SPL REP TO BLDG NO BK-03 OTM 551 RKT REGT,UPGRADATION OF DINNING HALL OF 374 COMP ARTY BDE OFFRS MESS AT BLDG NO-107 MALL ROAD,PROVN OF 08XROLLING SHUTTER (MT SHED) REQD FOR PROVN IN BLDG NO EM-101,EM-105,EM-109 AND EM-112 AT CAMEL LINE AT NASIRABAD

Amount

Taking down cement or cement lime plaster on stone/brick wall, ceiling incl. Raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M& L for rendering in cement mortar (1:6), 15mm thick on stone masonary surfaces finished fair and even and smooth without using extra cement complete all as specified and directed

M&L for rendering 15mm thick in CM 1:4 on stone masonry, external surfaces finished fair & even without using extra cement complete all as specified and directed

M&L for rough cast plaster over 10mm thick cement plaster in cement mortar 1:4 on stone / brick masonary wall surfaces complete all as specified and directed.

M & L preparation new decorated surfaces of walls and providing two coat of cement base paint over a coat of primer complete all as specified and directed.

M & L for complete removal of existing treatment and preparation wall surfaces and applying two coats of oil bound distemper over 1 mm thick wall care of putty over a coat of primer complete all as specified and directed

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper over 1 mm thick wall care putty complete all as specified and directed

Demolition of cement concrete (unreinforeced) in floors and paving n.exc 15cm thickness (above or below ground level) complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C2 using (40 mm graded crushed stone aggregate) as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3) complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and n.exc 4.00 Sqm each and removing from site complete and making good disturbed surfaces of wall in CM (1:3) complete all as specified and directed.

Blank

Taking down unserviceable chowkhats or frame with shutters(without taking off shuters from the frames) of any description exc 1.50Sqm but n.exc 4.00 sqmm and removing from site and making good disturbed surfaces of wall in CM 1:3 complete all as specified & directed. (For windows and ventilators)

S&F 165x60mm size of pressed steel frame for door with one or more rebates including necessary fixing lugs, lock striking plates, hinges, hold fast(40x3mm) etc. complete all as specified and directed.

S & F second class HW 35mm thick, factory made, plain framed, paneled shutter (Three panels) with panels of 9mm thick BWP grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive conforming to IS-710. The size of rails & style shall be as per IS-1003 (part-I) kiln seasoned & chemically pressure treated complete all as per specified and directed.

S&F for 2nd class HW 35 mm thick, gauged and skeleton shutters (Three Panels), factory made open rebated and prepare to receive glass, gauge etc (with sash bar), edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. Size of members of shutter shall be as specified in SSR 2009 Part-I, section 8 clause Member shall be kiln seasoned & chemically pressure treated complete all as specified and directed.

S & F Steel window factory made, out of MS hollow section 79mm x 39mmx1.6mm thick frame with double shutter (glazed & wiregauged shutters) made out of Z section using flush butt welding and tennon riveting all as per IS 1038/83, dobby hinges shall be provided to both shutters, Locking arrangements as per sample approval by GE, provided with knob, 10mm MS square bars in grill, Z section handle 100mm size and 150mm long hook & eye welded to frame and shutter, four Nos lugs welded to frame inculding necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4 type B-1 including synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and directed. Note : Wire mesh and sheet glass shall be measured & paid separately under respective items.

S & F Steel ventilator factory made, out of MS hollow section 79mm x 39mmx1.6mm thick frame with double shutter (glazed & wiregauged shutters) made out of Z section using flush butt welding and tennon riveting all as per IS 1038/83, dobby hinges shall be provided to both shutters, Locking arrangements as per sample approval by GE, provided with knob, 10mm MS square bars in grill, Z section handle 100mm size and 150mm long hook & eye welded to frame and shutter, four Nos lugs welded to frame inculding necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4 type B-1 including synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and directed. Note : Wire mesh and sheet glass shall be measured & paid separately under respective items.

S&F for Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour sheet PVC Sheet rinforced with M.S square tube,fixing in opening as per specification & Drawing complete all as specified and directed.

S & F factory made solid pannel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded. sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawings on page 146 of SSR Part - II 2004 complete all as specified and directed.

