GER-53/2021-22 Special repair E/M works in certain bldg at 150 GH including certain sanctioned works under GE 862 EWS

Amount

Sch 'A' Part-I (B/R works) Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nanital or similar pattern roof coverings complete all as specified and directed.

S&F for pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws including side and end lap as per manufacturer’s instructions complete all as specified and directed.

S&F for pre-painted galvalume aluminium zinc coated GI based plain steel sheet 0.50mm thick of approved colour having tensile strength 550 Mpa as in ridges, hips, valley gutters, fixed with self tapping screws including side and end lap as per manufacturer’s instructions complete all as specified and directed.

Dismantling timber scantling 40 Sq cm and over in section, in any position (framed work) complete all as specified and directed.

M&L for mild steel structural steel work confirming to Fe-410-S including tubular members as in main and cross beams, hip and jack rafter, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates and painted with a shop coat of zinc chromate primer before hoisting and fixing in position complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing rubbish off the premises complete all as specified and directed.

M&L for vitrified tiles light shade (premium quality) 10 mm thick (square/ rectangular) polished, area of each tiles not exc 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, laid over and including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

M&L for vitrified tiles light shade (premium quality) 10 mm thick (square/ rectangular) polished, area of each tiles not exc 0.36 sqm in vertical surfaces, skirting/dado, pillers etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, laid over and including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (premium quality) Square/rectangular, area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size 450x350x7mm/ 350x250x7mm (premium quality) on vertical surface such as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 10 mm thick backing layer of cement plaster in cement mortar (1:4) complete all as specified and as directed.

M&L for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

M&L for stone walling of random rubble masonry, uncoursed, well bonded, bedded and soilidly hearted, built in cement mortar (1:6), complete all as specified and directed.

M&L for stone walling of random rubble masonry (except stones, using old unserviceable stone after cleaning), uncoursed, well bonded, bedded and soilidly hearted, built in cement mortar (1:6), complete all as specified and directed.

Taking down cement plaster, any description on brick or stone or cement concrete surfaces including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar (1:4) on stone masonry finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 20 mm thick in cement mortar (1:6) on stone masonry finished even and smooth without using extra cement complete all as specified and directed.

M&L for complete removal of existing treatment form old decorated surfaces of walls and applying two coats of cement base paint over one coat of chalk whitening complete all as specified and directed.

M&L for applying two coats of cement base paint over one coat of primer on new plastered surfaces complete all as specified and directed.

M&L for complete removal of existing treatment form old decorated surface of walls and applying two coats of distemper oil emulsion complete all as specified and directed.

M&L for applying two coats of distemper oil emulsion paint ove one coat of primer on new plastered surface complete all as specified and directed.

Taking down chowkhats or frames with shutter (without taking off shutter from the frame) exc 1.5 Sqm and n.exc 4 Sqm each and removing to store complete all as specified and directed.

S&F for pressed steel door frame of size 125x60 mm with one or more rebates including necessary fixing lugs, hinges, lock and strike plate etc including back filling to chowkhats in PCC (1:3:6) type C-0 using 12.5mm graded stone agregate complete all as specified and directed.

S&F for factory made 2nd class hard wood 35 mm thick plain framed panelled shutters (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part-I) kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F for factory made 35 mm thick 2nd class hard wood glazed and skelton shutters open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats complete all as specified and directed.

S&F for 100mm long butt hinges medium weight cold rolled mild steel complete all as specified and directed.

S&F for 50mm long butt hinges medium weight cold rolled mild steel complete all as specified and directed.

S&F for 150 mm long extruded aluminium alloy handles fabricated type anodised complete all as specified and directed.

S&F for 150mm long aluminium anodized barrel tower bolts extruded section all as specified and directed.

S&F for 300mm long aluminium alloy, anodised, sliding door bolt, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

M&L for hacking out broken glass (any thickness size, quality or description from wooden frames glazed with putty/beads complete all as specified and directed.

S&F for 3mm thick sheet glass ordinary quality and glazing with oil putty/wooden beads in square n exc. 5 sqm in each pane complete all as specified and directed.

M&L for preparation of new steel surface exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified.

M&L for preparation of new wooden surface exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old wooden surface and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old steel surface and applying one coat of synthetic enamel paint complete all as specified.

