MAINT AND MISC CIVIL REPAIR WKS TO CERTAIN OTM AND MD ACCN AT K AREA ZIRAKPUR AND SEC 28/29D UNDER GE CHANDIGARH

Amount

Taking down wooden Chowkhats or frames exc 1.5 sqm but not exc 4.00 sqm ech but with shutters (without taking off shutters from the frames ) complete all as specified

S&F 125 x 60 mm pressed steel frames for doors 1.25 mm thick with one or more rebates incl necessary fixing lugs,hinges lock, strike plate etc,including making good in cement mortar complete all as specified and directed.

S&F 105x60mm pressed steel frames for doors,1.25 mm thick with one or more rebates incl necessary fixing lugs,hinges lock, strike plate etc including making good in cement mortar complete all as specified and directed.

M&L plain cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate, as for back filling the chowkats, as in coping, bed plates including necessary form work and weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed by Engr-in-charge

M&L for providing cement concrete 1:3:6 type C1 (using 20 mm graded crushed stone aggregate) in blocks for fixing hold fasts & pressed steel frames for doors complete all as specified and directed

Taking down wooden shuters exc 1.5 sqm but n.exc 4.00 sqm each , complete all as specified and directed

S&F Mild steel bolts, diameter of neck exc 12 n exc 20mm purpose made, with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut, exc 30cm long complete all as specified and directed .

S&F factory made 35mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type with one faces are covered with decorative face veneer with lipping/frame to match, all as specified & directed by Engr-in-Charge.

S&F factory made 35mm thick second class hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc, sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats including shop coat of primer complete all as specified and directed .

M&L for preparing new wooden surface of any description over 10cm width or girth and painting with two coats of synthatic enamel paint over a coat of pink primer complete all as specified

S&F Continuous (piano) hinges, brass, bright finish or electrogalvanised with width of flap 40mm dia complete all as specified and directed.

S&F 125 mm Brass handles, cast type, polished bright complete all as specified

S&F 40mm dia brass, cupboard knobs fixed with nut, screw and washer of brass, brightfinished complete all as specified and directed

S&F 100 mm Hasp and staple, safety type,brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed

S&F 140 mm Floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring,fixed in floor complete all as specified and directed

S&F 50 mm long magnatic catcher of brassalloy body superior quality and fixed with screw complete all as specified

S&F in repair stainless steel cutlery pan basket or any other basket of any description/pattern as approved by GE fixed with sliding channel revolving wheels , fixed to wood based frame work , complete all as specified and directed

S&F in repair stainless steel auto close (dada) hinges suitable for PVC moulded shutter fixed in position with staianless steel screw complete all as specified and directed

S&F in repair telescopic channel 400-500 mm long and fixed in position with stainless steel screws , ISI marked , suitable for cupboard drawers , complete asper the sample kept in the office of Engr-in-charge

S&F solid PVC door frame of size 50mmx47mm made out 5mm plain colour PVC sheet reinforced with MS square tube made as per specification and drawing.

M&L Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottomrails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail;Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, lippling & fixing in the frame at site as per specification & drawing.

S&F factory made box type steel windows / ventilators with side hung shutters including hinges, steel handle, steel peg stay and MS tower bolt 150mm long complete with 8mm dia glazing bars , dovetailed or welded as per Drg No TD-277R sheet 1/4 to 4/4 of HQ CE CZ Chandigarh complete all as specified and directed.

S&F factory made box type steel windows / ventilators with side hung shutters including hinges, steel handle, steel peg stay and MS tower bolt 150mm long complete without glazing bars , dovetailed or welded as per drawing No TD-276R sheet 1/4 to 4/4 of HQ CE CZ Chandigarh and making good as existing surfaces complete all as specified and directed. Note for item No 22 & 23 :- Glass / wire gauge shall be measured and paid separately.

S&F 4.00 mm thick Sheet glass,ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F in repair 3.00 mm thick Sheet glass,ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane including hacking out old broken glass of any size from wooden/ steel frames complete all as specified and directed.

