PROVN OF TEMP STRUCTURE LPG STORE ROOM 02 X TOILET 01 X OPEN STORE SHED AND SPL REPAIR TO BLDG AT VARIOUS LOCATIONS UNDER AGE BR I AND AGE EM OF GE BENGDUBI

Amount

Excavating in trenches in soft/loose soil n. exc 1.5m wide and n. exc1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10sqm on plan and n.exc 1.5m in depth and getting out. in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Excavating in post holes( or similar holes) each n exc 0.50 cum , getting ut,returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft/ loose soil complete all as specified and directed.

Surface dressing n.exc 15 cm deep in soft/loose soil complete all as specified and directed.

M&L for sand cushioning for protection of underground cable, consolidated and compacted with clean dry sand complete all as specified and directed.

M&L for Sand filling under floors or in foundation including watering and consolidated and compacted with clean dry sand complete all as specified and directed.

Removing excavated material (soil) n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

M&L for hardcore of gauge n.exc. 63 mm,with broken stone and boulder, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surfaces complete all as specified and directed.

M&L for cement concrete type D2, 1:4:8 using 40mm graded stone aggregate as in foundations filling and mass concrete complete all as specified and directed.

M&L for PCC 1:2:4 type B2, using 40mm graded stone aggregate, as in foundation filling & mass concrete complete all as specified and directed.

M&L for PCC type C1,1:3:6 using 20mm graded crushed stone agg,in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for reinforced cement concrete design mix M 25 grade using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete design mix M 25 grade using 20 mm graded stone aggregate as in chajja , shelves and like etc. complete all as specified and directed.

M&L for reinforced cement concrete design mix M 25 grade using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for reinforced cement concrete design mix M 25 grade using 20 mm graded stone aggregate as in Columns, pillars, piers, posts and struts complete all as specified and directed.

Supply only integral water proofing compound liquid grade conforming to IS-2645 complete all as specified and directed. (Pidiproof of Dr.fixit or equivalent)

M&L for brickwork with old size fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for brickwork with old size fly ash bricks, straight or curved on plan to any radius as in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M&L well burnt old size sub Class ‘B’ bricks, laid flat, in trenches for cable protection complete all as specified and as directed by the GE.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams; and similar work; vertical to rough finished surface complete all as specified and directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work;not exceeding 200mm thick (Horizontal or sloping) rough finished surface flat complete all as specified and directed.

M&L for formwork to chullah hoods, chajjas, troughs and similar items in cluding edges complete all as specified and directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished surfaces of concrete, square, rectangular or polygonal in shape complete all as specified and directed.

S&F 30mm thick 2nd class hard wood glazed and skeleton factory made shutter open rebated and prepared to receive glass, gause etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers edges of framing plain chamferred or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR part-I, Sec-08, Clause 8.20(a), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 30mm thick factory made flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 35mm thick factory made flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides kiln seasoned and chemically pressure treated complete all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frame) area not exc. 1.5sqm each, including cutting holes for removing the hold fast,making good disturbed surfaces and removing materials from site of work complete all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frame) exc. 1.5 sqm and n.exc 4 sqm each, including cutting holes for removing the hold fast, making good disturbed surfaces and removing materials from site of work complete all as specified and directed.

M&L for Factory Made Solid PVC Moulded Door Shutter With Particle Board Core , 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing. (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) complete all as specified and directed

S&F 100mm Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed.

S&F 200mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and direcetd.

S&F 100mm Butt hinges,medium weight, cold rolled mild steel, complete all as specified and directed.

S&F 100mm Butt hinges, cast brass,with mild steel hinge pin, bright polished and fixed, typeB-11 complete all as specified and as directed.

S&F Continuous (piano) hinges Width of flaps (when open) in 30mm,mild steel, bright finish or elec?trogalvanised complete all as specified and directed.

S&F 100mm Extruded brass handles,fabricated type polished complete all as specified and directed.

S&F 150mm size aluminium handle cast type complete all as specified and directed.

