REPAIRS /MAINTENANCE OF CI/DI/GI/CPVC/PUMP MOTORS/BOREWELLS INCLUDING BREAKDOWN AND CONNECTED ITEMS UNDER GE BRICHGUNJ

Amount

Dismantling of 165 HP, 415 volt, 3 phase centrifugal motor pump set, removing electrical connections, dismantling of stator, rotor, pumpset separately including transporting to workshop for servicing/repairs and reassembling, transporting back, refixing the motor pumpset in position including making proper alignment and necessary electrical connections, testing etc. complete all as specified and as directed by Engr-in-Charge.

Note: (i) Rewinding of motor will be measured and paid separately. (ii) Labour for replacement of bearings deemed be included in quoted rates (iii) Bearings shall be measured and paid as supply only.

All as per item No 1 here in before, but pump set of capacity 75 HP, 415 volt, 3 phase complete all as specified and directed.

All as per item No 1 here in before, but pump set of capacity 50 HP, 415 volt, 3 phase complete all as specified and directed.

All as per item No 1 here in before, but pump set of capacity 38/40 HP, 415 volt, 3 phase complete all as specified and directed.

All as per item No 1 here in before, but pump set of capacity 25 HP, 415 volt, 3 phase complete all as specified and directed.

All as per item No 1 here in before, but pump set of capacity 20 HP, 415 volt, 3 phase complete all as specified and directed.

All as per item No 1 here in before, but pump set of capacity 15 HP, 415 volt, 3 phase complete all as specified and directed.

All as per item No 1 here in before, but pump set of capacity 7.5 HP, 415 volt, 3 phase complete all as specified and directed.

All as per item No 1 here in before, but pump set of capacity 5 HP, 415 volt, 3 phase complete all as specified and directed.

All as per item No 1 here in before, but pump set of capacity 3 HP, 415 volt, 3 phase complete all as specified and directed.

All as per item No 1 here in before, but pump set of capacity 3 HP, single phase complete all as specified and directed.

All as per item No 1 here in before, but pump set of capacity 2 HP, single phase complete all as specified and directed.

All as per item No 1 here in before, but pump set of capacity 1.5 HP, single phase complete all as specified and directed.

All as per item No 1 here in before, but pump set of capacity 1 HP, single phase complete all as specified and directed.

Supply and fixing in repairs impeller suitable for 165 HP capacity pump, 415 volt, 3 phase motor pump set (as per existing size) complete all as specified and as directed by Engr-in-Charge. Make : NBC / SKF

Supply and fixing in repairs impeller suitable for 7.5 HP capacity pump, 415 volt, 3 phase motor pump set (as per existing size) complete all as specified and as directed by Engr-in-Charge. Make : NBC / SKF

Supply and fixing in repairs impeller suitable for 5 HP capacity pump, three phase motor pump set (as per existing size) complete all as specified and as directed by Engr-in-Charge. Make : NBC / SKF

Supply and fixing in repairs impeller suitable for 3 HP capacity pump, single phase motor pump set (as per existing size) complete all as specified and as directed by Engr-in-Charge. Make : NBC / SKF

Supply and fixing in repairs impeller suitable for 2 HP capacity pump, single phase motor pump set (as per existing size) complete all as specified and as directed by Engr-in-Charge. Make : NBC / SKF

Supply and fixing in repairs impeller suitable for 1.5 HP capacity pump, single phase motor pump set (as per existing size) complete all as specified and as directed by Engr-in-Charge. Make : NBC / SKF

Supply and fixing in repairs impeller suitable for 1 HP capacity pump, single phase motor pump set (as per existing size) complete all as specified and as directed by Engr-in-Charge. Make : NBC / SKF

Supply only bearing suitable for 165 HP capacity pump, 415 volt, 3 phase motor pump set (as per existing size) complete all as specified and as directed by Engr-in-Charge. Make : NBC / SKF

Supply only bearing suitable for 75 HP capacity pump, 415 volt, 3 phase motor pump set (as per existing size) complete all as specified and as directed by Engr-in-Charge. Make : NBC / SKF

Supply only bearing suitable for 50 HP capacity pump, 415 volt, 3 phase motor pump set (as per existing size) complete all as specified and as directed by Engr-in-Charge. Make : NBC / SKF

Supply only bearing suitable for 25 HP capacity pump, 415 volt, 3 phase motor pump set (as per existing size) complete all as specified and as directed by Engr-in-Charge. Make : NBC / SKF

Supply only bearing suitable for 20 HP capacity pump, 415 volt, 3 phase motor pump set (as per existing size) complete all as specified and as directed by Engr-in-Charge. Make : NBC / SKF

Supply only bearing suitable for 7.5 HP capacity pump, 415 volt, 3 phase motor pump set (as per existing size) complete all as specified and as directed by Engr-in-Charge. Make : NBC / SKF

Supply only bearing suitable for 5 HP capacity pump, three phase motor pump set (as per existing size) complete all as specified and as directed by Engr-in-Charge. Make : NBC / SKF

