SPL REPAIR TO 08 BATHROOMS 03 X BATHROOMS IN BLDG NO P7 OF C COY 02 X BATHROOMS IN BLDG NO P4 AND 03 X BATHROOMS IN BLDG NO P5 OTM ACCN OF 21 KUMAON AT NAMS

Amount

Taking down Chowkhat or frame not exc 1.5 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5 sq.m but not exc. 4 sq.m each complete all as specified and directed.

Material and labour for framed work as in doors of angle or other section complete drilled for fixing sheeting with all fitting and fixture complete all as specified and directed.

Material and labour for 35 mm thick factory made solid PVC (Wood Polymer composite) moulded gauged door shutter with wire mesh in any number of division with brown wood grain texture, including S.S wire mesh shall be fixed with 15 x 15 Square tubes in is rails with screwing 8 x 28 mm heat metal zink coated screws can be remove or fix again after changing of wire mesh when needed. The density shall be as per manufactures instructions complete all as specified and directed.

Material and labour for Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Kg/Cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. Note : Stainless steel butt hinges and necessary S.S screws shall be paid separately.

Material and labour for Factory made single extruded WPC (Wood Polymer Composite) solid door frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/Cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant including making good after complete all as speicifed and directed.

Material and labour for Factory made single extruded WPC (Wood Polymer Composite) solid door frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/Cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant including making good after complete all as speicifed and directed.

Supply and fixing of factory made solid PVC moulded door shutter with wood free solid board , 28 to 30 mm thick (stiles) with 2, 4 or 6 rised panel design with 5mm thick 3D wood laminated moulded PVC sheet Polyurethane painted on the front and back face with 19 guage thickness using MS square tubing supplying and fixing of 19mm x19mm frame structure complete all as specified & directed

Supply and fixing of Solid PVC Door frame of sizes 95mm x 50 mm made out of 5 mm laminted both side colour PVC sheet reinforcement with MS square tube,supplying & fixing in opening as per specification & drawing complete all as specified and directed

Supply and fixing of Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Material and labour for box type steel window 1.25 mm thick made of ERW tube P-Section of size 60 x 25 mm double rebated outer frame comprise of glazed skeleton shutter(two gauged shutters and two glazed shutter) of ERW tube P-Section size 50 x 20 mm and 1mm thick one/two Nos openable leaf consisting of two Nos sash bar of T-Section 20x3mm welded to frame with one No Vertical mullion of ERW box type T-Section of size 60 x 25 mm and 1.25 mm thick and FI 2 mm thick welded / screwed to frame for fixing of glass including fittings and fixture like Handle, Tower Bolt, stopper, cleat, pintal hinges, hold fast etc. (i) Hold Fast, 150mm long of 120mm x 3 mm made to shape -04 Nos per window. (ii) Handle of Z sec 20mm x 25mm, 100 mm long -1 No per leaf (iii) MS Tower bolt 150mm long - 2 No per leaf (iv) Z Sec 20mm x 25 mm, 100 mm long stopper - 1 No per leaf (v) Cleat 55 mm long of hollow square 15mm x 20mm x.63mm welded to hinge -1 No per leaf. (vi) MS Pintal hinges of size 75mm x 12mm - 2 Nos per leaf . (vii) 10 mm square guard bar, 10 cm centre to centre. (viii) 25x4 mm flat iron all around for joint of both frame. Note : Quated rates are deemed to be Inclusive of taking down old steel / wooden window and making good dismantled portion with PCC 1:2:4 type B0 incl hold fast PCC (four No’s for Each window) & around required plaster in CM 1:4 and matching with existing finishing complete all as specified and directed.

Supply and fixing of 3mm thick, sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.5 Sqm in each pane fixed incl hacking out glass old complete all as specified and directed.

Supply and fixing of 100mm long stainless steel butt hinges welded or screwed , complete all as specified and directed.

Supply and fixing of aluminium handle cast type anoodised 150mm size ISI mark complete all as specified and directed.

