SPECIAL REPAIR TO BLDG NO P-2 (APRROX LENGTH 45M) AND P-3 AT SEWAR FORT BHARATPUR MIL STN

Amount

Taking down cement plaster or cement lime plaster on PCC/stone surface/ brick surfaces/ceiling etc. including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick on brickwork or concrete surfaces in CM (1:4) on external surfaces finished even and fair without using extra cement etc complete all as specified and directed.

M&L for rendering 15mm thick on brickwork or concrete surfaces in CM (1:6) on external surfaces finished even and fair without using extra cement etc complete all as specified and directed.

M&L for rendering 5 mm thick in CM (1:3) on ceiling finished even and fair without using extra cement etc complete all as specified and directed.

M&L dubbing out average 15mm thick on irregular face or wall (when specifically ordered in writing) Cement plaster (1:4) etc complete all as specified and directed.

M&L for preparing newly plastered surfaces and applying two coats of cement base paint on wall etc. complete all as per specified and directed.

M&L for sand paper gentle rubbing to obtain smooth surfaces and applying two coats of oil bound distempering white or tinted (copolymer based resin glue to be added for longer durability and better finish) using hand roller over one coat of water based white pigmented alkali resistant priming paint ,over 1mm thick wall care putty on wall surface including all necessary arrangement for execution of work etc complete all as specified and as directed by Engineer-in-Charge.

M&L complete removal of existing treatment of old plastered surfaces on wall surfaces and applying two coats of cement base paint as per approved colour etc complete all as specified and directed by Engineer-in Charge.

M&L for preparing new plastered surfaces and applying three coats of white wash on ceilings etc. complete all as per specified and directed.

M&L complete removal of existing treatment of old plastered surfaces or unplastered surfaces and applying three coats of white wash on ceilings etc. complete all as per specified and directed.

M&L preparation of old distempered surface of wall including cornices etc by brooming down, steel wire brushing ,scraping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots removing nails and filling small holes by putty and rubbing surface by sand paper to prepare the surface and applying one coat of distemper oil emulsion using hand roller white or tinted over 1mm thick wall care putty on wall surface etc complete all as specified and as directed by Engineer-in-Charge.

Demolition of brickwork or stone/boulder masonry, built in lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles etc complete all as specified & directed.

M&L for Brick work sub class B bricks straight or curved on plan exceeding 6 mtr mean radius built in cement mortar (1:6) etc complete all as specified and directed.

Demolition Cement concrete (unreinforced ) concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) etc complete all as specified and directed.

M&L for broken stone or boulders in hardcore of gauge exceeding 63 mm but not exceeding 100 mm deposited spread and levelled in layers not exceeding 15 cm thick watered and rolled/rammed to a true surface etc complete all as specified and directed.

M&L 75 mm thick cement concrete (1:4:8) type D2 using 40mm graded aggregate as in sub base of flooring etc complete all as specified and directed.

M&L for matt finished vitrified tile of size (300x300x9.8)mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 15mm thick base of cement mortar (1:4) (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiling to store and rubbish off the premises etc complete all as specified and directed.

M&L Glazed ceramic digital tiles, matt/glossy finish in vertical surface in required combination of themes, area of each tiles exceeding 0.9 sqm but not exceeding 0.27 sqm, 7-8 mm thick set and jointed in neat cement slurry, over 15mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles etc complete all as specified and directed.

M&L providing and laying double charged vitrified floor tiles in 600X600mm sizes (thickness to be specified by the manufacturer),in required combination of themes, with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours(Dark/Light) and shades, laid on 15 mm thick cement mortar (1:4) (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc complete all as specified and directed.

M&L coloured non skid ceramic tiles (coloured) 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including providing 10mm thick screed bed in CM (1:4) etc complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons laid bedded and pointed in any mortar and removal of same from outside MOD land etc complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25 mm thick over cement screed 20 mm thick in cement mortar (1:6), laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

M&L for Machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dedo and pillar laid over cement screed 15 mm thick in cement mortar (1:4), laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Cutting, polishing of existing kota/marble stone flooring,(cuttings and mirror polishing) including mason polishing, levelling certain kota/marble stone slabs, including necessary repair work complete as directed at site.

