REPAIR TO SEEPAGE LEAKAGE ROUTINE BR MAINT WORKS AND PERIODICAL SERVICES IN NEW MH AT BAIRAGARH UNDER GE BHOPAL

Amount

Taking down cement plaster on brick or stone wall etc including raking out joints, hacking for key, scrubbing down with water or cement lime plaster any description, complete all as specified and directed.

M&L for rendering 20mm thick in two coats of 10mm thick each on faces of brick work or concrete surfaces; first coat (rendering coat) in cement mortar 1: 6 and second coat (finishing coat) in cement mortar 1: 4 mixed with water proofing compound (water proofing compound to be measured separately as supply only) and finished fair and even complete all as specified and directed.

Supply only Integral water profing compound, complete all as specified and directed.

M&L for applying high Granular textured finish paint over and including one coat of primer as per manufactures instructions complete all specified and directed . NOTE:- (i) Texture finish shall be applied by texture roller to produce high profile texture finish. (ii) Make of Granular textured finish paint:- Asian or equivalent in Dulux/Nerolac as approved by Engineer-in-charge. (iii) 3mm thick wall care cement putty where ever required shall be measured & paid separately.

M&L for vertical surface expansion joint treatment as per the following sequence, complete all as specfied and directed.:- (i) All surfaces should be clean, dry, free from grease, oil or dust and any contaminants that could harm bonding. (ii) Remove old sealant residue completely before applying new sealant with wire-brushing the internal sides of the concrete where the sealant is to be applied. (iii) Joint edges, If spalled, it should be rectified properly with PMM by using Dr. Fixit Pidicrete URP/STP Ltd/Equivalent approved by GE in the ratio of 1:5:15. Filling. (iv) Wirebrushing the top surface of the concrete upto atleast 200 mm on either side of the expansion joint. (v) Allow the substrate to dry after degreasing.

Providing and fixing the polyethylene joint backing rod 30 to 50 mm dia as a backup material into the expansion joint leaving adjust width to depth ratio and falling of sealant while application top of the slab. Fix a masking tape on both sides of joint surface to get neat & clean appearance of joints after application of sealant, complete all as specified and directed.

Providing and apply Dr. Fixit Pidiprime A or equivalent on two sides of the properly prepared joint surface by brush and allow it cure for minimum 20 minutes before filling the Dr. Fixit Pidiseal 43G/41P Poly Sulphide Sealant (PSS) /Equivalent for joint width upto 50mm. Providing and filling PSS in joint upto width of 50 mm and depth of 20-25mm. Immediately clean up any excess sealant with a solvent from M/s Pidilite Industries having elongation of 500% into for 25 mm (w) x 12 mm mm deep Depth shall be 2:1 (half) upto the surface of the slab. As per as per the technical specification of manufacturer & consultant, complete all as specified and directed.

Fixing only in repairs aluminium sheet screwing it at every 300 mm distance on either side of the sheet, complete all as specified and directed.

M&L for dampness rectification in toilet area/corridor area filling Tile Joints with epoxy grout. Clearing all tile joints with grinder and removing existing cement grout, cleaning the surface to remove all foreign material applying masking tape around to joints filling Tile joints with epoxy grout removing the tape & cleaning tiles with thinner & acid to make it stain free, complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons, walls, etc, laid bedded and pointed in any mortar complete all as specified and directed.

M&L for water proofing treatment to sunken surfaces of slab in following sequence complete all as specified and directed. :- (a) Slope correction providing PCC 1:1.5:3 using 12.5mm graded stone aggregate, average thickness 25mm, mixed graded styone aggregate, average thickness 25mm, mixed with integral water proffing compound "DITCHTMENT DM' manufactured by Dr fixit Pidiproof LW + of M/s Pidilite Industries or STP No 1 (Liquid) of M/S STP Ltd as approved by GE, in proportions as suggested by manufacturer. (b) Applying evenly a priming coat of bituminous primer confirming to IS 3384 @ 0.7 KG per SQM on prepared surfaces. (c) Applying evenly a coat of hot blown bitumen of grade 85/25 @ 1.5KG/SQM on the primer surfaces. (d) Laying 150 micron thick black polythence film on the suface with 10mm overlaps sealed and bounded the surface. (e) Applying evenly a coat of hot bown of grade 85/25 @ 1.5 KG per SQM on the surfaces. (f) 48 hrs testing of treatment for water thightness by ponding of water.

