REPAIR AND MAINTENANCE OF DG SETS AND CLEANING AND MAINTENANCE OF SWIMMING POOL UNDER AGE EM OF GE NAGROTA

Amount

SCHEDULE-A PART-I (DG SET) M & L for Dismantaling /Opening of upper portion of Disel Engine 320 KVA to 125 KVA (Make : Greaves/ Kirloskar/ Cummins or any other make) air cooled,turbo charged ,Vertical type for top over hauling, repair/ servicing of engine including taking out rediator /fuel pump,water Pump,Turbo charger etc (Egnine oil and coolent reaquired for this job is deemed to be included in the quoted rate. (a) Dismantaling/Opening of complete cyllinder head assebly rockers arms assemblypiston head assembly ,sleeves byremoving nuts &bolts for repair complete. (b) Servicing & washing of complete engine partswith kerosine oil ( c) Re- assembling of engine after replacementof UNSV/defective parts with new parts as listed in given below per Job shall be deemed to be included in this rates and testing of engine as per company recommendation after reassembling all parts as directed to the satifaction of the Engr-in -Charge Note : Repair and Transportation (BY JCB / HYDRA OR ANY OTHER MEANS) charge for carrying out repair & reinstall on same installation back shall be deemed to be included in this rates

Supply & fix in replacement of following parts given below , rates shall be deemed to be above job included .

Valve Exhaust

Valve inlet

Insert Valve Seat

Guide Valve

Cup Injector

Fip Element

Gasket Set

Hose Pipe

Fuel Filter

Lubrication Oil Filter

Super By Pass Fillter

Hose Clip Set

Piston set Complete

Ring Set Complete

Cyllinder Linner

Connecting Rod Bearing

Gasket Set Cyllinder Head

Callibration of Fuel Pump

Head Repair Work

Callibration of injectors of Nozzels

Lubrication Oil Pump

O ' Ring Set Complete

Set of Fuel Flexible Pipe

Stem Seal

M & L for Dismantaling /Opening of upper portion of Disel Engine 125 KVA to 62.5 KVA (Make : Greaves/ Kirloskar/ Cummins or any other make) air cooled,turbo charged ,Vertical type for top over hauling, repair/ servicing of engine including taking out rediator /fuel pump,water Pump,Turbo charger etc (Egnine oil and coolent reaquired for this job is deemed to be included in the quoted rate. (a) Dismantaling/Opening of complete cyllinder head assebly rockers arms assemblypiston head assembly ,sleeves byremoving nuts &bolts for repair complete . (b) Servicing & washing of complete engine partswith kerosine oil ( c) Re- assembling of engine after replacementof UNSV/defective parts with new parts as listed in given below per job shall be deemed to be included in this rates and testing of engineas per company recommendation after reassembling all parts as directed to the satifaction of the Engr-in -Charge Note : Repair and Transportation (BY JCB / HYDRA OR ANY OTHER MEANS) charge for carrying out repair & reinstall on same installation back shall be deemed to be included in this rates

Supply & Fix in replacement of following parts given below rates shall be deemed to be above job included .