Taking down chowkats or frame with shutter (without taking off shutters from the frame) not exceeding 1.5 sqm each and removing to store etc complete all as specified and as directed.

Taking down shutter of any description area exceeding 1 sqm and not exceeding 2 Sqm each etc complete all as specified and as directed.

Taking down door shutters including chowkats (without taking of shutters) exceeding 1.5 sqm but not exceeding 4 sqm etc complete all as specified and as directed.

M&L factory made steel window with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded including one shop coat of zinc chromes primer etc complete all as specified and as directed. Note :- Mild steel wire cloth shall be measured and paid separately under respective items

M&L factory made steel window with side hung shutters including projecting type hinges with steel handle and steel peg stay complete without glazing bars dovetailed or welded including one shop coat of zinc chromes primer etc complete all as specified and as directed. Note :- Mild steel wire cloth shall be measured and paid separately under respective items

S&F of 35 mm thick 2nd class hardwood factory made plain framed, panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces size of members as per IS 1003 Part-I, kiln seasoned and chemically pressure treated etc complete all as specified and as directed.

S&F of 35 mm thick 2nd class hardwood factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauge etc., sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a) etc complete all as specified and as directed.

S&F of steel ventilator with top hung shutter including hinges, steel peg stay, handle complete and a shop coat of zinc chrome primer etc complete all as specified and as directed.

S&F framed work such as grills, gratings, etc, with ends of bars shouldered and / or riveted, or forged into spikes ; framed guard bars ; barred iron doors ; ladders; framed balusters; walkways ; railings ; framework of water tanks and similar work conforming to Fe-290 Gde E-165 etc complete all as specified and directed.

S&F of MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde E-165 including necessary welding etc. and fixed in position etc complete all as specified and directed.

S&F of 100 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkhat including welding etc complete all as specified and directed.

S&F 150mm long extruded aluminium alloy handle fabricated type anodised etc complete all as specified and directed.

S&F aluminium anodised barrel tower bolts of extruded section and fixed 150mm length of bolt etc complete all as specified and directed.

S&F of MS sliding door bolt, plate type, 300mm long, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts & nuts, 4 on bolt plate and 2 on staple plate and fixed etc complete all as specified and directed.

S&F stainless steel cloth 0.36mm nominal dia of wire and 1.40mm average aperture and fixed with stain less steel wire staples etc complete all as specified and directed.

S&F in repair stainless steel cloth 0.36mm nominal dia of wire and 1.40mm average aperture and fixed with stain less steel wire staples etc complete all as specified and directed.

S&F anodised aluminium powder coating of any colour (thickness or power coating not less than 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified Supplied and fixed.

S&F anodised aluminium powder coating of any colour (thickness or power coating not less than 50 micron) door shutters aluminium section weighing 0.55 kg/ m including necessary joining cleats glazing clips, ruber neoprene packing. handles 2 Nos in each door, hinges anodised aluminium snap beading screws etc. complete all as specified and directed.

S&F Aluminium extruded section body door closer hydraulically regulated designation No 3 universal type suitable for door shutter up to 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed etc. complete all as specified and directed.

S&F of 5.5mm thickness sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5sq.m in each pane etc complete all as specified and directed.

S&F three track three panels sliding window of powder coated aluminium with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm), including aluminium extruded interlocks, EPDM rubber gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, etc complete as per approved drawing & direction of Engineer-in-Charge.

Hacking out old broken glass any thickness, size, quality or description from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads including providing 3 mm thick plain sheet glass ordinary quality in square not exceeding 0.5sq.m in each pane etc complete all as specified and directed.

S&F of 3mm thickness sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5sq.m in each pane etc complete all as specified and directed.

M&L preparing new or old untreated wooden surfaces of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer etc complete all as specified and directed.

M&L preparation of new steel surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed.

Demolition Cement concrete (unreinforced) in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work etc complete all as specified and as directed.

Demolition lime concrete of any description and in any position not otherwise specifically provided for etc complete all as specified and as directed.

Supply only water proofing compound ISI marked etc complete all as specified and directed.

