Civil work

Amount

Dismantling, clearing away and carefully stacking materials useful for re-use for any thickness of walls

a) Floor finish and dadooing walls in cement mortar with mosaic tiles/glazed tiles/cuddapah slabs

b) Dismantling of Brick work with cement mortor

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the University Engineer and clearing and levelling the site, etc., complete as per standard specifications and as directed by the University Engineer.

Plastering with Cement Mortar 1:5 (One cement and five crushed stone sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the University Engineer.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (one cement and three crushed stone sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the University Engineer.

Plastering with Cement Mortar 1:3 (one cement and three crushed stone sand) 12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the University Engineer.

Providing Polymer Coating (Water Proof Coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust, foregin, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per ecommendation of the supplier.The mix shall be stirred thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the University Engineer etc. The rate inclusive of cost of materials and labour, etc., complete complying with standard specification and as directed by the University Engineer.

Plastering the surface of walls with Cement Mortar 1:3 (one cement and three crushed stone sand), 12mm thick in all floors including curing etc., complete complying with standard specification and as directed by the University Engineer.

Cement concrete 1:5:10 (one cement, five crushed stone sand and ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification and as directed by the University Engineer.

Plain Cement Concrete 1:3:6 (one cement, three crushed stone sand and six hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the university Engineer.

Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specifications and as directed by the University Engineer.

Supplying fabricating angles ISA of size 65x65x8mm thickness including welding works and over one coat of red oxide primer etc., complete complying with standard speciifcation and as directed by the University Engineer.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the University Engineer).

Painting old iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with one coat of best approved first quality and colour of synthetic enamel paint over the existing coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the University Engineer before use on works.)

Painting two coats of plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification and as directed by the University Engineer.

Painting the old wall with one coat of ready mixed plastic emulsion paint of first class quality and of approved colour including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (one cement and three crushed stone sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the University Engineer.

Pointing the joints of machine pressed tiles with cement mortar 1:3, the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the University Engineer.

Providing and filling the tile joint with epoxy grout with following specification: Surface preparation including cleaning the joint to be free from dust and loose particles. Providing masking tape on either side of the tile joint edges and providing sealing the tile gap with epoxy tile joint grout and finishing neatly and as directed by the University Engineer. The rate inclusive of cost of materials and labour, etc., complete complying with standard specification and as directed by the University Engineer.

Supplying and fixing in position of Solid PVC DOOR SHUTTERS using 19 gauge 19mm MS Sq. tubes for styles and outer frames. 15 mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The overall size of styles shall be 50 x 30 mm.The overall size of top rail, lock rail and bottom rail shall be 75 x 30 mm.The overall size of frames shall be 50 x 45 mm, with suitable rabate for housing the shutter. etc., complete as directed by theUniversity Engineer.

a) Door with frame

b) Door without frame

Supplying and fixing in position best quality PVC soil /waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the University Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level.

a) for 75mm dia pipe

b) for 110mm dia pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the University Engineer before use on works).

a) PVC elbow with door i) 75mm dia

ii) 110mm dia

b) PVC Elbow i) 75mm dia

ii) 110mm dia

c) PVC Tee i) 75mm dia

ii) 110mm dia

Supplying, laying and jointing UPVC pipes of approved quality and best variety conforming to BIS (sch-80) of the following dia including cutting, threading and fixing PVC specials using UPVC adhesives (but exculding cost of such specials) and fixing into wall with teak wood plugs, UPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work/ cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by University Engineer before use on works. (Internal water supply)

i) 25mm dia

Supplying and fixing in position the following UPVC Specials of heavy type and approved quality and good variety excluding fixing charges but including necessary cutting and threading of UPVC pipes, jointing the UPVC specials and jointing the specials with pipe line using UPVC solvent etc., complete complying with standard specification. (The UPVC specials should be got approved by the University Engineer before use on works.)

a) UPVC elbow 25mm dia

b) UPVC TEE 25mm dia

c) UPVC Reducer - 25 x 20

d) UPVC Reducer Elbow - 20 x 15

e) UPVC Reducer Tee - 20 x 15

Supplying and Fixing of 6mm thick good guality polycarbonate sheet panels for windows,Ventilators etc.Including cost of beeding,putty etc.,Complete complying with standard specification and as directed by the University Engineer.

Flooring with ceramic tiles of 305 x 305 x 6mm size laid over 20 mm thick cement mortar 1:3 (one cement and three crushed stone sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by University Engineer before use on works)

Supplying and fixing in position 15mm dia brass CP screw down tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the University Engineer before use on the works)

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, two crushed stone sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the University Engineer. (The water closet should be got approved by the UniversityEngineer before use on works).

Supplying and fixing position Nahani Trap/Floor Trap of the 100 x 75mm sizes with best PVC gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (one cement, three crushed stone sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI/PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the University Engineer before use on works)

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the University Engineer before use on work.

Gate valve i) 25mm dia

ii) 40mm dia

iii) 50mm dia

SREE SASTIKA BUILDERS AND CONTRACTORS (BID ID -1528727)