Supply and fixing of 150mm aluminium anodised barrel tower bolts of extruded section and fixed ISI marked complete all as specified and directed.

Supply and fixing of 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

Supply and fixing of in repairs 300mm long mild steel ordinary rat tail rod pattern spring with roller plate including fixing with nails/ bolts or welded complete all as specified and directed.

Dismantling of brick works in cement mortar complete all as specified and directed.

Material and labour for brick work with sub class 'B' bricks in CM (1:6) straight or curved on plan exc 6 mtrs mean radius, complete all as specified and directed.

All as per item no 19 above but except bricks.

Material and labour for brick work with sub class ‘B’ bricks (old size brick) straight or curved on plan to any radius in half bricks thick walls built in CM 1:4 complete all as specified and directed.

Taking down cement plaster on brick/stone/concrete walls incl racking out joints etc,hacking for key, scrubing down with water etc & dispose off debris upto a distance n exc. 500 m where directed complete all as specified and directed.

Material and labour for 15mm thick cement plaster in CM 1:4 on fair faces of brick or concrete work and finishing the surface even and smooth (without using extra cement) incl WPC @3% weight of cement complete all as specified and directed. Note-WPC will be measured and paid separately under appropriate items

Material and labour for 15mm thick cement plaster in CM (1:6) on fair faces of brick or concrete surfaces and finishing the surface even and smooth (without using extra cement) etc. complete all as specified and directed.

Material and labour for 10 mm thick cement plaster in CM (1:3) on concrete surfaces of ceiling and finishing the surface even and smooth (without using extra cement) etc complete all as specified and directed.

Supply only water proofing compound ,ISI marked, complete all as specified and directed.

Material and labour for preparation of newly plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

Material and labour for preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of primer including 1mm thick wall care putty complete all as specified and directed.

Material and labour for preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

Material and labour for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

Material and labour for applying two coat of cement base paint on walls, pillars cornices etc surface incl preparation of old plastered surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and incl filling necessary where required with putty as in pathces or nail holes obtain smooth finish using sand paper and matching the existing surface complete all as specified and directed.

Material and labour for applying two coat of oil bound distemper on walls, pillars cornices etc surface incl preparation of old plastered surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and incl filling necessary where required with putty as in pathces or nail holes obtain smooth finish using sand paper and matching the existing surface complete all as specified and directed.

Material and labour for Preparation of old surfaces of ceiling includinng scrapping down smoke ,soot,and efflorescent salts and treatings oil and gresy spots, brooming down or steel wire brushing removing nails making good holes cracks etc on plastered or unplastered surfaces and applying two coat of white wash on ceiling surface complete all as specified and directed.

Material and labour for Applying 2 mm thick wall care putty to achieve even and smooth surfaces on old scraped surfaces or new plasterd surfaces and obtain using sand paper complete all as specified and directed. Note-Entire splashes in floors shall be cleaned immediately after completion of periodical services.

Material and labour for preparation of steel surfaces of exceeding 10cm width or girth and applying one coat of synthetic enamell paint complete all as specified and directed.

Material and labour for repairing of RCC projection, chajjas, facia,bands, shelves, beams, slab , RCC railing, balcony and similar works by dismantling of loose/ disintegrated portion RCC at any height and in any sitution floor (including provn of support, formwork and welding of reinforcement if required with wire mesh of weight 3 kg/ sqm and dubbing/ filling with PCC (1:2:4), type B-0, using 12.5 mm graded aggregate,15 to 25 mm thick after applying cement slurry @ 3 kg/sqm, finished even and smooth to desired shape and applying two coats of wheater proof emulsion paint to match with existing surfaces complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 15mm bore of pipe incl taking down old pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 20mm bore of pipe incl taking down old pipe complete all as specified and directed.

Supply and fixing of 15mm bore tubing medium grade galvanised steel tubing with all fittings and fixed to walls, ceiling and in floor incl cutting, chasing in wall, floor or ceiling and making goodin CM 1:3 incl taking down old pipe complete all as specified and directed.