Supply only bearing suitable for 3 HP capacity pump, single phase motor pump set (as per existing size) complete all as specified and as directed by Engr-in-Charge. Make : NBC / SKF

Supply only bearing suitable for 2 HP capacity pump, single phase motor pump set (as per existing size) complete all as specified and as directed by Engr-in-Charge. Make : NBC / SKF

Supply only bearing suitable for 1.5 HP capacity pump, single phase motor pump set (as per existing size) complete all as specified and as directed by Engr-in-Charge. Make : NBC / SKF

Supply only bearing suitable for 1 HP capacity pump, single phase motor pump set (as per existing size) complete all as specified and as directed by Engr-in-Charge. Make : NBC / SKF

Material and Labour for taking out old burnt copper winding of stator and rotor, cleaning the slots and re-winding of motor with suitable gauge super enamelled copper winding wire for 165 HP, 3 phase motor complete all as specified and as directed by Engr-in-Charge.

Material and Labour for taking out old burnt copper winding of stator and rotor, cleaning the slots and re-winding of motor with suitable gauge super enamelled copper winding wire for 75 HP, 3 phase motor complete all as specified and as directed by Engr-in-Charge.

Material and Labour for taking out old burnt copper winding of stator and rotor, cleaning the slots and re-winding of motor with suitable gauge super enamelled copper winding wire for 50 HP, 3 phase motor complete all as specified and as directed by Engr-in-Charge.

Material and Labour for taking out old burnt copper winding of stator and rotor, cleaning the slots and re-winding of motor with suitable gauge super enamelled copper winding wire for 40/38 HP, 3 phase motor complete all as specified and as directed by Engr-in-Charge.

Material and Labour for taking out old burnt copper winding of stator and rotor, cleaning the slots and re-winding of motor with suitable gauge super enamelled copper winding wire for 25 HP, 3 phase motor complete all as specified and as directed by Engr-in-Charge.

Material and Labour for taking out old burnt copper winding of stator and rotor, cleaning the slots and re-winding of motor with suitable gauge super enamelled copper winding wire for 20 HP, 3 phase motor complete all as specified and as directed by Engr-in-Charge.

Material and Labour for taking out old burnt copper winding of stator and rotor, cleaning the slots and re-winding of motor with suitable gauge super enamelled copper winding wire for 15 HP, 3 phase motor complete all as specified and as directed by Engr-in-Charge.

Material and Labour for taking out old burnt copper winding of stator and rotor, cleaning the slots and re-winding of motor with suitable gauge super enamelled copper winding wire for 7.5 HP, 3 phase motor complete all as specified and as directed by Engr-in-Charge.

Material and Labour for taking out old burnt copper winding of stator and rotor, cleaning the slots and re-winding of motor with suitable gauge super enamelled copper winding wire for 5 HP, 3 phase motor complete all as specified and as directed by Engr-in-Charge.

Material and Labour for taking out old burnt copper winding of stator and rotor, cleaning the slots and re-winding of motor with suitable gauge super enamelled copper winding wire for 3 HP, 3 phase motor complete all as specified and as directed by Engr-in-Charge.

Material and Labour for taking out old burnt copper winding of stator and rotor, cleaning the slots and re-winding of motor with suitable gauge super enamelled copper winding wire for 3 HP, single phase motor complete all as specified and as directed by Engr-in-Charge.

Material and Labour for taking out old burnt copper winding of stator and rotor, cleaning the slots and re-winding of motor with suitable gauge super enamelled copper winding wire for 2 HP, single phase motor complete all as specified and as directed by Engr-in-Charge.

Material and Labour for taking out old burnt copper winding of stator and rotor, cleaning the slots and re-winding of motor with suitable gauge super enamelled copper winding wire for 1.5 HP, single phase motor complete all as specified and as directed by Engr-in-Charge.

Material and Labour for taking out old burnt copper winding of stator and rotor, cleaning the slots and re-winding of motor with suitable gauge super enamelled copper winding wire for 1 HP, single phase motor complete all as specified and as directed by Engr-in-Charge.

Supply and fix in repairs pump shaft coupling suitable for 165 HP pump (as per existing) complete all as specified and as directed.

Supply and fix in repairs pump shaft coupling suitable for 75 HP pump (as per existing) complete all as specified and as directed.

Supply and fix in repairs pump shaft coupling suitable for 50 HP pump (as per existing) complete all as specified and as directed.

Supply and fix in repairs pump shaft coupling suitable for 40/38 HP pump (as per existing) complete all as specified and as directed.

Supply and fix in repairs pump shaft coupling suitable for 25 HP pump (as per existing) complete all as specified and as directed.

Supply and fix in repairs pump shaft coupling suitable for 20 HP pump (as per existing) complete all as specified and as directed.

Supply and fix in repairs pump shaft coupling suitable for 15 HP pump (as per existing) complete all as specified and as directed.

Supply and fix in repairs pump shaft coupling suitable for 7.5 HP pump (as per existing) complete all as specified and as directed.

Supply and fix in repairs pump shaft coupling suitable for 5 HP pump (as per existing) complete all as specified and as directed.

Supply and fix in repairs pump shaft coupling suitable for 3 HP pump (as per existing) complete all as specified and as directed.