All as item No. 25 above but frosted glass.

S&F Stainless steel wire cloth.0.36mm nominal dia of wireand average width of aperture 1.40mm and fixed withstainless steel wire staples complete all as specified and directed.

S&F in repair Stainless steel wire cloth.0.36mm nominal dia of wireand average width of aperture 1.40mm and fixed withstainless steel wire staples complete all as specified and directed.

M&L preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F 150 mm size MS door spring including roller and roller plate by means of welding or screwing down complete all as directed.

S&F for 100 mm PVC butt hinges for PVC doors complete all as specified and directed

S&F door stopper 100 mm of aluminium alloy body with rubber bottom complete all as specified and directed.

S&F aluminium handles, cast type, anodised of size 150 mm all as specified & directed.

S&F aluminium anodised, barrel tower bolts of extruded section 200 long complete all as specified and directed .

S&F aluminium alloy, anodised, sliding door bolt 300mm long with hasp, stapple (bolt type) and fixing clips of sheet, cast or extruded sections complete all as specified and directed .

M&L for framed work as in doors or gates of angle of any section with gusset plates, rails, braces etc. complete drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and incl either hooks and hinges or steel hanging door fittngs (including of mild steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing inluding dismantling of doorshutter and door frame complete all as specified.

M&L for complete removal of existing treatment of walls including preparation of the surfaces properly and applying two coats of oil bound distemper over and including 1 mm wall care putty to achieve smooth surfaces, complete all as specified and as directed

M&L for prepration of old ceiling surfaces and applying one coat of white wash on ceiling ,complete all as specified.

M&L for preparation of old painted steel and iron surfaces by brooming or by steel wire brushing, scrapping down smpke soot,moulds, moss and efflorescent salts and treading oil and greasy spots, of any description over 10cm girth or width not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted wooden surfaces by brooming or by steel wire brushing, scrapping down smoke soot,moulds, moss and efflorescent salts and treading oil and greasy spots, of wood and wood based materials of any description over 10cm girth or width not otherwise described and applying one coat of synthetic enamel paint all as specified and as directed.

M&L for preparation of old distempered surfaces by brooming or by steel wire brushing, scrapping down smoke soot,moulds, moss and efflorescent salts and treading oil and greasy spots, not otherwiseof walls including corinces pillars etc and applying one coat of oil bound distemper, all as specified and directed.

All as per sl item No 41 here-in-before but on ceilings.

M&L for light coloured vitrified tiles 8 mm to 9 mm thick (square rectangular) area of each tile not exceeding 0.36 sqm laid as in floors, set and jointed with cement slurry over & including 15mm thick bedding of layer of cement sand mortar (1:4) and pointed with coloured cement to match with surfaces of tiles complete all as specified and as directed.

All as per ser item No 43 but in vertical surfaces such as skirting over and including 10 mm thick rendering in CM (1:4) , complete all as specified and directed .

S&F single piece WC of size 365x655x765mm with flushing cistern and connection pipe, P or S trap (closed pattern incl all necessary accessories like rag bolts, kitt /gel gasket etc, (including flushing cistern, pvc seat cover , jet and flush pipe complete all as specifed and directed.

S&F for 16mm dia Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors incl elbow, socket, reducers etc., including taking down of GI tubing 15 mm dia ,complete all as specified and directed .

M&L rendering 15mm thick in CM (1:6) on fair faces of brick work or concrete surfaces, including taking down cement plaster on bricks or stone walls etc., including raking out joints, hacking for key scrubing down with water etc , and removing rubbish out of MD land all as specified and directed .

M&L for preparation of new plastred surfaces of walls and applying two coat of oil bound distemper over and including 1mm thick wall care putty, all as specified and directed.

M&L rendering 10mm thick in CM (1:4) on fair faces of brick work or concrete surfaces, including taking down cement plaster on bricks or stone walls etc. including raking out joints, hacking for key scrubing down with water etc including removing rubbish out of MD land all as specified and directed .