S & F aluminium handle fabricated type, anodised 150mm size conforming to IS complete all as specified and directed.

S & F 300mm long aluminium alloy, anodised, sliding door bolts with hasps, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolt of extruded section, ISI marked, 150 mm long complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled, ISI marked of size 100 mm, complete all as specified and directed.

S&F stainless steel butt hinges 100mm size complete all as specified and directed.

M & L for preparation of new wooden surface over 10cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface over 10cm width or grith & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as specified & directed.

S&F in repairs fancy type 20mm dia SS curtain rods fixed to bracket complete all as specified & directed.

S&F decorative type knobs with bracket of Stainless Steel fixing at end of curtain rod complete al as specified & directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with wire staples complete all as specified & directed.

S&F 3.00 mm thick sheet glass, ordinary quality & glazing with oil putty not exc 0.50 Sqm each pane complete all as specified and directed.

S & F figured glass pin headed type, 3 mm thick and fixed with oil putty, size of glass n. exc 0.50 sqm in each pane for steel or wooden windows/doors fixed with wooden beadand pin tacked complete all as specified and directed.

Demolition of stone/brick masonry built in cement or cement lime mortar complete all as specified and directed.

M&L for brick work with flyash bricks straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed.

Dismantling floor, hearth or wall tiles, including cement mortar, removing serviceable tiles from site & rubbish off the premises, complete all as specified and directed.

M&L for glazed ceramic coloured tiles 7 to 8 mm thick in vertical surfaces area of each tile of exc. 0.11 Sqm and but not exc. 0.18 Sqm set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 Sqm but not exc 0.18 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding in cement mortar 1:6 complete all as specified and directed

S & F in repairs Squatting pattern Water closet, Orissa pattern of vitreous chinna Size 580x440mm wide with integral foot rest etc complete all as specified and directed.

Supply and Fixing in repairs vitreous china wash down water closet pedestal pattern pan white with trap including connection to existing out joint pipe, flushing pipe or Cistern, antisyphonage pipe, including making, etc complete including making goood to floor etc complete all as specified and as directed.

Supply and Fixing in repair plastic water closet seat cover any colour closed pattern with flat bottom and cover with mild steel chromium plated hinging device etc complete as specified and directed.

S&F in repairs 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F in repairs 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F 75mm bore PVC(SWR) bends with oval access door of any radius complete all as specified and directed.

S & F110mm bore PVC(SWR) bends with oval access door of any radius complete all as specified and directed.

S & F 75mm bore PVC (SWR) junction single, (Single T) equal or unequal with oval access door complete all as specified and directed

S & F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with oval access door complete all as specified and directed

S&F Soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified and directed

Taking down old unserviceable 15mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed.

S&F 15mm bore, water tubing, medium grade, galvanised with all fittings and fixed to walls, ceiling or laid in floors / trenches complete all as specified and directed.

Taking down old unserviceable 20mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed.

S&F 20mm bore, water tubing, medium grade, galvanised with all fittings and fixed to walls, ceiling or laid in floors / trenches complete all as specified and directed.

Refixing 15mm bore old GI tubing to walls, ceiling or laid on floor including necessary cleanig, cutting, screwing and new fittings such as elbow, Tee, union, socket, reducer etc. complete all as specified and directed

Refixing 20mm bore old GI tubing to walls, ceiling or laid on floor including necessary cleanig, cutting, screwing and new fittings such as elbow, Tee, union, socket, reducer etc. complete all as specified and directed

S & F in repairs grating round 125 mm dia PTMT minimum weight 50 gms fixed to Floor trap/Nahni trap with CM 1:6 etc complete all as specified and directed.

S&F in repairs 15mm bore cast copper alloy chromium plated bib tap fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified.

S&F in repairs PVC (SWR) floor trap plain with grating incl jointing with solvent cement of 75mm dia complete all as specified.

S&F in repair tubular towel rail, chromium plated brass 20mm dia 'D' type 60CM long between flanges complete all as specified and directed.

S&F in repair PVC low level flushing cistern syphonic action type white with inlet ball valve, handle including brackets 10 ltrs capacity etc complete all as specified and directed.

