PROVISION OF RECEPTION ROOM AT DRONACHARYA OFFICERS MESS, RAIN WATER HARVASTING AT DIARY FARM, FLOORING, SANITARY, GEYSER AND EXHAUST FAN AT BUILDING NO P 66, P 67 P 68 UNDER GE CENTRAL BANGALORE

Amount

B/R PORTION : Surface dressing n.exc 15 cm deep as in soft/loose soil and disposal to a distance not exc 50m complete all as specified and directed.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation, etc area not exceeding 10 Sqm on plan and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed.

Removing excavated material to a distance exc 250m but not exc 500m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

M & L for treating the backfill in contact with foundation at the rate of 7.50 litres of emulsion per square metre of vertical surface (Area of sub structure in contact with backfill to be measured)

M & L for treating the top surface of filled earth at the rate of 5.00 litres of emulsion per square metre of surface area.

M & L for treating the soil under plinth protection at the rate of 5.00 litres of emulsion per square metre of surface area.

M & L for treating the soil along the external perimeter of building at the rate of 2.50 litres of emulsion per metre of the perimeter wall. (MAKE of ATT chemical for item No. 5 to 8 : DURSBAN/TRISUL/CHLOROXA/LETHAL)

M&L for precast cement concrete block masonry type C1, 1:3:6 (20 mm graded granite stone aggregate) with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M & L for Plain cement concrete 1:2:4, type B-1, (using 20 mm graded stone aggregate) as in coping, kneelers, bed plates etc including weathering slightly rounded or chamfered angles including necessary form work complete all as specified and directed.

M & L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

M & L for Plain cement concrete 1:3:6, type C-1 (using 20 mm graded stone aggregate) as in surface channels and drains, etc complete all as specified and directed.

M & L for 75mm thick Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in sub-base of floor, etc complete all as specified and directed.

M & L for 25mm thick Plain cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in level course of floor, etc complete all as specified and directed.

M & L for non-skid, ceramic, coloured tiles, Grade B II(a), 8 to 10 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm, in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for ceramic, coloured tiles, Grade B II(a), 8 to 10 mm thick as in vertical surfaces of wall /skirting to match the length of floor tile procured under No 15 above including 10 mm thick screed bed in cement mortar 1:3 set & jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for glazed ceramic, coloured tiles, Grade B I(b), 7 to 8 mm thick area of each tiles not exc 0.06 sqm as in skirting/ dado/ vertical surfaces of wall including 10 mm thick screed bed in cement mortar 1:3 set & jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for precast chequered cement concrete tiles of size 30cm x 30cm x 25mm thick, as in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and directed.

M & L for cement concrete 1:3:6, type C1 as in kerb or mud stop, rounded or chamfered on edges complete all as directed.

S & F aluminium anodised coloured powder coated (minimum thickness of powder coating 50 micron) frame for doors, windows and ventilators with one or more rebates including jointing cleats for fixing etc.

S&F aluminium anodised coloured powder coated (minimum thickness of powder coating 50 micron) fixed/sliding type window/ventilators, aluminium sections weighing not less than 0.50kg per metre, all are made of from aluminium anodised section including necessary track, jointing cleat, glazing clips, rubber packing anodised aluminium snap beading, screws of suitable size and stainless steel wire cloth, locking arrangement, etc complete all as specified and directed by the Engr-in-Charge.

S & F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty/timber beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S & F 4 mm thick, sheet glass, figured/ pin headed glass and glazing with oil putty/timber beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

M & L for plain cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) for embedding holdfast, bed block, cills, etc including necessary form work complete all as specified and directed.

S & F Mild steel small articles using flat iron such as band, strap, hold fast, cleat, support, hook, hinges, base tie for door frame etc and other similar items conforming to Fe-290, Gde E-165 including retaining with tar or coat tar black paint complete all as specified and as directed.

M & L for precast cement concrete solid building blocks, 1:3:6, type C-1 (using 20mm graded stone aggregate) or slab 10 cm thick (with plain or interlocking joints as directed) setting in cement mortar 1:4 complete all as specified and directed.

