Interior Decoration, Renovation, Furnishing, Civil, Internal Electrification and other types works at any place of M.P.

Amount

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 Metres lead as directed by Engineer-in-Charge.

Dismantling tile/ Kota stone/ Marble / Granite work in floors/walls and roofs laid in cement mortar including stacking material within 50 Metres lead. For thickness of tiles 10 mm to 25 mm.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing periMetre channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the periMetre of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and periMetre channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of periMetre channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum board Fire resistant Glass Reinforced Gypsum (GRG) board conforming to IS: 2095- (Part 3) : 1996 (Board with BIS certification marks)

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diaMetre M-6 dash fasteners, 6 mm diaMetre fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI periMetre wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre& 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-incharge. With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6)

Providing and installation of acoustical wall panelling wood finish Slats made out of HDF board , Melamine / veneer laminated finish, perforated wooden grooved slats (2mm grooves @ 8mm centers) / (2mm Slats @16mm pitch) / (2mm grooves @ 32mm centers) / (2mm grooves @ 64mm centers), backlined with black acoustical fleece, tongue-groove edge for a seamless look, FR grade, of lineal dimension size 128mm x 2440mm x 16mm thick having density 1000Kg /m3, weight 12.8Kgs/m2 installed by using GI strut system. The GI strut system includes GI Cross channel having thickness 0.45mm, length 3600mm, knurled web 40mm, depth 10mm and equal flanges 15mm is fastened vertically/ horizontally at every 600mm centers. Aluminium core cross channel having thickness 0.5mm, length 2400mm, web 15mm and 27mm, depth 18mm and flanges of 7mm with suitable edge and centre brackets is then fixed perpendicular to the cross channel with the help of fasteners at every 400mm centers. Contractor to Provide expansion joints of 3mm at every 5mts bothways.

Providing and fixing stainless steel English (Capital) and Hindi letters instandard pattern bellow type made with 1.20 mm thick stainless steel (ASI Grade- 304 ) Depth of letter shall not be less than 30mm andrate includes welding/soldering of joints polishing,buffing and fixing on the wall, plateand beam surface at any height with necessary nut and bolts/fastener wherever is required complete as per direction of Engineer-in-Charge.

Providing and fixing of name plate for offices name of Stainless steel plate 304 grade of 1.50mm thick, including writing with computerized vinayle sheet letters of required size including fixing at required placed with studs, screws and rawl plugs etc. compete as per direction of Engineerin- Charge.

Providing and fixing Stainless steel plate 304 grade of 1.50mm thick, includingwriting with Embossing of letters of required size including fixing at required placed with studs, screws and rawl plugs etc. compete as per direction of Engineerin- Charge.

Finishing walls by any mechanical or manual means with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : 1Two or more coats applied on walls @ 1.25 ltr/10 sqm. Over and including one coat of Special primer applied @ 0.75 ltr / 10 sqm.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge. In cement mortar.

Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete to match existing surface i/c disposal of mulba/rubbish as directed by Engineer-in-charge. For door/ window/ clerestory window.

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50metres lead : With cement mortar 1:4 (1 cement : 4 sand).

4 mm thick alumminium composite pannel material consisting of 3 mm thick FR grade mineral core sandwiched between two alumminium sheets (each 0.5mm thick)

Providing and fixing aluminium magnesium alloy (FACADE) wall cladding system consisting of panels 200mm wide x 17mm deep x 0.5mm thick of maximum length of 6.0 mtr. coil coated on a continuous paint line double baked and roll formed from enamelled corrosion resistant GI pre-coated alloy for higher strength and roll forming characteristics, panel shall be clipped to baked enamel panel stringers of 34.5mm wide 48mm deep x 0.5mm thick GI alloy with cut-outs to hold the panel horizontally on the stringer in a module of 200mm centre to centre at a distance of maximum 1.20 mtr. The stringer shall be fixed to a suitable rigid structure. All panels shall be achromatised for maximum bond between metal and paint, enamelled twice under high temperature one side with full primer and the other side (inner side) with a primer coat on a continuous paint line, and fixed as per the direction of the Engineer-in-Charge.

Providing and fixing Aluminium Magnesium alloy Plain Panel Sun Louvres of approved colour consisting of panel 84 mm wide x 16mm deep x 0.6mm thick with round edges panel length upto 6 mtrs coil coated on a continuos paint line double baked and roll formed from enamelled corrosion Resistance Aluminium Alloy AA3005 (Al.Mg.) for higher strength and good Roll forming characteristics. Panel shall be clipped to baked enamelled Aluminium panel stringer of 33mm wide and 86mm deep x 0.95 mm thick in a standard length of 5mtrs made of double baked enamelled Aluminium Alloy AA5050 (Al.Mg.) black with cut-outs to hold the panel in a module of 86mm centre to centre at a distance of 1mtr. The carrier shall be fixed to a suitable structure by means of rigid fixing details. Paint Finish: Aluminium panels shall be chromatised for maximum bond between metal and paint, enamelled twice under high temperature one side with full primer and finish, the other side (inner side) with a primer coat and Skin Coat on a Continuos Paint Line.

Providing and fixing plywood 4 mm thick one side decorative veneer conforming to IS: 1328 (type-1) for plain lining / cladding with necessary screws, priming coat on unexposed surface with: Decorative veneer facings of approved manufacture.

Providing and fixing factory made UPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of UPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to UPVC profile), appropriate dimension of UPVC extruded glazing beads and UPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Mealamine polishing on door windows by preparing the surface applying putty base course. Prepare the surface smooth by sand papering and then applying mealamine polish with air compressor. Two or more coats on new works including a coat of wood filler.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand over the plastered wall surface to prepare the surface even and smooth i/c all cost of material, labour and scaffold etc in all position complete. Note : Putty shall be applied only on the internal walls, for application on the exterior walls prior permission of APD/Chief Engineer will be required.

Providing and laying vitrified floor tiles Multi/Double charged (Minimum top layer thickness 2.0mm) Neno Polished self design, in different size with water absorption less than 0.05% and conforming to IS:15622 of approved make in all colours& shades, quality/ premium quality in flooring laid on 12mm thick cement mortar 1:4(1cement :4sand) including grouting the joints with white cement and matching pigments etc. complete In light shade glossy/ rustic /stain finished Size 800X800mm thickness 11-12mm

Providing and laying vitrified floor tiles Multi/Double charged (Minimum top layer thickness 2.0mm) Neno Polished self design, in different size with water absorption less than 0.05% and conforming to IS:15622 of approved make in all colours& shades, 1st quality/ premium quality in skirting laid on 12mm thick cement mortar 1:4(1cement :4sand) including grouting the joints with white cement and matching pigments etc. complete In light shade glossy/ rustic /stain finished (b) Size 800X800mm thickness 11-12mm

Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required : White glazed fire clay kitchen sink of size 600x450x250mm.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40 mm dia

Providing and fixing 18mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish wherever required etc. complete at all levels. samples approved by Engineer-in-charge. Granite grey/pink/brown with various patterns

Providing and fixing 12mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25mm to 40mm thick. Fire retardant plywood conforming to IS: 5509.

Providing and Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive of approved quality. 1.0 mm thick.

Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6mm hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm centre to centre both ways (vertically and horizontally ) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or dash fastener shall be paid for separately). Kiln Head wood seasoned and chemically treated hard wood (Haldu, Kail, Bija wood.)

