GE 861 EWS-01/2022-2023

Amount

Taking down cement plaster on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors & pavings n.exc 15 cm thickness (below or above ground level), complete all as specified and directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frames) not exceeding 1.50 Sqm each, complete all as specified and directed.

Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) exc 1.5 but n exc n.exc 4 Sqm each, complete as specified and directed.

Taking down shutters of any description exceeding 1.00 Sqm and not exceeding 2.00 Sqm each, and removing from site, complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting , any gauge and thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises,complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Demolition of brick work or stone / boulder masonry, built in cement mortar, including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles etc, complete all as specified and directed.

Dismantling timber scantling unframed 40 sq cm and over in section in any position, complete all as specified and directed.

Dismantling of timber scantling under 40 Sqcm, fixed in any position in fillet rails, posts rafters purlin etc complete all as specified and directed.

Demolition of cement reinforced concrete (reinforcement cut as required to facilitate demolition) in ground floors & pavings n.exc 15 cm thickness (below or above ground level), complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded and pointed in any mortar, complete all as spcified and directed.

Non-skid coloured ceramic tiles 6 to 7 mm thick (square / rectangular) area of each tile exc. 0.18 sqm but not exc 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as spcified and directed.

Glazed ceramic coloured tiles 450mm x 300mm x 6 to 7mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed.

Plain cement concrete M-10, 1:3:6, type C-2, using 40mm graded mechanically crushed stone aggregate, 50mm thick, as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified and directed. Note:- The unit rate include for use of form work (straight or curved).

Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Non-skid coloured ceramic tiles 6 to 7 mm thick (square / rectangular) area of each tile exc. 0.06 sqm but not exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as spcified and directed.

Glazed ceramic coloured tiles 300mm x 200mm x 6mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed.

Brick work with sub class 'B' bricks straight or curved on plan, exceeding 6m mean radius with old size bricks, built in cement mortar 1:6, complete all as specified and as directed.

All as per the description of item No. 22 here-in- before but except bricks.

Steel water tubing, 15 mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

Steel water tubing, 20 mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

10mm thick rendering on fair faces of brick or concrete surfaces in CM 1:6 finished even and smooth without using extra cement, complete all as specified and directed.

15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 finished the surface even and smooth without using extra cement, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of wall and applying two coats of cement base paint over a coat of alkali-resistant priming coat, complete all as specified and directed.

Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer, complete all as specified and directed.

0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap with zinc coating of 275, fixed with 'L' or 'J' type or cranked hook bolts in roofs, walls etc. complete all as specified and directed.

All as per srl item No-30 here in above but except sheets, complete all as per specified and directed.

0.80mm thick plain galvanized mild steel sheeting in ridges, hips valley gutters, drip and straight flashings (length and girth as fixed)with grade of zinc coating 275 complete all as specified and directed.

19mm thick block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work, complete all as specified and directed.

0.90mm thick decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions, complete all as specified and directed.

Demolition wall and ceiling boards (fibre, Pulp, insulation etc) or insulation board/slabs/blankets, any thickness, including cover fillets etc, complete all as specified and directed.

4mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in ceiling flat and sloping with nails to timber frame, complete all as specified and directed.

4mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in walls with nails to timber frame, complete all as specified and directed.

6mm thick plywood, grade BWR, type BB, fixed with screws to timber frame work, complete all as specified and directed.

2nd class soft wood, as in scantling and similar work, clean sawn, timber framed and fixed in position, complete all as specified and directed.

2nd class softwood plain fillets square/rectangular or triangular in section of sectional area exc 13 Sqcm but n exc 25 Sqcm, complete all as specified and directed.

2nd class softwood plain fillets square/rectangular or triangular in section of sectional area n exc 3 Sqcm, complete all as specified and directed.

Preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified.

Preparation of new CGI/PGI steel surfaces of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer over a coating of mordant solution including washing the surfaces, complete all as specified and directed.

75mm dia outlet cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed.

S&F in repair 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210gms), complete all as specified and directed.

S&F in repair 20mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed, complete all as specified and directed.

S&F in repair 15mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed, complete all as specified and directed.

S&F in repair stainless steel sink with drainage board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mmx330mmx160mm complete all as specified and directed.

15mm bore bib tap, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule (fixed in repair), complete all as specified and directed.

15mm bore stop valves, fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union (fixed in repair), complete all as specified and directed.

Steel ventilator with top hung shutter (half portion) including hinges, handles etc complete with glazing bars dovetailed or welded and half portion fixed, including one shop coat of red oxide primer, complete all as specified and directed.

35 mm thick 2nd class softwood plain factory made, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkats, complete all as specified and as directed.

35mm thick, 2nd class softwood factory made glazed and skeleton shutters, open rebated and prepared to receive glass or gauge,etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (a) for door shutter supplying and fitted to chowkats, complete all as specified and directed.

