Electrical work for Improvement in lighting of various shops at HAL, Lucknow

Light/Fan/Exhaust Fan Point wiring

Supply & making One Light point/fan point/exhaust fan point/call bell point controlled by one modular type switches, 6 Amps 230 Volts with 1.5 sqmm, P.V.C. insulated, copper FRLS type conductor multi stranded wire of 1100/660 Volts grade in heavy duty P.V.C. pipe with modular switch, modular plate, suitable GI box and earthing the point with 1.5 Sq mm FRLS PVC insulated copper conductor single core etc. including all accessories such as bends, J.B,tees, ceiling rose, batten holder etc. required for point wiring work. The pipe shall be laid concealed in wall; partially it may be flush to the wall as per site requirement.

Add to the above Item-1 for each addition on only light points on the same switch circuit including all materials required for such wiring work.

Supply & making One (half point) with 5 pin, 6 Amps modular socket controlled by 6 Amps switch modular type on the same board with other switches with 1.5 sqmm, PVC. insulated,copper FRLS type conductor, multi stranded wire.

Sub-main/Circuit Wiring

Wiring for circuit /submains wiring alonghwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface /recessed heavy duty class PVC conduit as required Make: Finolex/Polycab/Havells

Power Point / Industrial Point

Supply & making One independent industrial power point 20 Amps,240 V socket outlet with 2 pole and earth metal enclosed plug top alongwih 20A C curve ,SP, MCB, in sheet steel enclosure in recess with chained metal cover for the socket outlet and complete with connections, testing & commissioning etc as required.

Supply & making One independent domestic power point with 3 pin, 5/6 Amps modular socket controlled by 5/6 Amp modular switch, including 3 module GI box along with modular base and cover plate for modular switches, connections to switches etc as required.

Supply & making One independent domestic power point with 3/5 pin, 15/16 Amps modular socket controlled by 15/16 Amp modular switch, including 3 module GI box along with modular base and cover plate for modular switches, connections to switches etc as required.

Cable Dressing

Supplying and fixing of 25MM of Heavy class PVC conduit for dressing of LAN/WAN/telephone cable along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. (Make: AKG/CAP/Anchor/GM)

Supply of non-metallic polyamide/nylon flexible conduit of outer dimension 28mm (+/-1mm) manufactured to BS EN 61386/EN60529 with conduit gland (25 nos), conduit coupler (100 nos.), 90 Deg elbow (25 nos), Tee (25 nos.), lock nuts ( 50 nos), rubber end cap (10 pcs) Make: Connectwell/Trinity touch

Supply of non-metallic polyamide/nylon flexible conduit of outer dimension 54mm (+/-1mm) manufactured to BS EN 61386/EN60529 with conduit gland (25 nos), conduit coupler (100 nos.), 90 Deg elbow (25 nos), Tee (25 nos.), lock nuts ( 50 nos), rubber end cap (10 pcs) Make: Connectwell/Trinity touch

MCB DB

Supply & installation of MCB DB, single phase,double door,suitable for incorporating MCB's,8 way with following incoming & outgoings MCB's. Incoming- 63 Amp, DP MCB Isolator -01 No. Outgoings: 10-25 Amp SP, MCB – 06 No. The D.B. must be installed flush to the wall and wall must make good after fixing.

Supply and installation of three phase, double door MCB DB suitable for incorporating MCB's, 4 way per phase with following incoming and out goings MCB's Incoming- 63 Amps, TPN Isolator,:MCB-01 No., Outgoings: 10-32 Amps S.P. MCB –12 Nos. The D.B. must be installed flush to the wall and wall must make good after fixing.

Supply and installation of three phase, double door MCB DB suitable for incorporating MCB's, 6 way per phase with following incoming and out goings MCB's Incoming- 63 Amps, TPN Isolator,:MCB-01 No., Outgoings: 10-32 Amps S.P. MCB – 18 Nos. The D.B. must be installed flush to the wall and wall must make good after fixing.

Power Cable

Supply/Laying

Supply & Laying of XLPE insulated, PVC sheathed Armored, 1.1 KV grade, Aluminium conductor power cable, conforming to IS 7098 (Part-I). Concealed cabling can be done to cut/chase the wall/floor, laying cable tray (provided by HAL) and after laying of cable wall/floor shall be finished as original & if cable laid on wall then use clamps for fixing the cable. The work also includes connection work which includes all the required materials for their jointing work. Cable to be laid as required at site and as per the direction of Engineer-In-Charge. (a) Size of cable 4 core x 25 sqmm

End/Straight Trough Joint

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (a) 4C x 25 Sqmm.Al Arm LT cable.

GI Wire

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Removal of Old Wiring

Removal of old Cables, Wires, Light Fitting, fan and DB, MCB DB and all other accessories required to meet the scope of work at site and at nearby location like passage, Gallery etc after tracing of live and non live wires of electrical, Lan and Telephone thereafter dressing of cable as directed by EIC.