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutter. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing ISI marked stainless steel sliding door bolts with nuts and screws etc. complete : 250x16 mm

Providing and fixing ISI marked stainless steel tower bolt black finish, (Barrel type) with necessary screws etc. complete 200x10 mm

Providing and fixing ISI marked stainless steel handles with necessary screws etc. complete :125 mm

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing 12 mm thick toughened glass including all connectors and fixing accessories all complete for partitions, cubicals etc. As per direction of Engineer-in-Charge.

Extra for froasted glass (with eching film) in item No. 26

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-Charge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body /plate with double spring mechanism and door weight upto 125 kg., for doors, including cost of cutting floors , embedding in floors as required and making good the same matching to the existing floor finishing and coverplates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge : With brass cover plate - minimum 1.25 mm thickness.

Providing & fixing of imported 3D wall paper with high resolution including all fitting with wastage(Spin Décor / marshell / Green)

Roller Blinds MF- 201 Providing and fixing roller blinds Vista/Marvel make and shade with hanging and drawing system including all hardware and fixing complete.

Lock - Providing and fixing bright finished mortice latch and lock ISI marked with six lever and a pair of anodised(anodic coating not less than grade AC 10 as per IS:1868 aluminuium lever handles with necessary screws etc complete. Best make of approved quality.

Providing and fixing Satin stainless steel finish 400x16 mm sliding door bolts with nuts and screws etc. complete.

Providing and fixing Satin stainless steel finish 600 mm and 32mm dia Handle H Type with nuts and screws etc. complete.

Providing and fixing Dorma TS-68 door closure with standard arm EN2/3/4, necessary accessories and screws etc. complete.

Providing and Applying ultra tech texture paint required placed. compete as per direction of engineer-in-charge.

Providing And Placing of EXECUTIVE MAIN TABLE + SIDE TABLE WITH PEDESTAL : The Main Table should be of Size - 1800 x 900 x 750 with ERU With Pedestal of Size - 1200 x 500 x 750. The primary work surface should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Softclosing access flap with in-BACK UNITild power box are provided on work surface for wire management Secondary work surface ( ERU ) of size - 1200 x 600 x 750 should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Modesty Panel should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening Pedestals are provided with lock for security. Furniture Make- Haworth/ Herman Miller /Godrej/ Knoll (Greenguard/ BIFMA Certified Co.) Design as approved by Engineer-In-charge.

Providing And Placing of EXECUTIVE BACK UNIT : The back unit of Size - 1650 x 500 x 750 mm. Top panel should be made up of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Slide door unit should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves.. Shutters shall be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Shutters should have a soft closing & anti slam mechanism. Handles are provided for ease of opening.Storage is provided with lock for security.Furniture Make- Haworth/Herman Miller/Godrej/Knoll (Greenguard/BIFMA Certified Co.) Design as approved by Engineer-In-charge.

Providing And Placing of EXECUTIVE HIGH BACK CHAIR LEATHERITE. : The cushioned seat is to be made of injection molded plastic outer & inner. Plastic inner shall be upholstered with leatherette and moulded high resilience ( H R) Polyurethane foam of density 45+/-2kg/m compression. Seat Size should be 47.0 cm(W) x 48.0cm (D).The cushioned back is to be made of PU Foam with insitu molded MS E.R.WRound Tube of size 1.9+/-0.03cm x 0.16+/-0.0128cm. duely upholstered with leatherette. The High Back should be of size 47.7 cm(W) x 76.4 cm.(D). The armrest top should be moulded from polyurethane (PU) and mounted on to a drop lift adjusted type tubular armrest support made of 3.81+/-0.03cm x 0.2+/-0.01cm thk M.S E.R.W tube having chrome plated finish. The armrest height shall be adjustable up to 6.5+/0.5cm in 5 steps. Mechanism should be Active Bio - Synchro Mechanism. The adjustable tilting mechanism is to be designed with the following features:it should be 360D revolving type.Front pivot for tilt with feet resting on ground and continuous lumbar support ensuring morecomfort. Tilt Tension adjustment can be oprated in seating position. 5-position tilit limiter give option of variable tilt angle to the chair.Seat/back tilting ratio is of 1 : 2. The mechanism housing is to eb made of HPDC Aluminium black powder coated.. Seat adjustment is integrated in the seat through a sliding mechanism , Seat depth adjustment range is of 6.0+/- 0.5cm..Adjustable Back support back frame is to be connected Up/Dn mechanism housed in plastic T spine . It can be adjusted in the range of 7.42+/-0.5 cm for the comfortable back support to suit individual need. Pneumatic Ht adjustment has an adjustment stroke of 10.0+/-0.3 cm. The Pedestal ahall be of high pressure die cast polished Aluminium and fited with 5 nos. twin wheel castors. The pedestal is of 65.0 +/- 0.5cm pitch center dia (75.0+/-1.0cm with castors. The 5 bos. wheel castors shall be injestionmouldedin plastic having 6.0+0.1cm wheel diaMetre and assembled to pedestal. Furniture Make- Haworth/Herman Miller/Godrej/Knoll (Greenguard/BIFMA Level 2 Certified Product.) Design as approved by Engineer-In-charge.

Providing And Placing of Versa Neo VISITOR CHAIR FIXED : The chair should be of size 60.9 (W) x 64.3 (D) 99.5cm cushioned seat is to be made of injection molded plastic outer & inner. Plastic inner shall be upholstered with leatherette and moulded high resilience ( H R) Polyurethane foam of density 45+/-2kg/m compression. Seat Size should be 47.0 cm(W) x 48.0cm (D).The cushioned back is to be made of PU Foam with insitu molded MS E.R.WRound Tube of size 1.9+/-0.03cm x 0.16+/-0.0128cm. duely upholstered with leatherette. Mechanism - the tubular frame shall be cantilever type & made up of 02.54+/-0.03cm x 0.2+/-0.016cm thk S.S 202 tube. The back connect to frame through powder coated (DFT 40 -60 microns) high pressure die cast connector piece. Furniture Make- Haworth/Herman Miller/Godrej/Knoll (Greenguard GOLD/GRIHA/BIFMA Level 2 Certified) Design as approved by Engineer-In-charge.

Two seater Sofa - Providing and fixing in position fully upholstered sofa made with 18mm BWP ply and B grade teak wood frame. flat spring below foam at seat, stitching, slopes color, hemming with seat of 80mm thick softy foam and reckon filler, 100mm 40 density foam on back and arm with 40mm thick high density foam, seat and back covered with best quality markeen, and finished in fabric (of not less than Rs 1000 per mtr) of approved colour, texture and quality including teak wood molding / frame sofa to be made in the module of two seater with arms on both face, seat size 500x550mm over all depth 700mm. The cost is inclusive of all labour and material etc. complete in all respect as per drawing and direction given by Engineer in charge.

Table counter, 600 mm wide - Providing and fixing table of specified size to be made up of 18MM BWP ply as per drawing using approved make hardware, having a storage unit with one drawers as per given drawing. Provision has to be made for keyboard tray, CPU stand.All exterior surfaces to be finished in 1.0mm laminates / corian as required specified by Architect and inner surfaces finished in 1.0 mm laminate of approved shade with necessary hardware such as handles wire manager, telescopic drawer slides, etc as per design all exposed edges to be finished with first quality Teak Wood beading which is to be melamine polished / pu coating. The cost is inclusive of all materials and labouretc complete in all respect as per drawing and direction given by Engineer in charge.

