REPAIR MAINT AND IMPROVEMENT TO CERTAIN BR ASSETS EM INSTALLATIONS REPAIR MAINT AND IMPROVEMENT OF EM INSTALLATIONS INCLUDING RENEWAL OF EARTHING AND ALLIED WORKS UNDER GE (EAST) MATHURA

Amount

Taking down cement plaster on brick or stone walls, etc. including racking out joints, hacking for key, scrubbing down with water, etc complete.

M&L rendering 15mm thick (10mm + 5mm) plaster on fair face of brick work in CM 1:4 and surface finished even and fair by mixing liquid water proofing compound as per manufacturers instructions complete. Note :- Liquid WPC shall be measured & paid seprately under relevant item of this BOQ.

M&L for 15mm thick rendering in cement mortar 1:6 on other than fair faces of brick/concrete surfaces finished the surface even and smooth without using extra cement.

M & L for rendering 10 mm thick in CM 1:4 on fair faces of concrete surfaces of ceiling, finishing the surface even & smooth without using extra cement etc. complete all as specified and as directed.

Supply only liquid water proofing compound hydroseal-W+ / Dr Fixit or eqivalent (for plaster hardening, to contol efflorescence & fungal growth) as approved by GE.

M&L for preparation of newly plastered surface of wall and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surface of ceilling and applying three coats of white wash on ceiling surface complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surface of walls and applying two coats of oil bound distemper over a coat of Alkali resistant primer over a coat of cement base wall care putty not less than 1mm thick complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for preparation of old plastered surfaces of wall and applying one coats of cement base paint including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for preperation of old steel surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted wooden surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L for Preparation of old plastered or un plastered distempered surfaces of walls by washing, rubbing down, stopping of distempered or painted surfaces, removing nails and applying one coat of oil bound distemper on wall surfaces complete.

M&L for Preparation of old plastered or un plastered white washed surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soots and efflorescence salts, removing nails and making good and applying one coat of white wash complete.

M&L for preparation of old surfaces of ceilling and applying one coat of white wash complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises.

M&L for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.

M&L for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirtings etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.

M&L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified.

M&L for Glazed ceramic tiles vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick backing coat of cement mortar in 1:4 complete all as specified.

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) incl chequered tiling and Paver blocks

M&L for 50 mm thick PCC M-15 grade (Nominal mix) using 12.5 mm graded stone aggregate as in plinth protection, finishing cement concrete surface even and smooth without using extra cement.

M&L for 75mm thick PCC M-15 grade (Nominal mix) using 20mm graded stone aggregate, finished surface even and smooth without using extra cement, laid in alternate bays & joints filled & finished as specified

M&L for Chequered cement concrete tiles (with white cement and pigment) 20cm x 20cm x 25mm thick rubber moulded glossey finish, set, jointed and pointed in neat cement slurry in floors over including 15mm screed bedding in cement mortar 1:4 complete all as specified and as directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-35 Grade made with grey cement and pigment complete all as specified and directed.

M&L for 100 mm thick cement concrete M-7.5 grade (Nominal mix) using 40mm graded stone aggregate as in sub base complete.

M&L for sand filling under floors incl consolidation etc complete for laying paver blocks.

M&L for PCC M-15 grade (Nominal mix) using 20mm graded stone aggragate as in coping surface channels, benchings etc of manholes finished fair and even.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar.

M&L for 18-20mm thick machine cut machine polished kota stone slab flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15 mm thick screed bed or bedding layer in cement mortar 1:3 complete.

M&L for 18-20mm thick Machine cut Machine polished kota stone slab as in riser of steps, skirting, dado and pillar jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and incl 10mm thick plaster in cement mortar 1:3 complete.

M&L for 20 mm thick Granite slab work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like over and including 20 mm thick screed bed in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite and hole for gas pipe in pre-cast slab as well as stone slab in cooking platform complete all as specified

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

Demolition of brick work or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles.

M&L for Brickwork with fly ash bricks (old size) straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified.

M&L for Brick work with old size fly ash bricks straight or curved on plan to any radius in half brick thick walls in built in CM 1:4.

Dismantling of brick work or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles.

M&L brick work with sub class B brick straight or curved on plan exc 6 m mean radius built in CM 1: 6 complete all as specified but Except brick. Note: Old brick dismanted shall be reused .