S&F tubular towel rail 20mm dia type brass chrormium plated 600mm long between flanges complete all as specified and directed.

S&F in repair tubular towel rail 20mm dia type brass chrormium plated 600mm long between flanges complete all as specified and directed.

S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staplescomplete all as secified and as directed

M&L for MS framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc. 22.5cm and n exc 30cm long and dia of neck from 11mm to 15mm complete all as specified and directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for TMT bars but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for rolled mild steel works in Plates (plain or chequered) channels, square conforming to Fe-410-W(Gde E-250) quality Bcut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment etc complete all as specified and directed.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe -410-W(Gde-E-250) quality-A. complete all as specified and directed.

M&L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 conforming to Fe 410 -W (Gde E- 250) quality A complete all as specified and directed.

S&F steel window with side hunge shutters including projecting type hinges with steel handle and steel peg stey, tower bolts etc. complete with glazing bars dovetailed or welded complete all as specified and directed.

S&F steel window with side hunge shutters including projecting type hinges with steel handle and steel peg stey, tower bolts etc. complete without glazing bars dovetailed or welded complete all as specified and directed.

M&L for 1.25mm thick pressed steel door frame of size 165mm x 60mm with one or more rebates including necessary fixing lugs , hinges, lock strike plate etc complete all as specified and directed.

M&L for 1.25mm thick pressed steel door frame of size 105mm x 60mm with one or more rebates including necessary fixing lugs , hinges, lock strike plate etc complete all as specified and directed.

M&L for anodised aluminium snap grid (SIZE-605x605MM) frame work for false ceiling complete all as specified and directed.

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

S&F Hard drawn steel wire fabric in available size Weight per square metre Not exc 4 kg complete all as specified and directed.

S&F Pre- painted coloured trapezoidal profiled Galvalume/ Zincalume sheet with min thickness 0.50mm TCT confirming to IS - 513(AZ-150 GSM, Al Zn allay metalic coating with 550 Mpa yield stress as per AS-1397) as in roof covering/cladding to wall, fixed with self tapping screws colour exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron primer and 5 micron polyster back coat applied over 5 micron primer , all fixed with galvanized self drilling self tapping fastner (12-14 x 55 with EPDM seals) complete all as specified and directed.

S&F Pre- painted coloured plain sheet Galvalume/ Zincalume sheet with min thickness 0.50mm TCT confirming to IS - 513(AZ-150 GSM, Al Zn allay metalic coating with 550 Mpa yield stress as per AS-1397) as in roof covering/cladding to wall, fixed with self tapping screws colour exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron primer and 5 micron polyster back coat applied over 5 micron primer , all fixed with galvanized self drilling self tapping fastner (12-14 x 55 with EPDM seals) complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks,etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F 4mm thick non asbestos fiber cement building boards, fixed or laid /inserted to timber /GI /Aluminium frame-work with screws complete all as specified and directed.

M&L 19/20mm thick Veneered particle board,interior grade, solid core,medium density general purposes type with commercial face veneers type 'BB' complete all as specified and directed

M&L for 18mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade of granite over and including 15mm thick bedding layer in cement mortar 1:4 including grinding and polishing complete all as specified and directed.

M&L for 75mm thick PCC type D2,1:4:8 using 40mm graded stone aggregate as in sub base floor complete all as specified and directed.

M&L for 75mm thick PCC type C2,1:3:6 using 40mm graded stone aggregate as in sub base floor complete all as specified and directed.

M&L for 75mm thick PCC type C2,1:3:6 using 40mm graded stone aggregate as in plinth protection finished even and smooth using extra cement.Joints to be given at every 3m interval and corners of buildings and fitted with bituminious mastic or equivalent filler complete all as specified and directed.

M&L for 40mm thick cement concrete type B-1, 1:2:4 (using 20 mm graded stone aggregates) as in flooring, finished the surfac even and smooth without using extra cement complete all as specified and directed.

Dismantling of floor, hearth or wall tiling / Paving Blocks including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.

