REPAIRS/RENEWAL OF OH LINE, LT UG CABLE, LT POLE, RE-STRINGING OF OH LINE, CUTTING OF TREE BRANCHES AND ALLIED WORKS AT ZONE II A AND D AND CERTAIN OTHER AREA UNDER GE (UTILITY) SECUNDERABAD

Amount

M&L for attending, repair and rectification of external LT/HT electric supply complaints on 1100/11000 Volts grade, over head/underground system alongwith necessary T&P, safety devices as per site requirement for the following type of complaints complete all as specified and directed:-

Replacement of worn out jumpers, jointing and tightening with new ACSR conductor. Note:- Single phase/two wire or 3 phase/4 wire system will be considered as one job for payment purpose.

Disconnecting from over head conductor, cutting worn out portion of LT cables of any type and size, carry out repairs including taking out cables from under ground loop line and rejoining the same to restore electric supply. Note :- (i) LT Jointing Kits, Cable protection Pipe if required at site will be measured and paid separately. (ii) Quoted rate is deemed to be inclusive of cutting and removing the pole coping and inserting the cable alongwith protection pipes.

Taking down old unsv Street light fittings in any position of any capacity, Repair of street light fittings by replacement of unsv spares and re-fixing the same in existing location. Note:- Spares for repair of street light fittings will be measured and paid under respective items.

Notes for Item Nos 1.01 to 1.03 :- (a) The contractor will be allotted complaints at MES complaint cell on daily basis on all working days and sufficient resources will be deployed by him/her for completion of day to day complaint within 24 Hrs from the time of reporting. Any delay beyond above mentioned time limit without intimation of sufficient cause, penalties will be recovered twice of the quoted rate for each un-attended complaint. (b) A detailed log of complaints with completion/non-completion remarks from users/MES will be maintained by the contractor and the same will be updated on daily basis in consultation with Engr-in-Charge or JE E&M as detailed. (c) The contractor will make suitable arrangement for emergency complaints and will notify auth rep/Engr-in-Charge about extraordinary circumstances for probable non-completion or delay in rectification of complaints beyond stated time limit set for disposal of complaint. In case of any dispute the decision of accepting officer will be final and binding in this regard. (d) The contractor will intimate MES authority well in advance if electric shutdown is required during rectification of complaints. (e) The quoted rate is deemed to be inclusive of transportation and other expenses required for the resource deployment at the complaint site around scattered Military station at Secunderabad. (f) The contractor will maintain location wise record of each spare utilized as per inventory format given by AGE E/M, Secunderabd and the same shall be submitted to E/M No II store on daily basis.

M&L for ACSR conductor, steel reinforced for LT over head lines on poles including streching tightining of poles insulator with binding wire of suitable size with insulator/streching of ACSR conductor including disconnecting/taking out old existing unsv ACSR conductors complete all as specified and directed.

M&L for Pin type, porcelain, vitreous, white, brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, 100 mm height, 65 mm dia for 1100 volts grade, including disconnecting/taking out old existing unsv insulators complete all as specified and directed.

M&L for Shackle type, Porcelain, vitreous, white, brown or green insulator including galvanised mild steel straps, washers, insulator bolts, washers and nuts of size 100 mm height, 115 mm dia for 1100 Volt grade, section of straps 31x5 mm, including disconnecting/taking out old existing unsv insulators complete all as specified and directed.

S&F Stay assembly comprising of 7/10 SWG galvanised MS stranded stay wire of required length, minimum tensile strength 70 Kg/mm (grade-2 quality) fixed to pole with and including FI clamps( Made out of 50 X6 mm MS Flat), bolts ( Minimum 16 mm dia of required length), nuts, washers, galvanised steel stay rod 16mm dia 180 cm long bow 400 x 14 mm nuts/bolts, washers, loop type insulator of size 65 x 90 mm vitreous, clearance dia of hole 16mm, stay plate of size 230 x 230 x 6 mm including necessary excavation and earth work PCC 1:3:6 type C-2 using 40 mm graded crushed stone aggregate in foundation and disposal of surplus soil, upto 50m including disconnecting/taking out old existing unsv stay assembly complete all as specified and directed. Note : Quoted rate inclusive of all as required for proper functioning of stay assambly like Excavation, PCC, stay rod, clamo nut bolts Stay wire etc

S&F of Galvanised steel wire (GI) 4mm dia including disconnecting/taking out old existing unsv GI wire complete all as specified and directed.