M & L for moorum/sand/red bajri filling under floors or in foundations laid in layers n exc 15cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M & L for Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

M & L for Precast Reinforced Cement Concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in cover slab of drain, etc and set in cement mortar 1:4 including necessary form work, moulds, etc complete all as specified and directed by the Engr-in-Charge. (Note : Reinforcement shall be measured and paid separately)

M & L for Reinforced Cement Concrete M-25 design mix as in foundation, footings foundation beams, plinth beams etc complete all as specified and directed.

M & L for Reinforced Cement Concrete M-25 design mix as in columns, pillars, piers, post and struts etc complete all as specified and directed.

M & L for Reinforced Cement Concrete M-25 design mix as in beams, cantilevers, lintel beam etc complete all as specified and directed.

M & L for Reinforced Cement Concrete M-25 design mix as in slabs supported on walls, beams and column in floors, roofs, landings, balconies and in shelves and the like complete all as specified and directed.

M & L for Reinforced Cement Concrete M-25 design mix as in chajjas etc complete all as specified and directed.

M & L for use & waste Form work to sides of concrete foundations, footings, raft beams, sides and soffits of plinth beams and the similar works for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste Form work to sides of concrete columns, pillars, piers, post and struts and the similar works for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings, balconies and in shelves and the like for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste Form work to sides and soffits of concrete chajjas and the similar works for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste Form work to soffits and sides of beams, lintel beam for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste Form work to sides/edges of concrete flats, floor and roofs, in walls, horizontal or slopeing and the similar work, 10cm to 20cm wide for rough finished surfaces of concrete complete all as specified and directed.

S & F TMT steel bars 10mm dia and over, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F TMT steel bars 6 to 8mm dia, cut to length, bend to shape required, including cranking, bending spirally as in tie/stirrups of columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F TMT steel bars 6 to 10mm dia, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for Mild steel framed work such as grills, gratings, door, gates etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bar, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S & F well seasoned 2nd class hard wood plain, solid, straight chowkat and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints including treating the timber libarally brushed at least twice with oil or kerosene based solusion of chlorophyrifos 20EC 1.0 % (by weight) concentration complete all as specified and as directed.

M&L for 35 mm thick 2nd class hard wood factory made glazed/gauzed skeleton shutters for door, open rebated and prepared to receive glass, gauze etc (without sash bars), edges framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc; size of the members of shutters as specified in SSR Part- I, Section 8, clause 8.24(a) complete all as directed.

S&F 35mm thick Flush shutters, solid core construction, with block coard core & plywood face panels commercial type on both side conforming to IS 2202 (Part- I) -1999, including internal liping beading all round fixed as in Door Shutter,Cup board shutter & Kitchen rack all as specified.

S & F second class hard wood fillets, wrought, square rectangular or triangular in section secured with nails, cross sectional area exc 3 and not exc 6 sqcm etc including two coat of painting using synthetic enamel paint over a coat of pink primer to exposed surfaces complete all as specified and directed.

S & F second class hard wood fillets, wrought, square rectangular or triangular in section secured with nails, cross sectional area exc 13 and not exc 25 sqcm etc including two coat of painting using synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S & F 18/19mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work, complete, as specified and directed

S & F continuous (Piano) hinges, mild steel bright finished or electro galvanised, width of flaps 30mm when open complete all as directed.

S&F for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed

S & F 100 mm size, butt hinges, medium weight, cold rolled complete all as specified, and directed.

S & F 150 mm long, Aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and directed.

S & F 125 mm size, Aluminium handles, cast type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S & F aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, length of bolt of 300 mm anodised finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S&F aluminium anodised body and tounge door stopper with hard drawn steel spring, 150mm size fixed to door all as directed.

S & F 100mm size extruded brass handle, cast type, polished bright complete all as directed.

S&F brass lock for drawer,50mm, grade - 1, 4 lever with minimum 2 keys all as directed.

S&F 25mm dia stainless steel curtain rods all as specified and directed.