Supply and fixing of 20 mm bore tubing medium grade galvanised steel tubing with all fittings and fixed to walls, ceiling and in floor etc. incl taking down old pipe complete all as specified and directed.

Supplying , fixing & Hoisting and fixing in position and connecting, in repairs, 1000 litres capacity rotational moulded polyethylene water storage tank (cylindrical, vertical with closed top) including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed all as specified in SSR Part-I complete all as specified and directed. make Sintex

Material and labour for Demolition of reinforced cement concrete of cover slab/cooking platfrom and RCC roof tank etc complete all as specified and directed.

Material and labour for 50mm thick cement concrete (1:2:4) type B1, using 20mm graded stone aggregate laid over roof as in platforms for water tanks, finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for rendering 15mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for cement concrete (1:2:4), type B-1, using 20mm graded stone aggregate in window cills, lintel band, bed block, copings and the like including weathering, slightly rounded or chamfered angles and throating, Including necessary form work complete all as specified and directed.

Supply and fixing in repair vitreous china urinal, half stall complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement incl flush pipe, grating, waste coupling and union for discharge pipe complete all as specified and directed.

Supply and fixing of in repair vitreous china ware over counter ovel wash hand basin, any colour, size 570 x 450 mm size including cutting for and pinning ends of brackets or erecting stand including 32 mm dia PVC waste pipe (Plain) ,32mm dia Chromium plated waste coupling complete all as specified and directed.

Supply and fixing in repairs of Vitreous China Squatting pan 'orissa pattern size 580x440 white with integral foot rests incl `P' or `S' trap, front or back inlet including connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including concrete and making good to floor complete all as specified and directed.

Supply and fixing , in repair, of vitreous china floor mounted single peace WC with PP soft close seat cover , hinges accessories set as per size 375x660x800mm with cistern fitting (including fixing bolts flush pipe) complete all as specified and directed.

Supply and fixing in repair of 8mm dia brass, chromium plated health faucet (Hand shower) with 01 meter long flexible tube and wall hook.

Supply and fixing in repair of , overhead shower 200mm x 200mm square shape single flow (ABS body chrome plated with gray face plate ) including shower arm 190mm long with rubit cleaning system complete all as spd and directed

Supply and fixing in repair of 15mm bore dia fancy type chromium plated long body bib tap with crutch or buttewrfly handle screwed down to iron pipe with all fittings complete all as specified and directed.

Supply and fixing in repair of 15 bore dia chromium plated Stop cock/Angle cock screwed down high pressure with crutch or butterfly handle & screw both end for iron pipe or for unions complete all as specified and directed.

Supply and fixing in repairs of 15 mm bore dia fancy type chromium plated long shank and cup stop valves (Concealed type), cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

Supply and fixing in repairs of 15mm bore dia swan neck fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

Supply and fixing in repairs of 10 litre capacity PVC valveless. Syphonic action type, flushing cistern, low level, with inlet, ball valve, float, and handle and brackets including 32mm dia flush pipe of polyethylene of high density for low level cistern complete all as specified and directed.

Supply and fixing of 450mm long PVC connections with PTMT nuts of suitable for 15mm bore dia pipe complete all as specified and directed.

Supply and fixing brass chromium plated tubular towel rack 20 mm dia 60 cm long between flanges complete all as specified and directed.

Supply and fixing of, Chriomium Plated soap dish holder complete all as specified and directed.

Supply and fixing of, chromium plated glass corner (Corse) size 300mmx300mm complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving n. exc 15 cm thick below or above ground level & dispose off debris upto a distance n. exc. 100 mtrs where directed complete all as specified and directed.

Material and labour for 75mm thick PCC 1:3:6, Type C-1 (using 20mm graded aggregate) as in Plinth protection, making even and smooth surface without using extra cement complete all as specified and directed.