M/L for cross arms, bracing, supports clamps and back plates fabricated from structural steel section incl nuts, bolts washers, welding, bending cold or hot drilling holes for bolts in any shapes or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint including disconnecting/taking out old existing unsv cross arms complete all as specified and directed.

Supply & Replace MCCB along with both side spreader link and nut bolts of appropriate size (Conforms to IEC:60947-II/IS:13947-II) in exisitng LT Panel box/Feeder Pillar boxes (KIOSK),in MCCB DBs Adjustable thermal magnetic setting of capacity 400 Amps, 4 Pole, 35 KA, 415 Volt including disconnecting/taking out existing old unsv/burned MCCB complete all as specified and directed. Make : Standard or techno commercial equivalent model in Havells/Standerd/L&T.

All as per item No-8 here in before but of capacity 250 Amps, 4 pole, 25 KA

All as per item No-8 here in before but of capacity 200 Amps, 4 pole, 25 KA

All as per item No-8 here in before but of capacity 160 Amps, 4 pole, 16KA

All as per item No-8 here in before but of capacity 125 Amps, 4 pole, 16 KA

All as per item No-8 here in before but of capacity 100 Amps, 4 pole, 16 KA

All as per item No-8 here in before but of capacity 63 Amps, 4 pole, 16 KA

S&F MCB, 63 Amps, 4 pole, 415 Volts with breaking capacity 10KA, including disconnecting/taking out existing old unsv/burned MCB complete all as specified and directed.

All as per item No-15 here in befor but of capacity 40 Amps, 4 pole, 415 Volts with breaking capacity 10KA

All as per item No-15 here in befor but of capacity 32 Amps, 4 pole, 415 Volts with breaking capacity 10KA

S&F MCB, SP 10-32 Amps, 415 Volts with breaking capacity 6KA, including disconnecting/taking out existing old unsv/burned Isolator complete all as specified and directed.

Supply and fixing surface mounting analog timer switch 240 Volts, 50 Hz, 16-20 Amps rating (For Street light/High Mast light) fitted inside steel enclosure complete all as specified and directed Make : Legrand cat No 6499 15 or equivalent of ABB/Schneider/ siemens .

S&F contactor 3 phase 415 volts 50 Hz of ML-2, 32 Amp rating, coil voltage 420 volts, fitted inside steel enclosure complete all as specified and directed. Make : L&T cat No SS90701 or equivalent of Legrand/Indoasian.

Taking down and Relaying of LT cable of size10sq mm to 35 Sqmm 2/3.5 core after carrying out necessary Repair such as joining with Epoxy joint and laid with sand Cushioning and brick protection and making connection By using Lugs all as specified and directed by ingr in charge. Note: ( Earth work , sand Cushioning, brick protection, Lt Joints shall be measured and paid separately under Relevent Item) (b) Retrived serviceable bricks/ PCC cover shall be reused under relevent item) Notes : Excavation, Retuning, Sand and extra brick shall be measured and paid separately.

Taking down and Relaying of LT cable of size50sq mm to 240 Sqmm 2/3.5 core after carrying out necessary Repair such as joining with Epoxy joint and laid with sand Cushioning and brick protection and making connection By using Lugs all as specified and directed by ingr in charge. Note: ( Earth work , sand Cushioning, brick protection, Lt Joints shall be measured and paid separately under Relevent Item) (b) Retrived serviceable bricks/ PCC cover shall be reused under relevent item) Notes : Excavation, Retuning, Sand and extra brick shall be measured and paid separately.

