flush door shutters conforming to IS :2202 (Part I) Non-decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 millimetre thick including ISI marked Stainless Steel L- hinges with necessary screws Fittings & Fixtures per leaf Stainless steel kick plates on both sides of the door of 300 millimetre height Heavy Duty satin finish butt SS Hinges (100 millimetre x 75 millimetre x 3 millimetre in size) -4 nos. SS finished lever handle with mortise lock- 1 One Number Floor spring- 1 One Number 100 millimetre x 100 millimetre safety glass at the specified location.(For All Floors)

Providing and fixing in position, Double shuttered aluminium extruded powder coated openable door of specified size with aluminium door frame of powder coated section 101.60 x 44.75 millimetre , 3.18 millimetre thick and shutter comprising of powder coated section having bottom and lock rail of size 150 millimetre x 44.5 millimetre x 3.00 millimetre thick top rails 47.62 x 44.45 millimetre x 3.00 millimetre thick , vertical style 47.62 x 44.45 millimetre , 3.00 millimetre thick and for shutter plain glass panes 5 millimetre thick for top panels and 12 millimetre thick both side laminated phenol bonded particle board panels for bottom panels etc. , I.S.I. mark , heavy duty, Hydraulic floor spring of 150Kilogramcapacity , having heavy duty concealed lock, necessary beading, glazing clips, Poly vinyl chloride gaskets, 250 millimetre length aluminium tower bolts, 150 millimetre diameter pad handle, etc. as per detailed design and drawing or as directed by engineer in charge including all materials , labours, and equipment etc.complete. (For All Floors)

Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 millimetre thick for door frame/ dado/ window boxing etc. on cement mortar . 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete. (For all floors )

Providing and laying ceramic tiles having size 30 centimetre x 60 centimetre confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete. (For all floors )

Providing and laying full body vitrified matt finish tiles having size 590 millimetre to 605 millimetre x to 605 millimetre of 8 to 10 millimetre thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete. (For all floors )

Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone slab or tile of approved shade and size 18 millimetre to 20 millimetre thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete. (For all floors )

Providing and laying full body vitrified matt fininsh tiles having size 590 millimetre to 605 millimetre x to 605 millimetre of 8 to 10 millimetre thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete. (For All Floors)

Providing leather finished polishing to Granite Stone slab by continuous grinding in 4 coats of different bits to receive rough and matt finish including buffing process before laying and fixing of stone as per drawing and design, including cleaning, washing and finishing etc. complete. (For all floors )

Providing and fixing machine cut machine polished 18 millimetre to 20 millimetre thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete.(For All Floors)

Providing structural steel work in single stanchions composed of R.S.J. Channel etc. with caps, bases, mild steel plated, angle brackets, cleats, gusset plates, anchor bolts etc. as per detailed designs and drawings or as directed including cutting, fabrication, hoisting, erecting fixing in position, making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it two. coats of oil painting approved quality and shade etc. complete. (For All Floors )

Providing, fabricating and erecting at site of work the tubular steel structure (shed) as per standard design and specifications having various spans in between trusses and in multiples of standard length of bays as specified as per standard specifications, inclusive of cost of steel tubular trusses, tubular columns purlins, tie runners, foundation bolts, base plates, nuts and bolts, welding wherever required etc. as per detailed drawing inclusive of one coat of anticorrosive paint and two coats of oil painting of approved quality and shade etc. complete. Spec. One Number : As directed by Engineer-in-charge. (For all floors )

Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 millimetre diameter and vertical pipe of 38 millimetre dia at 0.60 m c/c or as required and horizontal pipes of 25 millimetre dia in three rows, all pipes of 2 millimetre thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 millimetre dia above newel post of 75 millimetre diameter etc. complete. (For all floors )

Providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc. including welding grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts, etc. of the required size on the top of the floor of the side of waiste slab with suitable arrangement as per approval of engineer in charge (for payment purpose, only the weight of the stainless steel members shall be considered excluding fixing accessories such as nut bolts, fasteners etc.). 50 millimetre diameter pipe, 1.5 millimetre thickness and weight 1.92Kilogram/ running metre. (For all floors )

Providing and constructing granite kitchen platform with fixing of stainless steel sink 600 millimetre x 450 millimetre size as per detailed drawing including vertical both side polished kadappah stone 25 to 30 millimetre thick supports with kadappah top 35 to 40 millimetre thick and polished granite 16 to 20 millimetre top with side strips of granite at front and both sides of platform raised with two vertical granite supports 15 centimetre height and top granite of 75 x 40 centimetre including cutting, opening for sink of required size in kadappah as well as granite etc. complete. (Platform top size 5.00 metre x 0.60 metre and height is 0.75 metre) (For all floors )

Providing and fixing 15 centimetre x 10 centimetre salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap.

Providing and fixing 450 millimetre x 550 millimetre size superior type Belgium mirror with 16 millimetre diameter nickel plated towel rod etc. complete. (For all floors )

Providing and fixing Orissa type white glazed earthenware 575 millimetre water closet pan including S trap with earthenware foot rests, cast iron soil and vent pipe upto outside face of the wall 1:2:4 brick bat lime concrete bedding without flushing tank and its accessories etc. complete. (For all floors )

Providing and fixing screw down for 25 millimetre diameter wheeled stop tap of brass including necessary sockets/union nut complete. (For all floors )

Providing and fixing screw down for 32 millimetre diameter wheeled stop tap of brass including necessary sockets/union nut complete. (For all floors )

Providing and fixing White Glazed Earthenware full stall type Urinal with Poly vinyl chloride flushing cistern of 5 liters capacity with fitting, inlet pipes and stop tap, brackets for fixing the cistern, 32 millimetre diameter Poly vinyl chloride flush pipe with fittings and flushing arrangement including lead soil pipe, lead trap, soil pipe connectionup to the outside face of the wall. (For all floors )

Providing and fixing White Glazed Earthenware Squatting plate (Ladies Urinal) with Poly vinyl chloride flushing cistern of 5 liters capacity with fitting, inlet pipes and stop tap, brackets for fixing the cistern, 32 millimetre diameter Poly vinyl chloride flush pipe with fittings and flushing arrangement including lead soil pipe, lead trap, soil pipe connectionup to the outside face of the wall. (For all floors )

Providing and fixing push cock (Self closing tap) symet type of 20 millimetre diameter including necessary socket, testing etc. complete. (For all floors )

Providing and fixing White glazed with bottle trap earthenware Wash Hand Basin of 63x45 centimetre size including cold water piller taps, brackets, rubber plugs and brass chain, stop tap, chromium plate bottle trap and necessary pipe connections including UPAC waste pipe and trap upto the outside face of the wall, making good the damaged surface, testing etc. complete. (For all floors )

Providing and fixing European type wall-hung white water closet of approved make with push valve concealed type with cover plate 32 millimetre size of approved make including soil pipe, vent pipe up to outside face of wall ,100 millimetre diameter galvanised iron plug bend inlet pipe all fittings, cuttingand making good walls, floors etc. complete. (For All Floors )

Providing and fixing 75 millimetre diameter stabiliser pipe/ Poly vinyl chloride soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. (For all floors )

Providing and fixing 100 millimetre diameter stabiliser pipe/ Poly vinyl chloride soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. (For all floors )

Providing and fixing High Density Polymer (HDP) container one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet,outlet overflow pipe inclusive of all tanks capacity between 200 to 1000 liters. (For All Floors )

Providing and fixing on walls/ceiling/floor 20 millimetre diameter Chlorinated Poly vinyl chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. (For all floors )

Providing and fixing on walls/ ceiling/ floor 32 millimetre diameter Chlorinated Poly vinyl chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. (For All Floors )

Providing and fixing 8 centimetre Cast iron Nahani Trap including Cast iron grating bend and piece of Cast iron pipe upto the outside face of the wall complete. (For All Floors)

Providing and fixing 100 millimetre diameter chromium plated brass showers rose to 15 millimetre diameter supply pipe including necessary bend and socket complete. (For all floors )

Providing and fixing Chromium plated Angular stop clock with wall flange of approved make continental including necessary sockets/union nut etc. complete. (For All Floors )

Providing and fixing Chromium plated Two way BIB cock of approved make continental including necessary sockets/union nut etc. complete. (For all floors )

Providing and fixing Chromium plated BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete. (For all floors )