S&F brass moulded decorative type curtain brackets all as specified and directed.

M & L for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection laid in proper slope/gradient etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

M & L for Hardcore of broken/crushed stone aggregate of gauge n.exc 63 mm deposited, spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for rendering 15 mm thick in cement mortar 1:4 on other than fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 10 mm thick in cement mortar 1:6 on other than fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 15 mm thick in two layer (10mm + 5mm thick) on fair faces of brick work or concrete surfaces in cement mortar 1:4, mixed with water proofing compound at top 5mm thick layer by weight of cement as per manufacturer's instructions and finished the surface even and smooth without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item).

M & L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces of ceiling and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

"Supply only" liquid water proofing compound complete all as specified and directed. (Make : Dr FIXIT/Fosroc/choksey)

M & L for Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and directed.

M & L for preparing newly plastered surfaces of internal walls, etc and applying two coats of distemper oil emulsion over a coat of primer including 1 to 2mm thick wall care putty complete all as specified and directed.

M & L for preparing newly plastered surfaces of ceiling, etc and applying two coats of distemper oil emulsion over a coat of primer including 1 to 2mm thick putty complete all as specified and directed.

Cutting into existing manholes for inserting new drain pipe, 110mm bore and making good to pipe and rendering, cutting out existing benching for and forming branch channel in cement concrete 1:2:4 type B1 finished to match with existing complete all as directed.

Cutting into existing manholes for inserting new drain pipe, 150mm bore and making good to pipe and rendering, cutting out existing benching for and forming branch channel in cement concrete 1:2:4 type B1 finished to match with existing complete all as directed.

M & L for Plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggragate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore SGSW drain pipes complete all as specified and directed.

M & L for Salt glazed stone ware drain pipes 150 mm bore, grade 'A' laid in trenches, jointed and tested complete all as specified and directed.

M&L for rendering 10mm thick in CM 1:3 mixed with water proofing compound by weight of cement as per manufacturers instructions finished even & smooth without using extra cement on roof/floor. Note: WPC shall be measure and paid seperatly under supply only item.

M&L for Applying oil bound bitumen primer @ 0.20 kg/sqm and providing 3mm thick APP modified water proofing membrane weighing not less than 3.6 kg/sqm reinforced with non woven polyester matt weighing not less than 160 gm/sqm having softening point not less than 150mm centigrade, having tensile strength of 650 N/sqcm and 350 N/sqcm in longitudinal and transverse directions respectively of the reinforced tearing strength of 180N by torch application with minimum 10cm side overlapping and 15cm end lap, applying a coat of blown grade hot bitumen 90/15 over the mebrance @ 1.2 kg/sqm top of membrane surface shall then be finished with solar reflective bituminous aluminium paint @ 0.10 kg/sqm complete all as per manufacturer instructions and as directed by Engineer-in-Charge over roof and wall surfaces.

Supply, laying, connection and testing, 20mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixtures complete to walls and ceilings or laid in floors, etc complete all as specified and directed.

S&F Vitreous China Wash hand basin , white flat back size 550x400 mm including a pair of mild steel angle iron brackets duly painted, erected/embeded in wall, providing Pillar Tap 15 mm bore Chromium plated cast copper alloy with capstan heads, high pressure, fancy type with long screwed shanks and fly nuts, 32 mm waste coupling brass chromium plated suitable for wash hand basins & 32 mm dia LDPE PVC waste pipe, PVC connection 15 mm size 600 mm long including cutting hole and pinning in ends making good disturbed portion using cement mortar 1:3 complete all as specified & directed by Engineer-in-charge.

Supplying and laying of 20mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S & F corner shelf of PTMT fixed with and including chromium plated brass screws in wooden/plastic cleat or rawl plug complete all as directed. (Minimum weight 190 gms).

S & F towel rail, 600 mm long of PTMT fixed with and including chromium plated brass screws in wooden/plastic cleat or rawl plug complete all as directed. (Minimum weight 190 gms).