Supplying, erecting and fixing steel tubular swaged poles with cast iron base plate of size 300mm x 300mm x 6mm, finial taper plug, bolts, nuts & screws for type 410 SP-31 (9.0 mtrs long) including painting with two coats of aluminium paint over one coat of red oxide primer on all exposed surfaces and tarring with black bituminous paints to embedded portion in PCC and providing 3 Nos of 30cm wide circular bands with black & yellow paint starting from plinth level at a gap of 30 cm in between 2 bands and numbering of poles, in yellow paint over black painted back ground at a height of 2m from bottom of pole with 5 cm large bold letters 2" (inch) wide including taking down old unserviceable PCC poles of any type complete all as specified and directed. Note: Excavation, earth work, PCC in foundation and coping shall be measured and paid separately under relevant item of this schedule.

Restreching/Restringing, tightening and repair to overhead line ACSR conductor (Only for street light 2 wruns) of any size on LT poles including necessary Aluminium binding wire connectors PVC sleeves for jumper, fixing of insulators and prunning of tree complete all as specified and directed. Notes: (i) The distance between pole to pole in one span (contains 2 runs) i.e one span will only be considered for payment purpose. (ii) No Extra conductor will be measured for binding to insulators / jumpering etc.

Restreching/Restringing, tightening and repair to overhead line ACSR conductor ( 4 /5/ 6 Runs ) of any size on LT poles including necessary Aluminium binding wire connectors PVC sleeves for jumper, fixing of insulators and prunning of tree complete all as specified and directed. Notes: (i) The distance between pole to pole in one span (contains 4/5/6 runs of ACSR Conductor ) i.e one span will only be considered for payment purpose. (ii) No Extra conductor will be measured for binding to insulators / jumpering etc.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth, for foundation of PCC/Steel pole, laying of cable in trenches etc and getting out in Hard / Dense soil complete all as specified and directed.

All as per item No 28 above but depth exc 1.5 mtr but not exc 3 mtr.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm in soils complete all as specified and directed.

Removing excavated material (soils) n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

M&L filling sand in trenches for sand cushioning of laying of cables to the full width of excavated trench 8 cm thick before laying the cable and 15 cm above the cable, gently punned down, stretching and testing of cable on transformer yard etc complete all as specified and directed. Note :- Thickness of sand cushion after punning down (i.e 18 cm) shall be measured for payment.

Supply and Laying bricks, common burnt clay building bricks, sub class 'B' of size 230 x 115 x 75 mm laid across in trenches for cable protection complete all as specified and directed.

Laying only old Brick in trenches for Under Ground Cable Protection (Serviceable Materials obtained from Item No. 1 here-in-before), complete all as directed.

M&L PCC 1:4:8 type D2 using 40 mm graded stone aggregate for filling & foundation of pole & mass complete all as directed

M&L PCC 1:3:6 type C2 using 40 mm graded stone aggregate for filling & foundation of pole & stay complete all as directed

M&L PCC 1:2:4 type B1 using 20 mm graded stone aggregate for coping of pole complete all as directed

Cutting the existing road/PCC surface straight by manual, depth and width not less than 1 mtr below ground level for passing of underground cable and filling back with excavated soil upto 75% road portion and 25% shall be made with cement concrete 1:2:4 (using 20 mm graded aggregate stone complete all as specified and directed.

M&L for road crossing/drain crossing by adopting trench less tunneling work through specified pipe jacking method by erecting the equipment to true to the allignment and gradient by haidrolic pipe jacking technique complete including tunneling, excavation in any type of soils including hard rock, HDPE pipe medium duty duty of size 100 mm dia in any length including jointing materials to carry LT UG cables of size upto 240 Sqmm and necessary conveyance charges of machinery and other required materials in co-ordination with the concerned authorites complete all as specified and as directed.

M&L for replacement of broken earth pit made out of PCC 1:2:4 type B1 using 20 mm graded crushed stone aggregate, 20 mm thick and earth pit cover made out of RCC 1:2:4 type B1, cover reinforced with 8 mm dia MS deformed bars @ 100 mm centre to centre both ways with hook made out of 8 mm dia bar, watering arrangement with funnel and wire mesh and including reconnecting of earth lead of any type with new nuts, bolts and washers etc as required at site complete all as specified and directed.

M&L repair/maintenance of stay by tightening of stay wire after untying the conductor spans from the poles to make correct tensions and maintain verticality of poles, including re-jointing the conductors in position with new binding wire complete all as specified and directed.