The surface shall be painted with one coat of polymeric primer @ 0.40 kg per sqm conforming to IS: 3384 A layer of APP based polymeric membrane. 3mm thick minimum weight 3.5 kg/sqm reinforced with polyester non -woven fabric (weighing not less than 150 gm/sqm) and upper side of membrane thermally insulated with white mineral gravel finish uniformly embedded during manufacturing process shall only used. Side overlap shall be 75 mm and ends shall be 100 mm and all over lap and joints shall sealed by torch application all as specified application of polymeric membrane shall be torch application all as per manufacturer's instructions including providing 40mm thick precast cement concrete (1:2:4) type B0 using 12.5 mm graded stone aggregate in roof covering, benching with WPC and including providing 15 mm thick screed bed or bedding layer of cement mortar (1:4), on roof finished without using extra cement etc complete all as specified and directed.

Dismantling precast concrete or stone slabs in walls, partition walls etc. thickness upto 100mm, including stacking of serviceable material and disposal of unserviceable material within 50 metres lead etc complete all as specified and directed.

M&L for 80-100 mm thick sand stone slabs; set and jointed over joists, walls in CM (1:4) complete including cost of shuttering /scaffolding /safety measure /use of specified equipment for workers of building required etc complete all as specified and directed.

Cutting holes exceeding 150 sq.cm but not excceding 400 sq.cm into or through brick walls, in cement mortar or cement lime mortar and stone walls built in lime mortar or walls of lime concrete and making good in cement mortar (1:3) or cement concrete (1:2:4) type B-1 as required etc complete all as specified and directed.

S&F rolled mild steel joints, channel, angle, or tee sections, fixed independently, without connecting plates, etc.(cut to ordinary lengths i.e. within 20 mm of the length indicated) Fe - 410-W (Gde-E-250) quality B etc complete all as specified and directed.

S & F rolled mild steel rolled sections as in main and cross beams ; hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors ; fixed with angle cleats or other connecting plates (Fe - 410-W (Gde-E-250) etc complete all as specified and directed.

S&F MS chromium plated grating 125mm dia of weight not less than 50gm for floor trap / Nahani trap including taking out old grating of any description or size etc complete all as specified and as directed.

M&L in repair of cast iron nahani trap of 75mm bore, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) etc complete all as specified and as directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors etc complete all as specified & directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors etc complete all as specified & directed.

Demolition Cement concrete (unreinforced ) concrete of any description and in any position not otherwise specifically provided for etc complete all as specified & directed.

M&L 50 mm thick plain cement concrete type C-1 (1:3:6) using 20mm graded stone aggregates as in plinth protections finished even and fair with joints 10mm wide etc complete all as per specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc),or insulation boards / slabs / blankets, any thickness, including cover fillets etc complete all as per specified and directed.

Dismantling posts or struts (wood, steel or R.C.C) any section, including taking out embedded portion and making good disturbed ground posts embedded in concrete, brick work, masonry, etc. complete all as directed by Engineer-in-Charge.

Excavating in post holes ( or similar holes ) each not exceeding 0.5 Cum , getting out, returning, filling in and ramming earth or broken rubble mixed with earth around , in layers not exceeding 25 cm watering , removing surplus soil to a distance not exceeding 50m and making good surface etc. complete all as directed by Engineer-in-Charge.

S&F anodized snap grid frame work of size 605mm x 605 mm for false ceiling including necessary notching. The snap grid shall consist of anodized aluminium main & cross tee of size 36.5 x 25 x 1.4 mm weighing 0.24 Kg/RM and 23.5 x 26.4 x 1.40 mm weighing 0.191 Kg/RM respectively. The main and cross tee shall be jointed at junction crossing with anodized aluminum angle bracket of size 15mm x 15mm x 1.5 mm weighing 0.12 Kg/RM fixed with suitable MS bolts, nuts and washer. The snap grid (main/cross tee section) shall be supported at ends all along the wall with anodized aluminum angle of size 40 x 25 x 2 mm weighing 0.36 Kg/RM fixed to wall with suitable arrangement and providing 12 mm thick mineral fibre board of make Armstrong in fixed in grid support with 2.50 mm dia plain mild steel wire galvanised class 3 fixed in detached works etc to support snap grid, made of aluminum as per specification etc complete all as directed by Engineer-in-Charge. Make: Suspension metal system - MICRO LOOK (design grid) (15 mm grid 8mm return) SILHOUETTE XL 15mm (Nominal) of make Armstrong or equivalent as mentioned in Appx ‘B’ Make: Ceiling tiles - ORCAL extra micro perforation tiles of make Armstrong or equivalent as mentioned in Appx ‘B’

S&F rolled mild steel hollow section square, round or rectangular of required wall thickness , work as in roof trusses (framed), trussed, purlins, crane gantries, post, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections, MS pipe) including distance pieces, cleats etc. conforming to Fe-410W Gde E-250 quality 'A' etc complete all as specified & directed.

