01. DEVELOPMENT OF THE RAJLA SHIVA TEMPLE, LOCATED IN KUDHANI BLOCK OF MUZAFFARPUR DISTRICT, FROM A TOURISM PERSPECTIVE.

BIHAR STATE TOURISM DEVELOPMENT CORPORATION LIMITED

Technical Sheet

Name of Work DEVELOPMENT OF THE RAJLA SHIVA TEMPLE, LOCATED IN KUDHANI BLOCK OF MUZAFFARPUR DISTRICT, FROM A TOURISM PERSPECTIVE. Cost of Work as per BOQ(Rs in Lakhs) 574.581 Time of Completion in months 12 ALL COLOURED CELL TO BE FILLED ACCORDINGLY

Sactioned Amount 62982000 Date of Sanction 2026-07-24T00:00:00Z Date of Tender 2026-06-27T00:00:00Z

Sl No. Items Requirement Cl. No. Name of the Contractor

Address of the Contractor

1 Registration No.

2 Bid Validity Bids shall remain valid for a period not less than 120 days after the deadline date. A Bid valid for a shorter period shall be rejected by the Employer as non-responsive 120 Days 15.1 Bid validity periods In days

3 Bid Security (A) Online mode i.e. internet payment gateway (credit/ debit card), Net Banking, NEFT/ RTGS 16.1 Amount To be entered (Rs in Lakhs)

(B) Unconditional bank guarantee from any scheduled Indian bank issued within the state in the format given (If issued from any bank outside state will be converted to any bank within the state before executing the agreement. Amount To be entered (Rs in Lakhs)

Bid Security Amount - (Rs. In Lakhs) 11.54 Bid Security Amount - Rs.

4 (i) Legal Status of Bidder. 4.3(a)

(ii) Place of Registration.

(iii) Principal place of Business

(iv) Power of attorney of signatory Bid Attached or Not 4.2(iv)

5 Total value of civil engineering construction work performed in last five years. 1. Annual Financial Turn Over usually not less than 50 % of the estimated annual payments under the contract (Rs in Lakhs) APPENDIX to ITB

2021-22 Amount To be entered (Rs in Lakhs)

Escalation Factor= 1.469

2022-23 Amount To be entered (Rs in Lakhs)

Escalation Factor= 1.36

2023-24 Amount To be entered (Rs in Lakhs)

Escalation Factor= 1.26

2024-25 Amount To be entered (Rs in Lakhs)

Escalation Factor= 1.166

2025-26 Amount To be entered (Rs in Lakhs)

Escalation Factor= 1.08

6 Work Experience of Similar nature Satisfactory completed atleast one similar work of value not less than 50 % of estimated value of contract (Rs in Lakhs) 4.5 (b) Amount To be entered (Rs in Lakhs)

7 Minimum Quantities of work done as prime contractor in any one year during last five years. Items Unit Total Quantity 4.5 ( c )

Brick Work cum 144.89 Value to be entered in unit cum

Electrical Works Rs. 3161224.88 Value to be entered in Rs.

PHE Work Rs. 1103945.18 Value to be entered in Rs.

PCC&RCC cum 517.24 Value to be entered in unit cum

Steel MT 46.88 Value to be entered in KG

Flooring Work. (Any Stone, Granite, Kota, Sand Stone etc.) sqm 1403.2 Value to be entered in unit sqm

8 Bidding Capacity More than the total Bid value of present work = A*N*3-B=Rs. ____.Where A = Maxm. Value of work executed in any one yr during last 5 yrs. N= Nos of years for completion of works. B=Value of existing commitments & ongoing works to be completed in period (Rs in Lakhs) 4.4

9 (a) Existing commitments and ongoing works Amount To be entered (Rs in Lakhs)

(b) Work for which Bid already submitted Amount To be entered (Rs in Lakhs)

10 Availability of key items of Contractor's Equipment Type of Equipment/Maximum age No. Required Nos. Max. Age Page-17 Nos./ Max. Age

Front end Loader 1 5

Plate Vibrator 2 5

Niddle Vibrator 2 5

Water tankar 2 5

Steel shuttering 2500sft 5 to 7

Concrete Mixture 1 5

11 Key Personnel Personnel/Qualification/Contract Package Size (Rs. 02 to 10 Crore) Page-18 Name of the Personnel and Experince in years

Site Engineer/ B.E. Civil + 07 Years Exp. (3 years in Building Construction) or retired A.E. 1 No.

Plant Engineer/ B.E. Civil + 05 Years Exp. or Dip. Electrical + 07 Years Exp. or Retired J.E. 1 No.

Site Supervisor/ Fresh Graduate in Civil or Diploma Civil + 03 Years Exp. or retired I.T.I Holder. 1 No.

12 Evidence of accesses to Financial Resources Evidence of access to or availability of creadit facilities (10% of estimated cost), certified by bankers (Not more than 3 months old). (Rs in Lakhs). 4.2(i) Amount To be entered (Rs in Lakhs)

13 Proposed methodology and programme of construction. Justifying their capability of execution and completion of the work as per technical specifications within the stipulated period of completion as per milestones. (Attached or not) 4.3(l)

14 Litigation History Information regarding any litigation, current or during the last five years, in which the Bidder is involved, the parties concerned, and disputed amount. (Attached or not) 4.3(j)

15 Affidavit Regarding statements made in the required attachments are true and correct. Page-24

16 Undertaking Able to invest a minimum of cost upto 25% of contract value of work. During implementation of contract. (Rs in Lakhs). 4.2(ii)

17 NOC for Debar (Affidavit)

BIHAR STATE TOURISM DEVELOPMENT CORPORATION LTD.

(A GOVERNMENT OF BIHAR UNDERTAKING)

DEVELOPMENT OF THE RAJLA SHIVA TEMPLE, LOCATED IN KUDHANI BLOCK OF MUZAFFARPUR DISTRICT, FROM A TOURISM PERSPECTIVE.

QUOTING SHEET FOR BIDDERS

Name of Contractor

Address of Contractor

E-mail ID of Contractor Mobile Number

NIT - 29/E-TENDER/ BSTDC/SBD/2026-27 GR-01

Sl No. Description Estimated Amount Rate Quoted by Contractor

% Above/Below TOTAL QUOTED AMOUNT Rs.(In Figure) TOTAL QUOTED AMOUNT Rs.(In Words)

1 Total Schedule Amount (Rs.) 49104550

2 Total Non-Schedule Amount (Rs.) To be Quoted !

TOTAL AMOUNT Rs. 57458100

DEVELOPMENT OF THE RAJLA SHIVA TEMPLE, LOCATED IN KUDHANI BLOCK OF MUZAFFARPUR DISTRICT, FROM A TOURISM PERSPECTIVE.

Based on SOR FOR BCD BIHAR - 2022 & B.S.R (ELECTRICAL) 2023

Sr. No. Item No. Item Of Work Quantity Unit Rate (Rs.) Amount (Rs.)

1 2.29.1 Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m. All kinds of soil 837.74675 100 Sqm. 1355.4 11354.8194495

2 2.8.1 Earthwork in excavation in foundation trenches or drains (not exceding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m. 1466.86525 Cum. 360.7 529098.2956750001

3 2.9.1 Excavation work in foundation trenches or drains not exceeding 1.5 m in width or 10 sq.m on plan including dressing of sides and ramming of bottoms lift upto 1,5m, including getting cut the excavated soil and disposal of surplus excavated soiis as directed, within a lead of 50 m . Ordinary rock 139.83 Cum. 568.598 79507.05834

4 2.27.2 Extra for every additional lift of 1.5 m or part thereof in : Ordinary or hard rock 0 Cum. 88.6

4 2.28 Supplying and Filling in plinth with local sand and under floors including, watering, ramming, consolidating and dressing complete. 2101.1349750000004 Cum. 287.3 603656.0783175002

5 20.2.1 Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap). 300 mm dia piles 1787.9 Metre 902.6 1613758.54

6 20.2.2 Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap). 400 mm dia piles 0 Metre 1163.3

7 20.2.3 Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap). 450 mm dia piles 0 Metre 1413.5

8 20.2.4 Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap). 500 mm dia piles 0 Metre 1639.7

6 11.72 Providing designation 100A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I 1578.6673000000003 Sqm. 283.3 447236.4460900001

7 323 (BCD) Separation Membrane of impermeable plastic sheeting 125 micron thick 275.64119999999997 Sqm. 16.56 4564.618271999999

8 4.1.5 Providing and laying in position cement concrete of specified grade exluding the cost of centering and shuttering-all work upto plinth level. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 87.84735500000001 Cum. 3434 301667.81707000005

9 4.1.4 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) 0.54 Cum. 3879.4 2094.876

10 4.1.3 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level. 1:2:4(1 Cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size) 51 Cum. 3998.1 203903.1

11 4.2.1 Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, post. struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plin window sills, fillets etc. upto floor five level excluding the cost of centring, shuttering and finishing: 1:1:2 (1 Cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size) 5.42619 Cum. 6855.6 37199.788164000005

12 4.2.3 Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, post. struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plin window sills, fillets etc. upto floor five level excluding the cost of centering, shuttering and finishing: 3.157425 Cum. 5128.3 16192.2226275

13 5.1.6 (WRD) Earth work in excavation of canals and dhars caring minimum full supply discharge above 28 cumecs (1000 cusecs) in ordinary soil (vide classification of soil item -A) and making the banks with excavated earth in proper profile and clod breaking and laying earth in 225 mm layers with an Initial lead of 30 M and lift of 1.5 M all complete as per specifications and direction of E/I 1972.5 Cum. 189.4 373591.5

14 5.1.11 (WRD) Extra for earth work in marshy, slushy and daldal soil (vide classification of soil item F) all complete as per specifications and direction of E/I 1972.5 Cum. 88.6 174763.5

15 5.1.18 (WRD) Earth work in bed clearance or desilting of canals caring full supply discharge of 28 cumecs (1000 cusecs) or more in dead courses of river etc, in ordinary soil and removing the excavated earth in proper profile in spoils etc.with an initial lead of 30 mtr and lift of 1.5M all complete as per specifications and direction of E/I. 1972.5 Cum. 146 287985