S& F for stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperature 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Taking up or down GI tubing 15 mm bore and connections including cleaning for refixing or removal complete all as specifed and directed.

Taking up or down GI tubing 20 mm bore and connections including cleaning for refixing or removal complete all as specifed and directed.

S&F for 15 mm bore galvanized iron GI tubing medium grade with all fittings such as bends, socket, Tee, Elbow, union, Nipple, short pieces and fixed to walls, ceilings or laid in floors complete all as specified and directed.

S&F for 20 mm bore galvanized iron GI tubing medium grade with all fittings such as bends, socket, Tee, Elbow, union, Nipple, short pieces and fixed to walls, ceilings or laid in floors complete all as specified and directed.

S&F for 32mm dia waste coupling of brass chromium plated for glazed ware sinks, basin etc with long screwed shanks and fly nuts, flange and bedded in red lead cement mortar complete as in repair all as specified and directed.

S&F for 15 mm bore brass CP wash hand basin mixer hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

M&L for 15mm dia bib tap cast copper alloy with crutch or butterfly handle, chromium plated, fancy type, screwed for iron pipe complete as in repair as in repair all as specified and directed.

S&F for vitreous China wash basin, white, flat back, size 600x 480mm including cutting for and pinning in ends of brackets or errecting stand, angle bracket (but exclusive of fixing of supply waste pipe, tap) complete all as specified and directed.

S&F for PVC connection 15 mm x 450 mm including PTMT nuts at both ends screwed for iron pipe of 15 mm bore complete all as specified and directed.

S&F for PVC waste pipe 600mm long suitable for wash hand basin and urinals including connecting complete all as specified and directed.

M&L for 15mm bore stop valve (angular), cast copper alloy screwed down, high pressure with crutch or butterfly handle, chromium plated, screwed both ends for iron pipe or for unions and fixed complete as in repair all as specified and directed.

M&L for 75mm dia cast iron floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

M&L for kitchen sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete as in repair all as specified and directed.

S&F for 15mm bore fancy type pillar taps, cast copper alloy, with capstan heads, brass chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete as in repair all as specified and directed.

S&F for soap dish, chromium plated, 100x100x60mm, fixed to wall plugs with chromium plated screws complete all as specified and as directed.

S&f for stainless steel kitchen plate rack of 20 gauge over all size 600mmx750mmx220mm of standard pattern and approved make complete as in repair all as specified and directed.

S&F for brass chromium plated tubular towel rail 20 mm dia "D" type 60 cm long between flange, aluminium anodised complete all as specifed and directed.

S&F for 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

M&L for 75mm thick PCC type C-2, (1:3:6) (using 40mm graded stone aggregate) as in plinth protection, laid in slope 1:12 from outer edge of the wall, finished even and fair, laid in alternate bays including providing 6mm wide joints throughtout thickness of plinth protection in concrete bays and in between walling and plinth protection, joints filled mastic filling comprising of one part of heated bituminous 85/25 and 3 parts of sand (all by weight) complete all as specified and directed.

S&F for rotational moulded polythylene water storage tank (ISI marked) with float valve, plastic lid cover, multy-layered, cylindrical vertical with closed top, hoisted and fixed in position of capacity 1000 ltrs including dismantling old unserviceable tank and making connections inlcuding suitable GI wash out, over flow, nipple and including 20mm bore ball brass valve with union screwed for iron pipe and fixed complete all as specifed and directed.

M&L for 4mm thick designer cement fibre ceiling board in ceiling fixed with screw as per manufacturers instructions , laid over and including hot dipped galvanised iron in post grid with 24mm wide T section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33 mm thick galvanised steel sheet of size 24 x 32 x 300 mm spaced at 12 mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 4 mm dia to be fixed by approved rawl plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall flush fittings of 1200 mm long screws Tee with (double stiching) to interlocked between main runners at 600 mm centre to centre from 1200 x 600 mm modules cross tee longer than 600 mm modules to be formed by fittings 600 mm long cross tee, tee perimeter wall angle shall be of 0.45 mm thick galvanised steel of size 19 x 19 mm and 300 mm long of white colour all as per insturctions including dismantling of existing board etc complete all as specified and directed.

Demolition of cement concrete reinforced in ground floor and paving n exc 15 cm thickness complete all as specified and directed.

M&L for plain cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) as in coping, benching, hold fasts, water troughs, bed block, surface channel and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed.