M&L for Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 15mm thick screed bed in CM 1:4 complete all as specified and directed. [MAKE: SOMANY/KAJARIA/ORIENT]

M&L for Glazed ceramic coloured tiles 300mm x 200mm x 7mm thick, in vertical surfaces such as skirting, dados and risers to steps, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 10mm thick rendering in CM 1:3 complete all as specified and directed.[MAKE: SOMANY/KAJARIA /JOHNSON/ORIENT]

M&L for dampness rectification on Wall Area in following sequence complete all as specified and directed :- (i) Surface Preparation : Removing existing putty/plaster/POP surface from the affected wall with wire brush/grinder/hammer etc up to brick level. (ii) Coating : Applying two coats of Dr Fixit Pidifin 2k/Equivalent (a two component, anti-fungal, acrylic waterproofing coating) over cleaned surface with brush. And allowing it to dry for 24 hours. (iii) Finishing the surface : Applying plaster & putty over the treated surface with waterproofing compound mixed with putty & plaster to provide proper finish after that painting can be done after proper curing.

Taking up or down 15mm bore GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified.

S&F 15mm GI tube medium grade with all necessary fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed. (Make-TATA/SURYA/JINDAL/PRAKASH)

Taking up or down 20 mm bore GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

S&F 20 mm GI tube medium grade with all necessary fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed. (Make-TATA/SURYA/JINDAL/PRAKASH)

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth, complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1: 6 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 10mm thick rendering in cement mortar 1:3 on concrete surfaces as in ceiling including finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for vitrified light shade flooring tiles, 10 mm thick (Square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, laid in floors, etc set and jointed in neat cement slurry and pointed in epoxy adhisive (Make :Dr.Fixit or Balendura) to match the colour of tiles with & including 15mm thick rendering in CM 1:4 complete all as specified and directed. [MAKE: SOMANY / KAJARIA / NITCO]

M&L for vitrified light shade tiles, 10 mm thick (Square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, as in vertical surfaces such as skirting, risers to steps, etc set and jointed in neat cement slurry and pointed in epoxy adhisive (Make :Dr.Fixit or Balendura) to match the colour of tiles with & including 10mm thick rendering in CM 1:3 complete all as specified and directed. [MAKE: SOMANY / KAJARIA / NITCO]

M&L for 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including grinding, moulding and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for rounding to edges of stone one edge such as in steps, cooking platform and other similar situation, complete all as specified and directed.

M&L for Machine cut Kota stone slab flooring 20-25mm thick (size not less than 450mm x 600mm) with and including 20mm thick cement screed base in CM 1:3, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing complete all as specified and directed.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar, etc with and including 10mm thick rendering in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing complete all as specified and directed.

Taking up or down 25 mm steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed.

S&F GI tube medium grade 25 mm bore with all fitting and fixed complete to wall & ceiling or laid in floor, complete all as specified and directed.

M&L for cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 20 cm girth, complete all as specified and directed.

