Provision of Sauna Bath, Steam Bath and Chiller Bath at PK Road colony and Balance work for Repairs to Engineering workshop, garages, out houses, road berms, manhole covers and drainage system at PK Road colony in the section of SSE/W/PG under ADEN/E-I.

Item Breakup - A-Schedule A

pattern. 17.0 SANITARY INSTALLATIONS DELHI DIVISION-ENGG/NORTHERN RLY Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with 17.1 manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 17.1.1 White Vitreous china Orissa pattern W.C. pan of Each 1 5781.35 5781.35 63 size 580x440 mm with integral type foot rests Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with 17.2 manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : 17.2.1 W.C. pan with ISI marked white solid plastic seat Each 2 5540.55 11081.1 64 and lid Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm 17.7 C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 17.7.2 White Vitreous China Wash basin size 630x450 Each 3 1913.75 5741.25 65 mm with a single 15 mm C.P. brass pillar tap Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, 17.10 including painting of fittings and brackets, cutting and making good the walls wherever required : 17.10.2 Kitchen sink without drain board 66 17.10.2.1 610x510 mm bowl depth 200 mm Each 2 4274.4 8548.8 17.35 Providing and fixing soil, waste and vent pipes : 17.35.2 75 mm diameter : 17.35.2.2 Centrifugally cast (spun) iron socketed pipe as Metre 10 1042.1 10421 67 per IS: 3989 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or 17.60 without vent arm complete, including cost of cutting and making good the walls and floors : 17.60.2 100 mm inlet and 75 mm outlet 68 17.60.2.2 Sand Cast Iron S&S as per IS- 1729 Each 3 1296.4 3889.2 18.0 WATER SUPPLY 18.7S C.P.V.C. PIPES Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing 18.7 the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.-Internal work - Exposed on wall 69 18.7.2 20 mm nominal dia Pipes Metre 100 325.1 32510 Providing and fixing G.I. pipes complete with G.I. 18.10 fittings and clamps, i/c cutting and making good the walls etc.-Internal work - Exposed on wall 70 18.10.1 15 mm dia nominal bore Metre 100 304.15 30415 DELHI DIVISION-ENGG/NORTHERN RLY Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls 18.11 etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 71 18.11.1 15 mm dia nominal bore Metre 100 485.2 48520 Providing and fixing G.I. pipes complete with G.I. 18.12 fittings including trenching and refilling etc.- External work 72 18.12.3 25 mm dia nominal bore Metre 150 417.95 62692.5 18.15S BRASS FITTINGS Providing and fixing gun metal gate valve with 18.17 C.I. wheel of approved quality (screwed end) : 73 18.17.1 25 mm nominal bore Each 3 532.35 1597.05 Providing and fixing uplasticised PVC connection 18.21 pipe with brass unions : Providing and fixing C.P. brass shower rose with 18.22 15 or 20 mm inlet : 74 18.22.2 150 mm diameter Each 2 190.1 380.2 18.31S C.I. SLUICE VALVES/ FIRE HYDRANTS & FIXTURES Providing and fixing G.I. Union in G.I. pipe 18.46 including cutting and threading the pipe and making long screws etc. complete (New work) : 75 18.46.1 15 mm nominal bore Each 5 262.3 1311.5 76 18.46.3 25 mm nominal bore Each 2 369.35 738.7 18.48 Providing and placing on terrace (at all floor Litre 6000 9.7 58200 levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking 77 arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 18.49S C.P. BRASS FITTINGS Providing and fixing C.P. brass bib cock of 18.49 approved quality conforming to IS:8931 : 78 18.49.1 15 mm nominal bore Each 2 434.2 868.4 Providing and fixing C.P. brass long body bib 18.51 cock of approved quality conforming to IS standards and weighing not less than 690 gms. 79 18.51.1 15 mm nominal bore Each 3 708.4 2125.2 19.0 DRAINAGE Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover 19.4 with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 19.4.1 100x100 mm size P type 19.4.1.1 With common burnt clay F.P.S. (non modular) Each 2 2453.55 4907.1 80 bricks of class designation 7.5 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with 19.6 stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 81 19.6.3 250 mm dia. R.C.C. pipe Metre 35 811.15 28390.25 DELHI DIVISION-ENGG/NORTHERN RLY Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (Zone-III) : 8 graded stone aggregate 40 mm 19.7 nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm 19.7.1 internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : 19.7.1.1 With common burnt clay F.P.S. (non modular) Each 1 11687.1 11687.1 82 bricks of class designation 7.5 26.0 NEW TECHNOLOGIES AND MATERIALS 26.73S PREFAB/PRECAST TECHNOLOGY Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/clerestory windows & desertory other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 26.86 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 83 26.86.5 Frame size 65 x 100 mm Metre 20 1000.15 20003 DELHI DIVISION-ENGG/NORTHERN RLY Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), 26.87 m i n i m u m compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 84 26.87.1 30 mm thick Sqm 10 3954 39540 Total 5556429.84