Material and labour for reinforced precast cement concrete 1:2:4 Type B1 (using 20mm graded aggregate) as in cover slabs (for drain.) , and similar articles with plain faces set in cement mortar 1:6 complete all as specified and directed.

Material and labour for TMT mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips Quality confirming to FE 500D complete all as specified and directed.

Material and labour for non skid ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 09 sqm but not exceeding 0.11 sqm, in floors etc. laid over 15mm thick screed bed in cement mortar 1:6 and jointed in neat cement slurry and pointed in white or coloured cement to match incl dismantling / demolition and rubbish off the primises etc complete all as specified and directed.

Material and labour for glazed ceramic coloured tiles of size 450mm x 300mm x 7mm on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including rendering 10mm thick in cement mortar (1:4) , incl dismantling / demolition and rubbish off the primises etc complete all as specified and directed.

Material and labour for Non skid ceramic pattern or any colour coloured tiles 7 to 8 mm thick (Square or rectangular) area of each tile exc 0.18 Sqm but not exceeding 0.36 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishesincl dismantling / demolition and rubbish off the primises etc complete all as specified and directed.

Material and labour for Non skid ceramic pattern or any colour coloured tiles 7 to 8 mm thick (Square or rectangular) area of each tile exc 0.18 Sqm but not exceeding 0.36 Sqm, as in skirting ,dados in vertical surfaces etc and including 10mm thick cement plaster 1:4 incl dismantling / demolition and rubbish off the primises etc complete all as specified and directed.

Material and labour for heavy Glazed Vitrified Tiles in steps and risers 10mm thick size 300mmx1200mm , 200mmx1200mmor and landiing as in floors (in treads, landing etc ), set, jointed and pointed in neat cement slurry with white cement and pigment laid over and including screed bed or bedding layer of 15 mm thick in cement mortar (1:6) inlcuding demolition complete all as specified and directed.

Material and labour for 15-18mm thick black granite stone (of any type) machine cut, bedded and jointed with gray cement slurry and pointed with white cement with admixture or pigment to match the shade of stone in window cills, jams,cooking platform pillars etc.laid over and including rendering 10mm thick in cement mortar (1:4), jointed with grey cement slurry mixed with pigment to match the shade of the slab including rounding and rubbing and polishing complete all as specified and directed.

Material and labour for 25mm thick cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate as in sub base to receive floor finishes complete all as specified and directed.

Material and labour for 200mm bore dia RCC Class NP 2 pipes laid and jointed with collar incl dismantling of old pipe by excavation, digging, bearking up etc, complete all as specified and directed.

Material & labour for PCC 1:3:6 type C-2 (using 40mm graded granite stone aggregate) as in bed of 200mm dia RCC pipes including forming cradels after they are laid and tested in complete all as specified and directed.

Dismantling brick tiles or terracing single layer as in roofing complete all as specified and directed.

Demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and directed.

Material and labour for 50mm average thickness PCC 1:2:4 type B1 (using 20 mm graded stone aggregate as roof padding ,hunching, sub base floor, even and smooth without using extra cement for further treatment complete all as specified and directed.

Material and labour for preparation of roof surface & applying evenly a tack coat of industrial bitumen primer 85/25 grade @ 1.2 Kg/Sqm including APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced wih polyster non wove fabric (wt not less than 150 gms/sqm) applied on primed surface by forced application of heat and roller, joints to be touched hot and width of overlaps not be less than 150 mm complete all as specified and directed.

Material and labour for 40 mm thick brick tiles laid and joints in cement mortar (1:3) over 25 mm thick screed bed in cement morter 1:4 and flush pointing as work proceed complete all as specified and directed.

All as per item No 79 above but except bricks tiles.

Material and labour for plain cement concrete (1:5:10) type E-2 using 40 mm graded stone aggregate as in filling in sunken floors including demolition of cement in concrete (unreinforced) in ground floor and pavings any thickness (below or above ground level) of complete as specified and directed.