M&L for sheet glass, 4mm thick, ordinary quality and glazing with oil putty in squares n exc. 0.50 Sqm each pane complete all as specified and directed.

M&L for preparation of untreated new wood/wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint any tint all as specified and directed.

M&L for two coats of synthetic enamel paint over one coat of red oxide on new steel surfaces of any description over 10cm in width or girth including preparation of surfaces complete all as specified and directed.

M&L for 40mm dia GI pipe Light grade with all necessary fittings laid in trenches, fixed to wall/pole/under road/floor etc for cable protection complete all as specified and as directed.

S&F medium grade galvanized steel tubing (concealed) with all fittings & fixed complete to walls & ceiling or laid in floors 15 mm dia bore pipe (including in short length) complete all as specified and directed.

S&F medium grade galvanized steel tubing (concealed) with all fittings & fixed complete to walls & ceiling or laid in floors 20 mm dia bore pipe (including in short length) complete all as specified and directed.

Taking down steel tubing & connections including cleaning for refixing serviceable pipe or removal balance pipe of 15 mm dia bore complete all as specified and as directed

Taking down steel tubing & connections including cleaning for refixing serviceable pipe or removal balance pipe of 20 mm dia bore complete all as specified and as directed

Dismantling water tanks and removing to store exc 250 ltr but not exc 500 ltr capacity complete all as specified and as directed

S&F rotational moulded PVC water storage tank 500 ltrs capacity conforming to IS-12701(1989) cylindrical vertical type double-layered with closed top (thereated) including inlet,outlet and wash out holes of approved make hoisted and fixed in position all as specified in SSR Part I etc completge all as specified and directed.

S&F fancy type stop valve cast copper allow screw down high pressure with crutch or butterfly handle screwed both end form iron pipe or for union and fixed of size 15mm dia complete all as specified and directed.

S&F in repair fancy type stop valve cast copper allow screw down high pressure with crutch or butterfly handle screwed both end form iron pipe or for union and fixed of size 15mm dia complete all as specified and directed.

S&F in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 20mm bore and fixed as in repair complete all as specified and directed.

S&F Ball brass valves, high pressure, with polyethene float and fly nut complete, screwed for GI pipe or brass ferrule of 20mm bore complete all as specified and directed.

S&F ball valves for 20mm bor dia of pipe high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0mm-210gms./25mm-455gms/ 40mm - 690 gms) complete all as specified and directed.

S&F grating doom 100mm dia of PTMT (minimum weightt 25 gm) for floor trap/nahani trap, complete all as specified and directed.

S&F in repair PVC connections pipe ,15mm dia size with PTMT nuts of length 450mm complete all as specified and directed.

S&F cast iron bend (Sand cast) of any radius with oval access door including jointing with cement joints for (100 mm bore) complete all as specified and directed.

S&F 75mm PVC (SWR) as in drain pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F 110mm PVC (SWR) as in drain pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends with rubber ring joints any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends with rubber ring joints any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed.

S&F 110mm bore PVC (SWR) vent cowl complete all as specified and directed

S&F 110mm bore PVC (SWR) `P' or 'S' trape complete all as specified and directed.

S&F PVC (SWR) floor trap 75mm dia , plain with grating including jointing with solvent cement to waste pipe complete all as specified and directed.

S&F in repair sinks made of stainless steel 01mm thick kitchen or laboratory with plugs, washers and wastes;including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed

S&F in repair Low density polyethylene (LDPE) pipes bore of pipe in 32mm of pressure rating 6 kgf/sq. cm complete all as specified and directed

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings,dressed stonework and precast concrete articles complete all as specified and directed.

Demolition of Concrete un- reinforced of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling structural steel work in?cluding doors, gates but excluding framed truss etc. complete all as specified and directed.

Dismantling wall and ceiling board( fiber, pulp, insulation, etc.) or insulation board/slab/ blankets, any thickness, including cover fillets complete all as specified and directed.