Providing and fixing wall mixer with overhead shower,shower arm,hand shower with wall bracket having flow rate up to 12 liters/minutes of Jaquar/Cera/Hindware /Perryware or equivalent make including all necessary pipes,fittings etc.complete as directed by Engineer In Charge.( Make shall conform to manufacturer's Green product and shall got approved from the Engineer In Charge.) (For all floors )

Supply and installation of cubicles of width and depth as per Athena Lite- SS Series Cubicles- Std Sizes (W x D x H): 900 millimetre x 1550 millimetre x 2105 millimetre , (Height is including 100 millimetre gap from bottom, Door Width- 600 millimetre specifications/ site drawings). Cubicle height to be 2105 millimetre . Made from solid grade compact high pressure laminate as per IS:2046 and EN-438 manufactured under high specific pressure > 5 MPa and temperature >120°C, All doors will be of single colour and made of 12 millimetre thick Merino HPL compact panel. The doors will have chamfered edges. Each door will be supported by 3 stainless steel made hinges affixed to the pilasters. Size of panels to be as per drawing. HARDWARE & ACCESSORIES are H shaped (Top) head frame structure made of extruded Aluminium grade 6063 T5-50 micron epoxy powder coated for surface protection, Size to be 125x70x5T. Corner joinery section, Size to be 40x16.5x1.8T. U-Channel Wall joinery section,Size to be 22x16x1.6T. Door stopper section, Size to be 21x12.5x1.6T. Spring loaded Butt Hinges made from Stainless steel grade 304. Surface finish to be matt type. Covers to be lacor coated.etc complete. (For All Floors )

Providing and constructing Brick Masonry Inspection Chamber 60 centimetre x 45 centimetre x 90 centimetre including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round Glazed stoneware pipes, Brick Masonry, plastering from inside and airtight cast iron cover of 75Kilogramwith lid and frame fixed in cement concrete.

Providing and constructing Brick Masonry Inspection Chamber 90 centimetre x 45 centimetre x 90 centimetre including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round Glazed stoneware .pipes, Brick Masonry, plastering from inside and Cast iron lid cover of 75Kilogramwith lid and frame fixed in cement concrete.

Providing and laying concrete pipes of Indian Standard Non-pressure class of 300 millimetre diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Providing and fixing machine cut mirror polished 18 millimetre to 20 millimetre thick telephone black granite / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone partition with full moulding the edges etc. complete . Both side polish. (For all floors )

Providing and fixing hume pipe septic tank 900 millimetre diameter with vent pipe and cap including necessary (including excavation and laying)

Providing soak pit of size 120 centimetre x 120 centimetre x 120 centimetre including excavating and filling with brick-bats.

Providing and fixing Poly vinyl chloride Rain water pipes of 110 millimetre outer diameter and having wall thickness of 2.2 to 2.7 millimetre confirming to I.S. 13592-1992 including proper rainwater receiving recess with Poly vinyl chloride plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25 millimetre to 40 millimetre from face of wall a fixing with clips of approved quality and One Number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on cement concrete . or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the Poly vinyl chloride fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete. (For All Floors )

Providing and fixing Chromium plated sink cock with raised J" shaped swinging casted spout ofapproved make including necessary sockets/ union nut etc. complete. (For All Floors)

Providing and fixing 15 millimetre diameter Poly vinyl chloride Aqua kraft type of approved make super jet spray with flange 2 in 1 faucet 1.50 metre long including all accessories etc complete. (For All Floors )

Providing, hoisting and fixing in position Cast iron manhole, frame and cover of best quality and of required size and shape with locking arrangements including applying 2 coats of anticorrosive paint,etc.complete.

Providing & fixing rubber water stopper, approvred make as per drawing & as per directedby engineer rtc complete

Providing and fixing solid core flush door shutter in single leaf 32 millimetre thick decorative type of exterior grade as per detailed drawings approved face veneers 3 millimetre thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete. (For All Floors )

Solid Core Flush door Double leaf Providing and fixing factory made solid core flush door shutters in double leaves 35 millimetre thick,decorative type of exterior grade, as per detailed drawings, conforming to I.S.: 2202 – 1966 (Revised) including approved face veneers on both sides, without glazing and venetians including mat finish stainless steel fixtures and fastening, stoppers and finishing with french polishing etc. (Excluding door frame)(Sample to be got approved from Ex. Engineer before use) Co millimetre ercial Hard Wood shutter. (For All Floors)

Providing and fixing in position alluminium strips of size 50 millimetre x 3 millimetre for nosing the steps including fixing with screws and raval plugs, bending and cutting to the required shape and size, finishing with paint, necessary mortar bedding of 1:3 cement mortar to get exact line and level including watering and curing etc.complete. (For All Floors )

Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 millimetre x 1.22 millimetre box type, 5 millimetre thick sheet glass louvers, of approved quality etc. complete. (For All Floors)

Providing , constructing and fixing 450 millimetre diameter Inspection chamber made up of Polypropylene / polyethylene material of thickness 3.5 millimetre and height of 388 millimetre with 160 or 200 millimetre main inlet (s) outlet and 110 and / or 160 millimetre branch inlets, with 450 millimetre diameter Ultra shaft pipe of HDPE material having height of 460 millimetre , having Reinforced cement concrete cover and frame fixing in 150 millimetre thick in c.c.1:2:4, having crushed sand bed of 150 millimetre thick of size 750 millimetre diameter Including excavation and refilling the sides of chamber by sand crushed cushioning 150 millimetre thickness, connecting all required UPoly vinyl chloride fittings with rubber lubricant etc. complete.

Providing , constructing and fixing 600 millimetre diameter Inspection chamber made up of Polypropylene / polyethylene material Having 315 millimetre diameter inlet(s)/outlets and with eccentric reducers as per requirement to connect 160 millimetre and 200 millimetre pipes having thickness of 5 millimetre and 600 millimetre in height, with inbuilt shaft achieve the invert depth as per site condition of wall thickness of 5 millimetre having Reinforced cement concrete cover and frame fixing in 150 millimetre thick in c.c.1:2:4, having crushed sand bed of 150 millimetre thick of size 750 millimetre diameter Including excavation and refilling the sides of chamber by ?sand crushed cushioning 150 millimetre thickness, connecting all required UPoly vinyl chloride fittings with rubber lubricant etc.complete.

Supply and Installation of translucent roof with DPI Flux standing seam multicell polycarbonate panel system. The system with complete assembly of co extruded UV protected multicell panels incorporated into a complete system. Co-extruded UV protected polycarbonate panel system of min 12 millimetre thick of 900 millimetre (min.) width with angular daylighting concept. Panels shall have minimum six layers with truss bridge design for higher flexibility & strength. Panels with all fixing accessories to ensure best performance for wind uplift, vibration, oil canning and visual appearance. Panels shall be manufactured with vertical standing seam at both sides of the panel. Panels shall be fixed on Purlin with snap on connectors with double tooth grip lock locking mechanism and will be secured on MS structure (will be paid Separately) with 3 One Numbers self-drilling screws & trapezoid SS fasteners holding the base of the standing seam offering best stability having a pull-out load of min. 7000N (7KN) tested as per ISO 6892:1998 and IS 1608: 2005, as per design requirement. Panels must satisfy Dart drop impact test as per IS 14443-97 shall show no sign of breakage on Polycarbonate sheets which have been exposed to UV for a min. of 500 Hours as per ASTM G 155. Panels shall not have Yellowness Index as per ASTM D 1925 of 15 units when tested on a sample exposed to UV for 500 Hours as per ASTM G 155. U value shall not be more than 1.6 W/m2K as per EN ISO 10077-2:2018. Panel shall be with additional End cap/Aluminium U/F profile/ Glazing Bar for ends as required. Panel shall be fixed over MS structural steel/MS purlin (paid separately) conforming to the detail technical specifications as per approved architectural drawings. Trained and factory authorized labour with supervision to complete the entire panel installation as per drawing & direction of the engineering in charge. Colour: As per Approval. Approved Make: FLUX by DPI Daylighting or approved equivalent The 12 millimetre thick panels shall be used for a roofing height of upto 15 mtrs.(For all Floors)

Providing and fixing in position aluminium fixed window fully glazed of any size as per detailed drawing and as directed by Engineer in charge with all necessary alluminium sections including necessary fixtures and fastening such as 5 millimetre thick clear float glass etc.complete. Note While arriving at the rate of item of item weight at 6.90Kilogram/ One Square Metre is considered.a) Colour anodized. (For All Floors)

Excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50m. and spreading for embankment or stacking as directed.