Material and labour for Water proofing treatment to sunken floors of kitchen, toilets, laboratories, bath and WC's etc shall be as under :- (a) Application of Two component Acrylic modified cementitious coating (i) The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil, surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or milling to remove cement laitance, existing coatings and achieve a gripping profile that is clean, dry and free from laitance and any other form of surface contamination. The installation instructions in manufacturer’s published literature should be strictly complied with, including but not limited to the following :- (ii) Chipping out any visible cracks in “V-Groove” pattern as applicable. Special attention on this part. Cleaning of cracks & then filling those cracks with SIKA latex SBR 100 putty/ Dr Fixit 302 SBR latex / Perma latex SBR / FOSROC Nitabond SBR latex / Asian Paints latex as required. Final cleaning of surface with power grinder, wire brush, hair brush & vacuum pressure if required. (iii) Dampen all surfaces immediately ahead of application of Acrylic modified Cementitious coating of Sika Top Seal – 107 / Brush Bond FOSROC/ Dr Fixit/ STP/CICO. (iv) Whilst the surface is still damp from saturation (S.S.D), apply one coat of Acrylic modified Cementitious coating of Sika Top Seal – 107 / Brush Bond FOSROC/ Dr Fixit/ STP/CICO of viscosity as per manufacturer’s instructions. (v) Apply Glass Fabric Sheet of Sika Fab 1 / FOSROC/ Dr Fixit/ STP whilst the first coat is wet.

(vi) Once touch dry, apply second coat of Acrylic modified Cementitious coating of Sika Top Seal – 107 / Brush Bond FOSROC/ Dr Fixit/ STP/CICO of viscosity as per manufacturer’s instructions on the entire area. (vii) Second coat shall be applied after 6-8 Hrs of application of previous coat and in the direction right angle to the previous coat. (viii) The waterproofing coating should be taken to a height minimum 300 mm above the finished floor level on the vertical surface. (ix) It is essential to cure Acrylic modified Cementitious coating immediately after application (minimum 6-8 Hrs drying) for a minimum of 3 to 5 days to ensure full cement hydration and to minimize cracking. (x) A protection plaster (12-15mm thick) in CM 1:3 admixed with appropriate Integral water proofing compound has to be applied on the walls. Admixture : Sika Plastocrete Plus / FOSROC / Dr Fixit / STP / CICO confirming to IS 2645. Providing and applying a protection screed of 50mm thick 1:4, cement sand mortar admixed with Sika Plastocrete over the applied water proofing coating on horizontal surfaces. Admixture : Sika Plastocrete Plus / FOSROC / Dr Fixit / STP / CICO confirming to IS 2645 (xi) All the corners and joints should be pre-treated with an elastic waterproofing sealing tape with a Woven bonding mesh on each surface and an elastic expansions zone in the centre of Make Sika Seal Tape S/FOSROC/Dr Fixit/STP.

(xii) The membrane has to be protected in accordance with the manufacturer’s recommendations until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and make repairs in accordance with manufacturer’s recommendations (xiii) Waterproofing treatment has to be carried out through authorised applicators (b) All the joints of pipes and traps within the sunken portion shall be sealed properly by epoxy sealant. (c) Al CI traps in sunken slabs to be enclosed with PCC 1:1.5:3 (min 15cm) All-round. (d) The sunken portion shall be filled with PCC 1:5:10 type E-2 (using 40mm stone aggregate) complete all as specified (e) Providing drainage spout pipe GI 40 mm dia bore light grade upto outside of outer wall (Approx 450 mm to 600 mm long) including cutting to existing wall and making good the disturbed surface complete all as specified and directed. (f) Providing 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in flooring for laying floor finish all as specified. Note: Items No 82.02 (d), (e) & (f) shall be measured and paid separately.

Supply and fixing of in repair 40mm dia GI pipe medium grade 45 cm long for a spout pipe including necessary cutting of existing beam/slab and fixing with cement concrete 1:2:4 complete all as specified and directed.