16 19.18.1 (WRD) Supplying and fixing C.I. cover without frame for manholes 455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg 0 Each 1286.9

16 5.33.2.1 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All work above Plinth level upto floor V Level. Concrete of M-25 grade with minimum cement content of 330 kg/cum 184.27190299999998 Cum. 5863.2 1080423.0216696

17 5.33.1.1 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works up to plinth level Concrete of M-25 grade with minimum cement content of 330 kg/cum 0 Cum. 5063.4

17 5.33A.1 + 5.33B.1 Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centering, shuttering finishing and reinforcement, M-20 grade reinforced cement concrete. All work upto plinth level Add or deduct for providing richer or leaner mixes respectively at all floor levels. Providing M-25 grade R.C.C. instead of M-20 grade R.C.C. 447.36 Cum. 4921.4 2201637.5039999997

18 6.1C+6.1.14C Brick work with fly ash bricks as per IS 12894 (2002) & IS 3495 in foundations and plinth in : Cement mortar 1:6 (1 cement : 6 coarse sand) 31.46 Cum. 4923 154877.58000000002

19 6.1C+6.1.14C+6.3C Brick work with fly ash bricks as per IS 12894 (2002) & IS 3495 in foundations and plinth in : Cement mortar 1:6 (1 cement : 6 coarse sand). Extra for Brick work in superstructure above plinth level upto floor V cum. 205.23624999999998 Cum. 5765.2 1183228.0284999998

20 6.1A+6.1.14A Brick work with bricks of class designation 100A in foundations and plinth in :Cement mortar 1:6 (1 cement: 6 coarse sand ) 19.29 Cum. 4819.9 92975.87099999998

21 6.1A+6.1.14A+6.3A Brick work with bricks of class designation 100A in foundations and plinth in cement mortar 1:6(1cement:6coarse sand). Extra for Brick work in superstructure above plinth level V cum. 33.800304878048784 Cum. 5662.099999999999 191380.70625000002

22 2.26 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead. 1238.05825 Cum. 123.9 153395.417175

23 6.45.2 Half brick masonry with non modular fly ash bricks of class designation 10, conforming IS : 12894, in superstructure above plinth and upto floor V level. Cement mortar 1 : 4 (1 cement : 4 coarse sand) 190.25 Sqm. 700.8 133327.19999999998

24 6.18A+6.18.4A+6.19A Half brick masonry with bricks of class designation 100A in foundations and plinth in : Cement mortar 1:4 (1 cement: 4 coarse sand) Extra for half Brick masonry in superstructure above pinth level upto floor V level. 0 Sqm. 689

24 5.33A.2.2 + 5.33B.1 Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centering, shuttering finishing and reinforcement, M-20 grade reinforced cement concrete. All works above plinth level upto floor V level Beams, plinth beams, girders, bressumers, cantilevers, Suspended floors lintels roofs and staircases including spiral staircases, shelves etc. Add or deduct for providing richer or leaner mixes respectively at all floor levels. Providing M-25 grade R.C.C. instead of M-20 grade R.C.C. 138.739925 Cum. 5841.7 810477.0198725

25 5.33A.2.1 + 5.33B.1 Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centering, shuttering finishing and reinforcement, M-20 grade reinforced cement concrete Walls columns, pillars, posts cind struts Providing M-25 grade R.C.C. instead of M-20 grade R.C.C. 26.132858000000002 Cum. 5458 142633.138964

26 5.14 Providing, hoisting and fixing up to floor five level precast reinforced cement concrete in mouldings as in cornices, windows sills etc. including setting in cement mortar 1:3 (1 cement : 3 coarse sand) cost of required centering, shuttering but excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size). 0 Cum. 9269.8

27 5.9.17 Centering and shuttering including strutting, propping etc. and removal of form for. Cornices and mouldings 0 Sqm. 625.2

28 5.9.14 Centring and shuttering including strutting,propping etc. and removal of form for. Extra for shuttering in circular work (20% of respective centring and shuttering items) 0 Sqm. 20.2

26 5.9.15 Centring and shuttering including strutting,propping etc. and removal of form for. Small lintels not exceeding 1.5 m clear span, mouldings as in cornices, window sills, string, courses, bands, copings, bed plates, anchor blocks and the like. 72.3492 Sqm. 224.2 16220.690639999999

27 13.39.2 Extra for plastering done on moulding cornices or architraves including neat finish to line and level: In two coats 27.81816 Sqm. 473 13157.989679999999

28 11.29.1 40 mm thick rough chisel dressed stone flooring over 20 mm (average) thick base including pointing with C.M 1:2 (1 cement :2 stone dust) with an admixture of pigment to match the shade of the stone with base 1:1:1 (1 lime : 1surkhi : coarse sand or 1:5 (1 cement : 5 coarse sand) Red sand stone 0 Sqm. 889.6

29 26.92.1 Providing and fixing of fa-ade at all heights with extruded hollow Clay/Terracotta ventilated rain screen tiles of height 250/300/400mm and length of 595 mm of approved texture, design and pattern having Flexural Strength/ Modulus of Rupture of > 14 N/m and maximum water absorption of 10% tested as per ISO 10545-4: 0545-4:2004(E) and ISO 10545-3:1995 respectively in true level fixed to a supporting aluminium framework(Alloy 6063 T5/T6) consisting of vertical 'T' (for intermediates)/'L'(for ends/ termination)/ Tubular sections (at corners) of size 80x60x2mm/40x60x2mm/ 40x40x2mm respectively, spaced at maximum spacing of 600mm c/c matching to the tile vertical grid, and horizontal aluminium 'C'-clamps of size 56x25x2mm thickness of length 150mm at junction of tiles and of length 75mm at wall ends/ corners fixed on top of the vertical sections at spacing of 250/300/400mm c/c matching to the tile horizontal grid with two numbers of self-drilling/self-tapping SS screws of size 5.5x25 mm with EPDM washers. The vertical 'T'/'L/ Tubular sections shall be fixed to the wall using HOG (hot-dip-galvanized) steel L-brackets (galvanizing thickness of minimum 80 microns) of size 110x80x6 mm at intermediate vertical aluminium profiles and of size 220x110x12 mm at outer corners and stainless steel grade 304, MIO full threaded anchor fasteners with nylon sleeve 100mm long (for brick work) and M8 expansion anchor fasteners 75mm long for concrete surf ace, spacing of brackets to be based on a structural/static calculation. The brackets shall be of length 175mm at junction of two vertical aluminium profiles and of length 100mm at intermediate points of vertical profiles and shall be fixed to the vertical aluminium T/L/Tubular profiles using two numbers self-drilling/ self-tapping SS screws of size 5.5x25mm with EPDM washers. EPDM gaskets to be fixed in between brackets and vertical profiles. The tiles shall be mounted on the 'C' clamps such that the tiles are supported at top and bottom at both ends. The tiles shall be additionally secured to the horizontal 'C' clamps using special SS clips of required size which shall be inserted and pressed into position on the 'C' clamps holding the tiles and the cut tiles shall be glued at points to the horizontal 'C' clamps by using MS Polymer sealant adhesive. The vertical joint open groove between two adjacent tiles shall be 5mm. The tiles and system shall be designed to resist wind load as per IS 875 (Part 3) according to different zones. The tiles shall be installed using the ventilated rainrain screen principle with provision for natural ventilation of the space between the facade tiles and the structural wall. The work shall be carried out as per specification, drawing and as per direction of the Engineer-in-Charge. Note: Scaffolding wherever required to be paid separately. With 16mm thickness (+/- 10%) terracotta tiles of grey colour 0 Sqm. 5531.6

30 11.31 Extra for pre finished nosing in treads of steps of Kota stone / sand stone slab. 0 Metre 82.9 0

31 11.32 Extra for Kota stone / sand stone in treads of steps and risers using single up to 1.05 metre.length 0 Sqm. 18.1

29 11.38 Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such shades except white, Ivory, Grey, Fume Red, Brown, laid on 20 mm thick Cement motar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. 95.88 Sqm. 862.4 82686.912

30 11.39 Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 13755 of NITCO, ORIENT, SOMANY, KAJARIA or equivalent make in colours such as white, Ivory, Grey, Fume, Red, Brown, laid on 20 mm thick cement motar 1:4 (1 cement : 4 Coarse sand) including grouting the joints with white cement and matching pigments etc, complete. 0 Sqm. 1329.8

30 11.36 Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 590.1 Sqm. 795 469129.5

31 8.12a Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20mm(avearage) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. 2179.8 Sqm. 2147.7 4681556.46

32 0089 Hire charges of sand blasting equipment 30 Day 480 14400

33 8.13.1 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. 151.9604 Sqm. 3605.2 547847.63408

34 11.4 Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS :13755 of NITCO , ORIENT , SOMANY , KAJARIA or equivalent make in colours except white , Ivory , Grey , Fume , Red , Brown , laid on 20 mm thick cement motar 1:4 (1 cement: 4 Coarse sand) including grouting the joints with white cement and matching pigments etc, complete. 0 Sqm. 1414

34 11.41A.1.1 Providing and laying Vitrified tiles in floor in different sizes {thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only.Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size Size of Tile 600 x 600 mm 378.7613 Sqm. 1022.7 387359.18151

35 11.46.3 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 800 x 800 mm. 0 Sqm. 1658

36 11.41A.1.2 Providing and laying Vitrified tiles in floor in different sizes {thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only.Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. 0 Sqm. 1116

37 11.26.1 Kota stone slab flooring over 20 mm (average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete . Base with 1:1:1 (1 lime : 1 surkhi: 1 coarse sand ) / 1:4 (1 cement: 4 coarse sand) 20 to 25 mm thick - 0 Sqm. 1252.7

35 11.47 Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 500 x 500 mm. 41.4063 Sqm. 1251 51799.2813

36 7.38.1.2 Stone tile work for wall lining upto 10.0m height with special adhesive like araldite or equivalent over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand ) including pointing in-white cement with an admixture of pigment to match the stone shade Raj Nagar plain white marble / Udaipur green marble / Zebra black marble Granite black stone 0 Sqm. 1571.7

36 13.11.4 12 mm cement plaster of mix: 1:6 (1 cement : 6 coarse sand) 1589.6018499999998 Sqm. 141.5 224928.66177499996

