REPLACEMENT OF LT BARE CONDUCTOR BY ABC IN THE ARE OF D BLOCK SECTOR 47 NOIDA UNDER EUDD V NOIDA

Amount

FOLLOWING WORK REPLACEMENT OF LT BARE CONDUCTOR BY AERIAL BUNCHED CONDUCTOR (3x120+1x95+1x16 SQ.MM.) AND OTHER NECCESSARY SYSTEM STRENTHNING WORK IN THE AREA D BLOCK SECTOR-47 NOIDA WILL IMPROVE RELIABILITY OF SUPPLY & AVOID UNWANTED INTERRUPTIONS IN THE AREA. :-

Cartage of ST poles 11 mtr long from ESC Noida/Sahibabad/ Ghaziabad /Any other ESC of Meerut Discom to JE Store and from JE store to various points of site of work including loading and unloading at both ends.

Cartage of other line material such as M.S. Eathing Rod 20x2500 mm. (with 40mm taper extra) from ESC Noida/Sahibabad/Ghaziabad /Any other ESC of Meerut Discom to JE Store and from JE store to various points of site of work including loading and unloading at both ends.

Cartage of other line material such as Stay Complete from ESC Noida/Sahibabad/Ghaziabad /Any other ESC of Meerut Discom to JE Store and from JE store to various points of site of work including loading and unloading at both ends.

Cartage of other line material such as Insulated ABC of 3x120+1x95+1x16 Sq.mm. from ESC Noida/Sahibabad/Ghaziabad /Any other ESC of Meerut Discom to JE Store and from JE store to various points of site of work including loading and unloading at both ends.

Cartage of other line material such as LT XLPE Cable Al. 3.5x400 Sq.mm. from ESC Noida/Sahibabad/Ghaziabad /Any other ESC of Meerut Discom to JE Store and from JE store to various points of site of work including loading and unloading at both ends.

Cartage of other line material such as LT XLPE Cable Al. 1x400 Sq.mm. from ESC Noida/Sahibabad/Ghaziabad /Any other ESC of Meerut Discom to JE Store and from JE store to various points of site of work including loading and unloading at both ends.

Providing & fixing Stone Pad 300x300x75 mm.

The Excavation of foundation pit in CC road/ mix soil/ normal soil/ soft & hard rack by using heavy duty compressor and its back filling and leveling etc. The size of the pit will be 600x600x1800 mm for each pole and having a depth of 1/6 of the full length of the support.

Erection of Single support on 11 Mtr. long ST Pole for LT line including fixing of all accessories of LT line as per RESPO schedule Complete in all respects.

Grouting of each pole (In ratio of 1:4:8 in Cement, sand and Brick Ballast) in size 450mmx450mmx1800 mm as per RESPO schedule Complete in all respects.

Construction of Plinth in size 450x450x300 mm of each (0.285 Cum) pole above the ground level (In ratio of 1:3:6 in Cement, sand and Brick Ballast) as per RESPO schedule Complete in all respects.

Excavation of earth and driving of M.S. earthing rod of size 20x2500 mm (with 40 mm. taper extra) in earth and jointing through G.I wire of 6 SWG between support and earth electrode by providing proper size of bolts and nuts etc. as per RESPO schedule Complete in all respects.

Grouting & Concreting of stay rod 1800x16 mm complete in all respect as per RESPO schedule Complete in all respects.

Fixing, Tighting and nozzling of stay wire with the pole of required tension with clamps as per RESPO schedule Complete in all respects.

Laying Lifting and final Binding, Sagging of Insulated ABC of 3x120+1x95+1x16 Sq.mm. including fixing of all accessories as per RESPO schedule Complete in all respects.

Laying of LT XLPE Cable Al. 3.5x400 Sq.mm. including fixing of all accessories as per RESPO schedule Complete in all respects.

Laying of LT XLPE Cable Al. 1x400 Sq.mm. including fixing of all accessories as per RESPO schedule Complete in all respects.

Providing of LT Distribution Box suitable for above LT line after inspection of competent committee at manufacturing site of the items with actual guarantee period.

Fixing of above Distrubution Boxes/ Kiosk on the LT poles including all clamps & material required for mounting, connections & sealing complete in all respect.