Table 1800 x 750 x 750 - Providing and fixing table of specified size to be made up of 18MM BWP ply as per drawing using approved make hardware, having a storage unit with three drawers as per given drawing. Provision has to be made for keyboard tray, CPU stand. All exterior surfaces to be finished in 1.0mm laminates/ corian as required specified by Architect and inner surfaces finished in 1.0mm laminate of approved shade with necessary hardware such as handles wire manager, telescopic drawer slides, etc as per design all exposed edges to be finished with first quality Teak Wood beading which is to be melamine polished / pu coating. The cost is inclusive of all materials and labouretc complete in all respect as per drawing and direction given by Engineer in charge.

Side Table 1200 x 600 x 750 - Providing and fixing table of specified size to be made up of 18MM BWP ply as per drawing using approved make hardware. All exterior surfaces to be finished in 1.0mm laminates as required specified by Architect and inner surfaces finished in 1.0mm laminate of approved shade with necessary hardware such as handles,hingesetc as per design all exposed edges to be finished with first quality Teak Wood beading which is to be melamine polished / pu coating. The cost is inclusive of all materials and labouretc complete in all respect as per drawing and direction given by Engineer in charge.

Providing and fixing of storage units (laminate finish) (450 mm wide) - Providing and fixing at site file / storage cabinet made up of 18MM BWP ply with 1mm thick laminate as per drawing. All shelves and partitions to be made up of 18MM BWP ply and Pallah to be made up of 12mm. thick BWP ply fixed with hinges of approved make. All exposed edges to be finished with 1st quality teak wood beading to be melamine polished / PU coating and all inside surfaces to be finished with 1.00mm laminate. The cost is inclusive of all materials accessories, SS handles, lock, labour, etc. complete in all respect as per drawing and direction given by Engineer in charge.

The seat and back shall be made up of 1.2+/-0.1cm thick hot pressed plywood and Upholstered with fabric and moulded polyurethane foam all around. The moulded polyurethane foam shall be of density 55+/-5 kg/m ³, and hardness load 15-20 kgf as per IS:7888 for 25% compression. The dimensions of seat shall be- 49.0cm(W) x 44.0cm(D) and of back shall be 50 cm(W) x 47.0cm(H).The armrests should made of black integral skin polyurethane with 40-55 shore hardness and reinforced with M.S insert .The mechanism of the chair shall have following features : 360⁰ revolving type, Synchro single position mechanism, Tilt tension adjustment . The chair shall be provided with pneumatic height adjustmentwhich shall have stroke of 12 cm. The pedestial shall be injection moulded in black glass-filled Nylon. It shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65 +/- 1 cm pitch-centre-dia (70 +/- 1.0 cm with castors). The twin wheel castors shall be made black nylon. Overall dimensions of Chair shall be, Width of Chair - 70cm, Depth of Chair - 70 cm as measured from pedestal below. Height from ground - min 92.0 to max 104 cm. Seat height - min 45.0 to max 57.0cm. Dimensions tolerance / variations shall be within +/- 1 cm. Chair tested as per ANSI/BIFMA X7.1standards (HAWORTH/ HERMANMILLER/ GODREJ/ WIPRO/ FEATHERLITE/ HOF. MAKE )

The cushioned seat assembly shall consists of moulded polyurethane foam upholstered with fabric. The foam is assembled over a 12mm thick hot pressed plywood . The back shall made up of two piece injection moulded frame. The inner frame shall be upholstered with mesh fabric and mounted on the main assembly. Size of back shall be (W)-46 cm, (H)-55 cm & size of seat shall be (W)-48 cm x (D)-44.0cm. Armrest is fixed . The arm top is made of soft moulded PU .The mechanism of chair shall have following features:360 degree revolving type, Synchro mechanism, Tilt tension adjustment, multi position tilt limiter with Back-safety return feature. The chair shall be provided with pneumatic height adjustment which shall have stroke of 95 +/- 5 mm. The pedestal shall be made of nylon. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 1 cm pitch-centre-dia (70.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in PP . Overall dimensions of Chair shall be, Width of Chair - 70.0cm, Depth of Chair - 70.0 cm as measured from pedestal below. Height from ground - min 95 to max 104 cm. Seat height - min 45.0cm to max 54.0cm. Dimensions tolerance / variations shall be within +/- 1 cm. Chair tested as per ANSI/BIFMA x5.1 standards (HAWORTH/ HERMANMILLER/ GODREJ/WIPRO/ FEATHERLITE/ HOF. MAKE )

Three seater Sofa - Providing and fixing in position fully upholstered sofa made with 18mm BWP ply and B grade teak wood frame. flat spring below foam at seat, stitching, slopes color, hemming with seat of 80mm thick softy foam and reckon filler, 100mm 40 density foam on back and arm with 40mm thick high density foam, seat and back covered with best quality markeen, and finished in fabric (of not less than Rs 1000 per mtr) of approved colour, texture and quality including teak wood molding / frame sofa to be made in the module of three seater with arms on both face, seat size 500x550mm over all depth 700mm. The cost is inclusive of all labour and material etc. complete in all respect as per drawing and direction given by Engineer in charge.

Centre Table 900x600x400 - Providing and placing center table as per drawing made of 18MM BWP ply finished with 1.0mm laminate of approved shade. The top covered with 12mm. thick toughened glass with polished and beveled edges fitted with 3" stainless steel studs. The cost is inclusive of all labour and material etc. complete in all respect as per drawing and direction given by Engineer in charge.

Corner Table480x485x400 - Providing and placing corner table as per drawing made of 18MM BWP ply finished with 1.0mm laminate of approved shade. The top covered with 12mm. thick toughened glass with polished and beveled edges fitted with 3" stainless steel studs. The cost is inclusive of all labour and material etc. complete in all respect as per drawing and direction given by Engineer in charge.

Providing and fixing of Conference Hall /Marketing room Table 600mm. wide made of 18MM BWP ply finished with 1 mm thick laminate inner and outer side. The table top front will be 24mm. thick with teak wood beading. Provision for foot rest, wire manager shall be made. all exposed edges to be finished with first quality Teak wood beading which is to be melamine polished/ pu coating. The cost is inclusive of all materials and labouretc complete in all respect as per drawing and direction given by Engineer in charge.

Providing and fixing 10mm thick acid and/ or alkali resistant tiles of approved make and colour using acid and/ or alkali resisting mortar bedding and joints filled with acid and/ or alkali resisting cement as per IS : 4457 complete as per the direction of Engineer-in- Charge. In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement: 4 sand)Acid and alkali resistant tile.

Fixing glazed/ Ceramic/Rectified/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness.

Providing and laying rectified Glazed Ceramic wall tiles 300x450 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in all colours white, ivory, grey, fume red brown laid on 12 mm thick cement mortar 1:3 (1 Cement : 3 sand) including grouting the joints with white cement and matching pigments etc., complete.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work.