S&F in repair CP brass shower rose with or without swivel joints 100mm size including fixing to steel pipe or union complete all as specified and directed.

S & F in repairs PVC connections 15mm size with PTMT nuts and bolts of length 450mm etc complete all as specified and directed

S&F in repair angle valves 15mm bore , cast copper alloy chromium plated fancy type, screwed down high pressure screwed both ends for iron pipe or for unions and fixed etc complete all as specified and directed.

S&F Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed

S&F in repairs gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union 25 mm dia, ISI marked complete all as specified and directed.

S&F in repairs pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipe, 15mm bore fancy type complete all as specified and directed

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified

M & L for 75 mm thick PCC 1:4:8 type D-2, using 40 mm graded stone agg as in sub base etc complete all as specified and directed.

M & L PCC 1:2:4 type B-2, using 40 mm graded stone agg as in surface channel & drain etc complete all as specified and directed.

M&L only on old surfaces mirror polishing on marble/granite/mosaic flooring where ever required to give high gloss finish complete.

M&L for machine cut Kota stone slab flooring 20-25mm thick over and incl 15mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with 25mm thick PCC 1:2:4 using (20mm graded stone aggegate) complete all as specified.

M&L for Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over including cement screed 10mm thick in CM (1:4) & jointed with grey cement slurry mixed with pigment to match the smooth of the slab incl rubbing and polishing complete all as specified and directed.

S&F in repair wash basins vitreous china, white /coloured flat back size 550 x400mm fixed including bracket complete all as specified and directed.

Demolition of re-inforced cement concrete is re-inforced (re-inforced cut as required to facilitate demolition) complete all as specified and directed

Pre-cast re-inforced cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in manhole covers, shelves similar articles including form work complete all as specified

M & L for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

Supply only integral water proofing compound, ISI Marked complete all specified and directed.

Dismantling of existing unserviceable water tank of any description capacity exc 250 Ltr but n.exc 500trs capacity each complete all as specified and directed

S& F rotational moulded synthetic (HDPE) water storage tank 500litre capacity hoisted & fixed in position all as specified in SSR Part-I complete all as specified and directed.

S&F ball valves PTMT high pressure with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe, 20mm bore compete (Minimum weight 210 gm) complete all as specified and directed.

S&F 75 mm bore stack clamps out f 50mm by 5 mm flat iron and 16mm dia rund irn stays, including bolts and nuts and securing ends f stays to wall or roof complete all as specified and directed

S&F 100 mm bore stack clamps out f 50mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed

S&F vitreous china urinal half stall type, white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement fixing automatic flushing cistern with brackets, flusg pipe, grating and union for discharge pipe (exclusive of fixing supply pipee to flushing cistern, trap and waste pipe)

S&F Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete gear operated type with bevel gear box and crank handle complete all as specified and directed

S&F ball bearing for rolling shutters complete all as specified and directed

S&F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed

M&L for PCC 1:2:4 Type B-1 (using 20mm stone crushed agg.) as in fixing of hold fast and other similar work complete all as specified and directed.

M&L for fly ash Brick work old size, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 all as specified and directed..

M&L for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

Blank

M&L for 18 to 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window -cills, cooking platforms and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl rounding of edge laid over and incl 15mm thick screed bed in CM (1:6) including rounding of edges of stone slabs one edge, complete all as specified and directed.

Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows,ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight,mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P.brass/ stainless steel screws, all complete as specified and directed.

Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors,windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paidfor separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as specified and directed.

S&F 5.5mm thick sheet glass ordinary quality and glazing in square, complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed.

Taking down MCB DB's complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm, PVC insulated, unsheathed, stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit 20mm dia or higher complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and sunk type pressed steel anodised terminal box 1.2 mm thick with bakelite laminated sheet top cover 3 mm thick, brass screws and cup washers including 1.5 Sqmm stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories for complete all as specified and directed.:-

All as per item No. 95.00 here-in-before but One light point controlled by one, one way switch.

All as per item No. 95.00 here-in-before but One ceiling fan/exhaust fan point controlled by one, one way switch.

All as per item No. 95.00 here-in-before but One 3/5 pin 5 Amp socket on same board with other switches.

All as per item No. 95.00 here-in-before but One 3 pin 5 Amp socket on independent board.