M&L for formwork to edges of concrete flats, breaks in floor, opening in concrete walls, floors and roof and sides of RCC/PCC bands in walls, horizontal or sloping and similar work all exceeding 20cm wide with finished fair faces complete all as specified and directed.

M&L for 50mm thick PCC (1:3:6), type C-2 using 20mm graded stone aggregates as in sub base of floors and mass concrete complete all as specified and directed.

M&L for 75mm thick PCC (1:4:8), type D-2 using 40mm graded stone aggregates as in sub base of floors and mass concrete complete all as specified and directed.

M&L for colour chequered cement concrete tiles of size 30 cm x 30cm x 25 mm thick, set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 20 mm thick cement screed bed in cement mortar (1:6) complete all as specified and as directed.

M&L for hard core of broken stone or boulder of gauge n.exc 63mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and well rammed to a true surface complete all as specified and as directed.

M&L for Brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius, built in cement mortar (1:6) complete all as specified and directed.

M&L for Steel windows factory made with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded all as per IS-1038 complete all as specified and directed.

M&L for Steel windows factory made with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded all as per IS-1038 complete all as specified and directed.

M&L for Use & waste of formwork to sides and soffits of floor of roof beam, deck slab, shelfs, plinth beam etc and similar works in rough finished flat surface of concrete complete all as specified and directed.

M&L for RCC (1:2:4) type B-1 (using 20mm graded aggregate) as in beam, cantilever, lintel over 1.5m span complete all as specified and directed.

M&L for mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Mild steel TMT bars 6mm to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends as in stirrups, spacers and binders including binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 5mm to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends as in stirrups, spacers and binders including binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Excavation over area not exc. 1.5 m depth for foundation etc in hard/dense soil and getting out complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block of any shape and size approved by EIC, ISI marked (IS:15658-2006) 80mm thick, M-40 grade (Medium Traffic), in paths and hardstanding,with grey cement and pigment, laid tightly over & including 25mm thick dry sand cushion (compacted) and joints filled with dry sand, colour and pattern as approved by GE, complete all as specified and directed.

M&L for providing, cement concrete type B1, 1:2:4 (using 20mm graded aggregates) in roof kerbs or mud stops, rounded or chamfered on edgecomplete all as specified and directed.

M&L for extra over stone walling for hammer dressing to face stones and dressing of face beds with maximum depression on face from straight edge held against the dressed surface n exc 40 mm and joints, as specified, of random rubble walling, uncoursed or brought upto courses complete all as specified and directed.

M&L for raised pointing to random or polygonal rubble, uncoursed or brought upto courses in cement mortar (1:4) complete all as specified and directed.

M&L for surface dressing n exc 15cm in soft/loose soil complete all as specified and directed.

M&L for Anodised aluminium frame for doors, windows and ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

M&L for Anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, mortice lock, 1 No, floor door stopper, anodised aluminium snap beading, screws etc including powder coating of any colour (thickness of powder coating not less than 50 micron) complete all as specified and directed.

M&L for Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, mortice lock, 1 No, floor door stopper, anodised aluminium snap beading, screws etc including powder coating of any colour (thickness of powder coating not less than 50 micron) complete all as specified and directed.

S&F for 5.5mm thick sheet glass ordinary quality and glazing with oil putty/wooden beads in square n exc. 5 sqm in each pane complete all as specified and directed.

M&L for RCC 1:2:4, type B1 (using 20mm graded aggregates) as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for RCC 1:2:4, type B1 (using 20mm graded aggregates) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for RCC 1:2:4, type B1 (using 20mm graded aggregates) as in suspended slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for formwork to sides ofcolumns, post, struts, piers and stenchions for finished surface complete all as specified and directed.

M&L for use & waste of formwork to sides of concrete foundation, footing, bases of colums, raft & raft beams, sides and soffits (if any) of foundation and plinth beam and similar works in rough finished flat surface of concrete complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, landings and similar work; n exc 200mm thick (Horizontal and sloping) for rough finished surface of concrete complete all as specified and directed.

M&L for framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290, Gde E-165 complete all as specified and directed.

Sch 'A' Part-II (E/M works) Taking down carefully copper/ aluminum point wiring (light, fan, socket or power) complete, including all fittings such as switches, ceiling roses, pendants, regulators sockets etc.) removing material from the site and making good the disturbed surfaces of walls, floor or ceiling etc. to match with existing specifications complete all as specified and directed.