37 13.24.2 6 mm cement plaster to ceiling of mix: 1:4 (1 cement : 4 coarse sand) 603.9065499999999 Sqm. 125.6 75850.66268

38 13.13.4 20 mm cement plaster of mix: 1:6 (1 cement : 6 coarse sand) 1340.1823236292682 Sqm. 192.1 257449.0243691824

39 13.38.2 Extra for plastering on circular work not exceeding 6 m in radius : In two coat 204.34423679999998 Sqm. 29.1 5946.417290879999

40 13.82B.2 Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade: Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacture's specifications including appropriate priming coat, preparation of surface, etc. complete On concrete work 0 Sqm. 122.7

41 13.36.5 Extra for providing and mixing water proofing material in proportion recommended by the manufacturers: 20 mm cement plaster 1:4(1 cement: 4 sand) 0 Sqm. 10.1

40 11.3.1 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone agregate) finished with a floating coat of neat cement including cement slurry, etc. but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate 531.18 Sqm. 289.1 153564.138

41 22.8.1 Providing and laying integral cement based water proofing treatment including prepatation of surface as required for treatment of roofs, balconies , terraces etc, consisting of following operations. (a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water -proofing compound cleaning the surface before treatment, (b) Laying cement concrete using broken bricks / brick bats 25 mm to 100 mm size with 50 % of cement mortar 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 over 20 mm thick layer of cement mortar of mix 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water froofing compound conforming to IS 2545 to reuired slope and treating similary the adjoining walls upto 300 mm height including rounding of junctions, or walls ad slabs. (c) After two days of proper curing applying a secoung coat of cement slurry admixed with proprietary water proofing compound conforming to IS : 2645. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement: 4 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 and finally finishing the surface with trowel with neat cement slurry and making of 300 x 300 mm square. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test, All above operations to be done in order and as directed and specifed by the Engineer-in-Charge. With average thickness of 120 mm and minimum thickness at khurras point to be 65 .. 0 Sqm.

41 4.12 Extra for providing and mixing water proofing material in cement concrete work in the proportion recommended by the manufacturers. 400 Per 50 kg cement 57.16 22864

42 5.9.1 Centering and shuttering including strutting, proping etc. and removal of form for foundation, footings, bases of columns etc. for mass concrete 180.81 Sqm. 211.6 38259.396

43 5.9.2 Centring and shuttering including strutting,propping etc. and removal of form for. Walls (any thickness) including attached pilasters. Butteresses, plinth and string courses etc. 3340.825 Sqm. 375.1 1253143.4575

44 5.9.5 Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth bams, griders, bressumers and cantilevers. 1262.3617980000001 Sqm. 404.7 510877.8196506

45 5.9.6 Centering and shuttering including strutting, Propping etc. and removal of form for columns, pillars, piers, abutments, posts and struts. 1348.95216 Sqm. 494.4 666921.947904

46 5.9.3 Centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform. 674.20975 Sqm. 437.5 294966.765625

47 5.9.7 Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircaces. 430.5 Sqm. 439.9 189376.94999999998

48 5.2.2 Reinforced cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upto floor five level excluding cost of centering, shuttering, finishing and reinforcement. 1:1:5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size) 46.5775 Cum. 5670 264094.425

49 13.80 A.2 Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 3110.7284104292676 Sqm. 105.4 327870.7744592448

50 13.46.1 Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 1533.7265604292684 Sqm. 137 210120.53877880977

51 13.78.2 Applying one coat of cement primer of approved brand and manufacture on wall surface: Distemper primer 2204.3084 Sqm. 38.7 85306.73508

52 13.77A.1 Distempering with 1st quality washable distemper (ready made) of approved manufacturer and of required shade and colour complete. As per manufacture's specifications. Two or more coats on new work 2180.9084 Sqm. 56.6 123439.41544

53 16.22 Providing and fixing 15x15x90 cm boundary stone of hard stone with top 30 cm chisel dressed on all four sides including top (cost of excavation, refilling and concrete etc. to be paid for separately). 200 No.s 168 33600

54 10.6.1 Supplying and fixing-rolling shutters of approved make. made of required size of M.S. Iaths interlocked together through their intire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arragements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS : 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25mmM.S. Laths with 1.25mm thick top cover.r 0 Sqm. 2673.7

54 10.6.2 Supplying and fixing-rolling shuters of approved make.made of required size of M.S.Iaths inter locked together through their intire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arragements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5 cm long wire springs grade no. 2 and M.S. top cover of required thickness for rolling shutters. 80x1.20mm thick M.S. laths with 1.20 mm thick top cover. 17.28 Sqm. 2533.2 43773.695999999996

55 10.7 Providing and fixing ball bearing for rolling shutters 17.28 Sqm. 424.2 7330.176

56 10.8.1 Extra for providing mechanical device chain and crank operation for operating rolling shutters: 17.28 Sqm. 1108.7 19158.336000000003

57 13.81.1 Applying priming coat with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and softwood) 63.472500000000004 Sqm. 39.7 2519.85825

58 13.81.1A Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. One Coat 0 Sqm. 33.1

58 13.81.3 Applying priming coat with ready mixed zinc chromate yellow primer of approved brand and manufacture on steel galvanized iron/steel work 100.71 Sqm. 34.6 3484.566

59 13.93.1 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new work 164.1825 Sqm. 84.5 13873.421250000001

60 9.1.4 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). local wood 0 Cum. 54628.9

60 9.5.1.1 Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S.pressed butt hinges bright finished of required size with necessery screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. Second class teak wood 35 mm thick 0 Sqm. 3169.5

60 9.6.3 Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), including ISI marked M.S. pressed butt hinges bright finished of required size with necessery screws, all complete as per directions of Engineer-in-Charge and panelling with panels of : 12 mm thick prelaminated (with decorative lamination on one side and balancing lamination on other side) particle board Grade -1 medium density flat pressed, three layer and graded (FPT-1) conforming to IS :3087 bonded with BWP type synthetic resin adhesive as per IS :848 and prelamination conforming to IS :12823 Grade-1 Type I 57.712500000000006 Sqm. 2894.9 167071.91625

61 9.22.1 Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to I.S. 2202 (part I). On one side only 57.712500000000006 Sqm. 408.1 23552.471250000002

62 9.20.1 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including stainless steel butt hinges with necessary screws sqm 0 Sqm. 2845.6

63 9.119 Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm,made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos. of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer-in-Charge. 0 metre 379.4

62 9.1.2 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Sal Wood 0.9199999999999999 Cum. 95670.7 88017.044

63 21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). 76.52250000000001 sqm 5143 393555.2175

64 21.1 Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications,drawings and direction of Engineer-in-charge complete. 0 sqm 3698.5

64 9.118.1 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. ‘U’ cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). 23.625000000000004 Sqm. 1629 38485.12500000001

65 9.118.3 25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762mm X 25 mm or less as per requirement with an average wall thickness of 1 mm (± 0.3 mm). PVC foam end cap of size 23x10 mm are provided on both vertical edges to ensure the overall thickness of 25 mm. An M.S. tube having dimensions 19 mm x 19 mm and 1.0 mm (± 0.1 mm) is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top & Bottom edges of the shutter are covered with an end-cap of the size 25mm X 11 mm. Door shutter shall be reinforced with special polymeric reinforcements as per manufacturer’s specification and direction of Engineer-incharge to take up necessary hardware and fixtures. Stickers indicating the locations of hardware will be pasted at appropriate places. 0 Sqm. 2450.5

65 9.117.2 Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer-in-charge. Extruded section profile size 42x50 mm 74.25 metre 251.8 18696.15

66 9.117.1 Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer-in-charge 0 Sqm. 203.7

66 9.66.1 Providing and fixing ISI marked oxidised M.S. handles conforming to IS : 4992 with necessary screws etc. complete: 125 mm 66 Each 32.4 2138.4

67 9.100.1 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: 125 mm 12 Each 57.1 685.2

68 9.101.2 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete: Twin rubber stopper 39 Each 60.8 2371.2

69 21.1.1.2 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) 533.8304999999999 kg 418.4 223354.68119999996

70 21.1.2.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) 208.3725 kg 447.2 93184.182

71 9.48.2 Providing and fixing M.S. grills of requirement pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings/wooden frames with rawl plugs screws etc 3432 kg 161.1 552895.2

72 9.48.1 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 0 kg 144.5

73 9.53 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). 0 Each 130.8

72 26.23.1 Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on interlocking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile,rotary stiched double webbed white with 6 mm reveal profile (white/black),comprising of main- T runners of size 15x42 mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary intermediate cross-T of size 15x42 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall/ partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in- Charge. 106.09200000000001 Sqm. 1812.4 192281.14080000002

73 9.62.1 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete: 300x16mm 33 Each 169 5577

74 9.63.1 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete: 250x10 mm 33 Each 70.1 2313.2999999999997

75 9.63.3 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete: 150x10 mm 33 Each 48.4 1597.2

76 10.17 Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs during laying including painting the exposed portion of loop, all as per standard design complete. 41 Each 174.6 7158.599999999999

77 26A.7 b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF/Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per pecification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. 53.99999999999999 Sqm. 4474.2 241606.79999999996

78 26A.3 Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.26.2)For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement. 50.400000000000006 Sqm. 3377.5 170226.00000000003

79 9.127.1 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thick 0 Sqm. 795.6

80 1010 (BCD) Mild steel plates density = 7850 Kg/m3 0 Quintal 7451.999999999999

81 1035 (BCD) Bolts and nuts above 300 mm in length 0 Quintal 7313.999999999999

82 638 (BCD) Bright finished or black enameled mild steel screws 30 mm 0 100 Nos 62.099999999999994

79 10.36 Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 350.7219 kg 546.8 191774.73492

80 10.33.2 Providing and fixing hand rail by welding etc. to steel ladder railings & staircases railing including applying a priming coat of approved steel primer E.R.W tube 40 mm nominal dia. 0 Sqm 116.1

80 10.16.1 Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coar of approved steel primer, welded and bolted including special shaped washers etc. complete: Hot finished welded type tubes 254.11452000000003 kg 123.9 31484.789028000007