Valve Exhaust

Valve inlet

Insert Valve Seat

Guide Valve

Cup Injector

Fip Element

Gasket Set

Hose Pipe

Fuel Filter

Lubrication Oil Filter

Super By Pass Fillter

Hose Clip Set

Piston set Complete

Ring Set Complete

Cyllinder Linner

Connecting Rod Bearing

Gasket Set Cyllinder Head

Callibration of Fuel Pump

Head Repair Work

Callibration of injectors of Nozzels

Lubrication Oil Pump

O ' Ring Set Complete

Set of Fuel Flexible Pipe

Stem Seal

M & L for Dismantaling /Opening of upper portion of Disel Engine 62.5 KVA to 20 KVA (Make : Greaves/ Kirloskar/ Cumiuns or any other make) air cooled,turbo charged ,Vertical type for top over hauling, repair/ servicing of engine including taking out rediator /fuel pump,water Pump,Turbo charger etc (Egnine oil and coolent reaquired for this job is deemed to be included in the quoted rate. Dismantaling /Opening of upper portion of Disel Engine 125 KVA to 62.5 KVA (Make : Greaves/ Kirloskar/ Cummins or any other make) air cooled,turbo charged ,Vertical type for top over hauling, repair/ servicing of engine including taking out rediator /fuel pump,water Pump,Turbo charger etc (Egnine oil and coolent reaquired for this job is deemed to be included in the quoted rate. (a) Dismantaling/Opening of complete cyllinder head assebly rockers arms assemblypiston head assembly ,sleeves byremoving nuts &bolts for repair complete . (b) Servicing & washing of complete engine partswith kerosine oil ( c) Re- assembling of engine after replacementof UNSV/defective parts with new parts as listed in given below per job shall be deemed to be included in this rates and testing of engineas per company recommendation after reassembling all parts as directed to the satifaction of the Engr-in -Charge Note : Repair and Transportation (BY JCB / HYDRA OR ANY OTHER MEANS) charge for carrying out repair & reinstall on same installation back shall be deemed to be included in this rates

Supply & Fix in replacement of following parts given below rates rates shall be deemed to be above job included .

Valve Exhaust

Valve inlet

Insert Valve Seat

Guide Valve

Cup Injector

Fip Element

Gasket Set

Hose Pipe

Fuel Filter

Lubrication Oil Filter

Super By Pass Fillter

Hose Clip Set

Piston set Complete

Ring Set Complete

Cyllinder Linner

Connecting Rod Bearing

Gasket Set Cyllinder Head

Callibration of Fuel Pump

Head Repair Work

Callibration of injectors of Nozzels

Lubrication Oil Pump

O ' Ring Set Complete

Set of Fuel Flexible Pipe

Stem Seal

M & L for Servicing of DG Sets of capacity 250 KVA /320 KVA of make (Make : Greaves/ Kirloskar/ Cummins or any other make) by the authorised Engineer of respective manufacturer of DG Set continous operational condition including the following checkings all as specified and directed by Engr-in -charge (Egnine oil and coolent reaquired for this job is deemed to be included in the quoted rate. (Note:- Any part during servicing gate damage will be changed by the contractor without any extra cost , cost willl be deemed to be included in the quoted job).(i) Removing the existing engine oil, clean the oil sump and refilling with required quantity of new engine oil 20W40 & coolant upto top. (ii) Checking of fan motor hub (iii) Checking exhaust and inlet manifold belt and cap screw (iv)Cleaning of radiator inside and out side thoroughly and cleaning with solution (caustic soda) to the entire satisfaction of Eng-in-charge by removing and re-fixing in original position after cleaning.(v) Checking and adjusting injector and valves, tappet and replace the gasket including cost of gasket.(vi) Cleaning fuel inlet connections and screw, (vii) Checking of vibration damper and rectified. (viii) Servicing of turbocharger by checking, leakage tightening of mounting screws & nuts and replace oil.(ix) Checking water temperature safety control (x) Checking and correcting up impeller of water pump for excess play. (xi) Servicing of governer and Changing of governor oil. (xii) Checking and adjusting all fan belt.(xiii) Any other check as per manufacturer`s instructions Note:- Necessary spare parts required if any will be measured and paid under relevant items

S & F replacement in Kit, fuel filter and ring

S & F replacement in Element for Lubrication oil filter.

S & F replacement in Kit, Element of super bypass filter.

S & F replacement in Seal, O Ring and Air cleaner.

S & F replacement in Kit Conversion

S & F replacement in Gasket, Rocker lever cover

All as per item no.7 above but for DG Sets of Capacity 180 KVA DG set,

S & F replacement of Kit, fuel filter and ring

S & F replacement of Element for Lubrication oil filter.

S & F replacement of Kit, Element of super bypass filter.

S & F replacement of Seal, O Ring and Air cleaner.

S & F replacement of Kit Conversion

S & F replacement of Gasket, Rocker lever cover

All as per item no.7 above but for DG Sets of Capacity 125/ 100 KVA DG set

S & F replacement of Kit, fuel filter and ring

S & F replacement of Element for Lubrication oil filter.

S & F replacement of Kit, Element of super bypass filter.

S & F replacement of Seal, O Ring and Air cleaner.

S & F replacement of Kit Conversion

S & F replacement of Gasket, Rocker lever cover

All as per item no.7 above but Diesl Engine of 62.5/ 63/50 KVA DG set

S & F in replacement of Kit, fuel filter and ring

S & F in replacement of Element for Lubrication oil filter.

S & F in replacement of Kit, Element of super bypass filter.