Supply and fix in repairs pump shaft coupling suitable for 2 HP pump (as per existing) complete all as specified and as directed.

Supply and fix in repairs pump shaft coupling suitable for 1.5 HP pump (as per existing) complete all as specified and as directed.

Supply and fix in repairs pump shaft coupling suitable for 1 HP pump (as per existing) complete all as specified and as directed.

Supply and fix in repairs gland packing suitable for 165 HP pump complete all as specified and as directed.

Supply and fix in repairs gland packing suitable for 75 HP pump complete all as specified and as directed.

Supply and fix in repairs gland packing suitable for 50 HP pump complete all as specified and as directed.

Supply and fix in repairs gland packing suitable for 40/38 HP pump complete all as specified and as directed.

Supply and fix in repairs gland packing suitable for 25 HP pump complete all as specified and as directed.

Supply and fix in repairs gland packing suitable for 15 HP pump complete all as specified and as directed.

Supply and fix in repairs gland packing suitable for 7.5 HP pump complete all as specified and as directed.

Lifting old unserviceable submersible pump set of 3.0/5.0/7.5 HP capacity along with column pipe, electrical connection cables and steel wire rope from bore well of 80 m avg depth, without damaging the bore well including all necessary labour and T&P as required complete all as specified and as directed.

Lowering serviceable submersible pump set and anchoring in to the bore well with clamps including electric connections and testing, commissioning, without damaging the bore well including all material, labour and T&P complete all as specified and as directed by Engineer - in - Charge.

Material and Labour for dismantling submersible pump set of capacity 7.5 HP for replacement of unserviceable parts, transporting to workshop and bringing back and reassembling the same after repairs complete all as specified and as directed by Engr-in-Charge.

Note: (i) Spare parts will be measured and paid as supply only. (ii) Rewinding will be measured and paid separately.

All as per item No. 69 here in before, but 5.0 HP complete all as specified and as directed by Engr-in-Charge.

All as per item No. 69 here in before, but 3.0 HP complete all as specified and as directed by Engr-in-Charge.

Supply only bearings suitable for 7.5 HP submersible pump set (as per existing) Make : NBC / SKF

Supply only bearings suitable for 5.0 HP submersible pump set.(as per sample) Make : NBC / SKF

Supply only bearings suitable for 3.0 HP submersible pump set.(as per sample) Make : NBC / SKF

Supply and fix in repairs column pipe with heavy duty GI tubing 40mm dia bore, each 3m length threaded both ends and with coupling (socket) suitable for above column pipe, in bore well complete all as specified and as directed by Engr-in-Charge. Make : Bansal/Tata/Jindal

Supply and fix in repairs column pipe with heavy duty GI tubing 50mm dia bore, each 3m length threaded both ends and with coupling (socket) suitable for above column pipe, in bore well complete all as specified and as directed by Engr-in-Charge. Make : Bansal/Tata/Jindal

Material and Labour for dismantling the submersible motor and removing burnt windings, rewinding with approved quality super enamel insulated copper winding wire, replacing old insulating materials for 3 phase 5 HP submersible motor and reassembling the motor, fixing and connecting as directed by Engr-in-Charge.

Material and Labour for dismantling the submersible motor and removing burnt windings, rewinding with approved quality super enamel insulated copper winding wire, replacing old insulating materials for 3 phase 7.5 HP submersible motor and reassembling the motor, fixing and connecting complete all as specified and as directed by Engr-in-Charge

Material and Labour for dismantling the submersible motor and removing burnt windings, rewinding with approved quality super enamel insulated copper winding wire, replacing old insulating materials for 3 phase 3 HP submersible motor and reassembling the motor, fixing and connecting complete all as specified and as directed by Engr-in-Charge

Material and Labour for development of bore well/tube well with compressed air to provide adequate pressure in the bore well for flushing out / removal of muddy water and other materials like sand, lay deposits and rock cuttings accumulated in bore well etc., flushing shall be carried out for minimum 4 hours to achieve better results complete all as specified and as directed by Engr-in-Charge.

Material and Labour for conducting yield test of the bore well by continuously pumping for 8 hours to determine safe pumping yield complete all as specified and as directed by Engr-in-Charge.

Collecting water samples from bore well in plastic cans, transporting to Govt approved lab at Port Blair, testing for organoleptic and physical parameters as per table 1 and General parameter concerning substances undesirable in excessive amount as per table 2 of IS:10500 (specification for drinking water) and submitting test reports complete all as specified and as directed by Engr-in-Charge

Supply and fix PVC insulated, submersible multistranded flat, copper conductor cable of size 3 core, 2.5 sqmm including necessary connections including taking out old unserviceable submersible cable complete all as specified and as directed by Engr-in-Charge.