M&L for point wiring for one light point/fan/bell/buzzer point controlled by one-one way switch with 1.5 Sqmm. (nominal area) single core FRLS,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor unsheathed in and including non metalic rigid PVC casing & caping of 25mm width (Medium grade double locking system) complete with all acessories including PVC sunk box ISI marked for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, and 1.5 Sqmm. (nominal area) single core FRLS, PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable as earth wire upto common earth and connected to earth dolly including making good the diturbed surfaces compete all as specified and directed. (Note:- Three run of copper conductor of required size and one run of casing capping measured as one unit)

Description all as per Serial item No 93 above but for one 5 pin 6 Amp socket outlet on independent board controlled by one 6 amp switch complete all as specified and directed.

Description all as per Serial item No 93 above but for one 5 pin 6 Amp socket outlet on same board controlled by one 6 amp switchcomplete all as specified and directed.

Description all as per Serial item No 93 above but for one 6 pin 15 Amp socket outlet independent with 2.5 sqmm PVC insulated FRLS multistraind copper cable with 2.5 sqmm single core multistraind FRLS copper cable as earthling lead complete all as specified and directed.

M&L for Switch piano, flush type single pole, one way 6 Amp, 240 volts complete all as specified and directed.

M&L for switch socket combination 2 in 1, 5 pin 5 amp flush type complete all as specified and directed.

M&L for Switch socket combination 3 pin 5 Amp/16 Amp, 230 volts, 5 in 1 flush type complete all as specified & directed.

M&L for Socket outlet 6 pin 5 amp and 15 Amp flush type complete all as specified and directed.

M&L for Socket outlet 5 pin 5 amp flush type complete all as specified and directed.

M&L for Ceiling rose two to three terminal (65 x 50mm), PVC/ polycarbonate insulated body complete all as specified and directed.

M&L for Lamp holder insulated body PVC/ Polycarbonate type with back plate suitable for batten/angular/pendent fittings including LED lamp 15 watt complete all as specified and directed.

M&L for Ceiling fan regulator elctronic, stepped type, hum free suitable to control speed of fan from 0 to 100% rotary type five step 240 volts AC complete all as specified and directed.

S&F for environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head 10 watt 6000 K inbuilt LED luminaire comprising of high brightness LEDs, IP54 protection including connecting electricaly using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm complete as in repair all as specified and directed. (Make :- Havells Cat part No HEXAFT10WLED857SSYMBOPC/Crompton Greaves Cat No. LBHP-10-CDL or equivalant of Philips)

M&L for LED Tube light fitting, complete with 1x 18 watts, 220V, AC decorative box type with driver, holder in and including LED tube light connection complete prewired and connecting electrically to ceiling rose to fitting using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core and connector block etc and necessary fixing arrangement at any height complete as in repair all as specified and directed. (Make :- Havells cat No LHEXAPP7IN1W018/Crompton Greaves Cat No LCTLN-18-CDL or equivalent in Philips

M&L for LED Tube light fitting, complete with 1x 20 watts, 220V, AC decorative box type with driver, holder in and including LED tube light connection complete prewired and connecting electrically to ceiling rose to fitting using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core and connector block etc and necessary fixing arrangement at any height complete as in repair all as specified and directed. (Make :- Havells cat No LHEXAPP7IN1W020/Crompton Greaves Cat No LCTLN-20-CDL or equivalent in Philips.

S&F in repairs High efficacy 2'x2' recess LED flat panel light fittings 36W LED 6000K edge-lit luminaire with in and including LED lamp suitable for armstrong/grid ceiling complete for low ceiling applications complete with all accessories pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete as in repair (Make :-Havells, Cat part PLUTONEO02X2PLR34WLED840S / Crompton Greaves, Cat No LCTLSNE-36-FO-CDL or equivalent of philips.

S&F for bell push, flush type, 6 amps complete all as specified and directed.

S&F for call bell AC, 230 volts single pole, ding-dong sound type complete all as specified and directed.

M&L for sheet metal enclosure MCB distribution board, double door single pole and neutral with IP-66 protection single phase 240 volts 8 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete as in repair all as specified and directed. (Note:- MCBs will be measured separately.)

