PROVN OF VEHICLE REPAIR SHED, SPECIAL REPAIR TO BUILDING NO P-11 COOK HOUSE AND CERTAIN OTHER SANCTIONED REVENUE WORKS AT KHUNMOH UNDER GE 861 EWS.

Amount

Surface dressing not exceeding 15 cm deep getting out in hard/dense soil, complete all as specified and directed.

Excavation in trenches n exc 1.50m wide and n exc 1.50m in depth for foundation etc or for shaft wells, cesspits manholes pier holes etc n. exc 10 sqm on plan and n. exc 1.5m in depth and getting out in hard/dense soil, complete all as specified and directed.

All as per srl item No-2 here in above, depth exc 1.50m but not exc 3.0m, complete all as specified and directed.

PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified.

RCC M-25 design mix using 20 mm graded aggregate in foundations, including rafts, footings, foundation beams, plinth beams, base for columns, etc basements slabs under rammed piles and mass concrete complete all as specified and directed.

RCC M-25 design mix using 20 mm graded aggregate in Column, pillars, piers, posts and struts complete all as specified and directed.

RCC M-25 design mix using 20 mm graded aggregate as in Beams cantilevers, bressummers lintels over 1.5 m span complete all as specified and directed.

Form work to sides of concrete foundations, footings, bases of columns, raft beams sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter complete all as specified and directed.

Form work to sides and soffits of floor or roof beam haunching , lintels, cantilevers shelved including supports overhangs etc also splays between floors and beams, etc complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finish surface of concrete square, rectangular or polygonal complete all as specified and directed.

Brick work with sub class 'B' bricks, straight or curved on plan, to any radius, in half brick thick wall, using old size brick, built in cement mortar 1:6, complete all as specified and directed.

M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6 finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 10mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 finished the surface even and smooth without using extra cement, complete all as specified and directed.

Rolled mild steel in roof trusses (framed),trussed ,purlins,crane girders,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-290 (Gde-E-165), complete all as specified and directed.

Rolled mild steel in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment, etc., and similar small articles, conforming to Fe-290 (Gde-E-165), complete all as specified and directed.

Mild steel work in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc., wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and as directed

MS TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not les than 0.9 mm dia or securing with clips quality conforming to complete all as specified and directed.

MS TMT Bars of 5 mm dia and over up to 10 mm dia in stirrups, spacers and binders, cut to length bent to shape required including cranking, binding spirally for hooping for columns hooking ends and binding with and including MS wire annealed not less than 0.9 mm dia or securining with clip complete all as specified and directed.

Pre painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and directed.

0.63mm thick , Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 etc, fixed with 'L' or 'J' type or cranked hook bolts in roofs, walls etc. complete all as specified and directed.

Preparation of new galvanised steel surfaces of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer over a coating of mordant solution including washing the surfaces, complete all as specified., complete all as specified and directed

Hard core of broken stone or boulders of guage n. exc 63mm, deposited, spread and levelled in layers n. exc 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

M&L 100mm thick, PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of floors & paving etc by using plate type electric vibrator, complete all as specified and directed .

M&L 75mm thick, PCC 1:2:4 type B-2 (using 40 mm graded crushed stone aggregate) as in floor laid in alternate bays(size of each panel 1.20x1.20m) including spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green and joints filled with mastic filling, including necessary formwork, complete all as specified and directed.

Sand filling under floors or in foundation including watering and consolidation, complete all as specified and directed.

M&L Plain cement concrete M-10, 1:3:6, type C-2, using 40mm graded mechanically crushed stone aggregate, 50mm thick, as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified and directed. Note:- The unit rate include for use of form work (straight or curved).

M&L PCC 1:2:4 type B-2 (using 40mm graded stone aggregate) as in surface channel and drains, complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying three coats of white wash,complete all as specified and directed.

Preapration of new plasetered or unplastered surfaces of wall and applying two coats of cement base paint, complete all as specified and directed.