S & F in replacement of Seal, O Ring and Air cleaner.

S & F in replacement of Kit Conversion

S & F in replacement of Gasket, Rocker lever cover

All as per item no.7 above but DG Sets of Capacity 40/30 KVA DG set

S & F in replacement of Kit, fuel filter and ring

S & F in replacement of Element for Lubrication oil filter.

S & F in replacement of Kit, Element of super bypass filter.

S & F in replacement of Kit Conversion

S & F in replacement of Gasket, Rocker lever cover

All as per item no.7 above but DG Sets of Capacity 25/20/15 KVA DG set

S & F in replacement of Kit, fuel filter and ring

S & F in replacement of Element for Lubrication oil filter.

S & F in replacement of Kit, Element of super bypass filter.

S & F in replacement of Seal, O Ring and Air cleaner.

S & F in replacement of Kit Conversion

S & F in replacement of Gasket, Rocker lever cover

M&L for Rewinding of armature of Dynamo/alternators 12V/24V volts with `F' class copper wire to match existing gauge including dismantling of old coil , cleaning thoroughly winding with super enameled copper wire of existing size and gauge,varnishing, drying etc and fixed with dynamo/alternator properly tesing and commissioning all as specified all and directed by Engr-in-Charge.

S & F repair radiator hoses of size 40mm dia or as per existing dia and 60 cm length for any capacity of DG set including jublee clip, clamp nuts etc are properly fixed and connected.as directed to the satifaction of the Engr-in -Charge

S & F in replacement of flexible pressure pipe for lubricant size of 60 cm length for oil and fuel connection for complete suitable for 180/100/82.5 KVA/63 KVA Engineas directed to the satifaction of the Engr-in -Charge

Supply and filling Engine oil 20W/40f make (Castroll/Kirloskar/HP) complete all as specified and directed.

S& Fill distilled water packed in sealed gallan of 5 Ltrs complete all as specified and directed.

Supply and filling water coolant(diluted)in radiator (make volve line or equivalent) including removal of old water/coolant, all as directed by Engineer-in-Charge.

M & L for Dismantling and removing of water pump assembly of any capacity any type of DG Set complete from the engine,repair/overhauling the same by replacing tornout components like bearing,impeller,bushes, oil seal,water seal,gaskets etc. reassembling,refixing and testing complete as directed to the satifaction of the Engr-in -Charge

M & L for Repair/overhauling of self starter 12V/24V including replacement of worn out clutch assembly,bush,spring,plunger assembly, solenoid switch,carbon brushes,brush spring etc.as directed to the satifaction of the Engr-in -Charge for the 250 KVA DG Set

M & L for Repair/overhauling of self starter 12V/24V including replacement of worn out clutch assembly,bush,spring,plunger assembly, solenoid switch,carbon brushes,brush spring etc.as directed to the satifaction of the Engr-in -Charge for the 180/125 KVA DG Set

M & L for Repair/overhauling of self starter 12V/24V including replacement of worn out clutch assembly,bush,spring,plunger assembly, solenoid switch,carbon brushes,brush spring etc.as directed to the satifaction of the Engr-in -Charge for the 100 KVA to 63 KVA DG Set complete all as specified and directed.

M & L for Repair/overhauling of self starter 12V/24V including replacement of worn out clutch assembly,bush,spring,plunger assembly, solenoid switch,carbon brushes,brush spring etc.as directed to the satifaction of the Engr-in -Charge for the 20/25/40 KVA DG Set complete all as specified and directed.

M & L for replacement of totally damaged self starter 12V/24V complete assembly suitable for any capacity of DG Set complete all as specified and directed.

M & L for Repair/overhauling of dynamo including replacement carbon, brushes holder, spring, commutator /slipring assembly bearing, regulator etc. of any make, type and capacity.complete all as specified and directed.

Supply and fix in replacement of electrically operated fuel shut down valve assembly complete testing and commissioning as specified and directed by Engr.in-charge including dismantling and removal of old U/S valves of any capacity DG set. complete all as specified and directed.

M & L for Servicing/repairs of AMF panel complete including cleaning resetting/adjustment of relays,calibration of time delay relays, checking and replcement of diods, if required ,resistors contactor etc. complete for any make/type and capacity of DG sets.