81 10.2 Structural steel work riveted or bolted in built up sections, trusess and framed work, including cutting,hoisting,fixing in position and applying a priming coat of approved ateef primer all complete. 12223.858125 kg 95.4 1166156.0651250002

82 13.116 Forming groove of uniform size from 12x12 mm and upto 25x15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-Charge. 1020.5999999999999 Metre 47.1 48070.259999999995

83 12.66X.6 Providing and fixing of Pre-coated colour or mill finish Aluminium Roofing Accessories in 0.71 mm thickness ,Alloy 31500 (IS designation) [Aluminium Alloy (AA) 3004 (ISO designation)] For color, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/tapping SS screws of size 6 x 60mm with 3mm thick EPDM seal and SS plain washer complete: Precoated/mill finish aluminium Gutter (600 mm over all girth) 0 Metre 1392.9

84 13.48.3 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications. Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture. 0 Sqm. 45.7

85 MR PUF panels are sandwiched panels made of polyurethane which is usually sandwiched between two metal sheets. A PUF panel's core is made of polyurethane while the interior and exterior are made up of thin metal sheets Thickness :- 30 mm, material - Puf, length - 8 ft, width - 3.5 ft, Maximum Withstanding temp - 100deg c, Type - Insulated panels 0 Sqm. 1856

83 12.1.3 Providing corrugated G.S. sheet roofing fixed with G.I.J. or hooks, bolts and nuts 8 mm diameter with bitumen and G. I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on over lapping of sheets complete (upto a pitch of 60°) excluding the cost or purlins, rafters and trusses. 1.00 mm thick with zinc coating not less than 275 gm/m z 14.19 Sqm 1257.3 17841.087

84 12.6.1 Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with G.I.J. or L hooks . Bolts and nuts 8 mm dia. G. 1. limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275 gm/m 2 Consider the length of the ridge 10.35 metres. The ridge will be made out of plain G. I. sheets 0.9 m x 1.8 m 4.3 Metre 599 2575.7

85 10.32.2 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.n gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 0 kg 114.6

85 5.22 Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

5.22.1B Mild Steel- 6mm dia 0 Kg 96.7

86 4.17 Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth. 280.28475 Sqm. 436.6 122372.32185

87 16.78.1 Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30 271.20000000000005 Cum. 1310.4 355380.4800000001

88 6.01 (RCD) Dry Lean Cement Concrete Sub- base Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing. a)Basic rate- 4260.18, b) add cess@1% - 42.60 c) Total (a+b)- 4302.78 d) add gst on 'c' - 516.33 e) Final Rate (c+d) - 4819.11 30 Cum. 4819.11 144573

89 6.02 (RCD) Cement Concrete Pavement Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing a)Basic rate- 7509.80 b) add cess@1% - 75.098 c) Total (a+b)- 7584.898 d) add gst on 'c' - 910.18 e) Final Rate (c+d) - 8495.08 60 Cum. 8495.08 509705

90 4.01 (RCD) Granular Sub-base with Close Graded Material (Table:- 400-1) Plant Mix Method (Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401 ) for grading- I Material a)Basic rate- 3664.22 b) add cess@1% - 36.64 c) Total (a+b)- 3700.86 d) add gst on 'c' - 444.10 e) Final Rate (c+d) - 4144.96 60 Cum. 4144.96 248698

91 8.01/408 (RCD) Cast in Situ Cement Concrete M20 Kerb Construction of cement concrete kerb with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M-10 grade foundation 150 mm thick, foundation having 50 mm projection beyond kerb stone, kerb stone laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 408 a) Basic rate- 2175.49 b) add cess@1% - 21.75 c) Total (a+b)- 2197.24 d) add gst on 'c' - 263.66 e) Final Rate (c+d) - 2460.90 50 Per Metre 2460.9 123045

92 8.08/803 (RCD) Painting Two Coats on New Concrete Surfaces Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces a) Basic rate- 79.90 b) add cess@1% - 0.799 c) Total (a+b)- 80.699 d) add gst on 'c' - 9.68 e) Final Rate (c+d) - 90.38 110 Sqm. 90.38 9942

93 7.1.37 Supply and laying 300 mm thick humous earth layer on slopes of dam with manual compaction and turfing the surface with approved dub grass with 1 k.m lead including watering and ramming till growth of grass all complete as per specifications and direction of E/I 0 Sqm. 84.91

93 16.72 Supplying and stacking of hard stone (for stone pitching) 22.5 cm thick at site. 0 Cum. 1060.8

94 16.73 Dry stone pitching 22.5 cm thick laid in courses and required profile with hammer dressed stones having no side less than 15 cm, with minimum depth of 20 cm including preparing the bedding surface etc. all complete. (Payment for Stone to be made separately). 0 Sqm. 271.4

93 11.78 Providing and laying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with jamuna sand and cutting of paver blocks as per required size and pattern,finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc.complete as per manufacturer’s specifications & direction of Engineer-in-Charge. 60mm thick C.C.paver block of M-35 grade with approved colour, design & pattern. 2.8499999999999996 Sqm. 714 2034.8999999999996

94 11.77 Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. 620 Sqm. 721.1 447082

95 16.3.9 Supplying and stacking at site. Good earth 1656 Cum. 187.7 310831.19999999995

96 11.79.1 Providing and laying factory made chamfered edge Cement Concrete paver blocks of required strength,thickness & size/shape, made by table vibratory method , to attain superior smooth finish using PU or equivalent moulds, laid in required Grey colour & pattern over 50mm thick compacted bed of coarse sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with jamuna sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks,lawns, drive ways or light traffic parking etc. all complete as per manufacturer’s specifications & direction of Engineer -in-Charge: (a) 80 mm thick c.c. paver block of M-35 grade with approved colour design and pattern 300 Sqm. 956.4 286920

97 23.7 Fine Dressing the Ground 0 100 sqm 208.8

97 23.10.1 Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more tili the grass forms a thick lawn free form weeds and fit for mowing including supplying good earth if needed. 600 100 sqm 319.6 1917.6

98 23.10.3 Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more tili the grass forms a thick lawn free form weeds and fit for mowing including supplying good earth if needed. In rows 5 cm apart in either direction 0 100 sqm 1027.4

99 23.11 Renovating lawns including weeding.cheeling the grass,forking the ground, top dressing with sludge or manure,mixing the same with forked soil,watering and maintaining the lawn for 30 days or more till the grass forms a thich lawn free from weeds and fit for mowing and disposal of rubbish as directed, including supplying good earth if needed but excluding the cost of sludge or manure. 0 100 sqm 1964.1

100 23.12 Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of al! rubbish with all leads and lifts. 0 100 sqm 3418.2

98 23.13 Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%). flooding with water, filling with earth if necessary, watering and finally fine dressing, levelling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as drected, within a lead of 50 m lift upto 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately). 600 Cum. 126.9 76140

99 11.56 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 0 Sqm. 3908.8

99 23.16 Providing and fixing M.S. fiat iron tree guard 60 cm dia. And 2 m high above ground level formed of 4 nos. 25x6 mm and 8 nos. 25x3 mm vertical M.S. flats hvetted to 3 nos. 25x6 mm M.S. flat iron rings in two halves, bolted together with 8 mm dia. And 30 mm long bolts including painting two coats with paint of approved brand and manufacture over a coat of priming, complete in all respects. 40 Each 3597.7 143908

35 15.7.2 Demolishing brick work including stacking of serviceable material and disposal of unserviceable material within 50 meters lead: In lime mortar with old mugnal bricks 0 Cum 706.3

100 15.2.2 Demolishing cement concrete including disposal of material within 50 metre lead: 1:4:8 or leaner mix Cum 599.8 0

101 15.23.2 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead For thickness of tiles above 25 mm and upto 40 mm Sqm. 47.5 0

100 15.6 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. 33.3375 Cum 219.3 7310.91375

101 15.3 Demolishing R.C.C. work including stacking of steel bars and disposal of unserviceable material withing 50 metres lead: 34.42 Cum 1411.2 48573.504

102 15.28.1 Dismantling roofing including ridges, hips valleys and gutters etc. and stacking the material within 50 metres lead of: G.S. Sheet 95.25 Sqm 67.5 6429.375

103 15.24 Demolishing dry brick pitching in floors, drains etc. including stacking serviceable material and disposal of unserviceable material within 50 metres lead. 9.525 Cum 535.6 5101.59

104 15.15.1 Extra for dismantling trusses, rafters, purlins etc. of wood work for every additional span of of one metre or part thereof beyond 10 me res: Of sectional area 40 cm2 and above 163 Metre per metre span 259.5 42298.5

105 16.70.2 Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. 449.5 Sqm. 729.4 327865.3

106 8780 (BCD) Kerb Stone Block M30 Grade of Size 375mm x 300mm 620 Each 79 48980

WATER SUPPLY SANITATION

107 B.S.R 12.78.2 Providing and fixing on wall face unplastidsed PVC (working pressure 4 kgf per sqm) rain water pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion. 110 mm diameter. 245 Metre 257.5 63087.5

108 B.S.R 17.2.1 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid 14 Each 4230 59220

109 B.S.R 17.1.1 Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low fixtures complete, including cutting and making good the walls andlevel white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and floors wherever required :White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 1 Each 4470.9 4470.9

110 17.4.1 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern 10 Each 3723.2 37232

111 17.7.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps 9 Each 2764.4 24879.600000000002

112 B.S.R 17.28.2.1 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia 28 Each 104.4 2923.2000000000003

113 17.10.1.3 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 200 mm 2 Each 5499.1 10998.2

114 17.33 Providing and fixing 600 x 120 x 5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. 9 Each 713.3 6419.7

115 18.22.1 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 100 mm diameter 2 Each 166.3 332.6

116 B.S.R 18.9.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. 20 mm nominal outer dia Pipes 116 Metre 205.3 23814.800000000003

117 B.S.R 18.8.1 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. Concealed work including cutting chases and making good the wall etc. 15 mm nominal outer dia Pipes 566 Metre 278.2 157461.19999999998

118 B.S.R 18.9.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 25 mm nominal inner dia Pipes 555 Metre 294.7 163558.5