M&L for painting the existing LT steel poles of 9.0 Mtr long including cross arms, clamps, street light junction boxes etc with 1 coats of aluminium paint including throughly cleaning the existing surface, writing of pole numbers in yellow circle 15 cm with black paint on poles. Painting the poles up to 1.5 Mtr height with alternate bands 30 cm height (3 Nos black and 2 Nos Yellow) from ground level, complete all as specified and directed.

M&L for painting the existing LT PCC poles with 1 coats of synthetic enamole base paint including painting of cross arms, clamps, etc with one coat of aluminium paint and providing alternative band of 30 cm width (3 black and 2 yellow) from bottom of pole to 1.5 metres height , writing of pole numbers in yellow circle15 cm with black paint on poles complete all as specified and directed.

Advance Maintenance Free G.I. SAFE EARTHING Electrode with PIPE of not less than 50 mm outer dia) and two meter length, The electrode should be of galvinised (80 -100 micron) along with earth lead as Galvanised steel strip of size 32 X6 mm 7.5 m . The GI Electrode shall be pre-filled with Cristaline Conductive Material (CCM) . The GI electrode shall be surrounded with 25 kg BackFill compound to provide maximum contact between the electrode and Back Fill Compound. The earting pit cover should be factorty built ( size TOP- 10 Inch, Bottom -13 Inch, Height 10.25 Inch ) made of heavy duty Polypropylene complete all as specified and directed make ASHLOK / INDELEC/JMV / TERCEL/TRUE POWER

Trimming/pruning and removing of tree branches or any other foreign objects from LT over head conductor ( only street lights) and clearing the OH Line of any type and size for one span of any length in 2 way conductor system. Notes: (i) The contractor is responsible for provision of Necessary T & P and safety equipments required to complete the job.(ii) Necessary shutdown to be taken from concern JE Before starting the work (iii) Average length of span is 30 mtr

Trimming/pruning and removing of tree branches or any other foreign objects from LT /HT over head conductor and clearing the OH Line of any type and size for one span of any length in 3 way /4 way/5 way / 6 way conductor system. Notes: (i) The contractor is responsible for provision of Necessary T & P and safety equipments required to complete the job.(ii) Necessary shutdown to be taken from concern JE Before starting the work (iii) Average length of span is 30 mtr.

Cutting unaxious green growth and grass by manual labour or by machine at all 11 KV Electric Installation premisses/around 2/4 Pole structure/along the boundary fencing and removing rubbish from the site of work complete all as specified and directed.

Supply and replace LED Driver suitable for upto 45 watts LED light fittings complete all as specified and directed. Make : Bajaj cat part No BGD 70 065 5Y or techno commercial equivalent model in Philips/Wipro/Havells/ Surya.

Supply and replace LED Driver suitable for upto 60 watts LED light fittings complete all as specified and directed. Make : Bajaj cat part No BGD 36 185 5Y or techno commercial equivalent model in Philips/Wipro/Havells.

Supply and replace LED Driver suitable for upto 72 watts LED light fittings complete all as specified and directed. Make : Bajaj cat part No BGD 36 180 5Y or techno commercial equivalent model in Philips/Wipro/Havells.

Supply and replace LED Driver suitable for upto 90 watts LED light fittings complete all as specified and directed. Make : Bajaj cat part No BGD 66 140 5Yor techno commercial equivalent model in Philips/Wipro/Havells.

Supply and replace LED Driver suitable for upto 100 watts LED Flood light fittings complete all as specified and directed. Make : Bajaj / Philips/Wipro/Havells/Surya.

Supply and replace LED Driver suitable for upto 150 watts LED Flood light fittings complete all as specified and directed. Make : Bajaj / Philips/Wipro/Havells/Surya.

Supply and replace LED Driver suitable for upto 200 watts LED Flood light fittings complete all as specified and directed. Make : Bajaj / Philips/Wipro/Havells/Surya.

Supply and replace LED Driver suitable for upto 120 watts LED Flood light fittings complete all as specified and directed. Make : Bajaj / Philips/Wipro/Havells/Surya.