Dismantling of 6 mm thick AC corrugated or semi-corrugated sheets in roof covering including ridges, hips, valleys and flashings etc .

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of on colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering fixed with self tapping screws complete.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in cladding to wall, fixed with self tapping screws as specified.

Dismantling timber scantlings 40 sqcm and over in section, in any position in unframed work as specified.

M&L for Mild steel work in tubular trusses purlins, including special shaped washer, angle cleats, fish plates, gusset plates, base/ bearing plates, bolts and nuts etc. complete using ERW or induction butt welded tubes conforming to 1161-1979 grade st 240.

M&L Second class hard-wood timber clean savar fixed in scantlings.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of redoxide primer complete all as specified.

Dismantling wall and ceiling boards (fiber, pulp, insulation, etc) or insulation board/slabs/blankets, any thickness, including cover fillets.

Providing and fixing inter locking metal grid (snap grid for false ceiling) of size 605 mm x 605 mm in true horizontal level, hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24 mm X 38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200 mm x 600 mm and secondary cross “T” of length 600 mm and size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200 mm X 600 mm panel to form grids of 600 mm X 600 mm and wall angle of size 24 mm X 24 mm X 0.4 mm. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 mm X 37 mm X 25 mm X 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 mm X 30 mm X 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications and as directed by Engineer-in-charge. 24 mm X 38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200 mm x 600 mm and secondary cross “T” of length 600 mm and size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200 mm X 600 mm panel to form grids of 600 mm X 600 mm and wall angle of size 24 mm X 24 mm X 0.4 mm. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 mm X 37 mm X 25 mm X 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 mm X 30 mm X 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications and as directed by Engineer-in-charge.

M&L Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions

Taking down chowkhat or frames with shutters without taking off shutters from frame area n.exc 1.50 Sqm each.

Taking down door chowkhat or frames with shutters without taking off shutters from frame area exc 1.5 sqm and n. exc 4 Sqm each.

S & F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded fixed to wall including one shop coat of redoxide primer complete all as specified and directed.

S&F 4 mm thick sheet glass, ordinary quality and glazing fixed to aluminium frame in square exc. 0.5 square metre in each pane complete.

S&F 105x60 mm Pressed steel frames made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with one shop coat of red oxide primer complete, as specified, supplied and fixed all as specified and as directed.

S&F 125x60 mm Pressed steel frames made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with one shop coat of red oxide primer complete, as specified, supplied and fixed all as specified and as directed.

M&L for preparation of new primed surfaces of steel of any description over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified.

M&L for cement concrete M-10 grade (Nominal Mix) using 12.50mm graded aggregate for filling in pressed steel door frames all as directed.

S&F 40 mm thick, Flush shutters, solid core construction, with block board core and plywood face panels, commercial type both face covered with decorative face veneer with lipping/frame to match on both sides complete as specified.

S&F 30 mm thick glazed and skeleton shutters of 2nd class HW, open rebated and prepared to receive glass/gauze etc edges or framing plain chamfered or rounded fitted with cut or mitred beads for securing glass etc as specified in SSR pt-1 section 8.20 (a) all as specified.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification.

S&F Factory made solid panel pace door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

M&L for preparing new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat pink primer complete all as specified and as directed.

S&F in repair 1mm thick Steel rolling shutters, with out ball bearing, as specified including top cover, an?choring rod, hasp and staple and one shop coat of primer; erected in position as indi?cated, complete: push pull or manual type

S&F in repair, Safety lever locks mild steel with 4 levers for rolling shutters

S&F in repair, Ball bearing for rolling shutters

S&F 150 mm Aluminium, anodised, barrel tower bolts of extruded section.

S&F 250 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed with shutters complete all as specified.

S&F 150 mm long aluminium anodised handle fabricated type all as specified and as directed by Engineer-In-Charge.

S&F 100 mm Butt hinges, medium weight, cold rolled mild steel, and fixed.

S&F powder coated (Powder coating shall not be less than 50 micron of approved colour) Aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F Powder coated (Powder coating shall not be less than 50 micron of approved colour) aluminium window and ventilator shutters, side hung/sliding type with or without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box,main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

S&F in repair, Aluminium (Die cast) body Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified.

S&F 5.5 mm thick sheet glass, ordinary quality and glazing fixed to aluminium frame in square exc. 0.5 square metre in each pane complete.

S&F 4mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane

Dismantling fencing wire mesh, any type.