M & L for Disconnecting and dismantling the alternator unit of 250 KVA DG Set from the base plate of the DG set and transporting to workshop for repair, dismantling the unit, further separating the armature from the startor carefully, cutting and taking out the burnt windings of the alternator carefully, cleaning the slots and , duly applying the insulation and assembling the stampings inserting in position in the startor including applying slot insulation and rewinding of the alternator startor winding with super enameled copper conductor of same gauge and same number of turns as that of existing one including replacement of carbon brushes tapping the windings and bringing out the coil conections for production of 3 phase 415 volt 50 HZ AC supply and preheating the windings and applying insulating varnish and drying the windings in oven and assembling the unit and transporting back to installation and fixing on base plate and coupling with the DG set and testing complete all as specified and directed.

M & L for Disconnecting and dismantling the alternator unit of 180/125/100 KVA DG Set from the base plate of the DG set and transporting to workshop for repair, dismantling the unit, further separating the armature from the startor carefully, cutting and taking out the burnt windings of the alternator carefully, cleaning the slots and , duly applying the insulation and assembling the stampings inserting in position in the startor including applying slot insulation and rewinding of the alternator startor winding with super enameled copper conductor of same gauge and same number of turns as that of existing one including replacement of carbon brushes tapping the windings and bringing out the coil conections for production of 3 phase 415 volt 50 HZ AC supply and preheating the windings and applying insulating varnish and drying the windings in oven and assembling the unit and transporting back to installation and fixing on base plate and coupling with the DG set and testing complete all as specified and directed.

M & L for Disconnecting and dismantling the alternator unit of 63 KVA DG Set from the base plate of the DG set and transporting to workshop for repair, dismantling the unit, further separating the armature from the startor carefully, cutting and taking out the burnt windings of the alternator carefully, cleaning the slots and , duly applying the insulation and assembling the stampings inserting in position in the startor including applying slot insulation and rewinding of the alternator startor winding with super enameled copper conductor of same gauge and same number of turns as that of existing one including replacement of carbon brushes tapping the windings and bringing out the coil conections for production of 3 phase 415 volt 50 HZ AC supply and preheating the windings and applying insulating varnish and drying the windings in oven and assembling the unit and transporting back to installation and fixing on base plate and coupling with the DG set and testing complete all as specified and directed.

M & L for Disconnecting and dismantling the alternator unit of 50/25 KVA DG Set from the base plate of the DG set and transporting to workshop for repair, dismantling the unit, further separating the armature from the startor carefully, cutting and taking out the burnt windings of the alternator carefully, cleaning the slots and , duly applying the insulation and assembling the stampings inserting in position in the startor including applying slot insulation and rewinding of the alternator startor winding with super enameled copper conductor of same gauge and same number of turns as that of existing one including replacement of carbon brushes tapping the windings and bringing out the coil conections for production of 3 phase 415 volt 50 HZ AC supply and preheating the windings and applying insulating varnish and drying the windings in oven and assembling the unit and transporting back to installation and fixing on base plate and coupling with the DG set and testing complete all as specified and directed.

M & L for Disconnecting and dismantling the alternator unit of 20/10 KVA DG Set from the base plate of the DG set and transporting to workshop for repair, dismantling the unit, further separating the armature from the startor carefully, cutting and taking out the burnt windings of the alternator carefully, cleaning the slots and , duly applying the insulation and assembling the stampings inserting in position in the startor including applying slot insulation and rewinding of the alternator startor winding with super enameled copper conductor of same gauge and same number of turns as that of existing one including replacement of carbon brushes tapping the windings and bringing out the coil conections for production of 3 phase 415 volt 50 HZ AC supply and preheating the windings and applying insulating varnish and drying the windings in oven and assembling the unit and transporting back to installation and fixing on base plate and coupling with the DG set and testing complete all as specified and directed.

Supply and fix in replacement of diode assembly complete suitable to match the existing one of 250 KVA alternator excitor unit. complete all as specified and directed.

Supply and fix in replacement of diode assembly complete suitable to match the existing one of 180/125/100KVA alternator excitor unit. complete all as specified and directed.

Supply and fix in replacement of diode assembly complete suitable to match the existing one of 63/50/40/30 KVA alternator excitor unit. complete all as specified and directed.

Supply and fix in replacement of diode assembly complete suitable to match the existing one of 12.5/20/25 KVA alternator excitor unit. complete all as specified and directed.