M&L for MCB single pole, 240 volts any rating from 6 to 32 amps, 'C' series/curve with rupturing capacity 10 KA, including providing thimble for out going cablescomplete all as specified and directed.

M&L for MCB single pole & neutral 240 volts any rating from 6 to 32 amps, 'C' series/curve with rupturing capacity 10 KA, including providing thimble for out going cablescomplete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level, earth plate surrounded by and packed with 15 cm thick layer of char coal dust and common salt, earth lead GI wire 4.00 mm dia by means of bolts, Nuts, Check Nuts and washers of galvanized iron and thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15 mm bore and water pipe 20 mm bore GI light grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 & RCC cover all as specified & shown in elect plate No. 3 of SSR part I of 2010 including testing on completion complete after dismantling of old unserviceable earthing all as specified.

S&F for exhaust fan of size 300mm heavy duty metalic body complete with louver 1400 RPM speed 230 volts AC electrical operated 50 HZ complete all as specified and directed.

S&F for street light bracket made out of 40mm bore GI tubing medium grade made to shape 1.2 mtr long bent to shape 120 degree and fixing with two numbers of MS clamp of 50mm x 6mm thick flat iron including , nuts, bolts, washer duly painted with synthetic aluminium paint two coats over a coat of red oxide primer complete all as specified and directed.

S&F for street light bracket made out of 32mm bore GI tubing medium grade made to shape 1.2 mtr long bent to shape 120 degree and fixing with two numbers of MS clamp of 50mm x 6mm thick flat iron including , nuts, bolts, washer duly painted with synthetic aluminium paint two coats over a coat of red oxide primer complete all as specified and directed.

Supply, Laying, connecting and testing in replacement of service cable of size 10 Sqmm 2 core 1100 volts grade heavy duty cable PVC insulated stranded alumn conductor, served with an inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 mtr apart including 4mm suspension wire or drawn in and including medium grade non metallic rigid PVC conduit as per site requirement, flat or circular complete after taking down old unsserviceable cable all as specified and directed.

Taking down existing ceiling fan any type and capacity with due care and refixing after servicing and painting including connecting electrically using PVC insulated overall seathed flexible copper conductor cable 0.75Sqmm complete all as specified and directed.

S&F for LED driver suitable for high efficacy 2'x2' recess LED flat panel light 36 watt with due care and refixing the fitting after servicing including connecting electrically using cord flexible 3 core PVC insulated overall seathed flexible copper conductor cable 0.75Sqmm complete all as specified and directed.

Supply, Laying, connecting and testing in replacement of service cable of size 16 Sqmm 2 core 1100 volts grade heavy duty cable PVC insulated stranded alumn conductor, served with an inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 mtr apart including 4mm suspension wire or drawn in and including medium grade non metallic rigid PVC conduit as per site requirement, flat or circular complete after taking down old unsserviceable cable all as specified and directed.

Supply, Laying, connecting and testing in replacement of service cable of size 4 Sqmm 2 core 1100 volts grade heavy duty cable PVC insulated stranded alumn conductor, served with an inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 mtr apart including 4mm suspension wire or drawn in and including medium grade non metallic rigid PVC conduit as per site requirement, flat or circular complete after taking down old unsserviceable cable all as specified and directed.

Supply, install, commissioning and testing vertical storage water heater (geyser) 5 star rated as per BEE norms electricity operated suitable for 230 volts, 50 hz, AC supply system complete with porcelen/ glass coated insulated heating element, copper tank, external thermostat and docorative of capacity 25 Ltrs, including 01 No. CP connection for hot water and 01 No PVC connection for cold water including fixing on suitable bolts and nuts complete all as specified and directed.

S&F for factory made sheet metal enclosure, double door, 415 volts, AC, TPN vertical distribution board 12 way painted with epoxy based powder coated suitable for mounting MCCB as incomer of rating upto 160 Amps, FP, rating upto 36 KA and MCB SP/TP as outoing and complete with including 200 Amps rated copper busbar, neutral bar, earth bar, conneting cable links with and including top bottom removeable gland plate complewte with IP 43 protection complete in repair all as specified and directed. (Note:- MCBs will be measured separately.)