S & F 15 mm bore, bib taps, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F 15 mm bore, stop valves, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good with cement mortar, cutting exc 10 cm but n.exc 20 cm girth complete all as specified and directed.

S & F low density polythylene pipe 32mm , pressure rating 6Kgf/sqcm, fixed to wall or laid in floor etc including fittings complete all as directed.

S & F high density polythyene pipe 32mm , pressure rating 6Kgf/sqcm, fixed to wall/ceiling or laid in floor etc including fittings complete all as directed.

S & F 32mm dia PVC pipe bend any radious all as directed.

E/M PORTION : Taking down carefully unserviceable aluminium/copper point wiring (light, fan, socket or power) including unserviceable light fittings, switch board complete, switch sockets, ceiling roses, pendants, regulators, sockets, etc and removing materials from site and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M & L for Point wiring surface type, with 1.5 Sqmm (nominal area), FRLS PVC insulated, multistranded, single core unsheathed, copper conductor cables passing through and including providing PVC conduit (Medium grade) with all fittings and accessories (like Tee, bend etc.) complete in walls /ceiling etc. with and including 1.5 Sqmm (nominal area) FRLS, PVC insulated, unsheathed, stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth point and earth dolly including PVC terminal box with 3mm thick masonic laminated sheet top cover fixed on wall with suitable sizes cadmium plated iron screws and washers etc.for mounting switches, sockets, regulators etc complete for one light/fan/bell/buzzer point controlled by one ,one way switches complete all as specified and directed.

All as per item No 92 above but for one 3 pin socket outlet, 5 Amps on Independent board complete all as specified and directed.

All as per item No 92 above but for one 5 Amps, 3/5 pin socket outlet on the same board with other switches complete all as specified and directed.

All as per item No. 92 here in before but wiring with cables of size 2.50 sqmm for wiring & cables of size 2.50 sqmm both (FRLS) as continuous earth wire for one 15 Amps, 6 pin Switch/Socket outlet on Independent board complete all as specified and directed.

All as per item No. 92 here in before but wiring with cables of size 4.0 sqmm for wiring & cables of size 4.0 sqmm both (FRLS) as continuous earth wire for one 15 Amps, 3 pin Switch/Socket outlet on Independent board complete all as specified and directed.

M & L for Point wiring concealed type, with 1.5 Sqmm (nominal area), FRLS PVC insulated, multistranded, single core unsheathed, copper conductor cables passing through and including providing PVC conduit 'medium grade' with all fittings and accessories (like Tee, bend etc.) complete in walls /ceiling etc. with and including 1.5 Sqmm (nominal area) FRLS, PVC insulated, unsheathed, stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth point and earth dolly including MS/pressed steel terminal box (wall thickness 1.2mm) suitable for modular switch, socket, fan regulators etc of suitable module including cutting chases in wall/ceiling and making good using PCC 1:2:4 type B1/ cement mortar 1:4, finished the surfaces smooth to match with the existing for one light/fan/bell/buzzer point controlled by one ,one way switches complete all as specified and directed. NOTE :- Cost element for modular metal flush box and white cover plate/ shall deemed to be included in quoted rate.frame

All as per item No 97 above but for one 3 pin socket outlet, 5 Amps on Independent board complete all as specified and directed.

All as per item No 97 above but for one 5 Amps, 3/5 pin socket outlet on the same board with other switches complete all as specified and directed.

All as per item No. 97 here in before but wiring with cables of size 2.50 sqmm for wiring & cables of size 2.50 sqmm both (FRLS) as continuous earth wire for one 15 Amps, 6 pin Switch/Socket outlet on Independent board complete all as specified and directed.

M & L for Sub main wiring (concealed type) with two runs of 6 sqmm (Nominal area) single core FRLS cable PVC insulated, multistranded, unsheathed, copper conductor cables 1100 Volts grade drawn through PVC conduits, medium grade, of suitable size, fixed to wall/ceiling etc with all accessories, fittings, fixures including 6 sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, FRLS copper conductor as earth wire and duly connected to common earth point including PVC conduits of suitable size, cutting chases in wall/ceiling and making good using PCC 1:2:4 type B1/ cement mortar 1:4, finished the surfaces smooth to match with the existing complete all as specified and as directed by Engineer-in-charge. (Note : PVC Conduits, two run wiring cables and one run of earth wire will be measured as one length.)