M&L for preparation of new plastred surfaces of walls and applying two coat of cement based paint over a coat of primer, all as specified and directed.

M&L rendering 10mm thick in CM (1:3) on fair faces of brick work or concrete surfaces, including taking down cement plaster on bricks or stone walls etc., including raking out joints, hacking for key scrubing down with water etc including removing rubbish out of MD land complete all as specified and directed .

M&L for preparation of new undecorated surfaces and applying three coat of white wash on ceiling, complete all as specified and directed .

S&F in repairs for 18/19 mm thick HDHMR board both side liminated and fixed with screws in cup board shutters/ shelves and kitchen cabinets including beading and lippingall as specified & directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area not exc. 1.5 sqm each and removing from site complete all as specified and directed.

M&L mild steel work in framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165

S&F Aluminium anodised hasp and staple 100 mm , safety type, brass with hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed .

Demolition of brick work built in cement mortar including all quoins arches pillars complete all as specified and directed.

M&L for Brick work with sub class 'B' bricks, class Designation 100 Kgf/cm2 (Approx) straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed.

All as per item No 58 above but except old size sub class `B bricks.

S&F in repairs Vitreous China wash basin white flat back of size 550x400mm with CP waste coupling & pipe complete all as specified and directed by Engr-in-Charge.

S&F in repairs PVC waste pipes 32 mm dia suitable for basins/ sink / urinals complete all as specified and directed.

S&F in repair 15 mm Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for 15 mm bore iron pipe and fixed complete all as specified.

S & F in repair 450 mm long PVC connections 15mm size with PTMT nuts complete all as specified and as directed.

M&L for Brickwork with fly ash modular bricks in cement mortar, straight or curved on plan exc 6m mean radius, built in in CM 1:6 all as specified.

M & L for modular bricks with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in built in cement mortar 1:4 in walls ,complete all as specified and directed by Engr-in-Charge.

S & F of Stainless steel Kitchen Rack 30 inch x 36 inch x 10 inch with adequate shelves and sections Heavy gauge wall mounted with fitting screws, complete all as specified and directed

Demolition of reinforced cement concrete in any position at any height and removing rubbish out of MD land complete all as specified and directed.

M&L for Reinforced cement concrete 1:2:4 , type B-1(using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams, shelves and the like complete all as specified and directed.

M&L for repairing the edges of concrete chajjas, facias, slabs, columns & the like by providing PCC (1:2:4) type B-0 including all necessary form work and/or provision of rendering 15 mm thick (average thickness) in cement mortar (1:3), after applying a coat of cement slurry @ 3 kg/ Sq. m of surface, finished even and fair, surface area not exceeding 450 mm wide, in patches including taking down swoolen/damaged plaster or concrete complete all as specified.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished of concrete flat surfaces complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia & over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and building with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for 16 mm to 18 mm thick granite slab (table rubbed polished) as in cooking platform , jamb, cill, step & riser setted and jointed with cement slurry and bedded over & including 15mm thick bedding layer of cement sand mortar (1:4), & pointed with white/ coloured cement including cutting, rounded and chamfered edges etc complete all as specified and as directed.

Dismantling of floor hearth or wall tiles including cement mortar but not backing and removing rubbish out of MD land complete all as specified and directed.

M&L for roughening the surfaces of old cement concrete floor by picking, cleaning and washing down with water to remove dust etc.

M&L for coloured non-skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including screed bed or bedding layer of 15mm thick in CM (1:6) , complete all as specified and directed .

All as per ser item No 74 but in vertical surfaces such as skirting over and including 10 mm thick rendering in CM (1:4) , complete all as specified and directed .

M&L for coloured non-skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including screed bed or bedding layer of 15mm thick in CM (1:6) , complete all as specified and directed .

M & L for coloured ceramic glazed ceramic tiles in vertical surface 450X 300X 7-8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade/colour of tiles,over and including 10 mm thick rendering in CM (1:3) , complete all as specified and directed .