S&F in repairs sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, including CP waste coupling and 32mm dia PVC waste pipe of suitable length complete all as specified and directed. [MAKE:- Prayag (Cat No.1216 Gloss) or equivalent in NIRALI/BLUE STAR as approved by GE]

S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8602) or equivalent in JAGUAR/MARC as approve by GE]

S&F in repair 15 mm Bib taps, fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixing complete all as specified and directed by engr in charge. (MAKE-PRAYAG( CAT NO 8606) OR EQIVALENT IN JAGUAR/MARC AS APPROVED BY GE)

S&F 15 mm stop valves, cast copper alloy, chromium plated screwed down high pressure, with crutch or butterfly handle, scrwed both ends for iron pipe or for unions and fixing complete all as specified and directed by engr in charge. (MAKE-PRAYAG (CAT NO 8328) OR EQIVALENT IN JAGUAR/MARC AS APPROVED BY GE)

S&F in repairs 15mm bore stop cock, cast copper alloy chromium plated with long shank and cut (concealed type) screwed down , screwd for iron pipe or union and fixed in repair complete as specified and as directed. (MAKE-PRAYAG / OR EQIVALENT IN JAGUAR/MARC AS APPROVED BY GE)

S&F in repairs 15 mm pillar taps, fancy type chromium plated,with extended lever handle and wall flange elbow operated fixing complete all as specified and directed by engr in charge. (MAKE- JAGUAR Cat no. FLR-CHR-5031N /MARC or equivalent AS APPROVED BY GE)

S&Fin repair 15 mm Bib taps, fancy type chromium plated with extended lever handle and wall flange elbow operated fixing complete all as specified and directed by engr in charge. (MAKE- JAGUAR Cat no. FLR-CHR-5043N /MARC or equivalent AS APPROVED BY GE

S&F in repair brass chromium plated shower rose 125mm in size with or without swivel joints any size incl fixing to steel pipe or union , complete all as spfecified and directed.

S&F in repairs 20mm dia (Curtain rail) mild steel chromium plated fancy type with fixing brackets, stops, rollers etc complete all as specified.

Taking down chowkhats or frame with shutter n.exc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed

S&F steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete including lugs with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F steel windows with side hung shutters including box type hinges with steel handle, and peg stay, complete with wire gauzed bar, dovetailed or welded complete all as specified and directed.

M&L framed work such as grills, gratings, gate etc with ends of bars souldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railing, frame work of water tanks and similar work conforming to Fe-290, Gde E-165 complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc .50 sqm in each pane, complete all as specified and directed

S&F 3 mm thick figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane, complete all as specified and directed.

S&F steel ventilator with top hung shutters including hinges with fixed type MS handles peg stay and tower bolt but with additional sash bars MS flats for fixing of wire gauge complete all as specified and directed.

S&F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperure 1.40 mm and fixed and with stainless steel wire staples fixed complete all as specified and directed.

Taking down door shutter of any description exc 1.0 sqm but n.exc 2.00 sqm each, complete all as specified and directed.

Taking down chowkhats or frame with shutters exc 1.5 sqm but not exc. 4.00 sqm each (without taking off shutters from the frame) complete all as specified and directed

S&F Factory made solid PVC moulded door shutter with particle board core 28 to 30mm thick (style) with 2, 4 or 6 raised panel design with 2mm thick 3D plain colour PVC sheet on the front face and 2 mm plain colour PC sheet on back face complete all as specified and directed. [MAKE:-M/s RAJSHRI PLASTIWOOD / M/s SINTEX INDUSTRIES / M/s POLY WINDOWS / M/s DURA PLAST / / M/s ACCUCELL]

S&F Pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, with & including filing of cement concrete typ B-0, 1:2:4 using 12.5mm graded stone aggregates inside frames complete all as specified and directed.

S&F Pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, with & including filing of cement concrete typ B-0, 1:2:4 using 12.5mm graded stone aggregates inside frames complete all as specified and directed.

M&L for factory made, second class hardwood 35mm thick plain, framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers complete all as specified and directed.

M&L for factory made second class hardwood glazed and skeleton door shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete all as specified and directed.

S&F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail panel will be of stainless steel wire gauze which shall be wrapped on an additional 8 mm square M.S. Solid tube and this tube shall be welded to 19mm x 19mm M.S. tubes. The G.I. wire gauge shall be stretched to tighten firmly complete all as specified and directed. [MAKE:-M/s RAJSHRI PLASTIWOOD / M/s SINTEX INDUSTRIES / M/s POLY WINDOWS / M/s DURA PLAST / / M/s ACCUCELL] NOTE:- Wire gauge shall be measured and paid separately.

