REPLACEMENT OF ROOF SHEETS FALSE CEILING PARTICLE BOARDS WITH ASSOCIATED B/R WORKS UNDER PH III UL DAHUNG DUM DUM NALA MH MES OFFICES AND MESSES OF AGE B/R UNDER GE TENGA

Amount

Dismantling plain or corrugated steel sheeting of any thickness as in roof coverings complete all as specified and directed.

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering cladding to wall, fixed with self tapping screws as specified.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

M&L for preparation of old steel painted Surfaces of any description, over 10cm in width or girth,not otherwise described and applying one coat of synthetic enamel paint all as specified and directed.complete all specified and directed

M & L for Preparation of new or previously untreated steel surface and applying two coat of synthetic enamel paint over a coat of red oxide primer to steel and iron surfaces of any description over 10 cm in width or girth not otherwise described including preparation of new steel surfaces.

Material and labour for preparation of old distempered surface of walls and applying one coat of oil bound distemper all as specified and directed.

M&L for 3mm thick one coat of wall care putty on wall all as specified and directed.

Material and labour for washing rubbing down and scrapping of distempered and painted surfaces applying two coat of oil bound distemper all as specified and directed

Dismantling structural steel work in cluding doors, gates but excluding framed truss etc.

S&F of rolled mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-290(Gde-E-165)

M&L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161 1979 grade St.-240

M & L for Preparation of new or previously untreated steel surface and applying two coat of synthetic enamel paint over a coat of red oxide primer to steel and iron surfaces of any description over 10 cm in width or girth not otherwise described including preparation of new steel surfaces.

Demolition of cement concrete in floors n.exc 15 cm thick in ground floor (below or above ground level) and in any position all as specified

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggragate as in subbase 40 mm thick complete all specified and directed by engr in charge.

M&L for 15 mm thick screed bed in CM 1:6 for laying floor tiles.complete all specified and directed

M&L for Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all specified and directed

M&L for Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all specified and directed

M&L for Non-skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding .11 sqm,in floors etc set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade.

M&L for Non-skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding .38 sqm, in vertical surfaces etc set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over 15mm screed bed with CM 1:6 in Kitchen platform complete all specified and directed

M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry on wall/ floor and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises.

M & L for 10mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces finished rough to receive tiles .

M & L for Glazed coloured ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match.

Dismantling timber framed work scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section in any position complete all as specified.

Dismantling timber framed work scantlings in fillets, rails, posts, rafters, purlins, etc. over 40 sq. cm in section in any position complete all as specified.

M&L 2nd class hard wood in scantling clean swan timber framed and fixed as directed.

Dismantling boarding, any description, fixed in any position with nails,shelves,racks etc.

M&L for 12mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber frame work

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps (when open) in 40mm complete all as specifird and directed.

Sypply & Fixed 15 mm thick 2nd class hard wood clean swan with butt joints in shelves; Partitions and shelves of built-in cupboards, almirahs, book cases, toilet boxes, racks, pelmets and similar work.

Dismantling of wall and ceiling board or insulation boards/slabs/blanckets/any thickness including cover fillets

S&F of Solid / hollow PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing

S&F of 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

S&F of PVC insulation panels 10mm thick with EPS stuck to 1mm printed PVC sheet suitably placed in false ceiling grid made of Aluminium/G.I./M.S. as per specification and drawing

S&F of Anodised aluminium snap grid frame work for false ceiling all as specified

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 Sqm but not exc 4 Sqm.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sqm

S &F of Powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, hinges, Floor spring, door stoper anodised aluminum snap beading screws etc with complete all as specified and directed by Engr-in-Charge.

S&F Powder coated Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws two number of rollar in each shutter etc with complete all as specified and directed by Engr-in-Charge.

S&F Powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F of Plain Aluminium composite panel 04 mm thick with powder/Rough PVDF coatted, anti bacterial and fire Proof any colour suitable for exteriar and interiar with complete all as specified and directed by Engr-in-Charge.

Demolition of brick/stone boulder masnory block walling built in cement mortor

M&L PCC 1:3:6 type C1 as in block masonry with solid blocks exc 10 cm in width and set in CM 1:6.complete all as specified and directed

M&L rendering 15 mm thick onbrick or concrete block masonry in CM 1:6 complete all as specified and directed

Taking down of cement or cement lime plaster/tile work any description from brick or stone wall etc. including raking out of joints, hacking for key, scrubbing down with water etc.

M&L rendering 15 mm thick cement plaster on external surface in CM 1:6 on brick & concrete surfaces and finished even and smooth (without using extra cement) all as specified and directed.

M & L for preparation of new external plasterd surface of wall and ceiling apply of birla white putty, make the surface smooth by rubbing with emary paper and applying two coats of weather proof paint complete all as specified and directed ( Make : Appex of Asian Paint or equivalent of J & N/ Berger/Narolac)

M&L for preparation of new plastered surfaces of wall any description over 10cm girth or width, not otherwise describedand and applying two coats of plastic emultion paint complete all specified and directed by engr in charge

S & F 100mm size mild steel butt hinges medium weight cold rolled and fixed.

S & F 75mm size mild steel butt hinges medium weight cold rolled and fixed.

S& F Aluminium anodised barrel tower bolts 150mm long of extruded section and fixed

S& F Aluminium anodised barrel tower bolts 100mm long of extruded section and fixed

S & F 150mm size extruded aluminium alloy handles, fabricated type anodised

S & F 100mm size extruded aluminium alloy handles, fabricated type anodised

S&F aluminium alloy, anodised, sliding door bolts 300mm size with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed

S&F for Elephant shield tape 100mm width Multi application Reinforcement fabric, UV Stabilized & Hydrophilic for water froofing to roof / crack Patch / Wall Repair / Fibre wall coating suitable of all types of roof sheet , Water storage tanks and walls etc and similar work complete all as specified and directed.

S&F in repairs 4.8 mm thick sheet glass with 50 micron solar control film reflective type, ordinary quality and glazing with oil putty or wooden beat in each pane complete all as specified and directed.

All as per item No. 58 above but exc 0.50 Sqm in each.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M/S ASHOK CONSTRUCTION (BID ID -3167230)

M/S DARGEY KOMU ENTERPRISES (BID ID -3167344)

M/S DOLKO ENTERPRISES BOMDILA (BID ID -3167373)

M/S KUNKAPU ENTERPRISES (BID ID -3167294)

mon traders (BID ID -3167279)

M/S MURPHEW ENTERPRISES (BID ID -3167315)

M/S R D TRADERS (BID ID -3167333)