Returning filling in (soil) including spreading, levelling , watering and well ramming in layers n exc 25cm thick, complete all as specified and directed.

Removing of surplus soil to a distance n exc 50 mtr and depositing where directed at a level n exc 1.5 mtr above the starting point, complete all as specified and directed.

Taking down cement plaster on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors & pavings n.exc 15 cm thickness (below or above ground level), complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises,complete all as specified and directed

Demolition of cement reinforced concrete (reinforcement cut as required to facilitate demolition) in ground floors & pavings n.exc 15 cm thickness (below or above ground level), complete all as specified and directed

Demolition of brick work or stone / boulder masonry, built in cement mortar, including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles etc, complete all as specified and directed

Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) exc 1.5 but n exc n.exc 4 Sqm each, complete as specified and directed

Taking down chowkats or frames including shutters (without taking off shutters from the frames) not exceeding 1.50 Sqm each, complete all as specified and directed

Dismantling wall and ceiling boards (fibre, Pulp, insulation etc) or insulation board/slabs/blankets, any thickness, including cover fillets etc, complete all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan, exceeding 6 m mean radius with old size bricks, built in cement mortar 1:4 complete all as specified and as directed.

RCC M-25 design mix using 20 mm graded aggregate as in slab supported on walls, beams and columns in floors, roofs landings balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Form work to sides and soffits of suspended slab such as roof slab, floor slab, shelves and similar works n. exc. 200 mms thick (Horizontal or sloping), finishing rought the concrete surfaces, complete all as specified and directed.

M&L for 10mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:3 as in roof slab, finished the surface even and smooth without using extra cement, complete all as specified and directed.

2nd class soft wood, plain, solid, straight chowkats and frames, wrought, framed, worught, framed rebated on the solid, rounded of chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

35 mm thick, 2nd class hard wood factory made, plain framed, panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneers on both faces. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified and directed.

35mm thick second class hard wood, glazed and skeleton shutters, divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and as directed

Anodised aluminium powder coated (thickness of powder coating 50 micron) frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Aluminium anodised powder coated (thickness of powder coating 50 micron) door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc, complete all as specified and as directed

Aluminium anodised powder coated window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc, complete all as specified and directed.

5.50mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares exc 0.50 Sqm in each pane, complete all as specified and directed.

12mm thick prelaminated particle board, interior grade prelaminated both sides with decorative choice laminations, fixed with screws to timber frame work, complete all as specified and directed.

S&F in repair brass 4 Levers Mortice lock, vertical type size 100 mm, complete all as specified and directed.

300mm size aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed.

Steel ventilator with top hung shutter incl hinges, steel peg stay, including one shop coat of red oxide primer, complete all as specified and directed, complete all as specified and directed.

200mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

150mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

150mm long, extruded aluminium alloy handles, fabricated type, anodised, all as specified and directed.

100 mm long, mild steel cold rolled Butt hinges, medium weight, complete all as specified and directed.

300mm long brass ordinary rat tail rod pattern, springs including roller and roller plate fixed to wooden chowkhat, complete all as specified and directed.

150mm long, floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

3mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, including hacking out old glass panes, complete all as specified and directed.

S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples,complete all as specified and directed

25 mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded crused stone aggregate) as in floors to recieve floor finishes, complete all as specified.

Vitrified tiles 10 mm thick, dark shade (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as spcified and directed.

Dismantling water storage tanks of any description, exceeding 250 litres but not exceeding 500 litres and removing from site, complete all as specified and directed.

S&F for Rotational moulded polythylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20 mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, complete all as specified and directed.

25mm thick Granite (of any type) work (table rubbed and polished and moulding of outer edges) in steps, jambs and pillars, window cills, cooking platforms and the like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with and including 15mm thick screed bed in CM 1:4, complete all as specified and directed.