Providing and fixing soil, waste and vent pipes : Spun cast iron socket and spigot (S&S) pipe as per IS: 3989 100 mm dia with wall thickness of 4 mm

Providing and fixing soil, waste and vent pipes : Spun cast iron socket and spigot (S&S) pipe as per IS: 3989 75 mm dia with wall thickness of 3.5 mm

17.34 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of Cement Concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. : For 100 mm dia. Pipe

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of Cement Concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. : For 75 mm dia. Pipe

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 110 mm dia Spun cast iron as per IS – 3989 minimum wall thickness 4 mm

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 75 mm dia Spun cast iron as per IS – 3989 minimum wall thickness 3.5 mm

Providing and fixing collar: 100 mm Sand cast iron SandS as per IS - 1729

Providing and fixing collar: 100 mm Sand cast iron SandS as per IS - 3989

Providing lead caulked joints to sand cast iron/ centrifugally cast (spun) iron pipes and fittings of diaMetre: 100 mm

Providing lead caulked joints to sand cast iron/ centrifugally cast (spun) iron pipes and fittings of diaMetre: 75 mm

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet Sand cast iron SandS as per IS: 3989.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 75 mm outlet Sand Cast iron SandS as per IS- 1729.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shape with 6 mm thick hard board backing : Rectangular shape 1500x450 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work including cutting chases and making good the walls etc. 20 mm nominal outer dia. Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass hreaded fittings. This included jointing of pipes and fittings with one step CPVC solvent cement, trenching, refilling and testing of joints complete as per direction of Engineer-in-Charge. 20 mm nominal outer dia .Pipes.

Providing and fixing CPVC gate valve with knob of approved quality. 25 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 30 cm length 20 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and laying below ground unplasticised PVC pipe to with stand working pressure of 4 kg/cm2 soild waste pipes confirming to IS:13592 and IS:4985 including jointing with seal ring confirming to IS :5282 leaving 10mm gap for thermal expansion all necessary fittings etc. complete. Excavation to be paid seperataly. 110 mm diaMetre OD (min. wall thickness 3.2mm)

Providing and laying cement concrete 1:3:6 (1 cement : 3 sand : 6 graded stone aggregate 20 mm nominal size) all-round PVC. pipes including bed concrete as per standard design: 110 mm diaMetre PVC. Pipe

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and fixing white vitreous china pedestal type Anti germ Fluoro-Polymer Coated Water Closet (European type W. C. pansize 390 X 365 X 540 MM) with soft closing seat cover, and 7.2 litre Low level slim dual flushing, PP (Poly Propeline) made 80 mm thick consealed flushing cistern, flushing capcity 3 litre/6 litre, with all fittings and fixures complete including cutting and making good the wall and floors wherever required : Anti germ Fluoro-Polymer Coated (neno coating) European W. C. Size 390 X 365 X 540mm with solid poly propelyne made soft closing seat cover.

Providing and fixing white vitreous china type Anti germ Fluoro-Polymer Coated Wash Basin size 190x600x435mm with C.I. Brakets, 15 mm C. P. wall mounted pressmatic pillar cock auto closing system (decol technology), 32 mm C.P. brass made waste coupling length 130mm and 32 mm C.P. Brass Made Bottle Trap size 200x300mm fittings and fixures complete including Painting of fittings and cutting and making good the wall and floors wherever required : White Vetrious China Anti germ Fluoro-Polymer Coated Wash Basin Size 190x600x435mm with wall mounted pressmatic pillar cock auto closing system (decol technology).

Providing and fixing white vitreous china Flat Back Anti germ Fluoro-Polymer Coated urinal (Inbuilt spreaders, Inbuilt Bottle trape and inbuilt ceramic Waste coupling) Size 670 X 330 X325 mm with 15mm Brass made presmatic auto closing consealed urinal flush valve with wall flange (Decol technology, 400000 operation warranted) complete including painting of fittings and brakets, cutting and making good the wall and floors wherever required : White Vetrious China Anti germ Fluoro-Polymer Coated Urinal Size 670 X 330 X325 mm with 15mm Brass made presmatic auto closing consealed urinal flush valve with wall flange (Decol technology, 400000 operation warranted)

Providing and fixing in position best indian ( bonut size 24mm, ceramic disc size 19mm and min. body thickness 2mm, nickel plating 0.10 micron and chrome plating 0.3 micron, quarter turn) Pillar cock.

Providing and fixing in position best indian ( bonut size 24mm, ceramic disc size 19mm and min. body thickness 2mm, nickel plating 0.10 micron and chrome plating 0.3 micron, quarter turn)Bib cock.

Providing and fixing in position best indian ( bonut size 24mm, ceramic disc size 19mm and min. body thickness 2mm, nickel plating.10 micron and chrome plating 0.3 micron, quarter turn)Angular stop cock.

Providing and fixing in position best indian ( bonut size 24mm, ceramic disc size 19mm and min. body thickness 2mm, nickel plating 0.10 micron and chrome plating 0.3 micron, quarter turn)Consealed stop cock.

Providing and fixing in position best indian C. P. Brass made (0.3 micron Chrom and 10 micron Nickel plated) Soap Dish Holder .

Providing and fixing in position best indian C. P. Brass made (0.3 micron Chrom and 10 micron Nickel plated) Soap Dispenser with Metallic Bottle .

Providing and fixing in position best indian C. P. Brass made (0.3 micron Chrom and 10 micron Nickel plated) Toilet paper holder with Flap .

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints etc. as required as per specification for :- Light Point/Fan Points. Primary short point

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints etc. as required as per specification for :- Light Point/Fan Points. Primary Medium point

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints etc. as required as per specification for :- Light Point/Fan Points. Primary Long point

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints etc. as required as per specification for :- (Light point/fan points) looping point Secondary short point

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints etc. as required as per specification for :- (Light point/fan points) looping point Secondary Medium point

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints etc. as required as per specification for :- (Light point/fan points) looping point Secondary Long point

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints etc. as required as per specification for :- 3 Pin 6 Amp socket outlet on Separate Board- Short point

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints etc. as required as per specification for :- 3 Pin 6 Amp socket outlet on Separate BoardMedium point

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints etc. as required as per specification for :- 3 Pin 6 Amp socket outlet on Separate BoardLong point

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints etc. as required as per specification for :- Call Bell / Buzzer Points Short point

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints etc. as required as per specification for :- Call Bell / Buzzer Points Medium point

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints etc. as required as per specification for :- Call Bell / Buzzer Points Long point

Point wiring (excluding metallic switch box & sheet but including switches, sockets) for 3 pin 6 Amp. Socket outlet point with 1.5 Sq. mm. PVC insulated cable FR with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5 Sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit with required materials as per specification on same board .

Wiring for circuit wiring with PVC insulated cable FR with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) of ISI marked suitable size etc. as required as per specification. a) 2x2.5 Sq.mm.

Wiring for circuit wiring with PVC insulated cable FR with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) of ISI marked suitable size etc. as required as per specification. b) 4x2.5 Sq.mm.

Wiring for circuit wiring with PVC insulated cable FR with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) of ISI marked suitable size etc. as required as per specification. c) 6x2.5 Sq.mm.