Supply and fix in repairs contactor for FASD starter 80A OF type MNX 80 complete all as specified and as directed by Engr-in-Charge. Make: L&T cat No CS97077 or equivalent in Legrand/C&S as approved by GE

Supply and fix in repairs timer for FASD starter 240/360/415V, 50 HZ for 12-120 sec complete all as specified and as directed by Engr-in-Charge. Make: L&T cat No ST80329OOOO or equivalent in Legrand/C&S as approved by GE

Supply and fix in repairs relay for FASD starter MN 12 CT operating range 90-150A complete all as specified and as directed by Engr-in-Charge. Make : L&T cat No SS94138OOMO or equivalent in Legrand/C&S as approved by GE

Taking out old unserviceable DOL motor starter from panel after disconnecting all electrical connections, Material and Labour for supply, install testing and commissioning of DOL starter for centrifugal motors, 6-10 Amps, 415 Volts in sheet steel enclosure including O/C relay, contactors complete all as specified and as directed by Engr-in-Charge. Make: L & T Model No. MKI DOL or equivalent as approved by GE

All as per item No 87 here in before, but 20-32 Amp for 7.5 HP, 3 phase motor complete all as specified and as directed by Engr-in-Charge. Make : L&T, Model No MK2 DOL or equivalent as approved by GE

Material and Labour for supply, install, connecting, testing and commissioning of fully automatic star-Delta motor controller suitable for submersible pump sets of capacity up to 5/7.5 HP in sheet-steel enclosure, 415 volt, 3 phase, 50 Hz including Auto ON, indications of supply ON/OFF and pump ON/OFF, recording of real time voltage and current of pump with digital meter, single phase protection relay, phase reversal protection, phase unbalance protection etc complete including taking out existing old submersible motor controller from its location by disconnecting all cable connections complete all as specified and as directed. Make : L&T - MU-G15 CS94091 or equivalent as approved by GE

Supply and fixing in repairs new rubber coupling bush with bolt and nuts and aligning the pumpset properly for 165 HP pumpset complete all as specified and as directed.

Supply and fixing in repairs new rubber coupling bush with bolt and nuts and aligning the pumpset properly for 75 HP pumpset complete all as specified and as directed.

Supply and fixing in repairs new rubber coupling bush with bolt and nuts and aligning the pumpset properly for 50 HP pumpset complete all as specified and as directed.

Supply and fixing in repairs new rubber coupling bush with bolt and nuts and aligning the pumpset properly for 40/38 HP pumpset complete all as specified and as directed.

Supply and fixing in repairs new rubber coupling bush with bolt and nuts and aligning the pumpset properly for 25 HP pumpset complete all as specified and as directed.

Supply and fixing in repairs new rubber coupling bush with bolt and nuts and aligning the pumpset properly for 20 HP pumpset complete all as specified and as directed.

Material and labour for new CI foot valve, 150 mm dia, lowering to sump and fixing to its original position including dismantling and taking up old unserviceable CI foot valve from U/G sump complete all as directed and specified by Engr-in-Charge.

All as per item No 96 here in before, but 100mm dia complete all as specified and as directed by Engr-in-Charge

All as per item No 96 here in before, but 200mm dia complete all as specified and as directed by Engr-in-Charge

Material and labour for rubber shaft coupling with four Nos of 10mm thickness, 40mm width and not exceeding 15 cm length each including drilling and threading metal flange complete with new gasket, bolts, nuts, washers etc. including taking out old unserviceable rubber shaft, complete all as specified and as directed by Engr-in-Charge.

Supply and fix Single Phase Preventer relay (SPP) Suitable for submersible pump including taking out old unserviceable preventer, complete all as specified and as directed by Engr-in-Charge. Make: L&T - ST92166OOOO or equivalent as approved by GE

Taking down diesel driven engine pump of capacity upto 10 BHP from base, transporting to workshop for servicing, replacing fuel & oil filter, air cleaner, engine oil pipe, copper lead wire of suitable size including clamps, nuts and bolts and applying one coat of synthetic enamel paint and transporting back to site and refixing on the existing base including testing and commissioning complete all as directed by Engr-in-Charge.

Draining out old engine oil from engine and supply and filling engine oil to required level for 10 BHP diesel driven engine pump complete all as specified and as directed by Engr-in-Charge

Material and Labour for replacement of power contactor assembly suitable for starter ML-3 type, 3 phase, 415 V AC, 50 HZ complete all as specified and as directed by Engr-in-Charge. Make : L&T -SS90721 or equivalent as approved by GE

Material and Labour for replacement of power contactor assembly suitable for starter ML-4 type, 3 phase, 415 V AC, 50 HZ complete all as specified and as directed by Engr-in-Charge. Make : L&T - SS90910 or equivalent as approved by GE

Supply and fix in repairs electronic over load relay suitable for 50 HP starter, 3 phase, 415 V AC, 50 HZ complete all as specified and as directed by Engr-in-Charge. Make : L&T - MPR305BE320 or equivalent as approved by GE

Supply and fix in repairs thermal over load relay suitable 25 HP pump sets starter, 3 phase, 415 V AC, 50 HZ, 20-32A complete all as specified and as directed by Engr-in-Charge. Make : L&T - CS96366OOEO or equivalent as approved by GE

Supply and fix in replacement of mono block self-priming pump motor of capacity 1 HP 180-240 volts, Single phase, 50 Hz, head range 10-30 Mtr, discharge range 16-70 LPM of max suction 8M, class B insulation, including advanced features of preventing motor from burning against over current, due to low voltage and low maintenance motor with IP-44 protection and CPVC pipe connections complete all as specified and as directed. Make: kirlosker brothers limited model No. Eterna HL -32MS or equivalent as approved by GE

Supply and fix VAF & PF meter digital type square dial of size 96 mmX96 mm for LT Panel/ APFC Panel and taking down of existing unserviceable item complete all as specified and as directed by Engineer -in -Charge. Make : L&T - WL411011OOOO or equivalent as approved by GE

Supply and fix LED Type indicator lamp assembly suitable for LT panels including taking down of existing unserviceable item complete all as specified and as directed by Engineer -in -Charge.