Supply only chain link mild steel galvanized fencing any size or type complete all as specified and directed by Engineer-in-Charge.

Fixing only chain link fencing of description fixed to steel part with mild steel flat & nut bolt etc. (a) Supply only fencing will be measured and paid separately. (b) Supply & fix mild steel nut bolt line wire and flat will be measured and paid separately.

Supply and fix mild steel section for Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts for post and struts for fencing including cutting top to shape as directed drilling hole notching for wire etc.or flat iron fillet (for securing wire mesh etc)including all necessary drilling bolting,using steel section of grade E-165 ( Fe-290)complete.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long & dia of shank 5 mm to 10mm long.

M&L for Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed fixed in repair. Note :- Each line wire shall be measured

S&F in repairs 4 mm thick sheet glass, ordinary quality and glazing to aluminium/ Steel/ wooden frame in square exc. 0.5 square metre in each pane complete.

S&F in repairs 4mm thick frosted glass, ordinary quality and glazing fixed to aluminium frame in square exc. 0.5 square metre in each pane complete.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.

S&F in repairs Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed in repairs with stainless steel wire staples/ screwed complete all as specified.

Taking up or down tubes 15 mm dia galvanized iron and connections and removing/shifting to site/store incl cleaning for relaying/refixing where directed

Supplying & fixing to walls and ceiling 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed

Taking up or down tubes 20 mm dia galvanized iron and connections and removing/shifting to site/store incl cleaning for relaying/refixing where directed

Supplying & fixing to walls and ceiling 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed

S&F 500 liters capacity rotational moulded polyethylene triple layer water storage tank (Cylindrical vertical with close top) hoisted and fixed in position including connections including dismantling existing old water storage tank all as specified.

S&F ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for 15 mm bore dia of pipe and fixed ( Minimum weight 210 gms each)

S&F Gun matel, globe or gate valves 20 mm bore dia, with iron wheel head, screwed both ends for iron pipe and fixed in repairs.

S&F in repairs Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including setting the trap and pan in concrete and including 10 ltr capacity PVC valveless syphonic action type low level flushing cistern and 32mm dia PVC Flush pipe complete including jointing to socket of flushing rim all as specified and as directed.

S&F PVC connection 15mm size with brass nut of 600mm long.

S&F in repairs vitrreous china wash hand basin, white, flat back, size 550x400mm including brackets and a pair of rack bolts, waste fittings, brass, chromium plated 32mm with long screwed shanks and fly nuts, flanged end bedded in red lead cement and other end fixed,PVC waste pipe of 32mm bore 75cm long, complete all as specified and as directed.

S&F in repair stop cock/ value cast copper alloy screwed down with high pressure with crutch or butterfly handle screwed with ends for iron pipe or uinon & fixed of 15 mm dia.

S&F in repair bib taps chromium plated cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe of bore 15mm complete, Make : Hindware/ Cera 1st quality.

Supply and Fixing in replacement of unserviceable battery charger of capacity 12V/24 Volt complete all as specified and directed by Engineer-in-Charge.

Supply and fixing cable tray suitable for supporting and carrying out LT cable upto transformer of size upto 240 sqmm complete all as directed.

Supplying and laying synthetic Rubber insulated mats 2 mm thick for voltage upto 3.3 kv for electrical purpose as per IS 15652-2006, (superseding IS 5424) suitable for electrical shock safety of sizes 2m x 1m.

Supplying and laying synthetic Rubber insulated mats 2.5 mm thick for voltage upto 11 kv for electrical purpose as per IS 15652-2006, (superseding IS 5424) suitable for electrical shock safety of sizes 2x1m.

Supplying and laying synthetic Rubber insulated mats 3.0 mm thick for voltage upto 33 kv for electrical purpose as per IS 15652-2006, (superseding IS 5424) suitable for electrical shock safety of sizes 2x1m.

Supply and fixing in replacement of MCCB 630Amp rating,4-pole 415V, thermal magnetic release with overload and short circuit adjustable type breaking capacity 36 KA complete.

Supply and fixing in replacement of MCCB 400Amp rating,4-pole 415V, adjustable thermal adjustable megnetic type breaking capacity 36 KA complete.

Supply and fixing in replacement of MCCB 250Amp rating,4-pole 415V, adjustable thermal adjustable megnetic type breaking capacity 36KA complete.