S&F 100 mm but hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type B-21 complete all as specified and directed.

S&F 150 mm Aluminium handles, cast type, anodised complete all as specified and directed

S&F 150mm Aluminium anodised barrel tower bolts extruded section and fixed complete all as specified and directed.

S&F 200 mm Aluminium anodised barrel tower bolts extruded section and fixed complete all as specified and directed

S&F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed

S&F in repair mortice latch 4 levers vertical type size 100mm, complete all as specified and directed

M&L preparatration of new surfaces of wall including brooming, scraping down smoke spot, moulds, moss, effloresecent salts trading oil, greasy spots and stopping nails marks and applying two coat of cement base paint complete all as specified and directed.

M&L for preparation of newly plastered or unplastered surfaces of walls and applying two coats of oil bound distemper complete all as specified and as directed.

M&L preparation of old decorated surfaces of wall including brooming, scraping down smoke spot, moulds, moss, effloresecent salts trading oil, greasy spots and stopping nails marks and applying one coat of Oil emulsion distemper, complete all as pecified and directed. Note : Required scafolding is included for painting at any height

M&L for Preparing old decorated plastered or unplastered surfaces of walls and applying one coat of exterior acrylic emulsion paint, white or tinted complete all as specified and directed. Note : Required scafolding is included for painting at any height

M&L for Preparing old decorated plastered or unplastered surfaces of walls and applying one coat of cement base paint, white or tinted complete all as specified and directed. Note : Required scafolding is included for painting at any height

M&L preparatration of old decorated surfaces of wall including brooming, scraping down smoke spot, moulds, moss , effloresecent salts trading oil, greasy spots and stopping nails marks and applying two coat of white wash on wall complete all as pecified and directed.

M&L preparatration of old decorated surfaces of ceiling including brooming, scraping down smoke spot, moulds, moss , effloresecent salts trading oil, greasy spots and stopping nails marks and applying one coat of white wash on ceiling complete all as pecified and directed.

M&L for preparation old painted steel & iron surfaces of any description over 10cm in width or girth and applying one coat of synthetic enamel paint, complete all as specified .

M&L preparatration of old decorated surfaces of wall including brooming, scraping down smoke spot, moulds, moss , effloresecent salts trading oil, greasy spots and stopping nails marks and applying two coat of Anti bacterial, Anti fungus paint complete all as pecified and directed.

M&L for preparing new surfaces of wood and wood based materials of any description over 10cm in width or girth and applying two coat of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

S&F in repairs Ball brass valves, ISI marked, high pressure, with polythene float and fly nut, screwed for iron pipe or brass ferrule 20 mm bore complete all as specified and directed. [MAKE:-SANT / LEADER / RAMCO / ZOLOTO/PRAYAG]

S&F in repairs Ball brass valves, ISI marked, high pressure, with polythene float and fly nut, screwed for iron pipe or brass ferrule 15 mm bore complete all as specified and directed. [MAKE:-SANT / LEADER / RAMCO / ZOLOTO/PRAYAG]

S&F in repair Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 25 mm bore complete all as specified and directed. [MAKE:-SANT / LEADER / RAMCO / ZOLOTO]

Demolition to cement concrete in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 50 mm dia UPVC pipe as in water spout at the lowest point of sunken floor with 600 mm projection beyond the outer face of the wall with outer end cut in chamfered angle for easy drain of water complete all as specified and as directed.

S&F in repair 32mm bore PVC waste pipe for kitchen sink one mtr long complete all as specified and directed.

S&F in repair 40 mm bore PVC waste pipe for kitchen sink one mtr long complete all as specified and directed.

S&F in repair 100mm dia CP grating (Minium weight 25gms) complete all as specified and directed.

S&F in repair PVC connection 15mm size PTMT nuts of length 600mm, complete all as specified and directed.