Supply and fix in replacement of PVC insulated battery lead with 16 Sq.mm copper conductor cable of length 2/3 mtr with copper/brass clamps and lugs for fixing on battery terminals and self starter complete as specified and as directed.

Supply and fix in replacement of rectifiers for alternators suitable for Gensets upto 40/63/82.5/100/110KVA capacity complete as specified and as directed.

Supply and fixing in carbon brushes suitable for alternators upto 250 KVA gensets. complete as specified and as directed.

Supply and fix in replacement of RPM meter complete with cable and accessories at the last range 0 to 2500 complete as specified and as directed.

Supply and fix in replacement of water temperature gauge complete with cable and accessories at the last range 0 to 150 degree centigrate complete as specified and as directed.

Supply and fix in replacement of oil temp gauge as per existing site requirement complete as specified and as directed.

Supply and fix in replacement of oil pressue gauge as per existing site requirement complete as specified and as directed.

M & L for Dismantling the defective Fuel Injector Assembly of any capacity from the existing foundation and engine including taking down all electrical connections transporting to approved authorised workshop, after setting up opening the complete, connector plate, gasket & complete overhauling re- assembling the Fuel Injector after transporting back to site re-installing carrying out alignment of complete DG set reconnecting up all electrical connections testing and commissioning complete the following capacity of DG set (Note:- (a) Rate quoted shall be deemed to be inclusive making good the distrubed surfaces (b) The DG set shall be tested for the satisfaction of Engr -in -charge to achive designed parameters.

180 KVA capacity DG Set

125/100/62.5/50 KVA DG

40/30/25/20 KVA DG

S & F in repair battery terminal brass superior quality suitable for 180 AH 12 Volts Battery complete all as specified and directed.

Supply and fixing in replacement of ignition switch and key of 110/100/ 82.5 KVA DG Set complete all as specified and directed.

Supply and fixing in replacement of ignition switch and key of 63/40 KVA DG Set complete all as specified and directed.

Supply and fixing in replacement of AVR unit of 250 KVA to 100 KVA for matching the existing AVR unit, complete all as specified and directed by Eng-in charge.

Supply and fixing in replacement of AVR unit of 63 KVA to 40 KVA for matching the existing AVR unit, complete all as specified and directed by Eng-in charge.

Supply and fixing in replacement of AVR unit of 25/20/10 KVA for matching the existing AVR unit, complete all as specified and directed by Eng-in charge.

S&F in replacement of contactor suitable for AMF panel contactor MNX 32 3pole 240V as per existing contactor of site complete all as specified and directed.

S&F in replacement of contactor suitable for AMF panel contactor MNX 25 3pole 240V as per existing contactor of site complete all as specified and directed.

S&F in replacement of contactor suitable for AMF panel contactor MNX 16 3pole 240V as per existing contactor of site complete all as specified and directed.

S&F free lead acid battery 12 volts 180 AH complete all as specified and as directed by Engr-In-Charge.

M&L for servicing/ cleaning of MS diesel tank of DG set 180/160/100 KVA by draining out the diesel from tank, cleaning the tank with soap water/ suitable solution and painting the external surface with one coat of synthetic enamel paint of existing colour including repalcement of drain valve, outlet pipe complete all as specified and as directed.

M&L for servicing/ cleaning of MS diesel tank of DG set 62.5/40/50/25 KVA by draining out the diesel from tank, cleaning the tank with soap water/ suitable solution and painting the external surface with one coat of synthetic enamel paint of existing colour including repalcement of drain valve, outlet pipe complete all as specified and as directed.

S&F in replacement of MCCB, four pole, 160 Amp 415 volts, 50 Hz breaking capacity not less than 25 kA with adjustable thermal and adjustable magnetic protection release with spreader links, Ics = 100% Icu complete all as specified and as directed

S&F in replacement of MCCB, four pole, 125 Amp 415 volts, 50 Hz breaking capacity not less than 25 kA with adjustable thermal and adjustable magnetic protection release with spreader links, Ics = 100% Icu complete all as specified and as directed

S&F in replacement of MCCB, four pole, 100 Amp 415 volts, 50 Hz breaking capacity not less than 25 kA with adjustable thermal and adjustable magnetic protection release with spreader links, Ics = 100% Icu complete all as specified and as directed

S&F in replacement, fan belt suitable for 12.5 KVA DG set complete all as specified and as directed.