Lighting Fixtures

Supply and installation of recess mounting LED luminaire of size 600 mm x600 mm 35/36W 220 V AC with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp including connecting up with driver three core flexible copper cable by replacing existing 2x36 W false ceiling lights. Gap is to be filled by 2x2 false ceiling tiles. The work also includes connection from ceiling rose to fitting with twin core, white color flat wire of 1100/660 Volts grade. All material required for the work shall be supplied by the contractor. Any gap created on account of replacing the light shall be suitably filled by contractor without any extra cost for safety of lights and personnel working under. Ligths to be supplied with required bracket/frame to install the light direct on surface (Qty 100 Nos.). Cost to be quoted accordingly.

Specifications of light: - Driver with light sources Engine type: LED - Luminous Flux not less than 4200 Lumen - Luminous Efficay not less than 120 lm/W - Beam Angle of light source 120 Deg - Power consumption not greater than 36 W - Power factor not less than 0.9 - Protection Class IEC Safety Class I - Surge Protection (Common Differential) level until 4kV differential mode and 4 kV common mode - Housing material: Steel - Optic material: Polystyrene - Optical cover material : Polycarbonate - Housing color: White RAL9016 - Ingress Protection : IP20 - Mechanical Impact Protection: IK02 - Overtime performance: 50000 Hours Locations: SU30 (I)/TTC/Inst Factory/Pilot Oxygen/ERM/Flight Control/NC-III Make: Crompton/Philips Note: 100 Drivers to be supplied along with light within the supplied cost as spare.

Supply of single module 100 W fan Regulator as per site requirement Make: L&T/Honeywell/Roma

Supply and Fixing Following modules GI Box along with modular base & cover plate for modular switches in recess etc as required. The work includes removing of old damaged boxes and coveer plate etc. Make: L&T/Honeywell/Roma

Supply and Fixing Following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc as required. Make: L&T/Honeywell/Roma

Supply & installation of IEC compliant 95W (power factor 0.95) LED high bay lights with safety chain cool white at the height of 15-20 feet approximately. Contractor has to take necessary safety precautions while installation the lights. To make the necessary civil/electrical damages good as original shall be contractors responsibility. Material: Precision die cast aluminium Burning Hours: 50000 Hours Ingress Protection: IP 20 Mechanical Protection Impact: IK 08 Mounting : Eye Bolt Optic Material: Polycarbonate Power Consumption: 95 W Power Factor: 0.95 Beam angle: 90 Deg Luminous Efficacy: 160 lm/W Surge protection: 6 kV Make: Philips/Crompton

Supply of 12 W False ceiling LED downlights (CCT: 4000K) Make: Philips/Crompton

SUBTOTAL

GST @18% on SUB TOTAL

TOTAL

Name of Vendor:

Note: Please refer chapter 6(B) of Technical Bid documents for recommended make of equipments to be used in the project, if it is not specially mentioned in the price bid.

HINDUSTAN AERONAUTICS LIMITED ACCESSORIES DIVISION, LUCKNOW PQ FORM/ELIGIBILITY CRITERION-MATRIX

NAME OF THE WORK: “Electrical work for Improvement in lighting of various shops at HAL, Lucknow ”

Estimated Cost (in Rs.)

Name of the Individual / Firm / Company: * Mandatory

Type of ownership Pvt. Ltd./ Proprietorship/Partnership/ Public limited/ Govt. Agencies/ Trust If Other, please specify

Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, Contractor registration No etc.,

Address of Correspondence

Contact Details: Contact person name: Designation: Mobile No:. Ph. No. with STD code: Email Id :

Contractor must give his acceptance to provide services as per ‘Requirement, Scope of work, Drawings’ and ‘Terms & Conditions' contained in Technical Bid.

Self attested copy of PAN Registration certificate issued by income tax authority.

Sel attested Copy of GST Registration Certificate.

DECLARATION I

The document being viewed / downloaded from the website and having read & understood all the contents of the tender document mentioned under terms and conditions including price bid do hereby accept all the terms and conditions laid down in the said Tender document and will abide by the same on acceptance and ward of work.

DECLARATION II

I/We declare and confirm that - 1. All information and attachments submitted along with this offer are true and correct. 2. I/We are aware that any false information provided herein will result in the rejection of my offer . 3. I/We shall not make refund claims of expenditure incurred in processing this offer. 4. I / We aware that document sought only be uploaded for evaluation of offer. 5.I/We are not debarred / blacklisted from any Govt agencies, if debars for specified period reason for debar and copy of resumption of same shall be provided. 6. I/We have not concealed any information which may adversely effect my qualification.

DECLARATION III

I/We declare and confirm that all the documents required for technical qualifications mentioned at SI.No.2 and 3 of Techincal Bid document have been attached with the technical bid.

Name of Bidder:

* 1. To be filled by Bidder essentially and carefully. Supporting documents must be attached as proof. Clarifications shall be sought w.r.t. information provided with tender documents. 2. Similar works implied that works related to LT/HT Electrical Works in nature. Mere supply of electrical goods does not mean qulification in the tender. 3. Scanned copy of completed work orders and completion certificate issued by respective clients to be attached. If the completion certificate is form private organization the same shall be uploaded with TDS certificate. 4. The work shall be completed as a whole, Partial value/completion will not be considered. 5. The Bidders are requested to attach scan copies of all the relevant / desired / required proofs/ documents on e-portal, failing which tender shall be summarily rejected without assigning any reason to bidders.