Supply and fixing in replacement of MCCB 100Amp rating,4-pole 415V, adjustable thermal adjustable megnetic type adjustable thermal adjustable megnetic type breaking capacity 16KA complete.

Supply and fixing in replacement of MCCB 250Amp rating,3-pole 415V, adjustable thermal adjustable megnetic type breaking capacity 35KA complete.

Supply and fixing in replacement of MCCB 200Amp rating,3-pole 415V, adjustable thermal adjustable megnetic type breaking capacity 35KA complete.

Supply and fixing in replacement of MCCB 160Amp rating,3-pole 415V, adjustable thermal adjustable megnetic type breaking capacity 25KA complete.

Supply and fixing in replacement of MCCB 100Amp rating,3-pole 415V, adjustable thermal adjustable megnetic type breaking capacity 25KA complete.

Supply and fixing in replacement of MCCB 63Amp rating,3-pole 415V, adjustable thermal adjustable megnetic type breaking capacity 16KA complete.

Excavating in trenches n. exc 1.5m wide & n. exc 1.5mm depth for laying of cable and getting out in soft/loose soil complete.

Returning filling with earth obtained from excavation including spreading, watering, levelling and consolidation in layers not exceeding 25cm thick complete.

Removing surplus soil to a distance not exceeding 50 m and depositing at a level not exceeding 1.5 m above the starting point complete.

M&L for sand cushioning to under ground cable in trenches in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable complete all as specified and directed by Engr in charge. Note:- Measurement shall be taken after gentling puning of sand.

Supply and Laying Unreinforced precast concrete cable cover class LV type 1, size 250x150x40mm complete as directed.

S&F Steel tubes light grade galvanised with all fittings fixed to walls/ floors/ poles/ road crossing etc of following sizes complete:-

50 mm bore

80 mm bore

Supplying, laying or fixing or passing through pipe, testing and commissioning XLPE insulated, steel tape / wire armoured heavy duty electric underground cable, 1100 volts grade with stranded aluminium conductor of following nominal cross sectional area :-

95 Sqmm 3.5 core.

120 Sqmm 3.5 core.

150 Sqmm 3.5 core.

185 Sqmm 3.5 core.

240 Sqmm 3.5 core.

300 Sqmm 3.5 core.

Dismantling unserviceable any size of cross arms and anti climbing devices from pole /structures. complete all as specified and directed.

M&L for work confirming to Fe-410-O or Fe-310-O as in cross arms, support, bracings, stiffeners, clamps channels fabricated from structural steel including nuts, bolts and washers welding, bending cold or hot drilling holes for bolts in any shape or size all as directed including two coats of aluminium paint over a coating of red oxide primer all as directed by Engr-In-Charge.

M&L for scraping, scretching, cleaning the old paint, preparation of old steel surface of LT 09 Mtr long steel tubular pole and applying two coat of aluminium paint and writing pole Nos. including applying one coat of cement base paint on PCC muff all as directed by Engr-In-Charge.

M&L for scraping, scretching, cleaning the old paint, preparation of surface of LT 9mtr long PCC pole upto 1.5mtr from ground level and painting Black & White strip 30cm a part alternaterly and applying synthetic enmel paint for writing pole Nos. & applying one coat of cement base paint on PCC muff all as directed by Engr-In-Charge.

M&L for dismantaling of old unserviceable PCC poles/struts any type and size.

Supply & install steel tubular swaged pole type 410 SP -31 (9 Mtr long) complete with CI base plate and finial including foundation with following work: (a). Excavating in post holes (or similar holes) each n.exc 0.5 cum each, getting out in soft/loose soil, returning filling in and well ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm watering and disposal of surplus soil to a distance not exceeding 50 m and making good surface. (b) PCC M-7.5 grade (Nominal mix) using 40 mm graded stone aggregate in base (0.90m x 0.60m x 0.15m height) as in lean concrete. (c) PCC M-10 grade (Nominal mix) using 40 mm graded stone aggregate in foundation filling & mass concrete of size 0.60m x 0.60m x 1.5m height. (d) PCC M-15 grade (Nominal mix) using 20 mm graded stone aggregate as in coping (0.45m x 0.60m 0.45m height) including necessary formwork. (e) M&L for applying two coats of aluminum paint over a coat of red oxide primer and making alternate colour bands of black & yellow colours in 30 cm width upto a height of 1.5 mtr from pole coping with synthetic enamelled paint complete. (f) M&L for applying one coat of bitumenous paint to tubler pole below GL.