Supply and fixing steel light bracket made out of 40 mm bore mild steel GI light grade tubing over all length 1.5 mtr bend to shape as directed including providing two Nos MS flat iron 40x6 mm clamp of appropriate size with nut bolts and washer duly painted with two coat of synthetic enamel paint over a coat of primer (GI surface shall not be painted) complete all as specified.

S&F PVC insulated unsheathed/sheathed cable with stranded Aluminium conductor 1100 Volts grade, flat twin core service cable of size 4 Sqmm conforming to IS:694/1990 with latest amendments ISI including disconnecting/taking out existing unsv/damaged old service cable complete all as specified and directed. Make : Richa/havells/fincab or equivalent.

All as per item No-57 above but of size 6 Sqmm complete all as specified and directed.

All as per item No-57 above but of size 2.5 Sqmm complete all as specified and directed.

All as per item No-57 above but of size 10 Sqmm complete all as specified and directed.

Supply and laying GI tubing light grade of size 40 mm for cable protection on road/drain/floor/pole including necessary clamps 40x4mm. Make : TATA/Jindal/Bansal with ISI marked.

Supply and laying GI tubing light grade of size 50 mm for cable protection on road/drain/floor/pole including necessary clamps 40x4mm. Make : TATA/Jindal/Bansal with ISI marked.

S&F LT line rigid PVC Spacers spiral type, two lines, Phase to phase distance 300 mm, spacer rod dia 13 mm, spiral hole dia 5-6 mm and spiral length 250 mm.

S&F LT line rigid PVC Spacers spiral type, three lines, Phase to phase distance 600 mm, spacer rod dia 13 mm, spiral hole dia 5-6 mm and spiral length 250 mm.

S&F LT line rigid PVC Spacers spiral type, four lines, Phase to phase distance 900 mm, spacer rod dia 13 mm, spiral hole dia 5-6 mm and spiral length 250 mm.

S&F On-Load changeover switch (In sheet steel enclosure), AC 21 (Side Handle), 4 pole of capacity 400 Amps, 415 Volts, 50 Hz, Conforms to HSN Code : 8536 complete all as specified and directed. Make : Standard or techno commercial equivalent dolel in Havells/Benlo/L&T

S&F On-Load changeover switch (In sheet steel enclosure), AC 21 (Side Handle), 4 pole of capacity 200 Amps, 415 Volts, 50 Hz, Conforms to HSN Code : 8536 complete all as specified and directed. Make : Standard or techno commercial equivalent dolel in Havells/Benlo/L&T

S&F On-Load changeover switch (In sheet steel enclosure), AC 23 (Side Handle), 4 pole of capacity 100 Amps, 415 Volts, 50 Hz, Conforms to HSN Code : 8536 complete all as specified and directed. Make : Standard or techno commercial equivalent dolel in Havells/Benlo/L&T

S&F On-Load changeover switch (In sheet steel enclosure), AC 23 (Side Handle), 4 pole of capacity 63 Amps, 415 Volts, 50 Hz, Conforms to HSN Code : 8536 complete all as specified and directed. Make : Standard or techno commercial equivalent dolel in Havells/Benlo/L&T

S&FMCCB box made of sheet of 2mm thick size 30X20X15 CM Powder coated Suitable for fixing at Pole including two set of clamps comprisinf with the following i) MCCB 63 Amps 16 KA TP WITH BOTH SIDE SPREADER LINK.

Dismantling of damage /broken PCC LT Pole including coping of any size, removing debries from site and making good of disturbed surface to match with adjoining surface complete all as specified and directed

Dismantling LT steel tubuler pole of any height by taking out from PCC foundation complete and shifting to other location as directed including fixing the pole in true vertical position including excavation and earth work, PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as base concrete and PCC 1:3:6 type C2 (using 20mm graded stone aggregate) in both foundation and coping of poles all as specified in SSR Part I-2009 and applying two coats of aluminium paint to pole surface complete all as directed by Engineer-in-Charge.

Taking down and refixing of ACSR conductor, steel reinforced for LT over head lines on poles including streching tightining of poles insulator with binding wire of suitable size with insulator/streching of ACSR conductor complete all as specified and directed.

Taking down and refixing of insulator Pin type, porcelain, vitreous, white, brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, complete all as specified and directed.

