Repair and renovation of House No. 23 and 24 Type-II New Campus at MAMC Agroha

Amount

Civil Work Items Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. HSR 5.7 5.7.4 In cement mortar

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. HSR 5.23 5.23.2 Nominal concrete 1:2:4 or leaner mix (i/c equivalent design mix)

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : HSR 5.29 5.29.1 Of area 3 sq. metres and below

5.29.2 Of area beyond 3 sq. metres

Dismantling cement conglomerate / terrazzo floors 25 mm to 50 mm manually/ by mechanical means and disposal of material within standard lead as per direction of Engineer- in-charge. HSR 5.42

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. HSR 5.43 5.43.1 For thickness of tiles 10 mm to 25 mm

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. HSR 5.45

Removing rolling shutters including top cover, brackets and side guides etc.complete.HSR 5.41

Centering and shuttering including strutting, propping etc. and removal of form for HSR 6.30 6.30.4 Shelves (Cast in situ)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). HSR:6.16

Providing and laying of conglomerate floor 50mm thick cement concrete topping 1:2:4 HSR:10.7

Brick work with common burnt clay non-modular bricks of class designation 7.5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : HSR 7.22 7.22.2 Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay non-modular bricks of class designation 7.5 in superstructure above plinth level up to floor IV level. HSR 7.28 7.28.2 Cement mortar 1:4 (1 cement :4 coarse sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : HSR 11.6 11.6.2 1:6 (1 cement: 6 fine sand)

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 10.50 10.50.1 Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. HSR:10.63 10.63.4 Size of Tile 1000x1000 mm

Regarding terracing of mud phaska covered with tiles or brick, in cement mortar by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud phaska to proper slope, relaying mud plaster gobri leaping and tiles or bricks, grouted in cement mortar 1:3 (1 cement : 3 fine sand), including replacing unserviceable tiles or bricks with new ones and disposal of unserviceable material to the dumping ground (the cost of the new tiles or brick excluded), all complete as per direction of Engineer-in-Charge. HSR 30.9

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : HSR 9.17 9.17.1 In 75x75 mm deep chase

CEMENT PLASTER (IN COARSE SAND) 12 mm cement plaster of mix :HSR 11.8 11.8.1 1:4 (1 cement: 4 coarse sand)

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 2.0 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 2.00 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: HSR:13.3 13.3.1 Profile B 13.3.1.1 Fixing with adjustable lugs with split end tail to each jamb

Profile E HSR:13.3.3 13.3.3.1 Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. HSR 10.62

Providing & laying average 6mm thick POP Coating on walls, Ceiling, beams and lintels etc. complete in all respects as approved by the Engineer-In-Charge. HSR:11.57

Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : HSR:12.32 12.32.1 35 mm thick shutters 12.32.1.1 with ISI marked M.S. pressed butt hinges bright finished of required size 12.32.1.1.1 Second class teak wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. HSR:12.36 12.36.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete HSR 11.58

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : HSR 11.67 11.67.1 Water thinnable cement primer

Providing and laying 50mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over (BIS 15658:2006) and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. HSR 10.75

Finishing walls with Acrylic Smooth exterior paint of required shade : HSR 11.95 11.95.1 New work (Two or more coat applied @ 1.67 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. HSR:12.10 12.10.1 Second class teak wood 12.10.1.2 30 mm thick

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. HSR:12.12 12.12.2 1.0 mm thick

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. HSR:10.60

Applying pink primer or aluminium priming coat on wood work including preparation of surface, Knotting and stopping etc. HSR:11.77

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. HSR:11.78

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. HSR 5.23 5.23.1 Nominal concrete 1:1.5:3 or richer mix (i/c equivalent design mix)

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : HSR:12.49 12.49.2 25 mm dia (heavy type)

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete. HSR:12.73 12.73.1 125x64x1.90 mm

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : HSR:12.9 12.9.7 Float glass panes 12.9.7.2 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).