S&F for factory made sheet metal enclosure, double door, 415 volts, AC, TPN vertical distribution board 4 way painted with epoxy based powder coated suitable for mounting MCCB as incomer of rating upto 160 Amps, FP, rating upto 36 KA and MCB SP/TP as outoing and complete with including 200 Amps rated copper busbar, neutral bar, earth bar, conneting cable links with and including top bottom removeable gland plate complewte with IP 43 protection complete in repair all as specified and directed. (Note:- MCBs will be measured separately.)

M&L for sheet metal enclosure MCB distribution board, double door single pole and neutral with IP-66 protection single phase 240 volts 12 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete as in repair all as specified and directed. (Note:- MCBs will be measured separately.)

M&L for MCCB triple pole and netural 415 volts any rating from 63 amp, with rupturing capacity 25KA, including provinding thimble for out going cable complete all as specified and as directed.

S&F for MCB, 4 pole, 63 amp, 10KA, 'C' series 415 volts complete all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground earth pit not less than 2.25m deep below ground level with top edge of the plate not less than 1.5m deep below normal ground level connected to and including 25X4mm thick galvanised iron strip by means of bolts, nuts, checknuts and washers of galvanised iron or steel all as specified in electrical plate No 3 of SSR (2009) part-I including 40mm bore GI pipe light grade for protection of earth strip and PCC 1:2:4 type B-1 as in pit, Precast RCC earth pit cover 8 cm thick reinforced with 8mm dia TMT bars @150mmc/c and two handles, excavation and earth work in any type of soil and alternate layers of charcoal, common salt and 20mm bore galvanised medium grade steel tubing for watering with one end fixed with cast iron funnel and wire mesh and testing on completion complete after taking down old unserviceable earthing all as specified and directed. (Note:-Earth strip and protection pipe upto board is included in the rate quoted).

S&F for sheet metal enclosure single pole and neutral with two pin and earth plug and socket with one single pole MCB 20 amp complete as in repair all as specified and directed.

Supply,laying, jointng and testing, XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade of size 50 sqmm 3.5 core laid in trenches, ducts, pipes, on poles and connection with necessary cables lugs, glands nut bolts complete after taking down old unserviceable cable all as specified and directed. (Note :- Excavation of earth work, removing, returning filling in, sand cushoining, concrete cable cover and protection GI pipe shall be measured and paid separetly and length of calbe shall be one length unless otherwise as directed by GE).

Supply,laying, jointng and testing, XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade of size 35 sqmm 3.5 core laid in trenches, ducts, pipes, on poles and connection with necessary cables lugs, glands nut bolts complete after taking down old unserviceable cable all as specified and directed. (Note :- Excavation of earth work, removing, returning filling in, sand cushoining, concrete cable cover and protection GI pipe shall be measured and paid separetly and length of calbe shall be one length unless otherwise as directed by GE).

Supply,laying, jointng and testing, XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade of size 25 sqmm 3.5 core laid in trenches, ducts, pipes, on poles and connection with necessary cables lugs, glands nut bolts complete after taking down old unserviceable cable all as specified and directed. (Note :- Excavation of earth work, removing, returning filling in, sand cushoining, concrete cable cover and protection GI pipe shall be measured and paid separetly and length of calbe shall be one length unless otherwise as directed by GE).

Supply,laying, jointng and testing, XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade of size 16 sqmm 4 core laid in trenches, ducts, pipes, on poles and connection with necessary cables lugs, glands nut bolts complete after taking down old unserviceable cable all as specified and directed. (Note :- Excavation of earth work, removing, returning filling in, sand cushoining, concrete cable cover and protection GI pipe shall be measured and paid separetly and length of calbe shall be one length unless otherwise as directed by GE).

Supply,laying, jointng and testing, XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade of size 10 sqmm 2 core laid in trenches, ducts, pipes, on poles and connection with necessary cables lugs, glands nut bolts complete after taking down old unserviceable cable all as specified and directed. (Note :- Excavation of earth work, removing, returning filling in, sand cushoining, concrete cable cover and protection GI pipe shall be measured and paid separetly and length of calbe shall be one length unless otherwise as directed by GE).

Supply,laying, jointng and testing, XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade of size 16 sqmm 2 core laid in trenches, ducts, pipes, on poles and connection with necessary cables lugs, glands nut bolts complete after taking down old unserviceable cable all as specified and directed. (Note :- Excavation of earth work, removing, returning filling in, sand cushoining, concrete cable cover and protection GI pipe shall be measured and paid separetly and length of calbe shall be one length unless otherwise as directed by GE).