S&F in repair mild steel Helical door spring 300mm long ordinary rat tail type incl roaller & roller plate complete fixed with screws to wooden frames or with welding to steel frames complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, partitions,windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make onforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. Note : (i) Weight of Aluminium sections as per actual or as per IS or as per Manufacturer which over is less, shall only be considered for payment. (ii) Cost of all the items/ accessories required for the entire completion of the work shall be deemed to be included in the quoted rate. However glass panes and particle board shall be measured and paid separately under respective items. (iii) The accessories required for partition as per directions of Engineer-in-charge shall be provided but weight for the same shall not be considered and no extra cost will be paid.

M&L for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge

M&L for powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as speecified and directed. Note : (i) Weight of Aluminium sections as per actual or as per IS or as per Manufacturer which over is less, shall only be considered for payment. (ii) Cost of all the items/ accessories required for the entire completion of the work shall be deemed to be included in the quoted rate. However glass panes and wirecloth shall be measured and paid separately under respective items. (iii) The accessories (Aluminium mongries etc) required to be provided for window, vents and doors as per directions of Engineer-in-charge shall be provided but weight for the same shall not be considered and no extra cost will be paid.

M&L for Glazed ceramic tiles coloured 300mmx 450mm , 6 to 7 mm thick as in skirting / dado, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surface etc complete all as specified and and as directed

M&L for Non Skid ceramic tiles (coloured) 7 to 8 mm thick , (square / rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes etc complete all as specified and directed

M&L for Non Skid ceramic tiles (coloured) 7 to 8 mm thick , (square / rectangular) area of each tiles exceeding 0.18 sqm but not exceeding 0.38sqm as in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes etc complete all as specified and directed

M&L for Non Skid ceramic tiles (coloured) 7 to 8 mm thick , (square / rectangular) area of ach tiles exceeding 0.18 sqm but not exceeding 0.38 sqm as in dado/skirting etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including rendering layer 10 mm thick in cement mortar 1:4 etc complete all as specified and directed

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size nconfirming to IS 15658-2006 of 60 mm thickness, M-35 Grade over and including 25mm thick sand filling layer well rammed and compacted complete all as specified and directed,

M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces and finishing surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in two layers 10mm +5mm in cement mortar 1:4 on external surfaces of brick work or concrete surfaces with using WPC finishing the surfaces even and smooth without using extra cement complete all as specified and directed. Note:- WPC will be measured and paid separately under respective item of this schedule.

M&L for rendering 20 mm thick in two layers of 10mm thick and 10mm thick in cement mortar (1:4) on fair faces of brick work or concrete surface finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacture nstruction etc. complete all as specified and as directed. Notes : WPC shall be measured and paid seperately under respective item of this schedule.

M&L for 5mm thick rendering in cement mortar 1:3 over/soffit of chajja/ceiling, finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new undecorated surface of wall and applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkai registant primer complete all as specified and directed.

M&L for prepration of old plastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed.

M&L for newly plastered surface of wall appying two coat of white or tinted oil bound distemper over one coat of alkali resistant priming paint including 01mm thick wall care putty etc complete all as specified and as directed.

M&L for complete removal of old plastered surface of walls and applying two coat of oil bond distemper white or any tint over a coat of primer etc complete as specified and directed.

Supply and laying of CPVC pipes outer diameter 20mm SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

Supply and laying of CPVC pipes outer diameter 25mm SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F in repair bib tap fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and directed.

S&F 15 mm bore pillar taps fancy type (long neck) cast copper alloy with hot & cold mixture chromium plated screwed down high pressure with or without letter hot or could with long screwed and shanks and fly nuts screwed for iron pipes complete all as specified and as directed.

S&F Health faucet (ABS Body) mild steel CP suitable for 15mm dia pipe with 1.25m long flexible tube and ABS wall hook incl making connection and fixed in position complete all as specified and directed.

S&F Shelf glass assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F in repair Vitreous china WHB 550x400mm size white flat back with brackets incl cutting or pinning ends of brackets (including waste pipe) incl Waste coupling of PTMT (32 mm dia) (half or full threaded) (Minimum weight 32mm 45gms/40mm-60 gm complete all as specified and directed.