S&F in repairs Vitreous china squatting pan ‘Orissa’ pattern, size 580 x 440 mm, white with integral foot rests including provision of cement concrete bedding & ‘P’ or ‘S’ trap complete all as specified and directed. [MAKE:-SOMANY (Cat.No.121115), PRAYAG (Cat No.4055) or equivalent in CERA/PARRYWARE/ HINDWARE as approved by GE.]

S&F in repairs vitreous china wash down water closet pan, pedestal pattern, ISI marked, white, including plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed. [MAKE:-SOMANY (Cat No.120403 & 120404) or equivalent in CERA/PARRYWARE /HINDWARE as approved by GE.]

S&F in repairs Vitreous china wash basin, ISI marked, white, flat back, size 630 x 450mm, including CP waste coupling, 32mm dia PVC waste pipe of suitable length, brackets and cutting for and pinning in ends of brackets, complete all as specified and directed. [MAKE:-SOMANY or equivalent in CERA/PARRYWARE /HINDWARE as approved by GE.]

S&F in repairs Vitreous china wash basin, ISI marked, white, flat back, size 550 x 400mm, including CP waste coupling, 32mm dia PVC waste pipe of suitable length, brackets and cutting for and pinning in ends of brackets, complete all as specified and directed. [MAKE:-SOMANY (Cat No.110107) or equivalent in CERA/PARRYWARE /HINDWARE as approved by GE.]

S&F in repairs plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminum hinging device complete all as specified and directed. [MAKE:-PRAYAG/SOMANY/CERA/PARRYWARE /HINDWARE]

S&F in repairs PVC low level flushing cistern 10 litres capacity, ISI marked, white, with all fitting and fixtures including brackets, PVC connection of 450mm long and 32 mm bore PVC flush pipe, complete all as specified and directed. [MAKE:- SOMANY (Cat No.121002), Prayag (Cat No.501 Smart flush cistern) or equivalent in PARRYWARE-SLIMLINE/CERA as approved by GE]

S&F in repairs hand shower (health faucet) with 8mm dia 1.0 mter long flexible tube and wall hook complete all as specified and directed. [MAKE:- Prayag (Cat No.BEA-86) or equivalent in JAQUAR/MARC as approved by GE]

S&F in repairs Jet spray (butterfly) with 1 mtr tube complete all as specified and directed. [MAKE:- Prayag (Cat No.BEA-18) or equivalent in JAQUAR / PLUMBER / MARC as approved by GE]

S&F in repairs Toilet paper holder of mild steel Chromium plated ‘D’ type, fixed to walls with chromium plated brass screws complete all as specified and directed. [MAKE:- Prayag (Cat No.BA-48) or equivalent in JAGUAR/CERA as approve by GE]

S&F in repair 40 mm bore PVC flush pipe complete all as specified and directed.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls, 75 mm bore complete all as specified and directed.

S&F PVC (SWR) bends any radius, 75 mm bore complete all as specified and directed.

S&F PVC (SWR) junction single (single T), equal or unequal, 75mm bore complete all as specified and directed.

S&F PVC (SWR) junction single (double T), equal or unequal, 75mm bore complete all as specified and directed.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) bends any radius, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) junction single (single T), equal or unequal, 110mm bore complete all as specified and directed.

S&F PVC (SWR) floor/Nahani trap, plain with CP grating including jointing with solvent cement, dia of outlet 75 mm complete all as specified and directed.

S&F in repair PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed

Demolition of brickwork built in cement or cement lime mortar complete all as specified and directed.

M&L for Brick work with fly ash ‘B’ bricks (Modular), straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

Taking down aluminium doors n.exe 4 sqm each and refixing in same position after carry out necessary repairs including replacing rubber/ aluminium beading and jointing cleats, tightening if required including making good existing surface complete all as specified and directed. Note :- Any aluminium style , rail, frame, floor spring, hydrulic door closer if required to be replaced will be measured and paid seperately under respective item.