Providing & fixing of cuboard 2'-0" deep made up of water proof, terminte treatment WPC 18 mm thick board MIN DENSITY OF 650 KG/CUM of Reputed Brands for sides, top, bottom & horizontal & vertical shelves of box cupboard complete as per drawings. The front openable shutters shall be 25 mm thick WPC and its outer face covered with 1.0 mm laminate of approved colour and makes. The exposed edge of shutter & shelves shall be covered with edge binding tape matching with laminate colour. The shutter shall be fixed to the cupboard box with S.S. continous hinges 3/4"x3/4". The item shall include all accessories steel handle 150mm, steel tower bolts 150mm, curtain rod, hanging rods, cupboard lock and 40mmx40mm (6 No.) S.S. studs etc. complete in all respects as per drawing/direction of Engineer-in-charge (only front area of the cupboard shall be measured for payment) NS

Providing & fixing kitchen accessory cutlery SS including channel and necessary screws complete in all respect. NS

Providing & fixing kitchen accessory basket SS including channel and necessary screws complete in all respect. NS

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete : HSR:12.76 12.76.1 125x85x5.5 mm (heavy type)

100x85x5.5 mm (heavy type) HSR:12.76.3

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : HSR:12.78 12.78.1 250x10 mm

150x10 mm HSR:12.78.3

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. HSR:12.80

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. HSR:12.83 12.83.2 50 mm

Providing and fixing bright finished brass handles with screws etc. complete: HSR:12.85 12.85.1 125 mm

100 mm HSR:12.85.2

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. HSR:12.86

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. HSR:12.87 12.87.1 Triple strip vertical type

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight up to 35 kg and door width up to 700 mm), with necessary accessories and screws etc. complete. HSR:12.88

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : HSR:12.98 12.98.1 300x16 mm

Public Health Work Items Dismantling disjointing, removal and carriage to stores, G.I. pipelines, specials, valves and fittings.20.50 20.50.1 15 mm internal diametre of the pipeline

20.50.2 20 mm internal diametre of the pipeline

20.50.3 25 mm internal diametre of the pipeline

Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead : HSR 5.54 5.54.2 100 mm dia pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. HSR 22.86 Concealed work, including cutting chases and making good the walls etc. 22.86.2 20 mm nominal outer dia Pipes

22.86.3 25 mm nominal outer dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.22.88 22.88.1 15 mm nominal outer dia Pipes

Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. HSR 9.57 9.57.2 110 mm diameter

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- HSR:22.2 22.2.1 White vitreous chinaware Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing white vitreous chinaware pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.HSR: 22.5

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : HSR:22.10 22.10.2 Kitchen sink without drain board 22.10.2.2 610x460 mm bowl depth 200 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. HSR:22.14 22.14.2 Flexible pipe 22.14.2.1 32mm dia

Providing and fixing 100 mm sand cast Iron grating for gully trap. HSR:22.19

Providing and fixing white vitreous chinaware pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : HSR:22.23 22.23.1 W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube up to 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge. HSR:22.38

Providing and fixing toilet paper holder : HSR:22.42 22.42.1 C.P. brass

Cutting holes up to 30x30 cm in walls including making good the same: HSR:22.82 22.82.1 With common burnt clay non-modular bricks

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete HSR:22.92 22.92.1 25 to 40mm niminal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : HSR:22.94 22.94.1 15mm nominal bore

Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : HSR:22.100 22.100.2 20mm nominal bore

Providing and fixing Unplasticised PVC connection pipe with brass unions : HSR:22.101 22.101.2 45cm length 22.101.2.1 15 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet:150 mm diameter. (HSR- 22.102.2)

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : HSR:22.104 22.104.1 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. HSR 22.106 22.106.1 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore . (HSR--22.107.1)

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 HSR:22.108 22.108.1 15mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. HSR:22.109

Supplying and fixing C.I. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5 kg HSR:22.202

Supplying and fixing C.I. cover without frame for manholes : HSR:22.200 22.200.1 455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. HSR:22.209

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. HSR:22.211

Providing and fixing in position best Indian make C.P. brass Tooth Brush cum Tooth Paste Holder fixed in with rawl plugs with C.P. brass screws complete including cutting and making good the walls etc. HSR:22.213 22.213.2 Toothbrush Holder