S&F in repairs 15mm bore bib tap, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,complete all as specified and directed

S&F in repairs 15mm bore stop valves, fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed

Taking up or down 15mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Steel water tubing, 15 mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting, chases, pinning for concealed work etc and making good disturbed surfaces in CM 1:3, complete all as specified and directed.

Steel water tubing, 20 mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting, chases, pinning for concealed work etc and making good disturbed surfaces in CM 1:3, complete all as specified and directed.

S&F in repair PVC (SWR) pipes 110mm bore dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors etc, complete all as specified and directed.

S&F PVC (SWR) bends 110mm bore dia complete all as specified and directed.

Supply, fixing, jointing and testing, ISI Marked, of approved quality, gun metal globe/gate valve 20mm dia with iron wheel head, both ends screwed for iron pipe including taking down of old one complete all as specified and directed for following bore of pipes.

S&F in repair 2nd Class soft wood, weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps, complete all as specified.

Dismantling plain or corrugated steel sheeting , any gauge and thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed

0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap with zinc coating of 275, fixed with 'L' or 'J' type or cranked hook bolts in roofs, walls etc. complete all as specified and directed.

Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, conforming to Fe-290 (Gde-E-165), complete all as specified and directed.

M&L preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint over a coat of alkali-resistant priming paint, complete all as specified and directed

M&L preparation of new plastered or unplastered surfaces of walls and applying 3mm thick wall care putty, complete all as specified and directed

M&L preparation of new plasetered or unplastered surfaces of wall and applying two coats of oil bound distemper, complete all as specified and directed.

M&L preparation of new plastered or unplastered surfaces of ceiling or facia and applying three coats of white wash,complete all as specified and directed.

M&L preparation of old plastered/unplastered wall surfaces and applying two coats of cement base paint including complete removal of existing treatment, complete all as specifed and directed.

M&L complete removal of existing treatment of walls and preparing the surface to receive 3mm thick wall care putty and applying two coats of oil bound distemper, complete all as specified and directed.

M&L preparation of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

M&L preparation of new or previously untreated steel surface any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

M&L preparation of old painted wooden surcaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified.

Preparation of old decorated CGI sheet surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint in camouflage pattern, complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc., complete all as specified and directed.

S&F for anodised aluminium snap grid of size 605 x605 mm frame work for false ceiling including Hangers 6 mm dia MS rod (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long, complete all as specified and directed.

S&F for 10 mm thick PVC insulation panels with EPS stuck to 1 mm thick plain PVC sheet suitably placed in false celing grid made of aluminim GI/MS as per specification and drawing complete all as specified and directed.

M&L 75mm thick, PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of floor, complete all as specified.

M&L chequered cement concrete tiles of size 300 x 300 x 25 mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry, laid in floors, over and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

S&F solid PVC Wall panelling decorative type consisting of 5mm thick plain colour PVC prelaminated sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing, complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing, complete all as specified and directed

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil, complete all as specified and directed.

Excavation in trenches n exc 1.50m wide and n exc 1.50m in depth for foundation etc or for shaft wells, cesspits manholes pier holes etc n. exc 10 sqm on plan and n. exc 1.5m in depth and getting out in soft/loose soil, complete all as specified and directed.

M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick rendering on other than fair faces of brick work or concrete surfaces in CM 1:6 finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 5mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:3 finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L Plain cement concrete M-10, 1:3:6, type C-2, using 40mm graded mechanically crushed stone aggregate, 75mm thick, as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified and directed. Note:- The unit rate include for use of form work (straight or curved).

M & L for 40mm thick ,plain cement concrete, 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in floors finished even and smooth without using extra cement, complete all as specified and directed.

35 mm thick 2nd class hardwood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified.

Mild steel framed work such as grills, gratings etc with ends of bars shouldered or reveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar works, conforming to Fe-290, Gde E-165, complete all as specified and directed, complete all as specified and directed.

100mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

100mm long, extruded aluminium alloy handles, fabricated type, anodised, all as specified and directed.

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in hard/dense soil, complete all as specified and directed.

M & L for cement concrete in foundations 1:2:4, type-B2 (20mm graded stone aggregate), as in hardstanding laid in panels finished even and smooth without using extra cement, complete all as specified and directed.

M&L forming of 20mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound Grade 'A' in 150mm thick flooring, complete all as specified and directed.

M & L for forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade 'A', complete all as specified and directed.

Excavation in trenches n exc 1.50m wide and n exc 1.50m in depth for foundation etc or for shaft wells, cesspits manholes pier holes etc n. exc 10 sqm on plan and n. exc 1.5m in depth and getting out in any type of soil, complete all as specified and directed.

Hard core of broken stone or boulders of guage exc 63mm but n. exc 100mm, deposited, spread and levelled in layers n. exc 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

M&L for 25mm thick damp proof course to horizontal or vertical surfaces in cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) including necessary formwork, complete all as specified and directed.

M &L rendering 15mm thick on brick or concrete surfaces in CM 1:4 finished even and smooth without using extra cement including mixing of water proofing compound in the proportion as mentioned in manufacture's instructions complete all as specified. Note: Water proofing compound shall be measured and paid for separately.

Supply only integral water proofing compound of approved quality, complete all as specified and directed

Glazed ceramic coloured tiles 350x 250x7mm/450x350x7mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed.

Factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing shown in SSR Part-II, complete all as specified and directed

Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and joinned together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified and directed.

4 mm thick figured glass pin head type and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane, complete all as specified and directed.

S&F 10 litre capacity PVC valveless, low level, synphonic action type, flushing cistern, with inlet, ball valve, float valve, handle including brackets, complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of length 600mm, complete all as specified and directed.

S&F grating square 150mm size of PTMT (minimum weight 100grams), complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors etc, complete all as specified and directed.

S&F PVC (SWR) pipes 75mm bore dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors etc, complete all as specified and directed.

S&F PVC (SWR) pipes 75mm bore dia, single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and directed.

S&F PVC (SWR) bends 110mm bore dia complete all as specified and directed.

S&F PVC (SWR) bends 75mm bore dia complete all as specified and directed.

PVC (SWR) vent cowl for 75mm bore pipe and fixed, complete all as specified and directed.

PVC (SWR) 75mm bore, floor trap with grating including jointing with cement concrete 1:2:4 type B-1, complete all as specified and directed.

Supply, fixing, jointing and testing, ISI Marked, of approved quality, gun metal globe/gate valve 20mm dia with iron wheel head, both ends screwed for iron pipe, complete all as specified and directed for following bore of pipes.

M&L cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork, complete all as specified and directed.

15mm bore pillar tap,fancy type, cast copper alloy, with capstan head, chromium plated screwed down high pressure, with or without lettered hot/cold with long screwed shanks and fly nuts screwed for iron pipe, complete all as specified and directed.

S&F vitreous china squatting pan water closet, orissa pattern, size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) including cast iron 'P' or 'S' trap, jointing to flush pipe complete and making good to dismantled/damaged floor in cement concrete M-5 (1:5;10), type E-2 using 40mm graded crushed stone aggregate, complete all as specified and directed .

S&F vitreous china wash hand basin, white, size 630mmx450mm (flat back or angle back type) excluding taps, waste, chain and plug and pocelain stopper but including brackets and cutting for and pinning in ends of brackets or erecting stand, complete all as specified and directed.

S&F 15mm bore bib tap, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,complete all as specified and directed

S&F 15mm bore stop valves, fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed

MS TMT bars 6mm to 8mm dia and over cut to length,bent to shape required incl cranking bending and binding with and including mild steel wire(annealed) not less then .9mm dia, complete all as specified and directed.

Excavation over areas not exc 1.5m depth and getting out in soft/loose soil, complete all as specified and directed.