Point wiring (excluding metallic switch box & sheet ) for 3 Pin 16 Amp. Socket Outlet Point With 4 Sq. mm. PVC insulated cable FR with copper multi strand conductor ISI marked in Concealed rigid P.V.C.Conduit (HMS) ISI Marked of suitable size etc. with 16 Amp. F.T. Switch & Socket / S.S.Combined 6/16 Amp. of ISI Marked and 4 Sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit as per specification for :- On Separate Board C. Long Point

Point wiring (excluding metallic switch box & sheet ) for 3 Pin 16 Amp. Socket Outlet Point With 4 Sq. mm. PVC insulated cable FR with copper multi strand conductor ISI marked in Concealed rigid P.V.C.Conduit (HMS) ISI Marked of suitable size etc. with 16 Amp. F.T. Switch & Socket / S.S.Combined 6/16 Amp. of ISI Marked and 4 Sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit as per specification for :- On Separate Board D. Extra Long -I

Point wiring (excluding metallic switch box & sheet ) for 3 Pin 16 Amp. Socket Outlet Point With 4 Sq. mm. PVC insulated cable FR with copper multi strand conductor ISI marked in Concealed rigid P.V.C.Conduit (HMS) ISI Marked of suitable size etc. with 16 Amp. F.T. Switch & Socket / S.S.Combined 6/16 Amp. of ISI Marked and 4 Sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit as per specification for :- On Separate Board E. Extra Long -II

Point wiring (excluding metallic switch box & sheet ) for 3 Pin 16 Amp. Socket Outlet Point With 4 Sq. mm. PVC insulated cable FR with copper multi strand conductor ISI marked in Concealed rigid P.V.C.Conduit (HMS) ISI Marked of suitable size etc. with 16 Amp. F.T. Switch & Socket / S.S.Combined 6/16 Amp. of ISI Marked and 4 Sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit as per specification for :- On Separate Board F. Extra Long -III

Point wiring (excluding metallic switch box & sheet ) for 3 Pin 16 Amp. Socket Outlet Point With 4 Sq. mm. PVC insulated cable FR with copper multi strand conductor ISI marked in Concealed rigid P.V.C.Conduit (HMS) ISI Marked of suitable size etc. with 16 Amp. F.T. Switch & Socket / S.S.Combined 6/16 Amp. of ISI Marked and 4 Sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit as per specification for :- Same board switch socket 6/16 Amp

Supplying and fixing of approved make modular type metal box with modular frame/ base plate and cover plate including fixing in concealed / surface excluding switch,socket etc. as required for:- 3 Module

Supplying and fixing of approved make modular type metal box with modular frame/ base plate and cover plate including fixing in concealed / surface excluding switch,socket etc. as required for:- 4 Module

Supplying and fixing of approved make modular type metal box with modular frame/ base plate and cover plate including fixing in concealed / surface excluding switch,socket etc. as required for:- 6 Module

Supplying and fixing of approved make modular type metal box with modular frame/ base plate and cover plate including fixing in concealed / surface excluding switch,socket etc. as required for:- 8/9 Module

Supplying and fixing of approved make modular type P.V.C. box with modular base and cover plate including fixing on surface excluding switch,socket etc. as required for:- 1/2 Module

Supplying and fixing of approved make modular type P.V.C. box with modular base and cover plate including fixing on surface excluding switch,socket etc. as required for:- 3 Module

Supplying and fixing of approved make modular type P.V.C. box with modular base and cover plate including fixing on surface excluding switch,socket etc. as required for:- 4 Module

Supplying and fixing of approved make modular type P.V.C. box with modular base and cover plate including fixing on surface excluding switch,socket etc. as required for:- 6 Module

Supplying and fixing of approved make modular type P.V.C. box with modular base and cover plate including fixing on surface excluding switch,socket etc. as required for:- 8 / 9 Module

Supplying and drawing single core PVC insulated cable FR with copper multi strand conductor ISI marked in existing rigid PVC Casing-N-Capping / conduit in surface or concealed as per specification. 1 X 1.5 sq mm (c) 3 X 1.5 sq mm

Supplying and drawing single core PVC insulated cable FR with copper multi strand conductor ISI marked in existing rigid PVC Casing-N-Capping / conduit in surface or concealed as per specification. 1 X 2.5 sq mm (a) 1 X 2.5 sq mm

Wiring for sub-mains with PVC insulated cable FR with copper multi strand conductor ISI marked in recessed / concealed rigid PVC conduit (HMS) ISI marked of suitable size(Conduit included) including 2mm thick accessories, connection etc ,as required as per specification 2 WIRE SUB-MAIN 4.0 sq mm cable in 25 mm conduit

Wiring for sub-mains with PVC insulated cable FR with copper multi strand conductor ISI marked in recessed / concealed rigid PVC conduit (HMS) ISI marked of suitable size(Conduit included) including 2mm thick accessories, connection etc ,as required as per specification 2 WIRE SUB-MAIN6.0 sq mm cable in 25 mm conduit

Wiring for sub-mains with PVC insulated cable FR with copper multi strand conductor ISI marked in recessed / concealed rigid PVC conduit (HMS) ISI marked of suitable size(Conduit included) including 2mm thick accessories, connection etc ,as required as per specification 4 WIRE SUB-MAIN 10.0 sq mm cable in 32 mm conduit

Supply and drawing PVC insulated copper cable (earth continuity conductor) of green colour FRLS with copper multi strand conductor ISI mark in existing conduit along with other wires as required as per specification : 4 Sq mm

Supply and drawing PVC insulated copper cable (earth continuity conductor) of green colour FRLS with copper multi strand conductor ISI mark in existing conduit along with other wires as required as per specification : 6 Sq mm.

Supplying of ISI Marked and approved make of Moulded Case Circuit Breaker (MCCB) suitable for 3 phase,3 pole, 50 Hz, 415 Volts, AC supply with respective interrupting capacity (KA) at 415 Volts cited against their range standard conforming to IS – 8828-MCCB with Breaking Capacity 35 KA at 415 V Current Rating -160 Amps & Adjustable: 80% -100% thermal

Supply of ISI marked and accepted standard of miniature circuit breaker (MCB) of 'C' series with short circuit indication, suitable for 240/415 Volts,50 Cycle, 10 kA/15 kA Value AC supply conforming to IS : 8828 : 1996, IEC : 60898 :2002 & 60947-2 but without enclosures :- Single pole- MCB SP 6Amp to 32Amp 10kA rating

Supply of ISI marked and accepted standard of miniature circuit breaker (MCB) of 'C' series with short circuit indication, suitable for 240/415 Volts,50 Cycle, 10 kA/15 kA Value AC supply conforming to IS : 8828 : 1996, IEC : 60898 :2002 & 60947-2 but without enclosures :- Single pole- MCB SP For 40Amp 10kA rating

Supply of ISI marked and accepted standard of miniature circuit breaker (MCB) of 'C' series with short circuit indication, suitable for 240/415 Volts,50 Cycle, 10 kA/15 kA Value AC supply conforming to IS : 8828 : 1996, IEC : 60898 :2002 & 60947-2 but without enclosures :- Double pole- MCB DP 6Amp to 32Amp 10kA rating

Supply of ISI marked and accepted standard of miniature circuit breaker (MCB) of 'C' series with short circuit indication, suitable for 240/415 Volts,50 Cycle, 10 kA/15 kA Value AC supply conforming to IS : 8828 : 1996, IEC : 60898 :2002 & 60947-2 but without enclosures :- For Triple pole MCB TP For 40Amp 10kA rating

Supply of ISI marked and accepted standard of miniature circuit breaker (MCB) of 'C' series with short circuit indication, suitable for 240/415 Volts,50 Cycle, 10 kA/15 kA Value AC supply conforming to IS : 8828 : 1996, IEC : 60898 :2002 & 60947-2 but without enclosures :- For Triple pole -MCB TP 50Amp to 63Amp 10kA rating

Supply of approved make powder coated sheet steel encloser SPN MCB DB inclusive of Busbar, Neutral bar, Earth bar & two earth terminals etc. complete as per IS:13032( exclusive of MCB & isolator )-- 2 way single door

Supply of approved make powder coated sheet steel encloser SPN MCB DB inclusive of Busbar, Neutral bar, Earth bar & two earth terminals etc. complete as per IS:13032( exclusive of MCB & isolator )-- 6 way Double Door IP 43 protection

Supplying of approved make TPN MCB DB Metal Double Door IP 43 protection with provision for FP MCB/Isolator/RCCB/RCBO as incomer and SP MCBs as outgoing inclusive of Busbar, Neutral bar, Earth bar & two earth terminals etc. complete as per IS:13032( exclusive of MCB & isolator ): -6 way (8+18)

Supplying of approved make, powder coated metal double door vertical TPN MCB DB IP 43 protection with provision for MCCB upto160A TP/FP 36kA as incomer and space for SP/TP MCBs as outgoing (without MCCB/MCBs) inclusive of busbar& connections etc -4 way without MCCB

Fixing of MCB/MCCB/Isolator in sheet steel enclosure as required as per accepted practice, including mounting on busbar and cable connection etc. complete (labour only) MCB / Isolator SP/DP

Fixing of MCB/MCCB/Isolator in sheet steel enclosure as required as per accepted practice, including mounting on busbar and cable connection etc. complete (labour only) MCB /MCCB Isolator TP /TPN/FP

Labour charges for fixing sheet steel enclosures, MCB DB flush mounting type, as per accepted practice, duly embedded and end plate completely flushed in wall, cable connection etc.complete.