Excavation for roadway in hard murum and boulder including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50m.and spreading for embankment or stacking as directed.

Conveying materials obtained from road cutting including all lifts, laying in layers of 20 centimetre to 30 centimetre breaking clods, dressing to the required lines, curves, grades and section, watering and compacting to not less than 97% of standard Proctor density for a lead of over 50m. to 300m. inclusive from the site of excavation to the site of deposition as directed.

Supplying hard murum/ kankar at the road site, including conveying and stacking complete.

Spreading hard murum/ soft murrum/ gravel or kankar for side width complete

Compacting the hard murum side widths including laying in layers on each side with vibratory roller including artificial watering etc. complete.

Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at Optimum moisture content, carriage of mixed Material to work site, spreading in uniform layers with motor grader / Paver on prepared surface and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- Plant Mix Method and Grading - II Material

Wet Mix Macadam -- Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density. Laying By Grader/Paver.

Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate ( natural sand/ Vertical shaft impact (VSI) grade finely washed crushed sand) conforming to IS: 383, the size of coarse aggregate not exceeding 25 millimetre , , cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/ Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor /by suitable means as approved by Engineer-in-charge , compacting with vibratory roller, finishing, curing and including preparation of sub-grade surface if required etc. complete. with fully automatic micro processor based Programmable Logic Controller (PLC) with Supervisory Control And Data Acquisition (SCADA) enabled Concrete Batch Mix Plant (Pan mixer) enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete.

Providing and laying in-situ M30 Grade unreinforced plain cement concrete pavement over a prepared sub base with 43 grade cement , coarse and fine aggregate( natural sand/ Vertical shaft impact (VSI) grade finely washed crushed sand) conforming to IS 383, using fine and coarse aggregates combined gradation as per Table 600-3 of MORTH Specification 2013, mixed in a batching and mixing plant/ non tilting mixer and Weigh batcher as per approved mix design, admixtures, transporting to site, spreading, laying with approved make paver,compacted and finished in a continuous operation, finishing to lines and grades as directed by Engineer-in-charge and curing by curing compound /by providing cement vata in cement Mortar 1:8 @0.6m X 0.6m centre to centre, admeasuring 80 millimetre at bottom and 40 millimetre at top with depth of 75 millimetre and maintaining the same throughout curing period by any other method approved by Engineer-in-charge. with fully automatic micro processor based Programmable Logic Controller (PLC) with Supervisory Control And Data Acquisition (SCADA) enabled Concrete Batch Mix Plant (Pan mixer) enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete.

Providing and laying in situ / ready mix M20 Reinforced cement concrete of trap/ granite/ quartzite/ gneiss metal for Reinforced cement concrete work of ballast walls, kerbs and box returns including scaffolding, compaction, formwork finishing and curing etc. complete. (excluding reinforcement, with fully automatic micro processor based Programmable Logic Controller (PLC) with Supervisory Control And Data Acquisition (SCADA) enabled Concrete Batch Mix Plant (Pan mixer) enabled concrete batch mix plant / pan mixer with fine agreegates of required specifications ( Vertical shaft impact (VSI) sand finely washed etc ) Reinforced cement concrete work of Ballast walls & Kerb

Providing and fixing in position Thermo Mechanically Treated (TMT) FE 500, 32 millimetre dia dowel bars precoated with anticorrosive epoxy paint of requireddiameter 60 cms. Long and at 30.00 centimetre centre to centre and wherever directed including handling, straightening, necessary cutting supported by Thermo Mechanically Treated (TMT) FE 500, chairs with proper alignment by using properly designed assembly of Bulkheads lubricating half length with bituminous paint as directed etc. complete.

Cutting transverse contraction joints 3 to 4 millimetre wide and depth 60 millimetre . .in concrete slab using concrete cutting machine with diamond studded saw within 48 hours of casting of bay / slab etc. complete including subsequent widening of the groove 8 to 10 millimetre . wide at top having depth of 15 millimetre . as directed by Engineer incharge.

Providing and Laying hot applied thermoplastic road marking strip on Bituminous Surface of specified shade/ colour of 2.5 millimetre thick including 1.5 Refractive index reflectorizing glass beads @ 250gm/sqm .Thickness of 2.5 millimetre is exclusive of surface applied glass beads as per IRC 35:2015. Initial Dry reflectivity RL shall be > 250 mcd/sqm/lux measured in the initial 7 days and sustained reflectivity RL of 100 mcd/sqm/ lux and Qd of 100 mcd/sqm/ lux measured at the end of 2 years by means of a Standard Reflectometer of Zehntner, Easylux, Delta make capable of measuring RL & QD both according to IRC 35:2015 clause 15.5. The finished surface to be level, uniform, and free from streaks and holes complete as per direction of Engineer-in-charge and in accordance with applicable specifications.(Refer MORTH Clause 803 for technical Specification and Performance for IRC 35:2015).

Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete.

Providing and applying two coats (exterior quality) of flat oil paint of approved colour and shade to the plastered surface in buildings and workshops including scaffolding if necessary, cleaning the surface and preparing surface etc. complete. (excluding primer coat)

Providing and laying concrete pipes of Indian Standard Non-pressure . class of 150 millimetre diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Providing and fixing reinforced cement concrete cover of size 90 centimetre x 45 centimetre with frame over inspection chamber etc. complete. Heavy duty (225 Kilogram)

Providing and fixing reinforced cement concrete cover of size 60 centimetre x 45 centimetre with frame over inspection chamber etc. complete.Medium duty (100 Kilogram)

Providing and fixing Ductile iron Man Hole Covers/ Strom Water Grating and Grating with frame of Various sizes, weight and types and load bearing capacity as per EN-124, equivalent NECO with prior approval of concerned Superitending Engineer.

Supplying and Fixing of Molded Shank Raised Pavement Markers / Cat's Eye made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97 DO III Dt 11.06. 1997. The height, width and length shall not exceed 50 millimetre , 100 millimetre and 102 +/- 2 millimetre and with minimum reflective area of 13 Sq centimetre on each side and the slope to the base shall be 35 +/- 5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 millimetre and height not less than 30+/- 2 millimetre ) from the body is to be a minimum value of 500 Kg. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's reco millimetre endation and complete as directed by the engineer.The contractor shall submit a two year warranty for satisfactory field performance including stipulated retro-reflectance of the reflecting panel, to the Engineer.

Providing and constructing Brick Masonry Inspection Chamber 90 centimetre x 45 centimetre With Reinforced cement concrete raft in black cotton soil area including cost of reinforcement, 1:2:4 cement concrete channels half round glazed stoneware pipes, Brick Masonry, plastering from inside and airtight with 75 millimetre thick Reinforced cement concrete cover medium duty 140 Kilogram etc. complete.

Providing and fixing Cautionary/Warning sign boards in Equilateral Triangle size of 750 millimetre made out of 4_ millimetre aluminum sheet bonded with white retro reflective sheeting of Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3 Supported with back support frame 25 millimetre x 25 millimetre x 3 millimetre , duly painted on back side with grey stove enamel paint and supported on one no. of M. S. angle iron post of size 65 millimetre X 65 millimetre X 6 millimetre , 3.45 m long, duly painted with with flat oil paint having alternate black and white bands of 25 centimetre width including galvanised iron fixtures etc; fixing the boards in M25 grade concrete block of size 60 centimetre X 60 centimetre X 75 centimetre including transportation etc; complete. Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier.

Providing and fixing heavy duty inter locking concrete Grey paving blocks of 80 millimetre thickness of having a strength of 300 Kilogram/Sq. centimetre of approved quality and shape on a bed of crushed sand of 25 to 30 millimetre thick including skirting joints and cleaning etc. complete.

Providing and Laying of Rumble strips with Plastirib 2K, or equivalent 2 component cold plastic profiled material to give total width of 500 millimetre and height of 10 millimetre . Ramp provided to give width of 145 millimetre , width of ribs to be 55 millimetre laid at centre to centre distance of 35 millimetre , with reflective glass beads @ 350 gm / One Square Metre. The finished surface to be levelled, uniform and free from streaks and holes, to be applied on the edge lines, including surface cleaning and cost of all materials etc. complete.