Taking down and refixing of insulator Shackle type, porcelain, vitreous, white, brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, complete all as specified and directed.

Taking down and refixing cross arms, bracing, supports clamps and back plates fabricated from structural steel section incl nuts, bolts washers, welding, bending cold or hot drilling holes for bolts in any shapes or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint complete all as specified and directed.

Servicing of ACB 4 pole 415 Volt up to 1000 amps including tripping test complete all as specified and directed

Provision of mechanical interlocking between two ACB 4 pole 415 volt 630/800 amps including all necessary arrangements including testing complete all as specified and directed

Removing of cable connection from ACB /MCCB after taking proper shutdown after consulting Engr-in-Charge before commencement of connection work for replacement of unserviceable aluminium lugs of size 300 MM and reconnect the same , testing complete all as specified and directed

Removing of cable connection from ACB /MCCB after taking proper shutdown after consulting Engr-in-Charge before commencement of connection work for replacement of unserviceable aluminium lugs of size 240 MM and reconnect the same , testing complete all as specified and directed

Removing of cable connection from ACB /MCCB after taking proper shutdown after consulting Engr-in-Charge before commencement of connection work for replacement of unserviceable aluminium lugs of size 185 MM and reconnect the same , testing complete all as specified and directed

Removing of cable connection from ACB /MCCB after taking proper shutdown after consulting Engr-in-Charge before commencement of connection work for replacement of unserviceable aluminium lugs of size 150 MM and reconnect the same , testing complete all as specified and directed

Removing of cable connection from ACB /MCCB after taking proper shutdown after consulting Engr-in-Charge before commencement of connection work for replacement of unserviceable aluminium lugs of size 120 MM and reconnect the same , testing complete all as specified and directed

Removing of cable connection from ACB /MCCB after taking proper shutdown after consulting Engr-in-Charge before commencement of connection work for replacement of unserviceable aluminium lugs of size 95 MM and reconnect the same , testing complete all as specified and directed

Removing of cable connection from ACB /MCCB after taking proper shutdown after consulting Engr-in-Charge before commencement of connection work for replacement of unserviceable aluminium lugs of size 50 MM and reconnect the same , testing complete all as specified and directed

S&F MCCB box made of CRCA sheet of 2mm thick size 40X30X20 CM Powder coated Suitable for fixing at Pole including two set of clamps / wall byusing anchor bolt comprising MCCB 63 Amps 16 KA FP WITH BOTH SIDE SPREADER LINK complete all as specified and directed.

S&F MCCB box made of sheet of 2mm thick size 40X30X20 CM Powder coated Suitable for fixing at Pole including two set of clamps / wall byusing anchor bolt comprising MCCB 100 Amps 16 KA FP WITH BOTH SIDE SPREADER LINK complete all as specified and directed.

S&F MCCB box made of sheet of 2mm thick size 40X30X20 CM Powder coated Suitable for fixing at Pole including two set of clamps / wall byusing anchor bolt comprising MCCB 200 Amps 16 KA FP WITH BOTH SIDE SPREADER LINK complete all as specified and directed.

Supply and fix on wall with necessary arrangements busbar chamber 100 amps 4 way 4 pole wall mounted IP -31 , made out of 1.6 mm thick CRCA sheet epoxy powdwer coated single layer operational voltage 440 Volt , Short circuit current capacity 25 KA for 1 Second including necessary cable connections complete all as specified and directed. Note: Quoted rates inclusive of necessary fixing arrangement and cable connections , cable glands as required for proper fixing / functioning of Bus Bar Chamber. Make : Havells/ HPL/Standerd,

Supply and fix on wall with necessary arrangements busbar chamber 200 amps 4 way 4 pole wall mounted IP -31 , made out of 1.6 mm thick CRCA sheet epoxy powdwer coated single layer operational voltage 440 Volt , Short circuit current capacity 25 KA for 1 Second including necessary cable connections complete all as specified and directed. Note: Quoted rates inclusive of necessary fixing arrangement and cable connections , cable glands as required for proper fixing / functioning of Bus Bar Chamber. Make : Havells/ HPL/Standerd,

