Spl repair to bldg No T-06 under AGE B/R_II at Tibri Mil Stn GE Gurdaspur.

Material and labour for removing existing treatment ,all loose gravel cement mortar , dirt, oil, grease and foreign material by jet of dry air, roughening and clean the surface mechanically or by grinding to make it smooth before application loose existing bituminious material manually and with heat torch gun to get smooth plain finished surface with no loose material on surface . Repair all joints & cracks and apply primer with smart care epoxy primer to seal the pores/cracksand enhance the adhesion of the coating. • Apply first coat of fibres reinforced elastomeric liquid water proofing membrane formulated with PU hybrid poymers and reinforcing acrylic fibres with sun reflective index (SRI) of 100-110, having minimum elongation of 300% to 350%, tensile strength of 1.8 Mpa to 2.9 Mpa and shall have cracks bridging ability upto 10-12 degree celcius with 33% dilutioon of priming coat. Laying of fiber mesh of 0.3mm thickkness weave in leno pattern having 45 gsm/sqm and pasting it properly with overlap of 50 mm and allow it to dry for 10 to 12 Hrs. Apply second of undiluted coat @0.45ltr/sqm and allow it to dry for 4 to 5 Hrs. Apply third and final coat undiluted @0.45 ltr/sqm all as specified and as per manufacturers specification having warranty for 10 years . (Note : Application of water proofing treatment will be done by Authorised Applicator only) .

M&L for flush pointing on bricks laid flat in CM 1:3 with raking out new and existing joints, complete all as specified and directed.

M&L for PCC 1:2:4, type B1 (using 20mm graded crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed by Engineer-in-Charge.

M&L for ceramic glazed dark shade coloured tiles of size 450x300x7mm thick joint free on and including 10mm thick screed bed in CM(1:4) set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles on vertical surfaces of wall as in skirting/ dado and demolition of existing tile complete all as specified.

M&L for non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.11 sqm to 0.18sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in CM 1:4 and demolition of existing tile complete all as specified.

M&L for dark/light coloured vitrified tiles 9 to 10mm thick joint free (square/rectangular) area of each tile n exc 0.36 sqm as in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in CM 1:4 and demolition of existing tile complete all as specified.

M&L for green marble work 14-16 mm thick (table rubbed and polished) in steps, jambs, pillars window cills, cooking platforms, stair case and like in cement mortar ( 1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including 15 mm thick screed bed in CM 1:4 and demolition of existing marble complete all as specified and directed (The marble shall be fixd in one piece only).

M&L for 75mm thick PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection finishing the surface even and fair complete all as specified and directed by Engineer-in-Charge.

Demolition of PCC of any description and in any position (in sunken, floor, plinth etc) not otherwise specifically provided for complete all as specified & directed.

M&L for repairing of RCC projections, chajjas, roofs, facia etc. by necessary preparations i.e. scrapping, cutting, chiseling, dusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC surfaces and applying one coat of cement slurry and filling the surfaces with cement concrete (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) and finished with cement sand mortar (1:3) using coarse sand in patches area n. exc 5 Sqm each and thickness of RCC member exc 50mm including applying two coats of finishes existing at any height complete all as specified.