Labour charges for fixing sheet steel enclosures, MCB DB flush mounting type, as per accepted practice, duly embedded and end plate completely flushed in wall, cable connection etc.complete.

Supplying and fixing as per specification Call bell / buzzer of approved make with necessary materials complete.- Multi sound bell

Supplying, erection and testing of approved make Wall Mounting fan complete with Wall Bracket ,canopy, blades, speed Regulator etc .A.C 230-250 volts with connections and including raw bolt/Anchor hole fastener etc. complete finished of approved as required.- 300 sweep

Supplying, erection and testing of approved make 'Fresh Air Fan' AC 230-250 volts with connection and including frame bolt/Anchor hole fasteners etc. complete finished of approved as required.- 300mm sweep

Supply and fixing of recessed mounting type Led light fixture, LED of 1 to 3 Watt each assembled on single MCPCB, having color temp upto 6500K & having 50000 burning hrs life with minimum @ L 70, system lumen output should be minimum with efficacy>100 lm/Watt. LED driver PF> 0.95, THD < 20% & surge protection 4KV. The colour rendering index of LED light should be more than 70. Housing made of CRCA powder coated frame with glare free diffused polycarbonate cover. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job.- LED luminiare 2' X 2', 36Watt, color temp 3000- 6500k as required.

Supply and fixing recessed mounting LED down lighter, LED of 1 to 3 Watt each assembled on single MCPCB, having color temp upto 6500K & having 50000 burning hrs. life with minimum @ L 70, system lumen output should be minimum with efficacy>100 lm/Watt. LED driver PF > 0.95, THD < 20% & surge protection 4KV. The colour rendering index of LED light should be more than 70. Housing made of pressure die cast aluminium/CRCA powder coated frame with glare free diffused polycarbonate cover. Submission LM 79- 08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job.- 3 Watt, color temp 3000-6500k as required.

Supply and fixing recessed mounting LED down lighter, LED of 1 to 3 Watt each assembled on single MCPCB, having color temp upto 6500K & having 50000 burning hrs. life with minimum @ L 70, system lumen output should be minimum with efficacy>100 lm/Watt. LED driver PF > 0.95, THD < 20% & surge protection 4KV. The colour rendering index of LED light should be more than 70. Housing made of pressure die cast aluminium/CRCA powder coated frame with glare free diffused polycarbonate cover. Submission LM 79- 08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job. 5/6 Watt, color temp 3000-6500k as required.

Supply and fixing recessed mounting LED down lighter, LED of 1 to 3 Watt each assembled on single MCPCB, having color temp upto 6500K & having 50000 burning hrs. life with minimum @ L 70, system lumen output should be minimum with efficacy>100 lm/Watt. LED driver PF > 0.95, THD < 20% & surge protection 4KV. The colour rendering index of LED light should be more than 70. Housing made of pressure die cast aluminium/CRCA powder coated frame with glare free diffused polycarbonate cover. Submission LM 79- 08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job. 7/8 Watt, color temp 3000-6500k as required.

Supply and fixing recessed mounting LED down lighter, LED of 1 to 3 Watt each assembled on single MCPCB, having color temp upto 6500K & having 50000 burning hrs. life with minimum @ L 70, system lumen output should be minimum with efficacy>100 lm/Watt. LED driver PF > 0.95, THD < 20% & surge protection 4KV. The colour rendering index of LED light should be more than 70. Housing made of pressure die cast aluminium/CRCA powder coated frame with glare free diffused polycarbonate cover. Submission LM 79- 08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job. 12 Watt, color temp 3000-6500k as required.

Supply and fixing recessed mounting LED down lighter, LED of 1 to 3 Watt each assembled on single MCPCB, having color temp upto 6500K & having 50000 burning hrs. life with minimum @ L 70, system lumen output should be minimum with efficacy>100 lm/Watt. LED driver PF > 0.95, THD < 20% & surge protection 4KV. The colour rendering index of LED light should be more than 70. Housing made of pressure die cast aluminium/CRCA powder coated frame with glare free diffused polycarbonate cover. Submission LM 79- 08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job. 14/15 Watt, color temp 3000-6500k as required.

Supply of XLPE Insulated power cable (confirming IS-7098 Part-I ) 1100 Volt grade, 1 core /2 core /3½ core/4 core ISI MARKED with Alu. Stranded /solid conductor :- 3½ CORE ARMOURED 25 Sq. mm

Supply of XLPE Insulated power cable (confirming IS-7098 Part-I ) 1100 Volt grade, 1 core /2 core /3½ core/4 core ISI MARKED with Alu. Stranded /solid conductor :- 3½ CORE ARMOURED -35 Sq. mm

Supplying and fixing heavy duty cable gland for P.V.C. insulated armoured cable with brass washer, Rubber ring complete erected with cable and lead connection etc. as per specification complete.:- Gland size 38mm 3½ x 70 Sq.mm, 3x95 Sq.mm

Supplying and fixing cramping type Alum. lugs as per I.S.S. Specification suitable for following size of cable with Alu. /Copper solid/stranded conductor evently cramped with high/pressure tool and connected to switch gear/Bus/M.C.C.B./ M.C.B. etc. as required complete. For Conductor Size- 70 Sq.mm

Supplying, fixing & testing of approved make flexible LED strip comprising of 60 LED per Metre W/O driver for direct mounting complete with all accessories including connection lead, fixing, connection as required. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job.-Flexible LED strip 24Watt/25Watt - 5 M indoor cove light W/O Driver IP 20 -33

Supplying, fixing & testing of approved make Power supply for LED strip ;- Power supply 25Watt/30Watt for LED strip IP25/IP33