Supply and replacement of nylon rope of size in 20 mm dia (as per sample) complete all as specified and as directed by Engr-in-Charge

Material and Labour for applying two coats of synthetic enamel paint to LT panel boards of any type / capacity three phase 415 Volt, 50 Hz rating, with smoke grey colour/shade including preparation of old painted surfaces complete all as specified and as directed by Engr-in-Charge

Material and Labour cement concrete 1:3:6, type C-1 (using 20mm graded aggregate) as in coping, including necessary form work complete all as specified and as directed by Engr-in-Charge.

Supply and fix in repairs rubber gasket joint suitable for spigot & socket pipes and fittings, of size 80mm dia complete all as specified and as directed by Engr-in-Charge

Supply and fix in repairs rubber gasket joint suitable for spigot & socket pipes and fittings, of size 100mm dia complete all as specified and as directed by Engr-in-Charge

Material and Labour for lead wool joints suitable for spigot & socket pipes and fittings of size 80mm dia complete all as specified and as directed by Engr-in-Charge

Supply and fix 20mm nominal dia, CPVC pipes of pressure rating 10Kgf/sqcm class 2 (SDR 13.5) with fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc., as required at site on walls, ceilings, floors and in trenches including taking up or down old unserviceable CPVC pipes complete all as specified and directed.

Supply and fix 25mm nominal dia CPVC pipes of pressure rating 10Kgf/sqcm class 2 (SDR 13.5) with fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc., as required at site on walls, ceilings, floors and in trenches including taking down old unserviceable CPVC pipes complete all as specified and directed.

Supply and fix 40mm nominal dia CPVC pipes of pressure rating 10Kgf/sqcm class 2 (SDR 13.5) with fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc., as required at site on walls, ceilings, floors and in trenches including taking down old unserviceable CPVC pipes complete all as specified and directed.

Supply and fix in 50mm nominal dia CPVC pipes of pressure rating 10Kgf/sqcm class 2 (SDR 13.5) with fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc., as required at site on walls, ceilings, floors and in trenches including taking down old unserviceable CPVC pipes complete all as specified and directed.

Supply and fix in repairs 20mm dia ball valves, union type, high pressure, CPVC polythene gate and flynut complete all as specified and as directed.

Supply and fix in repairs 25mm dia ball valves, union type, high pressure, CPVC polythene gate and flynut complete all as specified and as directed.

Supply and fix in repairs 40mm dia ball valves, union type, high pressure, CPVC polythene gate and flynut complete all as specified and as directed.

Supply and fix in repairs 50mm dia ball valves, union type, high pressure, CPVC polythene gate and flynut complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep and getting out for taking out or laying of pipes/cable of any size in soft/ loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick in any type soil complete all as specified and as directed.

Removing excavated material (soil) not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Material and Labour for Pre-cast cement concrete block masonry with solid blocks, exceeding 10 CM in width, in cement concrete 1:3:6 type C1, using 20 mm graded aggregate set in CM 1:4 including taking down of broken existing item complete all as specified and directed.

Material and Labour for rendering 10 mm thick in cement mortar 1:4, on fair faces of concrete surfaces, finishing the surface even and smooth without using extra cement complete all as specified and directed.

Material and Labour for rendering 10 mm thick in cement mortar 1:6, on fair faces of concrete surfaces, finishing the surface even and smooth without using extra cement complete all as specified and directed.

Material and Labour for cement concrete 1:2:4, type B1, using 20mm graded stone aggregates as in coping including formwork finished using extra cement all as specified and as directed.

Material and Labour in repairs to pipe line, after taking up CI / DI water mains of 200mm bore including all fittings with spigot and socket ends and lead joints, including burning out joints and recovering lead complete and relaying, jointing, testing after repairs complete all as specified and as directed by Engr-in-Charge.