Supplying, fabricating and fixing powder coated (minimum thickness 50 micron) aluminium sections of required size for door windows frames shutters and partitions including aluminium hinges of required size jointing cleats, screws sash fasteners, plug for fixing with walls, columns, etc complete all as specified and directed. [MAKE: JINDAL/ AJIT INDIA/ HINDALCO]

S&F in repair Floor door stopper 150mm long of aluminium ally body and tonge, anodised, with hard drawn steel spring, fixed in floor complete all as specified.

S&F in repairs Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, complete all as specified and directed.

Dismantling water tanks exc 500 ltr cap & n.exc 1000 ltr cap of any size or capacity and removing to store complete all as specified and directed.

S&F Rotational moulded (three layered, ISI marked) polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity including PVC cover, hoisted and fixed in position including connecting up pipes complete all as specified and directed. [MAKE:-SINTEX/ POLYWELL/ POLYCON/POLYPLAST]

S&F Rotational moulded (three layered, ISI marked) polyethylene water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity including PVC cover, hoisted and fixed in position including connecting up pipes complete all as specified and directed. [MAKE:-SINTEX/ POLYWELL/ POLYCON/POLYPLAST]

Dismantling of wall and ceiling boards (Fibre, Pulp, Insulation etc.) or insulation board/slabs/blankets, any thickness including cover fillets complete all as specified

M&L in repairs for galvanised cold rolled steel section framework of size 600 x 600mm grid size using 24x38x0.50 (composite thickness) tee (bottom pre coated) & 24x24x0.50mm (composite thickness) wall angle including suspenders as per manufacturer’s instructions complete all as specified and directed. [Make: GAPSON(Gabsec) or equivalent as approved by GE]

S&F asbestos free calcium silicate board of size 600x600x6mm, fixed to steel frame work in ceiling with & including applying two coats of oil bound distemper complete all as specified & directed. NOTE:- Cost of making frame work for light fittings, etc is deemed to be included in the quoted unit rate

Running welding in repairs thickness of metal to be welded not exc 6mm thick including taking down the article and refixing in position after welding (if required) complete all as specified & directed.

M&L for Water proofing treatment on roof surfaces with APP modified membrane with non woven polyester reinforced, weight not less than 3 KG/SQM and thickness of membrane not less than 3mm having thermal insulation with white mineral/gravel finish on upper side of membrane uniformly embedded during manufacturing process laid in following sequence complete all as specified and directed.:- (a) Applying 10mm thick plaster in CM 1:4 mixed with water proofing compound @ 3% by weight of cement on cleaned roof surface. After properly curing of the plaster, the roof will be tested for water tightening by ponding with water for seven days for any seepage/leakages, etc. If any seepage/leakage is observed the rectification will be carried out by pressure grouting under pressure of 5 Kg/sqcm using cement based grout. After the roof surface is repaired, the slab /roof will be again tested for water tightness before proceeding for further treatment. (b) Properly cleaning and drying of the plastered roof surfaces, parapets, gutters, drain mouths, etc for all foreign matters such as fungus, moss, dust, etc by wire brushing and dusting. Proper grooves shall be cut around CI drain outlets/pipes/chimney pipes and other similar situations to tuck in the treatment. (c) Applying a coat of bituminous primer conforming to IS: 3384-1965 @ 0.3Kg/Sqm on the prepared surface till the surface is properly impregnated. (d) Laying APP modified water proofing membrane with 100mm overlap in longitudinal direction and 100mm overlap in transverse direction sealed and bounded to the surface by torch application method. (e) All joints and changes in direction should be curved with cement mortar 1:3 with SBR latex @ 200ml per bag of cement and cured well before laying the membrane. A fillet of PCC 1:2:4 type B0 using 12.5mm graded stone aggregates shall be provided at all junctions of vertical and horizontal surfaces and wherever there is change of direction. (f) Topping will be done with precast machine pressed 20-22mm thick PCC tiles (using grey cement) of size 250 x 250 mm or 300 x 300mm, conforming to IS-1237 (hydraulically pressed), laid over 15mm thick cement mortar screed in CM (1:4), set & jointed in neat cement. Joints of tiles shall be 2-3mm wide and grouted with chemical ‘Tile Grout’ of M/s Asian Paints or equivalent as approved by GE.