Supply, installation, testing and commissioning of UPS with isolation transformer & battery for backup, having three phase input with ground (R-Y-B-N-G), Voltage range 190v AC-478v AC (based on load %), line low transformer (0-50% :190v/51-100% : 305v ± 3% VAC), line low comeback +25 - 35 VAC ( ± 3%), line high transfer 478 VAC (± 3%), line high comeback 461 VAC (± 3%), frequency range 46 - 54 Hz, power factor 0.99, Total harmonic distortion (current)-THDi (<5% with full load, having output voltage 220 VAC/230 VAC/240 VAC, voltage regulation ± 1%, frequency 50 Hz ± 0.1 Hz, Synchronization range 46 -54 Hz, voltage distortion ≤ 2 % (linear load) & ≤ 5 % (nonlinear load), having pure sine wave output waveform, crest factor 3 : 1, efficiency (AC - AC) 94%, power factor 0.9, having inbuilt isolation transformer, over load 101 - 109% : 5 Min, 110 - 129% : 1 Min, 130 - 150% : 10 sec, having SMF/VRLA battery type, transfer time line mode to battery mode 0 ms, inverter to bypass, ECO mode 0 ms, bypass to inverter 0 ms, ECO to inverter mode < 10 ms, when bypass voltage of frequency is out of range, having features Eco mode, Fan speed control, EPO function, frequency converter mode & parallel function (optional) up to 4 units. Operating temperature 0 - 45°C, noise level < 55 db @ 1 Metre having display & indication features i.e. user friendly dot matrix LCD display, input : voltage & frequency, battery : voltage & level in %, internal DC bus voltage z frequency, current, power& load level in %), UPS status (operating mode/warning/fault/codes (fault & warnings), UPS settings (output voltage/ frequency/ bypass enable/disable/special function., UPS/CVCF/ECO. LED status (normal mode/load on battery/load on bypass/system fault), Audible alarm (main failure alarm, low battery alarm, UPS warning, overload, fault & bypass mode etc.), protections (advance electronic protection for device, safety backed with MCBs, fast acting fuses, high speed pulse blanking, electronic overvoltage/under voltage), connections (terminal block for input/bypass/battery & output), static bypass, communication interface RS 232/USB port for software interface, intelligent slot for SNMP (optional). UPS installation with all required material arrangements as required as per IS specification. 10 KVA (3 phase input & 1 phase output) For 30 minute backup, min. 8000 VAH

Supply and fixing OF Deep recessed mounting LED down lighter, having color temp upto 6500K & having 50000 burning hrs. i/c connection wire, testing etc. to complete the job.- 12 Watt, color temp 3000-6500k as required.

Supply and fixing OF Deep recessed mounting LED down lighter, having color temp upto 6500K & having 50000 burning hrs. i/c connection wire, testing etc. to complete the job.- 14/15 Watt, color temp 3000-6500k as required.

Supplying installation and testing 9 - 18 watt Decorative Hanging Light, Approved by Consultant or Engineer in charge. Make: Jaquar/Tisva

Supplying installation and testing 9 - 18 watt Decorative Washer Light, Approved by Consultant or Engineer in charge.

SPLIT AC (inverter model) :- Supply, installation, testing and commissioning of Split type wall mounted air conditioning unit of following capacity including indoor, outdoor unit fitted with inverter based rotary compressor, copper condenser and first charge refrigerant R410A. The condensing unit working range should be capable for providing cooling between +/-5 deg. C to 50 deg. C & heating within 0 deg. C to 15 deg. C including connection of copper pipe of required size upto 3 mtr., insulation, cordless remote control, auto air swing louvers, wall stand for outdoor unit, connection copper lead wire, condensed water outlet pipe 2 mtr. completeetc as required. Outdoor/indoor units should be of same make (brand). SPLIT AC (inverter model, Cooling only)- 1.8/2 TR star rating 3 star

Supply, installation, testing & commissioning of suction/discharge copper pipe line in split air conditioning unit 1.0/1.5 TR/2 TR/3 TR capacity including brazing, nitrile rubber insulation 6/9mm thick class 'O', etc complete as required.-Copper tube 1/4"

Supply, installation, testing & commissioning of suction/discharge copper pipe line in split air conditioning unit 1.0/1.5 TR/2 TR/3 TR capacity including brazing, nitrile rubber insulation 6/9mm thick class 'O', etc complete as required-Copper tube 3/8"

Supply, installation, testing & commissioning of suction/discharge copper pipe line in split air conditioning unit 1.0/1.5 TR/2 TR/3 TR capacity including brazing, nitrile rubber insulation 6/9mm thick class 'O', etc complete as required- Copper tube 1/2"

Supply, installation, testing & commissioning of suction/discharge copper pipe line in split air conditioning unit 1.0/1.5 TR/2 TR/3 TR capacity including brazing, nitrile rubber insulation 6/9mm thick class 'O', etc complete as required- Copper tube 5/8"

Drain Piping :- Providing and fixing of CPVC, 6Kg/cm2 drain water piping with fittings, support and insulated with 6 mm thick closed cell elastomeric nitile rubber insulation complete as per specification. 25 mm dia ID

CONTROL CABLE :- Supply and laying ,testing & commissioning of following sizes of Copper conductor control cables on existing tray, including fixing clamps & proper connections to equipment etc.complete as required. 4C x 1.5 Sq. mm

OUTDOOR STAND FABRICATION :- Supply, fabrication and erection of Angle/Chanel/Flat iron stand, hanging arrangement for air conditioning machines & ducts etc, Back /Support clamps or other similar work etc. including nut bolts of required size, making holes, fabrication, welding, cutting, etc. and painting with one coat of red oxide paint & two coat of 'enamel paint as required as per specification

Supplying and drawing following pair, 0.5 mm PVC insulated copper conductor unarmoured telephone cable in existing surface/concealed, steel/PVC conduit as required.- Telephone wire 0.5 mm, 2 Pair

Supplying and drawing following pair, 0.5 mm PVC insulated copper conductor unarmoured telephone cable in existing surface/concealed, steel/PVC conduit as required.- Telephone wire 0.5 mm, 4 Pair

Supply installation, testing and commissioning of 0.5 mm size solid annealed copper, jelly filled telephone cables, polythene insulated, petroleum jelly filled with poly-al laminate moisture barrier, polythene sheathed, unarmoured polythene jacketed telephone cables as per DOT specifications of following sizes 10 Pair

Supply, Installation testing and commissioning of telephone Tag block Krone connector with enclosure and lock complete as mentioned below :- 50 Pair

Supply, fixing and testing of RJ 11 telephone jack modular (1 Module)

Supply, installation testing and commissioning RJ - 45 computer jack cat 6 with shutter modular (1Module)- RJ - 45 computer socket cat 6 tool less connection (1Module)

Supplying and drawing 4 pair un-shielded twisted pair (UTP), 0.5 mm PVC insulated copper conductor un-armoured Cat-6 computer cable FRLS in existing surface/concealed, steel/PVC. conduit/ casing-n-capping as required.

Supply, installation testing and commissioning of 19" modular patch - 1 U patch panel 24, RJ 45 cat-6 connector

Supply, Installation testing and commissioning of wall mounting rack, for computer switches complete as mentioned below :- 12U cabinet 600X600X500, wall mounting with 6 point 5 Amp. socket power supply strip and fan, tray.

Supply, installation, testing and commissioning of EPABX system consist, no. of extension, no of junction, no. of expandable eport, operating console, current on max. load with ISDN compatible of approved make and labor as required as per specifications.-EPABX system consists of 16 nos. extensions, 8 nos of junction &upto 64 nos. of expandable eport, with one operating console, 1.35 Amp max. current

Supplying, fixing essential additional accessories to EPABX system of approved make with all necessary material as required as per specifications.- EPABX system line card to extend the number of line by 8

Supplying, fixing essential additional accessories to EPABX system of approved make with all necessary material as required as per specifications.- 4 push button CLI phone.

