PETTY REPAIR FOR ATTENDING DAY TO DAY EM EXTERNAL WATER SUPPLY COMPLAINTS AT PARADE CAMP AREA MALL ROAD POLO ROAD CHURCH ROAD STN ROAD URBAN VILLAGE MANEKSHAW MARG OLD NEW APS COLONY SANJAY VIHAR AND ALLIED AREA IN THE AREA OF AGE U WATER SUPPLY NO

Amount

Labour only for attending day to day external water supply complaints of all nature i.e leakage in water supply pipe lines , fitting/fixture, over flow of overhead tank, no water supply,taking out water water from trenches during repair including noting the complaints in complaint register complete all as specified and as directed. (Any material required for attending complaints shall be measured and paid separately under respective item herein after) Note :- quoted rates include notes mentioned at srl No. 1.10 to 1.90.

Notes for item No. 1.00 & 2.00 The complaints shall be attended and the defects shall be rectified by a team of expert and experienced electrician/plumber as applicable assisted with adequate No of helpers complete all as specified and as directed

The complaints shall be attended and defect shall be rectified within 08 hrs commencing from date and time of notifying the complaint failing which a penalty @ Rs 500/- per complaint per day (08 hrs) shall be levied upon/imposed on the contractor and recovery shall be made from contractor's dues.Contractor rep shall be available wef 0800 hrs to 2000 Hrs to receive and notify the complained

In case, after checking and attending the defect, it is not possible to rectify the defects within 08 hrs the facts shall be brought to the notice of Engineer-in -charge by the contractor /his rep . If Engineer -in-charge is satisfied with contractors view, no recovery will be made.

while attending the complaint of water supply /Electric supply if earth work is required then the same shall be measured and paid seperately under appropriate item of Sch 'A' . However no extra payments shall be made for dewatering.

Cutting of GI pipe in position and threading is also deemed to be included in the job rate (Fitting and fixtures will be measured and paid separetely under respective item of Sch A.

All T & P as well as dewatering motor single phase of 3HP with including 100 mtr cable, required for attending the complaints shall be provided by the contracor.

The pipe fitter shall always be in possession of die set complete with cutters , Taps , Pipe wrench, Chain wrench,Caulking tools, Complete set of spanners and ladders etc…, as required at site.

The elecrician shall always be in possession of all Electrician tools , LT Megger, Earth tester , Multimeter , Crimping tool, insulation tape, Hand gloves etc required at site.

Supply the following items

PTMT stope cock 15 mm dia

Tank nipple 20 mm dia

Supply only of the following items :-

Supply only GI Socket Med grade ISI Marked of following sizes ;-

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

80 mm bore

Supply only GI Elbow Med grade ISI Marked of following sizes : -

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

80 mm bore

Supply only GI Union Med Grade ,ISI marked of following Sizes:-

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

80 mm bore

Supply only GI Nipple of different length as per requirement, both end screwed Medium Grade, ISI marked of following sizes:-

15 mm bore

20 mm bore

25 mm bore

40mm bore

50mm bore

Supply only PVC 'L' type Holder suitable for Aluminium rod,Float Ball etc complete all as specified and as directed byof following Sizes:-

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Supply only GI Reducing socket medium grade ISI marked of the following sizes :-

25 mmx15mm bore

20mmx15mm bore

25 mm x 20 mm bore

50 mmx 40mm bore

40 mmx 20mm bore

40 mmx 25mm bore

50mmx 25mm bore

Supply only GI Tee Med grade ISI Marked of following sizes : -

15mm x15mm x15mm

20 mm x 20 mm x 15 mm

20 mm x 20 mm x 20 mm

25 mm x 25 mm x 25 mm

25 mm x 25 mm x 15 mm

25 mm x 25 mm x 20 mm

40 mm x 40 mm x 40 mm

40 mm x 40 mm x 20 mm

40 mm x 40 mm x 25 mm

50 mm x 50 mm x 50 mm

50 mm x 50 mm x 40 mm

50 mm x 50 mm x 25 mm

50 mm x 50 mm x 20 mm

Supply only GI solid plug heavy duty ISI marked of following sizes

15mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Supply only Lead pig bar

Supply only spun yarn

Supply only Nuts ,Bolts and Washers 25 to 150 mm long of 6 to 20 mm dia

Supply only 3mm thick rubber gasket

Supply only lead wool

Supply only PTMT float valve with epoxy coated aluminium rod and high density plastic ball of following sizes complete all as specified and as directed

15mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Supply only gun metal gate valve with iron wheel head screwed both ends for iron pipe , ISI marked , as per IS : 778 of following sizes complete all as specified and as directed

15mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Testing of drining water collected from local source (bore wells /shallow wells in the area of AGE(U) W/S No.II and submission of detailed test report to the office of Engineer-in-Charge. (i) Carrying out minimum essential testing of water as per IS 10500-2012 mandatory for chemical colour, odour, taste, turbidity, PH value, TDS total hardness, iron, chloride, fluoride and residual free chlorine and Bacteriological total coliform organisms per 100 ml (MPN) and E Coli in 100 ml) with specific recommendation regarding suitability of water for drinking purposes. (ii) Collection of water from[ different sources of water ie. Sump, bore wells & shallow well in a sterilized bottle and testing in NABL Approved laboratory as mentioned in specification Note :- Rate Quoted shall also deemed to be included for the followings:- (i) Cost of sterilized bottle as required. (ii) To and fro transportation charges for collection of samples from source (sump, bore & shallow wells)