119 B.S.R 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI :12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 23000 Per litre 9.7 223099.99999999997

120 B.S.R 18.52.1 Providing and fixing C.P. brass stop cock (concealed of standard design and of approved make conforming to IS : 893115 mm nominal bore. 20 Each 594.8 11896

121 B.S.R 19.2.2 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 150 mm diameter S.W. pipe 93 Metre 494.4 45979.2

122 19.2.4 250 mm diameter S.W. pipe 147 Metre 666.5 97975.5

123 B.S.R 19.6.2 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete: 150 mm dia R.C.C. pipe 122 Metre 410.7 50105.4

124 19.6.3 250 mm dia R.C.C. pipe 85 Metre 677.4 57579

125 B.S.R 19.27.1 Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 4 Each 3743.3 14973.2

126 B.S.R 19.2.4 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 250 mm diameter S.W. pipe Metre 666.5

126 B.S.R 19.29.1 Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame and vertical grating complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7 2 Each 7186.6 14373.2

127 B.S.R 19.30.1.1 Contructing brick masonry chamber for Underground C.I. Inspection Chamber and bend with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. Cover with frame (light duty) 455x610 mm internal dimentions, total weight of cover with frame to be not less than 38 kg. (weight of cover 23 kg. and weight of frame 15 kg.) RCC top slab with 1:1.5:3 mix (1 cement: 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 mix (1 cement:5 coarse sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm th. with cement mortar 1:3 (1cement:3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design. Inside dimensions 466x610 mm and 45cm deep for single pipe line : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 3 Each 4266.8 12800.400000000001

128 B.S.R 19.32.1 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with brick and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 3 Each 33603.4 100810.20000000001

129 B.S.R 19.34.1 Providing and fixing S.W. intercepting trap in manholes with stiff mixture of cement mortar 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 100 mm dia 15 Each 319.6 4794

130 18.49 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 60 Each 434.2 26052

131 17.69.2 Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 38 mm dia of 83 mm length and 77 mm breadth, weighing not less than 60 gms 20 Each 109.7 2194

132 17.70.2 Providing and fixing PTMT Bottle Trap for Wash basin and sink.Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms 20 Each 325.1 6502

133 17.73.1 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms 9 Each 397.3 3575.7000000000003

134 17.74 Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms. 9 Each 430.7 3876.2999999999997

135 18.18.1 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 15 mm nominal bore 12 Each 348.9 4186.799999999999

136 18.47.5 Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required: 40 mm nominal bore 10 Each 633.4 6334

137 18.65 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. 9 Each 96.8 871.1999999999999

138 18.12.5 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 40 mm dia nominal bore 97 Metre 476.8 46249.6

139 18.10.5 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 40 mm dia nominal bore 50 Metre 589.2 29460.000000000004

140 Type of materials Rate Incl. 1% Lab. Cess 12% GST

Difference in basic rates of material

Add For Seigniorage Fee @10% of Basic Materials Rate (Cost including 12% GST)

ADD 5.36 % GST ON civil Item 2384500.551140233

1.3 Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit with modular switch, modular plate, suitable size G.I. box etc as required.

1.7 Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required.

142 1.7.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 332.6 Metre 201 66852.6

144 1.7.3 2X 4 sq. mm + 1 X 4 sq. mm earth wire 246 Metre 309 76014

145 1.7.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire 195 Metre 422 82290

146 1.7.11 4 X 6 sq. mm + 1 X 6 sq. mm earth wire 156 Metre 660 102960

147 1.7.13 4 X 16 sq. mm + 1 X 6 sq. mm earth wire 118 Metre 1312 154816

148 1.7.12 4 X 10 sq. mm + 1 X 10 sq. mm earth wire 0 Metre 925 0

149 1.5 Wiring for light/ power plug plug with 2 X 4 sq. mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. 0 Metre 309 0

1.21 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.

1.22 Supplying and fixing metal/ PVC box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.

1.24 Supplying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate.etc. as required.

156 1.24.7 TV antenna socket outlet 4 Each 131 524

157 1.24.1+1.64.1 Supplying and fixing 3 pin, 5/6 amps socket outlet and 5/6 amps Modular type switch connection etc up-on switch board, as required. all complete as per instructions of Elec. Er/Architect. 37 Each 194 7178

1.27.1 Supplying and fixing following size/ modules, GI box along with modular base and cover plate for modular switches in recess etc as required.

158 1.27.1 1 or 2 Module (75mmX75mm) 22 Each 234 5148

163 1.31 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. 0 Point 414

163 1.32 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. 47 Point 531 24957

164 2.5.3 Providing and fixing following capacity busbar chamber with 4 strips of suitable size made of copper, heavy duty, complete with all accessories including connections, earthing the body etc. as required. 200A 4 Each 10550 42200

2.7 Providing and fixing following capacity four pole ON-load panel mounted changeover switches inside the existing cubical panel board including drilling holes in cubicle panel, making connections etc. as required.

167 2.19 Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. 24 Each 1513 36312

168 2.29 Supplying and fixing TPN sheet steel enclosure on surface/ recess along with 25/32 amps 415 volts, "C" curve TPN MCB complete with connections, testing and commissioning etc. as required. 24 Each 1616 38784

169 2.3 Supplying and fixing TPN sheet steel enclosure on surface/ recess along with 63 amps 415 volts, "C" curve TPN MCB complete with connections, testing and commissioning etc. as required. 24 Each 2431 58344

170 1.24.4 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin , 5/6 amps socket outlet 48 Each 112 5376

171 2.9.2 6 way ( 4 + 18 ), double door, horizontal type 0 Each 5132

171 1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box but excluding modular plate as required. 47 Each 34 1598

172 2.8.7 Supplying and fixing following way single pole & 2 + 12 way, Double door neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus-bar,earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 5 Each 2314 11570

2.32 Supplying and fixing Cable end box (Loose wire box, IP43) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240/415 V, on surface /recess complete with testing and commissioning etc. as required.

173 2.32.4 For 4 way, Double door TPN MCBDB 5 Each 1064 5320

2.12 Supplying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required'

174 2.12.1 6 amp. To 32 Amp. SP MCB 240 volt 53 Each 237 12561

MAIN PANEL & SUBMAIN PANEL

2.4 Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required.

2.12 Supplying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

181 2.2 Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel at least 2 mm thick, vitreous enameled white on both sides, and with inscription in single red colour on front side as required. 6 Each 214 1284

182 3.21 OR 3.6 +3.8 +3.9 Providing chemical/mineral maintenance free earthing system comprising of copper coated earth electrode 3 metre length and 17.2 mm outer dia along with 25 kg earth conductivity enhancing back fill mineral compound for earth inspection pit etc. as required. OR Fixing & Hole cutting in earth as per drawing of (CU) (600mm X 300mm X 3mm) plate electrode earth, all complete as per specifications and drawings attached. (1No. EARTH for UPS Main nutral only.) -The rate shall be inclusive of submission of TEST REPORT (2 Ohm) of each earth pitand -caution Note -The rate shall be inclusive of submission of TEST REPORT (2 Ohm) of each earth pitand TESTING shall be carried out in front of Officials/Consultant 4 Set 16675 66700

183 3.11 Supplying and laying 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode, including connection with G.I. nut, bolt, spring, washer excavation and refilling etc. as required. 115 Meter 721 82915

184 3.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing etc. as required. 110 Meter 53 5830

185 3.17 Providing and fixing 4 mm dia copper wire on surface or in recess for loop earthing etc. as required. 75 metre 144 10800

186 4.1 Providing and fixing lightning conductor finial, made of 25 mm dia 300 mm long, copper tube, having single prong on top, with 85 mm dia 3 mm thick copper base plate including holes etc. complete as required. 7 Each 1056 7392

187 4.8 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For vertical run) 121 Meter 145 17545

188 4.9 Fixing of copper / G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For horizontal run) 121 Meter 52 6292

189 4.4 Jointing copper/ G.I. tape ( with another copper/ G I tape, base of the finial or any other metallic object ) by riverting/ nut bolting sweating and soldering etc. As required. 58 Each 81 4698

190 4.12 Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of tinned G.I. bolts, nuts, chuk nuts and spring washers etc. complete as required. 58 Each 102 5916

(SUPPLY OF CABLE MAIN & SUBMAIN)

7.1 Laying of one number PVC insulated and pVC sheathed/XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required

191 7.1.3 Above 95 sq. mm and upto 185 sq. mm 245 Meter 336 82320

SUPPLY & INSTALLATION OF FIXTURES

192 8.16 Supply and installation of regular/standard model A.C. ceiling fan of 1400 mm sweep with service value (CM/MM) minimum 4.10, air delivery minimum 245 cum/min including wiring the down rods of standard length (up to 30cm) with 1.5 sq mm FLRS PVC insulated copper conductor etc as required. 41 Each 2838 116358

193 1.25 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate/switch box including connections but excluding modular plate etc. as required. 41 Each 358 14678

194 8.13 Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required. 4 Each 6536 26144

195 8.17.1 Supply and installation of 300 mm sweep/sizes metallic blade, heavy duty, single phase, 230 V A.C. Exhaust fan in existing opening including making good the damage, connection, testing and commissioning etc as required. 6 Each 2572 15432

196 5.6.2 Supplying and fixing 4' X 40watt suspended type LED luminaire with minimum efficacy 100 im/w ensuring uniform and continuous illumination including suspension system complete with electronic driver etc and connection with 1.5 sq. mm FRLS PVC insulated copper conductor cable etc as required. 15 Each 4587 68805

197 5.9 Supplying and fixing recess mounting 36 watt LED flat panel (2' x2') with minimum efficacy 100 Im/w in comprising of pressure die cast housing, acrylic diffuser, IP 65 protection and complete with integrated electronic driver etc directly on false ceiling including connections with 1.5 sq mm FRLS PVC insulated copper conductor cable as required. 101 Each 2663 268963

198 5.7.5 Supplying and fixing recess mounted 18 watt LED vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required. 0 Each 1509

198 1.33 Supplying and fixing 2 pin, 5/6 amp ceiling rose on the existing junction box/ wooden block including connection etc as required. 41 Each 64 2624

199 1.34 Supplying and fixing batten/ angle holder including connection etc. as required. 27 Each 80 2160

200 1.35 Erection of wall bracket/ceiling fittings of all sizes and shapes containing upto two GLS lamps per fitting, complete with all accessories including connection etc. as required. 27 Each 72 1944

201 8.21.1 Supply and erection of 4 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 130 mm, made of 3 mm thick sheet along with base plate of size 220 X 220 X 12 mm , small door opening for junction box mounting including 64 'C' series SP MCB, connector, and suitable size foundation bolts with template as required.(but without pole foundation) 0 Each 19292

202 5.14.5 Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, lP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required. 120 watt 0 Each 6654

203 5.14.5 Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, lP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required. 30 watt 0 Each 2386

204 8.1.1 Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size ) foundation including excavation and refilling etc. as required. Above 4.5 metre and upto 6.5 metre 0 Each 3771

DEVELOPMENT OF THE RAJLA SHIVA TEMPLE, LOCATED IN KUDHANI BLOCK OF MUZAFFARPUR DISTRICT, FROM A TOURISM PERSPECTIVE.