2nd class softwood, plain, solid, straight chowkats and frames, wrought, framed, worught, framed rebated on the solid, rounded of chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

Preparation of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

Preparation of old painted wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified.

300mm helical door springs, including roller and roller plate, complete all as specified and directed.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm & fixed with stainless steel wire staples, complete all as specified and directed.

S&F in repair 4mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed.

150mm long mild steel barrel tower bolts, stove enamelled black, with bright bolts fixed, complete all as specified and directed.

100mm long mild steel barrel tower bolts, stove enamelled black, with bright bolts fixed, complete all as specified and directed.

100 mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed.

75 mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed.

150mm long, mild steel pressed handles, oval type, stove enamelled black, complete all as specified and directed.

100mm long, mild steel pressed handles, oval type, stove enamelled black, complete all as specified and directed.

250mm size mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed.

Disconnecting existing tanks capacity exc 500 Ltrs and n.exc 1000 Ltrs, setting aside (or lowering if required) for cleaning, etc. and hoisting if required reconnecting and re-fixing in position, complete all as specified and directed.

Rotational moulded polythylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball including dismantlling of existing tank, complete all as specified and directed.

Chequered coloured cement concrete tiles of size 300 x 300 x 18-20mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry, laid in floors, over and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

S&F in repairs 110mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors etc, complete all as specified and directed.

RCC M-25 design mix using 20 mm graded aggregate as in slab supported on walls, beams and columns in floors, roofs landings balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

MS TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality conforming to complete all as specified and directed.

Form work to sides and soffits of suspended slab such as roof slab, floor slab, shelves and similar works n. exc. 200 mms thick (Horizontal or sloping), finishing rough the concrete surfaces, complete all as specified and directed.

Brick work with sub class 'B' bricks, straight or curved on plan, to any radius, in half brick thick wall, using old size brick, built in cement mortar 1:4, complete all as specified and directed.

18-20mm thick udaipur green marble stone (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.

20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed.

PCC 1:2:4 type B-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified.

Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, conforming to Fe-410-W (Gde-E-250) quality-A, complete all as specified and directed.

S&F in repairs 20mm dia brass chromium towel rail, complete all as specified and directed.

75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base of floor, complete all as specified and directed.

Machine pressed precast concrete interlocking paver block with grey cement and pigment, any shape, size and design as approved by Engr-in charge confirming to IS 15658-2006 of 60 mm thickness, M-35 grade, laid over and including 40mm thick sand cushion and compacted with mechanical vibrator, complete all as specified and directed.

S&F in repair vitreous china, wash hand basin, oval type, of size 450mm dia with brackets including cutting for and pinning in ends of brackets, including 32mm waste fittings, chromium plated with long screwed shanks & fly nuts, flange end bedded in red lead cement and other end fixed, complete all as specified and directed.

15mm bore pillar tap,fancy type, cast copper alloy, with capstan head, chromium plated screwed down high pressure, with or without lettered hot/cold with long screwed shanks and fly nuts screwed for iron pipe (fixed in repair), complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including unscrewing from board fitting and fixture such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody for reuse if serviceable or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Point wiring with 1.5 Sqmm PVC (FRLS) insulated unsheathed multi stranded copper conductor cable 1100 volts grade single core conforming to IS-694-1990 and including one run of continous earth wire to common earth and connected to earth with 1.5 Sqmm PVC (FRLS) insulated unsheathed multi stranded copper conductor cable draw in & incl PVC surface casing 'N' capping double lock type to be fixed with the help of rawal plugs & screws incl necessary fittings & fixture and to be turminated in sunk cast iron/pressed steel/PVC terminal boxes for mounting switches, sockets, regulators etc with 3 mm thick plastic laminated sheet cover of adequate size for one light point/fan point controlled by one switch, complete all as specified and directed.

All as per srl item No-86 here in above but for one 3 pin 5A socket outlet independent controlled by one switch, complete all as specified and directed.

All as per srl item No-86 here in above but for one 5A socket outlet on the same board controlled by one switch, complete all as specified and directed.

All as per srl item No-86 here in above but for one 3 pin 15 Amps socket outlet independent with 2.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 2.5 Sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green color) as earth lead.

Switch socket combination 2 in 1, 5/6 pin, 5 and 15 Amp, flush type universal complete all as specified and directed.

Switch socket combination 2 in 1, outlet 5 pin, 5 Amp flush type, universal, complete all as specified and directed.

S & F in repair pin type LED lamp 7 W, complete all as specified and directed.