Excvation in trenches not exc. 1.5 mtr wide and not exc 1.5 mtr deep for pipe line in soft/loose soil, getting out and levelling of bottom surface to required complete all as specified and as directed

Returning filling, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick complete all as specified and as directed

Removing excavated material from site to a distance not exc 50 m away and depositing where directed not exc 1.5 meters above the starting point complete all as specified and as directed

Surface dressing of uneven surfaces of the natural ground, rough excavated surfaces and filled area where ordered shall be trimed to an even surface horizontal or slopping, by removing vegetation and by scrapping high patches and filling low patches with the scrapping soil to given an even and neat look to the site. depth of cutting not exceeding 15 cm. complete all as specified and as directed

Supply only 15 mm bore Bib tap standard of PTMT any colour high pressure screwed for male/ female treaded, for UPVC pipe of size 15mm bore complete all as specified and as directed

Labour work required for taking out suction pipe 80 mm to 200 mm bore from sump of any capacity, dismantling of foot valve screwed / flanged type, and relowering after refixing in position the same duly cleaned / minor repair if any required such as replacement of rubber gasket/ lifting bolts & nuts including making thread for the suction pipes off sizes etc complete all as required and as directed

Supply only gland packing of any size

Supply only 'stem' made out from SS (all as per sample) of sluice valve of size as under : -

80 mm bore

100 mm bore

150 mm bore

200 mm bore

Supply only 'stem nut' made out from stainless steel suitable to match with existing sluice valve of sizes as under : -

80 mm bore

100 mm bore

150 mm bore

200 mm bore

Supply only 'gland plate' made out CI, suitable to match with existing sluice valve of sizes as under : -

80 mm bore

100 mm bore

150 mm bore

200 mm bore

Taking up or down steel tubing with connection including cleaning for removal complete all as specified and as directed of the follwing sizes :-

15 mm dia

20 mm dia

25 mm dia

40 mm dia

50 mm dia

80 mm dia

Relaying/refixing only jointing and testing of old GI pipes including cleaning completely in trenches as directed (serviceable pipe shall be picked up from item No 9 here in before ) for the following sizes :-

20 mm dia

25 mm dia

40 mm dia

50 mm dia

80 mm dia

Supply & fixing of GI pipe medium grade ISI marked including all fittings in old/new position as in walls and ceilling complete all as specified and as directed of following sizes :-

15 mm dia

20 mm dia

25 mm dia

40 mm dia

50 mm dia

Supply & fixing of GI pipe medium grade ISI marked including all fittings in old/new position as in trenches complete all as specified and as directed of following sizes :-

15 mm dia

20 mm dia

25 mm dia

40 mm dia

50 mm dia

80 mm dia

Labour for cutting and screwing existing steel tubing for alteration or addition complete all as specified and as directed of the following sizes :-

15mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Supply only cast iron/ DI fitting for flanged spigot and socketed pipes such as bends , reducer, tee pieces , tail pieces , collar, cross , caps & plug upto 150mm bore

Taking up cast iron/ductile iron water mains including all fitings with spigot and socket ends and lead joint including burning out joints and removing lead of size

100 mm bore

150 mm bore

200 mm bore

250 mm bore

Relaying/refixing of pipe CI/DI pipes after cleaning from inside with suitable chemical and rodding complete all as specified and as directed of fwg dia :-

100 mm bore

150 mm bore

200 mm bore

250 mm bore

Supplying ,laying ,jointing ,testing and commissioning of DI pipe as per IS 8239 class K-7 with in side cement mortar lining with spigot and socketed end laid in trenches complete with rubber gasket joint complete all as specified and as directed at site for the following sizes:-

100 mm bore

150 mm bore

200 mm bore

250 mm bore

Supply & fixing UPVC pipes of pressure rating of 10Kg/CM square fixed complete to walls , ceiling, floor or in trenches any types of pipe including fittings & jointing to the existing of following sizes

75/80 mm dia

100/110 mm dia

150/160 mm dia

Supply & fixing for mild steel work for tank cover/valve pit cover etc made of MS angle /flats/channels etc including cutting of top and botttom to shape as directed,drilling holes & welding work etc and similar works confirming Fe-290,Gde E-165 complete all as specified and as directed.

M&L for painting on steel and iron surfaces with one coat of synthetic enamel paint as per existing colour scheme or pattern after preparation of old painted surface of any description over 10cm in width or girth complete all as specified and as directed

Timer switch dial type 24 hours Make L&T up to 16 Amps

Supply, fixing, jointing & testing cast Iron Sluice Valve of sizes as under , ISI Marked, flanged ends drilled pressure rating PN-1.0, PD Short body, Confirming to IS 14846 -2000, having stainless steel spindle with cast iron operation wheel at top including taking out unserviceable sluice valve and depositing to MES store yard complete all as specified and as directed. Note:- Flanged joints complete with jointing material shall deemed to be included in the unit rate of this item.

150 mm bore

200 mm bore

Material and labour for CI foot valve including nut and bolts washers and rubber 150mm dia confirming to IS-4038 complete all as specified and as directed

Labour only for attending of electric supply complaints of day to day maintenance of existing LT panels including connecting electrical accessories/ spares of water supply installation and electrical fitting & light, short circuits in pump house complete all as specified and as directed (any material required for attending complaints shall be measured & paid separately under respective item here in after)

An amount of Rs 60850.00 shall be deducted from BOQ on account of schedule of credit

somyaenterprises

MISHRA ELECTRICAL

Ayushmat Contractors

Rahul Enterprises