Providing & Fixing of Dead End clamps (Insulated) with bolts & nut.

Providing & Fixing of Dead End I-Hook (Insulated) for above clamps with bolts & nut.

Providing & Fixing of Suspension clamps (Insulated) with bolts & nut.

Providing & Fixing of Suspension clamps I-Hook (Insulated) for above clamps with bolts & nut.

Providing & Fixing of 95/50 Sq.mm. - 70/35 Sq.mm. (For line to line jumpering & energiizing DB neutral) PG Clamps with bolts & nut.

Providing & Fixing of Pole Clamps with bolts & nut suitable for STP.

Providing & Fixing of L.T. Insulation Piercing Connectors of 120-50 Sq.mm. - 50-35 Sq.mm. size for energizing distribution kiosk/box with bolts & nut.

Providing & Fixing of L.T. Insulation Piercing Connectors (16 Sq.mm. - 16 Sq.mm.) suitable for street light connection with bolts & nut.

Providing & Fixing of Mid span jointing sleeves (120 Sq.mm.) with bolts & nut.

Providing & Fixing of Aluminium crimping lugs 120/95 Sq.mm suitable for above work.

Providing & Fixing of Stay Clamps with bolts & nut.

Providing of 1x35 mm2 XLPE/ PVC Insulated Al. Cable for energising the distribution boxes/ Kiosks after inspection of competent committee at manufacturing site of the items with actual guarantee period..

Fixing/ Laying of 1x35 mm2 XLPE/ PVC Insulated Al. Cable for energising the distribution boxes/ Kiosks including fixing of all accessories as per RESPO schedule Complete in all respects.

Providing & Fixing of MS Bolts with Nuts

Providing and installation of 400 Amp. ACB, (Make L&T, Schneider, ABB, Hevell's) after inspection of competent committee at manufacturing site of the items with actual guarantee period:-

400 amp. 03 pole fixed manual ACB.

Red/yellow/blue light indication

ON & OFF Indication

Amp., Volt meter& energy meter digital

Metering C.T 400/5A,

Panel fabrication of size 1250mm x 900mm x 600 mm made of M.S sheet 14 gauge with powder coating with panel lock and key arrangement.(two nos). and additional locking arrangement seprately including providing hut type shape as per drg.

Fabrication of aluminium bus-bar for each phases

Incoming size 425 mm x 50mmx12 mm (twin)

Out going size 720 mm x 50mm x 12 mm(twin)

Neutral size 900mmx50mmx12 mm.

Fabrication of pannel stand made of M.S Angle of size 900mm x 600mm x 500 mm as per drg.

Assembly of above ACB, Indicators, Meters, Metering CT & bus bar arrangment in the panel, fitting the panel on Stand with nut and bolts with wiring etc. & grouting in ratio 1:4:8 with cement, coarse sand and brick blast.

Providing and fixing of aluminium bus bar of size 300mmx60mmx12 mm on L.T side of T/F.

Making all connections with ACB & Distribution T/F and commissioning the ACB complete in all respect.

Water level earthing of ACB with M.S. earhting strips of best quality (ISI mark) as per RESPO norms complete in all respects. (All material wiil be provided by the contractor for Earthing)

Providing and fixing of Pad Lock for locking arrangement of LT Distribution Boxes/Kiosks.

Providing and fixing of MS Clamps for LT Distribution Boxes/Kiosks with nuts & bolts.

Disconnecting of LT service line of following category of consumers before dismantling of old LT line and the reconnections through distribution boxes/kiosk, supply & fixing of Clamp/Connectors etc for Consumer Service Cables after commissioning of ABC line.

Single Phase

Three Phase

Dismantling of LT line 3/4/5 wire including rolling back its conductor, wire, clamps, insulator etc. including stacking.

Cartage of above dismantled of LT line 3/4/5 wire in rolling back its conductor, wire, clamps, insulator etc. including stacking and transportation of material to the discom stores within the same town.

Dismantling of bam & rusted ST pole.

Cartage of dismantled of bam & rusted ST pole from site to JE store / central store & proper stacking with loading & unloading.

Providing & fixing of H.T. Tape.

Providing & fixing of PVC Tape.