Supply, installation, testing and commissioning of decorative ultra slim linear LED in replacement of 16 Watt , 4 ' long lighting fixture with extruded Al heat sink , environment friendly , energy efficient ready to use pack including LED tube complete with inbuilt electronic driver , PCB , connector block etc including connecting up with three core twisted flexible copper conductor cable with suitable size LED tube including taking out old, all as specified and directed. Make : Havells Cat Part No LHDD02102674 or Equivalent in C&S/Bajaj/Halonix.

Lamp holder, PVC/ Polycarbonate type with back plate, straight/ angular, suitable for batten fittings, complete all as specified and directed.

Switch piano flush button types 5/6 Amp, single pole, one way complete all as specified and directed.

Sub main wiring with two single core PVC insulated flexible copper conductor cable of size 4.0 sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 4.0 Sqmm as earth lead in & including concealed PVC casing capping medium grade 2mm thickness ISI marked or cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification, complete all as specified and directed.

Supply & fixing in repair MCB Distribution board , 240 volts single pole and neutral , double door, sheet steel, enclosure powder coated with 100 Amps rated copper busbar with neutral link, 8 ways, IP-43 protection, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/distempering etc to match the existing surface, complete all as specified and directed.

M&L in repair for MCB single pole 240 volts 6 to 32 amps as per site requirement , with rupturing capacity 10 KA as per IS-8828-1996 (IEC-60898), biconnect upper and lower terminals , integrated label holder to ensure circuit identification complete all as specified and directed.

M&L in repair for isolator single pole and neutral 240 volts 32 to 40 amps as per site requirement , with rupturing capacity 10 KA as per IS-8828-1996 (IEC-60898), biconnect upper and lower terminals , integrated label holder to ensure circuit identification complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level. connecting to the GI wire 4 mm dia by means of bolls, nuts, check nuts and washers of galvanised iron and earth wire protected by provision of GI light grade pipe 15mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM weight not less than 4 Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and handle of 6mm dia MS bar made to shape, GI medium grade 20mm bore pipe for watering , perforated at bottom. 1.75 metre long placed on top edge of earth plate. charcoal and common salt filling with fixing arrangement, funnel wire mesh and earth work in soft soil returning filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate 3 of SSR-2009 Part-I and connecting to earth test point all as specified or indicated including testing on completion. NOTE :- (i) Item of earthing includes cost of 7.5 m long GI wire of size 4 mm dia with protection pipe of 15mm dia GI medium grade, any variation in length shall be adjusted through deviation order based on SSR rates enhanced by (-) 14.50% (MINUS). (ii) On testing after completion of earthing if the desired earth resistance is not obtained earthing will be re-done by the contractor at his own risk and cost.

Socket outlet 2 in 1, 3 pin, 6 Amps flush type, 50 Hz, complete all as specified and directed.

Supply and fixing in repair modular one way switch 6 Amp 240 volts suitable for 1 module, complete all as specified and directed.

Supply and fixing in repair modular socket outlet, 6A/16A-2/3 pin combined 2 module, 230 volts complete all as specified & directed.

Supply and fixing in repair modular socket outlet, 6A-2/3 pin combined 2 module, 230 volts complete all as specified and directed.

Supply and fixing in repair modular one way switch 16A, 1 module single pole, 230 volts complete all as specified & directed.

LED light fitting mirror type with high out put diffuser 2x2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

Supply and fixing in replacement fan regulator electronic, step type hum free suitable to control speed of fan from 0 to 100% and connecting electrically all as required at site or directed.

S & F in repair bell push, flush type, 5 Amp, complete all as specified and directed.

S & F in repair bell, ding dong, AC 230 Volt, 50 Hz including wooden/PVC board for suitable size, connecting and testing, complete all as specfied and directed.

Ceiling rose 3 terminal bakelite 65mm x50mm surface type, PVC/ Polycarbonate, isolated body, complete all as specified and directed.

M&L in repair for MCB TPN 415 volts 40-100 amps, 'C' curve as per site requirement , with rupturing capacity 10 KA as per IS-8828-1996 (IEC-60898), biconnect upper and lower terminals , integrated label holder to ensure circuit identification complete all as specified and directed.

Supply and fix in repair sheet metal enclosure MCB distribution board, single pole and neutral double door with IP-43 protection single phase 240 volts 4 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.

Supply and fix in repair MCCB Distribution board, TP&N , vertical , double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link,415 Volts 8 way fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete including 3 Pole V-Tec MCCB of 100 A rating & 25kA breaking capacity, 415 Volt,MCCB pre-fitted at factory, complete all as specified and directed.

S&F in repair down rod 300 mm long heavy duty suitable for 1200/1400 mm sweep ceiling fan, complete all as specified and directed.

M/S MIR SAJAD ENTERPRISES

M/S A.N CONSTRUCTIONs

Adil Mohammad Dijoo

M/S AK ENTERPRISES

M/S HAMID & CO

M/s Hilal Constructions