Bill of Quantity

(Each Item rate must be filled)

NON-SCHDULE ITEM

Sr. No. Item No. Item Of Work Quantity Unit Amount (Rs.) Rate (inc all taxes) (Rs.) Amount (Rs.)

1 MR Handmade Sandstone Gate Lamp, For Home, multicolour 2 Nos 45800 91600

2 MR Sandstone Konark Wheel 2 ft for Home and Office Decoration 1 Nos 83400 83400

3 NSI Planting the various varieties of plants, all complete, with digging all holes, providing sludge / manure / fertilisers etc. as required for the particular varieties, all complete, as per directions of E/I, all complete, with a maintenance of 3 months from the date of the plantation. 220 Each 500 110000

4 NSI Supplying and Installation of Garden Bench of size 150cmx70cm, Model No. DGB-004/EXL-100% rust free of Dwarka India or approved equivalent, finished with zinc plating, metallic primer, metallic top coat, metallic antique and PUP clear laquer, all complete as / directions of E/I. 12 Each 30532.5 366390

5 NSI Utilities Shifting 200000

TOTAL (CIVIL + LANDSCAPE) 851390

6 NSI Providing and fixing counter basin size- (mm) 190x550x430 (Jaquar, CAT NO-FLS-wht-5701) including fixing and all accessories as per manufacturers specification and direction of Engineer-in charge. 9 Each 11902.8 107125.2

7 NSI Providing and fixing health faucet with 1 m long flexible tube and wall hook including all fittings Jaguar model No.ALD-573 or approved equivalent. 0 Each

8 NSI Supply & Installation of wall mounted hand Dryer with Automatic hand sensor , Voltage supply 200 240 V, Power 1800 w with hot & cold air with all fitting as per direction of enginner in charge. 0 Each

7 NSI Providing and fixing soil, waste and vent pipes P.V.C. Pipe

Supply and fitting of Pvc 110 mm dia 50 Mtr 385 19250

Supply and fitting of Pvc Door Tee 110 mm dia 27 Each 400 10800

Supply & Fitting Door Bend 110 mm Dia 28 Each 279.8 7834.400000000001

Supply and fitting of Pvc 45 110 mm dia 28 Each 215.3 6028.400000000001

Supply & Fiiting Vent cowel 110 mm dia 21 Each 82.1 1724.1

Supply & fiiting Pipe Clip 110 mm Dia 20 Each 407 8140

Supply and fitting of FLOOR TRAP 110 x 110 mm dia 19 Each 432.2 8211.8

8 NSI Construction of Septic tank including carriage of materials and as per directed by Engineer in charge of approx 30000 litre. 3 Each 98708.5 296125.5

9 NSI Construction of manual Boring including carriage of materials and as per directed by Enginner in charge 3 Each 141521.69 424565.07

TOTAL (PHE WORKS) 889804.47

ELECTRICAL WORKS

10 MR Supply and Erection of 9 M Semi solar High mast with panel head frame and Foundation bolts. SITC of highly Efficient IP65 LED Hybrid Solar lighting system having minimum System lumen output as 11340 Lumen with maximum system watt age of 63 W with180 lm/W. with in built high efficiency solar panel and LIFE PO4 Battery and high efficiency micro processor based charge controller. Panel–335 W Life PO4 battery-25.6 V 60 Ah and IP65 protection. 4 no. light on each Mast of 63 watt. all complete including Foundation, installation etc 2 Each 888500 1777000

11 MR Supply, Installation, Testing and Commissioning of 15 W LED solar Stand alone Street lighting system having minimum initial lumen output of 1575 lumens (As per LM79 report of NABL lab). The luminaire must be having in built blue tooth system for monitoring health condition through an IOS & Android App based mobile application on Mobile Phone, with MPPT charge controller and IP 66 protection. The Solar lighting system should behaving 60 WpPV module, 12.8 V/40 Ah LiFe PO4 (Lithium Ferro Phosphate) battery pack, 6 mtr long M .S galvanized Tubular pole (Hot dip galvanized), Metallic battery box and Stainless steel Nuts & bolts with 4 year maintenance. Complete set make Havells (Cat no. LHSTANU7AAAI015) or approved equivalent, including all works with RCC foundation, all complete. 25 Each 60244 1506100

12 MR 11kV/415V PACKAGED SUBSTATION: HT SIDE: 4P VCB TRANSFORMER: OIL TYPE LT SIDE: 4P MCCB Outdoor type Package Substation with facility for internal lighting, earthing, padlocks etc. Connection between RMU & Transformer will be by 3 nos. 1C x 95 Sqmm. Aluminium conductor XLPE cable and connections from Transformer to LT ACB / MCCB will be by Aluminium bus bar connections. Cable termination kits for RMU shall be in the scope of supply (within the enclosure). Package Substation will have the following equipments: HT SIDE 1 No. 630A ACB as Outgoing to Transformer: 1 No. IDMT RELAY- Self Powered, Microprocessor based numerical 3 Nos. O/C +1 No. E/F (with inbuilt tripping mechanism - mytop or equivalent) with LCD display ON/OFF/Trip.. Dual core CT's for protection & metering, cast resin type and of suitable ratio & burden, (Class-1 for metering & class 5P10 for protection). Cast Resin PT's of 11000V/√3/110V/√3 ratio of Class-1 accuracy & of suitable burden with HV fuse on primary side & MCB/MPCB on secondary side. The Ring Switches and Tee-Off Circuit Breaker are provided with Integrated Earthing Switches with Making Capacity. |Live cable indicator for ring switches. |Shunt trip coil rated for 24V DC |SF6 Gas pressure indicator. Padlocking facility. Mechanical indications for breaker ON / OFF / TRIP Communicable type multifunction meter with MDI (A, V, Hz, KW, KWH, KVA, KVAH, KVAR, KVARH) Ammeter with selector switch. Voltmeter with selector switch. Line Voltage presence indicator. Transformer Auxiliary Relay with alarm & trip contacts for: Winding Temperature Oil Temperature Bucholz Emergency 'OFF' Push buttons Manual ON/OFF Push buttons 12 Windows annunciator. (Hooter @ Remote location i.e. inside LT Panel room) with necessary cabling. |Trip circuit healthy indication 230V AC/24V DC Power Pack of suitable capacity CFL based bulk head light fixture with limit switch in the HT Compartment. TRANSFORMER |11KV/415V, 400.KVA three phase, Dyn11, tapping + 15% to 15% in steps of 2.5% On load Tap changer (OLTC), CU/CU Winding Hermetically Sealed without gas cushion ONAN Transformer with standard accessories :1 No. Transformers shall be as per IS: 1180 Level 2 ( Star rated) Door interlock to trip HT breaker on opening of transformer compartment door (only in transformer's with off circuit tap changer). LT SIDE 1 No. 4pole 800A/ 50kA manually operated fixed type *MCCB with microprocessor based O/L, S/C & E/F releases. Ics Icu for the breaker. LT side metering shall include: 1set of LT cast resin CT's, PT's & Communicable type VAF meter, LED TYPE R Y B indication lamps, ON/OFF/ Trip indication lamps, control MCB's/MPCB's of required fault withstand and control wiring etc. at the LT side incomer breaker. CFL based bulk head light fixture with limit switch in the LT Compartment. Packaged Substation as described above. Each 1662500

13 MR Designing, Supply & erection of DG set of capacity given below with noise controlled devices acoustic of suitable rating, testing and commissioning of diesel generating set, radiator cooled, 3 phase, 4 wire, 50 cycles 415 +(-)1% volts AC alternator coupled directly through a set of flexible coupling on a common MS fabricated base frame with diesel engine complete with suitable size incoming cable from generator to change over/AMF panel, making 2nd incoming cable connection from transformer, outgoing cable connection from changeover/ standard panel, making second incoming cable connection from transformer, outgoing cable connection from changeover / STD panel to incomer of motor starter panel, fenced enclosure with platform for DG sets complete as per following detailed scope and specifications and directions of Engineer-in-charge. The rating should be at 1500 RPM. a) Diesel Engine b) Alternator c) Battery 24 v. d) Base Plate. e) suitable sq mm suitable core copper cable upto 40 metres. f) Tools, standard panel g) Metering set 415 VAC-1 set (Amp. meter, Volt Meter, ASS, VSS, Phase Indicator,control fuse, frequency meter, CT's) h) Metering set 60/5A/11 OV (Amp. Meter, Volt Meter) i) Overload protection for DC-1 No. j) Battery Charger 24V DC k)Copper bus bar of suitable size l) KWH meter 96 sqmm size m) Starting fuse button and key switch9on/off) n) Indicating lamps for low lubricated oil pressure, high coolant temperature, set running, load on, De control and other required accessories complete in all respects to the satisfaction of Engineer-in-charge 250 KVA DG SET Each 1995000