Excavation and earth work in mud/hard soil etc by using machinary/labour to any length to attend pipe line breakdown as per site conditions and forming bund with excavated soil to avoid water entering into the working area including pumping/bailing out water by using portable diesel engine driven pump set including the following complete all as specified and as directed :- (i) Cutting of unserviceable CI/DI pipe of size 300/400/500 mm dia after thorough inspection for the damage including bailing out water using portable pump set. (ii) Taking out damaged/ unserviceable pipe after removing from rubber tyton joint/burning out lead joints at both ends & replacing with new 300/400/500 mm dia DI pipe line in lieu of existing in to trenches using machinary / labour as required complete all as directed by Engineer-in-Charge. (iii) Transportation of DI pipe / fittings of size 300/400/500 mm dia from Prothrapur Pump house to work site and cutting the pipe to required length to suit site conditions. (iv) Jointing pipe by using rubber tyton rings 300/400/500mm dia to the corresponding socket and spigot ends of the existing pipe line after aligning the pipe line as per site condition, inserting the CI collar of size 300/400/500 mm dia, complete all as directed by Engineer-in-Charge. (v) Making run lead joints in CI collar 300/400/500 mm dia or in any other specials of any size and any type, caulking of joints and testing for leakages if any, complete all as specified and as directed by Engineer-in-Charge.

(vi) Returning filling in including removal of surplus mud/excavated materials with the help of earthmoving machinery (Hitachi), complete all as specified and as directed by Engineer-in-Charge. Note :- (a) DI pipe and fittings of size 300/400/500 mm dia shall be measured and paid separately under relevant item here in after as supply only (b) Cost of tools & plants as required for work & transportation is deemed to be included in the unit rate quoted. (c) The Contractor shall take due care while executing the work (i.e., especially taking out old existing pipe line and laying new pipe line). Any damage to the existing services (i.e electrical cable,telephone cable,water supply pipe line and road etc) during execution of work shall be repaired immediatly and cost of the same is deemed to be included in the quoted rates)

Supply only 300 mm bore ductile iron pressure pipes, class "K-9" with socket and spigot ends conforming to IS - 8329 in standard lengths suitable for push-on rubber gasket jointing with inside mortar lining and black bitumen external coating complete all as specified and as directed. Make: Electro steel / Tata / Jindal/Rashmi.

Supply only 400 mm bore ductile iron pressure pipes, class "K-9" with socket and spigot ends conforming to IS - 8329 in standard lengths suitable for push-on rubber gasket jointing with inside mortar lining and black bitumen external coating complete all as specified and as directed. Make: Electro steel / Tata / Jindal/Rashmi.

Supply only 500 mm bore ductile iron pressure pipes, class "K-9" with socket and spigot ends conforming to IS - 8329 in standard lengths suitable for push-on rubber gasket jointing with inside mortar lining and black bitumen external coating complete all as specified and as directed. Make: Electro steel / Tata / Jindal/Rashmi.

Material and Labour for caulking of lead joints with lead wool at places of leakage from the pipe and arresting leakages for 500mm bore of pipe, complete all as specified and as directed by Engr-in-Charge

Material and Labour for caulking of lead joints with lead wool at places of leakage from the pipe and arresting leakages for 400mm bore of pipe, complete all as specified and as directed by Engr-in-Charge

Material and Labour for detecting leakage in cast iron pressure pipes/ HDPE of 200 mm bore in any location, any depth including necessary earthwork excavation and repairing and arresting leakage by providing jointing material (fusion/ mirror joints in case of HDPE pipes), flanged clamps, nuts, washers & bolts etc. complete all as specified and as directed.

Taking out sluice valve of 80mm bore, repairing and refixing the same after re-facing, grinding the valve check nuts, Spindle etc. including jointing materials complete all as specified and directed.

Taking out sluice valve of 100mm bore, repairing and refixing the same after re-facing, grinding the valve check nut, Spindle etc. including jointing materials complete all as specified and directed.

Taking out sluice valve of 200mm bore, repairing and refixing the same after re-facing, grinding the valve check nuts, Spindle etc. including jointing materials complete all as specified and directed.

Taking out sluice valve of 250mm bore, repairing and refixing the same after re-facing, grinding the valve check nuts, Spindle etc. including jointing materials complete all as specified and directed.

Taking out sluice valve of 300mm bore, repairing and refixing the same after re-facing, grinding the valve check nuts, Spindle etc. including jointing materials complete all as specified and directed.

Taking out sluice valve of 400mm bore, repairing and refixing the same after re-facing, grinding the valve check nuts, Spindle etc. including jointing materials complete all as specified and directed.

Taking out sluice valve of 500mm bore, repairing and refixing the same after re-facing, grinding the valve check nuts, Spindle etc. including jointing materials complete all as specified and directed.

Material and Labour for repairs to air release valve, of 150 mm bore of pipe and refixing the same after replacing the unserviceable HDPE float, nuts, bolts and jointing materials complete all as specified and directed.

Material and Labour for repairs to air release valve, of 200 mm bore of pipe and refixing the same after replacing the unserviceable HDPE float, nuts, bolts and jointing materials complete all as specified and directed.

Supply and fix in repairs sluice valve, cast iron body, stainless steel spindle, gun metal rings including wheel for operation, flanged and drilled, 80 mm bore of pipe, confirming to IS - 14846, class PN -1.6, long body type including all joints with rubber gasket and jointing materials, bolts, nuts, washer complete all as specified and as directed.

Supply and fix in repairs sluice valve, cast iron body, stainless steel spindle, gun metal rings including wheel for operation, flanged and drilled, 100 mm bore of pipe, confirming to IS - 14846, class PN -1.6, long body type including all joints with rubber gasket and jointing materials, bolts, nuts, washer complete all as specified and as directed.