S & F switch piano, 5 Amp, single pole, flush type one way 230 volts complete all as specified and as directed.

S & F Switch socket combination, 2 in 1, 5 Amps (bearing ISI marked), flush type, 240 volts complete all as specified and directed.

S & F Switch socket combination, 5 in 1, 5/15 Amps (bearing ISI marked), 240 volts, flush type complete all as specified and directed.

S & F modular switch 6 Amp, 1 module, flush type one way 230 volts complete all as specified and as directed.

S & F modular switch 16 Amp, 1 module, flush type one way 230 volts complete all as specified and as directed.

S & F modular bell push, 6 Amp, 1 module, flush type one way 230 volts complete all as specified and as directed.

S & F calling bell, Ding Dong type, AC 230 volts, single pole complete all as directed.

S & F modular socket, 2/3 pin combination, 6 Amp, 2 module, flush type one way 230 volts complete all as specified and as directed.

S & F modular socket 5/6 pin combination, 6/16 Amp, 2 module, flush type one way 230 volts complete all as specified and as directed.

S & F modular fan regulator 5 step high speed, 120 Watt and above, 2 module, 230 volts, ergonomically designed directional knob with 360 degree rotation , ISI marked complete all as specified and as directed.

S & F single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one 20 Amp MCB, SP, 'C' curve 10KA breaking capacity complete all as specified and as directed.

S & F Ceiling rose, 3 phase/PVC/polycarbonate (bearing ISI marked), isolated body including providing PVC square/round block complete all as specified and directed.

S & F Stepped type(five steps) electronic fan regulator flush type complete all as specified and directed. (Make: Anchor, Model No. 14502 or equivalent make as per list of manufacturer)

S & F Factory made distribution board (DB), Double Door in sheet steel enclosure fitted with common bus bar neutral link, earth bar and din rail, SPN, 8 way, 240 Volts IP-43, IK-09, suitable for housing MCB's complete all as directed.

S & F MCB, SPN, 240 Volts, 40/63 Amps, 'C' Series, 10KA breaking capacity complete all as specified and directed.

S & F MCB, 'C' Series, SP, 240 Vlots, 6 to 32 Amps, 'C' Series, 10KA breaking capacity complete all as specified and directed.

Cutting hole/opening through stone masonry wall of 38cm thick suitable for providing 300mm sweep exhaust fan and making good the disturbed surfaces using cement mortar 1:4 or PCC 1:2:4, type B1 as required including toothing and bonding, finished the surfaces to match with existing ie white/colour wash as required complete all as directed.

Supply and Fixing exhaust fan, 300mm sweep metal body, AC single phase 230/240 Volt including bird free louver shutter cut to fit with hole for exhaust fan including providing holes grouting bolts and 3 core flexible copper conductor cable of size 24/0.20 sqmm connecting up from ceiling rose to exhaust fan terminal complete all as directed. Make Havells/Crompton/Orient/Bajaj

Supply and Fixing water heater/gyeser, storage vertical type, any colour, 25 Litre capacity, BEE 5 star rated including suitable PVC connection pipes of suitable size for hot and cold water complete all as directed. Make : HAVELLS, model No: MONZA EC or equivelent of make Bajaj/Crompton/Philips

Supply, laying, connection and testing, 15mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixtures complete to walls and ceilings or laid in floors, etc complete all as specified and directed.

S & F 20 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and directed.