S&F in replacement, fan belt suitable for 20/25//30 KVA DG set complete all as specified and as directed.

S&F in replacement, fan belt suitable for 40/50 KVA DG set complete all as specified and as directed.

S&F in replacement, fan belt suitable for 62.5/63 KVA DG set complete all as specified and as directed.

S&F in replacement, fan belt suitable for 125/100 KVA DG set complete all as specified and as directed.

S&F in replacement, fan belt suitable for 180 KVA DG set complete all as specified and as directed.

S&F in replacement, fan belt suitable for 250 KVA DG set complete all as specified and as directed.

M & L for Dismantling/ taking down complete radiator assembly of DG set 180 KVA and transporation to market for repair by :- (i) Opening the radiator assembly with brazing/ welding for repair/ services. (ii) Cleaning of all water tube with diluted solution of HCL & cleaning with water preasure & removing the sludge and dust from inside the tank by flushing out. (iii) Repair of fins by soldring/ brazing. (iv) Repair of bottom brass water tank by soldring/ brazing. (v) Repair of radiator hose assembly. (vi) Fixing the complete radiator assembly to its orignal position and testing complete

M & L for Dismantling/ taking down complete radiator assembly of DG set 125/100 KVA and transporation to market for repair by :- (i) Opening the radiator assembly with brazing/ welding for repair/ services. (ii) Cleaning of all water tube with diluted solution of HCL & cleaning with water preasure & removing the sludge and dust from inside the tank by flushing out. (iii) Repair of fins by soldring/ brazing. (iv) Repair of bottom brass water tank by soldring/ brazing. (v) Repair of radiator hose assembly. (vi) Fixing the complete radiator assembly to its orignal position and testing complete

M & L for Dismantling/ taking down complete radiator assembly of DG set 62.5 KVA and transporation to market for repair by :- (i) Opening the radiator assembly with brazing/ welding for repair/ services. (ii) Cleaning of all water tube with diluted solution of HCL & cleaning with water preasure & removing the sludge and dust from inside the tank by flushing out. (iii) Repair of fins by soldring/ brazing. (iv) Repair of bottom brass water tank by soldring/ brazing. (v) Repair of radiator hose assembly. (vi) Fixing the complete radiator assembly to its orignal position and testing complete

M & L for Dismantling/ taking down complete radiator assembly of DG set 20/25/40 KVA and transporation to market for repair by :- (i) Opening the radiator assembly with brazing/ welding for repair/ services. (ii) Cleaning of all water tube with diluted solution of HCL & cleaning with water preasure & removing the sludge and dust from inside the tank by flushing out. (iii) Repair of fins by soldring/ brazing. (iv) Repair of bottom brass water tank by soldring/ brazing. (v) Repair of radiator hose assembly. (vi) Fixing the complete radiator assembly to its orignal position and testing complete

Supply , laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavu duty aluminium conductor LT 1100 V grade cross sectional area 50 sq 3.5 core, complete all as specified and directed by Engineer-in-Charge

Supply , laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavu duty aluminium conductor LT 1100 V grade cross sectional area 70 sq 3.5 core, complete all as specified and directed by Engineer-in-Charge

Supply , laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavu duty aluminium conductor LT 1100 V grade cross sectional area 35 sq 3.5 core, complete all as specified and directed by Engineer-in-Charge

Supply , laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavu duty aluminium conductor LT 1100 V grade cross sectional area 25 sq 4 core, complete all as specified and directed by Engineer-in-Charge

S&F in replacement of Change over switch off load type with enclosure, conforming IS 13947 part I & III 415V, 4 pole of rating 100 amps, including taking out unservicable one complete all as specified and directed by Engineer-in -Charge.

S&F in replacement of Change over switch off load type with enclosure, conforming IS 13947 part I & III 415V, 4 pole of rating 200 amps, including taking out unservicable one complete all as specified and directed by Engineer-in -Charge.

S&F in change over switch on load type with enclosure, conforming IS 13947 part I & III 415V, 4 pole of rating 100 amps, including taking out unservicable one complete all as specified and directed by Engineer-in -Charge.

Supply and fix in in replacement of 24 Volt Relay ,taking down and reconnecting up all electrical connections testing and commissioning complete as directed to the satifaction of the Engr-in -Charge

Supply and fix in replacement of 12 Volt Relay ,taking down and reconnecting up all electrical connections testing and commissioning complete as directed to the satifaction of the Engr-in -Charge

Supply and fixing in replacement of Didital volt meter as per existing size complete all as specified and directed.