All as per srl item No-143 here in above, depth exc 1.50m but not exc 3.0m, complete all as specified and directed.

M&L 100mm thick, PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in flooring, complete all as specified and directed .

Brick work with sub class 'B' bricks in one brick thick honey-comb walling, built in cement mortar 1:6, complete all as specified and directed.

Brick work with sub class 'B' bricks, straight or curved on plan, to any radius, in half brick thick wall, built in cement mortar 1:4, complete all as specified and directed.

M&L cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork, complete all as specified and directed.

M&L precast reinforced cement concrete type 1: 2: 4, type-B1 (20 mm graded aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set and jointed in CM 1:4, complete all as specified and directed. (Note : Reinforcement shall be measured and paid separately)

Plain cement concrete bed 1:4:8 type D-2 (using 40mm graded crushed stone aggregates)to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150mm bore pipe, complete all as specified and directed.

Salt glazed stone ware drain pipe of 150mm bore (internal bore) garde 'A' laid in trenches and jointed, complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide to rough finished surfaces of concrete, complete all as specified and directed.

200mm long, mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed, complete all as specified and directed.

150mm long, mild steel pressed handles, oval type, stove enamelled black, all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including unscrewing from board fitting and fixture such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody for reuse if serviceable or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed

Point wiring concealed with 1.5 Sqmm PVC (FRLS) insulated unsheathed multi stranded copper conductor cable 1100 volts grade single core conforming to IS-694-1990 and including one run of continous earth wire to common earth and connected to earth with 1.5 Sqmm PVC (FRLS) insulated unsheathed multi stranded copper conductor cable draw in & incl PVC surface casing 'N' capping double lock type to be fixed with the help of rawal plugs & screws incl necessary fittings & fixture and to be turminated in sunk cast iron/pressed steel/PVC terminal boxes for mounting switches, sockets, regulators etc with 3 mm thick plastic laminated sheet cover of adequate size for one light point/fan point controlled by one switch and making good disturbed surfaces with CM (1:3) to match with the existing surface, complete all as specified and directed.

All as per srl item No-156 here in above but for one 3 pin 5A socket outlet independent controlled by one switch, complete all as specified and directed.

All as per srl item No-156 here in above but for one 5A socket outlet on the same board controlled by one switch, complete all as specified and directed.

All as per serial item No 156 here-in-before but for 3 pin 15 Amps socket outlet independent with 2.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 2.5 Sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green color) as earth lead, complete all as specified and directed.

Switch piano flush button types 5/6 Amp, single pole, one way complete all as specified and directed.

Switch socket combination 2 in 1, 5/6 pin, 5 and 15 Amp, flush type universal complete all as specified and directed.

Switch socket combination 2 in 1, outlet 5 pin, 5 Amp flush type, universal, complete all as specified and directed.

Ceiling rose 3 terminal bakelite 65mm x50mm surface type, PVC/Polycarbonate, isolated body, complete all as specified and directed.

S&F decorative ultra slim linear LED in replacement of 20 Watt , 4 ' long lighting fixture with extruded Al heat sink , environment friendly , energy efficient ready to use pack including LED tube complete with inbuilt electronic driver , PCB , connector block etc including connecting up with three core twisted flexible copper conductor cable with suitable size LED tube all as specified and directed. Make : Havells Cat Part No LHEXBLP7PN1W020 or Equivalent/C&S/Bajaj.

Lamp holder, PVC/ Polycarbonate type with back plate, straight/ angular, suitable for batten fittings, complete all as specified and directed.

S&F in repair, LED lamp 9W fixture with in built electronic driver complete with all accessories prewired and connecting electrically to ceiling rose using PVC FRLS insulated and overall sheathed cable, complete all as specified and directed . Make : Havells Cat Part No LHLDEUHEML8R009 or Equivalent/C&S/Bajaj

Supply & fixing MCB Distribution board , 240 volts single pole and neutral , double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 12 ways, IP-43 protection, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/distempering etc to match the existing surface, complete all as specified and directed.