Empty boring for 425 to 500 millimetre diameter Bored Reinforced cement concrete cast in situ pile including withdrawal of shell, removal of earth to a distance of 50 metres etc. complete.Spec :(As directed by Engineer in Charge)

Providing and laying cast in situ/ ready mix cement concrete M-20 for single rim bored pile of 450 millimetre diameter each of load capacity as per design and specifieddiameter of pile and bulb as directed, sunk to the required depth through all strata except rock,excluding provision of reinforcement including placing with fully automatic micro processor based Programmable Logic Controller (PLC) with Supervisory Control And Data Acquisition (SCADA) enabled Concrete Batch Mix Plant (Pan mixer) enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand Vertical shaft impact (VSI) Grade) by tremie arrangement compaction of concrete including chipping and dressing etc. complete. (Excluding steel reinforcement)

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 centimetre to 20 centimetre thick including hand packing and compacting etc. complete.

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap metal for Reinforced cement concrete pile cap as per detailed design and drawings, including bailing out water manually, centering, formwork, laying/ pumping, compacting, finishing and curing etc. with fully automatic micro processor based Programmable Logic Controller (PLC) with Supervisory Control And Data Acquisition (SCADA) enabled Concrete Batch Mix Plant (Pan mixer) enabled reversible Drum Type mixer/ complete.with Crushed sand Vertical shaft impact (VSI) Grade/Vertical shaft impact (VSI) quality Artificial Sand, complete.concrete Batch mix plant (Pan mixer) etc.(Excluding steel )

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for Reinforced cement concrete columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based Programmable Logic Controller (PLC) with Supervisory Control And Data Acquisition (SCADA) enabled Concrete Batch Mix Plant (Pan mixer) enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand Vertical shaft impact (VSI) Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap metal for Reinforced cement concrete beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based Programmable Logic Controller (PLC) with Supervisory Control And Data Acquisition (SCADA) enabled Concrete Batch Mix Plant (Pan mixer) enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand Vertical shaft impact (VSI) Grade)

Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for Reinforced cement concrete pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting , curing , finishing and rougheningthem if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand Vertical shaft impact (VSI) Grade)

Providing and installing bio digester unit based on DRDO technology made of fibre reinforced plastic (FRP) having composition and following technical specifications and including necessary pipe and accessories up to 3 meter length, excluding the necessary excavation for installing the bio digester. Percentage of fibre glass (glass content in fibre glass should be minimum 30%): 33.33% Percentage of polyester resin: - 66.67% Water absorption (as per ASTM):-0.30% Fla millimetre ability as per ASTM Tensile strength:-115 MPA Specific Gravity at 25 degree centigrade 1.45 Izod impact strength:-65KJ/M2 Heat defection/distort temperature:-65deg C Corrosion resistance (Non Corrosive) fitted with Inlet pipe size rigid Poly vinyl chloride : -100 millimetre Outlet pipe size rigid Poly vinyl chloride :-80 millimetre Gas outlet rigid Poly vinyl chloride with Valve: 20 millimetre Bacteria i millimetre obilization Poly vinyl chloride mattes (on all partition) With DRDO TOT licensee and atest batch certificate (month & year of supply) and capacity as below l) Up to 500 user size (6mx2.0mx1.6m), Capacity of Biodigester:-20000 liters, Area of top, bottom and side walls: - 50.72 sq.m, Area of partition walls: 13.36sq.m, Total weight of FRP: - 917.86 Kilogram, Bacteria inoculums quantity: - 7000 liters, Minimum thickness of side walls / top and bottom: 9 millimetre , One Number of inside partitions: - 4, Minimum thickness of partition wall: 4 millimetre

Providing and laying mechanical protective layer over water proofing membrane with cement screed plaster 1:5 after laying chicken mesh over membrane including curing etc. complete 20 millimetre thick with cost of chicken mesh etc. complete and covering 7 years guarantee on court stamp paper of Rs.100/- including necessary testing specified by Engineer

Providing and laying in situ M-20 cement concrete of trap metal with 15% plum of trap stones for foundation and bedding of retaining walls and jetty etc. including necessary formwork, compacting, curing, bailing out water manually in tidal range etc. complete.

Designing (aesthetically), and constructing Reinforced cement concrete ground service reservoirs / Reinforced cement concrete sumps in M-300 mix of required capacity including excavation in all types of strata, foundation concrete, container walls, bottom slab top Reinforced cement concrete roof slab / or dome, 20 millimetre thick cement plaster with water proofing compound in centimetre 1:3 proportion to inside face of the container, including epoxy paint from inside including refilling and disposing of surplus stuff within lead of 50 M, all labour and material charges, for laying and jointing of pipe assembly for inlet, outlet washout, over flow and bypass arrangement consisting of Cast iron M.S. D/F. pipes, specials and valves of given diameters, providing and fixing accessories such as M.S. ladder inside and outside, Cast iron Manhole frame and cover, water top slab, B.B. masonry chamber for all valves, ventilating shafts, including giving satisfactory hydraulic test and water tightness test as per IS code and providing three coats of cement paints to all exposed surface of structure including roof surface etc. complete as per design data, criteria, obligatory requirements and detailed specifications. Anti-termite treatment shall be given for underground portion of the structure. a)Cost of 5,00,000 litres capacity

Designing (aesthetically), and constructing Reinforced cement concrete ground service reservoirs / Reinforced cement concrete sumps in M-300 mix of required capacity including excavation in all types of strata, foundation concrete, container walls, bottom slab top Reinforced cement concrete roof slab / or dome, 20 millimetre thick cement plaster with water proofing compound in centimetre 1:3 proportion to inside face of the container, including epoxy paint from inside including refilling and disposing of surplus stuff within lead of 50 M, all labour and material charges, for laying and jointing of pipe assembly for inlet, outlet washout, over flow and bypass arrangement consisting of Cast iron M.S. D/F. pipes, specials and valves of given diameters, providing and fixing accessories such as M.S. ladder inside and outside, Cast iron Manhole frame and cover, water top slab, B.B. masonry chamber for all valves, ventilating shafts, including giving satisfactory hydraulic test and water tightness test as per IS code and providing three coats of cement paints to all exposed surface of structure including roof surface etc. complete as per design data, criteria, obligatory requirements and detailed specifications. Anti-termite treatment shall be given for underground portion of the structure. b)Cost of 15,00,000 litres capacity

Designing (aesthetically), and constructing Reinforced cement concrete ground service reservoirs / Reinforced cement concrete sumps in M-300 mix of required capacity including excavation in all types of strata, foundation concrete, container walls, bottom slab top Reinforced cement concrete roof slab / or dome, 20 millimetre thick cement plaster with water proofing compound in centimetre 1:3 proportion to inside face of the container, including epoxy paint from inside including refilling and disposing of surplus stuff within lead of 50 M, all labour and material charges, for laying and jointing of pipe assembly for inlet, outlet washout, over flow and bypass arrangement consisting of Cast iron M.S. D/F. pipes, specials and valves of given diameters, providing and fixing accessories such as M.S. ladder inside and outside, Cast iron Manhole frame and cover, water top slab, B.B. masonry chamber for all valves, ventilating shafts, including giving satisfactory hydraulic test and water tightness test as per IS code and providing three coats of cement paints to all exposed surface of structure including roof surface etc. complete as per design data, criteria, obligatory requirements and detailed specifications. Anti-termite treatment shall be given for underground portion of the structure. c)Add for capacity above 15,00,000 litres

Single Bed @ 2025LX 1000DX 650H Providing and fixing Single Bed of Size 2025Lx1000Dx650H with matress and pillow. Understructure: - The legs are made of Square tube of size 25 x 25 millimetre made out of MS with a thickness of 1.2 millimetre . The legs should have corner brackets welded to it at two levels. The corner brackets are made of 2 millimetre thick CRCA having a L shaped structure to join the side panels and headboard to the leg. Three nos. of Horizontal stiffeners are provided at equal intervals. The stiffeners are made of Square tube of size 25 x 25 millimetre made out of MS with a thickness of 1.2 millimetre . The middle Horizontal Stiffener has a leg attached to it to transfer the load to the ground and add to the strength and stability of the complete structure. This leg is also made of Square tube of size 25 x 25 millimetre made out of MS with a thickness of 1.2 millimetre . All Metal components to undergo 7 tank treatment process and should be powder coated to the thickness of minimum 50 Microns DFT.Side Panel: - The side panels are made up of 18 millimetre thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2 millimetre thick Poly vinyl chloride edge Banding. The overall width of the side panel is 150 millimetre . The side panels have 18 millimetre thick prelam particle board Baton running for required length to add rigidity to the structure. Head Board :- The head board is made up of 18 millimetre thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2 millimetre thick Poly vinyl chloride edge Banding. The head board size to be considered as 1000 x 650 millimetre . Foot Board :- The foot board is made up of 18 millimetre thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2 millimetre thick Poly vinyl chloride edge Banding. The head board size to be considered as 1000 x 450 millimetre . Bed Base: - The Bed Base is made up of 12 millimetre thick Prelam Particle Board with both side White laminate. (For All Floors)