S&F toilet paper holder brass chromium plated fixed with and including chromium plated brass screws with wooden plugs complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, approachs, dado/Partitions etc complete all as specified and as directed

M&L for providing and fixing PVC FALSE CEILING consisting of 600x600mm, 5mm (+0.25) thick plain ambossed PVC sheet of 600Kg/Cbm Density manufactured by ISO 9001-2008, certified company, used as panel insert in a frame work made using anodised aluminium T- section of sizes 1"x1" (25x25mm, 19 gauge or 1mm thick) in square pattern of grid sizes of 2'x2'(600x600mm). the aluminium frame work is supported from the ceiling with the help of "J" hook and GI wire/6mm MS rods of require sizes to maintain proper level etc. The aluminium framework is supported on side wall with the use of aluminium L-section of size 1"x1"(25x25mm) angles etc. complete as specified by manufacturer & drawing and directed by Engr-in- Charge.

S&F stainless steel decorative curtain rod of 25mm bore complete all as specified and directed.

S&F finial fancy type for curtain rod in pair etc complete all as specified and as directed.

S&F bracket for curtain rod in pair etc complete all as specified and as directed.

S&F designer type looking mirror of seleceted quality thickness not less than 6mm and of size 12 sqft to 24sqft fixed to wall with wooden plug with CP brass screw and cup washer complete all as specified and as directed.

S&F jet spray with 01 mtr PVC tube (Stainless steel) complete all as specified and directed.

S&F two way angle cock 15mm bore cast copper fancy CP alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F CP central basin mixer with U shaped round casted sprout with 450mm long baried houses complete all as specified and directed.

M&L for 18mm pre laminated plain colour WPC sheet of density 650 Kg/Cum for cabinet of wash hand basin, shelf partition wall etc including necessary hinges, handles, legs, closer magnet fixing with adhesive/ screws complete all as specified and as directed.

S&F designer table top vitreous china wash hand basin white/ coloured, size 610 x560mm including CP waste coupling but excluding taps, waste chain & plug complete all as specified and as directed.

S&F western floor mounted one piece water closet ceramic western toilet/commode/European commode square with soft close seat cover white including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe etc complete all as specified and as directed.

S&F bottle trap of having min water seal of 25mm (Minimum weight 32mm-260gms/40mm-270gms) complete all as specified and directed.

S&F 0.63 mm thick stainless steel plate rack of overall size 24"x36"x10" of standard quality and shape complete all as specified and directed.

M&L for XLPE insulated GI wire/Strip armoured Electric power cable (Heavy duty) with stranded Aluminium conductor 1100 Volts grade, cross sectional area 10Sqmm 2 core laid in trench/pole/on wall completer all as specified and directed.

Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc . Removing m,aterials to store for keeping in safe custody or for taking credit ( credit a for above items should be made as per condition seperately ) and making good distrubed surfaces of walls, floors etc.

Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface all as specified and directed at site.

Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed.

M&L for point wiring with 1.5 Sq mm single core PVC insulated unsheathed copper FRLSH multi stranded conductor cable in and including Concealed PVC conduit of size 20/25mm ISI marked inclusive of tees ,bend ,elbows etc upto and including sunk in Anodized pressed steel box for housing switch socket etc with white laminated 3 mm thick sheet cover ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sq mm FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal incl cutting, chasses and making good disturbed surface to match with existing finish with plaster for complete all as specified and directed.

One light point controlled by one, one way switch 5 Amps

One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

Description all as per item No 152.00 here in before but using 2.5 sq mm single core copper conductor cable of multistranded FRLSH PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 1.5 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common earth dolly.

Supply and fixing switch piano flush button single pole one way 5 amps, AC 240 Volts complete all as specified and directed.

Supply and fixing switch piano flush button single pole one way 15 Amps AC 240 volt complete all as specified and directed.

Supply and fixing socket outlet flush type 5 Amps, 5 pin, AC 240 Volts complete all as specified and directed.

Supply and fixing socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 Amps, AC 240 volts complete all as specified and directed.