Providing and fixing in position best Indian make (to the approval of the engineer-in-charge) storage type automatic electric water heater, pressure/non-pressure type thermostatically controlled, suitable for operation on 230 volts, 50 cycles single phase vertical wall mounting fitted with-draw able and adjustable type AC, thermostat. Thermostat knob to be readily accessible through the opening of suitable cover for and adjustment of temperature in the installed position of heater and the thermostat should be withdrawn without having to drain the water, electric heating element made out of copper tube (heating element should be easily removed and replaced in the installed position of heater) A neon indicator 1 AMP, inner container made out of copper tinned both from inside and outside, outer container made out of mild steel sheet finished in gleaming white stove enamel paint, insulated between the inner and outer with fibre glass wool with 1 metre length of suitable capacity 3 core flexible cord with plug and non return valve plastic/lead connections or pressure release valve (where required). Complete including fixing and testing for a week (as required by Engineer-in-charge. HSR:22.216 22.216.1 25 Litres capacity

Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. HSR:22.222 22.222.2 Single Socket Type B 22.222.2.2 110mm o/d SWR UPVC pipe lines laid complete

Providing & fixing 110mm door Tee NS

Providing & fixing 110mm elbow NS

Providing & fixing 110mm Y tee NS

Providing & fixing 110mm coupler/socket NS

Providing & fixing 110mm P trap NS

Providing & fixing CP lock jali complete in all respects (N.S.)

Supply & fixing of Towel Rack 600MM long with lower hangers of stainless steel (N.S.)

Supply & fixing of Towel Ring round with round flange (N.S.)

Electrical Work Items Supply, erection, testing of celling fans ISI marked ( as per IS code 374) with satabile GI pipe complete in all respectes complete as per deration of engginering incharge HSR 20.71 HSR 20.71.1 48" (1200mm)

Supply, erection, testing of exhust fan ( as per IS code 374) having a capacity of 45 cubic meter per minute coplete with sutabile GI sheet duting in structre confirming to letest IS speciflcation complete in all respect to satisfaction of engginering incharge

Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in PVC Conduit etc as required. HSR 23.3.6 23.3.6.1 1 run of Size 1.50 Sqmm(1/1.40mm)

23.3.6.2 1 run of Size 2.50 Sqmm(1.1.80mm)

23.3.6.6 2 run of Size 1.50 Sqmm(1/1.40mm)

23.3.6.7 2 run of Size 2.50 Sqmm(1.1.80mm)

23.3.6.8 2 run of Size 4 Sqmm(1/2.24mm)

Wiring for Light/Fan/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe. HSR 23.4.1 23.4.1.1 Group A

Wiring for Twin control light point with 2 nos , 2-ways, 5 amp. Modular switch GI box and modular face plate in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe. HSR 23.4.2 23.4.2.1 Group A

Wiring for Light/Fan/call bell point in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe, without separate control switch HSR 23.4.3 23.4.3.1 Group A

Wiring in PVC conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box ,modular face plate etc complete as required HSR 23.4.4 23.4.4.1 Group A

Wiring in PVC conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box , modular face plate etc complete as required HSR 23.4.5 23.4.5.1 Group A

Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. HSR 23.5.6 23.5.6.1 1 run of size 1.50 sqmm (1/1.40mm)

23.5.6.2 1 run of size 2.50sqmm (1.1.80mm)

23.5.6.3 1 run of size 4 sqmm (1/2.24mm)

23.5.6.4 1 run of size 6 sqmm (1/2.80mm)

Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. HSR 23.7.6 23.7.6.1 PVC pipe of 20 mm dia.

23.7.6.2 PVC pipe of 25 mm dia.

23.7.6.3 PVC pipe of 32 mm dia.

Supply and Fixing Bakelite sheet on existing MS/GI/wooden/PVC box etc including fixing with brass screws and washers. HSR 23.8.2 23.8.2.2 3mm thick

Supply and erection of suitable MS/GI Box covered with 5 mm thick Bakelite 0 sheet as below HSR 23.8.3 23.8.3.1 75 mm x 75 mm x 60 mm deep M.S. box

Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. HSR 23.8.10 23.8.10.1 1 & 2 Modules including combined plate for Telephone and data

23.8.10.2 3 modules

23.8.10.4 6 modules

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. HSR 23.8.11 23.8.11.1 5 amp 1 way switch