Earthing complete with galvanised steel earth plate electrode 60cmX60cmX6.0mm thick, buried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of the plate not than 1.5mtr below normal ground level connected to GI earth strip of size 32x6mm dia by means of bolts, nuts, check nuts and washers of galvanised iron complete earth pit of PCC M-10(Nominal mix) using 20mm graded stone aggregate, 50mm thick earth pit cover of RCC M-15 (Nominal mix) using 20mm graded stone aggregate with TMT reinforcement bar of 8mm dia @ 150mm centre to centre both ways, MS handle 10mm dia made to shape, PGI funnel, wire mesh and 20mm bore GI water pipe medium grade and 40mm bore medium grade GI pipe for protection of earth strip from plate to main switch board, common salt, charcoal dust including testing on completion complete all as specified and as directed all as shown in electrical plate No. 3 including testing on completion and making good the disturbed surfaces of wall floors etc without claiming extra cost complete. Note: GI strip beyond 5.0Mtr length from earth electrode shall be measured and paid separately).

Earthing complete with galvanised steel earth plate electrode 60cmX60cmX6.0mm thick, buried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of the plate not than 1.5mtr below normal ground level connected to GI earth strip of size 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron complete earth pit of PCC M-10(Nominal mix) using 20mm graded stone aggregate, 50mm thick earth pit cover of RCC M-15 (Nominal mix) using 20mm graded stone aggregate with TMT reinforcement bar of 8mm dia @ 150mm centre to centre both ways, MS handle 10mm dia made to shape, PGI funnel, wire mesh and 20mm bore GI water pipe medium grade and 40mm bore medium grade GI pipe for protection of earth strip from plate to main switch board, common salt, charcoal dust including testing on completion complete all as specified and as directed all as shown in electrical plate No. 3 including testing on completion and making good the disturbed surfaces of wall floors etc without claiming extra cost complete. Note: GI strip beyond 5.0Mtr length from earth electrode shall be measured and paid separately).

M&L for GI strip of size 32x6mm as earth continuity conductor burried in ground or drawn in pipe or fixed to wall on saddle complete all as directed by Engineering-in-Charge.

M&L for Copper strip 20x3mm as earth continuity conductor burried in ground or drawn in pipe or fixed to wall on saddle complete all as directed by Engineering-in-Charge..

M&L for earth continuity conductor galvanised iron wire 4 mm dia complete all as directed by Engineering-in-Charge..

Supply and fixing GI funnel complete with wire mesh for earthing water pipe.

M&L for earth pit cover of size 450x450x50mm thick of RCC M-15 (Nominal mix) using 20mm graded stone aggregate with TMT reinforcement bar of 8mm dia @ 150mm centre to centre both ways, MS handle 10mm dia made to shape complete all as specified and as directed

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering /cladding to wall with self tapping screws complete all as directed by Engineering-in-Charge..

M&L for framed work as in MS sheet section,hinges, angle iron etc complete confirming to Fe-410-O or Fe 310-0 all as specified and directed by Engr-in-Charge.

Cutting wild grass, bushes, creaper, unwanted vegetation from inside / surrounding of E/M installations, near transformers, pole structures etc including cutting creapers from barbed / cattle fencing of the installations as when directed and removing of unwanted material from installation compound and depositing where directed. (Note : (a) The item shall be operated maximum three times in entire period of contract in the same installations. (Area measured separately each time).

Labour & tools for trimming tree branches upto 100 mm girth of any location around existing HT/LT OH lines giving clearance of 1.5 m on all sides complete. Note:- Trimming of tree branches irrespective in numbers in each tree shall be measured as one unit.

M&L for painting of LT panel after scrubing the existing paint and apply of two coats of existing synthetic enamel paint oer a coat of red oxide primer including repair/replacing pitted portion not excluding 1.0 sqm with suitable gauge of MS sheet, welding work, replacement of unserviceable door hinge, locking & arrange etc all as directed.

S&F aluminium lugs for the following sizes complete all as specified and directed :-

25 to 50 Sqmm

50 to 70 Sqmm

70 to 95 Sqmm

120 to 150 Sqmm

185 to 240 Sqmm

300 to 400 Sqmm

S&F in repair 15 mm dia Gun metal, globe or gate valves,with iron wheel head,screwed both ends for iron pipes and fixed.