Supply, Installation, test and Commissioning CPRI APPROVED factory fabricated, out door type, LT FEEDER PILLAR BOX made out of 3.15 mm thick CRCA Sheet with projected Globe roof for rain water protection Dust and Vermin Proof , Double door with both side opening including Neoprene Rubber Gasket,, suitable for 440 Volt 3 Phase 4 Wire System ,including Danger Plate, Earthing Strip Point and Ventilation Louvers at Rear Side, Bottom detachable Gland Plate comp-lete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers, etc. and embeded with 50X50X6mm Mild Steel Angle Iron Frame and 600 mm above the Normal Ground Level comp -lete with internal connection with suitable size of cable ,cable lugs,and cable glands PCC Foundation in Cement Concrete 1:3:6 (20mm Graded Stone Aggregate) and Test-ing after Installation complete all as specified and comprising of the following :–(Size not less than 1.05mx1.6 M x0.4m)

Supply, Installation, test and Commissioning CPRI APPROVED factory fabricated, out door type, LT FEEDER PILLAR BOX made out of 3.15 mm thick CRCA Sheet with projected Globe roof for rain water protection Dust and Vermin Proof , Double door with both side opening including Neoprene Rubber Gasket,, suitable for 440 Volt 3 Phase 4 Wire System ,including Danger Plate, Earthing Strip Point and Ventilation Louvers at Rear Side, Bottom detachable Gland Plate comp-lete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers, etc. and embeded with 50X50X6mm Mild Steel Angle Iron Frame and 600 mm above the Normal Ground Level comp -lete with internal connection with suitable size of cable ,cable lugs,and cable glands PCC Foundation in Cement Concrete 1:3:6 (20mm Graded Stone Aggregate) and Test-ing after Installation complete all as specified and comprising of the following :–(Size not less than 1.05mx1.5 M x0.4m)

Supply & fixing of 4 pole power contactor 02NO +02NC,63Amps MCX-12,50Hz suitable for existing one and including taking down old unserviceable one complete all as direrected by Engr-in-Charge. Make L&T/Schnieder/Siemens

Supply & fixing of 4 pole power contactor 02NO+02NC, 130Amps,MCX-23,50Hz suitable for existing one and including taking down old unserviceable one complete all as direrected by Engr-in-Charge. Make: L&T/Schneider/Siemens

Supply & fixing of 4 pole power contactor 02NO+02NC,200Amps,MCX-33,,50Hz suitable for existing one and including taking down old unserviceable one complete all as direrected by Engr-in-Charge. Make: L&T/Schneider/Siemens

Supply & fixing of 4 pole power contactor 02NO+02NC,360Amps,MCX-42,50Hz suitable for existing one and including taking down old unserviceable one complete all as direrected by Engr-in-Charge. Make: L&T/Schneider/Siemens

Supply & fixing of 4 pole power contactor 02NO+02NC,400Amps,MCX-43,50Hz suitable for existing one and including taking down old unserviceable one complete all as direrected by Engr-in-Charge. Make: L&T/Schneider/Siemens

Supply & fixing of 4 pole power contactor,02NO+02NC,100Amps, MCX-22,50Hz suitable for existing one and including taking down old unserviceable one complete all as direrected by Engr-in-Charge. Make: L&T/Schneider/Siemens

Supply & fixing of 3 pole power contactor AC/DC Control ,Ie -1000Amps current rating,415 volts,50Hz suitable for existing one and including necessary fixing elements and wiring and taking down old unserviceable one complete all as direrected by Engr-in-Charge. Make: Cat No. LC1F630 of Schnieder or its techno commercial Equivalent in Siemens/ABB/L&T/GE

Supply & fixing of 3 pole power contactor AC/DC Control ,Ie -350Amps current rating,415 volts,50Hz suitable for existing one and including necessary fixing elements and wiring and taking down old unserviceable one complete all as direrected by Engr-in-Charge. Make: Cat No. LC1F265 of Schnieder or its techno commercial Equivalent in Siemens/ABB/L&T/GE

SUN LIGHT HOUSE

Sri Balaji Enterprises

DPS sales and services india

L and S ENTERPRISES

STANDARD AGENCIES

SANJEEV CONSTRUCTIONS

Srinivasa Consructions

omsai thermax engineers