Providing & Fixing of 24-Port Data Switch of [Managed Layer-2 with 2-Giga Ports (10/100/1000) ] Make: D-link/Cisco

Fire panel : Providing, fixing, testing & commissioning microprocessor based main fire alarm panel and indicating panel solid state modular card type pulsar, timer for dual stage alarm facility with indicators, standby battery ,complies to IS 2189:1999.2 x 16 character backlit LCD display lamp test features. Complete with integral power supply and battery charger for SMF battery. NO/NC contacts for both fire and fault. Switches to enable on board operation. LCD and LED Indication for open, short circuit, Isolate, fire in each zone. reset, lamp test, silence, isolate, short, open, fire continuous buzzer for fault and intermittent buzzer for fire battery charger box, operating voltage 220 Volt mains A.C. input/24V D.C. output etc. complete in all respect. 2 zone fire panel

Smoke detector (ionization type) : Providing &fixing of ionization type smoke detectors as per IS: 11360-1985 of dual chamber, 12/24 volt DC, ionization source-less than one micro curie maximum Americium 241, twin visual alarm indicator (LED's) "Blink" in stand by and "steady" in alarm complete in all respects.

Heat detector : providing & fixing of heat detector based on heat rate-of- rise/fixed temperature with working voltage 9-33V DC twin visual alarm indicator (LED's) "Blink" in stand by and "steady" in alarm complete in all respects.

Manual call point: Providing & fixing of manual calls point flush or surface mounting. Front protection glass cover. Unbreakable glass ABS plastic body.

Internal hooter: Providing &fixing of internal hooter with working AC Voltage 220V A.C./24V D.C. current consumption, sound output 120 DB, material M.S. sheet.

Supply of XLPE insulated 1.5 sq. mm. Armoured 2 core FRLSZH fire alarm cable (RED) Fire Survival Cable conforming IS-7098 (Part-1) 1988, 1100 Volt grade, 2/3/4/8/10/12 core ISI marked with copper stranded/solid conductor.

Supply, installation, testing and commissioning of 240W power amplifier with 100,70V speaker op, combination XLR/RCA line in line out connectors. Speaker OP short circuit protection.(with require mounting arrangement)

Supply, installation, testing and commissioning of 6W ceiling speaker with max SPL1M/1W 96dB. Frequency response of 80Hz-20KHz with a dispersion angle of 160 deg. The speaker should have tapings at 6W/3W/1.5W (with require mounting arrangement)

SITC of 3200 Ansi Lumens Projector with technology : Digital Line Processing Min Brightness : 4200 Ansi Lumens Min Contrast Ratio 3000:1 Image Size 0.78 - 9.38m (30.79" - 369.43") Diagonal 4:3 Native resolution : XGA (1024 x 768) Video Compatibility : PAL, Secam 576 i/p NTSC 480 i/p, HD 720p/1080i/1080p Aspect ratio Native 4:3 Compatible 16:9 Power supply 100 - 240V, 50-60Hz. (Make : Optoma/Infocus/LG)

Supply, Installation, Testing & Commissioning of Mounting arrangement for projector.

Supply, Installaton, Testing & Commissioning of Motorised Projector Screen - 6 x 4 Matt White, 220 V Make : Liberty/Suvira/Elite

Providing, Laying and Installation of HDMI Cable.

Providing & Laying of 2-core 2.5 sq. mm. Shielded Twisted pair loudspeaker cable. Make : Liberty/Finolex/Lapp

Providing & Fixing of 55" LED Display (pane) with Screen size : 55" Aspect ratio - 16: 9, Resolution 1920 x 1080 , Panel Type :IPS Brightness Time : 12ms , Viewing Angle : 178 x 178 deg. , Audio power : 20W (10W x 2 ) for External Speaker

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with alu. stranded /solid conductor : Armoured- 2.5 Sqmm 3 Core

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with alu. stranded /solid conductor : Armoured- 6.0 Sqmm 4 Core

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with alu. stranded /solid conductor : Armoured- 10.0 Sqmm 4 Core

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with alu. stranded /solid conductor : Armoured- 16.0 Sqmm 4 Core

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with alu. stranded /solid conductor : Armoured- 25.0 Sqmm core/3½

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with alu. stranded /solid conductor : Armoured- 35.0 Sqmm core/3½

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with alu. stranded /solid conductor : Armoured- 50.0 Sqmm core/3½

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with alu. stranded /solid conductor : Armoured- 95.0 Sqmm core/3½

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with alu. stranded /solid conductor : Armoured- 150.0 Sqmm core/3½

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with alu. stranded /solid conductor : Armoured- 240.0 Sqmm core/3½

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with alu. stranded /solid conductor : Armoured- 400.0 Sqmm core/3½

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with copper stranded /solid conductor : Armoured core- 2.5sqmm 3 Core

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with copper stranded /solid conductor : Armoured core- 6.0 Sqmm 4 Core

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with copper stranded /solid conductor : Armoured core- 10.0 Sqmm 4 Core

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with copper stranded /solid conductor : Armoured core- 16.0 Sqmm 4 Core

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with copper stranded /solid conductor : Armoured core- 25.0 Sqmm core/3½

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with copper stranded /solid conductor : Armoured core- 35.0 Sqmm core/3½

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with copper stranded /solid conductor : Armoured core- 50.0 Sqmm core/3½

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with copper stranded /solid conductor : Armoured core- 95.0 Sqmm core/3½

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with copper stranded /solid conductor : Armoured core- 150.0 Sqmm core/3½

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with copper stranded /solid conductor : Armoured core- 240.0 Sqmm core/3½

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with copper stranded /solid conductor : Armoured core- 400.0 Sqmm core/3½

55 inch panel 4K Display Naïve Resolution -3840x2160 (UHD) 4K Brightness-Minimum 300cd/m2 or above, Contrast Ration(Native) minimum 1300:1 or better, viewing angle 178*178, Response time 9ms or better. Input ports- HDMI-3, USB 2.0-1, RS 232C-1, RJ45-1, Smart Share / Screen share, SNMP support to take control of display, wake on LAN, Build in Quad core media player. Audio- 20w (10wx2) Power supply- 100-240V, 50/60H2 Make-LG, Samsung, equivalent.

65 inch panel 4K Display/T.V. Panel- Naïve Resolution -3840x2160 (UHD) 4K Brightness-Minimum 300cd/m2 or above, Contrast Ration(Native) minimum 1300:1 or better, viewing angle 178*178, Response time 9ms or better. Input ports- HDMI-3, USB 2.0-1, RS 232C-1, RJ45-1, Smart Share / Screen share, SNMP support to take control of display, wake on LAN, Build in Quad core media player. Audio- 20w (10wx2) Power supply- 100-240V, 50/60H2 Make-LG, Samsung, equivalent.

LCD Projector DW832/ equivalent 5000 ANSI lumens of brightness and 15000:1 contrast ratio for clear, crisp and bright projection, great flexibility with 1.5xzoom, 2xHDMI input for high definition content with the same high quality, 10w speaker and microphone input., 3D comptibility with DLP® Link.

LCD Projector DS262/ equivalent high 3500 ANSI lumens of brightness and 15000:1 contrast ratio, 6 segment colour wheel for improved and vivid Colour reproduction, Audio ready with 2 watt audio speaker, 3D compatibility.

Screen 6'x4' size manual

Screen 8'x6' size moterized (NOTE:- The bidder shall quote his own rates for Item No. 1 to 230 of Item rate Part.)

ABBOTTSONS IMPEX PVT LTD

CHATURLAL CONTRACTOR

HIMALAYA TRADERS

IMPRESSION FURNITURE INDUSTRIES PRIVATE LIMITED

Creating Space Private Limited

Methodex Systems Pvt. Ltd

BONTON TECHNOMAKE PRIVATE LIMITED