Supply and fixing MCB SP, 6 to 32 Amps, 240 Volts 10 KA, 'C' series, fixed in repair and biconnect upper & lower terminals, integrated label holder to ensure circuit identification, complete all as specified and directed. Make : Havells Cat Part No DHMGCSNF006-032 or equivalent in C&S/Legrand/Siemens/Scheinder.

Supply and fixing MCB TPN, 40 Amps to 63 Amps, 240 volts 10kA , 'C' series, fixed in repair including providing thimble for outgoing cables and making connections complete all as specified & directed. Make : Havells Cat Part No DHMGCTNF040-063 or equivalent in C&S/Legrand/Siemens/Scheinder.

Taking down old unserviceable electric storage water heater any type/size, supply and installation of electric storage water heater (vertical type geysers), five star rating, 35 litres capacity, 240 Volts, AC Single phase capacity having stainless steel inner tank, including heavy duty pin type fasteners 4" long as per site requirement and making necessary inlet/outlet water connections and making good disturbed surface of walls to match with existing surface complete all as specified and directed.

Supply and fixing in repair energy efficient highly rated, heavy duty exhaust fan 600mm sweep with louvers, ISI marked, including necessary work in wall/sheet, including connection cable of suitable size, nut bolt and other fixing material complete all as specified and directed

Sub main wiring with two single core PVC insulated flexible copper conductor cable of size 6.0 sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 4.0 Sqmm as earth lead in & including concealed PVC casing capping medium grade 2mm thickness ISI marked or cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification incl taking down old unsv, complete all as specified and directed.

Supply laying connecting and testing in repair 1100 volt graded heavy duty XLPE cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanized steel strip or wire and overall PVC sheathed of size 25 Sqmm normal cross section 3.5 core including suitable size lugs laid in trenches fixed to pole or passing through pipes incl all necessary clamps nuts, bolts and washers and remove unsv cable complete all as specified and directed. Note- Earth work and protection work shall be measured and paid for separately under respective items of BOQ.

S&F 50mm dia bore galvanized iron tubing, light grade including all fitting for cable protection etc laid in floor, trenches or fixed to poles with clamps etc complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level. connecting to the GI wire 4 mm dia by means of bolls, nuts, check nuts and washers of galvanised iron and earth wire protected by provision of GI light grade pipe 15mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM weight not less than 4 Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and handle of 6mm dia MS bar made to shape, GI medium grade 20mm bore pipe for watering , perforated at bottom. 1.75 metre long placed on top edge of earth plate. charcoal and common salt filling with fixing arrangement, funnel wire mesh and earth work in soft soil returning filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate 3 of SSR-2009 Part-I and connecting to earth test point all as specified or indicated including testing on completion. NOTE :- (i) Item of earthing includes cost of 7.5 m long GI wire of size 4 mm dia with protection pipe of 15mm dia GI medium grade, any variation in length shall be adjusted through deviation order based on SSR rates enhanced by 25%. (ii) On testing after completion of earthing if the desired earth resistance is not obtained earthing will be re-done by the contractor at his own risk and cost.

S&F 20mm dia bore galvanized iron tubing, light grade including all fitting for cable protection etc laid in trenches, complete all as specified and directed.

Sand cushioning to underground cable as per clause No 19.75 of SSR Part-I laid with a layer of sand 8 cm before laying the cable and 15 cm after laying the cable. The top layer of 15cm shall be punned to 10 cm (total 23 cm) complete all as specified and directed.

Sub class ‘B’ brick old size protection cover laid dry flat transversally along the length of cable on cushioning with width equal to the length of brick complete all as specified and directed .

BASHIR AHMAD MIR

M/S Alam Construction

SAMEER CONSTRUCTIONS

M/S STARE BUILDERS

Javeed And Co