Supply and fix in repairs sluice valve, cast iron body, stainless steel spindle, gun metal rings including wheel for operation, flanged and drilled, 200 mm bore of pipe, confirming to IS - 14846, class PN -1.6, long body type including all joints with rubber gasket and jointing materials, bolts, nuts, washer complete all as specified and as directed.

Supply and fix in repairs sluice valve, cast iron body, stainless steel spindle, gun metal rings including wheel for operation, flanged and drilled, 300 mm bore of pipe, confirming to IS - 14846, class PN -1.6, long body type including all joints with rubber gasket and jointing materials, bolts, nuts, washer complete all as specified and as directed.

Supply and fix in repairs sluice valve, cast iron body, stainless steel spindle, gun metal rings including wheel for operation, flanged and drilled, 400 mm bore of pipe, confirming to IS - 14846, class PN -1.6, long body type including all joints with rubber gasket and jointing materials, bolts, nuts, washer complete all as specified and as directed.

Supply and fix in repairs sluice valve, cast iron body, stainless steel spindle, gun metal rings including wheel for operation, flanged and drilled, 500 mm bore of pipe, confirming to IS - 14846, class PN -1.6, long body type including all joints with rubber gasket and jointing materials, bolts, nuts, washer complete all as specified and as directed.

Material and Labour for rubber gasket / tyton joint confirming to IS specifications for CI / DI pressure pipes of 100 mm bore, socket and spigot or specials complete all as specified and as directed.

Material and Labour for rubber gasket / tyton joint confirming to IS specifications for CI / DI pressure pipes of 200 mm bore, socket and spigot or specials complete all as specified and as directed.

Material and Labour for run lead joint confirming to IS specifications for cast iron pressure pipes of 100 mm bore, socket and spigot or specials complete all as specified and as directed.

Material and Labour for run lead joint confirming to IS specifications for cast iron pressure pipes of 400 mm bore, socket and spigot or specials complete all as specified and as directed.

Material and Labour for run lead joint confirming to IS specifications for cast iron pressure pipes of 500 mm bore, socket and spigot or specials complete all as specified and as directed.

Repairs to 400mm bore non- return valves by opening valve, cleaning the gates with wire brush, removing deposited scales/ foreign materials, rubbing the seat with emery paper and replacing unserviceable gasket and worn out parts etc, and refixing back to original position, complete all as specified and as directed. Make : Kirloskar / Leader / Upadhayaya / BIR

Supplying, fixing and testing of DI, heavy duty, specials of any size, radius and length confirming to IS - 1538 Part - I to XXIII: 1976 such as bends [any type, radius and angle], tapers any type [straight, bend, increasing, decreasing or double socket etc, sockets, tail pieces, connecting pieces, tee pieces, single branch, "Y" junction, double branch, cross, [all sockets or socket and spigot or Flanged], collars, caps and plugs, (required for shape as per site) adopters etc suitable for CI / DI Spigot and Socket or Flanged pressure pipes complete all as specified and as directed.

Material and Labour for preparing old painted or untreated exposed surfaces of GI/ CI / DI Pipes of size 500/ 400 / 300 / 200/ 150/ 100/ 80mm bore, Valve Chamber Covers, clarifloculators, pump motors, railing any type and applying one coat of black coloured weather proof synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Material and Labour for 15 mm bore GI tubing medium grade, galvanised, ISI marked, with all fittings and laid in walls, ceilings, floors and in trenches including taking down old unserviceable pipes complete all as specified and as directed

Material and Labour for 20 mm bore GI tubing medium grade, galvanised, ISI marked, with all fittings and laid in walls, ceilings, floors and in trenches including taking down old unserviceable pipes complete all as specified and as directed

Material and Labour for 25 mm bore GI tubing medium grade, galvanised, ISI marked, with all fittings and laid in walls, ceilings, floors and in trenches including taking down old unserviceable pipes complete all as specified and as directed

Material and Labour for 80mm bore GI tubing medium grade, galvanised, ISI marked, with all fittings and laid in walls, ceilings, floors and in trenches including taking down old unserviceable pipes complete all as specified and as directed

Material and Labour for 100mm bore GI tubing medium grade, galvanised, ISI marked, with all fittings and laid in walls, ceilings, floors and in trenches including taking down old unserviceable pipes complete all as specified and as directed

Material and Labour for 80mm bore HDPE pipe, ISI marked, with all fittings and laid in walls, ceilings, floors and in trenches including taking down old unserviceable pipes complete all as specified and as directed

Material and Labour for 100mm bore HDPE pipe, ISI marked, with all fittings and laid in walls, ceilings, floors and in trenches including taking down old unserviceable pipes complete all as specified and as directed

Material and Labour for detecting leakage in GI/HDPE water supply lines of 100 mm bore in any location, any depth including necessary earthwork excavation and repairing and arresting leakage by providing jointing material (fusion/ mirror joints in case of HDPE pipes), flanged clamps, nuts, M seal, collor washers & bolts and any other items required at site complete all as specified and as directed.