12 MR Feeder Pillar Design, fabrication, assembling, wiring and supply, installation, testing and commissioning of Distribution Panels fabricated out of (load bearing member of 2mm and non load bearing member 1.6 mm thick) GI sheet steel in cubicle compartmentised modular 3b construction, free standing floor mounted with bottom cable entry,300 mm MS painted stand and standing covering from 3 sides, IP 55 double door with canopy,dust and vermin proof with reinforcement of suitable size angle iron, channel, 'T sections and/or flats wherever necessary. 3 mm thick cable gland plates shall be provided at the bottom of the panels with appropriate stand etc. Panels shall be treated with all anticorrosive process before powder coating as per specifications and final approved shade. 2 Nos. earthing terminals shall be provided for all distribution panels. Panels shall be suitable for 415V, 3 phase, 4 wire, 50 HZ supply system. Lifting hooks shall also be provided in case of large panels. Approval shall be taken for each panel in the form of shop drawings before fabrication. Galvanised hardwares with zinc passivation shall be used in fabrication of panels. (Make AAA Switchgear, Indiatech panel, Neptune india) Feeder Pillar (For External Landscape lighting) IP 55 for outdoor Protection Incomer 63 Amps 4 pole MCCB Bus Bars 100 Amps TPN Aluminium bus bars with heat shrinkable insulation sleeve. - 1 Set Outgoing 63 Amps two pole MCB incomer with 63 Amps DP contactor 0-24 hours timer auto / manual and outgoings including 6 No. 10/16/20 Amps SP MCB with separate neutral link of each phase-1 set (50%) 40 Amps DP MCB with 32 amp industrial sockets - 2 sets 63 Amps 4 Pole MCB - 2 set Feeder Pillar for external / landscape lighting as described above 1 Each 166250 166250

13 NSI Supplying & installing 1.5 Ton 5 star Split Ac of sinc with complete fitting and as per direction of Engineer in charge. 6 Each 40000 240000

14 NSI Supplying & installing 2 Ton 5 star Split Ac of sinc with complete fitting and as per direction of Engineer in charge. 4 Each 65000 260000

15 NSI Water Storage Capacity : 80 litres cold water storage & 8 litres tank dispensing online normal water Water Cooling Capacity : 60 LPH *Output water temperature being 17°c No. of Faucet : 2 faucets (1 cold & 1 normal) Outer Body Material : Full SS Outer Body Dimensions (LxWxH) (mm) 680 x 720 x 1460 Net Weight 83 kgs ± 2 kgs Refrigeration – Green (eco) gas R-134 A Green Gas Operating Voltage 230 ± 10%V AC, 50Hz Power Consumption in watts (Max) 700 W Purification Capacity Up to 50 ltr/hour* Pure water recovery Up to 70% Auto Sanitization – Storage Tank ESS – Electrolytic Sanitizing System – Active Silver protects storage water tank from external contaminations and offers pure water for 24×7. 2 Each 70000 140000

TOTAL ELECTRICAL WORKS 4089350

FIRE FIGHTNING WORKS

16 MR Providing and fixing with bracket/supports etc. wall mounted fire extinguishers as per detail below :

MR ABC powder type fire extinguisher of 6 Kgs. Capacity, with initial filling (Mono Ammonium Phospate Powder) in brand new cylinder with powder coated finish, Stored Pressur type, Pressure Gauge, Controllable discharge mechanism with Hose & Nozzle , confirming to IS : 15683 : 2008. 3 Each 4500 13500

MR Carbon-di- oxide type fire extinguisher of 4.5 kgs. Capacity, Co2 gas as per IS 15222 with controll discharge mechanism fitted with Hose & Horn applicable on Class B fire rating 21B confirming to IS : 15683 : 2008. CO2 Cylinder as per IS 7285 with ISI mark. 3 Each 8950 26850

TOTAL (FIRE FIGHTING ) 40350

17 IP Varifocal Dome camera: Design, Supply, installation, testing and commissioning of 4 MP BULLET IP CAMERA., minimum 1 year warranty Make : Hikvision / Bosch / Pelco / Honeywell / GVD 30 Pcs 3990 119700

18 Supply, installation, testing & commissioning of 8 PORT POE GIGA SWITCH Make: Hikvision /Bosch /Pelco/ Honeywell / GVD 6 Pcs 6650 39900

19 Supply, installation, testing & commissioning of 4 TB Survillance HDD for camera recording. (24*7 ) Make: Hikvision / Bosch / Pelco / Honeywell / GVD 3 Pcs 9975 29925

20 Supply , Installation ,Testing and commissioning of 16 Channel NVR (Network Vedio Recorder) Make: Hikvision / Bosch / Pelco / Honeywell / GVD 3 Pcs 11970 35910

21 Supply, installation, testing & commissioning of RJ 45 CONNECTOR Make: Hikvision / Bosch / Pelco / Honeywell / GVD 30 Pcs 20 600

22 Supply, laying and termination of CAT 6 cable in existing conduits/ raceway/ cable tray for both video and control. 1200 Metre 66.5 79800

23 Supply, installation, testing & commissioning of 43" inches LED screen suitable for showing out puts from NVRs on a single screen (24x7) complete in all respect complete as required. Make: Hikvision /Bosch /Pelco / Honeywell / GVD 2 Pcs 42560 85120

TOTAL (CCTV WORKS) 390955

FURNITURE WORKS

24 KING SIZE BED Minimalistic Design Big beds don't have to mean suffocated rooms. This bed comes with clean edges and a minimalistic headboard resulting in the bed taking up the least space possible. Elegant Aesthetics Beds are the central feature of any bedroom which makes choosing the right bed of utmost importance. The Adria King bed comes with an Imperial Oak finish that is sure to make your space as elegant as you are. Melamine Impregnated Finish We believe in looking deep into the detail. The Adria King Bed is laminated with Melamine Impregnated Paper which gives a crisp finish along with making for an easy clean. King Sized Lying down on a bed after a busy day is the best feeling ever. We make sure that nothing hampers this feeling for you. Therefore, this bed comes in a spacious King size. Easy Maintenance Headboards can take up a lot of space and intricate designs make them a cleaning nightmare. That is why this bed comes with a simple headboard which is easy to clean yet stylish. Net Weight (kg)- 107.4, Sales Package- 1 Bed, Primary Material Subtype- Particle Board, Finish Color - Imperial Oak, Dimensions W x H x D (cm) - 187.5 x 90.9 x 204.5 , Style - Contemporary & Modern, Seat Height (cm) - 44, Recommended Mattress Size Depth : 198.1 cm (78"), Width : 182.9 (72"), Minimum Thickness : 10.2 cm (4") Primary Material- Engineered Wood, Warranty- 1 Year Warranty Storage Included - No, Storage Mechanism - No Storage, Delivery Condition - Knock Down, Headboard Included - Yes, Country Of Origin - India 2 EACH 47800 95600

25 KING SIZE MATTRESS Product Specifications: 1. Bed Frame: - Size: King-size (72" x 78") - Design: Modern or contemporary design 2. Mattress: - Size: King-size (72" x 78") - Thickness: 4 inches - Material: PU Foam Key Features: - Modern design for a contemporary living space - Comfortable PU foam mattress - Durable construction Technical Specifications: - Product Dimensions: 78" x 72" x 4" (Length x Width x Thickness) - Material: PU Foam (Mattress) 0 EACH 5 21800 0

26 CIRCULAR CENTRE TABLE (SMALL) Smartly designed coffee table which is more than just mere tables in the corner. The luxurious matte black touch on the metal makes it an attractive statement in your living room, bedroom or study. Round and resilient marble on the top is more like the cherry on the top which imparts that essential wholesome look to the table. Marble Size : 30 Inches Diameter Height : 18 Inches Material : Stainless Steel with PVD Finish & Black Marble Color : Black and shine Gold Best for living Room, Guest Room Handmade Item High Quality Metallic Construction 100% Rust-free Note :The top is made of marble, the texture and look might vary since its stone. Box Contains : The package that we sends consist of Table and marble with a triple layering of bubble-wrap and safely packed in a box 2 EACH 20400 40800

27 SINGLE SOFA S/F/F Sofa (Make IKEA/HERMAN MILLER/GODREJ/HAWORTH) 1Seater Sofa for lounge seating of overall size - 86cm (W) x 92cm (D) x 82cm (H) & Seat Height 45cm. 1) SEAT FOAM: The seat is made of PU foam with Density 32 ± 2 kg/cu.mtr having an additional top layer of PU foam with Density 28 ± 2 kg/cu.mtr. Seat is upholstered with fabric or leatherette. 2) BACK FOAM: The back is made of PU foam with Density 28 ± 2 kg/cu.mtr with two additonal top layer of supersoft foam of density 23 ± 2 kg/cu.mtr upholstered with fabric or leatherette. 3) UNDERSTRUCTURE: Understructure is made up of 1.2 ± 0.1 cm thick hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-184 Dia 4mm zigzag spring assembly is mounted in understructure for support and additional cushioning purpose. 4) LEG ASSEMBLY: It is a welded assembly made in stainless steel (grade SS 202) tube & plate. 5 EACH 21800 109000

28 STUDY TABLE (1500 X 600) About Material & Finish: Made of high-quality and premium material sheesham wood, this Elvira study table with drawers is sturdy in nature and offers lasting durability. The Elvira study table is available in various finish options that can enhance any space. Material - Sheesham Wood, FINISH - Honey Finish, Dimensions (Inch) - 48 L x 22 W x 30 H, Dimensions (Cm) - 121.9 L x 55.9 W x 76.2 H Brand - Wooden Street, Pack Content - 1 Study Table FEATURES - With Drawer, STORAGE - With Storage Table Top Material, Solid Wood Delivery Condition - Expert-Assembly 0 EACH

28 3 SEATER SOFA S/F/F Sofa (Make IKEA/HERMAN MILLER/GODREJ/HAWORTH) 3Seater Sofa for lounge seating of overall size - 205.5cm (W) x 92cm (D) x 82cm (H) & Seat Height 45cm. 1) SEAT FOAM: The seat is made of PU foam with Density 32 ± 2 kg/cu.mtr having an additional top layer of PU foam with Density 28 ± 2 kg/cu.mtr. Seat is upholstered with fabric or leatherette. 2) BACK FOAM: The back is made of PU foam with Density 28 ± 2 kg/cu.mtr with two additonal top layer of supersoft foam of density 23 ± 2 kg/cu.mtr upholstered with fabric or leatherette. 3) UNDERSTRUCTURE: Understructure is made up of 1.2 ± 0.1 cm thick hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-184 Dia 4mm zigzag spring assembly is mounted in understructure for support and additional cushioning purpose. 4) LEG ASSEMBLY: It is a welded assembly made in stainless steel (grade SS 202) tube & plate. 5 EACH 34000 170000