M&L for sub main wiring complete with 2 run of 4 sqmm, single core, copper conductor cable 1100 volts grade, FRLS type, PVC insulated, unsheathed, flexible, multi stranded duly colour coded cable drawn through and including PVC casing and caping of size 25mm width or above as required at site and accessories such as tee, corners,overlaping connector etc of suitable size fixed on surface of walls/roofs/ceiling and including 01 run of 4 sqmm single core, copper conductor cable 1100 volts grade, FRLS type, PVC insulated, unsheathed, flexible, multi stranded of green colour as earth continuity conductor connected to common earth dolly including removing old unserviceable sub main wiring items complete all as specified and directed. Note : - 02 run of 4 sqmm single core copper conductor cable and one run of 4 sqmm single core copper conductor cable and 01 run of PVC casing and caping shall be measured as one unit.

M&L for sub main wiring complete with 2 run of 6 sqmm, single core, copper conductor cable 1100 volts grade, FRLS type, PVC insulated, unsheathed, flexible, multi stranded duly colour coded cable drawn through and including non rigid PVC casing and caping (medium grade dobule locking system) of size 25mm width or above as required at site and accessories such as tee, corners,overlaping connector etc of suitable size fixed on surface of walls/roofs/ceiling and including 01 run of 6 sqmm single core, copper conductor cable 1100 volts grade, FRLS type, PVC insulated, unsheathed, flexible, multi stranded of green colour as earth continuity conductor connected to common earth dolly including removing old unserviceable item complete all as specified and directed. Note : - 02 run of 6 sqmm single core copper conductor cable and 01 run of 6 sqmm single core copper conductor and 01 run of PVC casing and caping shall be measured as one unit.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth not exceeding 10sqm on plan for laying of cable and foundation of poles stays and getting out in soft / loose soil complete all as specified and directed.

Returning, filling in trenches including spreading, leveling watering and well ramming in layers not exceeding 25 cm thick complete all as specified and as directed.

Removing of excavated material to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified and directed.

M&L for dry sand cushioning to underground cable, provided with a layer 8 cm thick before and 15 cm deep after laying and stretching jointing and testing the cable complete all as specified and as directed. (Note: Punned thickness of sand shall be measured and paid).

M&L for brick covering with width equal to length of brick as mechanical protection to cable using sub class ‘B’ bricks laid flat, size 230mm x 115mm x 75mm, complete all as specified and as directed.

M&L for 50mm dia galvanized steel tubing (light grade) with complete all fittings such as elbow, unions, nipples, tees, bends, short pieces, connections, check-nuts, caps, plugs, diminishing pieces and flanges etc as in pole, crossing of roads, laid in trenches, fixed on walls for protection complete all as specified and directed.

M&L for MCCB triple pole & neutral 415 volts any rating from 100 Amps, with ruptring capacity 35 KA, for out going cables complete all as specified and directed.

S&F for LED street light fitting 70 watts, made in pressure diecast housing with eppoxy power coated dark graphite grey colour finish, parismatic polycarbonate cover with individual LED lense with IP 66 complete with all accessories and necessary fixing arrangement on wall at any height including three core 0.5 sqmm copper cable from connector to fitting and after taking down old unserviceable light fitting of any type complete as in repair all as specified and directed. (Make:- Crompton, Model No. NEXUS NEO,LSTP-70-CDL-HPM or Havells Cat No. ENDURA PEARLPLUSSL70WLED757PASYTOPCASTHO)

M&L for sheet metal terminal box of size 30cm x 30cm x15cm made out of 2mm thick CRCA sheet, factory made power coated consisting of Aluminum bus bar of size 20x3mm -04 Nos (3phase & 1 Neutral) and MCB SP 10 Amps 01 No Complete all as specified and directed. Make :- Sintex/Hansel.

S&F for ceiling fan 1200 MM sweep with 5 star rating electrical operated 220 volts 50 HZ AC Supply complete with hook arrangement for hanging with canopy and down rod complete with all accessories and PVC copper conductor flexible wire complete all as specified and directed.

Note:- The contract sum arrived after deduction of amount of Sch of credit as listed in tender Documents.

M/s Liaqat Hussain Construction Company

M/S RAHUL GUPTA