Wardrobe with Mirror @ 900LX 600DX 1965H Providing and Fixing Wardrobe with Mirror of size 900LX 600DX 1965H The wardrobe side panels and doors are made up of 18 millimetre thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2 millimetre thick Poly vinyl chloride edge Banding. The shelves are made of 18 millimetre thick Prelam Particle Board with decorative laminate on both sides. The top is made of 36 millimetre prelam particle board with decorative laminate on both sides. (18 millimetre Prelam Particle board and 18 millimetre batons on all sides to achieve 36 millimetre overall thickness). The exposed edges of the top are sealed with 2 millimetre thick Poly vinyl chloride edge Banding. The top most part of the wardrobe has an aluminum hanger rod of EBCO make. One drawer of size 400(W) x 150(H) x 450 (D) made of 18 millimetre thick prelam Particle Board has been considered. The drawer will have a multipurpose lock of EBCO premium make. The wardrobe handles are Satin SS finish of 160 millimetre pitch. The wardrobe has a multipurpose lock of EBCO make. All hinges considered are Hettich make. Necessary good quality hardwares have been considered as required. (For All Floors)

Free Standing Table @ 1200Lx600Dx750HT Providing and fixing Table of Size 1200 x 600 x 750 millimetre . Top: made from 25 millimetre Prelaminated Particle board. All edges are covered by 2 millimetre . Thk. Poly vinyl chloride edge bands glued by hot melt glue applied by auto edge banding machine. Legs : C Shape made from CRCA Sheet with Powder Coat finish. Modesty panel : Made from 18 millimetre both side prelaminated particle boards.All edges are covered by 0.8 millimetre Poly vinyl chloride edge bands glued by hot melt glue applied by auto edge banding machine.KEYBOARD TRAY ( WITHOUT MOUSE TRAY ) :- Metal Powder Coated - Black Color, CPU TROLLEY :- Metal Powder Coated - Black Color, 3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. millimetre . with central lock and key. Drawers and body are complete metal with powder coat finish, facia in 18 millimetre prelaminated particle board. (For All Floors )

Book Case with Glass Shutter @ 825Lx300Dx1650HT Providing & Fixing of Book Case with Glass Shutter @ 825Lx300Dx1650HT:- To be made out of complete body & in 0.7 millimetre thick CRCA & Shutter in 1.2 millimetre thick CRCA with glass pannel in Powder coating finish as per drawing. (For all floors )

Providing & Arrangemnt of Mid Back, ECO CTS Mechanism , Fixed Armrest , Gaslift for Seat height adjustment, Standard 5-prong P/Nylon Base with Fabric Upholstery. (For all floors )

Sofa Set 3+1+1 Providing & fixing Sofa Set 3+1+1 Brown and Cream leather DIMENSION Length: 182.5 (cms) Breadth (cms): 100 (cms)Height (cms): 100 (cms) Weight (Kilograms): 66 (Kilogram) Seating Capacity: Five Seat. (For all floors )

Credestal @ 1200Lx450Lx650HT Providing & Fixing of LOW HEIGHT CREDESTAL @ 1200L X 450D X 650H :- To be made out of Membrane Finish ( 2 Openable Shutter & 3 Drawer Pedestal in between )as per drawing. (For all floors )

Bed Side Table @ 400LX 400DX 415H Providing and Fixing Bed Side Table of size 400LX 400DX 415H The bed side unit is made up of 18 millimetre thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2 millimetre thick Poly vinyl chloride edge Banding. The bed side table has one drawer and one shelf. The shelf is made of 18 millimetre thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2 millimetre thick Poly vinyl chloride edge Banding. (For all floors )

Medium Height Steel Storage @ 750Lx450Dx1200HT Providing and fixing Openable Steel Storage of 750 x 450 x 1200Ht, with 2 adjustable shelves, Complete body & shutter made in 0.8 millimetre thick & Top in 2 millimetre thick CRCA, 2 Shutter to be mounted with the help of cup hinges, and 4 adjustable levelers, enitre storage in powder coated finish with 60 to 80 microns. with 25 millimetre . thk. as per drawing. (For all floors )

Dressing Table @400LX 400DX 1800H Providing & Fixing Dressing Table of size 400LX 400DX 1800H.The Dressing table unit is made up of 18 millimetre thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2 millimetre thick Poly vinyl chloride edge Banding. The unit has one drawer and one shelf. The dressing table has a mirror of 4 millimetre thick pasted on 18 millimetre thick prelm particle board attached to the base unit. The mirror size considered is 1155 x 360 x 4(t). The mirror has been pasted using high quality 3M sticker. (For all floors )

Tea Table 900 millimetre X 750 millimetre X 450 millimetre for m.s. ante chamber Providing And Fixing Of Tea Table 900 millimetre X 750 millimetre X 450 millimetre With 12 millimetre Thick Colour Eitched Tempered Glass With Bevelled Drawing Made Out Of 18 millimetre Thick Waterproofing Ply. The Outer Laces To Be Finished With High Quality 4 millimetre Thik Veneer Or 1 millimetre Thik Mica Etc. (For all floors )

Providing and fixing in position Gypsum board false ceiling with 12.5 millimetre thick Gypsum boards, screwed/fixed to the under structure of suspended galvanised iron Grid constructed and suspended from the main ceiling consisting of ceiling sections of size 25 x 50 millimetre maximum center to center distance of 600 milimetre perimeter channel and intermediate channels at maximum center to center distance 1200 milimetre galvanized grid should be fixed to reinforced cement concrete slab. The gypsum board should be fixed to galvanized iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should include necessary additional ceiling sections and intermediate channels. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimetre item to be completed in all respect including necessary sleeves for ducts finishing of joints cut outs, painting including labour, material, lifts etc. all complete. (For All Floors)

Liquid Limit & Plastic Limit for Plinth Filling

Standard Consistancy, Fineness, Specific Gravity, Setting Time (Initial and Final), Compressive Strength, Soundness Test for Cement

Fineness Modulus (Sieve Analysis), Silt and Clay Content Test for Artificial Sand

Sieve Analysis Test for Metal below 40 milimetre

Water Absorption, Specific Gravity, Impact Value, Crushing Value Test for Metal below 40 milimetre

Compressive Strength of Cement Concrete Cube

Concrete Mix Design (with all tests on basic materials) for Grade M-40

Concrete Mix Design (with all tests on basic materials) for Grade M-20

Fineness Modulus (Sieve Analysis), Silt and Clay Content Test for Sand

Crushing Value / Compressive Strength, Water Absorption, Specific Gravity Test for Stone / Rubble

Tensile Strength, Percent Elongation, Yield Stress, Weight per Metre, Bend /Rebend Test, Proof Stress (Steel Bar upto 16 milimetre)

Tensile Strength, Percent Elongation, Yield Stress, Weight per Metre, Bend /Rebend Test, Proof Stress (Steel Bar above 16 milimetre)

Water Absorption, Compressive Strength, Efflorescence Test for Burnt Bricks

Compressive Strength of Cement Mortar

Density, Moisture Content for Wood

Thickness, Mass per Running Metre of Aluminium Section

Water Absorption, Modulus of Rupture Test for Ceramic / Vitrified Tiles

Water Absorption, Compressive Strength, Efflorescence Test for Fly Ash Bricks

Sieve Analysis Test for Hard Murrm

Liquid Limit and Plastic Limit for Hard murum

Granular Sub-Base Mix Design

Compaction Test (Proctor Density) for earth work

Fineness Modulus (Sieve Analysis), Silt and Clay Content Test for Metal below 40 milimetre

Wet Mix Macadam Mix Design

Concrete Mix Design (with all tests on basic materials) for Grade M-30

Compressive Strength, Water Absorption Test for Paving Blocks - 80 milimetre thick, 300 Kilogram per Square Centimetre Strength

Fineness Modulus (Sieve Analysis), Silt and Clay Content Test for Sand

Royalty charges

Supplying, erecting & marking SPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking TPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 4 ways/phase (12 poles), with door, 1.2mm thickness, surface/flush mounted, IP 43 protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 8 ways / phase (24 poles), with door, 1.2mm thickness surface/ flush mounted, IP 43 Protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SP/TP MCBs total 4 ways /12 Poles, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Supplying, erecting & commissioning 4 pole RCCB 16/25A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying, erecting & commissioning 4 pole RCCB 40A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 25 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 35 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 50 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 70 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 95 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 120 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 150 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 185 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½core 240 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 150 mm width & 75 mm height complete with necessary coupler plates & hardware.