Supply and fixing, in repair, of 25 mm dia, 1 mm wall thickness stainless steel fancy type, decorative curtain rod with decorative ball type side brackets (As per Sample) fix with wooden gutties complete all as specified and directed.

Supply and fix in repair PVC (SWR) nahani/ floor trap, plain with grating with or without waste hole including jointing with solvent cement 75mm dia etc complete all as specified and directed.

Supply and fixing of 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints and necessary fittings laid in floors/Wall or trenches incl taking down old pipe complete all as specified and directed.

Supply and fixing of 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints and necessary fittings laid in floors/wall or trenches incl taking down old pipe complete all as specified and directed.

Supply and fixing of, 75mm bore PVC (SWR) bend, any radius with access door complete all as specified and directed.

Supply and fixing of, 110mm bore PVC (SWR) bend, any radius with access door complete all as specified and directed.

Supply and fixing of, 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and directed.

Supply and fixing of 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

Material and labour for damproofing to wall with two component Acrylic polymer cementitious water proof elastomeric coating for grade mix to form uniform slurry and apply with paint brush as first coat then laying a layer of fibre glass mesh cloth as first coat is still green with overlap of joints of fibre mesh not less than 100 mm then finally apply second layer mix by brush to entire surface of container covering 0.6 - 0.75 Sqm/Kg at 1 mm thickness in two coat depending on the level of substrate and curing it for minimum 3 days. Note : Quoted rate shall be deemed to be inclusive of materials all labours, tools and plants, scaffolding and working upto height 6 metre etc. Make : Pidilite Industries Ltd/Fosroc India Ltd/IWL India Ltd, BASF/T-Guard ANTC of make- Trermax, complete all as specified and directed.

Taking down aluminium/copper point wiring from existing conduit / batten (light, fan, socket or power) complete such as switches, ceiling rose, pendent, regulators, socket, light fittings etc and removing material from site and making good the disturbed surface of wall / floor etc, complete all as specified and directed

Material and labour for Point wiring in replacement with 1.5 Sqmm (Nominal Area) 1100 Volt Insulated, FRLS unsheathed multi stranded flexible copper conductor cable in NEW PVC concealed conduit not less than 20 mm dia 1.5 mm thick for one light / fan point controlled by one switch (including cutting chases and making good the distributed surface ) and fixing new 3 mm thick hylem sheet top cover, sheet screws and 1.6 mm thick GI sunken boxes included 1.5 sqmm stranded copper conductor with green PVC insulation earth contunity conductor connected to comman earth dolly etc. complete all as specified and directed for the following:- NOTE : The cost of sunken boxes and bakelite sheet is included in the quoted rate)

One light / bell piont/ Fan point/ Exhaust fan point controlled by one 5 Amp switch one way complete all as specified and directed

All as per Srl item No 94 above but on the Indepedant board complete all as specified and directed

All as per Srl item No 94 above but on the same board complete all as specified and directed

All a per item No 94 above but with 2.5 Sq mm size cable multi stranded FRLS copper wire unsheathed for one 3 pin socket outlet 15 Amps on independent board including continuous earth wire of PVC insulated 2.5 Sq mm copper solid conductor connecting to common earth dolly complete all as specified and directed.

Supply and fixing in replacement switch piano type 6 Amps one way 230 volts AC complete all as specified and as directed.

Supply and Fixing in replacement socket outlet 5 pin, 6 Amps flush type 230 volts AC complete all as specified and as directed

Supply and Fixing in replacement switch piano 16 Amps type one way 230 volts AC complete all as specified and as directed

Supply and Fixing in replacement socket outlet 6 pin 6/16 Amps multi purpose flush type 230 volts AC complete all as specified and as directed

Supply and fixing in replacement ceiling rose 65/50 mm two to three terminals complete all as specified.

Supply and fix in replacement MCB 40 Amps single pole with neutral, AC 230 Volts complete all as specified and directed.

Supply and fix in replacement MCBs single pole (SP) 5 to 32 Amps with 10 KA breaking capacity of 'B' series in distribution boards complete all as specified and directed.