All as per item No. 95.04 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 2.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth.

S&F switch piano flush type 5 amps, single pole one way 240 volts complete all as specified and directed.

S&F switch piano flush type 15 amps, single pole one way 240 volts complete all as specified and directed.

S&F Socket outlet 3 Pin 5/6 Amp flush type complete all as specified and directed.

S&F socket out let 2 in 1,multipurpose 3 pin 15/16 Amp flush type ISI marked complete all as specified and directed.

S&F ceiling fan regulator electronic flush , steped (four step) 230 Volts AC complete all as specified and directed.

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm complete all as specified and directed.

S&F of lamp holder PVC/polycarbonate type with back plate complete all as specified and directed.

S&F LED tube light fitting in acrylic linear tube (1x 18 watt),230V for single LED tube light including 1 x 18 W LED retrofit bar professional CW 6500 K cover channel, bipin holders,LED power driver, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

S & F LED light fitting 1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

M & L for Submain wiring with two single core PVC insualated, unseathed, FRLS, 1100 volts grade 6 Sqmm multi stranded copper conductor cable drawn through existing concealed conduit incl one run of green colour earth continuity conductor with 6 Sqmm multi stranded copper conductor cable complete all as specified and directed. Make of wire- Polycab/KEI/Havells Note : - Two run of single core cable, one run of earth continuity conductor shall be measured as one unit length.

Supply and fixing testing and commissioning energy saving street light luminaire 25 watt LED , pressure die cast housing with epoxy powder coated with colour finish and prismatic poly carbonate coverlic cover complete, IP 66 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by Engr-in-Charge.

Supply and fixing street light bracket made of 32 mm GI pipe , 1.2 mtr lenght fixed with two nos of clamp , nut and bolts for fixing of street light complete all as specified and directed by Engr-in-Charge.

S & F of MCB SP, 240 volt, 6 Amp to 40 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S&F of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed.

S & F of MCB SPN, 240 volt, 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unsv existing earthing .

Disconnecting unserviceable sub main wiring/service connection of any size and including conduit of any type and accessories and removing from site and making good the disturbed surfaces complete all as specified and directed.

S&F of modular switch 1 way 6/10Amp , 1 module, complete all as specified and directed.

S&F of modular switch 1 way 16Amp, 1 module, complete all as specified and directed.

S&F of modular socket 6Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F of modular socket 6Amp/16 Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F box type LED tube light fitting in acrylic linear tube 1x 20 watt, 230V complete with bipin holders,LED power driver, connector block, and LED Tube rod 20 watt.

Supply and fixing in repair recess mounted LED 12 watt Slim, compact, auminum die cast edge lit panel, round fixture with opal diffuser and separate electronic driver in warm white/cold white complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair surface mounted LED downlight 15 watt in warm white or cold white round shaped , Slim surface mounted LED panel with premium diffuser to ensure glare free & even light distribution complete all as specified and directed.

S&F of MCB distribution board triple pole & neutral IP-43 double door metal, 4 way ,415 volt made out of CRCA sheet steel , factory made powder coated with insulated bus bars , shrouded neutral bars, earth bars , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCB's complete all as specified and directed. Make: Legrand/Schneider/Seimens Note: MCB DB and MCB SP/SPN will be of same make.

S & F of MCB SP, 240 volt, 6 Amp to 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F of MCB SPN, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

Supply and fixing of MCB TPN 63 Amp capacity,415 volt , 10 KA , 'C' curve complete all as specified and directed. Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

M & L for submain wiring with two single core PVC insualated, unseathed, FRLS, 1100 volts grade 4 sqmm multi stranded copper conductor cable drawn through and incl 25 mm dia PVC non metallic rigid concealed conduits and the conduits accessories incl one run of green colour earth continuity conductor with 4 sqmm multi stranded copper conductor cable.

S & F in repair single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amp MCB SP `C' series for geyser & AC complete all as specified and directed.

Manu Enterprises

M/S JAGDISH PRASAD AIRUN

M/s Jai Jinendra Constructions

V K LAKWAL CONSTRUCTION

kirtiman traders

TARA CHAND JI GOMA CONSTRUCTIONS CO.

M/S AL ASMA ENTERPRISES