S&F in repair bib cock 15 mm bore chromium plated cast copper alloy with screwed down, screwed for iron pipe or for brass ferrule and fixed.

Supplying & fixing in floors 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Supplying & fixing in floors 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Material and labour for glow sign boards for E/M installtions made up of retroreflective material (blue colour) fixed on stainless sheet of size 1.5 mtr x 1.0 x 3 mm including mounting arrangement with stainless steel pipe of 20 mm for board beadings and 40 mm size for vertical erection of length 2.5 mtrs including connected civil work like digging foundations, PCC etc required for vertical erection of sign board and writing the letters on sign board in white all as directed.

Material and labour for glow sign boards for E/M installtions made up of retroreflective material (blue colour) fixed on stainless sheet of size 0.4 mtr x 0.4 x 3 mm including mounting arrangement with stainless steel pipe of 20 mm for board beadings and 40 mm size for vertical erection of length 2 mtrs including connected civil work like digging foundations, PCC etc required for vertical erection of sign board and writing the letters on sign board in white all as directed.

M&L for Heat shrinkable PVC sleeve suitable for XLPE LT UG cable fo following sizes complete:-

Repair and prime servicing of diesel engine driven generating set 6 cylinder 160 KVA, BHP-195, RPM-1500 Make of Engine -: CUMMINS INDIA Ltd & Model - 6BTAA5.9GS ) installed at MH by carrying out the following jobs :-

Disconnecting the electrical connections and alternator from Engine, disconnect the inlet and exhaust manifold, turbocharger, exhaust pipes fuel connection, PT pump, water pump, air cleaners, hoses from the engine, dismantling the engine,drain out engine oil, striping out of engine assembly such as cylinder heads, tappet covers, piston assy, connecting rod, cam shafts, big end and small end bearing, injector assembly, oil pumps, crank shaft etc including all minor parts such as nut, bolts, ignition switch, control panel etc as directed at site and cleaning all parts by kerosene oil, segregating of serviceable and unserviceable parts. (a) Transportation of unserviceable body of engine such as Engine block, cylinder heads, water pump, oil pump, PT pump with injector from MH to workshop for repair. (b) Grinding work of crank shaft, block as per site requirement,boring, leth work, polishing & facing of cylinder heads, sleeves including minor repair to cylinder heads. (c) After repair, re-transportation to engine block, water pump, oil pump PT with injector assy and unserviceable spare parts from workshop to MH. (d) Re-assembling the Engine complete and connecting the alternator including proper alignment of generator with base frame complete. (e) Testing and commissioning of DG set after repair on full load up to the entire satisfaction of GE/ Engr-in-Charge.

Note: -(i) The major spare parts required for overhauling of engine shall be measured and paid for separately under relevant items of Sch 'A' as "Supply Only" item No. 2. (ii) Micro spare parts such as nuts, bolts, washers, banjo bolt, O rings copper washers etc required for proper functioning of DG set and not mentioned in Sch’A’ deemed to be included in the item rate. (iii) Make of all spare parts should be Cummins only or as per existing type & make

Supply only the following spare parts required for Diesel Engine of capacity 195 BHP, Model - 6BTAA5.9GS of Cummins make Engine

Gaskits complete set (Cat Part No. 3936563)

Piston assembly including piston pin (Cat Part No. 3907156)

Piston Ring set (Cat Part No. 3802040)

Valve set pairs (Cat Part No. 3935586)

Valve Seales (Cat Part No. 3935588)

Filter Kits complete -Set of three (Cat Part No. AX 1013815)

Main Bearing Std

CR (connecting rod) bearing std set

CR (connecting rod) bush set

Oil Pump (Cat Part No. 38753085)

Main Fan Belt (Cat Part No. KCL 3911560)

Main Seal

Timing Seal

Head Seal set

Piston bore sleeve

Exhaust bolt

Head bolt

Engine Oil 15W40

Coolant

Radiator water sensor

Oil safety sensor

Injector

Dismantling / taking down of radiator assambly complete from its mounting from engine and cleaning complete tube with suitable cleaning reagent to remove rust & scaling , plugging of any water leakage by brazing / welding / sealing work and re-installing in original position including replacement of all radiator hose pipe and seals complete with jupiter clamps for 160 KVA capacity of DG Sets complete all as specified and as directed. Make of Engine -: CUMMINS INDIA Ltd & Model - 6BTAA5.9GS

shyam construction

M/s DEVI DAYAL CONSTRUCTION CO