S&F Mild steel screw bolts (machine made ) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exceeding 5 cm long (diameter of neck 5 to 10 mm) etc complete all as specified & directed.

S&F Plates ( Plain or chequered ) channels, square cut or notched (ordinary and counter sunk ) forming holes, without any attachment S & F rolled mild steel Fe - 410-W (Gde-E-250) quality "A" etc complete all as specified & directed.

M&L cement concrete type C2, (1:3:6), using 40 mm graded aggregate in foundations, filling and mass- concrete etc. complete all as directed by Engineer-in-Charge.

S&F Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified & directed.

De-vegetation from the bldgs by chemical injection of Round Up (arsenic base) compound and subsequently uprooting of small tree/plant by physical means without damaging the historic fabric and structure of the building under strict supervision of conservation Eng-in-charge.

M&L for 6mm thick asbestos cement corrugated or semi -corrugated sheets in roof wall etc fixed with L-type or J-type or cranked hook bolts etc complete all as specified & directed.

Stitching of cracks in brick masonry using surkhi and lime mortar1:1 (1 lime: 1 Surkhi) matching/ toothing with traditional lime mortar and bricks as existing size and type joinery courses in the vintage structure after raking, cleaning and washing the cracks including all leads, lifts and carriage etc complete all as specified & directed by Engineer-in-charge.

M&L for drilling hole in RCC/Bricks structures using drilling machine up to a depth of 50 mm and 15 mm dia, with the gap of 600mm removing dust, etc by vacuum cleaner and blowers, providing and fixing of heavy grade GI pipe nipple 15 mm dia, 50 mm long, @ 1.0 metre c/c in both direction and injection cement slurry mixed with liquid integral waterproofing additive/1000L for masonary conforming to EN 934-2 T9 confirms to IS 2645-2003. having specific gravity 1.1-1.2 gms/cc, chloride content: Nil as per IS 2645-2003 in combination with expanding powered or dual shrinkage compensating non shrink free flow plasticized grouts conforming to the requirements of BS EN 1504-3 class R4. etc complete all as specified & directed by Engineer-in-charge. Make: Thermax/chemco system/webac chemicals. Note: This item shall be undertaken by the authorized rep of manufacturer.

On dilapidated girders or reinforcement encased in concrete or exposed surface M&L for providing and applying of alkaline based Anti oxidizing compound for steel structure conforming to ASTM D 1748-10(2015) after cleaning to loose scale or oxidized chips from bars. Having specific gravity 1.2 to 1.22 and the material to be applied to the rusted metal using brush, allow it to react for 16 to 324 hour and afterwards wire brushing the surface. Clean with dry cloth before application of protective coating etc complete all as specified & directed by Engineer-in-charge. Make: Thermax/chemco system/webac chemicals. Note: This item shall be undertaken by the authorized rep of manufacturer.

M&L for providing 25 mm thick one component chloride free thyrotrophic fibre reinforced polymer modified repair mortar BS-5F complies with ASTM C 109 with flexural strength ASTM C 348 @ 7 days meeting 7N/mm2 and tensile strength @ 7 days (ASTM C 307) >3 N/mm2 at the outer or inner Brick or stone walls in cement mortar in the ratio 1:4 mixed with styrene butydiene polymerized cement mortar modifier or AR for bonding with cement mortar specially adhered to BS 6319 having specific gravity of 1.025 to 1.04, minimum 43% solid contents) not less than 2% by weight of cement and as per manufacturer,s instructions. for external or internal surface of RCC /slab /beam /columns/facias/any brick or stone wall surface etc. top surfaces of the plaster shall be finished even and smooth with using extra cement including taking down of old cement plaster and dispose of to a distance to 50 m. etc complete all as specified and as directed. Make: Thermax/chemco system/webac or equivalent chemicals. Note:- This item shall be undertaken by the authorized rep of manufacturer.