Resagging of existing 11 KV Line of feeder no. 9 emanating of 33/11 KV S/s Sector-47, Noida in both side spans. (Approx 2.0 Kms. line)

Providing & fixing Guarding of above exisiting 11 KV Line of feeder no. 9 emanating of 33/11 KV S/s Sector-47, Noida by suitable GI wire as per RESPO norms complete with all respects. (Approx 2.0 Kms. line)

REPAIRING WORKS OF EXISTING 06 NOS. DAMAGED FENCING OF 11/0.4 KV L.T. SUB-STATION INSTALLED AT VARIOUS PLACES AS PER FOLLOWING :-

Reparing of damaged wiremesh fencing/frames as per site requirement complete with all respects with painting of LT Sub-stations. (All Material provided by contractor for above work.)

Reparing of damaged boundry / toe wall by brick/cement work including plaster and finishing with water proof cement paint for each fencing of LT Sub-stations as per site requirement. (All Material provided by contractor for above work)

Welding of damaged/rusted existing ST Pole in H.T./L.T line by providing M.S Angle and plintihing also.

Repairing of broken/badly damaged S.T Poles (damaged at ground level) in existing H.T/L.T lines due to extra ordinary rusting & scaling. From bottom side welding of 4/5 pieces( approx 75 cm. long) of angle iron of size 50x50x6 mm. Ist of all digging of pit around the pole of size 1.0 mtr. x 1.0 mtr. x 1.0 mtr. is to be done and then cleaning of rust & de-scaling with the help of hard wire brush & chisel and then MS angle iron of size 50x50x6 mm in 4/5 pcs. of required length as per site requirement varying from 70 cms to 75 cm to cut down and then to be welded with the healthy top and bottom portion of the pole with Ist class electric welding with own welding generator set in such as way that on top of bottom potion over-lapping of healthy part is covered 200 mm length approx. before welding the poles where top & bottom portion are separated, the same are to be kept in alignment safely & after completing the above work, the pit should be refilled. Concreting of S.T Pole for grouting (0.285 cu mt.) cement, stone blast) Making plinth of above repaired ST pole in round shape of height 0.30 meters from ground level having outer dia of 500 mm size in CC 1:3:6 in cement, sand , Stone ballast etc. and completer the work in all respect.

Reparing of existing 06 Nos. 11/0.4 KV S/S T/F plinth at various places as per site requirement, material provided by the contractor at his own cost complete in all respects.

Providing & fixing of interlocking for path (approx 5x10 Sq.Feet) existing 06 nos. 11/0.4 KV S/Ss fencing Gate to T/F Plinth and ACB Panel at various places as per site requirement, material provided by the contractor at his own cost complete in all respects.

Providing of M.S. earthing rod of size 20x2500 mm (with 40 mm. taper extra) for existing STP.

Excavation of earth and driving of above M.S. earthing rod of size 20x2500 mm (with 40 mm. taper extra) in earth and jointing through G.I wire of 6 SWG between support and earth electrode by providing proper size of bolts and nuts etc. as per RESPO schedule Complete in all respects.

Repairing work of existing grouting and plinth of each pole (In ratio of 1:4:8 in Cement, sand and Brick Ballast) in size 450mmx450mmx1800 mm in L.T./ H.T. Line as per RESPO schedule Complete in all respects.

Water level earthing of existing 400 KVA transformer (body and neutral) with M.S. earhting strips of best quality (ISI mark) as per RESPO norms. (All material wiil be provided by the contractor for Earthing)

Removal of damaged conductor from existing HT lines with making bundles in coil shape & cartage of material from site of work to J.E's Store with loading & unloading at both ends. (Approx 0.5 Kms. line)

Re-laying lifting, stringing & proper sagging of new conductor in place of old and damaged removed conductor on above existing H.T line with binding, jumpering etc. including cartage, loading & unloading from received back site material to site of work. (Approx 0.5 Kms. line)

Cutting and chopping of tree branches on the H.T./ L.T. in 9 Kms line route.

Providing and fixing of HT Danger Board with clamp

Providing and fixing of Number Plate

ANJNI TRANSFORMER AND SWITCH GEARS

PACHOURI ELECTRICALS

M/s Ashu Brothers