S & F 20 mm bore, gun metal gate valve, with iron wheel head, screwed both ends, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F LED luminare high performance extruded channel, thermally conductive material, 20 watts, 230 volt, wall mounted type with high translucent milky white diffuser for smooth light distribution, all prewired fixed on walls with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and providing & connecting up with twin core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Make : Havells Cat No LUMILINEBS18WIED830SPCWH or equivelent of Philips/Crompton Greaves/Bajaj

S&F LED tube light fitting of 20 watts 6000K , 230 volt, with aluminium extruded channel powder coated with diffuser for glare free light complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Make : Havells/Crompton Greaves/Bajaj

S&F bldg security light light fittings 1x 15 Watt LED street light with cast aluminium housing, toughened flass diffuser, IP65/66 and wired with all accessories and including connection up with twine core twisted flexible copper conductor cable with 1.5 M long suitable size all as specified and directed. Make Havells/Bajaj/phillips/CG

Supply & Fixing 5 star rated energy saving ceiling fan 1200mm sweep (white) with all accessories and hanging the ceiling fan from fan hook with 3 core flexible copper wire 24/0.20 sqmm from ceiling rose, etc all as directed. Make : Model ES-50 of Havells or equivalent in Usha/Orient/Crompton.

S&F security light bracket made out of 25 mm bore GI Light grade 1.00 M long to required shape as in bracket for steet light fittings fixed with two pair of MS flate iron clamp of size 50mm X 6 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flate iron surface with two coates of synthetic enamel paint over a coat of red oxide primer complete including taking down unserviceable one all as specified and directed.

Supply and laying cable UG XLPE insulated screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10.00 Sqmm 2 core including alumunium lugs etc for connecting complete all as specified and directed. (Note: Excavation and earth work shall be measured and paid seperately under respective item)

Supply and laying well burnt bricks (Kiln burnt), locally available best quality laid breath wise across the length of cable in trenches for protection of UG cables complete all as specified and directed.

M & L for Sand cushioning and covering with clean dry sand in trenches for protection of under ground cables (below, above and around the cable laid in trenches) complete all as specified and directed. (Note: Thickness after punning down shall be measured for payment)

Supply, laying, 50mm bore, Steel water tubing, galvanised, light grade with all fittings and fixtures for cable protection on road/drain/floor or for hangging ceiling fan etc including providing MS clamp, bolt, nuts complete all as specified and directed.

M & L Earthing complete with Galvanised steel earth plate electrode 600 mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with the top edge of earth plate at depth not less than 1.5 m below ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers protected by 15mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, pre-cast RCC 1:2:4 type B-1 cover slab of size 350x350x50mm reinforced with 8mm dia TMT steel bars @15cm centre to centre in both direction and 10mm dia MS handle of suitable size, charcoal or coke and salt in alternative layers,necessary earth work in soft/loose soil all as shown in Electrical Plate No 3 of MES Schedule Part I and testing complete as specified and as directed.

Drilling bore hole of suitable dia with reverse rotary circulation or direct circulation method or combination of both by using power rig for housing of 150mm nominal bore casing pipe upto 35 metre depth below ground level in any kind of soil strata complete all as specified and directed.

All same as item No 134 above but from depth 35 metre upto 150 metre depth from ground level.

All same as item No 134 above but from depth 150 metre upto 300 metre depth from ground level.

Supply and fixing/ jointing 150mm dia having 2.5mm wall thick, uPVC casing pipe, heavy duty, 6 kg/sqcm pressure rating bearing ISI marked, lowering in bore well complete all as directed. Make : Supreme/Prince/Finolex/Oriplast

Supply and fixing/ jointing 150mm dia having 2.5mm wall thick,u PVC slotted, heavy duty, 6 kg/sqcm pressure rating bearing ISI marked, lowering in bore well complete all as directed. Make : Supreme/Prince/Finolex/Oriplast

Supply and fixing/ jointing 150mm dia having 2.5mm wall thick, uPVC strainer, heavy duty, 6 kg/sqcm pressure rating bearing ISI marked, lowering in bore well complete all as directed. Make : Supreme/Prince/Finolex/Oriplast

Supply and filling 40mm stone aggregate in pit all as directed.

SHRI NARAYANADRI ENGINEERS & BUILDERS

DIVYA CONSTRUCTIONS