M &L for curing of the surface using Maxcure CC 75 curing efficiency, Maxcure CC 75 complies with the internationally recognized ASTM C309-90 standards including all tools and tackles. etc complete all as specified and as directed. Make: Thermax/chemco system/webac or equivalent chemicals. Note:- This item shall be undertaken by the authorized rep of manufacturer.

M & L for applying a waterproofing agent with holding the quality of negative hydrostatic pressure on new plastered surface also meeting the elasticity modules as follows 28 days 14000-16000 N/mm2 adhesion to substrate 1 day 0.6N/mm2 28 days 1.3 N/mm2 compressive strength 1 day 12N/mm2 28 days 36N/mm2 flexural strength 1 day 3.6N/mm2 28 days 8.2 N/mm2, modified with special additives and ready to use. Mixed with water ,it cures forming a coating , with limited thickness which resists the penetration of water to achieve compressive strength of 36 N/mm2 in 3 days, adhesion bond strength of 8.2 N/mm2. Coating to be applied after proper surface preparation to remove loose dust , dirt etc. Cleaning, mixing using slow speed electric drill and application of 2 coats etc complete all as specified and as directed. Make: Thermax/chemco system/webac or equivalent chemicals. Note:- This item shall be undertaken by the authorized rep of manufacturer.

Taking down carefully surface aluminium or copper point wiring with PVC casing capping or conduit (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling rose, regulators, sockets, light fittings etc and making good disturbed surfaces etc complete all as specified & directed.

M&L point wiring complete with 1.5 Sq.mm 02 x single core multistranded copper conductor of 1100 volts grade PVC pre insulated FRLS and unsheathed cable enclosed in rigid PVC conduit pipe heavy duty with all PVC accessories such as Tee, bend, collar, elbow, square junction box etc fixed on the concealed surface of wall/ceiling by means of PVC sleeve/dash fasteners with cadmium plated screws including suitable size of PVC boards/ existing sunken box for mounting fittings like switches, sockets, fan regulator etc including 1.5 Sqmm insulated but unsheathed copper earth continuity conductor to common earth and connected to earth dolly complete all as specified and directed for the following :- Note:- Cost of cutting of chases in stone masonry and making good disturbed surfaces for concealing the conduit shall deemed to be included in quoted rate of point wiring.

(a) One light point controlled by one switch.

(b) One fan point controlled by one switch.

(c) One socket outlet 6 amp controlled by one switch on the same board with other switches.

(d) One socket outlet 6 amp controlled by one switch on independent board.

(e) One bell point controlled by one bell/buzzer push.

All as per item No 84 above but with multi stranded copper conductor cable 2.5 Sqmm size for 3 pin 16 Amps socket point outlet on independent board including 2.5 Sqmm copper cable PVC insulated FRLS unsheathed copper continuous earth wire including connecting to common earth dolly complete all as specified and directed. Note:- Cost of cutting of chases in stone masonry and making good disturbed surfaces for concealing the conduit shall be deemed included in quoted rate of point wiring.

S&F switch socket combination 2 in 1, 6 Amps multi-purpose flush type 230 volts etc complete all as specified & directed.

S&F switch socket combination 2 in 1, 16 Amp flush type multi-purpose 230 volts etc complete all as specified & directed.

S&F switch piano flush button single pole one way 6 Amps 230 Volt grade etc complete all as specified & directed.

S&F ceiling rose surface bakelite 50 x 40 mm three terminal ISI marked including suitable size of PVC board etc complete all as specified & directed.

M&L buzzer/ding dong AC 230 volts etc complete all as specified & directed.

S&F ceiling fan of 1200 mm sweep with Five star rating, BLDC 26 W motor etc complete all as specified & directed. Make: Model No- Efficiencia Neo of Havells or equivalent in Crompton/Bajaj/Usha.

S&F step type electronic fan regulator EME type 450 watts etc complete all as specified & directed.

S&F sheet metal enclosure of single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of SP 20 Amps, 240 volts etc complete all as specified & directed.