S & F for Ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete all as specified

S & F call bell ding dong type, AC, 230 Volts complete all as specified

S&F Modular switch 1 way 6A, 1 module complete all as per specified and directed.

S&F Modular switch 1 way 16A, 1 module complete all as per specified and directed.

S&F Socket, 6A - 2/3 pin combined 2 module, complete all as per specified and directed.

S&F Socket 6A/16A - 2/3 pin combined 2 module, complete all as per specified and directed.

S&F Fan step regulator, 120W - 2 module complete all as per specified and directed.

S&F Modular bell push 6A, 1 Module complete all as per specified and directed.

S&F White cover plate with frame, 1 module complete all as per specified and directed.

S&F White cover plate with frame, 2 module complete all as per specified and directed.

S&F White cover plate with frame, 3 module complete all as per specified and directed.

S&F White cover plate with frame, 6 module complete all as per specified and directed.

S&F modular metal flush box 1/2 module complete all as specified and directed.

S&F modular metal flush box 3 module complete all as specified and directed.

S&F modular metal flush box 6 module complete all as specified and directed.

Supply & fixing 2 Module socket with sutter 25Amps 240 Volts including Moduler Metal flush box and cover Plate complete all as specified and directed.

Supply & fixing 2 Module starter switch 25 Amps 240 Volts including Moduler Metal flush box and cover Plate complete all as specified and directed.

S & F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

Supply and fixing double door SPN DBs 4 way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral as per existing finishing complete all as specified and directed.

S & F for MCB Single pole and neutral rated capacity 40-63 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

Supply and fixing LED tube light batten box type made of CRCA sheet with decorative end caps suitable with ultra bridght glass LED tube light 1x 18/20 watt T8 type single side connection complete with both end bi-pin holder and all accessories internally prewired and fixed to wall/ceiling incl fittings accessories and connecting up with twin core flexible copper conductor cable suitable size all as specified.

S & F for wall mounted LED tube light fitting 10 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etccomplete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed.

Supply and fixing Wall light fixture lantern made up of metal with chrome finish and white colour diffuser complete with LED 9 watt lamp B-22 base including all necessary accessories and connection complete all as specified and directed.

S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source (100 lm/watt) with LDR sensor for automatic ON/OFF operation and electronic driver of capacity 25 watts with pre wired and necessary mounting arrangements and provision of 1.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as specified and directed.

Supply and fixing LED bulk head 10 watt fittings environmental friendly ultra modern energy saving surface mounted decorataive bulk head fitting with driver and prewired and necessary electric connection with PVC insulated twin twisted flexible copper wire of size 0.75 Sqmm complete all as specified and directed.

Taking down ceiling fan/ exhaust fan of any sweep, keeping with safe custody and refixing the same with replacement of unsv 3 core PVC insulated PVC sheated 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal over hauling the fan complete all as specified and directed.

S & F for energy efficient exhaust fan of 300 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed.

S & F for energy efficient exhaust fan of 250 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. (Note : Cost of suitable opening wall for fixing exhaust fan is deemed to be included in overall rate quoted).

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm cable,one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit.

M & L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia. medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate no 3 of SSR part I including excavation and earthwork in any type of soil/strata and testing on completion. Note :- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted.

Taking down geyser of any capacity keeping with safe custody and refixing the same at the requisite site complete all as specified and directed

(Note : The Scope of Work contained in 'Sch of Credit' amounting to Rs. 59,589.00 (refer Tender Srl Page No 33). The Quoted sum shall be arrived at after deducting the amount of “Sch of Credit” from the total amount of the ‘BoQ’

M/S P. RAI CHOUDHURY AND CO. (BID ID -3401719)

V N ENTERPRISE (BID ID -3399989)

SUJATA TRADERS (BID ID -3401879)

M/S GURUNG CONSTRUCTION (BID ID -3400973)

MILAN GHOSH (BID ID -3401208)

PRADIP KUMAR BOSE (BID ID -3400959)

Amulya ky roy (BID ID -3401884)

REEJU BANIK (BID ID -3400121)