23.8.11.3 15 amp 1 way switch

23.8.11.4 5 amp Socket

23.8.11.5 15 amp 6 pin Socket

23.8.11.6 Bell Push

23.8.11.7 step type Fan Regulator 2 modules 300 watt

23.8.11.8 Telephone Socket outlet modular type

23.8.11.9 TV Socket outlet modular type

23.8.11.10 Blanking plate

23.8.11.11 RJ 45 computer data socket outlet for CAT 6 or CAT 6e cable modular type

23.8.11.13 32A D.P. Main Switch With Key Ring Tag 2 Module ( For Guest room or similar use only )

Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. HSR 23.22.1 23.22.1.3 Triple pole MCCB 16 to 100 amp 25KA

Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- HSR 23.22.5 23.22.5.1 6 amp. to 32 amp Single Pole

Supply and laying of multicore telephone cable conductor size 0.51 mm bright annealed copper conductor PVC insulated and sealed in existing pipe/channel and making necessary connection complete in all respect up to the entire satisfaction of the Engineer-in charge of the work. HSR 23.23.8 23.23.8.1 2 pair telephone wire

23.23.8.2 4 pair telephone wire

Supplying and drawing of 1 no UTP 4 pair CAT 6 LAN Cable in the existing surface/recess MS/PVC conduit as required HSR 23.23.9

Supplying and drawing of 1 no UTP 4 pair CAT 6a LAN Cable in the existing surface/recess MS/PVC conduit as required HSR 23.23.10

Dismantling old wiring points ( surface wiring system ) including necessary repairs to wall etc. HSR 23.25.1 23.25.1.1 Light, fan or call bell Point including circuit/sub main wiring

23.25.1.2 Wall socket point including circuit/submain wiring

Earthing with G.I. earth plate 600 mmx 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required. HSR 24.1.3

Extra for charcoal or coke and salt for G.I. plate or copper plate earth electrode. HSR 24.1.5

Supplying and laying 25mm x 3 mm G.I. strip in 40 mm dia,GI pipe as/from earth electrode including soldering etc. as required.HSR 24.1.7

Supplying and laying 6 S.W.G G.I. wire at 0.50 m below ground level from earth electrode including thimbles, soldering etc. as required HSR 24.1.12

Supply and erection of copper lugs including crimping etc. entire satisfaction of Engineer-in- Charge of the work. HSR 24.2.6 24.2.6.1 1.5 Sqmm

S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. HSR 24.5.2 25.5.2. DWC/HDPE pipe 50/40 mm outer dia/ inner dia

S/E testing and commissioning of cubical type, dust and verman proof wall mounting LT panel made out of 20G M.S. sheet painted with strong synthetic light gray enamal paint suitable for operation on 3 phase 4 wire 50 cycles 400/440 volts A.C. supply including the cost of the following items N.S. 1 INCOMING:- space for accomdating 1 no. MCCB of 200amp. Three pole complete with siutable size of cable chamber to receive incoming cable in sheet steel cubical. Neutral Link A set of LED lamps (3 nos.) phase indicating light OUTGOING: L.T. oannel should be having sufficeint spce for accomodating the following switches/ M.S.B.'s including the cost of the MCB and metering system as required. The panel should be completed with all inter wiring with PVC copper wire and testing etc. complete the job in all respect upto the entire satisfaction of Engineer In-charge of the work

S/E/I/T/C of out door light fixture including the cost of 12 watt LED blub and outer iron frame complete with all fixing acceseries as reqiored upto the entire satisfaction of the Engineer In-charge of the work. Make - Crompton/Philips/Havells /Lumilux(NS 10)

Supply and erection of following light fixture complete with all fixing accesaries as required S/E/I/T/C 1x10 W LED fall ceiling panel light 6000K Make - Philips/Havells/Crompton /Lumilux(NS 11)

Supply and erection of underground cable loose in existing pipe or trenches complete with necessary connections Make- Havells, KEI, RR 35sqmm 4 core cable Armoured (NS-16)

Supply, Installation, Testing and commissioning of telephone junction box (DP box) with 20 pair module all complete connections as per required to complete the job in all respect upto the enter satisfction of Engineer In-charge of the work (NS-17)

Pawan Kumar Contractor

Sh. Sunder Lal Sharma Contractor