REPAIR AND MAINTENANCE TO EXTERNAL SERVICES LIKE PATHS HARDSTANDING COMPOUND WALL FENCING AND CERTAIN MISC B R WORKS AT VRDE AHMEDNAGAR 06

Amount

Dismantling floor, health or wall tiling including cement mortor bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified and directed.

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness below or above ground level unreinforced all as specified and directed.

Demolition of reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness below or above ground level all as specified and directed.

M&L for 75 mm thick PCC (1:2:4) type B2 (using 40 mm graded stone aggregate) as in hard standing finished even and smooth without using extra cement complete all as specified and directed.

M&L for hardcore of broken stone or boulders of guage exceeding 63 mm but not exceeding 100 mm deposited, spread and levelled in layers not exceeding 15 cm thick watered and rolled/rammed to a true surface complete all as specified and directed.

Supply only broken glass beads of size 60 to 80 mm (approx) & mixed with hardcore below concrete all as directed by Engr-in-Charge.

M&L for 75 mm thick PCC (1:3:6) type C2 (using 40 mm graded stone aggregate) as in plinth protection finished even and smooth using extra cement all as specefied and directed.

Forming contraction (Dummy) joints 65 mm deep x 10 mm wide, filled with sealing compound grade 'A' all as specified and directed.

M&L for 75 mm thick PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) as in sub base of floor finishes all as specified and directed.

M&L for 25 mm thick PCC (1:2:4) type B1 (using 20 mm graded stone aggregate) as in floor finishes all as specified and directed.

M&L 20 mm thick sand cushion spread, levelling in layers not exeeding 25 cm thick including watering etc complete all as specified and directed.

M&L machine pressed precast concrete interlocking paver block any shape and size confirming to IS - 15658-2006 with grey cement and pigment of 60 mm thickness M-35 grade complete all as specified and directed.

M&L for Reinforced cement concrete nominal mix 1:1.5:3 type A1 (using 20mm graded stone aggregate) as in chajjas complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors/terrace etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

Excavation in post holes each not exceeding 0.50 cum getting out, returning filling and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm, watering and removing surplus soil to a distance not exceeding 50 mtr and making good surface in hard/dense soil complete all as specified and directed.

Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation for manholes etc not exceeding 10 sqm on plan and not exceeding 1.5 m deep and gettign out in hard/ dense soil all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming layers not exceeding 25 cm thick soil all as specified and directed.

Removing of surplus excavated soil to a distance not exceeding 50 mtrs and deposited where directed at a level not exceeding 1.5 mtr above the starting point all as specified and directed.

M&L for PCC (1:4:8) type D2 (using 40 mm graded stone aggregates) as in foundation filling and mass concrete all as specified and directed.

M&L form work to sides of concrete foundations, footings, rafts, plinth beams etc of rough finished surfaces of flat all as specified and directed.

M&L form work to sides of concrete columns, pillars etc of fair finished surfaces of flat all as specified and directed.

M&L for reinforced cement concrete nominal mix 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in foundation, footings foundation beams, plinth beams, bases for columns etc all as specified and directed.

M&L for reinforced cement concrete nominal mix 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in columns, pillers, piers, posts and struts etc all as specified and directed.

M&L for granite tile/slab of size 600 x 300 x 12 mm thick machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including nosing, grinding and polishing complete over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

S&F rolled mild steel joist, channel, angle or tee sections fixed without connected plates etc quality confirming to Fe-410-W (gde E-250) quality - A all as specified and directed.

S&F rolled mild steel framed work as in doors or gates of angle or other section confirming to Fe-410 S with gusset plates, rails braces etc complete drilled and fixing of steel sheeting or other covering and hanging and fixing complete all as specified and directed.

S&F SS letters of size exc 35cm and nexc 40cm in height and 40 to 70mm in width, fixed on coloured acrylic sheet 9 to 10mm background with approved adhesive including providing coloured LED lights of suitable wattage all as directed by Engineer-in-Charge. NOTE:- Unit rate quoted by Contractor shall deemed to be inclusive cost of LED lights, Internal electrification work such as provision of suitable size cable and adoptors for LED lights, drilling holes in walls/granite at locations to fix the letters all as directed by EIC.

M&L precast reinforced cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in 35 mm thick jallies or louvers including all mouldings complete and set in cement mortor 1:4 all as specified and directed.

M&L for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick or concrete surfaces on CM 1:6 finished the surfaces even and fair without using extra cement all as specified and directed.

M&L for preparation of newly plastered surfaces of any description and applying two coats of cement based paint over a coat of chalk whitening primer on wall surfaces all as specified and directed.

M&L mild steel TMT bars 10 mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90 mm dia or securing with clips all as specified adn directed.

M&L mild steel TMT bars 5 mm dia & over upto and including 10 mm dia cut to length, bent to shape required as in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.90 mm dia or securing with clips all as specified and directed.

Supply only chain link MS galvanised fencing any size or type all as specified and directed. Note : Dia of chain link wire & size of mesh shall be as directed by EIC. Weight of chain link shall be measured at site & shall be paid accordingly.

Fixing only chain link fencig including line wires, any mesh, size and type to any type of standards, rails, straining bolts etc including provision of binding wire all as specified and directed.

Demolition of brick work or stone/ boulder masonry built in cement mortor including all quoins arches, pillers etc but excluding ashlar facings and dressed stone work all as specified and directed.

M&L for walling of randam rubble uncoarsed, well bonded and solidly hearted built in cement mortor 1:6 complete all as specified and directed.

M&L for walling of random rubble uncoursed, well bonded and solidly hearted built in cement mortor 1:6 but except stone all as specified and directed.

M&L keyed pointing to random or polygonal rubble uncoursed or brought upto course in cement mortor (1:4) all as specified and directed.

Dismantling mild steel work, wire and coil work of any description not otherwise provided for all as specified and directed.

S&F mild steel angle posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc, flat iron fillets (for securing wire etc, and similar work confirming to Fe-290 Grade E-165 all as specified and directed.

S&F in repairs galvanishd 2 strand steel barbed wire 2.24 mm dia of barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to angle fencing above compound wall and any type including securing or tying at crossing with and provision of galvanished mild steel wire staples or stee pins etc all as specified and directed (each line or wire to be measured).

S&F in repairs galvanishd concertina coils, 1050 mm dia (50 spirals per coil) weight approx 14.50 Kgs (+-5%) expandable 10-12 mtrs consisting of 2.60 mm dia heavy galvanised high tensile spring steel wire as per IS-4454, barb (barb length 24+1 mm pitch between two barbs 35+1 mm ) made of 0.50 mm thick low carbon heavy galvanised cold rolled steel sheets as per IS-513, heavy duty steel clip as per IS-2062 all as specified and directed.

M&L for preparation of newly prepared steel surfaces of any discription over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as per specified and directed.

M&L for 18-20 mm thick granite (any type & any colour ) work (table rubbed and polishing) in vertical surfaces such as dado, skirting etc including 10 mm thick backing coat in CM (1:4) including admixture of pigment to match with shade of granite all as specified and directed.

S&F 10 mm thick toughend glass at locations including accessories required for fixing all as directed by EIC.

Smruti Construction

ASHUTOSH BUILDERS

DESIRES ENGINEERS &CONTRACTORS

Siddhant Hukumchand kumath