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 200 mm width & 75 mm height complete with necessary coupler plates & hardware.

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 300 mm width & 75 mm height complete with necessary coupler plates & hardware.

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 400 mm width & 75 mm height complete with necessary coupler plates & hardware.

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 500 mm width & 75 mm height complete with necessary coupler plates & hardware.

Supplying & erecting conventional spike type air termination suitable to carry lightning stroke made up of heavy gauge 40 mm dia copper pipe of standard length with 5 Nos. copper spikes fixed on copper ball as air terminals duly threaded in copper pipe erected on provided foundation complete.

Providng earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Supplying and erecting GI strip of high purity required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint with joints required. As per specification no EA-EP.

Supplying and erecting GI wire of high purity of required sizes used for earthing or any other purposes on wall with necessary G. I. Clamps fixed on wall/cable/ conduit with screws complete.

Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Supplying and erecting mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying and erecting mains with 1x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying and erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying and erecting mains with 1x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Point wiring for light/bell/exhaust fan in 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW.

Secondary point wiring for additional light/ bell point, concealed type in min 20 mm FRLS grade PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires with required accessories as per specification No: WG-PW/CW

Wiring for plug on board with Switch socket surface/concealed type, copper wiring and earthing and with modular accessories as per specification No: WG-PW/CW

Point wiring for ceiling fan concealed type in min 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/CW

Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch 16A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch 16 / 20 A with indicator, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 3 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 4 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 8 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting modular type blanking plate one module, duly erected on provided plate & box.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 12 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting LED square / circular Max. 7W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 770 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting LED square / circular Max. 11 W down lighter/Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 1200 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting anodized aluminium corridor / passage / mirror light LED fitting (2 feet) Max. 12W with high transitivity diffuser with min. system lumens output of 1200 lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver with end caps on provided PVC Block / wooden board with 3 years warranty.

Supplying and erecting LED square / circular Max. 18 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting LED square / circular Max. 25 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2750 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting anodized aluminium corridor / passage light LED fitting (4 feet) Max. 22W with high transitivity diffuser with system lumens output of Min.2200 lumens , min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver, with end caps on provided PVC Block / wooden board with 3 years warranty.

Supplying and erecting energy saving ceiling fan 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Supplying and erecting electronic type step regulator for ceiling fan 600/ 900/ 1200/ 1400 mm. sweep, complete erected on provided switch board.

Supplying and erecting exhaust fan heavy duty 230 V, A.C. 50 cycles 375/380 mm. 900 RPM complete erected in position as per specification no. FG-FN/EXF

Supplying and erecting 150 kVAr, 3 phase, 50 Hz., Power contactors Derated for microprocessor APFC controller with MPP / APP type capacitor with 525 V and having minimum overcurrent capacity of 1.8 In, peak inrush current capacity 300 In and minimum life 150000 hours with , consisting of suitable steps of MPP/APP type capacitor units with detuned aluminium filter 7% reactors with circuit breaker as main incomer and MCCB for each branch protection, as per specification no CP-ED/APFC

Supply, erecting, testing and commissioning of Hostel Building Main LT Panel . All incomer fedder shall be With ON, OFF & Trip Indication. All the components shall be housed in a common cubical made of 16 swg. M.S.sheet. The panel shall be powder coated of approved colour both inside & out side.The panel shall have both bottom & top cable entry provisions and panel shall be mounted on Pedestal of 300 mm height with necessary accessories etc completed. Panel Shall be Indoor type With IP 43 Protection & Form-3B Sepration. Panel Shall Be As Per IEC 61439. As per CSR spacification (SW-MCB,SW-MCCB, SW-ACB,CP-BB,CP,WG MA/BW,WG-MA CON ) INCOMER - 160A TP ACB, EDO Type - 01 Nos 1 Sets of 2000 Amps. Aluminium Bus bars with colour coded heat shrinkable PVC sleeves, 1 Set of RYB indicating lamps with individual MCB's, 1 Nos of Multifunction Meters . All Incomer shall be with surge protection. OUTGOING - 500A TP MCCB With microporcessor based LSIGN Protection - 4 Nos.100A TP MCCB With microporcessor based LSIGN Protection - 2 Nos.

Supply, erecting, testing and commissioning of Hostel Building Submain Panel . All incomer fedder shall be With ON, OFF & Trip Indication. All the components shall be housed in a common cubical made of 16 swg. M.S.sheet. The panel shall be powder coated of approved colour both inside & out side. The panel shall have both bottom & top cable entry provisions and panel shall be mounted on Pedestal of 300 mm height with necessary accessories etc completed.Panel Shall be Indoor type With IP 43 Protection & Form-3B Sepration. Panel Shall Be As Per IEC 61439.As per CSR spacification (SW-MCB,SW-MCCB, SW-ACB,CP-BB,CP,WG MA/BW,WG-MA CON ) INCOMER - 500A TP MCCB With microporcessor based LSIGN Protection - 01 Nos 1 Sets of 630 Amps. Aluminium Bus bars with colour coded heat shrinkable PVC sleeves, 1 Set of RYB indicating lamps with individual MCB's, 1 Nos of Multifunction Meters . All Incomer shall be with surge protection. OUTGOING - 400A TP MCCB With microporcessor based LSIGN Protection - 2 Nos. 125A TP MCCB With microporcessor based LSIGN Protection - 1 Nos. 250A TP MCCB With microporcessor based LSIGN Protection - 1 Nos.

Supply, erecting, testing and commissioning of Hostel Building Power Panel . All incomer fedder shall be With ON, OFF & Trip Indication. All the components shall be housed in a common cubical made of 16 swg. M.S.sheet. The panel shall be powder coated of approved colour both inside & out side. The panel shall have both bottom & top cable entry provisions and panel shall be mounted on Pedestal of 300 mm height with necessary accessories etc completed.Panel Shall be Indoor type With IP 43 Protection & Form-3B Sepration. Panel Shall Be As Per IEC 61439. As per CSR spacification (SW-MCB,SW-MCCB, SW-ACB,CP-BB,CP,WG MA/BW,WG-MA CON ) INCOMER - 400A TP MCCB With microporcessor based LSIGN Protection - 01 Nos. & 1 Sets of 500 Amps. Aluminium Bus bars with colour coded heat shrinkable PVC sleeves, 1 Set of RYB indicating lamps with individual MCB's, 1 Nos of Multifunction Meters . All Incomer shall be with surge protection. OUTGOING - 63A TP MCB, C Curve - 18 Nos.

Supply, erecting, testing and commissioning of Hostel Building Lighting & Utility Panel . All incomer fedder shall be With ON, OFF & Trip Indication. All the components shall be housed in a common cubical made of 16 swg. M.S.sheet. The panel shall be powder coated of approved colour both inside & out side. The panel shall have both bottom & top cable entry provisions and panel shall be mounted on Pedestal of 300 mm height with necessary accessories etc completed. Panel Shall be Indoor type With IP 43 Protection & Form-3B Sepration. Panel Shall Be As Per IEC 61439. As per CSR spacification (SW-MCB,SW-MCCB, SW-ACB,CP-BB,CP,WG MA/BW,WG-MA CON ) INCOMER - 125A FP MCCB With microporcessor based LSIGN Protection - 02 Nos 125A FP Autotransfer Switch - 01 Nos 1 Sets of 250 Amps. Aluminium Bus bars with colour coded heat shrinkable PVC sleeves, 2 Set of RYB indicating lamps with individual MCB's, 2 Nos of Multifunction Meters . All Incomer shall be with surge protection. OUTGOING - 10A SP MCB B Curve - 2 Nos. 25A/32A TP MCB C Curve - 19 Nos. 40A TP MCB C Curve - 3 Nos.