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid,bedded and pointed in any mortar and removing rubbish out of MD land complete all as specified

M&L for 18-20mm thick machine cut kota stone slab flooring over 15 mm thick cement screed base laid in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing and including cutting, grinding, rounded and chamfered edges and granite polishing etc complete all as specified and as directed.

All as per item No.80 above but in skirting /dado etc over 10 mm thick rendering in cement mortar (1:4) complete all as specified.

Taking down AC rain water pipe any size or pattern incl all fittings heads, shoes, bends. Swan necks, etc including cleaning for refixing or removing to store.

Dismantling of PVC /cast iron pipes 75/100 mm fixed in any position complete all as specified and directed .

S&F PVC (SWR) 110 mm bore pipes single socketed, in any lengths with rubber ring joints, fixed to wall with PVC clamp complete all as specified and directed.

S&F PVC (SWR) 75 mm bore pipes single socketed, in any lengths with rubber ring joints, fixed to wall with PVC clamp pipe 75 mm , including taking down PVC complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bend of any radius with acess door complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bend of any radius with acess door complete all as specified and directed.

S & F in repairs 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed .

Cutting chases through brick walls pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps , cills, sunshades, shelves, lintels etc and cutting chases for concealed water tubing.(Girth n exc 10 cm)

S&F 16 mm CPVC SDR -11 brass elobw complete all as specified and directed

S&F 16 mm CPVC SDR -11 brass Tee complete all as specified and directed

S&F 16 mm CPVC SDR -11 Male Brass Threaded Adaptor MTA/MBTAcomplete all as specified and directed

S&F 16 mm CPVC SDR -11 Female Brass Threaded AdaptorFTA/FBTA complete all as specified and directed

S&F 16 mm CPVC SDR -11 Tank Adaptor complete all as specified and directed

S&F in repair 16 mm CPVC SDR -11 Union complete all as specified and directed

S&F in repair 16 mm CPVC SDR -11 Ball Valve complete all as specified and directed

S&F for 20mm dia Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors incl elbow, socket, reducers etc., including taking down of GI tubing 20 mm dia ,complete all as specified and directed .

S&F 20 mm CPVC SDR -11 brass elobw complete all as specified and directed

S&F 20 mm CPVC SDR -11 brass Teecomplete all as specified and directed

S&F 20 mm CPVC SDR -11 Male Brass Threaded Adaptor MTA/MBTAcomplete all as specified and directed

S&F 20 mm CPVC SDR -11 Female Brass Threaded Adapto rFTA/FBTA complete all as specified and directed

S&F 20 mm CPVC SDR -11 Tank Adaptor complete all as specified and directed

S&F in repair 20 mm CPVC SDR -11 Union complete all as specified and directed

S&F in repair 20 mm CPVC SDR -11 Ball Valve complete all as specified and directed

Dismantling wrought iron or mild steel work (incl connected wooden posts in stair cases) of any description not otherwise provided for complete all as specified and directed

Material & Labour for providing and fixing stainles steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement , complete all as specified and directed.

Demolition of cement concrete as in ground floors and in paving n. exc 15cm thick above ground floors and removing rubbish out of MD land complete all as specified and directed.

M&L for 75 mm thick PCC (1:3:6 ) type C-2 using 20 mm graded stone aggregate as in plinth protection laid in panels finish the top surfaces even and smooth without using extra cement

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern) P or S type white with seat cover white (exluding fixing bolts, flushing cistern and flush pipe all as specified.

S&F in repairs Vitreous China Squatting pan, 'Orissa pattern, size 580x440 mm white with integral foot rests including PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float,hockey stick and handle including brackets,complete all as specified

S&F in repair 110mm PVC(SWR)'' P''/''S'' Trap complete all as specified and as directed.

S&F PTMT grating doom 125mm dia with or without hole. (min wt 40gms) complete all as specified and as directed.

S&F in repair Chromium plated brass 2 in 1 health faucet with hook 1mtr tube complete all as specified and directed.