M&L submain wiring complete with 6 Sq.mm single core multi standard PVC insulated and sheathed cable FRLS copper conductor two runs and one run of 6 Sq.mm copper cable for earth continuity conductor in and including drawn through PVC conduit with all PVC accessories fixed on wall, floor/ceiling etc. complete all as specified & directed.

S & F MCB distribution board powder coated , CRCA steel sheet, degree of protection IP 43-IK 09 with reversible double door, recess mounted having insulated 200 Amps tinned copper bus bar, neutral busbar, earth bar detachable gland plate interconnection earthing connection , blanking plates in unused spaces including connections of wires in MCBs/RCCBs/RCBOs/MCCBs with suitable size lugs of copper materials. DBs shall be fixed on wall in flush pattern by chase cutting in stone or brick wall and disturbed surfaces shall be made good even and smooth using CM (1:3) as required with following ratings & ways:-

(a) 8 way V-TPN with busbar 415 volts

(b) 8 way SPN with 200 amps rated busbar 240 volts

S&F MCBs/MCCB of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB/MCCB DBs of following ratings:-

(a) MCCB TPN 63 Amps 415 volt

(b) MCB SP 240 volts 10-32 Amps

(c) MCB SPN 40 Amps, 240 volt

(d) MCB SP 240 volts 40 Amps

S&F steel tubes 80 mm bore light grade ISI marked with medium grade fittings for cable protection as required complete all as specified & directed.

S&F LED 20 watt LED tube light fitting retro fit type with replaceable rod complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz, etc complete all as specified and directed

S&F white powder coated CRCA housing with LEDs 36 W, 230 V, 50 Hz recess mounting LED 2 feet x 2 feet luminaries, Swam less front frame with flat white hight transmission acrylic cover complete with all accessories including connecting up with twin core twisted flexible copper conductor cable with suitable size etc complete all as specified and directed.

Supply and laying or fixing on wall or passing through pipe testing and commissioning 1100 volts grade ISI marked XLPE insulated and PVC sheathed steel tape / wire armoured underground stranded aluminium conductor cable of size 25 sq mm 4 core etc complete all as specified & directed.

S&F exhaust fan of 380 mm 1400 rpm 230 Volt complete with louver and connecting wire size 0.75 sqmm 2 core upto ceiling rose complete. Make: Model:Turbo Force SP of Havells or equivalent as mentioned in Appx’B’

Material and labour for cutting suitable holes in existing masonary wall and fixing suitable size hume pipe for fixing of exhaust fan 380 mm and making good disturbed surfaces with cement mortar (1:4) and finished to match eisting surface complete all as specified and as directed by Engineer-in-Charge.

Earthing complete with galvanised steel earth plate electrode 600 mm x 600 mm x 6mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level. connecting to the GI wire 4 mm dia by means of bolls, nuts, check nuts and washers of galvanised iron and earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM weight not less than 4 Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and handle of 6mm dia MS bar made to shape, GI medium grade 20mm bore pipe for watering , perforated at bottom. 1.75 metre long placed on top edge of earth plate. Charcoal and common salt filling with fixing arrangement, funnel wire mesh and earth work in soft soil returing filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate 3 of SSR-2009 Part-I and connecting to earth test point all as specified or indicated including testing on completion

Excavating in trenches, not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth; for poles stays, cable etc not exceeding 10 sqm on plan and not exceeding 1.5 metre in depth and getting out in hard/dense soil.

Removing excavated material exceeding 50 metres but not exceeding 250 metres and depositing where directed at a level n exc. 1.5 m above the starting point.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm etc complete all as specified & directed.

Boring of holes under road, pavement, hard standing by trenchless technology and necessary machine for laying underground pipe upto 150mm dia etc complete all as specified and directed by Engineer-in-Charge. Note:- GI pipe shall be measured and paid in separately.

Supply & spread unwashed dry river sand for sand cushioning and covering the underground cable in trenches etc complete all as specified and directed by Engineer-in-Charge. Note :- Punning thickness shall be measured.

M&L for brick protection with sub Class`B` bricks old size laid dry, flat over cable perpendicular across the cable in trenches complete all as directed.

Schedule of Credit

M/s Kartar Singh Construction Co.

Pioneer Enterprises

PD GUPTA AND COMPANY