29 STUDY CHAIR S/F/F Executive Chair (Make IKEA/HERMAN MILLER/GODREJ/HAWORTH) 1) SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2 cm. thick hot-pressed plywood, upholstered withfabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. HIGH BACK SIZE : 47.5 cm (W) x 69.5 cm (H) SEAT SIZE : 47.0 cm. (W) x 48.0 cm. (D) 2) POLYURETHANE FOAM: The Polyurethane foam is moulded with density = 45 +/-2 kg/m 3 and Hardness = 20 +/- 2 at 25% compression. 3) ARMRESTS: The one-piece armrests are injection moulded from black Co-polymer Polypropylene. 4) CENTER TILT SYNCHRO MECHANISM : The mechanism is designed with the following features: · 360 revolving type. · Upright position locking. · Tilt tension adjustment. · Seat/back tilting ratio of 1:3 (60 seat tilt/180 back tilt). 5) PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0 cm. 6) TELESCOPIC BELLOW ASSEMBLY : The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. 7) PEDESTAL ASSEMBLY : The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.0cm pitch-center dia. (76.0 cm with castors.) 8) TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. 0 EACH

30 WOODEN WARDROBE Contemporary Design The sleek lines and minimalist aesthetics of this modern wardrobe bring a touch of elegance to any bedroom. Its seamless design combines functionality with stylish sophistication. Hanging Rod It is sturdy and spacious, perfect for neatly organising your clothes. Designed to support a variety of garments, this wardrobe ensures that whether it is a long dress or coat, you clothes remain tidy and accessible. External Drawer with a Lock The external drawer with lock for this wardrobe offers secure storage for valuables, ensuring peace of mind. Its design seamlessly integrates with your wardrobe, combining functionality with contemporary style. Secure Door Lock The secure door lock of the wardrobe ensures your belongings are safely stored, offering peace of mind with its robust, tamper-proof design. Engineered for durability, it provides reliable protection against unauthorized access. Sturdy Construction Crafted with engineered wood and reinforced joints, this wardrobe ensures unparalleled durability and stability, promising years of reliable use. Its sturdy construction guarantees your belongings stay secure and organised. Net Weight (kg) : 129, Sales Package : 1 Wardrobe, Dimensions W x H x D (cm) : 150 x 180 x 50, Finish Color : Brown Primary Material : Engineered Wood, Primary Material Subtype : Particle Board, Number of Lockers : No Locker Warranty : 1 Year Warranty, With Mirror : No, Number of Drawers : 1 Drawer, Number of Shelves : 8 Shelves, With Overhead Unit: No , Door Type :Hinged 2 EACH 50200 100400

31 TV CABINET WITH BOX Grand Feel with Compact Size The width of the unit is a benevolent 1350mm – with more than enough surface and storage space while, the smooth curves project the feeling of a long, large and luxurious unit which can accommodate upto 53 inch TV. Optimised Storage The volume of the unit is optimized to provide the perfect combination of open-display space to showcase products along with concealed storage space to hide products that are used infrequently. Wire Management Unit Wire management provision from TV to set top box through the panels ensures neat, concealed wiring organization of devices. Curvilinear Design The design of this unit is inspired by smooth curves, circlesand quadrantsto form a harmonious concept that stands apart and breaks the modernism trend of straight edges & sharp lines. Storage Space Sparkle TV Unit fits well into all home aesthetics Country Of Origin - India, Delivery Condition : Knock Down, Dimensions W x H x D (cm) - 180 x 180 x 40, Finish Color : Walnut, Sales Package : 1 TV Unit, Primary Material : Engineered Wood, Number of Drawers : 6 Drawers, Number of Shelves : 9 Shelves 2 EACH 35200 70400

32 SQUARE SIDE TABLE (SMALL) Bloom side table of dimension :600WX600DX428 height .Glass of 8mm thick tempered ,solid rubber wood legs and frame ,MS sheet as bottom shelf .Pu coated to the rubber wood part clear glass 0 EACH

33 SEMINAR ROUND TABLE WITH 6 CHAIR Dine in style and luxury at the glamorous Crossway Dining Set from Nilkamal. This six-seater dining arrangement of one elegant table and six trendy chairs will redefine your home dining experience. Its oval table with a clear laminated and blue vinyl laminated tempered glass top, and the four-spoke base has an aesthetic presence. Six ergonomic lounging chairs complete the set with their U-frame curve backrests for support and velvet-upholstered MDF seats for comfort. The Crossway dining set elevates modern decor with its flawless engineering, the melamine-finished rubberwood body, warm walnut colour and contemporary sense of style. Get one for your home today. Primary Material : Solidwood - Rubberwood Secondary Material : Engineered Wood - MDF Features Up your dining game with the Crossway Dining Set Modern 6-seat dining set with a table and six chairs Robust rubberwood body finished in fine melamine Table with four-spoke base and tempered glass top Plush, 180-gsm fabric is comfortable and appealing A curved U-frame backrest and MDF seat on chairs A warm walnut tone makes your space welcoming An ideal complement to your stylish dining space Other Info Color : Brown - Walnut, Style : Contemporary Seating Capacity : Six Seater 0 EACH

32 CAFETERIA DINING TABLE WITH 2 CHAIR bout Material and Finish: The Janet 2-seater dining set is made with high-quality, premium sheesham wood, ensuring both durability as well as stability. You will find these dining sets come in two different finishes: honey and walnut finish. Material - Sheesham Wood, Color : Brown , SEATER : 2 Seater, FINISH : Walnut Finish, Table Dimensions(Inch) : 28 L x 28 W x 30 H, Table Dimensions(Cm) : 71.1 L x 71.1 W x 76.2 H, Chair Dimensions(Inch) : 18 L x 18 W x 35 H Chair Dimensions(Cm) : 45.7 L x 45.7 W x 88.9 H NOTE : Its noteworthy that the chairs/bench of dining table sets would not get entirely nested beneath the table. Brand : Wooden Street, STORAGE : Without Storage FEATURES : Without Armrest , Shape : Square 6 EACH 25000 150000

33 CAFETERIA DINING TABLE WITH 6 CHAIR About Material & Finish Made of high-quality Sheesham wood, this 6 seater dining table set is sturdy in nature and offers lasting durability. You can choose from a range of variant finishes when purchasing the Wertex 6 Seater Dining Table Set. Product Features This dining table set perfectly blends style and functionality. The deep finish of the table and chairs adds a touch of elegance to any dining room. It is sturdy and well-constructed, with a smooth tabletop that is easy to clean. Chairs included in this dining set are comfortable to sit in and provide ample support for long dining hours. The dining chair cushions are made of high-quality foam and fabric, ensuring both comfort and durability. The dining table has a modern look with clean lines and a minimalist approach, whereas the chairs feature a slightly curved backrest and tapered legs, making them stand out from other dining sets in the market. Overall, the Wertex 6-seater dining set is an excellent investment for anyone as It's stylish, functional, and built to last. With this set, you'll have a comfortable and elegant dining experience for years to come. Material - Sheesham Wood, SEATER - 6 Seater, FINISH - Honey Finish, Table Dimensions(Inch) - 67 L x 36 W x 30 H, Table Dimensions(Cm)- 170.2 L x 91.4 W x 76.2 H, Chair Dimensions(Inch) - 19 L x 18 W x 40 H Chair Dimensions(Cm) - 48.3 L x 45.7 W x 101.6 H NOTE Chairs of dining table sets would not get entirely nested beneath the table. Brand- Wooden Street, STORAGE : Without Storage , FEATURES : Without Armrest, Shape : Rectangle 10 EACH 80100 801000

34 CASH COUNTER Cash Counter: Providing and fixing Cash counter of size 4500x750x750 (H)to be made of 19 mm thick BWP ply of century/ Green make for all surfaces with the working top of size 750 mm width at 750 mm level. All exposed surfaces will be finished with 1 mm mica of century/Green make. Two sets of drawer chest with two drawers and one cupboard with concealed hinges and lock and key will be provided with billing counter along with keyboard tray on telescopic channel forsmooth movement. Access flap and wire manager to be provided for electric/ Data cables. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. 1 EACH 60000 60000

35 REVOLVING CHAIR Providing and fixing MEDIUM BACK EXECUTIVE REVOLVING CHAIR with adjustable lumber support in mesh back with armrest with PU pad. The back of the chair will be provided adjustable support on head and neck for extra comfort. The seat is made up of 1.2cmm thick hot pressed plywood, upholesterse with fabric and moulded polyurethane foam. and center tilt synchro Mechanism, Peneumatic Height Adjustment. The pedestal is with twin wheel injection moulded casters.Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in- charge. 1 EACH 12500 12500

36 KITCHEN ISLAND Kitchen Island Unit with Two Burner Range: Kitchen Island Unit made of Stainless Steel Sheet and SS Square Frame with Two Burner Range of total size 12'W x 2.5'D with height 32" and 28" will be in two parts fitted with drawer for keeping spices and salt below cook top. A sliding shelf will be provided under the cook top & drawer for the store of waste cooking materials, additional shelf will be given in bottom for keeping cooked food. In another part a ss sink with swan head tap will be fitted. And also making arrangement for keeping LPG cylinder inside a covered cupboard along with three drawer unit for keeping kitchen items. The material used in fabricating the above items is such as Top Sheet 18 guage, Shelf & facia will be in 22 guage in 304 Grade, Legs & Frame -- square pipe in Grade 202, as per drawing. 1 EACH 342000 342000

37 KITCHEN HOOD Kitchen Hood: Fabricating of Kitchen Steel Hood of Size 72"x36"x20" with filter along with ducting pipe in GI sheet and exhaust fan for out-let to remove particles such as dust, dirt, smoke etc. The out-let pipe will be hanged with fast nut in the ceiling 1 EACH 140000 140000

Total Furniture = 2091700

Total NSI 8353549.47