Supply, erecting, testing and commissioning of Hostel Building DG Set Panel . All incomer fedder shall be With ON, OFF & Trip Indication. All the components shall be housed in a common cubical made of 16 swg. M.S.sheet. The panel shall be powder coated of approved colour both inside & out side. The panel shall have both bottom & top cable entry provisions and panel shall be mounted on Pedestal of 300 mm height with necessary accessories etc completed. Panel Shall be Indoor type With IP 43 Protection & Form-3B Sepration. Panel Shall Be As Per IEC 61439. As per CSR spacification (SW-MCB,SW-MCCB, SW-ACB,CP-BB,CP,WG MA/BW,WG-MA CON ) INCOMER - 315A TP MCCB With microporcessor based LSIGN Protection - 01 Nos 1 Sets of 630 Amps. Aluminium Bus bars with colour coded heat shrinkable PVC sleeves, 1 Set of RYB indicating lamps with individual MCB's, 1 Nos of Multifunction Meters . All Incomer shall be with surge protection. OUTGOING - 125A TP MCCB With microporcessor based LSIGN Protection - 4 Nos. 63A TP MCB C Curve - 01 Nos

Supplying, installing and testing UTP connector (RJ-45) as per specification No. WG-NAS/UTPC.

Supplying and installing cat-6 cable suitable for networking as per specification no. WG-COC/NC

Supplying and fixing 1 m UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

Supplying and erecting 5m HDMI cord low voltage grade minimum 4k compliant to be laid in provided conduits with male/female 19 pin HDMI connectors complete.

Supplying and fixing 9U wall mount rack (Dimension-DxWxH – 500x600x500 mm) as per specification No. WG-NAS/RAK

Supplying, fixing, and configuring 24 ports, POE switch in provided rack as per specification No. WG-NWC/ENS

Supplying and fixing 24 port patch panel with tool-less keystone jacks in provided U Rack complete as per specification no. WG-NAS/PP

Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Supplying & erecting of High definition 2 Megapixel IP IR Dome Camera with following features - Image Sensor : minimum 1/2.8" Progressive Scan CMOS, Video Resolution : minimum 1920 x 1080 Video Compression : H.264, H.265 or higher, at least Three individually configurable stream, Frame rate : minimum 25 fps at all resolutions, WDR : minimum 120 dB Wide Dynamic Range, ONVIF profile conformant, minimum IR distance : 30m, Lens Type : 2.8/4/6 mm Lens, fixed focal,Field of View : 2.8 mm, horizontal FOV 107°, vertical FOV 57°, diagonal FOV 129° 4 mm, horizontal FOV 86°, vertical FOV 47°, diagonal FOV 102° 6 mm, horizontal FOV 55°, vertical FOV 29°, diagonal FOV 65° Lux sensitivity - minimum 0.2 Lux at color, minimum 0.05 Lux at Black & White, 0.0 Lux (IR) Night Vision Distance minimum IR - 30m. Camera minimum Adjustment Angles - Pan : 350°, Tilt : 72°, Rotate : 350°.Power Supply : Support 12VDC & PoE,IP67, IK10 - Vandal Resistant. Built in micro SD/SDHC/SDXC card slot of minimum 128 GB, Built in microphone. minimum Input/Output - Audio in × 1, Audio Out × 1, Alarm in × 1, Alarm Out × 1. Image Settings : Rotate mode, saturation, brightness, contrast, sharpness, gain, white balance. Image Enhancements : Day/Night-Auto (ICR)/Color/Black & White, 3D Digital Noise Reduction, Automatic White Balance, Automatic Gain Control, Backlight Compensation, Highlight Compensation.

Supplying, installing, testing & commissioning of minimum 4 Ch. Network Video Recorder (NVR), suitable for 2 MP cameras only with HDMI/VGA outputs provided HDMI output of 4K resolution or VGA output with output up to 1920x1080. Support H.265 or higher, H.264, MJPEG, Incoming Bandwidth 40Mbps with minimum 1 SATA ports, ANR Technology, 1 SATA interfaces for 1 HDDs and capacity of each HDD up to 8 TB, Min. 02 USB port, RJ-45 10 /100 Mbps self-adaptive Ethernet interface, support multi brand network Cameras, ONVIF conformance, Multiple network monitoring: Web viewer . support protocol TCP/IP, DHCP, DNS, DDNS, NTP, SADP, SMTP, NFS, iSCSI, UPnP™, HTTPS. RoHS, UL, CE, FCC certified.duly erected in provided U Rack with wiring connections, tagging and programming etc complete as per specifications no. CCTV-NVR

Supplying & erecting 2TB internal Surveillance HDD suitable for SATA Port of NVR, interface transfer rate 6 GB/S, maximum sustained transfer rate 145MB/Sec to 180MB/S. Drive bay supported 08, Cameras supported up to 64, Cache (MB) 64, Load/Unload Cycle -3000000, Work Load Rating per Year 180TB, MTBF 1000000 Hrs. HTTPS. RoHS, UL, CE certified, duly erected in position in provided NVR as per specification no. CCTV-HDD

Supplying & erecting 22"-24" professional LED Monitor with 1920*1080 (Full HD) Display, suitable for 8 channel NVR and following features Brightness: minimum 250 Cd/m2 Contrast Ratio: minimum 1000:1 Viewing angle: 178/178 deg. Response time: maximum 8 ms Inputs: HDMI, VGA, BNC,USB, Audio In, Built-in speakers maximum 2 W, Suitable to operate on 100-240 V 50 Hz AC supply and 24/7 Duty Cycle duly erected on wall or table top with standard accessories like wall mount stand and wiring connections etc complete as per specifications no. CCTV-MON

SITC of Electric Traction Passenger Lift with · Rated capacity :- 10 Passenger/680Kg · Floors :- G+7 floor (8 Stops/8 Landings) · Travel :- 21 to 29.4 mtrs · Location of Lift Machine:- MR/MRL · Rated speed :- 1.5mps VS · Car/Landing door clear opening of 800 mm wide x 2000 mm high · Clear Car size of 1300mm wide x 1350mm deep x 2250mm high · Lift shaft available having clear size of 1800mm wide x 1700mm deep, 1500mm Pit depth, 4200mm Overhead. · Doors type :- COPO/TOPO Doors with frame · Lift Machine of Gearless PMSM of suitable kW with duty cycle of minimum 120 starts/hr (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory), with Traction pulley, OSG, electromagnetic brakes, entire assembly mounted on adequate size girders duly fixed on LMR floor/ shaft walls complete with main/diverter traction sheaves, suspension wire ropes/belts of adequate size & strength.made from SS 304 grade solid(non-cladded) sheet of 1.5mm thick in hairline finish for car and all landing doors with SS door architraves/frames The lift doors shall have minimum 1 hour fire rating (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory). · Lift car enclosure made from · Minor civil work such as alteration work if any necessary for erection of landing door frames and it's accessories e.g. sill, header, hole pass etc complete with plaster finish, civil work for erection buffers, erection of lift machinery, adequate size core cuts if required & scaffolding for erecting guide rails, providing and fixing steel girders/RCC work having adequate strength for mounting and hoisting lift machine etc. complete as per specification no. LFT.· Other mechanical parts such as 'T' section adequate size guide rails for car & counter weight with brackets fasteners, counter weight frame with necessary blocks, buffers with necessary support arrangement, MS pit ladder etc. erected with necessary steel work.SS 304 grade solid (non-cladded) sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. The lift car interior design shall be done as per the directions of engineer in charge. · COP with SS face plate having metallic push buttons with Braille code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with / without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor. · LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings.· Lift controller of simplex full collective based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port. The controller shall have necessary protections such as overcurrent, overvoltage, over speed, overheat for all devices including lift motor and travel direction protection, protection for phase loss at input or output etc. ,various operation modes such as maintenance, change direction by attendant, full load bypass, VIP call operation, self levelling operation, call cancel facility, auto return to home landing, fireman evacuation operation, earthquake operation, door open/close operation from COP etc. The system can record information for minimum 30 latest faults, with real-time clock management and handheld keypad with LCD screen for view and setting of parameters, The control panel duly wired with proper size & strength, copper wire for power & control circuit, with provision for addition of floor/control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class. · ARD complete with necessary SMF VRLA batteries. · Fireman controller having fireman switch at fire Landing. · CCTV surveillance system comprises of 2nos minimum 2.0MP FHD IP based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on Lift machinery & controller with NVR kept in LMR/FCC with HDR data backup for min. 90 days with min. 20" FHD TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge.· General: - Job includes entire procedure of obtaining all necessary erection permissions & "License to Work the Lift" from Electrical Inspector(Lifts) with submission to the Engineer In Charge. · The above rate includes Fully Comprehensive AMC for one year from the date of commissioning.