Supply and fixing in replacement of Digital Amp meter as per existing size complete all as specified and directed.

Supply and fixing in replacement of Digital Frequency meter as per existing size complete all as specified and directed.

Supply and fixing of Block Head Assembly of 62.5 KVA (Make : Kirloskar) with all ites supporing parts and making it functional.

Supply and fixing in replacement of indicator lamp assembly complete LED type suitable for the existing system supply voltage for the existing system supply voltage 230V / 440 V AC including taking down old lamp assembly

M & L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised iron strip 32x6 mmdia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion

SCHEDULE-A PART -II (SWIMMING POOL) M& L for Dewatering of Raw water from filter bed at Swimming poll including mud by pumping or bailing out muddy water from filtration plant which can not be drained out by operation of valves, complete all as specified and directed by Engr-in-Charge.

M & L for Taking out silt and mud deposited at the filtration plant and removal at a distance not exceeding 50 mtr from the starting point (filtration plant), complete all as specified and directed by Engr-in-Charge.

M&L for taking out quartz sand of different sizes and removal at a distance not exceeding 50 mtr from starting point, complete all as specified and directed by Engr-in-Charge.

Supply and laying of quartz sand of required size for filter media clean & washed of size 0.35 mm – 1.6 mm upto 3.5 m depth on filteration plant , complete all as specified and directed by Engr-in-Charge.

Supply and fixing of nozzle strainers, for Fitreation plant fixing with suitable sockets of suitable dia, complete all as specified and directed by Engr-in-Charge.

Supply and fixing following connecting items of swimming pool filtration plants are as under

Supply and Fixing Rubber Gasket for top cover for swimming pool rapid sand filtration plant of suitable dia complete all as specified and directed by Engr-in-Charge.

Supply and Fixing Pressure Gauge meter for swimming pool rapid sand filtration plant of suitable dia complete all as specified and directed by Engr-in-Charge.

Supply and Fixing Pressure Flanged of suitable dia and connecting pipe required of suitable dai for swimming pool rapid sand filtration plant complete all as specified and directed by Engr-in-Charge. Note: For Ser no 89 to 97 Dewatering of Dug wells/Sumps/Over Head Tank will be carried out with the help of motor and with in one day without break down / interupted of water supply of any area .The rate shall be deemed to include in the quoted rate.

Supply and mix Potash alum crystal (Fitkari )suitable for purification of Swimming pool water in the form of solid lumps/slabs from the manufacturer having valid BIS certificate as specified in table 1 of IS: 299-2012 complete all as specified and directed by Engr-in-Charge. .

Supply and mix calcium Hypo Chlorite granular in factory sealed HDPE container (45 Kg each) decomposing at 177 C , Mol Wt : 142.98, Toxicity: Oral rat LD : 850mg /kg having chlorination concentration level 70%. Make- Puri Chlor (Sree Rayalaseema Hi-Strength Hypo Ltd),M/S SVS Aqua Technologies or equivalent in other approved make by E-in-C's Br.

Supply and adding of following chemicals for treatment of water to keep the swimming pool water free from fungus & bacteria.

Copper sulphate of approved qualtiy complete all as specified and directed by Engr-in-Charge

Soda Ash of approved quality complete all as specified and directed by Engr-in-Charge

Crystal Bright Swimming Pool Clarifier of approved quality complete all as specified and directed by Engr-in-Charge

S&F Suction sweeper base brush of size 92cm x 7cm x 4cm suitable for suction sweeper asembly, with nylon hair brush with bristles of length 7cm and 1mm dia each. complete all as specified and directed by Engr-in-Charge Note :- Same as existing brush .

S&F PVC nylon flexible hose squairral pipe 40mm outer dia size, heavy-duty capacity suitable for suction sweeper.complete all as specified and directed by Engr-in-Charge

Supply and fix Clean Net Spa Leaf Rake Wire Mesh Frame With 10 feet Aluminum Pole all as specified and directed by Engr-in-Charge

Supply and fix in Nylon rope for suction sweeper all as specified and directed by Engr-in-Charge

M & L for Chamber cover with 25x25x4mm thick MS Angle iron frame and 3.0 mm thick MS chequd plate cover with hinges and necessary locking arrangements painting with two coats of synthetic enamel paint over one coat of red oxide primer existing collour all as specified and directed by Engr-in-charge Note:- Size of Chamber cover as per existing chamber

Supply and Fixing Pressure Flanged of suitable dia and connecting pipe required of suitable dia for swimming pool rapid sand filtration plant complete all as specified and directed by Engr-in-Charge. Note:- Pipe length required as per side requirement .The rate shall be deemed to include in the quoted rate.