Material and Labour for detecting leakage in GI/HDPE water supply lines of 80 mm bore in any location, any depth including necessary earthwork excavation and repairing and arresting leakage by providing jointing material (fusion/ mirror joints in case of HDPE pipes), flanged clamps, nuts, M seal, collor washers & bolts and any other items required at site complete all as specified and as directed.

Material and Labour for detecting leakage in GI/HDPE water supply lines of 40/50 mm bore in any location, any depth including necessary earthwork excavation and repairing and arresting leakage by providing jointing material (fusion/ mirror joints in case of HDPE pipes), flanged clamps, nuts, M seal, collor washers & bolts and any other items required at site complete all as specified and as directed.

Material and Labour for detecting leakage in GI/HDPE water supply lines of 20/25 mm bore in any location, any depth including necessary earthwork excavation and repairing and arresting leakage by providing jointing material (fusion/ mirror joints in case of HDPE pipes), flanged clamps, nuts, M seal, collor washers & bolts and any other items required at site complete all as specified and as directed.

Supply and fix in repairs, 15 mm bore Gun metal globe or gate valve of class-I, pressure tested of 1.5 MPa with iron wheel head, screwed both ends for iron pipe, ISI marked complete all specified and as directed.

Supply and fix in repairs, 20 mm bore Gun metal globe or gate valve of class-I, pressure tested of 1.5 MPa with iron wheel head, screwed both ends for iron pipe, ISI marked complete all specified and as directed.

Supply and fix in repairs, 25 mm bore Gun metal globe or gate valve of class-I, pressure tested of 1.5 MPa with iron wheel head, screwed both ends for iron pipe, ISI marked complete all specified and as directed.

Supply and fix in repairs, 40 mm bore Gun metal globe or gate valve of class-I, pressure tested of 1.5 MPa with iron wheel head, screwed both ends for iron pipe, ISI marked complete all specified and as directed.

Supply and fix in repairs, 50 mm bore Gun metal globe or gate valve of class-I, pressure tested of 1.5 MPa with iron wheel head, screwed both ends for iron pipe, ISI marked complete all specified and as directed.

Supply and fix in repairs, 80 mm bore Gun metal globe or gate valve of class-I, pressure tested of 1.5 MPa with iron wheel head, screwed both ends for iron pipe, ISI marked complete all specified and as directed.

Supply and fix rolled mild steel work confirming to Fe 410-W, Grade-E- 250, quality-A as in staging for water tanks and the like including ladders for buildings, OHR, semi-UG sump and valve chamber covers etc. caps, bases, splices etc built up from two or more beam or channel or angle sections and plates, including all lattice bars, stiffeners, gusset plates, etc and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer including preparation of surfaces and including dismantling old steel structure of any description complete all as specified and as directed.

Supply and fix in repairs earth continuity conductor or main earthing load of GI strip of 32 x 6 mm, fixed to walls on batten or recess of chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation etc, complete all as specified and as directed.

Supply and fix in repairs test point terminal block made of gun metal or phosphorus bronze of size 75x75x25 mm drilled and screwed including 3 nos 8 mm dia 25 mm long hexagonal head brass screws complete all as specified and as directed.

Supply and fix in repairs single pointed air termination copper rod 12 mm dia and 300 mm long, fixed on overhead reservoirs for lightening protection with necessary connections to earthing complete all as specified and as directed.

Material and Labour for copper earth strip 20x3mm with saddles and fixing screws etc for roof conductors of Lightning protection including taking out old copper strip all as specified and as directed.

M&L for servicing of air blower including replacing oil &air filters, pouring of oil, shaft coupling, applying grease and applying one coat of synthetic enamel paint ,tightening of nuts &bolts complete all as directed by Engr-in-Charge.

S&F in repairs belt (as per sample) of air blower all as specified and as directed by Engr-in-Charge.

Supply and fix in repairs water proof multi-colour LED fountain light fittings 18 W with provision and connecting water proof cables of suitable size and testing complete all as specified and as directed by Engineer -in- Charge

Material and labour for servicing of air compressor including replacing air filters, cartridge (as per sample) pouring of oil complete all as directed by Engr-in-Charge. Note : Rate of any items are required to change/replace while servicing is also deemed to be included in quoted rate

Material and Labour for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Meter below normal ground level connected to GI wire 4 mm dia as main earthing lead (upto 7.5 m length from earth electrode to test point) by means of bolts, nuts , check nuts and GI washers and GI tubing 20 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1, pre cast RCC (1:2:4) type B1 as in cover slab 54 x 54 x 5 cm including 8mm dia MS TMT bars @ 150 mm c/c as in reinforcement with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (medium Grade) for watering, charcoal or coal and salt in alternate layers including excavation earth work in any type of soil, RFR and removal of surplus soil complete all as specified and directed electrical plate No. 3 of SSR part - I complete including taking down of existing old earthing all as specified and as directed.

Gulmarg Electrical Service

KAPOOR AUTOMOBILES

CHANDER SEKER ENTERPRISE

Hindustan Traders