S&F for stop valve (concealed type) cast copper alloy fancy type chromium plated with long shank and cup screwed down, and fixed with 15mm bore iron pipe as in repair complete all as specified and as directed.

S&F in repairs Belmonte Ceramic Vitreous China wash basin oval shape Table Top/over Counter vessel 500 x 380 x 120mm with CP waste coupling & pipe complete all as specified and directed .

Supply & fix in repairs PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action with top push type button with inlet ball valve and float including flush pipe, ball valve, handle, bracket PVC short bend etc. complete all as specified and directed.

S&F in repairs 15mm dia bib tap, chromium plated brass, fancy type long body with crutch or butterfly handle, screwed down complete all as specified and directed.

S&F in repairs 15mm dia CP Center hole mixer (for hot and cold water), screwed for iron pipe complete all as specified and directed.

S&F in repairs 15mm bore CP angle cock/ Concealed Stop valves fancy type,screwed down,high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

M&L in repairs brass chromium plated shower rose 125mm size with or without swivel joints with shower arm 15 mm size, 195mm long with bend of 45 degree with flange , including fixing to steel pipe or union all as specified and directed.

S&F in repairs chromium plated towel rail 60 cm long 20mm dia with flanges complete all as specified and directed.

S&F in repair stainless steel sink, 1.00mm thick for kitchen overall size 495mm x 420mm with bowl size 410mm x330mm x 160mm including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets, waste coupling, PVC waste pipe, washers, connecting union etc complete all as specified and directed.

Dismantling of PVC water storage tanks capacity 1000 ltr complete all as specified and directed.

S&F rotational moulded polyethylene (tripple Layer) water storage tanks 1000 Ltr capacity (cylindrical vertical with closed top) hoisted including tank Adoper inlet and outlet and fixed in position all as specified in SSR Part-I, complete all as specified and directed.

S&F 20mm ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed complete all as specified and directed by Engr-in-Charge

M&L for Endura digital tiles, heavy duty ,for high traffic 300 x300 mm x 10mm thick, non skid acid and scratch resistance, fixed with 3 mm spacer & filled with grout breaking strength not less than 1700N as in floor jointed in neat cement slurry ,including 15mm thick screed bed cement mortar 1:6 and dismantling of tiles complete all as specified and as per direction of manufacturer’s instruction complete all as specified and directed.

S&F in repair Harrison rails, Stainless steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and directed

S&F in repair 15 mm stainless steel jet spray complete set all as specified and directed

S&F in repair glass corner shelf, one set comprises of three pieces of corner shelf fancy type (small to large) 250 x 250mm, 200 x 200mm, 150 x 150mm) with all fittings,complete all as specified.

S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws,complete all as specified.

Dismantling wall and ceiling boards (fibre pulp, insulation, etc) or insulation boards/slabs/blankets any thickness including cover fillets.

M&L for 9 mm thick PVC pre liminated gypsum board as in ceiling including anodised aluminium snap grid frame work for ceiling having grid size 605 x 605 mm comprising of wall angle of size 25 mm x 25 mm x1.30 mm, main runner of size 38 mm x 26 mm x1.30 mm. The grid system will be suspended at every 1200 mm c/c in both directions by using 3.5 mm dia aqualine wire fixed to purline or RCC roof with suitable fastners to withstand the lood of grid system with ceiling board complete all as specified and directed.

Dismantling Asbestos cement (corrugated, semicorrugated,plain etc.) sheets in roof coverings complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or fixed to wall using hold fast including dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and directed.

Ditto as item No 135 here-in-before but plain sheet as in Ridge complete all as specified and directed.

M& L for 6mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc Fixed with L-type or screws J-type or cranked hook bolts complete all as specified and directed

S&F 2 mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc incl dismantling existing sheet complete all as specified and directed.

S&F MS rolled sections as in roof trusses (framed), trussed,purlins, rails and fastenings and bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. similar work conforming to Fe-410-W(Gde-E-250) ,complete all as specified and directed .

B N FRIENDS AND CO

MOHAMMAD RASHID