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 2 core 2.5 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & marking SPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking DPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & commissioning 2 pole RCCB 16/25A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 6 ways (6 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB

Supplying, erecting & marking FPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & commissioning 4 pole RCCB 40A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame.

Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 4 module duly erected.

Supplying and erecting bulk head LED fitting max. 10W with high transitivity diffuser with system lumens output of min. 1100 lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., THD<10%, p.f. >0.95, operating range of 140-260V, in built surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, IP66, IK09 rated on provided PVC Block / wooden board with 3 years warranty.

Supplying and erecting Ceiling rose / Batten holder / Slanting holder / hanging cord switch / hanging bell push / pendant holder bakelite base 6A. erected on filled polypropylene board or polished double wooden block/ PVC junction box.

Providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Supplying and erecting annealed bare copper wire of high purity of required sizes used for earthing on wall with necessary copper clamps fixed on wall/cable/conduit with screws complete.

Providing & erecting 6 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Supplying and erecting integrated LED street light fitting 40 to 50W IP65 & IK08 class having single piece pressure die-cast aluminium housing, having system lumens output of Min. 4400 Lumens, min. efficacy of 110 lumen/W, CRI>70, CCT upto 6500K,THD<10%, p.f. >0.95, operating range of 140-270V, inbuilt surge protection of 10 kV, Life class of 50,000 Hrs. at L70B50, including driver complete with 3 Years warranty as per specification No FG-ODF/FLS2.

Providing and erecting galvanised 1000mm single arm sword type bracket with FRP dome and ball as per specification no. OH-PL/PBKT

Providing and erecting galvanised 1000mm double arm sword type bracket with FRP dome and ball as per specification no. OH-PL/PBKT

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 25 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying and erecting PVC insulated PVC round sheathed 2.5 sq.mm (50 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV

Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Supplying, erecting & marking SPMCB 0.5A to 5A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 6m to 8m high octagonal /conical GI pole).

Providing pipe type earthing with 40mm. dia. G.I. pipe or 20 mm dia. G.I. Rod complete with all materials testing and recording the results as per specification no. EA-EP

Providng earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Supplying, erecting, testing and commissioning 22KV HT metering cubical (compact type) approved by MSEDCL / licensee fabricated with 2 mm (14 SWG) M.S. sheets with supporting angle, painted with powder coating / epoxy paint of required shade, copper bus bar size 25 x 6 mm, heavy duty mechanical lock, with counter meter for measuring no. of times the opening of meter door, top side cover (CT, PT cover) interlock with meter door, epoxy casted 3 nos. CT having required ratio between 5/5A to 25/5A, VA 10 or 15, Class 0.5S, epoxy casted 3 nos. PT having ratio 22000/V3/110/V3 VA 50, Class 0.5 suitable for provided trivector meter, and provision for incoming and outgoing cables complete duly tested by licensee with necessary test certificates and erected on provided plinth/ cc foundation.

Supplying, installing, testing and commissioning SF 6 Insulated 22kV, 630A, 16kA/3sec, 3 way outdoor, extensible motorised SCADA compatible RMU, internal arc tested as per electric supply company specification consisting of 2 nos. feeder with 2 LBS and 1 no. feeder with 1 VCB. compliant to IEC 62271 -100, 200 and 102, as per specification no. SW-HTS/RMU SCADA

Supplying, installing, testing & commissioning 3 phase, 22/0.433 kV, 50 Hz., 1000 kVA, Mineral oil immersed and naturally cooled outdoor type, Copper wound ,without gas cushioning ,hermetically Sealed transformer, delta/star connected with additional neutral brought out on load side, temperature rise should not exceed 45℃ by thermometer in oil and 50℃ by the resistance method in winding at full load rating, using type A winding insulation (kraft paper) with HV tapping (with on load tap changer) on load +5 to -15 in steps of 2.5%, with standard accessories complete with test certificate with losses below 2930 Watts at 50% load, 8085 Watts at 100% load as per IS:1180 (part 1) : 2014 with necessary permissions of Electrical Inspector, as per specification no SS- TR-SL.

Supplying , erecting & terminating XLPE insulated, galvanised steel formed wire armoured (round) cable 22 kV(E), 3 x 300 sq. mm. aluminium conductor laid in provided trench / pipe as per specification no. CB-HT (Note:- For round wire armouring increase rate 22 kV, 33kV (E)/(UE) by 31% )

Providing and erecting Heat shrinkable outdoor termination kit for 11 kV (UE)/ 22 kV ( E ) XLPE HT cable 3x240 to 400 sq. mm. with necessary material as per specification no. CB-JT/HT

Supplying & erecting cast iron cable indicator plate buried along with route of cable for PVC / XLPE armoured cable as per specification No. CB-CIP

Supplying, installation and testing of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete, and recording the results Specification no. EA-MOBI

Supplying and erecting GI strip of high purity required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint with joints required. As per specification no EA-EP.

Providing printed instruction chart for treating persons suffering from electric shock, printed in English & Marathi and duly laminated complete.

Providing pair of duly tested rubber hand gloves as per IS :47705 suitable for working up to 22 kV supply complete.

Supplying standard first aid box with necessary antiseptic cream, medicine for use on wounds due burn, crepe bandage, gauge bandage, medicated ready to use bandage (Band-Aid) adhesive tape for medicinal use, scissors, anti-septic solution, etc. (All above contents shall be of standard makes)

Supplying and fixing PVC synthetic elastomer electrically insulating mat with class A insulation conforming to IS: 15652 – 2006 having 2 mm thickness up to 3.3 kV

Supplying, erecting, testing and commissioning of diesel generating set with alternator of 200 kVA output continuous rating, 3 Phase, 415 V, 50c/s 0.8 p. f. A.C supply, a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours, along with standard accessories, self-excited, self-regulated, screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation +/- 5 %, with performance class G2 and maximum fuel consumption 34.40 Ltr/hr @75% loading. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads with standard control panel comprising meters, switchgears, indicators connected with suitable wires/cables, the complete set enclosed in composite Acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA Sheet, sound absorbing material to restrict sound level up to 75 dB(A) at 1.0 m, provided with first filling of oil, diesel not less than 300 Ltr etc. on provided M20 Grade CC Foundation as per specification no. GEN-DG

Supplying, erecting, testing and commissioning of microprocessor based AMF panel suitable for diesel generating set of above 180 kVA up to 200 kVA capacity Three phase, 415 Volts, 50Hz A.C. with all standard features, safeties etc as per specification no. GEN-AMF.

Excavating hard Rock or bituminous road by chiselling for preparing pit for pole / stay/earth plate / for laying cable/ pipe & clearing the site by removing debris & making the site as required complete.

Supplying and erecting fencing of section having size 2450 mm in height from ground level and 1200 mm width with angle iron frame work erected in CC foundation and painted complete as per specification no SS-AS/FSG

Supplying and erecting 50 x 50 x 6 mm angle iron as corner support 2m long fixed at the middle of the fencing frame and the other side inclined at 30 degree angle, in cement concrete foundation of 15 x 15 x 40 cm complete duly painted with one coat of red oxide and two coats aluminium paint complete.

Supplying and erecting double leaf hinged door each 1500 mm in width x 1850 mm in height using B class, GI pipe with angle iron supports, chain link wire mesh (jali) complete supported on channel iron, erected in foundation, and painted complete as per specification no SS-AS/DLD

Providng earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Supplying, installation and testing of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete, and recording the results Specification no. EA-MOBI

Supplying and erecting GI strip of high purity required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint with joints required. As per specification no EA-EP.

Making cement concrete foundation in 1:3:6 cement concrete, (20 to 25) mm. stone metal duly plastered with necessary curing for complete. (pole muffing or any other purpose).

Please Enable Macros to View BoQ information