Supply and fixing in replacement Sheet metal enclosure for DB's when MCB's to be used single door factory made flush fixed complete with 200 Amps rated busbar 240 Volts single phase 8 ways complete all as specified and directed.

Supply and fix in replacement for sub main wiring with two run of single core (FRLS) PVC insulated and unsheathed cable with copper conductor (Multi strand) having nominal area 6.0 Sqmm drawing into and including PVC non metallic rigid conduit medium grade of adequate size and making electric connections including one run (FRLS) PVC insulated single core copper conductor cable 6.0 Sqmm as a earth continuity conductor(green colour) and including non metallic medium grade rigid PVC conduit, including cutting chases in brick wall, and making good to match the existing specifications complete all as specified and directed. Note :- (i) Rates are deemed to be included cutting and making holes in wall/floor for passing in or through conduit (ii) Two run of 6.00 sqmm single core (FRLS) PVC insulated copper conductor cable, one run of 6.0 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of suitable size will be measured as a one unit.

Supply and fix in replacement for sub main wiring with two run of single core (FRLS) PVC insulated and unsheathed cable with copper conductor (Multi strand) having nominal area 4.0 Sqmm drawing into and including PVC non metallic rigid conduit medium grade of adequate size and making electric connections including one run (FRLS) PVC insulated single core copper conductor cable 4.0 Sqmm as a earth continuity conductor(green colour) and including non metallic medium grade rigid PVC conduit, including cutting chases in brick wall, and making good to match the existing specifications complete all as specified and directed. Note :- (i) Rates are deemed to be included cutting and making holes in wall/floor for passing in or through conduit (ii) Two run of 4.00 sqmm single core (FRLS) PVC insulated copper conductor cable, one run of 4.0 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of suitable size will be measured as a one unit.

Material and labour for replacement of lamp holder insulated body with 9 Watt LED Bulb, back plate batten/angle type for batten fitting fixed on bakelite sheet 100mmx100mm 230V AC cool day light 6500K having maximum height 1020mm heavy duty complete all as specified and directed.

Supply and Fixing of exhaust fan, steel body single phase 230V of size 300 mm sweep with blades, frame and louvers complete all as specified and directed.

Supply and fixing in replacement of LED T-8 tube light fitting with sinle side connection LED tube rod 18/20 W, 4 Feet made of CRCA sheet steel box type including bipin holder and connection with PVC insulated three core 23/0.0076 twisted copper cable from ceiling rode to light fitting complete all as specified and directed.

Supply and Fixing of LED Street Light Luminaire 25 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens complete all as specified and directed.

Supply and fixing of security light mounting bracket made out of GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat of size 40 x 6 mm and nuts and bolts and painting with aluminium paint, complete all as specified and directed.

Supply and Fixing in replacement of single pole and neutral sheet metal enclosures with two pin & earth plug and socket complete with one singlr pole MCB of 20 amps complete all as specified and as directed.

Supply and Fixing of Storage water heater (Geyser) of 25 litre capacity 230V AC, 50HZ having element of 2 KW of COPPER/INCOLOY alloy , Rust proof outer body,high density PUF insulation, BEE 5 Star Rated ,Inner tank of SS 304 which can sustain pressure of minimum 7 Bar working pressure and having multifunction safety valve plug top , making electric and water connection complete all as specified and directed.

Supply and fixing in replacement of sheet steel enclouser distribution boards, double door factory made TPN Vertical 4 way 3 phase 415 volts 4 way with 200 amps rating copper bus bar and PVC insulated copper jumpers of suitable size from the MCCB to the out going circuits one incoming MCCB and 12 outgoing MCBs circuits comprising of 3 phase 4 wire of suitable rating with the following accessories :- (a) MCCB 100 amps, 25 KA, TP, 415 volts, 50 Hz= 01 No. complete all as specified and directed. (Note:- Out going MCB shall be measured and paid for separately)

M/s Vijay Construction Co. (BID ID -3510862)