All as per Item No. 115.00 here in before but with plain membrane without mineral finish, complete all as specified and directed

Disconnecting of existing tanks, setting aside (or lowering if required) for repair, cleaning, etc. and hoisting if required reconnecting and refixing in position capacity of tank exc 1000 ltr & n. exc 2000 ltr, complete all as specified and directed. Note :- Rate inclusive of temporary connection for supply of water.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone agg) as in foundation, filling, sub-base and mass concrete, complete all as specified and directed.

M&L Providing Cement Concrete Type B1, 1:2:4 (20mm graded coarse aggregate) as in flooring all specified and directed.

M&L for heavy duty flooring tiles, harsh weather & UV Resistance, high abrasion resistance, MOH Hardness >6, thickness 10 mm thick, area of each tile not less than 0.09 sqm, anti slip type, laid in floors, steps, edges, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tile with & including 15mm thick rendering in CM 1:4 complete all as specified and directed. [MAKE: SOMANY/ KAJARIA/ORIENT/JOHNSON]

M&L for Factory made, machine pressed, M-35 grade concrete interlocking paver blocks (glossy /reflective type), with grey cement and pigment, any shape and size conforming to IS:15658-2006 (ISI Marked) of 60 mm thickness with & including 50 mm thick stone dust cushion and joints filled with sand complete all as specified and directed. [MAKE:- MEHTAB / NAVYA TILES / SAP PAVERS/ SAGAR TILES]

M&L for Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cills, seismic and other similar bands, plinth courses, copings, bed plates, bond stones, etc including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.

M&L for Providing precast reinforced cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate in louvers and jallies 35mm thick (measured solid) including all mouldings but excluding frame and set in cement mortar 1:4 complete all as specified and directed.

S&F 12mm thick toughen glass as in glazing to doors in approved shape & design with and including necessary steel fittings & fixtures such as 500mm long stainless steel handle fixed both sides in each shutter, lock fixed with floor/wall/ceiling, floor spring, hinges, etc complete all as specified and directed.

M&L for Metalic ceiling T 24 plain board of size 600x600 thickness 0.5 to 0.7mm fixed to steel frame work as in ceiling, including galvanised cold rolled steel section frame work including taking down old ceiling, complete all as specified and directed. Make Fresco Industires Pvt Ltd or equivalent as approved by GE.

M&L for Providing, cement concrete type B0 1:2:4 (12.5 mm graded aggregate) mixed with water proofing compound @ 3% by wt of cement in benching, roof kerbs of mud stops, rounded or chamfered on edges, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, complete all as specified and directed. (Note :- Water Proofing compound shall be measured and paid seperately)

M&L for Chequered cement concrete tiles with grey cement and no pigments 250mm x 250mm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with & including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

S&F Door closer hydraulically regulated, designation No 2, universal type, suitable for door shutters of 701 to 850mm in width and weight between 36 to 60 KG and fixed, complete all as specified and directed.

Taking down old glazed stoneware drain pipes 150 mm bore, as specified complete all as specified and directed.

S&F Salt glazed stoneware drain pipes 150 mm bore, grade ‘A’, laid in trenches and jointed as specified complete all as specified and directed.

M&L for Concrete bed to drain pipes 150 mm bore including packing under and completely surrounding pipes with concrete after they are laid and tasted; in cement concrete 1:4:8 type D2 using 40mm graded stone aggregate complete all as specified and directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick each layer as in soil complete all as specified and as directed.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Schedule of credit (calculation will be done off line) Rs. 18280.00

Samaksh Enterprises

M/S BRIJLAL UPADHYAY

M/S AJAY JAIN

M/S Shanti Traders

RAJPATI CONSTRUCTION

SHIV SHANKAR MISHRA

deepak mehra & associates