Supply and fix wall brush (18 inch) With 10 feet Aluminum Pole complete all as specified and directed.

Supply and fixing in replacement of submersible cable un armored PVC insulated & sheathed copper conductor cable 1100 Volts grade of size 16 Sqmm 3 core complete all as specified and directed.

Supply and fix Algae brush (18 inch) With 10 feet Aluminum Pole all as specified and directed by Engr-in-Charge

Supply & F in Pool suction sweeper /Vaccum head of 40 mm dia as required and directed by Engr-in-charge Note :- Suction sweeper including brushes sample as per existing suction sweeper .The rate shall be deemed to include in the quoted rate.

M&L for earthing complete with galvanized steel earth plate electrode of size 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level surrounded on all sides by 150 mm thick charcoal & common salt starting from ground below earth plate upto 150mm above GI plate in alternate layers connected to GI strip 24 mm x 4 mm by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh of 22 gauge, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI pit all as shown in electrical plate No 3 of MES SSR Part-I (2009) as specified including provision of 40mm dia medium grade GI pipe for earth strip protection and 20 mm dia for watering complete , all excavation and earth work & connecting the earthing to an earthing test point /LT Panel as specified and testing on completion for desired result complete all as specified and directed by Engr-in-charge.

Material and labour for heavy duty butterfly valve 150mm dia complete with iron wheel conforming to IS 1969,PN 1.6 of double flanged and drilled end provided with high tensile steel spindle including GI flanged Bolts/Nuts/washers gasket etc all and removal of old valve of following sizes :

S & F in replacement to foot valve 150 mm dia in position by replacement of UNSV parts such as Brass ring packing/Rubber packing , nuts, bolts, washers rubber insertion sheet complete all as required to make it functional complete all as specified & directed

Material and labour for valve chamber on existing chamber foundation with 230mm thick brick wall in CM 1:6, 75mm thick coping in PCC 1:2:4 (Type B1), 15mm thick plaster in CM 1:4 over all internal and external wall surface, 25x25x4mm thick MS Angle iron frame and 3.0 mm thick MS chequd plate cover with hinges and necessary locking arrangements painting with two coats of synthetic enamel paint over one coat of red oxide primer all as specified and directed including dismantling and removal of existing damaged chamber except PCC foundation of internal size 1000 x1000 x 1000mm :-

Material and labour for heavy duty sluice valve 150 mm dia complete with iron wheel conforming to IS 1969,PN 1.6 of double flanged and drilled end provided with high tensile steel spindle including GI flanged Bolts/Nuts/washers gasket etc all and removal of old valve of following sizes :

M & L for cleaning to chamber / chambers internal surfaces of RCC balancing Tank having capacity 0.25 lakh gallon any type by removing bleaching powder/Al-Tock residue, silt sand, mud, funges etc with steel wire brush and getting out. Cleaning, washing and flushing including writing done/due date of cleaning with synthetic enamelled white paint on black back ground (Black back ground shall be painted with synthetic enamelled black paint), After cleaning and after preparing complete. The cost of Material and labour For repair of Inside tank deemed to be included all as specified and directed by Engr-in-Charge. Note: Saperate log book should be maintain for record of maint U/G sump and log book provided by contractor.

Supply and fixing in replacement of MCCB 200 Amps 3 pole 415 Volts 36 KA with adjustable thermal and adjustable magnetic settings fixed in repair as per existing at site and complete all as specified and directed.

Supply and fixing in replacement of MCCB 100 Amps 3 pole 415 Volts 16 KA fixed type as per existing at site and complete all as specified and directed.

Supply and fixing in replacement of MCCB 63 Amps 3 pole 415 Volts 16 KA fixed type as per existing at site and complete all as specified and directed.

TARA ENTERPRISES (BID ID -3362569)

M/S J S ENGINEERS (BID ID -3362124)